2. ERROR CODE AND SELF-DIAGNOSTIC MODE 2.1 Error Code List The following error codes is displayed at the upper right of the screen when the CLEAR PAPER or CALL SERVICE symbol is blinking. 2.1.1 Jam Error code Contents Troubleshooting E010 Paper exit jam Classification Jam not reaching the exit sensor : The paper which has passed through the fuser unit does not reach the exit sensor. P.
Error code Contents Troubleshooting ADU misfeeding (Paper not reaching the registration sensor): The paper which has passed through ADU does not reach the registration sensor during duplex printing. P. 5-3 E120 Bypass misfeeding (Paper not reaching the registration sensor): The paper fed from the bypass tray does not reach the registration sensor. P.
Error code Contents Troubleshooting Lower drawer transport jam (Paper not reaching the registration sensor): The paper does not reach the registration sensor after it has passed the upper drawer feed sensor. P. 5-10 E220 Lower drawer transport jam (Paper not reaching the upper drawer feed sensor): The paper does not reach the upper drawer feed sensor after it has passed the lower drawer feed sensor. P.
Error code Contents Troubleshooting E550 Other paper jam Classification Paper remaining jam on the transport path: The paper is remaining on the transport path when printing is finished (caused by a multiple paper feeding). P. 5-19 E712 RADF jam Jam not reaching the original registration sensor: The original fed from the original feeding tray does not reach the original registration sensor. P.
Error code EA10 Classification Finisher jam (Finisher section) Contents Troubleshooting Paper transport delay jam: The paper which has passed the bridge unit does not reach the inlet sensor. [MJ-1022/ 1023/1024/1101] P. 5-30 Paper transport stop jam: (1) The paper does not pass through the inlet sensor. [MJ-1022/1023/1024] (2) The paper has passed through the inlet sensor but does not reach or pass the feed path sensor or processing tray sensor.
Error code EA80 Classification Contents Troubleshooting Stapling jam: Stapling is not performed properly. [MJ-1024] P. 5-43 Door open jam: The delivery cover or inlet cover has opened dur-ing printing [MJ-1024]. P. 5-43 EAA0 Power-ON jam: Paper exists at No.1 paper sensor, No. 2 paper sensor, No.3 paper sensor, vertical path paper sensor or delivery sensor when power is turned ON. [MJ-1024] P.
2.1.2 Service call Error code C010 Classification Contents Troubleshooting Main motor abnormality: The main motor is not rotating normally. P. 5-52 C020 Developer motor abnormality: The developer motor is not rotating normally. P. 5-52 C030 Transport motor abnormality: The transport motor is not rotating normally. P. 5-52 PFP motor abnormality: The PFP motor is not rotating normally. (the case that paper can be fed from any drawer except the PFP) P.
Error code Classification Contents Troubleshooting C411 Fuser unit related service call Thermistor or heater abnormality at power-ON: Abnormality of the thermistor is detected when power is turned ON or the temperature of the fuser roller does not rise in a specified period of time after power is turned ON. P.
Error code Contents Troubleshooting Entrance motor abnormality: The entrance motor is not rotating normally. [MJ-1101] P. 5-67 CB11 Buffer tray guide motor abnormality: The buffer tray guide motor is not rotating or the buffer tray guide is not moving normally. [MJ-1101] P. 5-67 CB12 Buffer roller drive motor abnormality: The buffer roller drive motor is not rotating or the buffer roller is not moving normally. [MJ-1101] P.
Error code Contents Troubleshooting Alignment motor abnormality: Alignment motor is not rotating or aligning plate is not moving normally. [MJ-1024] P. 5-72 CBD0 Guide motor abnormality: Guide motor is not rotating or guide is not moving normally. [MJ-1024] P. 5-73 CBE0 Paper folding motor abnormality: Paper folding motor or paper folding roller is not rotating normally. [MJ-1024] P.
Error code Contents Troubleshooting Punch ROM checksum error: Abnormality of checksum value on Hole punch controller PC board is detected when the power is turned on. [MJ-1101 (when MJ-6101 is installed)] P. 5-79 CC72 Punch RAM read/write error: Abnormality of checksum value on Hole punch controller PC board is detected when the power is turned on. [MJ-1101 (when MJ-6101 is installed)] P.
Error code CEA0 Classification Copy process related service call Contents Troubleshooting Revolver home position detection abnormality: It cannot detect that the revolver is at its home position. P. 5-89 Black developer unit lifting movement abnormality: The black developer unit does not move up or down normally (lifting cam does not operate normally). P. 5-90 2nd transfer roller position detection abnormality: The 2nd transfer roller does not contact/release normally. P.
Error code F110 Classification Contents Troubleshooting Communication error between System-CPU and Scanner-CPU P. 5-63 P. 5-63 P. 5-97 F130 Scanner response abnormality Database abnormality: Database is not operating normally. Invalid MAC address F200 Data overwrite kit (GP-1060) is taken off P. 5-98 SLG board abnormality P. 5-65 F111 F120 F350 Communication related service call Other service call Circuit related service call © June 2005 TOSHIBA TEC P.
2.1.3 Error in Internet FAX / Scanning Function 1) Internet FAX related error Error code Classification Troubleshooting 1C10 System access abnormality P. 5-98 1C11 Insufficient memory P. 5-98 1C12 Message reception error P. 5-98 1C13 1C14 Message transmission error Invalid parameter P. 5-98 P. 5-98 1C15 Exceeding file capacity P. 5-98 1C20 System management module access abnormality P. 5-98 1C21 Job control module access abnormality P.
2) RFC related error Error code Message displayed in the TopAccess screen Contents Troubleshooting 2500 Syntax error, command unrecognized HOST NAME error(RFC: 500) Destination mail address error (RFC: 500) Terminal mail address error (RFC: 500) P. 5-101 2501 Syntax error in parameters or arguments HOST NAME error(RFC: 501) Destination mail address error (RFC: 501) Terminal mail address error (RFC: 501) P. 5-101 2503 Bad sequence of commands Destination mail address error (RFC: 503) P.
3) Electronic Filing related error Error code Message displayed in the TopAccess screen Contents Troubleshooting 2B10 There was no applicable job. No applicable job error in job control module P. 5-102 2B11 Job status failed. JOB status abnormality P. 5-102 2B20 2B30 Failed to access file. Insufficient disk space. P. 5-102 P. 5-102 2B31 Failed to access Electronic Filing. 2B32 Failed to print Electronic Filing document.
4) E-mail related error Error code Message displayed in the TopAccess screen Contents Troubleshooting 2C10 Illegal Job status System access abnormality P. 5-104 2C11 Not enough memory Insufficient memory P. 5-104 2C12 2C13 Illegal Job status Illegal Job status Message reception error Message transmission error P. 5-104 P. 5-104 2C14 Invalid parameter specified Invalid parameter P. 5-104 2C15 Message size exceeded limit or max- Exceeding file capacity imum size P.
5) File sharing related error 2D20 Message displayed in the TopAccess screen Illegal Job status Not enough memory Illegal Job status Illegal Job status Invalid parameter specified There are too many documents in the folder. Failed in creating new document.
6) E-mail reception related error Error code 3A10 3A11 3A12 3A20 3A21 3A22 3A30 3A40 3A50 3A51 3A52 3A60 3A61 3A62 3A70 3A80 3A81 3A82 3B10 3B11 3B12 Message displayed in the TopAccess screen MIME Error has been detected in the received mail. MIME Error has been detected in the received mail. This mail has been transferred to the administrator. MIME Error has been detected in the received mail. This mail could not be transferred to the administrator. Analyze Error has been detected in the received mail.
Error code 3B20 3B21 3B22 3B30 3B31 3B32 3B40 3B41 3B42 3C10 3C11 3C12 3C13 3C20 3C21 3C22 3C30 3C31 3C32 Message displayed in the TopAccess screen Content-Type Error has been detected in the received mail. Content-Type Error has been detected in the received mail. This mail has been transferred to the administrator. Content-Type Error has been detected in the received mail. This mail could not be transferred to the administrator. Charset Error has been detected in the received mail.
Error code 3C40 3C41 3C42 3C50 3C51 3C52 3C60 3C61 3C62 3C70 3D10 3D20 3D30 3E10 3E20 3E30 3E40 3F00 3F10 3F20 3F30 3F40 Message displayed in the TopAccess screen Tiff Paper Size Error has been detected in the received mail. Tiff Paper Size Error has been detected in the received mail. This mail has been transferred to the administrator. Tiff Paper Size Error has been detected in the received mail. This mail could not be transferred to the administrator.
2.1.4 Printer function error Following codes are displayed at the end of the user name on the print job log screen. Error code 402F 4031 4032 4033 4034 4035 4036 A221 A222 A290 A291 A292 A2A0 A2A1 A2A2 Contents Page memory size error - 1200 dpi network print is performed by the equipment with 128 MB (standard) memory. HDD full during print - Large quantity image data by private print or invalid network print are saved in HDD.
<> In the setting mode (08-253), the latest twenty groups of error data will be displayed. Display example EA10 99999999 05 06 14 17 57 32 064 064 23621000000 Error code Total counter YY MM DD HH MM SS MMM NNN ABCDEFHIJLO 4 digits 8 digits 12 digits (Year is indicated 3 digits 3 digits 11 digits with its last two digits.
2.2 Self-diagnosis Modes Mode For start Contents For exit Display Control panel check mode [0]+[1]+ [POWER] All LEDs on the control panel are lit, and all the LCD pixels blink. [POWER] OFF/ON - Test mode [0]+[3]+ [POWER] Checks the status of input/output signals. [POWER] OFF/ON 100% C A4 TEST MODE Test print mode [0]+[4]+ [POWER] Outputs the test patterns. [POWER] OFF/ON 100% P A4 TEST PRINT Adjustment mode [0]+[5]+ [POWER] Adjusts various items.
List print mode (9S): The procedure varies depending on the code.
2.2.1 Input check (Test mode 03) The status of each input signal can be checked by pressing the [FAX] button, [COPY] button and the digital keys in the test mode (03). ÅðÃÅíà ÅÐÑÉÛÎà ÅÍÌßÎÌà ÅÚßÈà ±® ÅÝÑÐÇà ÅÜ·¹·¬¿´ µ»§-à øÔÝÜ ÑÒ÷ ÅÝÔÛßÎà ÅÐÑÉÛÎà ÑÚÚñÑÒ øÛ¨·¬÷ Note: Initialization is performed before the equipment enters the test mode. Fig.
[FAX] button: OFF/[COPY] button: OFF ([FAX] LED: OFF/[COPY] LED: OFF) Digital key [1] [2] [3] Button e.g. A Bypass unit connection B ADU connection C D LCF connection Normal display e.g.
Digital key [5] [6] [7] Contents Button Items to check Normal display e.g. e.g.
Digital key [9] Contents Button Items to check e.g. Normal display e.g. A - - - B - - - C - - - D E - - - F [0] Highlighted display Key copy counter connection Not connected Connected G - - H - - - A B - - - C - - - D - - - E - - - F - - - G H - - - Table 1. Relation between the status of the bypass paper width sensor and paper size (width).
[FAX] button: ON/[COPY] button: OFF ([FAX] LED: ON/[COPY] LED: OFF) Digital key [1] [2] Button e.g. e.g.
Digital key [5] Contents Button Items to check e.g. [8] [9] e.g.
Digital key [0] Contents Button Highlighted display Items to check e.g. Normal display e.g.
[FAX] button: OFF/[COPY] button: ON ([FAX] LED: OFF/[COPY] LED: ON) Digital key [1] [2] [3] [4] [5] [6] [7] [8] Contents Highlighted display Normal display Button Items to check - Temperature/humidity sensor (displays temperature inside of the equipment) Temperature/humidity sensor (displays humidity inside of the equipment) Drum thermistor (displays drum surface temperature) - e.g. A B C D E F G H A B C D E F G H A B C D E F G H A B C D E F G H A B C D E F G H © June 2005 TOSHIBA TEC e.g.
Digital key [9] [0] Contents Highlighted display Normal display Button Items to check A B C D E F G H A B C D Dongles for other equipments / Other USB devices Judgement for acceptable USB storage device (*1) - E F G H e.g. e.g. Connectable Not connectable Acceptable Not acceptable - - *1 Be sure to install the USB storage device to the equipment and check if the device can be used with this code.
2.2.2 Output check (test mode 03) Status of the output signals can be checked by entering the following codes in the test mode 03.
Code Function Procedure 201 Upper drawer feed clutch ON/OFF 3 202 Lower drawer feed clutch ON/OFF 3 203 Lower transport clutch (high speed) ON/OFF 3 204 Bypass feed clutch ON/OFF 3 205 Lower transport clutch (low speed) ON/OFF 3 206 LCF pickup solenoid ON/OFF 3 207 LCF end fence reciprocating movement 2 208 LCF end fence motor ON/OFF 3 209 LCF feed clutch ON/OFF 3 210 LCF transport clutch ON/OFF 3 218 Key copy counter count up 2 225 PFP transport clutch ON/OFF 3 226 P
Code Function Procedure 413 Internal cooling fan ON/OFF (high speed) 3 416 IH board cooling fan (high speed) ON/OFF 3 417 Ozone exhaust fan (low speed) ON/OFF 3 418 Ozone exhaust fan (high speed) ON/OFF 3 419 Developer bias (Black) [AC] ON/OFF 3 420 Developer bias (Color) [+DC] ON/OFF 3 421 Developer bias (Color) [-DC1] ON/OFF 3 422 Developer bias (Color) [AC] ON/OFF 3 424 1st transfer roller bias [+] ON/OFF 3 425 1st transfer roller bias [-] ON/OFF 3 426 2nd transfer rolle
2.2.3 Test print mode (test mode 04) The embedded test pattern can be printed out by keying in the following codes in the test print mode (04). ÅðÃÅìà ÅÐÑÉÛÎà øݱ¼»÷ ÅÍÌßÎÌà Ѱ»®¿¬·±² ݱ²¬·²«±«Ì»-¬ Ю·²¬·²¹ ÅÝÔÛßÎà ÅÐÑÉÛÎà ÑÚÚñÑÒ øÛ¨·¬÷ ÅðÃÅìà ÅÐÑÉÛÎà øݱ¼»÷ ÅÍÌßÎÌà ݱ´±® -»´»½¬·±² ÅÍÌßÎÌà ÅÝÔÛßÎà Ѱ»®¿¬·±² ݱ²¬·²«±«Ì»-¬ Ю·²¬·²¹ ÅÝÔÛßÎà ÅÐÑÉÛÎà ÑÚÚñÑÒ øÛ¨·¬÷ Notes: 1.
2.2.4 Adjustment mode (05) Items in the adjustment mode list in the following pages can be corrected or changed in this adjustment mode (05). Turn ON the power with pressing the digital keys [0] and [5] simultaneously in order to enter this mode. When the power should be turned OFF, be sure to shut down the equipment by pressing the [ENERGY SAVER] button for a few seconds.
Procedure 6 ÅÜ·¹·¬¿´ µ»§Ã øݱ¼»÷ ÅðÃÅëà ÅÐÑÉÛÎà ߫¬±³¿¬·½ ¿¼¶«-¬³»²¬ ÅÍÌßÎÌà ÅÚßÈà ÅÝÑÐÇÃ÷ øÌ»-¬ ½±°§÷ ÅÐÑÉÛÎÃÑÚÚñÑÒ øÛ¨·¬÷ öÅÝßÒÝÛÔà ±® ÅÝÔÛßÎà * When the automatic adjustment ends abnormally, an error message is displayed. Return to standby screen by pressing the [CANCEL] or [CLEAR] button.
Test print pattern in Adjustment Mode (05) Operation: One test print is printed out when the [FAX] button is pressed after the code is keyed in at Standby Screen. Code Types of test pattern Remarks 1 Grid pattern (Black) Refer to 3.4.3 Printer related adjustment 3 Grid pattern (Black/Duplex printing) Refer to 3.4.3 Printer related adjustment 4 For gamma adjustment (Color/Black integrated pattern) Refer to 3.5.1 Automatic gamma adjustment 5 For gamma adjustment (Color) Refer to 3.5.
Notes: 1. The digit after the hyphen in Code of the following table is a sub code. 2. In RAM, the NVRAM of the board in which the data of each code is stored is indicated. M stands for the LGC board and SYS stands for the SYS board.
Code Classification 229-0 Transfer 229-1 229-2 229-3 230-0 Transfer 230-1 231-0 Transfer 231-1 232-0 Transfer 232-1 234-0 Transfer 234-1 Adjustment mode (05) Default Func- 2nd transfer Single ALL 144 roller bias out- side (black) <0-187> put adjustReverse ALL 119 ment side at (black) <0-187> (Thick paper duplexing 1) Single ALL 125 side (color) <0-187> Reverse ALL 112 side at (color) <0-187> duplexing 2nd transfer roller bias outALL 153 put (Thick paper 2) (blac
Code Classification 237-0 Transfer 237-1 238-0 Transfer 238-1 239-0 Transfer 239-1 241 242 Main charger 243 244 Adjustment mode (05) Default Func- 2nd transfer roller bias offALL 5 setting adjustment (black) <0-10> (Thick paper 2) ALL 5 (color) <0-10> 2nd transfer roller bias offALL 5 setting adjustment (black) <0-10> (Thick paper 3) ALL 5 (color) <0-10> 2nd transfer roller bias offALL 5 setting adjustment (black) <0-10> (OHP film) ALL 5 (color) <0-10> Main charger Y
Code Classification 254 Transfer Items 2nd transfer roller bias output voltage 255 Adjustment mode (05) Default Func- -Low ALL -500 <-99990> -High RAM Contents M Transformer output setting of the 2nd transfer roller bias (minus output). When replacing the high-voltage transformer, the values listed in attached data sheet are entered. (Unit: V) The temperature of the inside of the equipment is displayed.
Code Classification 291-0 Transfer 291-1 292-0 Transfer 292-1 293-0 Transfer 293-1 293-2 293-3 293-4 294-0 Transfer 294-1 294-2 294-3 296-0 Transfer 296-1 296-2 296-3 297-0 Transfer 297-1 298-0 Transfer 298-1 299-0 299-1 Transfer Adjustment mode (05) Default Func- 2nd transfer roller bias offALL 131 setting adjustment (black) <0-187> (Thick paper 3) ALL 131 (color) <0-187> 2nd transfer roller bias offALL 119 setting adjustment (black) <0-187> (OHP film) ALL 11
Code Classification 305 Scanner Adjustment mode (05) Default Func- Image location adjustment ALL 124 of secondary scanning <92-164> direction (scanner section) RAM Contents SYS When the value increases by 1, the image shifts by approx. 0.137 mm toward the trailing edge of the paper. When the value increases by 1, the image shifts by approx. 0.0423 mm toward the front side of the paper. Moves carriages to the adjusting position. (Chap. 3.4.
Code Classification Adjustment mode (05) Default Func- Color developer bias DC ALL 100 (-) calibration voltage 1 <70-130> (low) Color developer bias DC ALL 900 (-) calibration voltage 2 <810(high) 990> Procedur e RAM Contents M 1 338 Image control 339 Image control 340 Scanner Reproduction ratio adjustment of secondary scanning direction (scanner section) ALL 127 <0-255> SYS 350 Scanner Shading position adjustment Original glass ALL SYS RADF ALL 128 <1
Code Classification 361 Scanner Adjustment mode (05) Default Func- Log table switching for ALL 0 RADF copying (color) <0-4> 362 RAM Contents SYS 0: Same log table as the one used at copying with original glass 1: Background reproduction - Light 2 2: Background reproduction - Light 1 3: Background reproduction - Dark 1 4: Background reproduction - Dark 2 0: Same log table as the one used at copying with original glass 1: Background reproduction - Light 2 2: Background r
Adjustment mode (05) Default Func- RADF original guide width ALL adjustment (Minimum) Code Classification 367 RADF 368 RADF RADF original guide width adjustment (Maximum) ALL - - 372 Image control ALL 100 <70-130> M 373 Image control Black developer bias DC (-) calibration voltage 1 (low) Black developer bias DC (-) calibration voltage 2 (high) ALL 900 <810990> M 380-0 Image control Image quality open-loop control/ contrast voltage initial value display
Code 383-0 383-1 Classification Image control 383-2 383-3 384-0 384-1 Image control 384-2 384-3 385-0 385-1 Image control 385-2 385-3 386-0 386-1 Image control 386-2 386-3 388 Image control 389 390-0 390-1 390-2 390-3 © June 2005 TOSHIBA TEC Adjustment mode (05) Default Func- Laser power Y ALL 92 actual value <0-255> display M ALL 92 <0-255> C ALL 92 <0-255> K ALL 92 <0-255> Laser power Y ALL 408 actual value <0-999> display M ALL 408 <0-999> C ALL 408 <0-999> K AL
Code 391-0 Classification Image control 391-1 391-2 391-3 Adjustment mode (05) Default Func- Output value LowdenALL 0 display of sity pat<0-1023> image quality tern Y sensor LowdenALL 0 sity pat<0-1023> tern M LowdenALL 0 sity pat<0-1023> tern C LowdenALL 0 sity pat<0-1023> tern K Light amount adjustment ALL 0 result of image quality sen<0-255> sor RAM Contents M Displays the output value of image quality sensor when a low-density test pattern is written.
Code Classification 417-0 Image 417-1 417-2 417-3 418-0 Image 418-1 418-2 418-3 421 Drive 422 424 Drive Adjustment mode (05) Default Func- Color deviaK ALL 128 tion correc<118tion 1 138> (A3/LD) C ALL 128 <118138> M ALL 128 <118138> Y ALL 128 <118138> Color deviaK ALL 128 tion correc<118tion 2 138> (A3/LD) C ALL 128 <118138> M ALL 128 <118138> Y ALL 128 <118138> Adjustment of secondary PPC/ 127 scanning direction reproPRT <0-255> duction ratio (fine adjustFAX 144 men
Code Classification 430 Image 431 Image 432 Image 433 Image 434-0 Image 434-1 Image 435 Image 436 Image 437 Image 438 Image 439 Image 440 Laser 441 442 443 444 445 Adjustment mode (05) Default Func- Top margin adjustment PPC 26 (blank area at the leading <0-255> edge of the paper)) Left margin adjustment PPC 0 (blank area at the left of the <0-255> paper along the paper feeding direction) Right margin adjustment PPC 15 (blank area at the right of <0-2
Code 448-0 448-1 Classification Paper feeding 448-2 448-3 449-0 449-1 Paper feeding 449-2 449-3 450-0 450-1 Paper feeding 450-2 450-3 452-0 452-1 Paper feeding 452-2 452-3 © June 2005 TOSHIBA TEC Adjustment mode (05) Default Func- Paper aligning Long ALL 15 amount size <0-63> adjustment at Middle ALL 15 the registrasize <0-63> tion section Short ALL 15 (PFP upper size 1 <0-63> drawer / Plain Short ALL 15 paper) size 2 <0-63> Paper aligning Long ALL 15 amount size <0-6
Code 455-0 455-1 Classification Paper feeding 455-2 457 Paper feeding 458-0 Paper feeding 458-1 458-2 460-0 460-1 Paper feeding 460-2 461-0 461-1 Paper feeding 461-2 462-0 462-1 Paper feeding 462-2 462-3 463-0 463-1 463-2 Paper feeding Adjustment mode (05) Default Func- Paper aligning Long ALL 8 amount size <0-63> adjustment at Middle ALL 8 the registrasize <0-63> tion section Short ALL 12 (Duplex feed- size <0-63> ing / Plain paper) Paper aligning amount ALL
Code 466-0 466-1 Classification Paper feeding 466-4 466-5 466-6 466-7 467 Paper feeding 468-0 Finisher 468-1 468-2 469-0 469-1 Paper feeding 469-2 469-3 470-0 470-1 Paper feeding 470-2 470-3 471-0 471-1 Paper feeding 471-2 471-3 © June 2005 TOSHIBA TEC Adjustment mode (05) Default Func- Adjustment of Plain ALL 143 paper pushpaper <0-255> ing amount / Post card ALL 170 Bypass feed<0-255> ing Thick ALL 143 paper 1 <0-255> Thick ALL 143 paper 2 <0-255> Thick ALL 143
Code 472-0 472-1 Classification Paper feeding 472-2 472-3 473 Paper feeding 474-0 Paper feeding 474-1 474-2 475-0 475-1 475-2 475-3 475-4 475-5 475-6 475-7 475-8 475-9 Paper feeding Adjustment mode (05) Default Func- Paper aligning Long ALL 15 amount size <0-63> adjustment at Middle ALL 15 the registrasize <0-63> tion section Short ALL 15 (PFP lower size 1 <0-63> drawer / Thick Short ALL 15 paper 1) size 2 <0-63> Paper aligning amount ALL 15 adjustment at the registra
Code Classification 494 Laser 495 496 497-0 Laser 497-1 497-2 497-3 497-4 497-5 498-0 Laser 498-1 499 Development 501 Image 503 504 505 Image 506 507 508 Image 509 510 © June 2005 TOSHIBA TEC Adjustment mode (05) Default Func- Secondary When ALL 135 scanning data decelerat<0-255> laser writing ing to 1/2 start position When ALL 135 decelerat<0-255> ing to 1/3 When ALL 140 decelerat<0-255> ing to 1/4 Adjustment of Upper ALL 128 drawer sidedrawer <0-255> ways de
Code Classification 512 Image 514 515 532 Image 533 534 570 Image 571 572 580 Image Adjustment mode (05) Default Func- Density Photo PPC 128 adjustment (black) <0-255> Fine adjustText/Photo PPC 128 ment of auto(black) <0-255> matic density Text PPC 128 (black) <0-255> Range correc- Text/Photo PPC 40 tion Back(black) <0-255> ground peak Photo PPC 16 adjustment (black) <0-255> Text PPC 40 (black) <0-255> Range correc- Text/Photo PPC 22 tion on origi(black) <11-14, n
Code Classification 590-0 Image 590-1 590-2 591-0 Image 591-1 591-2 592-0 Image 592-1 592-2 596-0 Image 596-1 596-2 597-0 Image 597-1 597-2 598-0 Image 598-1 598-2 599-0 Image 599-1 599-2 600 Image 601 602 © June 2005 TOSHIBA TEC Adjustment mode (05) Default Func- Adjustment of L PPC 128 gamma bal(black) <0-255> ance (Text/ M PPC 128 Photo) (black) <0-255> H PPC 128 (black) <0-255> Adjustment of L PPC 128 gamma bal(black) <0-255> ance (Text) M PPC 128 (black
Code Classification 604 Image Adjustment mode (05) Default Func- Sharpness Text/Photo PPC 0 adjustment (black) <0-31> RAM Contents SYS When the value increases, the image becomes sharper. When the value decreases, the image becomes softer. The smaller the value is, the less the moire becomes. * The default value 0 is equivalent to 16 (center value). Adjustment of the smudged/faint text.
Code Classification 693 Image Adjustment mode (05) Default Func- Range correc- Text/Photo PPC 22 tion on origi(black) <11-14, nal set on the 21-24, RADF 31-34, 41-44> Contents SYS Sets whether the values of the background peak and text peak are fixed or not. Ones place is an adjustment for automatic density and tens place is for manual density. Once they are fixed, the range correction is performed with standard values.
Code Classification 725 Image 729 825 Image 826 827 828 830 Image Adjustment mode (05) Default Func- Density Photo FAX 128 adjustment (black) <0-255> automatic Text/Photo FAX 128 density fine (black) <0-255> adjustment Range correc- Text/Photo SCN 12 tion on origi(black) <11-14, nal manually 21-24, set on the 31-34, original glass 41-44> Text SCN 12 (black) <11-14, 21-24, 31-34, 41-44> Photo SCN 12 (black) <11-14, 21-24, 31-34, 41-44> Gray scale SCN 12 (black) <11-
Code Classification 840 Image Adjustment mode (05) Default Func- Sharpness Text/Photo SCN 0 adjustment (black) <0-31> RAM Contents SYS When the value increases, the image becomes sharper. When the value decreases, the image becomes softer. The smaller the value is, the less the moire becomes. * The default value 0 is equivalent to 16 (center value).
Code Classification 880-0 Image 880-1 880-2 881-0 Image 881-1 881-2 882-0 Image 882-1 882-2 883-0 Image 883-1 883-2 884 Image 953-0 Image Adjustment mode (05) Default Func- Adjustment of L SCN 128 gamma bal(black) <0-255> ance (Text/ M SCN 128 Photo) (black) <0-255> H SCN 128 (black) <0-255> Adjustment of L SCN 128 gamma bal(black) <0-255> ance (Text) M SCN 128 (black) <0-255> H SCN 128 (black) <0-255> Adjustment of L SCN 128 gamma bal(black) <0-255> ance (Photo)
Code Classification 954-0 Image 954-1 954-2 954-3 955-0 Image 955-1 955-2 955-3 956-0 Image 956-1 956-2 956-3 976 Maintenance 1000 Image 1001 1002 1003 © June 2005 TOSHIBA TEC Adjustment mode (05) Default Func- Color deviaK ALL 128 tion correc<118tion 4 138> (A4/LT) C ALL 128 <118138> M ALL 128 <118138> Y ALL 128 <118138> Color deviaK ALL 128 tion correc<118tion 5 138> (A4/LT) C ALL 128 <118138> M ALL 128 <118138> Y ALL 128 <118138> Color deviaK ALL 128 tion corre
Code Classification 1010-0 Image 1010-1 1010-2 1011-0 Image 1011-1 1011-2 1012-0 Image 1012-1 1012-2 1013-0 Image 1013-1 1013-2 1014-0 Image 1014-1 1014-2 1015-0 Image 1015-1 1015-2 1016-0 Image 1016-1 1016-2 1017-0 Image 1017-1 1017-2 1018-0 1018-1 1018-2 Image Items Color balance adjustment for Y (PS/ 600x600dpi/ Smooth) Color balance adjustment for M (PS/ 600x600dpi/ Smooth) Color balance adjustment for C (PS/ 600x600dpi/ Smooth) Color balance adjustment for K (PS/ 600x600dpi/
Code Classification 1019-0 Image 1019-1 1019-2 1020-0 Image 1020-1 1020-2 1021-0 Image 1021-1 1021-2 1022-0 Image 1022-1 1022-2 1023-0 Image 1023-1 1023-2 1024-0 Image 1024-1 1024-2 1025-0 Image 1025-1 1025-2 1026-0 Image 1026-1 1026-2 1027-0 Image 1027-1 1027-2 © June 2005 TOSHIBA TEC Items Color balance adjustment for M (PS/ 1200x600dpi/ Smooth) Color balance adjustment for C (PS/ 1200x600dpi/ Smooth) Color balance adjustment for K (PS/ 1200x600dpi/ Smooth) Color balance adjust
Code Classification 1028-0 Image 1028-1 1028-2 1029-0 Image 1029-1 1029-2 1030-0 Image 1030-1 1030-2 1031-0 Image 1031-1 1031-2 1032-0 Image 1032-1 1032-2 1033-0 Image 1033-1 1033-2 1034-0 Image 1034-1 1034-2 1035-0 Image 1035-1 1035-2 1036-0 1036-1 1036-2 Image Items Color balance adjustment for C (PCL/ 600x600dpi/ Smooth) Color balance adjustment for K (PCL/ 600x600dpi/ Smooth) Color balance adjustment for Y (PCL/ 600x600dpi/ Detail) Color balance adjustment for M (PCL/ 600x600
Code Classification 1037-0 Image 1037-1 1037-2 1038-0 Image 1038-1 1038-2 1039-0 Image 1039-1 1039-2 1040-0 Image 1040-1 1040-2 1041-0 Image 1041-1 1041-2 1046-0 Image 1046-1 1047-0 Image 1047-1 1048-0 Image 1048-1 1049-0 Image 1049-1 1050-0 Image 1050-1 © June 2005 TOSHIBA TEC Items Color balance adjustment for K (PCL/ 1200x600dpi/ Smooth) Color balance adjustment for Y (PCL/ 1200x600dpi/ Detail) Color balance adjustment for M (PCL/ 1200x600dpi/ Detail) Color balance adjustmen
Code Classification 1055 Image 1056 1057 1058 1060 Image 1065 Image 1066 Image 1070 Image 1071 Adjustment mode (05) Default Func- Upper limit in toner saving PRT 176 mode (color) <0-255> PRT 176 (color) <0-255> PRT 176 (color) <0-255> PRT 176 (color) <0-255> Reproduction ratio fine SCN 128 adjustment of primary (color) <0-255> scanning direction Image 1076 Image 1081 1087 1088 Image When the value decreases, the printing density becomes lighter.
Code Classification 1550 Image 1551 1552 1553 1554 1560 Image 1561 1562 1563 1564 1570 Image 1571 1572 1573 1574 1580 Image 1581 1582 1583 1584 1612 Image 1613 1614 1615 1616 © June 2005 TOSHIBA TEC Adjustment mode (05) Default Func- Density Text/Photo PPC 128 adjustment (color) <0-255> manual denText PPC 128 sity fine (color) <0-255> adjustment/ Printed PPC 128 Center value image (color) <0-255> Photo PPC 128 (color) <0-255> Map PPC 128 (color) <0-255> Density
Code Classification 1630 Image 1631 Items Maximum text density adjustment 1632 1633 1642 Image Automatic gamma adjustment 1643 Adjustment mode (05) Default Func- Y PPC 5 (color) <0-10> M PPC 5 (color) <0-10> C PPC 5 (color) <0-10> K PPC 5 (color) <0-10> Color/ PPC Black Color RAM Contents SYS When the value increases by 1, the maximum text density of each color becomes darker.
Code Classification 1698 Image 1699 1700 1701 1702 1708 Image 1709 1710 1711 1712 1725 Image 1737 Image 1738 1739 Adjustment mode (05) Default Func- Manual offset- Text/Photo PPC 128 ting adjust(color) <0-255> ment for Text PPC 128 background (color) <0-255> processing Printed PPC 128 (background image (color) <0-255> density) Photo PPC 128 (color) <0-255> Map PPC 128 (color) <0-255> Manual offset- Text/Photo PPC 128 ting adjust(color) <0-255> ment for Text PPC 128 b
Adjustment mode (05) Default Func- Sharpness adjustment / PPC EUR: 0 Auto Color Mode (Text/ (color) UC: 0 Photo) JAPN: 22 <0-31> Code Classification 1757 Image 1761 Image Black reproduction switching PPC (color) 0 <0-1> SYS 1769 Image Setting for highlighter PPC (color) PPC (color) PPC (color) PPC (color) PPC (color) PPC (color) PPC (color) PPC (color) PPC (color) PPC (color) PPC (color) PPC (color) PPC (color) PPC (color) PPC (color) PPC (color) PPC (color) PPC (
Code Classification 1784-0 Image 1784-1 Items Color balance adjustment for M (Text/Photo) 1784-2 1785-0 Image 1785-1 Color balance adjustment for M (Text) 1785-2 1786-0 Image 1786-1 1786-2 1787-0 Image 1787-1 Color balance adjustment for M (Printed image) Color balance adjustment for M (Photo) 1787-2 1788-0 Image 1788-1 Color balance adjustment for M (Map) 1788-2 1789-0 Image 1789-1 Color balance adjustment for C (Text/Photo) 1789-2 1790-0 Image 1790-1 Color balance ad
Code Classification 1793-0 Image 1793-1 Items Color balance adjustment for C (Map) 1793-2 1794-0 Image 1794-1 Color balance adjustment for K (Text/Photo) 1794-2 1795-0 Image 1795-1 Color balance adjustment for K (Text) 1795-2 1796-0 Image 1796-1 1796-2 1797-0 Image 1797-1 Color balance adjustment for K (Printed image) Color balance adjustment for K (Photo) 1797-2 1798-0 Image 1798-1 Color balance adjustment for K (Map) 1798-2 1800-0 1800-1 Image control Upper limit valu
Code 1802-0 1802-1 Classification Image control Items Upper limit value of laser power 1802-2 1802-3 1803-0 1803-1 Image control Lower limit value of laser power 1803-2 1803-3 1804-0 1804-1 Image control Background voltage actual value display 1804-2 1804-3 1805-0 1805-1 Image control 1805-2 Drum surface potential characteristic/ slope factor display 1805-3 1806-0 Image control 1806-1 Drum surface potential characteristic/offset factor display 1806-2 1806-3 1807-0 1807-1 Image control 180
Code 1808-0 Classification Image control 1808-1 1808-2 Items Drum exposure voltage characteristic/ offset factor display (main charger grid low voltage area) 1808-3 1809-0 1809-1 Image control 1809-2 1809-3 1810-0 Image control 1810-1 1810-2 Drum exposure voltage characteristic/ slope factor display (main charger grid high voltage area) Drum exposure voltage characteristic/ offset factor display (main charger grid high voltage area) 1810-3 1811-0 1811-1 Image control Contrast voltage/upper limit
1817 Image control Adjustment mode (05) Default Func- Display of Y ALL 170 background <0-999> voltage/upper M ALL 170 limit actual <0-999> value C ALL 170 <0-999> K ALL 170 <0-999> Background Y ALL 80 voltage/lower <0-999> limit actual M ALL 80 value display <0-999> C ALL 80 <0-999> K ALL 80 <0-999> Contrast voltY ALL 0 age/correc<0-255> tion number of M ALL 0 time display <0-255> C ALL 0 <0-255> K ALL 0 <0-255> Laser power Y ALL 0 correction/ <0-255> number of M ALL 0 time d
Code Classification 1822-0 Transfer 1822-1 1822-2 1822-3 1822-4 1823-0 Transfer 1823-1 1823-2 1823-3 1825-0 Transfer 1825-1 1825-2 1825-3 1826-0 Transfer 1826-1 1827-0 Transfer 1827-1 1828-0 Transfer 1828-1 1829-0 1829-1 1829-2 Transfer Adjustment mode (05) Default Func- 2nd transfer Plain ALL 92 roller bias corpaper <0-255> rection of trailThick ALL 88 ing edge of paper 1 <0-255> paper Thick ALL 90 paper 2 <0-255> Thick ALL 90 paper 3 <0-255> OHP film ALL 90 <0
Code Classification 1831 Transfer 1832 Transfer 1833 Transfer 1836 Transfer 1839-0 Transfer 1839-1 1840-0 Transfer Adjustment mode (05) Default Func- 1st transfer roller bias ALL 187 actual value display at (black) <0-255> deceleration (Thick paper 2) 1st transfer roller bias ALL 187 actual value display at (black) <0-255> deceleration (Thick paper 3) 1st transfer roller bias ALL 187 actual value display at (black) <0-255> deceleration (OHP film) 1st transfer rol
Code Classification 1842-0 Transfer 1842-1 1842-2 1842-3 1845-0 Transfer 1845-1 Adjustment mode (05) Default Func- Actual value IntermediALL 153 display of 2nd ate level (black) <0-225> transfer roller bias of bias trailing of leading/ edge trailing Bias of ALL 157 edge of paper leading/ (black) <0-225> (Tab paper) trailing edge IntermediALL 150 ate level (color) <0-225> bias of trailing edge Bias of ALL 154 leading/ (color) <0-225> trailing edge 2nd transfer roller b
Code Classification 1862-0 Transfer 1862-1 1862-2 1862-3 1863 Transfer 1864 Transfer © June 2005 TOSHIBA TEC Adjustment mode (05) Default Func- 1st transfer Y ALL 138 roller bias (color) <0-225> RMS value M ALL 143 display (color) <0-225> C ALL 154 (color) <0-225> K ALL 154 (color) <0-225> 1st transfer roller bias ALL 5 resistance detection Cur<0-10> rent offset adjustment 1st transfer roller bias correction at low-speed color printing ALL (color) 100 <0-100> RAM
2.2.5 Setting mode (08) The items in the setting code list can be set or changed in this setting mode (08). When the power should be turned OFF, be sure to shut down the equipment by pressing the [ENERGY SAVER] button for a few seconds. Procedure 1 ÅÝßÒÝÛÔà ÅðÃÅèà ÅÐÑÉÛÎà ÅÜ·¹·¬¿´ µ»§Ã øݱ¼»÷ ÅÜ·¹·¬¿´ µ»§Ã öÅÚËÒÝÌ×ÑÒ ÝÔÛßÎà ͻ¬- ±® ½¸¿²¹»- ª¿´«» ÅÍÌßÎÌà ÅÛÒÌÛÎà ÅÐÑÉÛÎà ÑÚÚñÑÒ ±® øÛ¨·¬÷ Å×ÒÌÛÎÎËÐÌà øͬ±®»- ª¿´«» ·² ÎßÓ÷ ÅÝÔÛßÎà øݱ®®»½¬- ª¿´«»÷ * Press [FUNCTION CLEAR] to enter minus (-).
Procedure 5 ÅÝßÒÝÛÔà ÅðÃÅèà ÅÐÑÉÛÎà ÅÜ·¹·¬¿´ µ»§Ã øݱ¼»÷ ÅÜ·¹·¬¿´ µ»§Ã öÅØÛÔÐà ͻ¬- ±® ½¸¿²¹»- ª¿´«» ÅÍÌßÎÌà ÅÛÒÌÛÎà ÅÐÑÉÛÎà ÑÚÚñÑÒ ±® øÛ¨·¬÷ Å×ÒÌÛÎÎËÐÌà øͬ±®»- ª¿´«» ·² ÎßÓ÷ 2 * Press [HELP] to enter "-".
Procedure 11 and 12 ÅÝßÒÝÛÔà ÅðÃÅèà ÅÐÑÉÛÎà ÅÜ·¹·¬¿´ µ»§Ã øݱ¼»÷ ÅÜ·¹·¬¿´ µ»§Ã ±® ÅÛÒÌÛÎà ÅÍÌßÎÌà öîøͬ±®»- ª¿´«» ·² ÎßÓ÷ Åͱº¬©¿®» µ»§¾±¿®¼Ã öï ÅÓÑÒ×ÌÑÎñÐßËÍÛà ͻ¬- ±® ½¸¿²¹»- ª¿´«» ÅÝÔÛßÎà øݱ®®»½¬- ª¿´«»÷ ÅÐÑÉÛÎà ÑÚÚñÑÒ øÛ¨·¬÷ *1 Press [MONITOR/PAUSE] to enter "-", when entering telephone number. *2 The data are stored in SYS-RAM in procedure 11 and stored in NIC-RAM in procedure 12.
Notes: 1. The digit after the hyphen in Code of the following table is a sub code. 2. In RAM, the NVRAM of the board in which the data of each code is stored is indicated. M stands for the LGC board, SYS, NIC and UTY stands for the SYS board.
Code Classification Setting mode (08) Default Func- Auto Shut Off Mode timer ALL Refer to setting (Sleep Mode) content <0-20> 206 User interface 207 User interface Highlighting display on LCD 209 User interface 210 RAM Contents SYS Timer to enter the Sleep Mode automatically when the equipment has not been used 0: 3min. 1: 5min. 2: 10min. 3: 15min. 4: 20min. 5: 25min. 6: 30min. 7: 40min. 8: 50min. 9: 60min. 10: 70min. 11: 80min. 12: 90min. 13: 100min. 14: 110min.
Code 223 224 Classification Maintenance Setting mode (08) Default Func- Switching of output pages/ ALL 0 driving counts at PM <0-1> RAM Contents M Selects the reference to notify the PM timing. (The message is displayed on the LCD screen.) 0: PM counter (The number of output pages is set at 08251.) 1: PM time counter (The timing is set at 08-375.) Press the button on the LCD to select the size. Press the button on the LCD to select the size.
Code Classification 236 Paper feeding 237 Paper feeding 238 Paper feeding 239 Paper feeding 240 Paper feeding 241 Paper feeding 242 Paper feeding 243 Paper feeding 244 Paper feeding 245 Paper feeding 246 Paper feeding 247 Paper feeding 248 Paper feeding 249 Paper feeding Setting mode (08) Default Func- Paper size (LG) ALL 356/216 feeding/widthwise direction <182432/140297> Paper size (ST-R) ALL 216/140 feeding/widthwise direction <182432/140297> Pa
Code 250 Classification Maintenance Setting mode (08) Default Func- Service technician teleALL 0 phone number <32 digits> Contents SYS A telephone number can be entered up to 32 digits. Use the [MONITOR/PAUSE] button to enter a hyphen(-). e-STUDIO281c UC, EUR: 100,000 JPN: 0 e-STUDIO351c UC, EUR: 120,000 JPN: 0 e-STUDIO451c UC, EUR: 150,000 JPN: 0 Counts up when the registration sensor is ON.
Code Classification Items Setting mode (08) Default Func- ALL 1 <0-2> Contents SYS SYS Sets whether the FSMS connection is accepted or not. 0: Prohibited 1: Accepted (serial connection only) 2: Accepted (both serial and USB connections) 0: No limits 1 to 30: 1 to 30 days 31: 1 hour 32: 2 hours 33: 4 hours 34: 8 hours 35: 12 hours When a certain period of time has passed without operation after accessing TopAccess, the data being registered is automatically reset.
Code 268 Classification User interface Setting mode (08) Default Func- Binarizing level selection ALL 3 (When judging as black in <1-5> the ACS Mode) RAM SYS 270 Electronic filing Default setting of user box retention period ALL 0 <0-999> SYS 271 General Warning notification of the File Share and e-Filling partitions are filled ALL 90 <0-100> SYS 272 Scanning Notification setting of Email saving time limit ALL 3 <0-99> SYS 273 Scanning Default setting of p
Code Classification Setting mode (08) Default Func- Default setting of density SCN 0 adjustment (Black) (black) <0-11> RAM 276 User interface 277 User interface Default setting of background adjustment (Full Color) SCN (color) 3 <1-5> SYS 278 User interface Default setting of color mode SCN 0 <0-4> SYS 279 User interface Default setting of resolution (Full Color) SCN (color) 2 <0-3> SYS 280 User interface Default setting of resolution (Gray Scale) SCN
Code 286 Classification User interface Setting mode (08) Default Func- Default setting of original ALL 0 paper size <0-22> RAM Contents SYS 0: Automatic 1: A3 2: A4 3: LD 4: LT 5: A4-R 6: A5-R 7: LT-R 8: LG 9: B4 10: B5 11: ST-R 12: COMP 13: B5-R 14: FOLIO 15: 13"LG 16: 8.5"x 8.5" 18: A6-R 19: Size mixed 20: 8K 21: 16K 22: 16K-R Sets the search interval of deleting expired files and checking capacity of HDD partitions.
Setting mode (08) Default Func- PRT 1200 <50012800> Code Classification 296 Network Raw printing job (Number of form lines) 297 Network Raw printing job (PCL font pitch) PRT 1000 <449999> SYS 298 Network Raw printing job (PCL font size) PRT 1200 <40099975> SYS 299 Network PRT User interface Counter 0 <0-79> 0 <0-2> 0 <8 digits> SYS 300 Raw printing job (PCL font number) Maximum number of copy volume (MAX9) Number of A3 output pages A4 at Full Color A5 Mode in
Code 303-0 303-1 303-2 303-3 303-4 303-5 303-6 303-7 303-8 303-9 303-10 303-11 303-12 303-13 303-14 303-15 303-16 304-0 304-1 304-2 304-3 304-4 304-5 304-6 304-7 304-8 304-9 304-10 304-11 304-12 304-13 304-14 304-15 304-16 Classification Counter Counter © June 2005 TOSHIBA TEC Items Number of output pages at Full Color Mode in Printer Function Number of output pages at Twin Color Mode in Copier Function Setting mode (08) Default Func- PRT 0 (color) <8 digits> A3 A4 A5 A6 B4 B5
Code 305-0 305-1 305-2 305-3 305-4 305-5 305-6 305-7 305-8 305-9 305-10 305-11 305-12 305-13 305-14 305-15 305-16 306-0 306-1 306-2 306-3 306-4 306-5 306-6 306-7 306-8 306-9 306-10 306-11 306-12 306-13 306-14 306-15 306-16 Classification Items Counter Number of output pages at Black Mode in Copier Function Counter Number of output pages at Black Mode in Printer Function Setting mode (08) Default Func- PPC 0 (black) <8 digits> A3 A4 A5 A6 B4 B5 FOLIO LD LG LT ST COMP 13LG 8.
Code 307-0 307-1 307-2 307-3 307-4 307-5 307-6 307-7 307-8 307-9 307-10 307-11 307-12 307-13 307-14 307-15 307-16 308-0 308-1 308-2 308-3 308-4 308-5 308-6 308-7 308-8 308-9 308-10 308-11 308-12 308-13 308-14 308-15 308-16 Classification Counter Counter © June 2005 TOSHIBA TEC Items Number of output pages at List Print Mode Number of output pages in FAX Function Setting mode (08) Default Func- PRT 0 (black) <8 digits> A3 A4 A5 A6 B4 B5 FOLIO LD LG LT ST COMP 13LG 8.5 x 8.
Code 309-0 309-1 309-2 309-3 309-4 309-5 309-6 309-7 309-8 309-9 309-10 309-11 309-12 309-13 309-14 309-15 309-16 310-0 310-1 310-2 310-3 310-4 310-5 310-6 310-7 310-8 310-9 310-10 310-11 310-12 310-13 310-14 310-15 310-16 Classification Items Counter Number of scanning pages at Full Color Mode in Copier Function Counter Number of scanning pages at Full Color Mode in Scanning Function Setting mode (08) Default Func- PPC 0 (color) <8 digits> A3 A4 A5 A6 B4 B5 FOLIO LD LG LT ST
Code 311-0 311-1 311-2 311-3 311-4 311-5 311-6 311-7 311-8 311-9 311-10 311-11 311-12 311-13 311-14 311-15 311-16 312-0 312-1 312-2 312-3 312-4 312-5 312-6 312-7 312-8 312-9 312-10 312-11 312-12 312-13 312-14 312-15 312-16 Classification Counter Counter © June 2005 TOSHIBA TEC Items Number of scanning pages at Twin Color Mode in Copier Function Number of scanning pages at Black Mode in Copier Function Setting mode (08) Default Func- PPC 0 (color) <8 digits> A3 A4 A5 A6 B4 B5 F
Code 313-0 313-1 313-2 313-3 313-4 313-5 313-6 313-7 313-8 313-9 313-10 313-11 313-12 313-13 313-14 313-15 313-16 314-0 314-1 314-2 314-3 314-4 314-5 314-6 314-7 314-8 314-9 314-10 314-11 314-12 314-13 314-14 314-15 314-16 Classification Items Counter Number of scanning pages in Scanning Function Counter Number of scanning pages in FAX Function Setting mode (08) Default Func- SCN 0 (black) <8 digits> A3 A4 A5 A6 B4 B5 FOLIO LD LG LT ST COMP 13LG 8.5 x 8.
Code 315-0 315-1 315-2 315-3 315-4 315-5 315-6 315-7 315-8 315-9 315-10 315-11 315-12 315-13 315-14 315-15 315-16 316-0 316-1 316-2 316-3 316-4 316-5 316-6 316-7 316-8 316-9 316-10 316-11 316-12 316-13 316-14 316-15 316-16 Classification Counter Counter © June 2005 TOSHIBA TEC Items Number of transmitted pages in FAX Function Number of received pages in FAX Function Setting mode (08) Default Func- FAX 0 <8 digits> A3 A4 A5 A6 B4 B5 FOLIO LD LG LT ST COMP 13LG 8.5 x 8.
Code Classification 317-0 Counter 317-1 Counter 317-2 Counter 318-0 Counter 318-1 Counter 318-2 Counter 319-0 Counter 319-1 Counter 319-2 Counter Items Display of number of output pages at Full Color Mode in Copier Function Large Display of number of output pages at Full Color Mode in Printer Function Large Display of number of output pages at Twin Color Mode in Copier Function Large Small Total Small Total Small Total Setting mode (08) Default Func- PPC
Code Classification 320-0 Counter 320-1 Counter 320-2 Counter 321-0 Counter 321-1 Counter 321-2 Counter 322-0 Counter 322-1 Counter 322-2 Counter © June 2005 TOSHIBA TEC Items Display of number of output pages at Black Mode in Copier Function Large Display of number of output pages at Black Mode in Printer Function Large Display of number of output pages at List Print Mode Large Small Total Small Total Small Total Setting mode (08) Default Func- PPC 0 (b
Code Classification 323-0 Counter 323-1 Counter 323-2 Counter 324-0 Counter 324-1 Counter 324-2 Counter 325-0 Counter 325-1 Counter 325-2 Counter Items Display of number of output pages in FAX Function Large Small Total Display of number of scanning pages at Full Color Mode in Copier Function Large Display of number of scanning pages at Full Color Mode in Scanning Function Large Small Total Small Total Setting mode (08) Default Func- FAX 0 <8 digits> FAX 0
Code Classification 326-0 Counter 326-1 Counter 326-2 Counter 327-0 Counter 327-1 Counter 327-2 Counter 328-0 Counter 328-1 Counter 328-2 Counter © June 2005 TOSHIBA TEC Items Setting mode (08) Default Func- PPC 0 (color) <8 digits> PPC 0 (color) <8 digits> PPC 0 (color) <8 digits> Display of number of scanning pages at Twin Color Mode in Copier Function Large Display of number of scanning pages at Black Mode in Copier Function Large Display of number of sc
Code Classification 329-0 Counter 329-1 Counter 329-2 Counter 330-0 Counter 330-1 Counter 330-2 Counter 331 User interface Items Display of number of scanning pages in Scanning Function Display of number of transmitted pages in FAX Function Large Small Total Setting mode (08) Default Func- SCN 0 (black) <8 digits> SCN 0 (black) <8 digits> SCN 0 (black) <8 digits> Large FAX Small FAX Total FAX Default setting of screen ALL e-STUDIO281c/351c/451c ERROR CODE
Code Classification 332-0 Counter 332-1 Counter 332-2 Counter 333-0 Counter 333-1 Counter 333-2 Counter 334-0 Counter 334-1 Counter 334-2 Counter 335-0 Counter 335-1 Counter 335-2 Counter 342 User interface Displaying number of original pages placed on original glass 343 User interface 344 Counter 346 Counter 347 Counter © June 2005 TOSHIBA TEC Items Display of number of received pages in FAX Function Large Display of total number of pages at Full Color Mode Large S
Code Classification 348 Counter 349 Counter 352 Counter 353 Counter 356 Counter 357 Setting mode (08) Default Func- Count setting of thick paper ALL 1 (PM) <0-1> Count setting of OHP film ALL 1 (PM) <0-1> Count setting of largeALL JPN: 0 sized paper (Fee charging OTHER: system counter) 1 <0-2> RAM M M M Definition setting of largesized paper (Fee charging system counter) Counter for upper drawer feeding ALL 0 <0-1> M ALL 0 <8 digits> M Counter Counter for
Setting mode (08) Default Func- Number of errors in HDD PPC 0 (Copying) <8 digits> Number of errors in HDD FAX 0 (FAX) <8 digits> Number of errors in HDD SCN 0 (Scanning) <8 digits> Number of errors in HDD PRT 0 (Printer) <8 digits> Number of polygonal motor ALL 0 rotational speed switching <8 digits> Code Classification 390 Counter 391 Counter 392 Counter 393 Counter 398 Laser 399 Laser Accumulated time of polygonal motor at normal rotation ALL 0 <8 digits> M
Code Classification 411 Fuser 412-0 Fuser 412-1 413-0 Fuser 413-1 415-0 Fuser 415-1 Setting mode (08) Default Func- Fuser roller temperature on ALL 12 standby (Center ther<0-16> mistor) RAM Contents M 0: 120°C 1: 125°C 2: 130°C 3: 135°C 4: 140°C 5: 145°C 6: 150°C 7: 155°C 8: 160°C 9: 165°C 10: 170°C 11: 175°C 12: 180°C 13: 185°C 14: 190°C 15: 195°C 16: 200°C 0: 120°C 1: 125°C 2: 130°C 3: 135°C 4: 140°C 5: 145°C 6: 150°C 7: 155°C 8: 160°C 9: 165°C 10: 170°C 11:
Code Classification 428-0 Fuser 428-1 430 Fuser 431 432 436 Fuser 437-0 Fuser 437-1 438-0 Fuser Setting mode (08) Default Func- Period of time retaining 3 ALL print-start temperature <0-10> (black) (Thick paper 2) 2 ALL <0-10> (color) Transport motor speed deceleration (OHP film) Transport motor speed deceleration (Thick paper 2) Transport motor speed deceleration (Thick paper 3) Temperature setting to start solving abnormality(Center/Side thermistor/ Thick paper2)
Code Classification 440-0 Fuser Setting mode (08) Default Func- Pre-running time for first ALL 12 printing (black) <0-16> (Plain paper/Low temperature environment) 440-1 441-0 Fuser Pre-running time for first printing (Thick paper 1) 441-1 449 RAM Contents M 0: Invalid 1: 0 sec. 2: 2 sec. 3: 3 sec. 4: 4 sec. 5: 5 sec. 6: 6 sec. 7: 7 sec. 8: 8 sec. 9: 10 sec. 10: 12 sec. 11: 14 sec. 12: 16 sec. 13: 18 sec. 14: 20 sec. 15: 25 sec. 16: 30 sec. 0: Invalid 1: 0 sec.
Code Classification 462 RADF 463-0 463-1 Paper feeding © June 2005 TOSHIBA TEC Setting mode (08) Default Func- Setting for switchback ALL 0 operation in mixed-size <0-2> copying using RADF Feeding retry number setting (upper drawer) Plain paper Others ALL ALL 5 <0-5> 5 <0-5> RAM Contents SYS This setting is whether the original length is detected or not by transporting without scanning in reverse when A4-R/FOLIO paper or LT-R/LG paper is detected in a mixedsize c
Code 464-0 464-1 465-0 465-1 466-0 466-1 467-0 467-1 468-0 468-1 Classification Paper feeding Paper feeding Paper feeding Paper feeding Paper feeding 470 Paper feeding 471 Paper feeding 478 Laser 479 Laser 480 Paper feeding Setting mode (08) Default Func- Feeding retry Plain ALL 5 number setpaper <0-5> ting (lower Others ALL 5 drawer) <0-5> Feeding retry Plain ALL 5 number setpaper <0-5> ting (PFP Others ALL 5 upper drawer) <0-5> Feeding retry Plain ALL 5 number set
Code 481 482 Classification Paper feeding Setting mode (08) Default Func- Automatic change of paper PPC 1 source <0-2> ALL Pre-running rotation of polygonal motor ALL 0 <0-1> 0 <0-2> Contents SYS Sets whether or not changing the drawer automatically to the other drawer with the paper of the same size when paper in the selected drawer has run out. 0: OFF 1: ON (Changes to the drawer with the same paper direction and size: ex.
Setting mode (08) Default Func- Timing of auto-clearing of ALL 0 polygonal motor pre-run<0-2> ning rotation Code Classification 486 Laser 487 Transfer Selection of performing the 2nd transfer roller cleaning (Bypass feed) ALL 0 <0-1> M 488 Laser Setting of polygonal motor type ALL 3 <2-3> M 489 Laser Polygonal motor rotation number on standby ALL 5 <0-5> M 490 Laser ALL General ALL (color) 0 <0-1> 0 <0-1> M 497 Polygonal motor rotation in the ener
Code 544 Classification Image control Setting mode (08) Default Func- Environment correction ALL 1 control of 2nd transfer <0-1> roller bias RAM Contents M Sets whether or not correcting the 2nd transfer roller bias depending on the environment. 0: Invalid 1: Valid Sets whether or not correcting the 2nd transfer roller bias depending on the transfer belt life.
Code Classification Setting mode (08) Default Func- Drum temperature correcALL 1 tion control <0-1> RAM Contents M Sets whether or not correcting the drum voltage depending on the drum surface temperature in open-loop control. 0: Invalid 1: Valid Sets whether or not deciding the initial value of contrast voltage in open-loop control.
Setting mode (08) Default Func- Process switching for PPC 0 image smoothing (Photo) (black) <0-1> Code Classification 561 Image 562 Image Process switching for image smoothing (Text) PPC (black) 1 <0-1> M 565 Image control Image quality closed-loop control automatic start-up/ Relative humidity variation ALL (color) 1 <0-2> M 566 Image control Image quality closed-loop control automatic start-up/ Period of time unattended ALL (color) 1 <0-2> M 567 Image c
Code Classification Setting mode (08) Default Func- Image quality closed-loop ALL 8 control automatic start-up/ (color) <0-20> Temperature setting of fuser roller at power-ON RAM Contents M Sets the fuser roller temperature to perform closed-loop control when 1 or 2 (valid) is set in 08-559.
Code Classification 583-0 Fuser 583-1 583-2 Setting mode (08) Default Func- Pre-running Transport ALL 1 time at power- motor <0-10> ON and ready speed 1/1 status Transport ALL 4 motor <0-10> speed 1/2 Transport ALL 7 motor <0-10> speed 1/3 Transport motor speed of ALL 0 pre-running at ready status <0-2> RAM M M Fuser 585 User interface Default setting of Original mode PPC (color) 0 <0-4> SYS 586 Image Image quality switching when selecting the Image Smoothing Mo
Code Classification Items Setting mode (08) Default Func- ALL 0 <0-3> Contents SYS 0: Invalid 1: Single-sided to duplex copying 2: Two-sided to duplex copying 3: User selection 0: APS (Automatic Paper Selection) 1: AMS (Automatic Magnification Selection) 2: Not selected 0: Invalid 1: Valid 1 0: Continuous feeding (by pressing the [START] button) 1: Single feeding (by setting original on the tray) Sets the binarizing level of each step.
Code Classification 615 General Setting mode (08) Default Func- Size information of main ALL memory and page memory RAM Contents SYS Displays the sizes of the main memory and page memory. Enables to check if each memory is properly recognized. Sets the counting method in Twin Color Mode with the Limitation Function.
Code 633 634 636 638 Setting mode (08) Default ClassifiFunc- Data Releasing F200 service ALL 0 overwrite call <0-2> kit User Inner receiving tray priority ALL 0 interface at Non-sort Mode <0-1> User Width setting for image PPC 0 interface shift copying (linkage of <0-1> front side and back side) General Time differences ALL EUR: 24 UC: 40 JPN: 6 <0-47> 640 User interface Date display format ALL 641 User interface Automatic Sorting Mode setting (RADF) PPC 642 U
Code 645 Classification User interface Setting mode (08) Default Func- Correction of reproduction PPC 10 ratio in editing copy <0-10> RAM Contents SYS Sets the reproduction ratio for the X in 1 printing (including magazine sort) to the Reproduction ratio x Correction ratio. 0: 90% 1: 91% 2: 92% 3: 93% 4: 94% 5: 95% 6: 96% 7: 97% 8: 98% 9: 99% 10: 100% Sets the page pasted position for X in 1 to the upper left corner/ center.
Code Classification Items Setting mode (08) Default Func- PRT 0 <0-1> RAM Contents SYS Sets whether or not feeding a paper automatically into the copier when it is placed on the bypass tray. 0: OFF (Press the [START] button to start feeding.) 1: ON (Automatical feeding) Sets whether or not feeding a paper automatically into the copier when it is placed on the bypass tray. 0: OFF (Press the [START] button to start feeding.
Code Classification 672 General 675-0 Paper feeding Setting mode (08) Default Func- Initialization of department management information Coated Paper Mode setting for paper source RAM Contents SYS Initializing of the department management information * Enter the code with the digital keys and press the [INITIALIZE] button to perform the initialization.
Code Classification 676 Paper feeding 677-0 Paper feeding Setting mode (08) Default Func- Bypass copy printing PPC 0 [COATED] button display <0-1> Coated Paper Mode setting at bypass feeding RAM Contents SYS Sets whether or not displaying the [COATED] button on the LCD screen at bypass feeding. 0: Not displayed 1: Displayed (The Coated Paper Mode is applied by pressing the [COATED] button at bypass feeding.
Code Classification 678 General 679 General 680 General 681 General 682 Setting mode (08) Default Func- Setting of banner advertisALL 0 ing display <0-1> RAM Contents SYS Sets whether or not displaying the banner advertising. The setting contents of 08-679 and 08-680 are displayed at the time display section on the right top of the screen. When both are set, each content is displayed alternately.
Code Classification Setting mode (08) Default Func- Performing panel calibraALL tion Contents SYS Performs the calibration of the pressing position on the touch panel (LCD screen). The calibration is performed by pressing 2 reference positions after this code is started up. Returns the value to the factory shipping default value. Checks the bad sector. 0: Not installed 1: Installed 1 Sets the paper type priority during copying.
Code Classification 702 Maintenance 703 Maintenance 704-0 704-1 707 710 711 715 Maintenance Maintenance Maintenance Maintenance 717 Maintenance 718 Maintenance 719 Maintenance Maintenance 721 Maintenance 723 Maintenance Maintenance 726 © June 2005 TOSHIBA TEC RAM Contents SYS 0: Valid (Remote-controlled server) 1: Valid (L2) 2: Invalid Maximum 256 Bytes Remote-controlled service HTTP server URL setting Interruption of Copying stapling operation (no staple) Printing / BOX printin
727 Maintenance Setting mode (08) Default Func- HTTP proxy IP address ALL setting 728 Maintenance HTTP proxy port number setting ALL 729 Maintenance Maintenance Maintenance Maintenance (Remote) HTTP proxy ID setting HTTP proxy password setting HTTP proxy panel display Code 730 731 732 733 734 738 739 740 741 742 743 744 745 746 747 Classification Maintenance (Remote) Maintenance (Remote) Maintenance (Remote) Maintenance (Remote) Maintenance (Remote) Maintenance
Code 748 749 750 751 752 753 754 755 756 757 758 759 760 761 762 763 764 765 Classification Maintenance (Remote) Maintenance (Remote) Maintenance (Remote) Maintenance (Remote) Maintenance (Remote) Maintenance (Remote) Maintenance (Remote) Maintenance (Remote) Maintenance (Remote) Maintenance (Remote) Maintenance (Remote) Maintenance (Remote) Maintenance (Remote) Maintenance (Remote) Maintenance (Remote) Maintenance (Remote) Maintenance (Remote) Maintenance (Remote) © June 2005 TOSHIBA TEC Setting mode (0
Code Classification 767 Maintenance (Remote) 768 Maintenance (Remote) Maintenance (Remote) Maintenance (Remote) Maintenance (Remote) Maintenance 769 770 771 772 Setting mode (08) Default Func- Service Notification setting ALL 0 <0-2> RAM SYS Contents Enables to set up to 3 E-mail addresses to be sent.
Code 784 785 786 787 788 789 790 791 792 793 794 795 796 797 816 817 818 819-0 819-1 819-2 Setting mode (08) Default ClassifiFunc- Mainte- Remote-controlled service ALL 0 nance polling day selection Sun<0-1> day Mainte- Remote-controlled service ALL 0 nance polling day selection Mon<0-1> day Mainte- Remote-controlled service ALL 0 nance polling day selection Tues<0-1> day Mainte- Remote-controlled service ALL 0 nance polling day selection <0-1> Wednesday Mainte- Remote
Code 820-0 820-1 820-2 821 822-0 822-1 822-2 823-0 823-1 Setting mode (08) Default ClassifiFunc- Develop- Color autoY ALL ment toner sensor (color) <0-1023> output M ALL display for (color) <0-1023> developer C ALL material (color) <0-1023> Develop- ON/OFF of the mode for ALL 0 ment developer material stabili(color) <0-1> zation Develop- Number of ment times the mode for developer material stabilization is performed Develop- Color automent toner sensor/ light amount c
Code 859-0 859-1 859-2 860-0 860-1 861-0 861-1 862-0 862-1 863-0 863-1 864 865 866-0 866-1 867 Setting mode (08) Default ClassifiFunc- Develop- Toner empty Y ALL 0 ment detection (color) <0-1> M ALL 0 (color) <0-1> C ALL 0 (color) <0-1> Develop- Color autoUpper limit ALL 20 ment toner sensor/ (color) <0-1023> proper range Lower limit ALL 0 setting of OFF (color) <0-1023> level voltage Develop- Color autoUpper limit ment toner sensor/ proper range setting of Lower
Code Classification Setting mode (08) Default Func- Color auto-toner adjustALL 4 ment finishing range set(color) <0-255> ting RAM Contents M Sets the difference from the target value for judging whether the color auto-toner adjustment finishes correctly or not. Sets the difference from the target value for judging whether the light amount correction finishes correctly or not.
Code 876-0 876-1 Classification Items Develop- Color develment oper life correction value (segment 1) 876-2 877-0 877-1 878-1 Develop- Color develment oper life correction value (segment 2) 879-1 Develop- Color develment oper life correction value (segment 3) 880-1 Develop- Color develment oper life correction value (segment 4) 881-1 Y M Y M C Develop- Color develment oper life correction value (segment 5) 880-2 881-0 M C 879-2 880-0 Y C 878-2 879-0 M C 877-2 878-0 Y Y M C Develop-
Code Classification 900 Version 903 905 907 908 911 Version Version Version Version Version 915 920 Version Version 921 922 Version Version 923 Version 924 Version 925 Version 926 Version 927 Version 928 Version 929 Version 930 Version 931 Version 933 934 Version Version 935 Version 936 Version 937 Version 938 Version 939 Version 944 Version 945 Network Setting mode (08) Default Func- System firmware ROM verALL sion Engine ROM version
Setting mode (08) Default Func- Initialization after software ALL version upgrade Code Classification 947 General 949 General Automatic interruption page setting during black printing ALL 0 <0-100> SYS 950 Electronic filing Start-up method of Electronic Filing ALL 0 <0-2> SYS 951 User interface Image setting for Electronic Filing printing (Only for color image) ALL 0 <0-3> SYS 953 User interface Access code entry for Electronic Filing printing ALL 0 <
Setting mode (08) Default Func- Raw printing job PRT 0 (Paper feeding drawer) <0-5> Code Classification 978 Network 979 Network Raw printing job (PCL symbol set) PRT 0 <0-39> SYS 983 User interface General JOB STATUS initial screen setting Copy function setting ALL 0 <0-1> 0 <0-1> SYS 986 PPC e-STUDIO281c/351c/451c ERROR CODE AND SELF-DIAGNOSTIC MODE 2 - 146 06/08 RAM SYS SYS Contents 0: 1: 2: 3: 4: 5: 0: 1: 2: 3: 4: AUTO Upper drawer Lower drawer PFP up
Code Classification Items Setting mode (08) Default Func- ALL 0 <0-2> RAM Contents SYS 0: Not switched 1: LG 13"LG 2: FOLIO 13"LG This code can be also keyed in from the adjustment mode (05976). 10 digits Refer to values of total counter.
Setting mode (08) Default Func- IP address to DNS server ALL (Primary) Code Classification 1018 Network 1019 Network IP address to DNS server (Secondary) ALL - NIC 1020 Network DDNS Desired level ALL 1 <1-5> NIC 1022 Network From Name Creation setting in SMTP authentication ALL 0 <0-1> SYS 1023 Network NetBios name ALL MFP_ serial UTY 1024 Network Name of WINS server or IP address (Primary) ALL - UTY 1025 Network Name of WINS server or IP ad
Setting mode (08) Default Func- E-mail box name to SMTP ALL server Availability of Offramp ALL 2 <1-2> Offramp security ALL 1 <1-2> Printing at Offramp ALL 1 <1-2> Availability of POP3 clients ALL 1 <1-2> FQDN or IP address to ALL POP3 server Types of POP3 server ALL 1 <1-3> Code Classification 1042 Network 1043 Network 1044 Network 1045 Network 1046 Network 1047 Network 1048 Network 1049 Network 1050 1051 Network Network 1052 Network TCP port number of P
Code Classification 1079 Network 1080 Network 1081 Network 1082 1083 1084 Network Network Network 1085 Network 1086 Network 1087 Network 1088 Network 1089 Network 1090 1091 Network Network 1092 Network 1093 Setting mode (08) Default Func- Availability of IPP port ALL 1 number 80 <1-2> TCP port number of IPP ALL 631 <165535> IPP printer name ALL MFP_ serial IPP printer location IPP printer information IPP printer information (more) Installer of IPP pr
Code Classification 1100 Network Setting mode (08) Default Func- Method of SMTP server ALL 1 authentication <1-7,10> RAM Procedur e ALL - NIC ALL - NIC Maximum 64 letters 12 Network Login name for SMTP server authentication Login password for SMTP server authentication Rendezvous setting 1: Disable 2: Plain 3: Login 4; Cram-MD5 5: Digest MD5 6: Kerberos 7: NTLM 10: Auto Maximum 64 letters ALL NIC Network Link local host name ALL 1105 Network Service nam
Setting mode (08) Default Func- Windows domain of device ALL 4 authentication <3-4> Code Classification 1123 Network 1124 Network Workgroup name ALL 1125 General ALL 1126 Counter 1128 Network 1129 Network 1130 User interface Data writing of address book data import (overwriting method) Validity of interrupt copying when external counters are installed NetwareUserAuthTree Name1 NetwareUserAuthContext Name1 Job Build Function 1131 User interface 1132 RAM U
Code Classification 1141 Network Setting mode (08) Default Func- Display of MAC address ALL - Procedur e RAM Contents SYS 12 NetwareUserAuthContext Name2 NetwareUserAuthTree Name3 Counter notification Remote FAX setting ALL - UTY (**:**:**:**:**:**) The address is displayed as above (6-byte data is divided by a colon at every 2 bytes).
Code Classification Setting mode (08) Default Func- Fuser roller energy saving ALL 0 temperature time accumu<8 digits> lating counter Display/0 clearing RAM Contents M Counts up the heater control time accumulated (at energy saving mode). When the counter value of the fuser belt is cleared, this counter value is also cleared in sync at PM support mode. Counts up when the registration sensor is ON.
Code Classification Items Setting mode (08) Default Func- ALL 0 <8 digits> RAM Contents M Counts the number of times of the feeding retry from the PFP lower drawer. Counts the number of times of the feeding retry from the bypass tray. Counts the number of times of the feeding retry from the LCF. When the number of feeding retry (08-1390 to 08-1395) exceeds the setting value, the feeding retry will not be performed subsequently.
Code Classification Setting mode (08) Default Func- HDD data overwriting type ALL 0 setting <0-2> RAM Contents SYS Select the type of the overwriting level; LOW, MEDIUM, or HIGH for deleting HDD data. (This setting is enabled only when the GP-1060 is installed.) 0: LOW 1: MEDIUM 2: HIGH Select the type of the overwriting level; LOW, MEDIUM, or HIGH for deleting HDD data. (This setting is enabled only when the GP-1060 is installed.
Code Classification 1435 Network Setting mode (08) Default Func- "Disable private and proof ALL 0 print save" function <0-1> RAM SYS 1436 Network "Disable fax save" function ALL 0 <0-1> SYS 1440 Network IP Conflict Detect ALL 1 <1-2> - 1441 Network SNTP Enable ALL 2 <1-2> - 1442 Network SNTP Polling rate ALL - 1444 Network Primary SNTP Address ALL 24 <1-168> - - 1445 Network Secondary SNTP Address ALL - - 1446 Network Port number to SN
Code Classification 1469 General 1470 General 1471 General 1472 General 1473 General 1474 General 1476 Network 1477 Setting mode (08) Default Func- User data management ALL 0 limitation Setting by num(color) <7 digits> ber of printouts Device authentication funcALL 0 tion setting <0-1> User authentication ALL 0 method <0-5> RAM 0-9,999,999: 0-9,999,999 sheets 1 SYS 0: 1: 0: 1: 2: 3: OFF ON Local NTLM (NT Domain) LDAP Kerberos (Active Directory) 4: Netware
Code Classification 1484 Network 1485 Network 1487 Network 1489 Network 1491 Network 1492 Paper feeding 1493 Network 1494 1495 Setting mode (08) Default Func- Authentication method of ALL 0 "Scan to Email" <0-2> RAM SYS Setting whether use of the Internet FAX is permitted at the time of authentication "From" address assignment method at the time of authentication ALL 0 <0-1> SYS ALL 0 <0-2> SYS Setting for "From" address edit at "Scan to Email" E-mail
Setting mode (08) Default Func- Operation setting for User ALL 1 authentication/registration <0-1> Code Classification 1496 General 1497 Elece-Filing Access Mode (for tronic Fil- Client) ing FAX Inbound FAX function (Forwarding by TSI) 1498 1530-0 Number of output pages in black mode Contents SYS 0 : Disables operation setting for User authentication/registration 1 : Enables operation setting for User authentication/registration 0: Mode 1 1: Mode 2 2: Mode 3 0: OFF
Code Classification 1531-0 Counter 1531-1 Setting mode (08) Default Func- Number of 1-UP / PPC 0 output pages Duplex (color) <8 digits> in full color printing mode 2-UP / PPC 0 Duplex (color) <8 digits> printing RAM Contents SYS Counts the number of output pages printed only in the full color mode. Counts the number of output pages printed in the full color mode using [2IN1] or [MAGAZINE SORT].
Code Classification 1533-0 Counter 1533-1 Setting mode (08) Default Func- Number of 1-UP / PRT 0 output pages Duplex (black) <8 digits> of the printer printing or BOX 2-UP / PRT 0 Duplex (black) <8 digits> printing RAM Contents SYS Counts the number of output pages printed in the black mode. Counts the number of output pages printed in the black mode using [2IN1] or [MAGAZINE SORT]. * When printing is performed using a Windows driver, the 1-UP image will be output.
Code Classification 1534-0 Counter 1534-1 Setting mode (08) Default Func- Number of 1-UP / PRT 0 output pages Duplex (color) <8 digits> of the printer printing or BOX (Full color) 2-UP / PRT 0 Duplex (color) <8 digits> printing Contents SYS Counts the number of output pages printed only in the full color mode. Counts the number of output pages printed in the full color mode using [2IN1] or [MAGAZINE SORT].
Code 1666 1667 1668 1669 1670 1671 1672 1673 1674 1675 1676 1677 1678 1679 Classification Wireless LAN Wireless LAN Wireless LAN Wireless LAN Wireless LAN Wireless LAN Wireless LAN Wireless LAN Wireless LAN Wireless LAN Wireless LAN Wireless LAN Wireless LAN Wireless LAN Setting mode (08) Default Func- Wireless LAN driver ALL 1 Transmission rate <1-2> Wireless LAN driver ALL 1 Transmission rate value <1-12> Wireless LAN driver Operation channel Wireless LAN driver Operatio
1686 Wireless LAN Setting mode (08) Default Func- Wireless LAN supplicant ALL EAP user name 1689 Wireless LAN Wireless LAN supplicant Authentication interval ALL 30 <3065535> - 1690 Wireless LAN Wireless LAN supplicant Holding interval ALL 60 <6065535> M 1691 Wireless LAN Wireless LAN supplicant EAPOL-Start Number of times of packet retry ALL 3 <165535> M 1692 Wireless LAN Wireless LAN supplicant Session resume ALL 2 <1-2> - 1693 Wireless LAN Wirele
Code 1701 1704 Classification Wireless LAN Wireless LAN Setting mode (08) Default Func- Wireless LAN supplicant ALL 1 CN name check <1-2> Wireless LAN supplicant ALL 0 Update interval of PTK <0-720> (Pairwise Transient Key) RAM 1: NO - The update interval of a secret key across AP (Access Point) and STA (Station) can be set. This interval is for updating the secret key from STA.
Code 1715 Classification Bluetooth 1719 Bluetooth 1720 Items Bluetooth Data encryption Setting mode (08) Default Func- ALL 1 <0-1> RAM Contents SYS 0: Not encrypted 1: Encrypted This setting is valid only when the bluetooth security function is ON. 0: Fit page 1: 1/2 size 2: 1/4 size 3: 1/8 size IP filter minimum area 1 000.000.000.000255.255.255.255 (Default value: 000.000.000.000) IP filter maximum area 1 000.000.000.000255.255.255.255 (Default value: 000.000.000.
Setting mode (08) Default Func- IP address range for IP filALL ter (Maximum area 5) Code Classification 1729 Network 1730 Network IP address range for IP filter (Minimum area 6) ALL - - 1731 Network IP address range for IP filter (Maximum area 6) ALL - - 1732 Network IP address range for IP filter (Minimum area 7) ALL - - 1733 Network IP address range for IP filter (Maximum area 7) ALL - - 1734 Network IP address range for IP filter (Minimum area
Code Classification 1739 Network 1740 Network 1741 Network 1742 Network 1743 Network 1744 Setting mode (08) Default Func- IP address range for IP filALL ter (Maximum area 10) SSL setting SSL ftp server OFF/ON SSL setting HTTP server port number ALL SSL setting IPP server OFF/ON setting SSL setting IPP server port number ALL Network SSL setting SSL ftp server OFF/ON ALL 1745 Network SSL setting SSL ftp server Port ALL 1746 Network SSL setting SSL LDAP
Setting mode (08) Default Func- Enabling server's IP ALL 2 address acquired by DHCP <1-2> Code Classification 1755 Network 1756 Network Enabling server's IP address acquired by DHCP ALL 2 <1-2> - 1757 Network Enabling server's IP address acquired by DHCP ALL 1 <1-2> - 1762 Network Enabling server's IP address acquired by DHCP ALL 2 <1-2> - 1764 Wireless LAN ALL - 1765 Wireless LAN ALL 1766 Wireless LAN 1767 Network Wireless LAN supplicant Contr
Code Classification 1778 General Setting mode (08) Default Func- Hang-up period of control ALL 1 panel at the 3rd misentry of <0-7> administrator's password RAM Contents SYS 0: No hang-up 1: 0.5 minutes (= 30 seconds) 2: 1 minute 3: 3 minutes 4: 5 minutes 5: 10 minutes 6: 15 minutes 7: 30 minutes 0: Local directory 1: REMOTE 1 2: REMOTE 2 Sets the notification method of scan job completion.
Code Classification 1784 Network 1785 Network 1786 Network 1800-0 Image processing 1800-1 Setting mode (08) Default Func- Single page data saving ALL 0 directory at "Save as file" <0-1> Page number display format of the file of "Save as file" and Email transmission Extension (suffix) format of the file of "Save as file" 1802-0 1802-1 1802-2 1911 Finisher 1912 Finisher 1913 General 1914 General 1915 Network 1916 General SYS Sets the directory where t
Code Classification 1920 Network 1921 Network 1922 Network 1923 Network 1924 Network 1925 Network 1926 FAX 1928 Setting mode (08) Default Func- Device domain name of ALL device authentication Windows domain No. 2 of ALL user authentication Windows domain No.
Setting mode (08) Default Func- AppleTalk device name ALL MFPserial Code Classification 1936 Network 1937 Network User name and password at user authentication or "Save as file" ALL 0 <0-2> SYS 1938 General Reformatting process due to a version change of SYS ROM ALL <0-2> - 1941 Bluetooth Bluetooth BIP Paper size ALL EUR: 6 UC: 2 JPN: 6 <0-13> SYS 1950 Network SMB signature for SMB server ALL 1 <0-3> UTY 1951 Network SMB signature for SMB client
Setting mode (08) Default Func- Device name for device ALL authentication Password for the device ALL name used for device authentication PDC2 of user authenticaALL tion BDC2 of user authenticaALL tion PDC3 of user authenticaALL tion BDC3 of user authenticaALL tion PDC of device authenticaALL tion BDC of device authenticaALL tion KS Filter operation mode ALL 0 <0-1> KS/KSSM setting all clearALL ing Code Classification 1952 Network 1953 Network 1954 Network 1955 Networ
Setting mode (08) Default Func- ALL 0 <0-5> Code Classification 1972 General KS Type Face 1973 General KS Font Size ALL 96 <96-160> SYS 1974 General KS Zoom ALL SYS 1975 General KS CR/LF Mode ALL 100 <20-400> 2 <0-3> 1976 General KS Top Margin ALL 0 <0-50> SYS 1977 General KS Left Margin ALL 0 <0-50> SYS 1978 General KS Auto Wrap ALL SYS 1979 General KS Han Mode ALL 1980 General KS Han Code ALL 1984 General KSSM CPI (English CPI/ Hangl
Code Classification 1986 General Items KSSM Type Face Setting mode (08) Default Func- ALL 0 <0-5> Procedur e RAM Contents SYS 0: MYUNGJO 1: GOTHIC 2: GUNGSEO 3: GULLIM 4: GRAPH 5: SAMMUL Key in the value 10 times as the desired font size. (e.g.: Key in "100" for a font size 10.0.) 1 0: CR->CR, LF->LF 1: CR->CR+LF, LF->LF 2: CR->CR, LF->CR+LF 3: CR->CR+LF, LF->CR+LF Key in the value 10 times as the desired font size. (e.g.: Key in "40" for a font size 4.0.
Setting mode (08) Default Func- ATalk PS active ConnecALL 10 tion <1-16> Raw TCP max connection ALL 10 <1-16> Raw TCP active connecALL 10 tion <1-16> DNS Client Time Out ALL 60 <1-180> Code Classification 3730 Network 3731 Network 3732 Network 3736 Network 3737 Network DDNS Client Time Out ALL 60 <1-180> NIC 3738 Network HTTP Client Time Out ALL 60 <1-180> NIC 3739 Network FTP Client Time Out (SCAN) ALL 30 <1-180> NIC 3740 Network SNTP Client Time
Code Classification 6810-0 Counter 6810-1 Setting mode (08) Default Func- Number of 1-UP / PPC 0 output pages Duplex (black) <8 digits> in black mode printing / Large size 2-UP / PPC 0 Duplex (black) <8 digits> printing RAM Contents SYS Counts the number of output pages printed only in the black mode. Counts the number of output pages printed in the black mode using [2IN1] or [MAGAZINE SORT].
Code Classification 6812-0 Counter 6812-1 Setting mode (08) Default Func- Number of 1-UP / PPC 0 output pages Duplex (color) <8 digits> in twin color printing mode / Large 2-UP / PPC 0 Duplex (color) <8 digits> printing RAM Contents SYS Counts the number of output pages printed only in the twin color mode. Counts the number of output pages printed in the twin color mode using [2IN1] or [MAGAZINE SORT].
Code Classification 6814-0 Counter 6814-1 Setting mode (08) Default Func- Number of 1-UP / PRT 0 output pages Duplex (color) <8 digits> of the printer printing or BOX / Large 2-UP / PRT 0 (Full color) Duplex (color) <8 digits> printing Contents SYS Counts the number of output pages printed only in the full color mode. Counts the number of output pages printed in the full color mode using [2IN1] or [MAGAZINE SORT].
Code Classification Items Setting mode (08) Default Func- ALL 0 <0-2> 9739 Maintenance Remote service Toner-end notification 9828 General Remote scanning mode ALL 9829 General Department management limitation setting ALL 9847 Finisher Hole punching setting ALL 9880 General ALL 9881 General Total counter transmission date setting (2) Day of total counter data transmission 9882 General Display mode of the used capacity on the e-Filing administrator page 9885
Note: In this equipment, a toner image is formed on the transfer belt prior to a paper feeding. When the feeding retry occurs and the transport timing is delayed, the toner image on the transfer belt is cleaned off without the 2nd transfer since the paper cannnot be reached for the 2nd transfer proccess. After that, the toner image fomation is retried while the paper is waited.
<>(Chap. 2.2.6) Note: In the pixel counter function, the twin color copy mode is regarded as the full color mode. Code Classification Setting mode (08) Default Func- Standard paper size setting ALL EUR: 0 UC: 1 JPN: 0 <0-1> Contents SYS Selects the standard paper size to convert it into the pixel count (%). 0: A4 1: LT Clears all information related to the pixel counter.
1512 Pixel counter Setting mode (08) Default Func- Toner cartridge reference ALL cleared date (M) (color) 1513 Pixel counter Toner cartridge reference cleared date (C) ALL (color) - SYS 1514 Pixel counter Toner cartridge reference cleared date (K) ALL - SYS 1515 Pixel counter Toner cartridge reference count started date (Y) ALL (color) - SYS 1516 Pixel counter Toner cartridge reference count started date (M) ALL (color) - SYS 1517 Pixel counter Tone
Code Classification Setting mode (08) Default Func- Number of output pages/ FAX <8 digits> black (Service technician (black) reference) RAM Contents SYS Counts the number of output pages converted to the standard paper size in the FAX function, black mode and service technician reference. [Unit. page] Counts the number of output pages converted to the standard paper size in the copy function, full color mode, toner K and toner cartridge reference. [Unit.
Code 1558 Classification Pixel counter Setting mode (08) Default Func- Number of output pages/ PRT <8 digits> full color (Y) (Toner car(color) tridge reference) RAM Contents SYS Counts the number of output pages converted to the standard paper size in the printer function, full color mode, toner Y and toner cartridge reference. [Unit.
Code Classification Setting mode (08) Default Func- Average pixel count/full PPC 0 color (Y+M+C+K) (Service (color) <0technician reference) 10000> RAM Contents SYS Displays the average pixel count in the copy function, full color mode, all toner and service technician reference. [Unit: 0.01%] Displays the average pixel count in the copy function, full color mode, toner Y and service technician reference. [Unit: 0.
Code 1585 Classification Pixel counter Setting mode (08) Default Func- Average pixel count/full PRT 0 color (C) (Service techni(color) <0cian reference) 10000> RAM Contents SYS Displays the average pixel count in the printer function, full color mode, toner C and service technician reference. [Unit: 0.01%] Displays the average pixel count in the printer function, full color mode, toner K and service technician reference. [Unit: 0.
Code Classification Setting mode (08) Default Func- Average pixel count/black PRT 0 (Service technician refer(black) <0ence) 10000> RAM Contents SYS Displays the average pixel count in the printer function, black mode and service technician reference. [Unit: 0.01%] Displays the average pixel count in the FAX function, black mode and service technician reference. [Unit: 0.
Code 1602 Classification Pixel counter Setting mode (08) Default Func- Latest pixel count/full color PRT 0 (Y) (Service technician ref- (color) <0erence) 10000> RAM Contents SYS Displays the latest pixel count in the printer function, full color mode, toner Y and service technician reference. [Unit: 0.01%] Displays the latest pixel count in the printer function, full color mode, toner M and service technician reference. [Unit: 0.
Code Classification Setting mode (08) Default Func- Average pixel count/full PPC 0 color (M) (Toner cartridge (color) <0reference) 10000> RAM Contents SYS Displays the average pixel count in the copy function, full color mode, toner M and toner cartridge reference. [Unit: 0.01%] Displays the average pixel count in the copy function, full color mode, toner C and toner cartridge reference. [Unit: 0.
Code 1618 Classification Pixel counter Setting mode (08) Default Func- Average pixel count/full PRT 0 color (K) (Toner cartridge (color) <0reference) 10000> RAM Contents SYS Displays the average pixel count in the printer function, full color mode, toner K and toner cartridge reference. [Unit: 0.01%] Displays the average pixel count in the printer function, black mode and toner cartridge reference. [Unit: 0.
Code Classification Setting mode (08) Default Func- Latest pixel count/full color PPC 0 (Y) (Toner cartridge refer(color) <0ence) 10000> RAM Contents SYS Displays the latest pixel count in the copy function, full color mode, toner Y and toner cartridge reference. [Unit:0.01%] Displays the latest pixel count in the copy function, full color mode, toner M and toner cartridge reference. [Unit: 0.
Code 1639 Classification Pixel counter Setting mode (08) Default Func- Latest pixel count/black PPC 0 (Toner cartridge reference) (black) <010000> RAM Contents SYS Displays the latest pixel count in the copy function, black mode and toner cartridge reference. [Unit: 0.01%] Displays the latest pixel count in the printer function, black mode and toner cartridge reference. [Unit: 0.01%] The pixel count data are divided into 10 ranges.
Code 1643-0 1643-1 Classification Pixel counter 1643-2 1643-3 1643-4 1643-5 1643-6 1643-7 1643-8 1643-9 1644-0 1644-1 1644-2 1644-3 1644-4 1644-5 1644-6 1644-7 1644-8 1644-9 Pixel counter Setting mode (08) Default Func- Pixel count 0-5% PPC <8 digits> distribution/ (color) full color (C) 5.1-10% PPC <8 digits> (color) 10.1-15% PPC <8 digits> (color) 15.1-20% PPC <8 digits> (color) 20.1-25% PPC <8 digits> (color) 25.1-30% PPC <8 digits> (color) 30.
Code 1645-0 1645-1 Classification Pixel counter 1645-2 1645-3 1645-4 1645-5 1645-6 1645-7 1645-8 1645-9 1646-0 1646-1 Pixel counter 1646-2 1646-3 1646-4 1646-5 1646-6 1646-7 1646-8 1646-9 © June 2005 TOSHIBA TEC Setting mode (08) Default Func- Pixel count 0-5% PRT <8 digits> distribution/ (color) full color (Y) 5.1-10% PRT <8 digits> (color) 10.1-15% PRT <8 digits> (color) 15.1-20% PRT <8 digits> (color) 20.1-25% PRT <8 digits> (color) 25.1-30% PRT <8 digits> (color) 30.
Code 1647-0 1647-1 Classification Pixel counter 1647-2 1647-3 1647-4 1647-5 1647-6 1647-7 1647-8 1647-9 1648-0 1648-1 1648-2 1648-3 1648-4 1648-5 1648-6 1648-7 1648-8 1648-9 Pixel counter Setting mode (08) Default Func- Pixel count 0-5% PRT <8 digits> distribution/ (color) full color (C) 5.1-10% PRT <8 digits> (color) 10.1-15% PRT <8 digits> (color) 15.1-20% PRT <8 digits> (color) 20.1-25% PRT <8 digits> (color) 25.1-30% PRT <8 digits> (color) 30.
Code 1649-0 1649-1 Classification Pixel counter 1649-2 1649-3 1649-4 1649-5 1649-6 1649-7 1649-8 1649-9 1650-0 1650-1 Pixel counter 1650-2 1650-3 1650-4 1650-5 1650-6 1650-7 1650-8 1650-9 © June 2005 TOSHIBA TEC Setting mode (08) Default Func- Pixel count 0-5% PPC <8 digits> distribution/ (black) black 5.1-10% PPC <8 digits> (black) 10.1-15% PPC <8 digits> (black) 15.1-20% PPC <8 digits> (black) 20.1-25% PPC <8 digits> (black) 25.1-30% PPC <8 digits> (black) 30.
Code 1651-0 1651-1 1651-2 1651-3 1651-4 1651-5 1651-6 1651-7 1651-8 1651-9 Classification Pixel counter Setting mode (08) Default Func- Pixel count 0-5% FAX <8 digits> distribution/ (black) black 5.1-10% FAX <8 digits> (black) 10.1-15% FAX <8 digits> (black) 15.1-20% FAX <8 digits> (black) 20.1-25% FAX <8 digits> (black) 25.1-30% FAX <8 digits> (black) 30.1-40% FAX <8 digits> (black) 40.1-60% FAX <8 digits> (black) 60.1-80% FAX <8 digits> (black) 80.