© 2009 by TOSHIBA Corporation. All rights reserved. Under the copyright laws, this manual cannot be reproduced in any form without the prior written permission of TOSHIBA. No patent liability is assumed, with respect to the use of the information contained herein.
Wi-Fi is a registered trademark of the Wi-Fi Alliance. Memory Stick and Memory Stick PRO are registered trademarks of SONY Corporation. Secure Digital and SD are trademarks of SD Card Association. MultiMediaCard and MMC are trademarks of MultiMediaCard Association. Other trademarks and registered trademarks not listed above may be used in this manual. This product incorporates copyright protection technology that is protected by U.S. patents and other intellectual property rights, including U.S.
Only peripherals complying with the FCC class B limits may be attached to this equipment. Operation with non-compliant peripherals or peripherals not recommended by TOSHIBA is likely to result in interference to radio and TV reception. Shielded cables must be used between the external devices and the computers external monitor port, Universal Serial Bus (USB 2.0) ports, HDMI out port and microphone jack.
The equipment has been approved to [Commission Decision CTR21] for pan-European single terminal connection to the Public Switched Telephone Network (PSTN). However, due to differences between the individual PSTNs provided in different countries/regions the approval does not, of itself, give an unconditional assurance of successful operation on every PSTN network termination point. In the event of problems, you should contact your equipment supplier in the first instance.
If you are using the computer in Japan, technical regulations described under Telecommunications Business Law require that you select the Japan region mode. It is illegal to use the modem in Japan with any other selection. Up to two redial attempts can be made. If more than two redial attempts are made, the modem will return Black Listed. If you are experiencing problems with the Black Listed code, set the interval between redials at one minute or longer.
The goal of the telephone company is to provide you with the best service it can. In order to do this, it may occasionally be necessary for them to make changes in their equipment, operations, or procedures. If these changes might affect your service or the operation of your equipment, the telephone company will give you notice in writing to allow you to make any changes necessary to maintain uninterrupted service.
1. The Industry Canada label identifies certified equipment. This certification means that the equipment meets certain telecommunications network protective, operational and safety requirements as prescribed in the appropriate Terminal Equipment Technical Requirements document(s). The Department does not guarantee the equipment will operate to the users satisfaction.
Modems connected to the Australian telecoms network must have a valid Austel permit. This modem has been designed to specifically configure to ensure compliance with Austel standards when the country/region selection is set to Australia. The use of other country/region settings while the modem is attached to the Australian PSTN would result in your modem being operated in a non-compliant manner.
Some parameters required for compliance with Telecoms PTC Specifications are dependent on the equipment (PC) associated with this modem.
The transmit level from this device is set at a fixed level and because of this there may be circumstances where the performance is less than optimal. Before reporting such occurrences as faults, please check the line with a standard Telepermitted telephone, and only report a fault if the phone performance is impaired. It is recommended that this equipment be disconnected from the Telecom line during electrical storms.
Disposal of products The crossed out wheeled dust bin symbol indicates that products must be collected and disposed of separately from household waste. Integrated batteries and accumulators can be disposed of with the product. They will be separated at the recycling centres. The black bar indicates that the product was placed on the market after August 13, 2005.
Your Computer model may be ENERGY STAR® compliant. If the model you purchased is compliant, it is labeled with the ENERGY STAR logo on the computer and the following information applies. TOSHIBA is a partner in the ENERGY STAR Program and has designed this computer to meet the latest ENERGY STAR guidelines for energy efficiency.
TOSHIBA Satellite L450/Pro L450/L450D/Pro L450D series computer is shipped with one of the following drives preinstalled: DVD Super Multi (+-R DL) drive or DVD Super Multi (+-R DL) /w Label Flash drive.
DVD Super Multi (+-R DL) drive Panasonic UJ890A/UJ890E HLDS GT20N/GT20F Users Manual xv
Toshiba Samsung TS-L633C/TS-L633Y Users Manual xvi
CAUTION: This appliance contains a laser system and is classified as a CLASS 1 LASER PRODUCT. To use this model properly, read the instruction manual carefully and keep this manual for your future reference. In case of any trouble with this model, please contact your nearest AUTHORIZED service station. To prevent direct exposure to the laser beam, do not try to open the enclosure. VORSICHT: Dieses Gerät enthält ein Laser-System und ist als LASERSCHUTZKLASSE 1 PRODUKT klassifiziert.
OBS! Apparaten innehåller laserkomponent som avger laserstråining överstigande gränsen för laserklass 1. VAROITUS. Suojakoteloa si saa avata. Laite sisältää laserdiodin, joka lähetää näkymätöntä silmilie vaarallista lasersäteilyä. CAUTION: USE OF CONTROLS OR ADJUSTMENTS OR PERFORMANCE OF PROCEDURES OTHER THAN THOSE SPECIFIED IN THE OWNERS MANUAL MAY RESULT IN HAZARDOUS RADIATION EXPOSURE.
Table of Contents Copyright. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ii Disclaimer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ii Trademarks . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ii Macrovision License of Notice . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . iii FCC information . . . . . . . . . . . . . . . . . . . . . . . .
Chapter 2 The Grand Tour Chapter 3 Getting Started Chapter 4 Operating Basics Chapter 5 The Keyboard Chapter 6 Power and Power-up Modes Users Manual Front with the display closed . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-1 Left side . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-2 Right side . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-4 Back side. . . . . . . . . . . . .
Power indicators. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-2 Battery types. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-3 Care and use of the battery pack . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-5 Replacing the battery pack . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-9 TOSHIBA Password Utility. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-12 Power-up modes.
V.90/V.92 mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . C-1 AT Command. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . C-3 Appendix D Wireless LAN 1 Appendix E AC Power Cord and Connectors 1 Card Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . D-1 Radio Characteristics. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Congratulations on your purchase of the TOSHIBA Satellite L450/Pro L450/L450D/Pro L450D series computer. This powerful notebook computer provides excellent expansion capability, includes multimedia functionality, and is designed to provide years of reliable, high-performance computing. This manual tells how to set up and begin using your TOSHIBA Satellite L450/Pro L450/L450D/Pro L450D series computer.
Preface Chapter 5, The Keyboard, describes special keyboard functions including the keypad overlay and hot keys. Chapter 6, Power and Power-up Modes, gives details on the computers power resources and battery save modes. Chapter 7, HW Setup and Passwords, explains how to configure the computer using the HW Setup program. It also tells how to set a password. Chapter 8, Optional Devices, describes the optional hardware available.
Preface ABC ABC When procedures require an action such as clicking an icon or entering text, the icon's name or the text you are to type in is represented in the typeface you see to the left. Names of windows or icons or text generated by the computer that appear on its display screen are presented in the type face you see to the left. Messages are used in this manual to bring important information to your attention. Each type of message is identified as shown below.
TOSHIBA computers are designed to optimize safety, minimize strain and withstand the rigors of portability. However, certain precautions should be observed to further reduce the risk of personal injury or damage to the computer. Be certain to read the general precautions below and to note the cautions included in the text of the manual. Place the computer on a flat surface that is large enough for the computer and any other items you are using, such as a printer.
General Precautions Avoid prolonged physical contact with the computer. If the computer is used for long periods, its surface can become very warm. While the temperature will not feel hot to the touch, if you maintain physical contact with the computer for a long time, for example if you rest the computer on your lap or if you keep your hands on the palm rest, your skin might suffer a low-heat injury.
This chapter provides an equipment checklist, and it identifies the computers features, options and accessories. Some of the features described in this manual may not function properly if you use an operating system that was not pre-installed by TOSHIBA. Carefully unpack your computer, taking care to save the box and packaging materials for future use.
Introduction The following Windows® operating system and utility software are pre-installed.
Introduction This computer incorporates the following features and benefits: Processor Built-in Your computer is equipped with one processor and processor type varies depending on model. To check which type of processor is included in your model, open the TOSHIBA PC Diagnostic Tool Utility by clicking Start All programs TOSHIBA Utilities PC Diagnostic Tool.
Introduction Video RAM Video RAM depends on the model you purchased. Mobile Intel® GM45 Express Chipset model/ Mobile Intel® GL40 Express Chipset model: Video RAM capacity shares with main memory, and the proportion depends on Dynamic Video Memory Technology. AMD M780G Chipset model/ AMD M780V Chipset model: Video RAM capacity shares with main memory, and the proportion depends on ATI HyperMemoryTM.
Introduction Pointing Device Built-in Touch Pad The integrated Touch Pad and control buttons in the palm rest allow control of the on-screen pointer and support functions such as the scrolling of windows. Power Battery pack The computer is powered by one rechargeable lithium-ion battery pack. RTC battery The internal RTC battery backs up the Real Time Clock (RTC) and calendar. AC adaptor The AC adaptor provides power to the system and recharges the batteries when they are low.
Introduction Multimedia Sound system The integrated sound system provides support for the computer's internal speakers and microphone, also allowing an external microphone and headphones to be connected via the appropriate jacks. Web Camera Web Camera is a device that allows you to record video or take photographs with your computer. You can use it for video chatting or video conferences using a communication tool such as Windows Live Messenger.
Introduction The transmission speed over the wireless LAN and the distance over which wireless LAN can reach may vary depending on surrounding electromagnetic environment, obstacles, access point design and configuration, and client design and software/hardware configurations. The Transmit Rate (at X Mbit/s) is the theoretical maximum speed under the IEEE802.11 (a/b/g/n) standards. The actual transmission speed will be lower than the theoretical maximum speed.
Introduction Optical disc drive Users Manual DVD Super Multi drive The drive reads DVD-ROM's at a maximum 8x speed and CD-ROM's at a maximum 24x speed, and writes CD-R's at up to 24x speed, CD-RW's at up to 24x speed, DVD-R's and DVD+R's at up to 8x speed, DVD-RW's at up to 6x speed, DVD+RW's at up to 8x speed, DVD-R (Dual layer) at up to 6x speed, DVD+R (Double Layer) at up to 6x speed and DVD-RAM at up to 5x speed, and supports the following formats: CD-R CD-RW DVD-ROM DVD-Video CD-DA CD-Text Photo C
Introduction Software The computer's internal display panel supports high-resolution video graphics and can be set to a wide range of viewing angles for maximum comfort and readability. Operating system Windows® 7 is available. Refer to the preinstalled Software section at the front of this chapter. TOSHIBA Utilities A number of utilities and drivers are preinstalled to make your computer more convenient to use. Refer to the Utilities and applications section in this chapter.
Introduction Keypad overlay A ten-key numeric keypad is integrated into the keyboard. Please refer to the Keypad overlay section in Chapter 5, The Keyboard, for information on using this feature. Power on password Two levels of password security, supervisor and user, are available to prevent unauthorized access to your computer. Instant security A specific hot key function automatically locks the system providing data security.
Introduction Sleep Mode If you have to interrupt your work, you can use this feature to allow you to turn off power to the computer without exiting from your software. Data is maintained in the computer's main memory so that when you next turn on the power, you can continue working right where you left off. This section describes the TOSHIBA Component features pre-installed on the computer.
Introduction This section describes the pre-installed utilities that come with the computer and details how to start them. For further information on their operation, please refer to each utility's online manual, help files or README.TXT file. TOSHIBA Face Recognition TOSHIBA Face Recognition uses a face verification library to verify the face data of users when they log in to Windows. If the verification is successful, the user will be logged into Windows automatically.
Introduction TOSHIBA DVD-RAM Utility This utility has the function of Physical Format and Write-Protect to DVD-RAM. This utility is contained the setup module of TOSHIBA Disc Creator. To start this utility, click Start All Programs TOSHIBA CD&DVD Applications DVD-RAM Utility. Corel DVD MovieFactory for TOSHIBA Corel DVD MovieFactory for TOSHIBA allows users to instantly create DVD video or slideshow discs via a user-friendly wizard interface with specific task oriented features.
Introduction Windows Mobility Center This section describes the Windows Mobility Center. Mobility Center is a utility for accessing several mobile PC settings quickly in one window. A default maximum of eight tiles are provided by the operating system, and the additional two tiles are added to your Mobility Center. Lock Computer: This can be used to lock your computer without turning it off. This has the same function as the Lock button at the bottom of the right pane of the start menu.
Introduction You can add a number of options to make your computer even more powerful and convenient to use. The following options are available: Users Manual Memory expansion 1GB or 2GB memory module (PC2-6400) can easily be installed in the computer. Battery Pack An additional battery pack can be purchased for use as either a spare or replacement. Please refer to Chapter 6, Power and Power-up Modes for futher information.
This chapter identifies the various components of your computer. Become familiar with each component before you operate the computer. The following figure shows the computers front with its display panel in the closed position. 1. Bridge media slot 2. Microphone jack 3. Headphone jack 4. Volume control Figure 2-1 Front of the computer with display closed Bridge media slot This slot lets you insert an SD/SDHC memory card, miniSD/microSD Card, Memory Stick® (PRO) and MultiMediaCard.
The Grand Tour Microphone jack A 3.5 mm mini microphone jack enables connection of a three-conductor mini jack for monaural microphone input, and connection of a stereo device for audio input. Headphone jack This jack lets you connect a stereo headphone (16 ohm minimum). When you connect headphones, the internal speaker is automatically disabled. Volume control Use this dial to adjust the volume of the internal stereo speakers and optional external stereo headphones (if connected).
The Grand Tour External monitor port This port allows you to connect an external monitor to the computer. LAN jack This jack lets you connect to a LAN. The adaptor has built-in support for Ethernet LAN (10 megabits per second, 10BASE-T) and Fast Ethernet LAN (100 megabits per second, 100BASE-TX). The LAN has two indicators. Refer to Chapter 4, Operating Basics, for details. HDMI out port HDMI out port can connect with Type A connector HDMI cable.One HDMI cable can send video and audio signals.
The Grand Tour The following figure shows the computers right side. 1. Universal Serial Bus (USB 2.0) port *2. Modem jack 3. Optical disc drive 4. DC IN 19V Jack 5. Security lock slot * Depending on the model you purchased. Figure 2-3 The right side of the computer Universal Serial Bus (USB 2.0) port Two Universal Serial Bus ports, which comply with the USB 2.0 standard, are provided on the right side of the computer.
The Grand Tour Optical disc drive The computer is configured with a DVD Super Multi drive. DC IN 19V Jack The AC adaptor connects to this jack in order to power the computer and charge its internal batteries. Please note that you should only use the model of AC adaptor supplied with the computer at the time of purchase - using the wrong AC adaptor can cause damage to the computer.
The Grand Tour The following figure shows the underside of the computer. You should ensure that the display is closed before the computer is turned over to avoid causing any damage. 1. Battery safety lock 2. Battery pack 3. Battery release latch 4. Cooling vents 5. Memory module slots 6. Hard disk drive Figure 2-5 The underside of the computer Users Manual Battery safety lock Slide this latch into its 'Unlock' position in order to release the battery pack and prepare for removal.
The Grand Tour Users Manual Memory module slots The memory module slots are located here. The memory module slots allow for the installation, replacement and removal of additional memory modules. Please refer to the Additional memory module section in Chapter 8, Optional Devices for more information. Hard disk drive The hard disk drive contains the main storage for the computer. Disk size varies depending on the model purchased.
The Grand Tour This section shows the computer with the display panel open. In order to open the display, lift the display panel up and position it at a comfortable viewing angle for you. *1. Web Camera LED *2. Web Camera *3. Microphone 4. Display screen 5. Display hinge 6. Stereo speakers 7. Touch Pad 8. Touch Pad control buttons 9. Power button 10. System indicators * Depending on the model you purchased.
The Grand Tour Users Manual Web Camera LED The Web Camera LED glows when the Web Camera is operating. Please remove the protective plastic-film before using the Web Camera. Web Camera The Web Camera is a device that allows you to record video or take photographs with your computer. You can use it for video chatting or video conferences using a communication tool such as Windows Live Messenger. TOSHIBA Web Camera Application will help you to add various video effects to your video or photograph.
The Grand Tour Keep foreign objects out of the speakers. Never allow metal objects, such as screws, staples and paper clips, to enter the computer or keyboard. Foreign metal objects can create a short circuit, which can cause computer damage and fire, possibly resulting in serious injury. Users Manual Touch Pad The Touch Pad mouse control device located in the center of the palm rest is used to control the movement of the on-screen pointer.
The Grand Tour The LED system indicators for specific computer operations glow when those operations are in progress. Figure 2-7 System indicators Users Manual Wireless communication The Wireless communication indicator glows amber when the Bluetooth and Wireless LAN functions are turned on. DC IN The DC IN indicator normally glows white when power is being correctly supplied from the AC power adaptor.
The Grand Tour The following figures show the positions of the CAPS LOCK indicator and the keypad overlay indicators which show the following conditions: When the CAPS LOCK indicator glows, the keyboard will produce capitals when any letter is typed. When the Arrow Mode indicator glows, the keypad overlay allows you to use cursor functions. When the Numeric Mode indicator glows, the keypad overlay allows you to enter numbers.
The Grand Tour The computer is configured with a DVD Super Multi drive. A Serial ATA interface controller is used for CD/DVD-ROM operation. When the computer is accessing a CD/DVD, an indicator on the drive glows. For further information on loading and unloading discs, please refer to the Writing CD/DVD on DVD Super Multi drives section in Chapter 4, Operating Basics. DVD Super Multi drives and their associated media are manufactured according to the specifications of six marketing regions.
The Grand Tour DVD-R, DVD+R, DVD-R (Dual Layer) and DVD+R (Double Layer) discs can be written only once. The recorded data cannot be erased or changed. DVD-RW, DVD+RW and DVD-RAM discs can be recorded more than once. Some types and formats of DVD-R (Dual Layer) and DVD+R (Double Layer) discs may be unreadable. The full-size DVD Super Multi drive module allows you to record data to recordable CD's and DVD's as well as run either 12cm (4.72") CD's, and DVD's, and 8cm (3.
The Grand Tour The AC adaptor can automatically adjust to any voltage ranging from 100 to 240 volts and to a frequency of either 50 or 60 hertz, enabling you to use this computer in almost any country/region. The adaptor converts AC power to DC power and reduces the voltage supplied to this computer. To recharge the battery, simply connect the AC adaptor to a power source and to the computer. Please refer to Chapter 6, Power and Power-up Modes for further information.
This chapter provides basic information to start using your computer. It covers the following topics: If the battery pack is not pre-installed in the computer that you purchased, please install the battery pack before you start using the computer. Please refer to Chapter 6-9, Replacing the battery pack for further information about installing the battery pack. All users should be sure to read the section Starting up for the first time.
Getting Started Use an anti-virus software and update it regularly. Never format storage media without checking its content - formatting destroys all stored data. It is a good idea to periodically back up the internal hard disk drive or other main storage device to external media. General storage media is not durable or stable over long periods of time and under certain conditions may result in data loss.
Getting Started Always use the TOSHIBA AC adaptor that was included with your computer or use AC adaptors specified by TOSHIBA to avoid any risk of fire or other damage to the computer. Use of an incompatible AC adaptor could cause fire or damage to the computer possibly resulting in serious injury. TOSHIBA assumes no liability for any damage caused by use of an incompatible adaptor.
Getting Started 1. Connect the power cord to the AC adaptor. Figure 3-1 Connecting the power cord to the AC adaptor (2-pin plug) Figure 3-2 Connecting the power cord to the AC adaptor (3-pin plug) Either a 2-pin or 3-pin adaptor/cord will be included with the computer depending on the model. 2. Connect the AC adaptor's DC output plug to the DC IN 19V jack on the right side of the computer. Figure 3-3 Connecting the adaptor to the computer 3.
Getting Started The display panel can be opened to a wide range of angles for optimal viewing. While holding down the palm rest with one hand so that the main body of the computer is not raised, slowly lift the display panel - this will allow the angle of the display panel to be adjusted to provide optimum clarity. Figure 3-4 Opening the display Use reasonable care when opening and closing the display panel. Opening it vigorously or slamming it shut could damage the computer.
Getting Started This section describes how to turn on the power - the Power indicator will then indicate the status. Please refer to the Monitoring of power condition section in Chapter 6, Power and Power-up Modes for more information. After you turn on the power for the first time, do not turn it off until you have set up the operating system. Please refer to the section Starting up for the first time for more information. Volume cannot be adjusted during Windows Setup. 1.
Getting Started The power can be turned off in one of three modes, either Shut Down Mode, Hibernation Mode or Sleep Mode. When you turn off the power in Shut Down Mode no data will be saved and the computer will boot to the operating system's main screen the next time it is turned on. 1. If you have entered data, either save it to the hard disk drive or to other storage media. 2. Make sure all disk/disc activity has stopped before removing the CD/DVD or floppy diskette.
Getting Started Benefits of Hibernation Mode The Hibernation Mode feature provides the following benefits: Saves data to the hard disk drive when the computer automatically shuts down because of a low battery condition. You can return to your previous working environment immediately when you turn on the computer. Saves power by shutting down the system when the computer receives no input or hardware access for the time period set by the System Hibernate feature.
Getting Started If you have to interrupt your work, you are able to turn off the power without exiting from your software by placing the computer into Sleep Mode. In this mode data is maintained in the computer's main memory so that when you turn on the power again, you can continue working right where you left off. When you have to turn off your computer aboard an aircraft or in places where electronic devices are regulated or controlled, always completely shut down the computer.
Getting Started Executing Sleep Mode You can also enable Sleep Mode by pressing FN + F3 - please refer to Chapter 5, The Keyboard, for further details. You can enter Sleep Mode in one of three ways: Click Start then click the arrow button ( button ( ) in the power management ) and select Sleep from the menu. Close the display panel. Please note that this feature must be enabled within the Power Options (to access it, click Start Control Panel System and Security Power Options). Press the power button.
Getting Started A hidden partition is allocated on the hard disk drive for the System Recovery Options. This partition stores files which can be used to repair the system in the event of a problem. The System Recovery Options feature will be unusable if this partition is deleted. The System Recovery Options feature is installed on the hard disk when shipped from the factory. The System Recovery Options menu includes tools to repair startup problems, run diagnostics or restore the system.
Getting Started This section describes how to create Recovery Media. Be sure to connect the AC adaptor when you create Recovery Media. Be sure to close all other software programs except the TOSHIBA Recovery Media Creator. Do not run software such as screen savers which can put a heavy load on the CPU. Operate the computer at full power. Do not use power-saving features. Do not write to the disc when the anti-virus software is running.
Getting Started A portion of the total hard disk drive space is configured as a hidden recovery partition. This partition stores files which can be used to restore pre-installed software in the event of a problem. If you subsequently set up your hard disk drive again, do not change, delete or add partitions in a manner other than specified in the manual, otherwise you may find that space for the required software is not available.
Getting Started 1. Load the Recovery Discs into the optical disc drive and turn off the computer's power. 2. While holding down F12 key on the keyboard, turn on your computer when TOSHIBA Leading Innovation>>> appears, release the F12 key. 3. Use the up and down cursor keys to select the CD-ROM icon from the menu. Please refer to the Boot Priority section in Chapter 7, HW Setup and Passwords for further information. 4. A menu will be displayed from which you should follow the on-screen instructions.
This chapter describes the basic operations of your computer and highlights the precautions that should be taken when using it. To use the Touch Pad, simply touch and move your fingertip across it in the direction you want the on-screen pointer to go. 1. TouchPad 2.
Operating Basics You can also tap the Touch Pad to perform functions similar to those of the left button on a standard mouse. Click: Tap once Double-click: Tap twice Drag and drop: Tap to select the item(s) you want to move, leave your finger on the Touch Pad after the second tap and then move the item(s) to their new destination. The full-size drive provides high-performance execution of CD/DVD-ROMbased programs. You can run either 12 cm (4.72") or 8 cm (3.15") CD/DVDs without an adaptor.
Operating Basics 2. Grasp the disc tray gently and pull until it is fully opened. Figure 4-3 Pulling the disc tray open 3. Lay the CD/DVD, label side up, in the disc tray. Figure 4-4 Inserting a CD/DVD When the disc tray is fully opened, the edge of the computer will extend slightly over the area where you insert the media. Therefore, when loading a CD or DVD, you will need to turn it slightly at an angle when you place it in the disc tray.
Operating Basics Do not touch either the laser lens or the area immediately around it doing so could cause misalignment and may damage the drive. Make sure that no foreign objects are inserted into or otherwise enter the drive. Check the disc tray, especially the area behind the front edge, to ensure that there are no foreign objects or material present before closing the drive. 4. Press the center of the CD/DVD gently until you feel it click into place on the center spindle.
Operating Basics 2. The CD/DVD media will extend slightly over the sides of the disc tray in order that you can hold it. Grasp it carefully by its edges and lift it vertically off of the central spindle and out of the tray. Figure 4-5 Removing a CD/DVD 3. Press the center of the disc tray in order to close it - the tray will click into place when it is locked.
Operating Basics The optical drive installed on this computer cannot write multiple sessions on DVD-R Dual Layer disc sessions. Once a disc has been written to once, it will be finalized. Once finalized, no further writing to the disc will be possible regardless of what portion of the total disc capacity was used. You can use the DVD Super Multi drive to write data to either CD-R, CDRW, DVD-R, DVD-R (Dual Layer), DVD-RW, DVD+R, DVD+R (Double Layer), DVD+RW, DVD-RAM, or DVD-R (Dual Layer) discs.
Operating Basics CD-R: TAIYO YUDEN CO., Ltd. MITSUBISHI KAGAKU MEDIA CO., LTD. Hitachi Maxell,Ltd. CD-RW: (Multi-Speed and High-Speed) MITSUBISHI KAGAKU MEDIA CO., LTD. CD-RW: (Ultra-Speed) MITSUBISHI KAGAKU MEDIA CO., LTD. DVD-R: DVD Specifications for Recordable Disc for General Version 2.0 TAIYO YUDEN Co.,Ltd. (for 8x and 16x speed media) MITSUBISHI KAGAKU MEDIA CO., LTD. (for 4x, 8x and 16x speed media) Hitachi Maxell,Ltd. (for 8x and 16x speed media) DVD-R (Dual Layer): MITSUBISHI KAGAKU MEDIA CO.
Operating Basics DVD+RW: MITSUBISHI KAGAKU MEDIA CO., LTD. (for 2.4x, 4x and 8x speed media) DVD-RAM: DVD Specifications for DVD-RAM Disc for Version 2.0, Version 2.1 or Version 2.2 Panasonic Electric Industrial Co.,Ltd. (for 3x and 5x speed media) Hitachi Maxell,Ltd.
Operating Basics Since the disc is based on the DVD standard, it might be filled with dummy data if the written data is less than about 1GB. Therefore, in these circumstance, even if you write only a small amount of data, it might take additional time to fill in the dummy data. When multiple drives that can write data to discs are connected, be sure that you do not write to or delete data from the wrong drive. Be sure to connect the AC adaptor to the computer before you write or rewrite any information.
Operating Basics Install, remove or connect external devices, including such items as a SD/SDHC memory card, miniSD/microSD Card, Memory Stick/Memory Stick PRO, MultiMediaCard, USB device, external monitor, or an optical digital device. Use the audio/video control button to reproduce music or voice. Open the optical disc drive. Do not use shut down, log off, Sleep Mode or Hibernation Mode functions while writing or rewriting.
Operating Basics Do not use the 'Disc Backup' function of TOSHIBA Disc Creator in order to copy DVD Video or DVD-ROM material that has copyright protection. DVD-RAM discs cannot be backed up using the 'Disc Backup' function of TOSHIBA Disc Creator. You cannot back up CD-ROM, CD-R or CD-RW media to DVD-R, DVDR (Dual Layer) or DVD-RW media using the 'Disc Backup' function of TOSHIBA Disc Creator.
Operating Basics Data Verification To verify that data has been written or rewritten correctly to a data CD/DVD you should follow the steps below before you begin the write/rewrite process: 1. Select Settings for Each Mode Data CD/DVD in the Setting menu. 2. Display the setting dialog box by one of the following two steps: Click the Recording settings button ( ) for writing on the main toolbar in the Data CD/DVD mode. Select Setting for Each Mode Data CD/DVD in the Setting menu. 3.
Operating Basics 4. Add source from HD Disk by click Add Video files button to invoke browser dialog box. 5. Choose the source video then go to Next page to apply Menu. 6. After choose the menu template, press Next button to go to Burning Page. 7. Choose the output type then press Burn button. How to learn more about Corel DVD MovieFactory® Please refer to the Help and Manual files for additional Corel DVD MovieFactory information.
Operating Basics Operate the computer for any other function, including using a mouse or Touch Pad, or closing/opening the display panel. Bump or cause vibration to the computer. Use the Mode control button and Audio/Video control button to reproduce music or voice. Open the DVD drive. Install, remove or connect external devices, including the following: SD/SDHC memory card, USB device, external display, optical digital devices. Please verify your disc after recording important data.
Operating Basics Screen savers will not display while playing a movie in the "TOSHIBA DVD PLAYER". The computer will also not go into Sleep Mode, Hibernation Mode or shutdown while using "TOSHIBA DVD PLAYER". Do not configure the Display automatic power off function to run while the "TOSHIBA DVD PLAYER" is running. Do not switch to Hibernation or Sleep Mode when running the "TOSHIBA DVD PLAYER".
Operating Basics Starting TOSHIBA DVD PLAYER Use the following procedure to start "TOSHIBA DVD PLAYER". 1. Insert an DVD-Video in the DVD Super Multi drive while Windows ® 7 is running. When an DVD-Video disc is set in the DVD drive, the following application selection screen may appear. If this occurs, select Play DVD movie, then click OK to launch the TOSHIBA DVD PLAYER. 2. Touch the CD/DVD panel on the Front operation panel. Or select Start All Programs TOSHIBA DVD PLAYER to start "TOSHIBA DVD PLAYER".
Operating Basics 7. If your CD's or DVD's become dusty or dirty, wipe them with a clean dry cloth from the center hole outwards - do not wipe in a circular direction. If necessary, you can use a cloth that has been lightly dampened in water or a neutral cleaner but you must not use benzine, thinner or any similar cleaning solution. The USB floppy diskette drive is available only as an option. 1. Store your floppy diskettes in the container they came in to protect them and keep them clean.
Operating Basics To launch Volume Mixer, follow the steps below. 1. Locate the Speaker icon on the task tray. 2. Right-click the Speaker icon on the task tray. 3. Select Open Volume Mixer from the menu. Click the Device button to display available playback devices. Select Speakers to use the internal speakers for listening. Adjust speaker volume by moving the slider up or down to raise or lower the volume. Click the Mute button to mute the sound.
Operating Basics Speaker Configuration Click the playback button to confirm the internal speakers or the headphone sound is coming from the right direction. Sound Effects This section explains how to select various sound effects. Environment - simulates reverberations of sound for familiar environments around us. You can select an existing preset in the menu. Equalizer - raises or lowers a frequency of sound to simulate a popular genre of music. You can select an existing preset in the menu.
Operating Basics 1. Microphone 2. Web Camera 3. Web Camera LED Figure 4-7 Web Camera Please unstick the protective plastic-film before using the Web Camera. Do not point the web camera directly at the sun. Do not touch or press strongly on the web camera lens. Doing so may reduce image quality. Use an eyeglass cleaner (cleaner cloth) or other soft cloth to clean the lens if it becomes dirty.
Operating Basics TOSHIBA Web Camera Application is pre-configured to start when you turn on Windows 7; if you need to restart it go to Start All Programs TOSHIBA Utilities Web Camera Application. 1. Capture Still Images 2. Open/Close Preview Area 3. Delete Recorded File 4. Video Recording 5. Camera Resolution 6. Capture Settings Figure 4-8 Using the Software Users Manual Capture Still Image Click to capture a still image, and see a preview of the captured image in preview area.
Operating Basics This feature uses a face verification library to verify the face data of users when they log in Windows. The user can thus avoid having to enter a password or the like, which makes the login process easier. TOSHIBA Face Recognition does not guarantee the correct identification of a user. Changes to the likeness of a registrant, such as hairstyle changes, wearing a cap, or wearing glasses may affect the recognition rates when such changes occur after the registrant had registered.
Operating Basics Take a picture for facial verification purposes, and register the data needed when you log in. To register the data needed when you log in, follow the steps as described below: 1. To launch this utility, click Start All Programs TOSHIBA Utilities Face Recognition. The Registration screen is displayed for a logged-in user whose face has not been registered. The Management screen is displayed for a logged-in user whose face has already been registered. 2.
Operating Basics 12. The Management screen is displayed. The registered account name will be displayed. Clicking on it will cause the captured image of your face to be displayed on the left. Delete image data, account information, and personal record data created during registration. To delete the Face Recognition Data, follow the steps as described below: 1. To launch this utility, click Start All Programs TOSHIBA Utilities Face Recognition. The Management screen is displayed. 2.
Operating Basics 6. Windows Welcome screen will be displayed, and will be logged in automatically to Windows. 1:1 Mode Login screen 1. Turn on the computer. 2. The Select Tiles screen will be displayed. 3. Select Start face recognition ( 4. 5. 6. 7. ). The Select Account screen will be displayed. Select the account, and click the Arrow button. "Please face the camera" will be displayed. Verification will be performed.
Operating Basics Telecommunication regulations vary from one region to another, so you will need to make sure the internal modems settings are correct for the region in which it will be used. The built-in modem can be used only in specified countries and regions. Using the modem in an area not specified for use may cause a system failure. Check the specified areas carefully before using it. To select a region, follow the steps as detailed below: 1.
Operating Basics Location list for region selection Displays a sub-menu appears which details location information. Open dialog box, if the modem and Telephony Current Location region code do not match Displays a warning if the current settings for both region code and telephony location are different. If the computer cannot recognize the internal modem, a dialog box is displayed from which you should select the appropriate communications port for your modem to use.
Operating Basics 2. Plug the other end of the modular cable into a telephone jack. Figure 4-9 Connecting the internal modem Do not pull on the cable or move the computer while the cable is connected. To disconnect the modular cable, follow the steps as detailed below: 1. Pinch the lever on the plug in the telephone jack and pull it out from within the connector. 2. Pinch the lever on the plug in the computer's modem jack and pull it out from within the computer.
Operating Basics The transmission speed over the wireless LAN, and the distance over which the wireless LAN can reach, may vary depending on surrounding electromagnetic environment, obstacles, access point design and configuration, client design and software/hardware configurations. The transmission rate described is the theoretical maximum speed as specified under the appropriate standard - the actual transmission speed will be lower than the theoretical maximum speed. 1.
Operating Basics The computer has built-in support for Ethernet LAN (10 megabits per second, 10BASE-T) and Fast Ethernet LAN (100 megabits per second, 100BASE-TX). This section describes how to connect/disconnect to a LAN. Do not install or remove a memory module while Wake-up on LAN is enabled. The Wake-up on LAN function consumes power even when the system is off. Leave the AC adaptor connected while using this feature.
Operating Basics Figure 4-10 Connecting the LAN cable 3. Plug the other end of the cable into a LAN hub connector or router. Check with your LAN administrator and hardware or software vendor before using or configuring a network connection. When the computer is exchanging data with the LAN, the LAN Active indicator glows yellow. When the computer is connected to a LAN hub but is not exchanging data, the Link indicator glows.
Operating Basics Some models include 1 cleaning cloth. The cleaning cloth can be used to wipe away dust and fingerprints from the keyboard and palm rest area of your computer. When wiping the keyboard, palm rest and display panel, do so gently without using excessive pressure. Do not use the cleaning cloth when it is dirty or wet. Do not use the cleaning cloth soaked with water, detergents or volatile organic solvents.
Operating Basics Always use a suitable carry case when transporting the computer. When carrying your computer, be sure to hold it securely so that it does not fall or hit anything. Do not carry your computer by holding any of its protruding elements. To protect from overheating, the CPU has an internal temperature sensor. If the computers internal temperature rises to a certain level, the cooling fan is turned on or the processing speed is lowered.
The computer's keyboard layouts are compatible with a 104/105-key enhanced keyboard - by pressing some keys in combination, all of the 104/105-key enhanced keyboard functions can be performed on the computer. The number of keys available on your keyboard will depend on which country/region your computer is configured for, with keyboards being available for numerous languages.
The Keyboard The function keys (not to be confused with the special FN key) are the twelve keys at the top of your keyboard - these keys function differently from other keys. F1 through F12 are called function keys because they execute programmed functions when pressed and, when used in combination with the FN key, those keys marked with icons also execute specific functions on the computer.
The Keyboard Press FN + F10 or FN + F11 to access the computer's integrated keypad. When activated, the keys with grey markings on their bottom edge become either numeric keypad keys (FN + F11) or cursor control keys (FN + F10). Please refer to the Keypad overlay section in this chapter for more information on how to operate these keys, taking care to note that the power on default for both settings is off. Press FN + F12 (ScrLock) to lock the cursor on a specific line. The power on default is off.
The Keyboard Sleep: Pressing FN + F3 switches the system to Sleep mode. Hibernate: Pressing FN + F4 switches the system to Hibernate mode. Output: Pressing FN + F5 changes the active display device. Brightness (Down): Pressing FN + F6 decreases the computer's display panel brightness in individual steps. Brightness (Up): Pressing FN + F7 increases the computer's display panel brightness in individual steps.
The Keyboard Zoom: Pressing FN + Space changes the display resolution. TOSHIBA Zooming Utility (reduce): Pressing FN + 1 reduces the icon size on the desktop or the font sizes within one of the supported application windows. TOSHIBA Zooming Utility (enlarge): Pressing FN + 2 enlarges the icon size on the desktop or the font sizes within one of the supported application windows.
The Keyboard Your computer's keyboard does not have a separate numeric keypad but includes a numeric keypad overlay which functions like one - this is located in the center of the keyboard with the relevant keys having grey letters at their front edge. The overlay provides the same functions as the numeric keypad on a standard 104/105-key enhanced keyboard. The numeric keypad overlay can be used for numeric data input or cursor and page control.
The Keyboard While using the overlay, you can temporarily access the normal keyboard functions without having to turn the overlay off: 1. Hold FN and press any other key - this key will operate as if the overlay were off. 2. Type upper-case characters by holding FN + SHIFT and pressing a character key. 3. Release FN to continue using the selected overlay function. While using the normal keyboard function, you can temporarily use the keypad overlay without having to turn it on: 1. Press and hold down FN.
The computer's power resources include the AC adaptor and internal batteries. This chapter gives details on making the most effective use of these resources including charging and changing batteries, tips for saving battery power, and power-up modes. The computer's operating capability and battery charge status are affected by different power conditions, including whether an AC adaptor is connected, whether a battery pack is installed and what the charge level is for that battery.
Power and Power-up Modes Table 6-1 Power conditions continued Power on AC adaptor not connected Battery charge is above low battery trigger point Operates LED: Battery off DC IN off Battery charge is below low battery trigger point Operates LED: Battery flashes Amber DC IN off Battery charge is exhausted Computer goes into Sleep Mode and shuts down No battery installed Cannot operate LED: Battery off DC IN off Power off (no operation) As shown in the below table, the Battery, DC IN an
Power and Power-up Modes Check the DC IN indicator to determine the power status with the AC adaptor connected - the following indicator conditions should be noted: Green Indicates the AC adaptor is connected and is correctly supplying power to the computer. No light Under any other conditions, the indicator does not light.
Power and Power-up Modes The battery pack is a lithium ion battery, which can explode if not properly replaced, used, handled or disposed of. Dispose of the battery as required by local ordinances or regulations. Use only batteries recommended by TOSHIBA as replacements. Do not remove the battery pack while the computer is in Sleep Mode. In this mode data is stored in memory, so if the computer loses power, it will be lost.
Power and Power-up Modes The battery pack is a vital component of portable computing and, as such, taking proper care of it will help ensure a longer operating time on battery power as well as deliver a longer life for your battery pack. The instructions detailed in this section will help to ensure safe operation and maximum performance. Refer to the enclosed Instruction Manual for Safety and Comfort for detailed precautions and handling instructions.
Power and Power-up Modes Use only the computer connected to an AC power source or the optional TOSHIBA Battery charger to charge the battery pack. Never attempt to charge the battery pack with any other charger. Time The following table shows the approximate time required to fully charge a discharged battery.
Power and Power-up Modes Repeat these steps two or three times until the battery recovers normal capacity. Remaining battery power can be monitored using the following methods. Clicking the battery icon on the task bar Via the Battery Status in the Windows Mobility Center window You should wait at least 16 seconds after turning on the computer before trying to monitor the remaining operating time.
Power and Power-up Modes When you turn off your computer with fully charged batteries, the batteries retain data for the following approximate time periods. Retention Time Battery type State and Retention Time Battery pack 1 day for 6 cell, 0.
Power and Power-up Modes Please be aware that the battery pack is classified as a consumable item. The operating life of the battery pack will gradually reduce through repeated charging and discharging, and will need to be replaced when it reaches the end of its operating life. In addition to this, you might also replace a discharged battery pack with a charged spare when you are operating your computer away from an AC power source for an extended period of time.
Power and Power-up Modes 5. Slide the battery safety lock towards the release ( the battery release latch movable. ) position to make Figure 6-1 Releasing the battery pack (1) 6. Slide and hold the battery release latch (1) to disengage the battery pack and then remove it from the computer (2).
Power and Power-up Modes To install a battery, follow the steps as detailed below: 1. Insert the battery pack as far as it will go into the computer (1). 2. Ensure that the battery pack is securely in place and the battery safety lock (2) is in its position. Figure 6-3 Securing the battery pack 3. Turn your computer over.
Power and Power-up Modes The TOSHIBA Supervisor Password Utility provides two levels of password security: User and Supervisor. Passwords set in TOSHIBA Supervisor Password Utility are different from the Windows® login password. To start the utility, point to or click the following items: Launch TOSHIBA Assist SECURE User Password Registered Click to register a password of up to 8 characters. After a password is set, you will be prompted to enter it when you start the computer.
Power and Power-up Modes 2. Enter the Password. 3. Press Enter. If you enter the password incorrectly three consecutive times, the computer shuts down. You must turn on the computer again and re-enter the password.
This chapter explains how to use TOSHIBA HW Setup program to configure your computer and how to set passwords. TOSHIBA HW Setup allows you to configure settings for General, Password, Display, Boot Priority, Keyboard, USB and LAN. If the supervisor password is set, access to the TOSHIBA HW Setup program can be prevented when the user password is used to log on to the computer. Click on Start All Programs TOSHIBA Utilities HWSetup.
HW Setup and Passwords General This window displays the BIOS version and contains two buttons: Default Return all HW Setup values to the factory settings. About Display the HW Setup version. Setup This field displays BIOS Version and date. When finish BIOS update, please restart your computer and press F2 into BIOS setup manual and load BIOS default one time. Password User Password This option allows you to set or reset the user password for power on. Not Registered Changes or remove the password.
HW Setup and Passwords Not registered If they do not match, the following message appears. You must repeat step 1. Incorrect Password!!! If you enter the password incorrectly three times in a row, the computer will shut down. You will not be able to access the password option in the HW Setup. In this case you must turn the power off and back on to retry the procedure. 4. Follow the same procedures described in the earlier section, How to set the password, to set a new user password.
HW Setup and Passwords Keyboard Wake-up on Keyboard When this feature is enabled and the computer is in Sleep mode, you can turn on the computer by pressing any key. It is effective only for the internal keyboard and only when the computer is in Sleep mode. Enabled Enables the Wake-up on Keyboard feature. Disabled Disables the Wake-up on Keyboard function (Default). USB Legacy USB Support Use this option to enable or disable USB Legacy Emulation.
Optional devices can expand the computer's capabilities and its versatility. This chapter describes the connection or installation of the following devices: To connect optional devices (such as USB device or External monitor) to the computer, be sure to check the shape and orientation of the connector before connecting.
Optional Devices The computer is equipped with a bridge media slot that can accommodate some kinds of memory media with various memory capacities so that you can easily transfer data from devices, such as digital cameras and Personal Digital Assistants. Keep foreign objects out of the bridge media slot. Never allow metal objects, such as screws, staples and paper clips, to enter the computer or Keyboard.
Optional Devices Below is a simple explanation for distinguishing SD memory cards from SDHC memory cards. SD and SDHC memory cards appear the same externally. The logo on SD and SDHC memory cards is different, so pay careful attention to the logo when purchasing. The SD memory card logo is ( ). The SDHC memory card logo is ( ). The maximum capacity of SD memory cards is 2GB. The maximum capacity of SDHC memory cards is 16G.
Optional Devices Use only memory modules approved by TOSHIBA. Do not try to install or remove a memory module under the following conditions. a. The computer is turned on. b. The computer was shut down in either Sleep or Hibernation Mode. c. Wake-up on LAN is enabled. d. The wireless communication switch is turned on. Be careful not to let screws or other foreign matter fall into the computer. It could cause malfunction or electric shock.
Optional Devices 3. Turn the computer upside down and remove the memory module cover. 1. Memory module cover 2. Screw 3. Slot A 4. Slot B Figure 8-2 Removing the memory module cover 4. Align the notch of the memory module with that of the memory module slot and gently insert the module into the slot at about a 45 degree angle before holding it down until the latches on either side snap into place.
Optional Devices 5. Seat the memory module cover in place and secure it with one screw. Take care to ensure that the memory module cover is firmly closed. Figure 8-3 Seating the memory module cover 6. Install the battery pack - refer to Replacing the battery pack section in Chapter 6, Power and Power-up Modes, if required. 7. Turn your computer over. 8. Turn the computer on and make sure the added memory is recognized to confirmed it, Start Control Panel System and Security System icon.
Optional Devices 5. Grasp the memory module by its edges and remove it from the computer. If you use the computer for a long time, the memory modules and the circuits locating close to the memory modules will become hot. In this case, let them cool to room temperature before you replace them.Or you will get burnt if you touch any of them. Do not touch the connectors on the memory module or on the computer. Debris on the connectors may cause memory access problems. 6.
Optional Devices 1. USB connector 2. Disk-In-Use Indicator 3. Floppy diskette slot 4. Eject button Figure 8-4 USB floppy diskette drive USB connector Insert this connector into one of the free USB ports of your computer. Disk-In-Use Indicator This indicator glows when the floppy diskette is being accessed. Floppy diskette slot Insert a floppy diskette into this slot. Eject button When a floppy diskette is fully seated in the drive, the eject button will pop out.
Optional Devices The USB floppy diskette drive accommodates either a 1.44MB or 720KB floppy diskette and connects to one of the computer's USB ports. Connecting the USB floppy diskette drive To connect the drive, plug the floppy diskette drive's USB connector into one of the computer's free USB ports. Make sure the connector is right side up and properly aligned with the socket. Do not try to force the connection; doing so can damage the connecting pins.
Optional Devices An external analog monitor can be connected to the computer's external monitor port, with the computer supporting WUXGA video mode. In order to connect a monitor, follow the steps as detailed below: 1. Turn the computer's power off. 2. Connect the monitor cable to the external monitor port and tighten the screws on the left and right hand side of the connector as required. Figure 8-6 Connecting the monitor cable to the external monitor port 3. Turn the external monitors power on. 4.
Optional Devices As the port operation of all HDMI (High-Definition Multimedia Interface) monitors have not been confirmed, some HDMI monitors may not function properly. When you connect a television or external monitor to the HDMI port and the display output device is set to HDMI. When you unplug the HDMI cable and re-plug it in please wait at least 5 seconds before you replug the HDMI cable again.
Optional Devices To view video on the HDMI device, be sure to configure the following settings otherwise you may find that nothing is displayed. Be sure to use the FN + F5 HotKey to select the display device before starting to play video. Do not change the display device while playing video. Do not change the display device under the following conditions. While data is being read or written. While communication is being carried out. To select the display mode, follow the steps as detailed below: 1.
Optional Devices Using REGZA Link (PC Control) Toshiba notebooks with REGZA Link include a Toshiba utility dedicated to take advantage of its capabilities which can allow you to: Use the TV remote control to output the computer screen onto the TV screen. Use the TV remote control to launch, operate and close applications on your computer. Turn on the TV when the HDMI output is selected using the Fn + F5 key. Switch the video output (HDMI or LCD) when executing certain desktop icons.
TOSHIBA have designed this computer for durability, however, should problems occur you are able to use the procedures detailed in this chapter to help determine the cause. All users should become familiar with this chapter as knowing what might go wrong can help prevent problems from occurring in the first place.
Troubleshooting You should always consider the simplest solution first - the items detailed in this checklist are easy to fix and yet may cause what appears to be a serious problem: Make sure you turn on all peripheral devices before you turn on the computer - this includes your printer and any other external device you are using. Before you attach an external device you should first turn the computer off, then when you turn the computer back on again it will recognize the new device.
Troubleshooting Do you hear any beeps? If so, how many, are they long or short, and are they high pitched or low pitched? In addition, is the computer making any unusual noises? Write down what you hear. Record your observations so you can describe them in detail to your reseller, dealer or service provider. Software Hardware The problems may be caused by your software or disk.
Troubleshooting When the computer does not start properly, check the following items: Self Test Power Sources Power-on Password While booting up the computer, self test is executed automatically and the following will be displayed: TOSHIBA Leading Innovation>>> This message remains on the screen for a few seconds. If the self test is successful, the computer tries to load the operating system according to how the Boot Priority option is set within the TOSHIBA HW Setup program.
Troubleshooting Overheating power down If the processor's temperature reaches an unacceptably high level with either setting, the computer will automatically shut down to prevent any damage - in this instance all unsaved data in memory will be lost. Problem Procedure Computer shuts down and DC IN indicator blinks white Leave the computer off until the DC IN indicator stops blinking.
Troubleshooting Battery If you suspect a problem with the battery, you should check the status of the DC IN indicator as well as the Battery indicator. Please refer to Chapter 6, Power and Power-up Modes for more information on these indicators, together with general battery operation. Problem Procedure Battery doesnt power the computer The battery may be discharged - connect the AC adaptor to recharge the battery.
Troubleshooting Real Time Clock Problem Procedure The following message is displayed on the LCD: RTC battery is low or CMOS checksum is inconsistent. Press [F2] key to set Date/Time. The RTC battery charge has become exhausted, you should set the date and time in within the BIOS setup screen through the following steps: 1. Press [F2] key. BIOS setup will boot up. 2. Press [F2] to set the date in [System Date]. 3. Press [F2] to set the time in [System Time].
Troubleshooting Problem Procedure No display Press the FN + F5 hot keys to adjust the display priority, and to make sure it is not set for output to an external monitor. Markings appear on the These marks may have come from contact with LCD screen. the keyboard, or Touch Pad while the display has been closed. You should try to remove the marks by gently wiping the display panel with a clean dry cloth or, if this fails, with a good quality LCD screen cleaner.
Troubleshooting Problem Procedure Slow performance The files on the hard disk drive may be fragmented - in this instance you should run the disk Defragmentation utility to check the condition of your files and the hard disk drive. Please refer to the operating system's documentation or online Help File for further information on operating and using the Defragmentation utility. As a last resort you should reformat the hard disk drive and then reload the operating system and all other files and data.
Troubleshooting For further information, please refer to Chapter 4, Operating Basics. Problem Procedure You cannot access a CD/DVD in the drive Make sure the drive's disc tray is securely closed press it gently into the computer until it clicks into place. Open the drive's disc tray and ensure the CD or DVD is properly seated - it should lie flat with the label facing upwards.
Troubleshooting USB floppy diskette drive The USB floppy diskette drive is available only as an option. For further information, please refer to Chapter 4, Operating Basics. Problem Procedure Drive does not operate Check the connection between the computer and the drive to ensure that it is properly attached.
Troubleshooting For further information, please refer to Chapter 8, Optional Devices. Problem Procedure Memory Stick/Memory Stick PRO error occurs Remove the Memory Stick/Memory Stick PRO from the computer and then reinsert it in order to ensure it is firmly connected. If the problem persists, then you should refer to the documentation supplied with your Memory Stick/Memory Stick PRO for further information.
Troubleshooting Touch Pad Users Manual Problem Procedure On-screen pointer does not respond to pointing device operation In this instance the system might be busy - Try moving the mouse again after waiting a short while. Double-tapping does not work In this instance, you should initially try changing the double-click speed setting within the Mouse Control utility. 1. To access this utility, click Start Control Panel Hardware and Sound Mouse icon. 2.
Troubleshooting USB mouse Problem Procedure On-screen pointer does not respond to mouse operation In this instance the system might be busy - Try moving the mouse again after waiting a short while. Remove the mouse from the computer and then reconnect it to a free USB port it in order to ensure it is firmly attached. Users Manual Double-clicking does not work In this instance, you should initially try changing the double-click speed setting within the Mouse Control utility. 1.
Troubleshooting In addition to the information in this section, please also refer to the documentation supplied with your USB device. Problem Procedure USB device does not work Remove the USB device from the computer and then reconnect it to a free port in order to ensure it is firmly attached. Ensure that any required USB device drivers are properly installed - to achieve this you should refer to both the device documentation and the operating system documentation.
Troubleshooting Problem Procedure An error will occur if a memory module is inserted into Slot B while no memory module is inserted in Slot A. Remove the memory module from Slot B and insert it into Slot A. In addition to the information in this section, please also refer to the documentation supplied with your audio device. Problem Procedure No sound is heard Adjust the volume control. Turn the dial clockwise to decrease the volume and turn it counter-clockwise to increase the volume.
Troubleshooting Problem Procedure No sound is heard Adjust the volume control. Turn the dial clockwise to increase the volume and turn it counter-clockwise to decrease the volume. Turn the volume control while verifying the volume in order to adjust. Annoying sound is heard Volume cannot be adjusted when Windows is turned on or turned off. If you are still unable to resolve the problem, contact your reseller, dealer or service provider.
Troubleshooting Problem Procedure No display Try adjusting the contrast and brightness controls on the external monitor. Press the FN + F5 hot key in order to change the display priority and ensure that it is not set for the internal display panel only. Check to see if the external monitor is connected.
Troubleshooting Users Manual Problem Procedure You place a call, but a connection cant be made Make sure that the settings are correct within your communication application. After making a call you cant hear a ring Ensure that the communication application's tone or pulse dialling selection feature is set correctly.
Troubleshooting If the following procedures do not restore LAN access, consult your LAN administrator. For more information on wireless communication, refer to Chapter 4, Operating Basics. Problem Procedure Cannot access Wireless LAN Make sure the computers wireless communication switch is set to on. Problem Procedure No display Try adjusting the contrast and brightness controls on the television.
Troubleshooting Problem Procedure DVD does not play smoothly when using the Windows Media Center of the DVD playing software Try setting the configuration in the BIOS setup. However, note that when the BIOS setup configuration is modified, the power saving function of PCI Express becomes disabled. Refer to Chapter 7, HW Setup and Passwords for more information. Set the PCI Express Link ASPM in the BIOS setup using the following steps: 1. Press the F1 key. The BIOS setup screen will appear. 2.
Troubleshooting If you are still unable to solve the problem and suspect that it is hardware related, write to TOSHIBA at the nearest location listed below: Users Manual Outside of Europe In Europe Australia TOSHIBA Australia Pty Ltd. Information Systems Division Building C, 12-24 Talavera Rd, North Ryde, 2113, NSW, Australia Germany & Austria TOSHIBA Europe (I.E.) GmbH Geschäftsbereich, Deutschland-Österreich Hammfelddamm 8, D-41460 Neuss, Germany Canada TOSHIBA of Canada Ltd.
This chapter slates the Disclaimer(s) information applicable to TOSHIBA computers. Central Processing Unit ("CPU") Performance Disclaimer.
Disclaimers Under some conditions, your computer product may automatically shutdown. This is a normal protective feature designed to reduce the risk of lost data or damage to the product when used outside recommended conditions. To avoid risk of lost data, always make back-up copies of data by periodically storing it on an external storage medium. For optimum performance, use your computer product only under recommended conditions.
Disclaimers Battery life may vary considerably depending on product model, configuration, applications, power management settings and features utilized, as well as the natural performance variations produced by the design of individual components. Published battery life numbers are achieved on select models and configurations tested by Toshiba at the time of publication. Recharge time varies depending on usage. Battery may not charge while computer is consuming full power.
Disclaimers The actual transmission speed will be lower than the theoretical maximum speed. New wireless network adapter "AR9281, AR9283, AR9285, and RTL8191SE" supports IEEE802.11b/g/draft-n but does not support IEEE02.11a. The wireless adapter is based on a draft 2.0 release version of the IEEE 802.11n specification and; may not be full compatible with, or support some feature (e.g., security) of, certain Wi-Fi equipment. One Gigabyte (GB) means 109 =1,000,000,000 bytes using powers of 10.
Appendixes Table of Contents Appendix A Specifications 1 Appendix B Display Controller 1 Appendix C V.90/V.
This appendix summarizes the computers technical specifications.
The ability of this feature is depending on the model you purchased. Network control unit (NCU) Type of NCU AA Type of line Telephone line (analog only) Type of dialing Pulse Tone Control command AT commands EIA-578 commands Monitor function Computers speaker Communication specifications Users Manual Communication system Data: Fax: Communication protocol Data ITU-T-Rec (Former CCITT) Bell Fax ITU-T-Rec (Former CCITT) Full duplex Half duplex V.21/V.22/V.22bis/V.32/V.32 bis/V.34/V.
The display controller interprets software commands into hardware commands that turn particular pixels on or off. A high-resolution external monitor connected to the computer can display up to 2048 horizontal and 1536 vertical pixels at up to 16M colors. The display controller also controls the video mode, which uses industry standard rules to govern the screen resolution and the maximum number of colors that can be displayed on screen.
The TOSHIBA internal modem uses V.90 technology. The modem is capable of downstream speeds of 56Kbps (kilobits per second) when connected to an Internet service provider that supports V.90/V.92. As with any modem, the actual throughput (speed of data transfer) depends on analog telephone line conditions, which can vary considerably. Therefore, many users will experience throughput in the range of 32-44Kbps under normal telephone line conditions. Upstream data flows at the V.34 rate. V.
Table Result codes for a V.90 connection No.
-V90=* V.90 Dial Line Rate -V90 sets the maximum V.90 downstream that the modem attempts to connect Users Manual -V90=0 V.90 disabled -V90=1 V.
This appendix is intended to help you get your Wireless LAN network up and running, with a minimum of parameters. Form Factor Mini Card Compatibility IEEE 802.11 Standard for Wireless LANS Wi-Fi (Wireless Fidelity) certified by the Wi-Fi Alliance. The Wi-Fi CERTIFIED logo is a certification mark of the Wi-Fi Alliance.
Radio Characteristics of Wireless LAN Cards may vary according to: Country/region where the product was purchased Type of product Wireless communication is often subject to local radio regulations. Although Wireless LAN wireless networking products have been designed for operation in the license-free 2.4GHz and 5GHz band, local radio regulations may impose a number of limitations to the use of wireless communication equipment.
Table Wireless IEEE 802.11 Channels Sets (Revision B and G) Frequency Range Channel ID 2400-2483.5 MHz 1 2412 2 2417 3 2422 4 2427 5 2432 6 2437 7 2442 8 2447 9 2452 10 2457*1 11 2462 12 2467*2 13 2472*2 When installing Wireless LAN cards, the channel configuration is managed as follows: For wireless clients that operate in a Wireless LAN infrastructure, the Wireless LAN card will automatically start operation at the channel identified by the Wireless LAN Access Point.
Table Wireless IEEE 802.
*1 Factory-set default channels *2 Refer to the sheet Approved Countries/Regions for use for the countries/regions that in which these channels can be used. *3 These channels are available to A/B/G combo type only. *4 Available Area: US (USA, CANADA) only.
The AC input plug of power cord must be compatible with various international AC power outlets. Power cords need to meet the local standards and the specifications listed as below: Users Manual Length: Minimum 1.7 meters Wire size: Minimum 0.75 mm2 Current rating: Minimum 2.
Europe: Austria: OVE Italy: IMQ Belgium: CEBEC The Netherlands: KEMA Denmark: DEMKO Norway: NEMKO Finland: FIMKO Sweden: SEMKO France: LCIE Switzerland: SEV Germany: VDE United Kingdom: BSI Outside of Europe: U.S. and Canada: UL listed and CSA certified No. 18 AWG, Type SVT or SPT-2 China: CCC, CQC Australia: AS India: STQC In Europe, two conductors power cord must be VDE type, H05VVH2-F or H03VVH2-F and for three conductors power cord must be VDE type, H05VV-F.
USA Australia Canada Users Manual United Kingdom Europe China E-3
The terms in this glossary cover topics related to this manual. Alternate naming is included for reference.
Glossary IDE: integrated drive electronics IEEE: Institute of Electrical and Electronics Engineers I/O: input/output IrDA: Infrared Data Association IRQ: interrupt request KB: kilobyte LAN: local area network LCD: liquid crystal display LED: light emitting diode MB: megabyte MMC: multi media card OCR: optical character recognition (reader) PCB: printed circuit board PCI: peripheral component interconnect RAM: random access memory RGB: red, green, and blue ROM: read only memory RTC: real time clock S/P DIF:
Glossary analog signal: A signal whose characteristics such as amplitude and frequency vary in proportion to (are an analog of) the value to be transmitted. Voice communications are analog signals. application: A group of programs that together are used for a specific task such as accounting, financial planning, spreadsheets, word processing and games. ASCII: American Standard Code for Information Interchange.
Glossary cache memory: A section of very fast memory in which frequently used information is duplicated for quick access. Accessing data from cache is faster than accessing it from the computer's main memory. See also L1 cache, L2 cache. capacity: The amount of data that can be stored on a magnetic storage device such as a floppy diskette or hard disk drive.
Glossary Composite Video (YUV): A standard video signal used to transmit images, e.g. from a VCR to a TV. computer program: A set of instructions written for a computer that enable it to achieve a desired result. computer system: A combination of hardware, software, firmware, and peripheral components assembled to process data into useful information. configuration: The specific components in your system (such as the terminal, printer, and disk drives) and the settings that define how your system works.
Glossary disk drive: The device that randomly accesses information on a disk and copies it to the computer°¶s memory. It also writes data from memory to the disk. To accomplish these tasks, the unit physically rotates the disk at high speed past a read-write head. disk storage: Storing data on magnetic disk. Data is arranged on concentric tracks much like a phonograph record. display: A CRT, LCD, or other image producing device used to view computer output.
Glossary enable: To turn on a computer option. See also disable. erase: See delete. escape: 1) A code (ASCII code 27), signaling the computer that what follows are commands; used with peripheral devices such as printers and modems. 2) A means of aborting the task currently in progress. escape guard time: A time before and after an escape code is sent to the modem which distinguishes between escapes that are part of the transmitted data, and escapes that are intended as a command to the modem.
Glossary hard disk: A storage device composed of a rigid platter or platters that can be magnetically coded with data. Hard disks hold much more information than diskettes and are used for long-term storage of programs and data. The primary (or only) hard disk in a computer is usually fixed, but some computers have secondary hard disks that are removable. By default, the hard disk is referred to as drive C. hard disk drive (HDD): An electromechanical device that reads and writes a hard disk.
Glossary K: Taken from the Greek word kilo, meaning 1000; often used as equivalent to 1024, or 2 raised to the 10th power. See also byte and kilobyte. keyboard: An input device containing switches that are activated by manually pressing marked keys. Each keystroke activates a switch that transmits a specific code to the computer. For each key, the transmitted code is, in turn, representative of the (ASCII) character marked on the key. kilobyte (KB): A unit of data storage equal to 1024 bytes.
Glossary mode: A method of operation, for example, the Shut Down Mode, Sleep Mode or the Hibernation Mode. modem: Derived from modulator/demodulator, a device that converts (modulates) digital data for transmission over telephone lines and then converts modulated data (demodulates) to digital format where received. monitor: A device that uses rows and columns of pixels to display alphanumeric characters or graphic images. See also CRT.
Glossary PAL: PAL (Phase Alternating Line) is the dominant video and broadcasting standard in Europe. parity: 1) The symmetrical relationship between two parameter values (integers) both of which are either on or off; odd or even; 0 or 1. 2) In serial communications, an error detection bit that is added to a group of data bits making the sum of the bits even or odd. Parity can be set to none, odd, or even. password: A unique string of characters used to identify a specific user.
Glossary Random Access Memory (RAM): Volatile memory that can be written to as well as read. Volatile here means that information in RAM is lost when you turn off your computer. This type of memory is used for your computer's main memory. See also memory. Compare ROM. resolution: A measure of the sharpness of the images that can be produced by a printer or displayed on a screen. For a printer, resolution is expressed in dots per inch (dpi).
Glossary system disk: A diskette that contains the operating system files needed to start the computer. Any diskette can be formatted as a system disk. A system disk is also called a "bootable disk", "boot disk" or a "startup disk." Compare non-system disk. terminal: A typewriter-like keyboard and CRT display screen connected to the computer for data input/output.
AC adaptor, 1-5 additional, 1-15 connecting, 3-2 DC IN 19V jack, 2-5 ASCII characters, 5-7 Battery charging, 6-5 extending battery life, 6-8 indicator, 2-11, 6-2 Monitoring capacity, 6-7 real time clock, 1-5, 6-4 save mode, 1-10 types, 6-3 Battery Charger, 8-7 Battery pack, 1-5, 2-6 additional, 8-7 replacing, 6-9 Bridge media slot, 1-5, 2-1, 8-2 indicator, 2-11 using, 8-2 Cache memory, 1-3 Cleaning the computer, 4-31 Cooling vents, 2-2, 2-6 DC IN indicator, 2-11, 6-3 Display, 2-8 automatic power off, 1-9 Us
Hard disk drive automatic power off, 1-9 HDMI, 8-10 Heat dispersal, 1-10 Hibernation Mode, 1-10 Hot keys, 1-9 Brightness (Down), 5-4 Brightness (Up), 5-4 Hibernate, 5-4 Lock, 5-3 Mute, 5-3 Output, 5-4 Power Plan, 5-3 Sleep, 5-4 TOSHIBA Zooming Utility (enlarge), 5-5 TOSHIBA Zooming Utility (reduce), 5-5 Touch Pad, 5-4 Wireless, 5-4 Zoom, 5-5 HW Setup accessing, 7-1 general, 7-2 HW Setup utility, 1-12 Keypad overlay, 1-10, 5-6 arrow mode, 5-6 numeric mode, 5-6 temporarily using normal keyboard (overlay on),
USB, 1-5 Power conditions, 6-1 Hibernation Mode, 3-7 indicator, 6-3 panel power on/off, 6-13 Shut Down mode (Boot Mode), 3-7 Sleep Mode, 3-9 system auto off, 6-13 turning off, 3-7 turning on, 3-6 Problems AC power, 9-5 Analyzing the problem, 9-2 Battery, 9-6 External monitor, 9-17 Hard disk drive, 9-8 Hardware and system checklist, 9-3 HDMI Monitor, 9-20 Internal display panel, 9-7 Keyboard, 9-7 LAN, 9-19 Memory Stick/Memory Stick PRO, 9-12 Modem, 9-18 MultiMediaCard, 9-12 Overheating power down, 9-5 Passwo
Video RAM, 1-4 Volume control, 2-2 Web Camera, 1-6 Wireless communication, 4-28 indicator, 4-29 Wireless LAN, 1-6, 4-28 problems, 9-20 Users Manual Index-4
