TOSHIBA Thermal Printer B-SA4T SERIES Option Installation Manual Document No. EO15-33001A Original Jul., 2005 (Revised Sep.
EO15-33001A (Revision Date: Feb. 14, 2008) TABLE OF CONTENTS Page 1. Cutter Module------------------------------------------------------------------------------------------------------ 1- 1 1.1 B-SA204-QM/ B-SA204-QM-R ---------------------------------------------------------------------------- 1- 1 1.2 B-SA204P-QM-R---------------------------------------------------------------------------------------------- 1- 4 2.
INSTALLATION PROCEDURE FOR OPTIONAL EQUIPMENT EO15-33001A 1. Cutter Module INSTALLATION PROCEDURE FOR OPTIONAL EQUIPMENT WARNING! 1. Turn the printer power off and disconnect the power cord before installing an optional equipment. 2. Be careful not to pinch your fingers or hands with the covers. 3. Be careful not to injure your fingers when installing the cutter module. 1. Cutter Module 1.
INSTALLATION PROCEDURE FOR OPTIONAL EQUIPMENT EO15-33001A 1. Cutter Module 2. Open the Front Cover wider. Remove the Front Cover by lifting it to disengage the hinge pins from the hinge. The Front Cover cannot be removed unless it is opened at an angle of over 100 degrees as the stoppers of the hinge prevent disengagement. 100° Front Cover Hinge Screw 3. Mount the Cutter Module Cover by inserting the hinge pins into the hinges. Cutter Module Cover Hinge 4.
INSTALLATION PROCEDURE FOR OPTIONAL EQUIPMENT EO15-33001A 1. Cutter Module 5. Connect the Cutter Harness to the connector at the front of the printer. Connector Cutter Harness 6. Close the Cutter Unit and secure it to the printer with the Set Screw. Set Screw Cutter Unit 7. Close the Cutter Module Cover. • Media loading procedure------------- Owner’s Manual, Section 2.3 • Operation check------------------------ Owner’s Manual, Section 2.
INSTALLATION PROCEDURE FOR OPTIONAL EQUIPMENT EO15-33001A 1. Cutter Module 1.2 B-SA204P-QM-R B-SA204P-QM-R is an optional cutter module for the B-SA4TP Series (Plastic cover). CAUTION! Do not connect/disconnect the cutter harness to/from the printer within one minute from a power off to protect the internal electrical circuit of the printer. • Packing List The following parts are supplied with the kit. Make sure you have all items shown below. Cutter Unit (1 pc.) Cutter Module Cover (1 pc.
INSTALLATION PROCEDURE FOR OPTIONAL EQUIPMENT EO15-33001A 1. Cutter Module 3. Mount the Cutter Module Cover by inserting the hinge pins into the hinges. Hinge Cutter Module Cover 4. Fit the Cutter Unit to the front of the printer by inserting the Hinge Pins into the Hinge Pin Holes. Hinge Pin Hinge Pin Hole Hinge Pin Hinge Pin Hole Cutter Unit 5. Close the Cutter Unit and secure it to the printer with the Set Screw.
INSTALLATION PROCEDURE FOR OPTIONAL EQUIPMENT EO15-33001A 1. Cutter Module 6. Secure the ground wire of the cutter unit to the printer with the B-3x6 screw removed in Step 1, as shown in the picture. 7. Connect the cutter harness to the connector at the front of the printer. Connector B-3x6 Screw Ground Wire Cutter Harness Ground Wire Cutter Harness 8. Close the Cutter Module Cover. After that, perform an operation check for a proper cut issue.
INSTALLATION PROCEDURE FOR OPTIONAL EQUIPMENT EO15-33001A (Revision Date: Jan. 19, 2006) 2. Strip Module 2. Strip Module NOTE: Make sure that the firmware version is V1.1 or greater. Firmware V1.0 does not support the strip module. 2.1 B-SA904-H-QM-R B-SA904-H-QM-R is an optional strip module for the B-SA4TM Series (Metal cover). • Packing List The following parts are supplied with the kit. Make sure you have all items shown below. Strip Unit (1 pc.) Strip Module Cover (1 pc.) SMW-3x6 Screw (4 pc.
INSTALLATION PROCEDURE FOR OPTIONAL EQUIPMENT EO15-33001A 2. Strip Module 2. Open the Front Cover wider. Remove the Front Cover by lifting it to disengage the hinge pins from the hinge. The Front Cover cannot be removed unless it is opened at an angle of over 100 degrees as the stoppers of the hinge prevent disengagement. 100° Front Cover Hinge Screw 3. Mount the Strip Module Cover by inserting the hinge pins into the hinges. Hinge Strip Module Cover 4.
INSTALLATION PROCEDURE FOR OPTIONAL EQUIPMENT EO15-33001A 2. Strip Module 5. Secure the Strip Unit to the printer with the two screws. Make sure that the Feed Roller Gear rotates smoothly. Strip Unit Feed Roller Gear SMW-3x6 Screw 6. Close the Strip Unit. Strip Unit 7. Connect the Strip Harness to the connector at the front of the printer. At this time, carefully avoid contact of the strip harness with the gears. Connector Gear Strip Harness Strip Harness 8. Close the Strip Module Cover.
INSTALLATION PROCEDURE FOR OPTIONAL EQUIPMENT EO15-33001A (Revision Date: Jan. 19, 2006) 2. Strip Module • Attaching the Cutter The enclosed cutter is used to tear off the batch-issued labels. Attach the cutter with the two SMW-3x6 screws as shown in the picture below. Insert the leading edge of the labels into the opening under the cutter.
INSTALLATION PROCEDURE FOR OPTIONAL EQUIPMENT EO15-33001A (Revision Date: Jan. 19, 2006) 2. Strip Module • System Mode Settings for Stripping PET Labels When using PET labels on the strip module, please set the following system mode parameters in advance. 1. Connect the printer to a PC. Turn the power ON. 2. Load a PET label stock on the printer. 3. Turn ON the printer while holding down the [FEED] key and [PAUSE] key. FEED PAUSE <1>DIAG. V1.1 4. When “<1>DIAG.
INSTALLATION PROCEDURE FOR OPTIONAL EQUIPMENT EO15-33001A (Revision Date: Jan. 19, 2006) 2. Strip Module 9. Turn off the printer, and then back to on. Send an issue command to the printer for strip issue. (Continued.) Turn the power OFF. Turn the power ON. Issue labels. 10. If necessary, fine adjust the print start position and strip position in the system mode. NOTES: 1. It is recommended that the print start position and strip position are adjusted on the actual print condition.
INSTALLATION PROCEDURE FOR OPTIONAL EQUIPMENT EO15-33001A (Revision Date: Jan. 19, 2006) 2. Strip Module 13. Press the [PAUSE] key repeatedly until “P.P.FEED” appears on the LCD. Continued. PAUSE 14. Press the [FEED] key to feed a label for checking the next label’s stop position. If the next label stops with its top edge aligning with the strip shaft edge, an adjustment is not required. Go to Step 15. <2>PARAMETER SET P.P.FEED +0.0mm PAUSE A label is fed.
INSTALLATION PROCEDURE FOR OPTIONAL EQUIPMENT EO15-33001A (Revision Date: Jan: 19, 2006) 2. Strip Module 2.2 B-SA904P-H-QM-R B-SA904P-H-QM-R is an optional strip module for the B-SA4TP Series (Plastic cover). • Packing List Strip Unit (1 pc.) Strip Module Cover (1 pc.) SMW-3x6 Screw (4 pcs.) Cutter (1 pc.) Guide Roller (1 pc.) Installation Manual (1 copy) NOTE: When issuing labels in batch mode even though the strip module is fitted, please use the provided cutter to tear off the issued labels.
INSTALLATION PROCEDURE FOR OPTIONAL EQUIPMENT EO15-33001A 2. Strip Module 2. Open the Front Cover wider. Remove the Front Cover by lifting it to disengage the hinge pins from the hinge. The Front Cover cannot be removed unless it is opened at an angle of over 100 degrees as the stoppers of the hinge prevent disengagement. 100° Front Cover Hinge Stopper 3. Mount the strip Module Cover by inserting the hinge pins into the hinges. Hinge Strip Module Cover Hinge 4.
INSTALLATION PROCEDURE FOR OPTIONAL EQUIPMENT EO15-33001A 2. Strip Module 5. Secure the Strip Unit to the printer with the two screws. Make sure that the Feed Roller Gear rotates smoothly. Strip Unit Feed Roller Gear SMW-3x6 Screw 6. Close the Strip Unit. Strip Unit 7. Close the Strip Module Cover. Perform an operation check for a proper strip issue. • Media loading procedure------------- Owner’s Manual, Section 2.3 • Operation check------------------------ Owner’s Manual, Section 2.
INSTALLATION PROCEDURE FOR OPTIONAL EQUIPMENT EO15-33001A (Revision Date: Jan. 19, 2006) 2. Strip Module • Attaching the Cutter The enclosed cutter is used to tear off the batch-issued labels. Attach the cutter with the two SMW-3x6 screws as shown in the picture below. Insert the leading edge of the labels into the opening under the cutter.
INSTALLATION PROCEDURE FOR OPTIONAL EQUIPMENT EO15-33001A (Revision Date: Jan. 19, 2006) 3. Wireless LAN Module: B-SA704-WLAN-QM 3. Wireless LAN Module: B-SA704-WLAN-QM The pictures used in this section are those of the B-SA4TM, and the installation procedures are common with the B-SA4TP unless otherwise noted. • Packing List The following parts are supplied with the kit. Make sure you have all items shown below. Wireless LAN Board (1 pc.) Antenna Cover (1 pc.) SMW-3x6 Screw (4 pcs.
INSTALLATION PROCEDURE FOR OPTIONAL EQUIPMENT EO15-33001A 3. Wireless LAN Module: B-SA704-WLAN-QM • Installation Procedure 1. Remove the two SMW-3x6 screws from the back of the printer. Side Panel SMW-3x6 2. Remove the Side Panel in the following order. Please note the procedure is different between the BSA4TM series and the B-SA4TP series. B-SA4TM (1).Open the Top Cover and Front Cover. B-SA4TP Open the Top Cover. Slide the Side Panel backward, and then remove it in the direction of arrow A.
INSTALLATION PROCEDURE FOR OPTIONAL EQUIPMENT EO15-33001A (Revision Date: Jan. 19, 2006) 3. Wireless LAN Module: B-SA704-WLAN-QM 3. Remove the two SMW-3x6 screws to detach the Blind Plate. Blind Plate SMW-3x6 4. Remove the SMW-3x8 screw to detach the Cable Clamp. Cable Clamp SMW-3x8 Screw 5. Put the Antenna of the Wireless LAN Board out of the opening in the printer back. Care must be taken not to hit the Antenna against the printer frame, as damaged antenna may affect the performance.
INSTALLATION PROCEDURE FOR OPTIONAL EQUIPMENT EO15-33001A (Revision Date: Jan. 19, 2006) 3. Wireless LAN Module: B-SA704-WLAN-QM 6. As the following picture shows, secure the Wireless LAN Board to the printer back with two of the enclosed SMW-3x6 screws. Also, secure the Wireless LAN Board to the PCB Support Plate with the SMW-3x8 screw together with the Cable Clamp removed in Step 4. Copper foil PCB Support Plate Print Head Cable Cable Clamp SMW-3x8 Screw Wireless LAN Board SMW-3x6 Screw 7.
INSTALLATION PROCEDURE FOR OPTIONAL EQUIPMENT EO15-33001A 3. Wireless LAN Module: B-SA704-WLAN-QM 8. Connect the Wireless LAN Power Cable and the LAN Cable as shown below. CN12 CN17 LAN Cable 9. Wireless LAN Power Cable Fit the Antenna Cover to the back of the printer. Secure it with the SMW-3x6 screw. SMW-3x6 Screw Antenna Cover Pass the LAN Cable through the cut of the Antenna Cover. LAN Cable 10. Re-attach the Side Panel to the printer.
INSTALLATION PROCEDURE FOR OPTIONAL EQUIPMENT EO15-33001A 3. Wireless LAN Module: B-SA704-WLAN-QM • Country Code As available frequency bands are different from country to country, be sure to set a country code before installing a wireless LAN module in a user’s printer. Also, ask an end user to confirm a country code. Use of a wireless LAN module with a wrong country code could violate each country’s Laws and Regulations for Radio Equipment, and violators could be subject to penalties.
INSTALLATION PROCEDURE FOR OPTIONAL EQUIPMENT EO15-33001A 4. Serial Interface Board: B-SA704-RS-QM-R 4. Serial Interface Board: B-SA704-RS-QM-R The pictures used in this section are those of the B-SA4TM, and the installation procedures are common with the B-SA4TP unless otherwise noted. • Packing List The following parts are supplied with the kit. Make sure you have all items shown below. SIO PC Board (1 pc.) Locking Support (1 pc.) PCB Support Plate (1 pc.
INSTALLATION PROCEDURE FOR OPTIONAL EQUIPMENT EO15-33001A 4. Serial Interface Board: B-SA704-RS-QM-R 2. Remove the Side Panel in the following order. Please note the procedure is different between the BSA4TM series and the B-SA4TP series. B-SA4TM (1).Open the Top Cover and Front Cover. B-SA4TP Open the Top Cover. Slide the Side Panel backward, and then remove it in the direction of arrow A. Top Cover Top Cover Front Cover Side Panel A (2).Remove the two SMW-3x6 screws which secure the Side Panel.
INSTALLATION PROCEDURE FOR OPTIONAL EQUIPMENT EO15-33001A 4. Serial Interface Board: B-SA704-RS-QM-R 4. Attach the enclosed PCB Support Plate to the printer back with one of the enclosed SMW-3x6 screws. SMW-3x6 PCB Support Plate 5. Fit the Locking Support into the MAIN PC Board. Locking Support MAIN PC Board 6. Connect the Serial Interface Cable of the SIO PC Board to CN12 on the MAIN PC Board.
INSTALLATION PROCEDURE FOR OPTIONAL EQUIPMENT EO15-33001A 4. Serial Interface Board: B-SA704-RS-QM-R 7. Secure the SIO PC Board to the printer back with the two SMW-3x6 screws. Fit the Locking Support into the SIO PC Board. SIO PC Board SMW-3x6 Locking Support 8. 9. Re-attach the Side Panel. For an operation check, settings, etc., refer to the.
INSTALLATION PROCEDURE FOR OPTIONAL EQUIPMENT EO15-33001A 5. 300 dpi Print Head Kit: B-SA704-TPH3-QM-R 5. 300 dpi Print Head Kit: B-SA704-TPH3-QM-R B-SA704-TPH3-QM-R is an optional 300 dpi print head kit for the B-SA4TM/SA4TP-GS12 Series (203dpi printer). You will obtain the same print quality as the TS12 model (300 dpi) only by replacing the current print head with this optional kit.
INSTALLATION PROCEDURE FOR OPTIONAL EQUIPMENT EO15-33001A 7. Expansion IO Board: B-SA704-IO-QM-R • Installation Procedure 1. Fully open the Ribbon Cover. 2. Slightly open the Top Cover (10 mm). Ribbon Cover Top Cover 3. Unlock the Print Head by pressing the hooks toward the center. Then pull the Print Head downward. NOTE: Care must be taken not to damage the Print Head Element by hitting it against any metal parts. Hook Print Head 4. Disconnect the Print Head Cable from the Print Head.
INSTALLATION PROCEDURE FOR OPTIONAL EQUIPMENT EO15-33001A (Revision Date: Jan. 19, 2006) 6. Real Time Clock: B-SA704-RTC-QM-R 6. Real Time Clock: B-SA704-RTC-QM-R B-SA704-RTC-QM-R is an optional Real Time Clock for the B-SA4TM/SA4TP Series. The pictures used in this section are those of the B-SA4TP, and the installation procedures are common with the B-SA4TM unless otherwise noted.
INSTALLATION PROCEDURE FOR OPTIONAL EQUIPMENT EO15-33001A (Revision Date: Jan. 19, 2006) 6. Real Time Clock: B-SA704-RTC-QM-R 2. Remove the Side Panel in the following order. Please note the procedure is different between the BSA4TM series and the B-SA4TP series. B-SA4TM (1).Open the Top Cover and Front Cover. B-SA4TP Open the Top Cover. Slide the Side Panel backward, and then remove it in the direction of arrow A. Top Cover Top Cover Front Cover Side Panel A (2).
INSTALLATION PROCEDURE FOR OPTIONAL EQUIPMENT EO15-33001A (Revision Date: Jan. 19, 2006) 6. Real Time Clock: B-SA704-RTC-QM-R NOTES: 1. Place the battery with the “+” mark facing up. 2. A new battery is supposed to last about 2 years or more, but it varies depending on the operating conditions. When a new battery is loaded, write down the battery replacement date on a supplied battery sticker, and attach it to the reverse side of the Side Panel as a reminder.
INSTALLATION PROCEDURE FOR OPTIONAL EQUIPMENT EO15-33001A (Revision Date: Jan. 19, 2006) 6. Real Time Clock: B-SA704-RTC-QM-R 5. Pass the Interface Cable through the Cable Clamp, and between CN1 and CN2 on the MAIN PC Board, as shown in the pictures below. For the B-SA4TP model, wind the cable on the two Cable Clamps. B-SA4TP Model Connector CN2 MAIN PC Board Interface Cable Connector CN1 B-SA4TM Model Cable Clamp Interface Cable Connector CN2 MAIN PC Board Interface Cable Connector CN1 6.
INSTALLATION PROCEDURE FOR OPTIONAL EQUIPMENT EO15-33001A (Revision Date: Jan. 19, 2006) 6. Real Time Clock: B-SA704-RTC-QM-R • System Setting (Date and Time Setting) Set the date and time using the following procedure. NOTE: Make sure that the printer version is V1.2 or greater. The real time clock is not supported by V1.1 or older. 1. Turn on the printer. displayed on the LCD. Power ON “ONLINE” will be ONLINE B-SA4T 2. 3. Press the [PAUSE] key to turn the printer to pause state.
INSTALLATION PROCEDURE FOR OPTIONAL EQUIPMENT EO15-33001A (Revision Date: Jan. 19, 2006) 6. Real Time Clock: B-SA704-RTC-QM-R 10. Pressing the [PAUSE] key enables setting the Hour. 11. Set the Hour with the [FEED] or [RESTART] key. Pressing the [PAUSE] key fixes the Hour and cause the cursor to move to the Minute. 12. Set the Minute with the [FEED] or [RESTART] key. Pressing the [PAUSE] key fixes the Minute and cause the cursor to move to the Second. 13. Set the second with the [FEED] or [RESTART] key.
INSTALLATION PROCEDURE FOR OPTIONAL EQUIPMENT EO15-33001A (Revision Date: Jan. 19, 2006) 7. Expansion I/O Board: B-SA704-IO-QM-R 7. Expansion I/O Board: B-SA704-IO-QM-R B-SA704-IO-QM-R is an optional expansion I/O board for the B-SA4TM/SA4TP Series. The pictures used in this section are those of the B-SA4TP, and the installation procedures are common with the B-SA4TM unless otherwise noted. • Packing List The following parts are supplied with the kit. Make sure you have all items shown below.
INSTALLATION PROCEDURE FOR OPTIONAL EQUIPMENT EO15-33001A (Revision Date: Jan. 19, 2006) 7. Expansion I/O Board: B-SA704-IO-QM-R 2. Remove the Side Panel in the following order. Please note the procedure is different between the BSA4TM series and the B-SA4TP series. B-SA4TM (1).Open the Top Cover and Front Cover. B-SA4TP Open the Top Cover. Slide the Side Panel backward, and then remove it in the direction of arrow A. Top Cover Top Cover Front Cover Side Panel A (2).
INSTALLATION PROCEDURE FOR OPTIONAL EQUIPMENT EO15-33001A (Revision Date: Jan. 19, 2006) 7. Expansion I/O Board: B-SA704-IO-QM-R 4. Attach the Expansion I/O Board to the printer back with one of the supplied SMW-3x6 screws. SMW-3ｘ6 Screw Expansion I/O Board 5. Connect the Interface Cable to CN4 on the MAIN PC Board. CN4 Connector Expansion I/O Board MAIN PC Board Interface Cable 6. Attach the supplied Blind Plate to the printer back with the supplied two SMW-3x6 screws.
INSTALLATION PROCEDURE FOR OPTIONAL EQUIPMENT EO15-33001A (Revision Date: Feb. 14, 2008) 8. RFID Module: B-SA704-RFID-U2-EU-R 8. RFID Module: B-SA704-RFID-U2-EU-R This optional device is intended for adding the RFID tag read/write function to the B-SA4TM and B-SA4TP series. WARNING! 1. Follow all manual instructions. Failure to do so could create safety hazards such as fire or electrocution.
INSTALLATION PROCEDURE FOR OPTIONAL EQUIPMENT EO15-33001A (Revision Date: Feb. 25, 2008) 8. RFID Module: B-SA704-RFID-U2-EU-R • Packing List All the following parts are supplied with the kit. Make sure you have all items shown below. Parts (Quantity) Parts (Quantity) Parts (Quantity) Antenna Ass’y (1 pc.) RFID Module (1 pc.) Antenna Cable (1 pc.) Interface Cable (1 pc.) Shield Sheet (for the use of short-pitch tags) (1 pc.) RFID Module Attaching Plate (1 pc.) Cable Clamp (1 pc.
INSTALLATION PROCEDURE FOR OPTIONAL EQUIPMENT EO15-33001A (Revision Date: Feb. 25, 2008) 8. RFID Module: B-SA704-RFID-U2-EU-R • Outline of the introduction of an RFID Kit Please follow the steps below to install the RFID kit, configure various settings, and try data write onto tags. (1) Install the RFID kit. (Refer to this section.) (2) Set an RFID module type, tag type, etc. in the printer system mode. (Refer to this section or section 2.9 of system mode manual.
INSTALLATION PROCEDURE FOR OPTIONAL EQUIPMENT EO15-33001A (Revision Date: Feb. 25, 2008) 8. RFID Module: B-SA704-RFID-U2-EU-R 2. Remove the Side Panel in the following order. Please note the procedure is different between the BSA4TM series and the B-SA4TP series. B-SA4TM 1. Open the Top Cover and Front Cover. Top Cover B-SA4TP Open the Top Cover. Slide the Side Panel backward, and then remove it in the direction of arrow A. Top Cover Side Panel Front Cover 2.
INSTALLATION PROCEDURE FOR OPTIONAL EQUIPMENT EO15-33001A (Revision Date: Feb. 25, 2008) 8. RFID Module: B-SA704-RFID-U2-EU-R 3. Slightly push the Upper Sensor Lever inside (1), and open the Upper Sensor Ass’y (2). Upper Sensor Ass’y (2) Upper Sensor Lever (1) 4. Pushing the tabs on the rear of the Media Sensor Block toward the front of the printer, slightly lift the back of the Media Sensor Block, and remove it toward the printer back. Tab Media Sensor Block Tab 5.
INSTALLATION PROCEDURE FOR OPTIONAL EQUIPMENT EO15-33001A (Revision Date: Feb. 25, 2008) 8. RFID Module: B-SA704-RFID-U2-EU-R 6. As the following picture shows, pass the Interface Cable through the opening behind the Stepping Motor so that the cable reaches the Main PC Board. Opening Interface Cable Stepping Motor 7. Connect the Interface Cable to CN6 on the Main PC Board. CN6 Main PC Board 8. Interface Cable Put the Interface Cable on the hooks provided on the Media Path Frame.
INSTALLATION PROCEDURE FOR OPTIONAL EQUIPMENT EO15-33001A (Revision Date: Feb. 25, 2008) 8. RFID Module: B-SA704-RFID-U2-EU-R 9. Fit the supplied Edge Guards on the metal plate all the way to their bottoms. • Please be careful not to injure your hands while fitting the Edge Guards. • Fit the long Edge Guards and short ones on the correct positions respectively, as indicated in the pictures below. • The Edge Guards should not protrude from the edge of the metal plate (portions enclosed with circles).
INSTALLATION PROCEDURE FOR OPTIONAL EQUIPMENT EO15-33001A (Revision Date: Feb. 25, 2008) 8. RFID Module: B-SA704-RFID-U2-EU-R 12. Connect the Interface Cable to the RFID Module. Interface Cable RFID Module 13. Secure the RFID Module to the printer with a supplied Double Sems Screw. Double Sems Screw M-3x6 RFID Module 14.
INSTALLATION PROCEDURE FOR OPTIONAL EQUIPMENT EO15-33001A (Revision Date: Feb. 25, 2008) 8. RFID Module: B-SA704-RFID-U2-EU-R 15. Re-place the Media Sensor Block. Media Sensor Block 16. Connect the Antenna Cable to the Antenna Ass’y until it clicks, and fasten the Antenna Cable with the Cable Clamp, as shown below. Antenna Cable Antenna Ass’y Cable Clamp 17. Reattach the Side Panel to the printer with reference to Step 2. 18. Close the Front Cover and the Top Cover.
INSTALLATION PROCEDURE FOR OPTIONAL EQUIPMENT EO15-33001A (Revision Date: Feb. 25, 2008) 8. RFID Module: B-SA704-RFID-U2-EU-R 2. Insert the Shield Sheet, without the backing paper removed, under the Media Guides from behind, and slightly slide it toward the Platen. Then, move the Media Guides to the width of the Shield Sheet (shorter width), as the pictures show. The purpose of this is to indicate the center of the attachment position. Platen Media Guide Shield Sheet Media Guide Media Guide 3.
INSTALLATION PROCEDURE FOR OPTIONAL EQUIPMENT EO15-33001A (Revision Date: Feb. 25, 2008) 8. RFID Module: B-SA704-RFID-U2-EU-R • RFID Module Settings After installing the RFID Module on the printer, configure the RFID module settings using the system mode on the printer. Turn on the printer while holding down the [FEED] and [PAUSE] keys at the same time. <1>DIAG. V1.6 When “<1>DIAG. V1.6“ appears on the LCD, press the [RESTART] key. [RESTART] RFID setting menu ”<10>RFID” is displayed.
INSTALLATION PROCEDURE FOR OPTIONAL EQUIPMENT EO15-33001A (Revision Date: Feb. 25, 2008) 8. RFID Module: B-SA704-RFID-U2-EU-R Continued from the previous page. <10>RFID TAG NONE RFID tag type setting menu is displayed. Choose “EPC C1 Gen2: 24” with the [FEED] or [RESTART] key. [RESTART] NONE: When a tag type is not selected. EPC C1 Gen2: 24 [FEED] [PAUSE] <10>RFID ERR CHK Press the [PAUSE] key. RFID error tag detection menu is displayed.
INSTALLATION PROCEDURE FOR OPTIONAL EQUIPMENT EO15-33001A (Revision Date: Feb. 25, 2008) 8. RFID Module: B-SA704-RFID-U2-EU-R Continued from the previous page. <10>RFID R CYCLE TIM 4.0 Read retry timeout setting menu is displayed. Set the timeout period during which RFID tag read retries are allowed, with the [FEED] or [RESTART] key. If the printer has retried for the max. number of times within the RFID read retry timeout, the printer stops the retries at the time.
INSTALLATION PROCEDURE FOR OPTIONAL EQUIPMENT EO15-33001A (Revision Date: Feb. 25, 2008) 8. RFID Module: B-SA704-RFID-U2-EU-R Continued from the previous page <10>RFID ADJ RETRY +00 RFID adjustment for retry menu is displayed. If writing data on a tag failed, the printer feeds the RFID tag forward or backward for specified length in order to retry writing data. When “0” is set for this parameter, this function and a retry are not performed.
INSTALLATION PROCEDURE FOR OPTIONAL EQUIPMENT EO15-33001A (Revision Date: Feb. 25, 2008) 8. RFID Module: B-SA704-RFID-U2-EU-R Continued from the previous page. <10>RFID Q VALUE 2 Q value setting menu is displayed. In the case multiple RFID tags are read at the same time, this menu is useful to pinpoint a target tag. Set the Q value to “1” or greater (2 is recommended.) with the [FEED] or [RESTART] key. Q value “0” causes the tags to interfere with each other and disables proper data write.
INSTALLATION PROCEDURE FOR OPTIONAL EQUIPMENT EO15-33001A (Revision Date: Feb. 25, 2008) 8. RFID Module: B-SA704-RFID-U2-EU-R • AGC Threshold Setting The B-SA704-RFID-U2-EU-R chooses a tag to write data on according to a radio intensity of RFID tags (AGC value). An AGC threshold value has been set to 11 (0Bh) as factory default, but it may be necessary to change this value according to the tag type to be used.
INSTALLATION PROCEDURE FOR OPTIONAL EQUIPMENT EO15-33001A (Revision Date: Feb. 25, 2008) 8. RFID Module: B-SA704-RFID-U2-EU-R Continued from the previous page 3132333435363738 39304142 (0A) [FEED], [RESTART] Data in parentheses ( ) is the AGC value expressed in hex. code. Write down this value. Press the [FEED] and [RESTART] keys to return to the RFID Setting Menu (”<10>RFID”). <10>RFID 3) Read data is displayed. Set an AGC threshold of data write.
INSTALLATION PROCEDURE FOR OPTIONAL EQUIPMENT EO15-33001A (Revision Date: Nov. 7, 2008) 8. RFID Module: B-SA704-RFID-U2-EU-R • Identification of The Rfid Module (B-SA704-RFID-U2-EU-R) As from the production manufactured in October 2008, the standard label has been added to the RFID module, which is used for the B-SA4T series, for improving the efficiency of assembly. RFID Module Service No. Label B-SA704-RFID-U2-EU-R Serial No.
