OWNER'S MANUAL DLP Projection Television TM Owner's Record The model number and serial number are on the back of your TV. Record these numbers in the spaces below. Refer to these numbers whenever you communicate with your Toshiba dealer about this TV. 44HM85 5 Model: Serial No.
562C_2~5(2)_en 90/6/18 1:15 PM Page 2 Dear Customer, Thank you for purchasing this Toshiba TV. This manual will help you use the many exciting features of your new TV. Before operating the TV, please read this manual completely, and keep it nearby for future reference. Safety Precautions WARNING TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE.
562C_2~5(2)_en 90/6/18 1:15 PM Page 3 Important Safety Instructions 1) 2) 3) 4) Read these instructions. Keep these instructions. Heed all warnings. Follow all instructions. 5) Do not use this apparatus near water. 6) Clean only with a dry cloth. 7) Do not block any ventilation openings. Install in accordance with the manufacturer’s instructions. 8) Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers) that produce heat.
562C_2~5(2)_en 90/6/18 1:15 PM Page 4 Installation (cont. from previous page) Care (cont. from previous column) 27) Always make sure the antenna system is properly grounded to provide adequate protection against voltage surges and built-up static charges (see Section 810 of the National Electric Code).
62C_2~5(2)_en 90/6/18 1:15 PM Page 5 TM Important notes about your DLP projection TV 1) The light source for this TV is a projection lamp unit with a limited service life. When the lamp wears out, the picture may become dark or black, or the lamp may fail, at which time you must replace the lamp unit. See “Lamp unit replacement” on pages 46-48. 5) Always sit approximately 10–25 feet away from the TV and as directly in front of it as possible.
Table of Contents Important Safety Instructions .TM. . . . . . . . . . . . . . . .2-4 Important notes about your DLP projection TV . . . . . . .5 Welcome to Toshiba . . . . . . . . . . . . . . . . . . . . . . . . .7 Function Status Indicators . . . . . . . . . . . . . . . . . . . . .7 Step 1. Hook Up TV Rear Connections Panel . . . . . . . . . . . . . . . . . . . . . . .8 Front Connections Panel . . . . . . . . . . . . . . . . . . . . . .9 ANT/Cable Service Hookup . . . . . . . . . . . . . . . . . . . .
Welcome to Toshiba Welcome to Toshiba Congratulations! You have purchased one of the finest DLPTM projection TVs on the market. The goal of this manual is to guide you through setting up and operating your Toshiba TV as quickly as possible. This manual applies to models 44HM85. The model and serial numbers are on the back of your TV. Write these numbers in the space provided on the front cover of this manual for your records. Instructions in this manual are based on using the remote control.
Rear Connections Panel Connecting cables and external equipment to your TV.
Front Connection Panel There are four jacks on the left side on your projection TV that make connecting Audio/Video devices like video games and camcorders very simple. The jacks are like those found on the back jack connection panel. This means that most equipment that connects to those types of jacks on the rear jackpack, may be connected to the front connection panel. To use the front jacks as the signal source, select them using Main Input menu as described on page 44.
ANT / Cable Service Hookup 1 Connect an antenna or cable service to your TV as shown. 2 Turn to page 23 to do a channel search with Auto program for Ant/Cable connection(s).
Cable Box Connections 1 Cable TV Wall Jack Panel Locate the output jack on the back of your cable box. Connect this to the Antenna jack on the back of your TV. Or find the composite video and audio jacks on the back of your cable box, and connect them following the instructions provided with your equipment. This can be combined with any other equipment you may want to hook up.
VCR Connections Locate the Antenna jack on the back of your TV. Connect this to RF out jack on the back of your VCR. 1 Or, find the composite video and audio jacks on the back of your VCR, and connect them following the instructions provided with your equipment. You may connect either the composite video or the S-Video cables to your TV. (Do not connect both the composite and the S-Video cables. In the event that you connect both composite and the SVideo cables, only the S-Video will work.
DVD Player 1 Find the audio and ColorStream HD or S-Video jacks on the back of your DVD Player and connect them following the instructions provided with your equipment. You may connect either the composite video or the S-Video cables to your TV. Do not connect both the composite and the S-Video. Some high-end DVD players use a picture reproduction system called “COLORSTREAM HD Video.” If your DVD player has COLORSTREAM HD output, use the connectors marked “COLORSTREAM HD 1/2” on the jack panel.
RGB-DTV/HDMI-DTV Input DBS Receiver Find the audio and Y, PB, PR/RGB, HDMI jacks on the back of your DBS receiver and connect them following the instructions provided with your equipment. 1 Component Out Dolby Digital Y Pb Pr Out COLORSTREAM HD INPUT 2 INPUT 1 480i/480p/ 720p/1080i 480i/480p/ 720p/1080i Audio L R Connect these cables to your TV as shown.
RGB-PC/HDMI-PC Input 1 Find the audio and RGB or DVI jacks on the back of your PC and then connect them following the instructions provided with your equipment. 2 Connect these cables to your TV as shown.
Monitor Out Setup 1 Your TV has a special signal output capability which allows you to hook up a second TV or monitor. 2 Just connect the second TV or monitor to the MONITOR OUT Audio/Video jacks located on the back of your TV. See the Operating Manual of the second TV or monitor for further details regarding that device’s input settings.
Remote Control Functions in TV Mode MODE Selects the remote operating mode: TV, VCR, Cable, DVD and Satellite. Select other operating modes, for the remote to control external devices. TV/VIDEO Selects: Analog, Video1, Video2, Front Video, Colorstream HD 1-2 and RGB and HDMI input sources . FRONT Selects the front video signal if a device, such as a camcorder or game player, is connected to the front video input jack.
Remote Control Functions in TV Mode VCR CABLE DVD SAT TV MODE LIGHT POWER POWER TV/VIDEO FRONT HDMI C/S HD1 C/S HD2 RGB C/S HD1,HD2 Selects ColorStream HD signal sources, such as DVD or HD receiver. NUMBER KEYPAD For direct channel selection and programming functions. Turns your TV or any other programmed equipment on or off, depending on mode. RGB 1 2 3 4 5 6 7 8 9 ENTER 0 CH RTN Selects: RGB-DTV and RGB-PC input sources.
On-Screen Displays This page describes your on-screen display and information banner options. Main Channel Display Displays current channel number. TV 13 CATV 16 11:17 AM Mute Mute Appears when sound is muted. PIP Display This display appears when PIP is active. 10 Volume Volume level is displayed while adjusting the sound.
Front Panel Controls 1 3 2 1 2 POWER 3 ENTER (Same as ENTER button on your remote control) 4 5 6 7 VOLUME UP / DOWN 8 Temperature indicator. (See page 7). 6 4 5 8 7 MENU CHANNEL UP / DOWN Operation indicator. (See page 7). Lamp indicator. (See page 7). W See menu pages for instructions on using the onscreen menus. W The POWER, MENU, ENTER, VOLUME, and CHANNEL buttons work just as they do on your remote control.
HDMI TM - HDMI , the HDMI logo and High-Definition Multimedia Interface are trademarks or registered trademarks of HDMI Licensing. - This set can receive the High-Definition Multimedia Interface (HDMI) or Input of Digital Visual Interface(DVI). - This set supports HDCP (High-bandwidth Digital Contents Protection) Protocol for the set (480p, 720p, 1080i) modes.
Reference Cable sample HDMI Cable (not supplied with the product) Analog Audio Cable (RCA type) (not supplied with the product) HDMI to DVI Cable (not supplied with the product) Analog Audio Cable (Stereo to RCA type) (not supplied with the product) How to use 1. Connect the HDMI Source Devices(DVD Player or Set Top Box or PC) and the set. 2. Turn on the display by pressing the POWER button on the set and HDMI Source Devices remote control. 3.
Turning the TV On 1. Refer to pages 10-16 to connect external equipment to your TV. If you have done so, plug in your TV to a standard (non-switched) 120V 60Hz power outlet. 2. If you have done so, remove the back of the remote and install in two AA batteries. Make sure batteries are properly installed (check the +/– symbols). back of remote 3. With the remote control in hand, press the POWER button to turn your TV on. Caution: Never throw batteries into a fire.
Remote control effective range 9m 30° 30° 12m VCR CABLE DVD SAT TV MODE LIGHT POWER TV/VIDEO FRONT DVI C/S HD1 C/S HD2 RGB 1 2 3 4 5 6 7 8 9 0 ENTER MUTE VOL CH RTN CH SURF VIDEO SAP PIP PIC SIZE PIPCH- PIPCH+ SWAP CC FREEZE PIP INPUT MENU EXIT PLAY PAUSE STOP REW FF REC SKIP For optimum performance, aim the remote control directly at the TV and make sure there is no obstruction between the remote control and the TV.
Manual program CHANNEL Auto program Manual program PICTURE Surf list G TV Memory Fine AUDIO 2 On 0 TIMER SPECIAL SCREEN PIP/DW LOCK Menu Prev. A d ding/Deletin g Channels ding/Deleting Channels - You can add or delete channels from the channel scan manually. 1. 2. 3. 4. 5. Press the MENU button and then use D / E button to select the CHANNEL menu. Press the G button and then use D / E button to select Manual program. Press the G button and then use D / E button to select Memory.
Surf list - Surf Channels is a convenient feature that lets you quickly scan up to 8 channels of your choice without having to wait for the TV to scan through all the in-between channels. CHANNEL Auto program Manual program PICTURE G Surf list AUDIO TIMER SPECIAL SCREEN PIP/DW LOCK Menu ----- --- ----- --- ----- --- ----- --- ----- --- ----- --- ----- --- ----- --- Prev. 1. Press the MENU button and then use D / E button to select the CHANNEL menu. 2.
Picture Mode Adjust the picture appearance to suit your preference and viewing situations. - You can manually adjust the levels for the picture quality settings, such as Contrast, Brightness, Color, etc. - You can also select a preset value from the Picture Mode menu based on the category of the program.
Color Temporature Control Auto Color Temperature Control - To initialize values (reset to default settings), select the Normal option. CHANNEL Picture Mode Color temporature PICTURE Contrast AUDIO TIMER SPECIAL G Cool Normal ACM 100 Warm Brightness 55 Off Color 55 Red 0 Sharpness 60 Green 0 Blue 0 Tint 0 SCREEN PIP/DW LOCK Menu Prev. 4 0 ENTER MUTE VOL CH RTN CH SURF VIDEO SAP PIP 1. Press the MENU button and then use D / E button to select the PICTURE menu. 2.
A CM (A ctive Color M an ag em en t) - Adjust the ACM to select the desired skin colour option. - This function works in the following mode: TV, Video 1-2, Front Video Colorstream HD 1-2, RGB-DTV, HDMI-DTV. CHANNEL Picture Mode Color temporature PICTURE AUDIO TIMER SPECIAL G ACM Contrast 100 Brightness 55 Color 55 Sharpness 60 Fleshtone 0 Greentone 0 Bluetone 0 SCREEN PIP/DW LOCK Menu Prev. 1. Press the MENU button and then use D / E button to select the menu. 2.
Sound mode - Chooes the sound options manually. CHANNEL Sound mode G Stable sound Normal Stadium PICTURE Front surround AUDIO TIMER Balance News 0 Music Treble 50 Theater Bass 50 Off SPECIAL SCREEN PIP/DW LOCK 1. 2. 3. 4. Press Press Press Press Menu Prev. the MENU button and then use D / E button to select the AUDIO menu. the G button and then use D / E button to select Sound mode. the G button and then use D / E button to select appropriate sound setup. the ENTER button to save.
Front surround - Increases the front surround sound to create more open and expanded sound. CHANNEL Sound mode Stable sound PICTURE AUDIO TIMER Front surround G SRS TSXT Balance 0 3D Echo system Treble 50 Bass 50 Off SPECIAL SCREEN PIP/DW LOCK Menu Prev. 1. Press the MENU button and then use D / E button to select the AUDIO menu. 2. Press the G button and then use D / E button to select Front surround. 3.
Stereo/SAP Broadcasts Setup - The TV can receive MTS (Multichannel Television Sound) stereo programs and any SAP (Secondary Audio Program) that accompanies the stereo program; if the broadcaster transmits one additional sound signal in addition to the original one. - Mono: The primary language is heard from left and right speakers. Signal mode is mono. - Stereo: The primary language is heard from left and right speakers. Signal mode is stereo.
Clock Setup - Setting the time can be done automatically through the PBS broadcast signal. - The PBS setup signal includes information for the current time. - Set the clock manually, if the current time is set incorrectly programed by the auto clock function. CHANNEL G Clock AUDIO Auto Off timer Manual On timer Time zone PICTURE Sleep timer Auto Auto off PBS Channel TIMER TV 2 Daylight Saving SPECIAL Auto SCREEN PIP/DW LOCK Menu Prev. 1. Press the MENU button and then use D /E 2.
On / Off Timer Setup - Time function operates only if current time has been set. - Off-Timer function overrides On-Timer function if they are set both set to the same time. - The TV must be in standby mode for the On-Timer to work. - If you do not press any button within 2 hours after the TV turns on with the On Timer function, the TV will automatically revert to standby mode. Clock CHANNEL Off timer PICTURE G On timer Sleep timer AUDIO On Off 6 Auto off TIMER : 30 AM Volume Ch.
Sleeep Timer Setup - The Sleep Timer turns the TV off at the preset time. Note that this setting is cleared when the TV is turned off. Clock CHANNEL Off timer PICTURE 10 min On timer Sleep timer AUDIO G 20 min 30 min Auto off 60 min TIMER 90 min SPECIAL 120 min 180 min SCREEN 240 min Off PIP/DW LOCK Prev. Menu 1. Press the MENU button and then use D / E button to select the TIMER menu. 2. Press the G button and then use D / E button to select Sleep timer. 3.
On-Screen Menu languages - Select your preferred language for the menus : Englisg, Spanish, or French. Language CHANNEL G English Key lock Español Captions Français PICTURE Caption / Text AUDIO TIMER SPECIAL SCREEN PIP/DW LOCK 1. Press the MENU button and then use 2. Press the G button and then use D / Menu D E E / Prev. button to select the SPECIAL menu. button to select Language. 3. Press the G button and then use D / E button to select your desired language.
Captions Setup Closed Captions Closed captioning is a process which converts the audio portion of a television program into written words which then appear as subtitles on the television screen. Closed captions allow viewers to read the dialogue and narration of television programs. Using Closed Captions Captions are the subtitles of the dialogue and narration of television programs. For prerecorded programs, program dialogue can be arranged into captions in advance.
Caption/Text Mode Selection Select a closed caption mode for displaying captioning information when provided on the program. Captions displays information at any position on the screen usually the program's dialog. Text displays information, usually at the bottom position and is used for a data service, generally not program related. CHANNEL Language Key lock PICTURE AUDIO CC1 Captions Caption / Text G CC2 CC3 TIMER CC4 Text1 SPECIAL Text2 Text3 SCREEN Text4 PIP/DW LOCK Menu Prev. 1.
Auto Adjustment - RGB (PC) mode only; This function doesn’t work for RGB-DTV mode. - Automatically adjusts picture position and minimizes image shaking. - After adjustment, if the image is still not correct, your TV is functioning properly but needs further adjustment. - The Auto config. is not active in HDMI mode. Auto config. CHANNEL G To set Manual config PICTURE Aspect ratio Cinema AUDIO NR TIMER Reset SPECIAL 0 ENTER SCREEN MUTE VOL CH RTN CH SURF PIP/DW VIDEO SAP LOCK Menu Prev.
Aspect ratio - Caution: If a 4:3 fixed image is on the screen for a long time, it may remain visible. Set every aspect ratio for TV, Video, ColorStream HD 480i sources. Use 4:3, or 16:9 for other RGB-PC and HDMI-PC sources. Horizon is not available for ColorStream HD 1-2 (480p,720p,1080i), DTV (480p,720p,1080i) sources. 1. Press the PIC SIZE button repeatedly to select the desired picture format. You can also adjust Aspect ratio in the SCREEN menu.
NR - You can select 3D NR or MPEG NR to reduce the picture noise which may appear on the screen while watching the TV. CHANNEL Auto config. Manual config PICTURE AUDIO TIMER G Aspect ratio Cinema NR 3D NR 0 Reset MPGE NR 0 5 MUTE SCREEN SAP PIP/DW LOCK PIP Menu 0 ENTER SPECIAL VOL CH RTN CH SURF VIDEO PIPCH- PIPCH+ SWAP Prev. PIC SIZE CC FREEZE PIP INPUT 1/2/3 5 1. Press the MENU button and then use D /E 2. Press the G button and then use D /E button to select NR. 3.
Parental Lock Setup Parental Control can be used to block specific channels, ratings and other viewing sources. The Parental Control Function (V-Chip) is used to block program viewing based on the ratings sent by the broadcasting station. The default setting is to allow all programs to be viewed. Viewing can be blocked by the type of program and by the categories chosen to be blocked. It is also possible to block all program viewing for a time period. To use this function, the following must be done : 1.
Parental Lock - Lets you set up blocking schemes to block specific channels, ratings, and external viewing sources. - A password is required to gain access to this menu if the Lock System is turned on CHANNEL Lock on/off G Set password On Off PICTURE MPAA AUDIO Age block Content block TIMER SPECIAL Aux. block Canadian SCREEN PIP/DW LOCK Menu Prev. 1. Press the MENU button and then use Then, press the G button D /E button to select the LOCK menu.
PIP (Picture-in-Picture) / Twin Picture Operation PIP lets you view 2 different inputs (sources) on your monitor screen at the same time. One source will be large, and the other source (PIP) will show a smaller inset image. Twin Picture splits the screen into 2, allowing 2 pictures to be shown on the TV screen at the same time. Each source is given half the screen. Watching PIP Press the PIP button to show the sub picture. Each press of PIP changes the PIP options as shown below.
PIP (Picture-in-Picture) / Twin Picture Operation Selecting PIP / Twin Picture Channels 1 Press the PIP button on the remote control to select PIP or Twin picture mode. Select the Ant/Cable source with the PIP INPUT button. 2 Use the PIPCH-/PIPCH+ button to select a channel for the sub picture. Swapping Pictures Press the SWAP button. Each time you press the SWAP button, you switch the Main and Sub pictures.
Lamp Unit Replacement • To obtain a replacement lamp unit: • In Canada, contact a Toshiba parts distributor by directing your web browser to www.toshiba.ca Click "Home Entertainment," and then click "Support." Use the replacement lamp unit model listed below only. Using any other lamp may cause damage to the TV and/or lamp. Model name is D85-LMP. CAUTION: Always replace with same type lamp unit: Model No. [D85-LMP] You must replace the lamp when: • The image gets darker or starts to deteriorate.
Lamp Unit Replacement(Contd.) 6. Pull out the handle slowly and remove the lamp case. 7. Insert the new lamp gently into the correct position. Make sure it is inserted correctly. Note: • Never subject the lamp unit to excessive shock. • Never touch the lamp unit glass or otherwise get it dirty. Doing so may affect the image quality and reduce the service life of the lamp. See “ Cleaning the lamp unit glass” at below.
Lamp Unit Replacement(Contd.) Lamp unit disposal • Place the used lamp unit in the empty box from the new lamp unit. • Keep the lamp unit out of reach of children and pets. CAUTION: Always handle the lamp unit with care. The lamp unit in this TV was designed for safe replacement by consumers; however, if the lamp unit is subjected to intentional or accidental abuse (such as excessive mechanical abuse or handling by children or pets), the unit may break, exposing sharp edges or pinch points.
Programming the Remote The remote control for your HD receiver is a multi-brand or universal remote control that can be programmed to operate most remote-controllable devices of other manufacturers. Note: The remote control may not be able to control all models of other brands. 1 2 3 4 Test your remote control.
Programming Codes: TVs TVs Brand A MARK ADMIRAL AKAI AMPRO AMSTRAD ANAM AOC BLAUPUNKT CANDLE CAPEHART CETRONIC CITIZEN CLASSIC CONCERTO CONTEC CORONADO CRAIG CROWN CURTIS MATHES CXC DAEWOO DAYTRON DYNASTY DYNATECH ELECTROHOME EMERSON FISHER FUNAI FUTURETECH GE PAGE 50 Codes 112 143 072 081 006 146 073 167 052 043 054 080 104 112 115 121 131 004 006 112 088 002 003 006 058 043 002 003 006 043 103 143 043 004 039 043 051 143 043 054 043 143 004 006 116 143 043 004 016 043 044 071 076 107 111 117 120 12
Programming Codes: VCRs VCRs Brand AIWA AKAI AMPRO ANAM AUDIO DYNAMICS BROKSONIC CANON CAPEHART CRAIG CURTIS MATHES DAEWOO DAYTRON DBX DYNATECH ELECTROHOME EMERSON FISHER FUNAI GE GO VIDEO GOLDSTAR HARMAN KARDON HITACHI INSTANTREPLAY JCL JCPENNY JENSEN JVC Codes 034 016 043 124 125 072 031 033 012 023 043 035 037 028 031 108 003 040 031 033 005 007 064 065 110 111 116 117 108 012 023 043 034 053 059 006 017 027 029 034 035 037 046 129 131 153 003 008 010 034 031 033 072 107 144 147 132 136 012 013 1
Programming Codes: SAT/DVDs SAT Brand ALPHASTAR DSR AMPLICA BIRDVIEW BSR CAPETRONICS CHANNEL MASTER CHAPARRAL CITOH CURTIS MATHES DRAKE DX ANTENNA ECHOSTAR ELECTRO HOME EUROPLUS FUJITSU Codes 123 050 051 126 053 053 013 014 018 036 008 009 077 054 050 145 005 006 010 011 112 116 024 046 076 038 040 058 093 095 096 098 099 122 089 114 017 021 Brand 129 015 055 012 007 052 141 056 057 094 097 100 022 Codes 027 133 GENERAL INSTRUMENT 003 004 029 031 101 HITACHI 139 140 HOUSTON TRACKER 033 037 051 05
Programming Codes: Cable Boxes CATV Brand ABC ANTRONIK ARCHER CABLE STAR CENTURION CENTURY CITIZEN COLOUR VOICE COMBANO COMTRONICS DIAMOND EAGLE EASTERN ELECTRICORD GE GEMINI GI GOLDEN CHANNEL HAMLIN HITACHI HOSPITALITY JERROLD Codes 003 004 042 046 053 014 005 007 024 026 092 007 007 065 090 080 081 019 030 023 020 030 057 062 032 072 008 022 054 052 074 030 049 050 052 055 070 077 002 003 Brand 039 052 014 LG M-NET MACOM MAGNAVOX MEMOREX MOVIE TIME NSC OAK 040 066 PANASONIC PARAGON PHILIPS 025
Troubleshooting Some quick and easy tips to fixing problems yourself. SYMPTOMS POSSIBLE SOLUTIONS Snowy picture and unclear sound. • Check your antenna connection or location. • Check your cable input. • Check to see if the TV/VCR button on your VCR has the TV selected. Multiple images or ‘ghost shadows.’ • Check your antenna direction and/or location. • Check your cable input. • Make sure the cable from your antenna to your TV is properly connected.
Troubleshooting (Contd.) Remote control doesn’t work. • Make sure the batteries are fresh and installed properly. Menu options can’t be changed or selected. • Try unplugging your TV for a few minutes, then plug it back in. No picture or sound when any non-cable source is selected. • Check to see if the source equipment has been turned on. • Make sure that the connections are secure on the back of your TV and on the source equipment. Weak or no Stereo Sound when using a stereo VCR.
Product Specifications • This model complies with the specifications listed below. • Designs and specifications are subject to change without notice. • This model may not be compatible with features and/or specifications that may be added in the future. Model 44HM85 Horizontal Size (Inches) Height (Inches) Depth (Inches) Weight (lbs.
562C_p.57~58(4)_en 90/6/18 1:16 PM Page 1 Limited United States Warranty for DLP Television Models TM Toshiba America Consumer Products, L.L.C. (“TACP”) makes the following limited warranties to original consumers in the United States. THESE LIMITED WARRANTIES EXTEND TO THE ORIGINAL CONSUMER PURCHASER OR ANY PERSON RECEIVING THIS DLP TELEVISION AS A GIFT FROM THE ORIGINAL CONSUMER PURCHASER AND TO NO OTHER PURCHASER OR TRANSFEREE. PRODUCTS PURCHASED IN THE U.S.A.
562C_p.57~58(4)_en 90/6/18 1:16 PM Page 2 Limited Canada Warranty for DLP Television Models your TV TM Toshiba of Canada Limited (“TCL”) makes the following limited warranties to original consumers in Canada. THESE LIMITED WARRANTIES EXTEND TO THE ORIGINAL CONSUMER PURCHASER OR ANY PERSON RECEIVING THIS DLP TELEVISION AS A GIFT FROM THE ORIGINAL CONSUMER PURCHASER AND TO NO OTHER PURCHASER OR TRANSFEREE. PRODUCTS PURCHASED IN THE U.S.A. AND USED IN CANADA ARE NOT COVERED BY THESE WARRANTIES.
Notes
HEAD OFFICE: 191 McNABB STREET, MARKHAM, ONTARIO, L3R 8H2, CANADA – TEL: (905) 470-5400 SERVICE CENTERS: TORONTO: 191 McNABB STREET, MARKHAM, ONTARIO L3R 8H2, CANADA – TEL: (905) 470-5400 MONTREAL: 18050 TRANS CANADA, KIRKLAND, QUEBEC, H9J 4A1, CANADA – TEL: (514) 390-7766 VANCOUVER: 22171 FRASERWOOD WAY, RICHMOND, B.C., V6W 1J5, CANADA – TEL: (604) 303-2500 ColorStream, StableSound, and TheaterWide are registered trademarks of Toshiba America Consumer Products, L.L.C.
Guide d’utilisation Téléprojecteur DLP mc Dossier du propriétaire Les numéros de modèle et de série sont inscrits à l’arrière du téléviseur. Veuillez inscrire ces numéros dans l’espace réservé à cette fin ci-dessous. Référez à ces numéros chaque fois que vous communiquez avec votre concessionnaire Toshiba au sujet de ce téléviseur.
562C-2~5(2)_fr 90/6/18 12:26 PM Page 2 À l’attention du client , Merci d’avoir acheté ce téléviseur Toshiba. Ce guide a pour but de vous aider à utiliser les nombreuses fonctions emballantes que vous procure ce nouveau téléviseur. Avant de le mettre sous tension, veuillez lire entièrement ce guide et le ranger à portée de la main aux fins de consultation ultérieure.
562C-2~5(2)_fr 90/6/18 12:26 PM Page 3 Consignes de sécurité importantes 1) 2) 3) 4) Veuillez lire ces consignes. Veuillez les conserver. Tenez compte de tous les avertissements. Suivez toutes les directives. 5) N’utilisez pas cet appareil près de l’eau. 6) Ne le nettoyez qu’avec un chiffon sec. 7) Ne bloquez pas les bouches d’aération. Installer cet appareil en suivant les directives du fabricant.
562C-2~5(2)_fr 90/6/18 12:26 PM Page 4 Installation (Suite de la page précédente) 27) Assurez-vous toujours que l’antenne soit correctement mise à la terre afin de protéger celle-ci adéquatement contre les surtensions et les accumulations de charges électrostatiques (voir l’article 810 du NEC).
562C-2~5(2)_fr 90/6/18 12:26 PM Page 5 MC Commentaires importants sur le téléprojecteur DLP 1) La source lumineuse de ce téléviseur est constituée d’une ampoule de projection dont la durée utile est limitée. Lorsque celle-ci s’use, l’image devient foncée ou noire, et si l'ampoule tombe en panne, il faut la remplacer. Voir « Remplacement de l'ampoule », pages 50 à 52.
Table des matières Consignes de sécurité importantes . . . . . . . . . . . . . .2-4 mc Commentaires importants sur votre téléprojecteur DLP . .5 Toshiba vous souhaite la bienvenue . . . . . . . . . . . . . . .7 Indicateurs de l’état des fonctions . . . . . . . . . . . . . . . .7 Étape 1. Raccordement du téléviseur Panneau de raccordement arrière . . . . . . . . . . . . . . . . .8 Panneau de raccordement avant . . . . . . . . . . . . . . . . .9 Branchement de l’antenne / de la télévision par câble . .
Toshiba vous souhaite la bienvenue Toshiba vous souhaite la bienvenue Félicitations! Vous venez de faire l’acquisition de l’un des meilleurs téléprojecteurs DLPMC qui soient sur le marché. Ce guide a pour mission de vous guider parmi les étapes d’installation et d’exploitation de ce téléviseur Toshiba pour que vous puissiez en jouir le plus tôt possible. Ce guide est destiné au modèle 44NHM84. Les numéros de modèle et de série sont inscrits à l'arrière du téléviseur.
Panneau de raccordement arrière Raccordement des câbles et des équipements externes sur votre téléviseur.
Panneau de raccordement avant Du côté gauche de la face avant du téléprojecteur se trouvent quatre prises servant à simplifier le raccordement d’appareils vidéo et audio tels des jeux vidéo et des caméscopes. Ces prises sont identiques à celles que l’on retrouve à l’arrière de l’unité, sur le panneau de raccordement des prises. Ainsi, la plupart des appareils raccordés à ce type de prises à cet endroit peuvent également se raccorder au panneau avant.
Branchement de l’antenne / de la télévision par Câble 1 Branchez l’antenne ou le câble dans le téléviseur tel qu’indiqué ci-contre. 2 Consultez la page 23 pour effectuer une recherche des canaux avec le balayage des canaux pour connexion d'antenne/câble.
Raccordement à un convertisseur de câble 1 Tableau de connexion murale de la télévision par câble Repérez la prise de sortie à l’arrière du convertisseur . Raccordez-la à la prise de l’antenne à l’arrière du téléviseur. Vous pouvez également repérer les prises vidéo et audio à l’arrière du convertisseur, puis raccorder celles-ci selon les directives fournies avec votre équipement. Vous pouvez jumeler ceci au branchement de tout autre équipement désiré.
Raccordement à un magnétophone Repérez la prise d’antenne à l’arrière du téléviseur. Raccordez-la à la prise de sortie RF derrière le magnétoscope. 1 Ou, repérez les prises vidéo et audio composites à l’arrière du magnétoscope, puis raccordez-les selon les directives fournies avec l’équipement. Vous pouvez raccorder les câbles vidéo composite ou S-Video au téléviseur. (Vous ne pouvez cependant pas raccorder à la fois les câbles vidéo composite et SVideo, car seul S-Video fonctionnera.
Lecteur DVD 1 Repérez les prises audio et ColorStream HD ou S-Vidéo à l’arrière du lecteur DVD, puis raccordez-les en suivant les directives fournies avec l’équipement. Vous pouvez raccorder les câbles vidéo à composante ou S-Vidéo à votre téléviseur. Ne raccordez pas à la fois le câble pour vidéo à composante et S-Vidéo. Certains lecteurs DVD de haut de gamme font appel à un système de reproduction de l’image nommé « COLORSTREAM HD Video.
Entrée RBV-DTV/HDMI-DTV Récepteur DBS Repérez les prises audio et Y, PB, PR/RVB/HDMI (Y, PB, PR/RVB/DVI) à l’arrière du récepteur DBS (de radiodiffusion par satellite), puis raccordez-les selon les directives fournies avec votre équipement. 1 INPUT 2 INPUT 1 480i/480p/ 720p/1080i 480i/480p/ 720p/1080i Audio L R Y Raccordez ces câbles au téléviseur de la manière indiquée ci-contre.
Entrée RVB-PC/HDMI-PC 1 Repérez les prises audio et RVB ou DVI à l’arrière de votre PC puis raccordez-les en suivant les directives fournies avec votre équipement. 2 Raccordez ces câbles au téléviseur, tel qu’indiqué.
Installation de la sortie Écran 1 Votre téléviseur est doté d’une fonction particulière de sortie audio vous permettant d’y raccorder un deuxième téléviseur ou un deuxième écran. 2 Il suffit de raccorder le deuxième téléviseur ou écran aux prises Audio/Video MONITOR OUT situées à l’arrière du téléviseur. Consultez le guide d’utilisation fourni avec le deuxième téléviseur ou écran pour obtenir de plus amples détails sur les réglages d’entrée de ces appareils.
Fonctions de la télécommande en mode TV MODE Sert à choisir le mode d’exploitation à distance : TV, VCR, Cable, DVD et Satellite. Sélectionnez d’autres modes d’exploitation pour contrôler d’autres appareils au moyen de la télécommande. TV/VIDEO (TÉLÉ / VIDÉO) Choix de sources d’entrées dont : Analog, Video 1, Video 2, Front video, ColorStream HD1-2, RVB et HDMI (RVB et HDMI). TÉMOINS VCR CABLE DVD SAT TV MODE LIGHT POWER MUTE (ASSOURDIR) Permet d’activer et de désactiver le son.
Fonctions de la télécommande en mode TV VCR CABLE DVD SAT TV MODE LIGHT POWER POWER (MARCHE/ARRÊT) TV/VIDEO FRONT HDMI C/S HD1 C/S HD2 RGB C/S HD1,HD2 Sert à sélectionner des signaux ColorStream HD provenant de sources telles qu’un lecteur DVD ou un écran HD. CLAVIER NUMÉRIQUE Sert à la sélection directe de canaux et de fonctions de programmation.
Affichages à l’écran Cette page décrit les options d’affichages et de bannières d’informations à l’écran. Affichage du canal principal Affiche le numéro de la chaîne présentement écoutée. TV 13 CATV 16 11:17 AM Mute Assourdir S’affiche lorsque le son est assourdi. Affichage I.D.I. Données affichées lorsque la fonction I.D.I. est activée. 10 Volume Affichage du niveau de l’audio pendant le réglage du son.
Commandes du panneau avant 1 3 2 6 4 1 2 POWER 3 ENTER (ENTRÉE – identique à la touche ENTER de la télécommande) 4 5 6 7 VOLUME FORT / FAIBLE 8 Témoin de température (Voir la page 7). 5 8 7 MENU CHAÎNE PRÉCÉDENTE / SUIVANTE Témoin d’exploitation (Voir la page 7). Témoin de l'ampoule (Voir la page 7). W Consulter les pages du menu pour des directives sur la manière d’utiliser les menus à l’écran.
HDMI - HDMITM, the HDMI logo and High-Definition Multimedia Interface are trademarks or registered trademarks of HDMI Licensing. - This set can receive the High-Definition Multimedia Interface (HDMI) or Input of Digital Visual Interface(DVI). - This set supports HDCP (High-bandwidth Digital Contents Protection) Protocol for the set (480p, 720p, 1080i) modes.
Référence Échantillon de câble Câble HDMI (non fourni) Câble audio analogique (type RCA) (non fourni) Câble HDMI à DVI (non fourni) Câble audio analogique (stéréo à type RCA) (non fourni) How to use 1. Connect the HDMI Source Devices(DVD Player or Set Top Box or PC) and the set. 2. Turn on the display by pressing the POWER button on the set and HDMI Source Devices remote control. 3. Select HDMI Input source in Main Input option of PIP/DW menu. 4. Check the image on your set.
Mise en circuit du téléviseur 1.Consultez les pages 10 à 16 pour raccorder des équipements externes au téléviseur. Si c’est déjà fait, branchez le téléviseur à une prise de courant standard de 120V, 60 Hz, non commutée 2. Si c’est déjà fait, enlevez la partie arrière de la télécommande pour y installer des piles AA. Faites en sorte d’installer les piles correctement (vérifiez les symboles +/-). back of remote 3.
Portée utile de la télécommande 9m 30° 30° 12m VCR CABLE DVD SAT TV MODE LIGHT POWER TV/VIDEO FRONT DVI C/S HD1 C/S HD2 RGB 1 2 3 4 5 6 7 8 9 0 ENTER MUTE VOL CH RTN CH SURF VIDEO SAP PIP PIC SIZE PIPCH- PIPCH+ SWAP CC FREEZE PIP INPUT MENU EXIT PLAY PAUSE STOP REW FF REC SKIP Pour un rendement optimal, pointez la télécommande en ligne droite sur le téléviseur et assurez-vous qu’il n’y ait aucun objet entre la télécommande et le téléviseur.
Mise en Mise en mémoire CHANNEL Déchiffrage Manuelle PICTURE Surf list G TV Mémoire 2 Marche Synto AUDIO 0 TIMER SPECIAL SCREEN PIP/DW LOCK Menu Préc. suppressi on du suppression du canal canal en cours -L’on peut ajouter ou effacer des canaux de la mémoire. 1. Presser la touche MENU puis la touche D / E pour sélectionner menu CANAL. 2. Presser la touche G , puis la touche D / E pour sélectionner Manuelle. 3. Presser la touche G , puis la touche D / E pour sélectionner Mémoire. 4.
Surf list - Les Surf Channels une fonction pratique permettant de balayer jusqu’à 8 canaux sans avoir à passer par tous les canaux entre les canaux. CHANNEL Déchiffrage Manuelle PICTURE G Surf list AUDIO TIMER SPECIAL SCREEN PIP/DW LOCK Menu ----- --- ----- --- ----- --- ----- --- ----- --- ----- --- ----- --- ----- --- Préc. 1. Presser la touche MENU puis la touche D / E pour sélectionner menu CHANNEL. 2. Presser la touche G , puis la touche D / E pour sélectionner Surf list.
Mode image Réglez l’image en fonction de vos préférences et de votre manière de visionner. - Vous pouvez régler l’image manuellement (contraste, Brillance, couleur, etc.). - Vous pouvez également prédéterminer une valeur à partir du menu Mode Image en fonction de la catégorie de programme.
Contrôle de température de couleur Réglage de contrôle automatique de couleur -Pour initialiser la valeur réglée, sélectionner Normal. CHANNEL PICTURE AUDIO TIMER SPECIAL Mode image Température couleur G Froide ACM Normal Chaude Contraste 100 Brillance 55 Personnel Couleur 55 Rouge Netteté 60 Vert 0 Teinte 0 Bleu 0 0 SCREEN PIP/DW LOCK Préc. Menu 4 0 ENTER MUTE VOL CH RTN CH SURF VIDEO SAP PIP 1. Presser la touche MENU puis la touche D /E 2.
A CM (A ctive Color M an ag em en t) - Adjust the ACM to select the desired skin colour option. - This function works in the following mode: TV, Video 1-2, Front Video Colorstream HD 1-2, RVB-DTV, HDMI-DTV. Mode image CHANNEL Température couleur PICTURE G ACM AUDIO TIMER SPECIAL Ton de chair 0 Contraste 100 Tons verts 0 Brillance 55 Tons bleus 0 Couleur 55 Netteté 60 SCREEN PIP/DW LOCK 1. Presser la touche MENU puis la touche 2. Presser la touche Préc.
Mode Sonore - Sert à choisir les options manuellement. CHANNEL Mode sonore G Son stable Normal Stade PICTURE Ambiophonie AUDIO TIMER Nouvelles Équilibre 0 Musique Aiguës 50 Théâtre Graves 50 Arrêt SPECIAL SCREEN PIP/DW LOCK Menu Préc. 1. Presser la touche MENU puis la touche pour sélectionner menu AUDIO. 2. Presser la touche G , puis la touche D / E pour sélectionner Mode sonore. 3.
Ambiophonie (Tonalité ambiophonique avant) - Sert à augmenter les sons ambiophoniques avant afin de créer des sons plus ouverts et étendus. CHANNEL Mode sonore Son stable PICTURE AUDIO TIMER Ambiophonie G SRS TSXT Équilibre 0 3D Echo system Aiguës 50 Graves 50 Arrêt SPECIAL SCREEN PIP/DW LOCK Préc. Menu 1. Presser la touche MENU puis la touche D / E pour sélectionner menu AUDIO. , puis la touche D / E pour sélectionner Ambiophonie. 3.
Sélection des signaux - Le téléviseur peut recevoir les programmes stéréo multi-audio et SAP (2 versions) accompagnant le programme stéréo, si le diffuseur transmet un signal sonore additionnel en plus du signal d’origine. - Mono: la langue primaire sort des haut-parleurs gauche et droit. Le mode est monophonique. - Stéréo: la langue primaire sort des haut-parleurs gauche et droit. Le mode est stéréophonique. - SAP: la langue seconde sort des haut-parleurs gauche et droit. 1.
Réglage de la pendule - Pour régler automatiquement l’heure par l’entremise du signal de diffusion PBS. - Le signal de canal PBS comprend des informations sur l’heure appropriée. - Régler la pendule manuellement, si l’heure en cours est incorrecte par la fonction automatique. CHANNEL Pendule Heure arrêt PICTURE Heure marche AUDIO G Auto Manuelle Fuseau Minuterie Arrêt auto Auto Chaîne PBS TIMER TV 2 Heure avancée SPECIAL Auto SCREEN PIP/DW LOCK Menu Préc. 1.
Réglage de la minuterie marche-arrêt - La fonction minuterie ne peut être actionnée que si l’heure a été réglée. - La fonction minuterie arrêt est avant la fonction minuterie marche si elles sont réglées ensemble. - Le téléviseur doit être en mode attente pour que la heure marche fonctionne. - À moins qu’une touche ne soit pressée dans un délai de 2 heures après avoir actionné la fonction heure marche, l’appareil se met automatiquement hors circuit.
Réglage de la minuterie de mise en veille - Cette fonction met automatiquement l’appareil hors circuit après une durée réglée. CHANNEL Pendule Heure arrêt PICTURE AUDIO 10 min Heure marche G Minuterie 20 min 30 min Arrêt auto 60 min TIMER 90 min SPECIAL 120 min 180 min SCREEN 240 min Arrêt PIP/DW LOCK Menu Préc. 1. Presser la touche MENU puis la touche D / E pour sélectionner menu TIMER. 2. Presser la touche G , puis la touche D / E pour sélectionner Minuterie. 3.
Langue des menus à l’écran Sélectionnez la langue des menus à l’écran : English, Español et Français. CHANNEL Langage(Language) G English Verrouillage Español Sous-Titres Français PICTURE AUDIO Sous-Titr/TX TIMER SPECIAL SCREEN PIP/DW LOCK 1. Presser la touche MENU puis la touche G 2. Presser la touche puis la touche Menu D /E D /E Préc. pour sélectionner menu SPECIAL. pour sélectionner Langage. 3. Presser la touche G button and then use D / E pour sélectionner la langue désirée.
Réglage des sous-titres Utilisation des sous-titr es La fonction de sous-titres est un procédé qui convertit la portion audio d’un programme télé en mots écrits qui figurent à l’écran. Ils permettent au spectateur de lire les dialogues à l’écran. Utilisation des sous-titres Les sous-titres donnent les dialogues et les narrations des pro-grammes télé. Pour les programmes préenregistrés, le dialogue peut être arrangé à l’avance en sous-titres.
Sélection du mode Sous-titre / Texte Sélectionnez le mode d’affichage des sous-titres lorsque la programmation le prend en charge. Le mode Sous-titre affiche l’information à peu près n’importe où à l’écran. Il sert généralement à afficher les dialogues correspondant à la programmation. Le mode Texte affiche généralement l’information au bas de l’écran. Il sert à des services de données, non reliés à la programmation.
Réglage automatique - Mode RVB (PC) seulenent. - Pour régler automatiquement la position de l’image et élimine toute vibration de l’image. - Si l’image n’est pas encore correcte, le téléviseur fonctionne correctement, mais doit être encore réglé. - Config.auto ne sont pas actives en mode HDMI. Config. auto CHANNEL G Régler Config. manuelle PICTURE Allongement Cinema AUDIO NR TIMER Réajuste SPECIAL 0 ENTER SCREEN MUTE VOL CH RTN CH SURF PIP/DW VIDEO SAP LOCK Préc. Menu PIP 1.
Allongement - Si 4 :3 demeure à l’écran pendant une longue période, une image fixe peut demeurer. Régler chaque ratio aspect pour les sources TV, Video, ColorStream HD 480i. Utiliser 4:3 ou 16:9 pour d’autres sources RVB-PC et HDMI-PC. Horizon n’est pas disponible pour ColorStream HD 1-2 (480p,720p,1080i), DTV (480p,720p,1080i). 1. Presser la touche PIC SIZE de façon répétitive pour sélectionner le format d’image désiré. L’on peut aussi régle PIC SIZE au menu ECRAN.
NR - You can select 3D NR or MPEG NR to reduce the picture noise which may appear on the screen while watching the TV. Config. auto CHANNEL Config. manuelle PICTURE G Allongement Cinema AUDIO TIMER NR 3D NR 0 Réajuste MPGE NR 0 5 MUTE SCREEN SAP PIP/DW PIP LOCK Menu 0 ENTER SPECIAL VOL CH RTN CH SURF VIDEO PIPCH- PIPCH+ SWAP Préc. PIC SIZE CC FREEZE PIP INPUT 1/2/3 5 1. Presser la touche MENU puis la touche 2. Presser la touche 3.
Réglage du verrouillage parental La sélection-parent peut être utilisée pour verrouiller des canaux spécifiques, des cotes et autres sources de visionnement. The Parental Control Function (V-Chip) is used to block program viewing based on the ratings sent by the broadcasting station. The default setting is to allow all programs to be viewed. Viewing can be blocked by the type of program and by the categories chosen to be blocked. It is also possible to block all program viewing for a time period.
Verrouillage parental - Permet de régler les paramètres pour verrouiller des canaux spécifiques, des cotes ou autres sources. - Un mot de passe est requis pour accéder à ce menu si le système de verrouillage est activé. CHANNEL Blocage M/A G Mot de Passe marche Arrêt PICTURE MPAA AUDIO Âge bloc Cont. bloc TIMER SPECIAL Aux. bloc Canadian SCREEN PIP/DW LOCK Menu Préc. 1. Press the MENU button and then use Then, press the G button D /E button to select the LOCK menu.
Exploitation en mode image dans l’image (I.D.I.) et Images doubles Le mode I.D.I. (aussi nommée PIP) permet de visionner en même temps deux sources d’images distinctes à l’écran, dont l’une plus grande que l’autre. L’image le plus petite est insérée en cartouche en mode I.D.I. Le mode Images doubles (aussi nommé Twin) divise l’écran en deux de manière à ce que vous puissiez visionner deus images à la fois. Chacune des deux sources se partage l’écran. Watching PIP Pour afficher l’image en mode I.D.I.
Exploitation en mode image dans l'image (I.D.I.) et Images doubles Sélection de canaux en mode I.D.I. et Images doubles 1 Appuyez sur la touche PIP de la télécommande pour sélectionner le mode Incrustation d’image ou Images doubles. Sélectionnez la source Ant/Cable à l’aide de la touche PIP INPUT (Entrée I.D.I.). 2 Pour sélectionner le canal correspondant à l'I.D.I., utilisez la touche PIPCH-/PIPCH+. Swapping Pictures Appuyez sur la touche SWAP.
Remplacement de l'ampoule • Pour obtenir une ampoule de rechange : • Au Canada, communiquez avec un distributeur de pièces Toshiba en consultant le www.toshiba.ca. Cliquez sur « Produits grand public ». Dans la fenêtre contextuelle de droite, intitulée « Recherche concessionnaire/Soutien et produits », sélectionnez « Recherche de concessionnaire et soutien ».
Remplacement de l'ampoule (suite) 6. Tirez lentement sur la poignée, puis enlevez le module de l'ampoule. 7. Introduire lentement la nouvelle ampoule au bon endroit. Assurez-vous de bien l’y insérer. Remarque: • Ne jamais soumettre l'ampoule à des chocs excessifs • Ne jamais toucher le verre de l'ampoule ni le salir. Le cas échéant, la qualité de l’image et la durée utile de l'ampoule pourraient en être affectées. Voir « Nettoyage du verre de l'ampoule » ci-après.
Remplacement de l'ampoule (suite) Pour disposer de l'ampoule • Posez l'ampoule usée dans l’emballage de l'ampoule neuve. • Tenez l'ampoule usée loin de la portée des enfants et des animaux. ATTENTION: Manipulez toujours l'ampoule avec soin.
Programmation de la télécommande La télécommande du téléviseur est une télécommande multimarque ou universelle pouvant être programmée de manière à opérer la plupart des appareils télécommandables d’autres fabricants. Remarque : Même si cette télécommande prend en charge la plupart des marques de magnétoscopes, de lecteurs DVD et module de raccordement par satellite, certains équipements peuvent ne pas être compatibles avec elle. 1 Faites l’essai de la télécommande.
Codes de programmation (TV) TV Marque A MARK ADMIRAL AKAI AMPRO AMSTRAD ANAM AOC BLAUPUNKT CANDLE CAPEHART CETRONIC CITIZEN CLASSIC CONCERTO CONTEC CORONADO CRAIG CROWN CURTIS MATHES CXC DAEWOO DAYTRON DYNASTY DYNATECH ELECTROHOME EMERSON FISHER FUNAI FUTURETECH GE PAGE 50 Codes 112 143 072 081 006 146 073 167 052 043 054 080 104 112 115 121 131 004 006 112 088 002 003 006 058 043 002 003 006 043 103 143 043 004 039 043 051 143 043 054 043 143 004 006 116 143 043 004 016 043 044 071 076 107 111 117 1
Codes de programmation (Magnétoscopes) Magnétoscopes Marque AIWA AKAI AMPRO ANAM AUDIO DYNAMICS BROKSONIC CANON CAPEHART CRAIG CURTIS MATHES DAEWOO DAYTRON DBX DYNATECH ELECTROHOME EMERSON FISHER FUNAI GE GO VIDEO GOLDSTAR HARMAN KARDON HITACHI INSTANTREPLAY JCL JCPENNY JENSEN JVC Codes 034 016 043 124 125 072 031 033 012 023 043 035 037 028 031 108 003 040 031 033 005 007 064 065 110 111 116 117 108 012 023 043 034 053 059 006 017 027 029 034 035 037 046 129 131 153 003 008 010 034 031 033 072 107
Codes de programmation (Télévision par satellite / lecteurs DVD) Télévision par satellite Marque ALPHASTAR DSR AMPLICA BIRDVIEW BSR CAPETRONICS CHANNEL MASTER CHAPARRAL CITOH CURTIS MATHES DRAKE DX ANTENNA ECHOSTAR ELECTRO HOME EUROPLUS FUJITSU Codes 123 050 051 126 053 053 013 014 018 036 008 009 077 054 050 145 005 006 010 011 112 116 024 046 076 038 040 058 093 095 096 098 099 122 089 114 017 021 Marque 129 015 055 012 007 052 141 056 057 094 097 100 022 Codes 027 133 GENERAL INSTRUMENT 003 00
Codes de programmation (Boîtes à câbles) Télévision par câble Marque ABC ANTRONIK ARCHER CABLE STAR CENTURION CENTURY CITIZEN COLOUR VOICE COMBANO COMTRONICS DIAMOND EAGLE EASTERN ELECTRICORD GE GEMINI GI GOLDEN CHANNEL HAMLIN HITACHI HOSPITALITY JERROLD Codes 003 004 042 046 053 014 005 007 024 026 092 007 007 065 090 080 081 019 030 023 020 030 057 062 032 072 008 022 054 052 074 030 049 050 052 055 070 077 002 003 Marque 039 052 014 LG M-NET MACOM MAGNAVOX MEMOREX MOVIE TIME NSC OAK 040 066 PANA
Dépannage Voici quelques conseils pratiques et faciles de dépannage. SYMPTOMES SOLUTIONS POSSIBLES Image neigeuse / son indistinct • Vérifier le raccordement ou l’emplacement de l’antenne. • Vérifier l’entrée du câble. • Voir si la touche TV/VCR du magnétoscope est réglée à TV. Images multiples ou « image fantôme » • Vérifier l’orientation et / ou l’emplacement de l’antenne. • Vérifiez l’entrée du câble. • Assurez-vous que le câble raccordant l’antenne au téléviseur est bien connecté.
Dépannage (suite) La télécommande ne fonctionne pas • Assurez-vous que les piles sont neuves et qu’elles sont bien installées. Impossible de modifier les options sélectionnées ou de les sélectionner • Essayez de débrancher le téléviseur pendant quelques minutes, puis de le brancher de nouveau. Absence d’image et de son en sélectionnant une source non câblée • Vérifiez si l’appareil source est sous tension.
Fiche technique du produit • Ce modèle est conforme aux spécifications décrites ci-après. • La conception et les spécifications peuvent être modifiées sans préavis. • Ce modèles peut être incompatible avec toutes fonctions et / ou spécifications ajoutées à une date ultérieure. Modèle 44HM85 Taille horizontale Hauteur Profondeur Poids Alimentation AC 120V, 60Hz Système de télévision NTSC. Exige un boîtier numérique supplémentaire pour la réception par satellite ou numérique par le câble.
562C-57~58(4)_Fr 90/6/18 12:29 PM Page 1 Garantie limitée aux États-Unis Téléviseurs de modèle DLPMC Toshiba America Consumer Products, L.L.C. (« TACP ») accorde les garanties limitées suivantes aux consommateurs d’origine aux États-Unis. CES GARANTIES LIMITÉES SONT ACCORDÉES STRICTEMENT ÀU PREMIER ACHETEUR OU À TOUTE PERSONNE RECEVANT EN CADEAU CE TÉLÉVISEUR DLP DU PREMIER ACHETEUR, ET À AUCUN AUTRE ACHETEUR OU CESSIONNAIRE.
562C-57~58(4)_Fr 90/6/18 12:29 PM Page 2 Garantie limitée au Canada Téléviseurs de modèle DLPMC Toshiba du Canada Limitée (TCL) accorde les garanties limitées suivantes aux consommateurs d’origine au Canada. CES GARANTIES LIMITÉES SONT ACCORDÉES STRICTEMENT ÀU PREMIER ACHETEUR OU À TOUTE PERSONNE RECEVANT EN CADEAU CE TÉLÉVISEUR DLP DU PREMIER ACHETEUR, ET À AUCUN AUTRE ACHETEUR OU CESSIONNAIRE. CES GARANTIES NE COUVRENT PAS LES PRODUITS ACHETÉS AUX ÉTATS-UNIS AUX FINS D’UTILISATION AU CANADA.
Notes
SIÈGE SOCIAL : 191 McNABB STREET, MARKHAM, ONTARIO, L3R 8H2, CANADA – TÉL. : 905 470-5400 CENTRES DE SERVICE : TORONTO : 191 McNABB STREET, MARKHAM, ONTARIO L3R 8H2, CANADA – TÉL. : 905 470-5400 MONTRÉAL : 18050, RTE TRANSCANADIENNE, KIRKLAND (QUÉBEC) H9J 4A1, CANADA – TÉL. : 514 390-7766 VANCOUVER : 22171 FRASERWOOD WAY, RICHMOND, B.C., V6W 1J5, CANADA – TÉL.: 604 303-2500 ColorStream, StableSound et TheaterWide sont des marques déposées de la Toshiba America Consumer Products, L.L.C.