Qosmio G20 TOSHIBA Qosmio G20 Portable Personal Computer User’s Manual
User’s Manual Copyright © 2005 by TOSHIBA Corporation. All rights reserved. Under the copyright laws, this manual cannot be reproduced in any form without the prior written permission of TOSHIBA. No patent liability is assumed, with respect to the use of the information contained herein.
User’s Manual Trademarks IBM is a registered trademark and IBM PC is a trademark of International Business Machines Corporation. Intel, Intel SpeedStep, Centrino and Pentium are trademarks or registered trademarks of Intel Corporation. Windows and Microsoft are registered trademarks of Microsoft Corporation. Photo CD is a trademark of Eastman Kodak. Bluetooth is a trademark owned by its proprietor and used by TOSHIBA under license. Memory Stick is a registered trademark and i.
User’s Manual Modem warning notice Conformity Statement The equipment has been approved to [Commission Decision “CTR21”] for pan-European single terminal connection to the Public Switched Telephone Network (PSTN). However, due to differences between the individual PSTNs provided in different countries/regions the approval does not, of itself, give an unconditional assurance of successful operation on every PSTN network termination point.
User’s Manual Optical disc drive safety instructions Be sure to check the international precautions at the end of this section. Panasonic DVD Super Multi with Double Layer Recording UJ-845 ■ The DVD Super Multi drive with Double Layer Recording model employs a laser system. To ensure proper use of this product, please read this instruction manual carefully and retain for future reference. Should the unit ever require maintenance, contact an authorized service location.
User’s Manual International precautions CAUTION: This appliance contains a laser system and is classified as a “CLASS 1 LASER PRODUCT.” To use this model properly, read the instruction manual carefully and keep this manual for your future reference. In case of any trouble with this model, please contact your nearest “AUTHORIZED service station.” To prevent direct exposure to the laser beam, do not try to open the enclosure.
User’s Manual OBS! Apparaten innehåller laserkomponent som avger laserstråining överstigande gränsen för laserklass 1. VAROITUS. Suojakoteloa si saa avata. Laite sisältää laserdiodin, joka lähetää näkymätöntä silmilie vaarallista lasersäteilyä. CAUTION: USE OF CONTROLS OR ADJUSTMENTS OR PERFORMANCE OF PROCEDURES OTHER THAN THOSE SPECIFIED IN THE OWNER’S MANUAL MAY RESULT IN HAZARDOUS RADIATION EXPOSURE.
User’s Manual viii User’s Manual
Qosmio G20 Table of Contents Preface Manual contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . xvii Conventions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . xviii Abbreviations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . xviii Icons . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Table of Contents Front with the display open . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2-8 Indicators. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2-11 System indicators . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-11 Keyboard indicators. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Table of Contents Sound System . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-6 Using the microphone . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-6 SoundMAX control panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-7 Virtual Sound . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Table of Contents Chapter 5 : The Keyboard Typewriter keys . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5-1 Function keys: F1 … F12 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5-2 Soft keys: Fn key combinations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5-2 Emulating keys on enhanced keyboard . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Table of Contents Chapter 7 : HW Setup Accessing HW Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . HW Setup window . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Configuring the Execute-Disable Bit Capability and Front Operation Panel. . . . . Starting and Ending the BIOS Setup Program . . . . . . . . . . . . . . . . . . . . . . . . . . . . Execute-Disable Bit Capability . . . . . . . . . . .
Table of Contents Memory expansion . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .9-12 Installing memory module . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .9-13 Removing memory module . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .9-14 Battery packs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .9-15 AC adaptor.
Table of Contents PC card . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10-9 ExpressCard . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10-10 SD card . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10-10 Memory Stick/Memory Stick Pro . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Table of Contents Appendix D : Bluetooth wireless technology Interoperability Bluetooth wireless technology and your Health . . . . . . . . . . . . . . . . . . . . . . . . . . . Regulatory statements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . General . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . European Union (EU) and EFTA . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Qosmio G20 Preface Congratulations on your purchase of the Qosmio G20 computer. This powerful notebook computer provides excellent expansion capability, including multimedia devices, and it is designed to provide years of reliable, high-performance computing. This manual tells how to set up and begin using your Qosmio G20 computer. It also provides detailed information on configuring your computer, basic operations and care, using optional devices and troubleshooting.
Preface Chapter 4, Operating Basics, includes instructions on using the following devices: Touch Pad, USB floppy disk drive (optional), TV Tuner (optional), Sound System, Modem, Wireless communication features, LAN. It also provides tips on care of the computer, floppy disks and CD/DVDs. Chapter 5, The Keyboard, describes special keyboard functions including the keypad overlay and hot keys. Chapter 6, Power, gives details on the computer’s power resources and battery save modes.
Preface Key operation Some operations require you to simultaneously use two or more keys. We identify such operations by the key top symbols separated by a plus sign (+). For example, Ctrl + C means you must hold down Ctrl and at the same time press C. If three keys are used, hold down the first two and at the same time press the third.
Preface xx User’s Manual
Qosmio G20 General Precautions TOSHIBA computers are designed to optimize safety, minimize strain and withstand the rigors of portability. However, certain precautions should be observed to further reduce the risk of personal injury or damage to the computer. Be certain to read the general precautions below and to note the cautions included in the text of the manual. Stress injury Carefully read the Safety Instruction Manual.
General Precautions Mobile phone Use of mobile phones can interfere with the audio system. Computer operation is not impaired but is recommended that a distance of 30 cm be maintained between the computer and a mobile phone in use. Disclaimers LCD Over a period of time, and depending on the usage of the computer, the brightness of the LCD screen will deteriorate. This is an intrinsic characteristic of LCD technology. Maximum brightness is only available when operating in AC power mode.
General Precautions Copy Protection Copy protection technology included in certain media may prevent or limit recording or viewing of the media. HDD Drive Capacity 1 Gigabyte (GB) means 1000 × 1000 × 1000 = 1,000,000,000 bytes using powers of 10. The computer operating system, however, reports storage capacity using powers of 2 for the definition of 1 GB = 1024 × 1024 × 1024 = 1,073,741,824 bytes, and therefore may show less storage capacity.
General Precautions QosmioTM Player The QosmioTM Player is not a Windows based application. Battery life will be less than when using similar applications in a Windows operating system. LCD Brightness and Eye Stain Your LCD display has a brightness approaching that of a TV device. We recommend that you adjust the brightness of your LCD to a comfortable level to prevent possible strain on your eyes.
General Precautions The cautions on use of a Qosmio G20 series computer 1. Cleaning of dust accumulated on the cooling vent of the computer. When you use your computer in a dusty area, dirt and debris may accumulate on the cooling vents at the under side of your unit. If this occurs, the accumulated dust can cause insufficient heat dissipation which may result in the computer shutting down during use. Carefully clean the dust from the vents using a vacuum cleaner. 2.
General Precautions xxvi User’s Manual
Qosmio G20 Chapter 1 Introduction This chapter provides an equipment checklist, and it identifies the computer’s features, options and accessories. Some of the features described in this manual may not function properly if you use an operating system that was not preinstalled by TOSHIBA. Equipment checklist Carefully unpack your computer. Save the box and packing materials for future use.
Introduction Software Microsoft®Windows XP Home Edition ■ The following software is preinstalled: ■ Microsoft® Windows XP Home Edition ■ TOSHIBA Utilities ■ DVD Video Player ■ TOSHIBA Power Saver ■ TOSHIBA ConfigFree ■ TOSHIBA Assist ■ TOSHIBA Controls ■ TOSHIBA PC Diagnostic Tool ■ TOSHIBA Touch and Launch ■ TOSHIBA TouchPad On/Off Utility ■ TOSHIBA Zooming Utility ■ TOSHIBA Picture Enhancement Utility ■ InterVideo WinDVR (TV Tuner models only) ■ TOSHIBA SD Memory Card Format ■ TOSHIBA Acoustic Silencer ■
Introduction Microsoft®Windows XP Media Center Edition ■ The following software is preinstalled: ■ Microsoft® Windows XP Media Center Edition ■ TOSHIBA Utilities ■ DVD Video Player ■ TOSHIBA Power Saver ■ TOSHIBA Assist ■ TOSHIBA Controls ■ TOSHIBA PC Diagnostic Tool ■ TOSHIBA Touch and Launch ■ TOSHIBA TouchPad On/Off Utility ■ TOSHIBA Zooming Utility ■ TOSHIBA Picture Enhancement Utility ■ TOSHIBA ConfigFree ■ TOSHIBA SD Memory Card Format ■ TOSHIBA Acoustic Silencer ■ TOSHIBA Virtual Sound ■ TOSHIBA Hot
Introduction Features The computer uses TOSHIBA’s advanced Large Scale Integration (LSI), Complementary Metal-Oxide Semiconductor (CMOS) technology extensively to provide compact size, minimum weight, low power usage, and high reliability. This computer incorporates the following features and benefits: Processor Built-in The computer is equipped with an Intel® Pentium® M processor, which incorporates a 2MB level 2 cache memory. It also supports Enhanced Intel® SpeedStepTM technology.
Introduction Disks Hard disk drive Available in three sizes. ■ 60.0 billion bytes (55.88 GB) ■ 80.0 billion bytes (74.52 GB) ■ 100.0 billion bytes (93.16GB) Depending on your configuration, your computer is equipped with either one or two hard disk drives. Other hard disk drives may be introduced. DVD Super Multi drive Double Layer (UJ-845) Your computer is equipped with a full-size DVD Super Multi drive module that lets you record data to rewritable CD/DVDs as well as run 12cm (4.72") CD/DVDs.
Introduction Ports External monitor Analog VGA port supports VESA DDC2B compatible functions. Universal Serial Bus (USB 2.0) The computer has Universal Serial Bus ports that comply with the USB 2.0 standard, which enables data transfer speeds 40 times faster than the USB 1.1 standard (The ports also support USB 1.1). i.LINK™ (IEEE1394) This port enables high-speed data transfer directly from external devices such as digital video cameras.
Introduction User’s Manual S-Video in Port A camcorder or other recording device can be connected to your computer via an S-Video in cable (optional) for importing video data. Connect the cable to this port. Refer to the S-Video-in section in Chapter 9, Optional Devices. S-Video out port The S-Video out port lets you transfer NTSC or PAL data to external devices. Refer to the TV section in Chapter 9, Optional Devices.
Introduction Communications 1-8 Modem An internal modem provides capability for data and fax communication. It supports V.90 (V.92). The speed of data transfer and fax depends on analog telephone line conditions. It has a modem jack for connecting to a telephone line. Both of V.90 and V.92 are supported only in USA, Canada, UK, France, Germany and Australia. Only V.90 is available in other regions.
Introduction ■ The numerical values shown above are the theoretical maximums for Wireless LAN standards. The actual values may differ. ■ The transmission speed over the wireless LAN and the distance over which wireless LAN can reach may vary depending on surrounding electromagnetic environment, obstacles, access point design and configuration, and client design and software/hardware configurations. The Transmit Rate (at X Mbit/s) is the theoretical maximum speed under the IEEE802.11 (a/b/g) standard.
Introduction 1-10 HDD automatic power off This feature automatically cuts off power to the hard disk drive when it is not accessed for a time specified. Power is restored when the hard disk is accessed. You can specify the time in the HDD power off item of the Basic Setup tab in TOSHIBA Power Saver. System automatic Standby/Hibernation This feature automatically shuts down the system into Standby Mode or Hibernation Mode when there is no input or hardware access for a time specified.
Introduction User’s Manual System automatic Standby/Hibernation This feature automatically shuts down the system into Standby Mode or Hibernation Mode when there is no input or hardware access for a time specified. You can specify the time and select either System Standby or System Hibernation in the System standby and System item of the Basic Setup tab in TOSHIBA Power Saver Keypad overlay A ten-key pad is integrated into the keyboard.
Introduction Heat dispersal 1-12 To protect from overheating, the CPU has an internal temperature sensor. If the computer’s internal temperature rises to a certain level, the cooling fan is turned on or the processing speed is lowered. Use the Cooling Method item of the Basic Setup tab in TOSHIBA Power Saver. ■ Maximum Performance Turns on fan first, then if necessary lowers CPU processing speed. ■ Performance Uses a combination of fan and lowering the CPU processing speed.
Introduction Utilities This section describes preinstalled utilities and tells how to start them. For details on operations, refer to each utility’s online manual, help files or readme.txt files. User’s Manual TOSHIBA Power Saver To access this power savings management program, click start, click the Control Panel, click Performance and Maintenance and select the TOSHIBA Power Saver icon.
Introduction TOSHIBA ConfigFree TOSHIBA ConfigFree is a suite of utilities to allow easy control of communication devices and network connections. TOSHIBA ConfigFree also allows you to find communication problems and create profiles for easy switching between locations and communication networks. To start ConfigFree, click start, point to All Programs, point to TOSHIBA, point to Networking and click ConfigFree.
Introduction User’s Manual TOSHIBA Touch and Launch TOSHIBA Touch and Launch is a tool that allows you to perform various tasks easily using the Touch Pad. TOSHIBA Touch and Launch is useful in the following conditions. ■ To open a file located on the desktop whose icon is obscured by a window. ■ To open a page contained in the Internet Explorer Favorites menu. ■ To display the list of currently open windows and change the active window.
Introduction Options You can add a number of options to make your computer even more powerful and convenient to use. The following options are available: 1-16 Memory expansion A 256, 512 or 1,024 MB memory module (DDR2 533) can easily be installed in the computer. Battery pack An additional battery pack can be purchased from your TOSHIBA dealer. Use it as a spare or replacement.
Qosmio G20 Chapter 2 The Grand Tour This chapter identifies the various components of your computer. Become familiar with each component before you operate the computer. Certain notebook chassis are designed to accommodate all possible configurations for an entire product series. Therefore, please be aware that your selected model may not have all the features and specifications corresponding to all of the icons or switches shown on the notebook chassis.
The Grand Tour Left side The following figure shows the computer’s left side. Microphone jack Modem jack USB ports Headphone jack Wireless communication switch The left side of the computer Modem jack The modem jack lets you use a modular cable to connect the modem directly to a telephone line. ■ In case of a lightning storm, unplug the modem cable from the telephone jack. ■ Do not connect the modem to a digital telephone line. A digital line will damage the modem. Universal Serial Bus (USB 2.
The Grand Tour Microphone jack A 3.5 mm mini microphone jack enables connection of a three-conductor mini jack for monaural microphone input. Headphone (S/PDIF) jack This jack lets you connect digital speakers or stereo headphones (16 ohm minimum). When you connect a digital speaker or headphones, the internal speakers are automatically disabled. This jack can be used also as S/PDIF jack and enables connection of optical digital correspondence apparatus.
The Grand Tour PC card slot This slot accommodates a 5 mm Type II card. The slot supports 16-bit PC cards and CardBus PC cards. PC card eject button Use this button to remove a PC card from the PC card slot. i.LINK (IEEE1394) port Connect an external device, such as a digital video camera to this port for high-speed data transfer. Back side The following figure shows the computer’s back side.
The Grand Tour S-Video out port This S-Video out port lets you transfer NTSC or PAL data to external devices. Refer to the TV section in Chapter 9, Optional Devices. D-Video out port This D-Video out port lets you transfer 525i (480i), 525p (480p), 1125i (1080i) or 750p (720p) data to external devices. Refer to the TV section in Chapter 9, Optional Devices. External monitor port This external monitor port lets you connect an external video display. Universal Serial Bus (USB 2.
The Grand Tour S-Video in port A camcorder or other recording device can be connected to your computer via an optional S-Video in cable for importing video data. Refer to the S-Video-in section in Chapter 9, Optional Devices. Monitor-in port Used for displaying video from your digital camcorder or video recorder on the internal LCD. This port can be used also as line-in port and enables connection of a stereo device for audio input. Refer to the Monitor-in section in Chapter 9, Optional Devices.
The Grand Tour User’s Manual Battery pack The battery pack powers the computer when the AC adaptor is not connected. For detailed information on the battery pack, refer to Chapter 6, Power. Battery release latch Slide and hold this latch to release the battery pack for removal. For detailed information on removing the battery packs, refer to Chapter 6, Power. Hard Disk Drive 1 This cover protects a hard disk drive pack, which can be removed and reinstalled.
The Grand Tour Front with the display open This section shows the front of the computer with the display open. Refer to the appropriate illustration for details. To open the display, push the display latch on the front of the display and lift up. Position the display at a comfortable viewing angle.
The Grand Tour Stereo speakers The speakers emit sound generated by your software as well as audio alarms generated by the system. Keep foreign objects out of the speakers. A pin or similar object can damage the computer's circuitry. User’s Manual Indicators(2) These LEDs let you monitor the hard disk drive activity, optical media drive activity, SD/SM and wireless communication status. Details are in the Indicators section.
The Grand Tour Touch Pad control buttons Control buttons below the Touch Pad let you select menu items or manipulate text and graphics designated by the on-screen pointer. LCD Sensor switch This switch senses when the LCD panel is closed or opened and activates the Panel Power Off/On feature. When you close the panel the computer enters Hibernation mode and shuts down. When you open the panel the computer starts in Hibernation mode. Use the TOSHIBA Power Saver Utility to enable or disable this feature.
The Grand Tour Indicators This section describes the indicators. System indicators The following indicators on the front of the computer can be monitored even when the display panel is closed. DC IN Power Battery System indicators (1) User’s Manual DC IN The DC IN indicator glows blue when DC power is supplied from the AC power adaptor. If the adaptor’s output voltage is abnormal or if the power supply malfunctions, this indicator flashes orange.
The Grand Tour Optical Media Drive HDD Bridge media slot Wireless communication System indicators (2) 2-12 HDD The Hard Disk Drive indicator glows blue when the computer is accessing the built-in hard disk Optical media drive The Optical media drive indicator glows blue when the computer is accessing a disk in the DVD Super Multi drive. Bridge media slot The Bridge media slot indicator glows blue when the computer is accessing the Bridge media slot.
The Grand Tour Keyboard indicators The figures below show the positions of the keypad overlay indicators and the Caps Lock indicator. The following indicator shows the state of an alphabet key (pressed or released). Caps Lock indicator Caps Lock indicator Caps Lock The Caps Lock indicator glows green when the alphabet keys are locked in uppercase. The following indicators show the status of the keypad overlay.
The Grand Tour Volume indicator This indicator employs a 6 stage lighting method to indicate the level of volume. By turning the volume dial you can turn the indicator lights on and off. If you want to increase the volume, move the dial from right to left (counterclockwise) and the 6 stages will flash in order. If you want decrease the volume, move the dial from left to right (clockwise) and the indicator lights will go out.
The Grand Tour Check the Disk-In-Use indicator when you use the floppy disk drive. Do not press the eject button or turn off the computer while the light is glowing. Doing so could destroy data and damage the floppy disk or the drive. ■ The external floppy disk drive should be placed on a flat, horizontal surface when in use. Do not set the drive on an incline greater than 20° while it is operating. ■ Do not set anything on top of the floppy disk drive.
The Grand Tour CDs ■ CD-R discs can be written only once. The recorded data cannot be erased or changed. ■ CD-RW discs, including multi speed CD-RW discs, high-speed CD-RW discs and ultra-speed CD-RW discs can be recorded more than once. DVDs ■ DVD-R and DVD+R discs can be written only once. The recorded data cannot be erased or changed. ■ DVD-RW, DVD+RW and DVD-RAM discs can be recorded more than once.
The Grand Tour AC adaptor The AC adaptor can automatically adjust to any voltage ranging from 100 to 240 volts and to a frequency of either 50 or 60 hertz, enabling you to use this computer in almost any country/region. The adaptor converts AC power to DC power and reduces the voltage supplied to this computer. To recharge the battery, simply connect the AC adaptor to a power source and the computer. Refer to Chapter 6, Power, for details.
The Grand Tour 2-18 User’s Manual
Qosmio G20 Chapter 3 Getting Started This chapter provides basic information to get you started using your computer. It covers the following topics: ■ Setting up your work space — for your health and safety Be sure also to read the Safety Instruction Manual. This guide, which is included with the computer, explains product liability.
Getting Started General conditions In general, if you are comfortable, so is your computer, but read the following to make sure your work site provides a proper environment. ■ Make sure there is adequate space around the computer for proper ventilation. ■ Make sure the AC power cord connects to an outlet that is close to the computer and easily accessible. ■ The temperature should be 5 to 35 degrees Centigrade (41 to 95 degrees Fahrenheit) and the relative humidity should be 20 to 80 percent.
Getting Started Seating and posture The height of your chair in relation to the computer and keyboard as well as the support it gives your body are primary factors in reducing work strain. Refer to the following tips. Below eye level 90°angles Foot rest Posture and positioning of the computer ■ Place your chair so that the keyboard is at or slightly below the level of your elbow. You should be able to type comfortably with your shoulders relaxed. ■ Your knees should be slightly higher than your hips.
Getting Started Work habits A key to avoiding discomfort or injury from repetitive strain is to vary your activities. If possible, schedule a variety of tasks into your workday. If you must spend long periods at the computer, finding ways to break up the routine can reduce stress and improve your efficiency. ■ Sit in a relaxed posture. Good positioning of your chair and equipment as described earlier can reduce tension in your shoulders or neck and ease back strain. ■ Vary your posture frequently.
Getting Started ■ Use only the AC adaptor supplied with your computer or an equivalent adaptor that is compatible. Use of any incompatible adaptor could damage your computer. TOSHIBA assumes no liability for any damage caused by use of an incompatible adaptor. ■ The supplied power cord conforms to safety rules and regulations in the region the product is bought and should not be used outside this region.
Getting Started Opening the display The display panel can be rotated in a wide range of angles for optimal viewing. 1. Push the display latch on the front of the computer to unlatch the display panel. 2. While holding down the palm rest with one hand so that the main body is not raised, lift the panel slowly. Adjust the angle of the panel to provide optimal clarity. Use reasonable care when opening and closing the display panel. Opening it vigorously or slamming it shut could damage the computer.
Getting Started 2. Press and hold the computer’s power button for two or three seconds. Power button Turning on the power Starting up for the first time When you first turn on the power, the computer’s initial screen is the Microsoft Windows XP Startup Screen Logo. Follow the on-screen directions for each screen. During setup, you can click the Back button to return to the previous screen. Be sure to read the License Agreement carefully.
Getting Started Hibernation mode The Hibernation Mode feature saves the contents of memory to the hard disk when the computer is turned off. The next time the computer is turned on, the previous state is restored. The Hibernation Mode feature does not save the status of any peripheral devices. ■ Save your data. While entering Hibernation Mode, the computer saves the contents of memory to the hard disk drive. However, for safety sake, it is best to save your data manually.
Getting Started Automatic Hibernation The computer will enter Hibernate mode automatically when you press the power button or close the lid. First, however, make the appropriate settings according to the steps below. 1. Click start and open the Control Panel. 2. Open Performance and Maintenance and open Power Options. 3. Select the Hibernate window in the Power Options Properties, select the Enable hibernation check box and click the Apply button. 4. Open TOSHIBA Power Saver. 5.
Getting Started ■ Before entering Standby mode, be sure to save your data. ■ Do not install or remove a memory module while the computer is in Standby Mode. The computer or the module could be damaged. ■ Do not remove the battery pack while the computer is in Standby Mode (unless the computer is connected to an AC power source). Data in memory will be lost.
Getting Started Standby limitations Standby will not function under the following conditions: ■ Power is turned back on immediately after shutting down. ■ Memory circuits are exposed to static electricity or electrical noise. Restarting the computer Certain conditions require that you reset the system. For example, if: ■ You change certain computer settings. ■ An error occurs and the computer does not respond to your keyboard commands. There are three ways to reset the computer system: 1.
Getting Started Restoring QosmioPlayer To restore QosmioPlayer, follow the steps below. 1. Load the QosmioPlayer Recovery CD in the optical media drive and turn off the computer’s power. 2. Hold down the F12 key and turn on the power. When Qosmio appears, release the F12 key. 3. Use the left or right cursor key to select the optical media drive in the Boot Devices menu. For details, refer to the Boot Priority section in Chapter 7, HW Setup. 4. Follow the on-screen instructions.
Qosmio G20 Chapter 4 Operating Basics This chapter gives information on basic operations including using the Touch Pad, the USB floppy disk drive (optional), TV Tuner (optional), Sound System, Modem, Wireless communication features and LAN. It also provides tips on care of the computer, floppy disks and CD/DVDs. Using the Touch Pad To use the Touch Pad, simply touch and move your finger tip across it in the direction you want the on-screen pointer to go.
Operating Basics Using the USB floppy disk drive (optional) An optional USB floppy disk drive connects to the computer’s USB port. It accommodates 1.44-megabyte or 720-kilobyte floppy disks. Refer to Chapter 2, The Grand Tour, for more information. Connecting USB floppy disk drive To connect the drive, plug the floppy disk drive’s USB connector into one of the computer’s USB ports. Make sure the connector is right side up and properly aligned with the socket.
Operating Basics TV Tuner (optional) Some models in this series are equipped with a built-in TV Tuner that allows you to watch TV programs on the built-in LCD and to record them. If you have Windows XP Home Edition installed, use the WinDVR program to display TV programs on the built-in LCD and record them. It is also possible to edit recorded programs and save them on a DVD. If you have Windows XP Media Center Edition isntalled, use the My TV feature contained in Media Center.
Operating Basics 2. Connect the antenna adaptor to the TV antenna port of your computer. TV antenna port Antenna adaptor Connecting the antenna adaptor 3. Connect the antenna cable to the other end of the antenna adaptor. Antenna adaptor Antenna cable Connecting the antenna cable When you have been using a descrambler to receive the programs on cable TV or satellite broadcasting, connect the descrambler to the antenna cable.
Operating Basics Precautions when using WinDVR Refer to the online help of WinDVR for details. ■ TV programs or other visual sources that have been recorded with WinDVR can be used for personal uses only. ■ When WinDVR is running, do not change the screen resolution or the color depth setting. ■ Before recording or editing video or sound which is important to you, run a test session to see if your operations work correctly. ■ Scheduled video recording is not available when your computer is powered off.
Operating Basics ■ WinDVR must be installed using the Administrator account. ■ When two sequential scheduled recording sessions have been reserved, the first session will terminate about 2 minutes before the specified end time. This is because the second session needs a time for preparation (For example, if two recording sessions of 1:00-2:00pm and 2:00-3:00pm have been booked, the 1:00-2:00pm session will terminate about 2 minutes earlier, that is, at about 1:58pm).
Operating Basics SoundMAX control panel The SoundMAX control panel lets you control additional functions for the Microphone Enhancement and Audio Power Management. To launch the SoundMAX Control Panel, follow the steps below. 1. Click start and click Control Panel. 2. If you are viewing the Control Panel in Category View, click on Switch to Classic View. 3. Double-click the SoundMAX icon. The Microphone Setup allows you to optimize the microphone input settings for your particular configuration.
Operating Basics Writing CDs/DVDs on DVD Super Multi drive The following applications for writing are provided : RecordNow!, and DLA licensed by Sonic Solutions, and InterVideo's WinDVD Creator Platinum. Important message Before you write or rewrite to CD-R/RW or DVD-R/-RW/+R/+RW/-RAM discs, read and follow all setup and operating instructions in this section. If you fail to do so, the DVD Super Multi drive may not function properly, and you may fail to write or rewrite, lose data or incur other damage.
Operating Basics DVD-R: DVD Specifications for Recordable Disc for General Version 2.0 TAIYO YUDEN CO., LTD. Matsushita Electric Industrial Co., Ltd DVD+R: MITSUBISHI CHEMICAL CORPORATION RICOH Co., Ltd. DVD+R DL: (Double Layer Recordable drive only) MITSUBISHI CHEMICAL CORPORATION DVD-RW: DVD Specifications for Recordable Disc for Version 1.1 or version 1.2 VICTOR COMPANY OF JAPAN.LIMITED MITSUBISHI CHEMICAL CORPORATION DVD+RW: MITSUBISHI CHEMICAL CORPORATION RICOH Co., Ltd.
Operating Basics ■ Data deleted (erased) from a CD-RW, DVD-RW, DVD+RW and DVD-RAM disc cannot be recovered. Check the content of the disc carefully before you delete it. If multiple drives that can write data to discs are connected, be careful not to delete data from the wrong drive. ■ In writing to a DVD-R/-RW, DVD+R/+RW or DVD-RAM disc, some disc space is required for file management, so you may not be able to write the full capacity of the disc.
Operating Basics When writing or rewriting Please observe/consider the following when you write or rewrite to a CD-R/RW, DVD-R/-RW/-RAM or DVD+R/+RW disc. ■ Do not perform any of the following actions when writing or rewriting: ■ Change users in the Windows XP operating system. ■ Operate the computer for any other function, including using a mouse or Touch Pad or closing/opening the LCD panel. ■ Start a communication application such as a modem. ■ Apply impact or vibration to the computer.
Operating Basics RecordNow! Basic for TOSHIBA Note the following limitations when you use RecordNow!: ■ DVD-Video cannot be created using RecordNow!. ■ DVD-Audio cannot be created using RecordNow!. ■ You cannot use RecordNow!'s “Audio CD for Car or Home CD Player” function to record music to DVD-R/-RW or DVD+R/+RW discs. ■ Do not use the “Exact Copy” function of RecordNow! to copy DVD-Video and DVD-ROM with copyright protection.
Operating Basics Data Verification To verify that data is written or rewritten correctly, follow the steps below before you write or rewrite a Data CD/DVD. 1. Click the Options button( ) on the RecordNow! Console to open the Options panels. 2. Select the Data in the left-side menu. 3. Mark the Verify data written to the disc after burning check box in the Data Options. 4. Click the OK button.
Operating Basics When using WinDVD Creator Platinum You can record video back to your digital camcorder via i.LINK (IEEE1394) using WinDVD Creator Platinum. However, there is a case where you may find that playback sound is choppy - if this is the case follow the below instructions: 1. Click start and select the Control Panel. 2. Click the Performance and Maintenance icon in the Control Panel. 3. Click the System icon in the Performance and Maintenance window. 4.
Operating Basics Important information for use Note the following limitations when you write video DVD: 1. Editing digital video ■ Log in with Administrator rights to use WinDVD Creator. ■ Make sure that your computer is running on AC power when using WinDVD Creator. ■ Operate the computer at Full Power. Do not use power-saving features. ■ While you are editing a DVD, you can display previews. However, if another application is running, the preview might not display properly.
Operating Basics 2. Before recording the video to DVD ■ When you record to DVD discs, please use only media recommended by TOSHIBA. ■ Do not set the working drive to a slow device like a USB 1.1 hard disk drive or it will fail to write DVD. ■ Do not perform any of the following actions: ■ Operate the computer for any other function, including using a mouse or TouchPad or closing/opening the LCD panel. ■ Bump or cause vibration to the computer.
Operating Basics Media care This section provides tips on protecting data stored on your CD/DVDs and floppy disks. Handle your media with care. The following simple precautions will increase the lifetime of your media and protect the data stored on them: CD/DVDs 1. Store your CD/DVDs in the container they came in to protect them and keep them clean. 2. Do not bend the CD/DVD. 3. Do not write on, apply a sticker to, or otherwise mar the surface of the CD/DVD that contains data. 4.
Operating Basics Modem This section describes how to connect and disconnect the internal modem to and from a telephone jack. The internal modem does not support voice functions. All data and fax functions are supported. ■ In case of a lightning storm, unplug the modem cable from the telephone jack. ■ Do not connect the modem to a digital telephone line. A digital line will damage the modem.
Operating Basics Setting You can enable or disable the following settings: AutoRun Mode The Region Select utility starts automatically when you start up the operating system. Open the Dialing Properties dialog box after selecting region. The dialing properties dialog box will be displayed automatically after you select the region. Location list for region selection. A submenu appears displaying location information for telephony.
Operating Basics Connecting To connect the modular cable, follow the steps below. The modular cable that comes with the computer must be used to connect a modem. Connect the end of the modular cable with the core to the computer. ■ In case of a lightning storm, unplug the modular cable from the telephone jack. ■ Do not connect the modem to a digital telephone line. A digital line will damage the modem. 1. Plug one end of the modular cable into the computer’s modem jack. 2.
Operating Basics Wireless communications The computer’s wireless communication function supports both Wireless LAN and Bluetooth devices. Bluetooth is provided with some models. Wireless LAN The Wireless LAN is compatible with other LAN systems based on Direct Sequence Spread Spectrum/Orthogonal Frequency Division Multiplexing radio technology that complies with IEEE802.11 Wireless LAN standard (Revision A, B or G) and Turbo Mode. Supported features.
Operating Basics Security ■ TOSHIBA strongly recommend that you enable WEP (encryption) functionality, otherwise your computer will be open to illegal access by an outsider using a wireless connection. If this occurs, the outsider may illegally access your system, eavesdrop, or cause the loss or destruction of stored data. ■ TOSHIBA is not liable for the loss of of data due to eavesdropping or illegal access through the wireless LAN and the damage thereof.
Operating Basics Release Notes related to the BluetoothTM Stack for Windows® by TOSHIBA 1. Install: On Windows 2000 or Windows XP, BluetoothTM Stack for Windows® by TOSHIBA is not digitally signed, although it should be noted that this does not affect its usage or operation in any way. 2. Fax application software: You may find that you cannot use the BluetoothTM Stack software in conjunction with some facsimile communications applications. 3.
Operating Basics LAN The computer has built-in support for Ethernet LAN (10 megabits per second, 10BASE-T) and Fast Ethernet LAN (100 megabits per second, 100BASE-TX). This section describes how to connect/disconnect to a LAN. LAN cable types The computer must be configured properly before connecting to a LAN. Logging onto a LAN using the computer’s default settings could cause a malfunction in LAN operation. Check with your LAN administrator regarding set-up procedures.
Operating Basics 3. Plug the other end of the cable into a LAN hub connector. Check with your LAN administrator before connecting to a hub. When the computer is exchanging data with the LAN, the LAN Active indicator glows orange. When the computer is connected to a LAN hub but is not exchanging data, the Link indicator glows green. Disconnecting LAN cable To disconnect the LAN cable, follow the steps below.
Operating Basics Moving the computer The computer is designed for rugged durability. However, a few simple precautions taken when moving the computer will help ensure trouble-free operation. ■ Make sure all disk activity has ended before moving the computer. Check the HDD indicator on the computer. ■ If a CD/DVD is in the drive, remove it. Also make sure the drawer is securely closed. ■ Turn off the power to the computer. ■ Disconnect the AC adaptor and all peripherals before moving the computer.
Qosmio G20 Chapter 5 The Keyboard The computer’s keyboard layouts are compatible with a 101/102-key enhanced keyboard. By pressing some keys in combination, all the 101/102-key keyboard functions can be executed on the computer. The number of keys on your keyboard depends on which country/region’s keyboard layout your computer is configured with. Keyboards for numerous languages are available. There are five types of keys: typewriter keys, keypad overlay, function keys, soft keys and cursor control keys.
The Keyboard Function keys: F1 … F12 The function keys (not to be confused with Fn) are the 12 keys at the top of your keyboard. These keys function differently from other keys. F1 through F12 are called function keys because they execute programmed functions when pressed. Used in combination with the Fn key, keys marked with icons execute specific functions on the computer. Refer to the section, Soft keys: Fn key combinations, in this chapter.
The Keyboard Press Fn + F10 or Fn + F11 to access the integrated keypad. When activated, the keys with gray markings on the bottom edge become numeric keypad keys (Fn + F11) or cursor control keys (Fn + F10). Refer to the Keypad overlay section in this chapter for more information on how to operate these keys. The power on default for both settings is off. Press Fn + F12 (ScrLock) to lock the cursor on a specific line. The power on default is off.
The Keyboard Instant security: Press Fn + F1 to blank the screen to prevent others from accessing your data. To restore the screen and original settings, press any key or press the Touch Pad. If a screensaver password is registered, a dialog box will appear. Enter the screensaver password and click OK. If no password is set, the screen will be restored when you press any key or press the Touch Pad. In Monitor-in mode, Fn + F1 is not available. Power save mode: Pressing Fn + F2 changes the power save mode.
The Keyboard Display selection: Press Fn + F5 to change the active display device. When you press these hot keys, a dialog box appears. Only selectable devices will be displayed. Hold down Fn and press F5 again to change the device. When you release Fn and F5, the selected device will change. If you hold down these hot keys for five seconds the selection will return to LCD. In Monitor-in mode, Fn + F5 is not available.
The Keyboard Wireless setting: If your computer has both Bluetooth and Wireless LAN functions, you can press Fn + F8 to select which type of wireless communication you want to use. When you press these hot keys, a dialog box will appear. Continue holding down Fn and press F8 to change the setting. If wireless communication is turned off, Disabled Wireless Communication Switch will be displayed. If no wireless communication device is installed, no dialog box will appear.
The Keyboard QosmioEngine modes: Press Fn + 3 to change the QosmioEngine screen mode on Dynamic, Standard or Theater. Refer to the QosmioPlayer section in Chapter 8, Using the Remote Controller, Front operation panel and QosmioPlayer. Monitor-in: Pressing Fn + 4 will toggle mode between Windows and AV Input. In Monitor-in mode, both CD/DVD and Digital Audio indicators are on and the Audio button is disabled. Pressing these hot keys in the power-off condition will do nothing.
The Keyboard Turning on the overlays The numeric keypad overlay can be used for numeric data input or cursor and page control. Arrow mode To turn on the Arrow mode, press Fn + F10. The Arrow mode F10 indicator lights. Now try cursor and page control using the keys shown in the figure below. Press Fn + F10 again to turn off the overlay. Numeric mode To turn on the Numeric mode, press Fn + F11. The Numeric mode F11 indicator lights. Now try numeric data entry using the keys shown in the figure below.
The Keyboard Temporarily using overlay (overlay off) While using the normal keyboard, you can temporarily use the keypad overlay without turning it on: 1. Press and hold down Fn. 2. Check the keyboard indicators. Pressing Fn turns on the most recently used overlay. If the Numeric mode indicator lights, you can use the overlay for numeric entry. If the Arrow mode indicator lights, you can use the overlay for cursor and page control. 3. Release Fn to return to normal keyboard operation.
The Keyboard 5-10 User’s Manual
Qosmio G20 Chapter 6 Power The computer’s power resources include the AC adaptor and internal batteries. This chapter gives details on making the most effective use of these resources including charging and changing batteries, tips for saving battery power, and power up modes. Power conditions The computer’s operating capability and battery charge status are affected by the power conditions: whether an AC adaptor is connected, whether a battery is installed and what the charge level is for the battery.
Power Table 6-1 Power conditions continued Power on AC adaptor not connected 6-2 Battery charge is above low battery trigger point • Operates • LED: Battery off DC IN off Battery charge is below low battery trigger point • Operates • LED: Battery flashes orange DC IN off Battery charge is exhausted Computer goes into Standby Mode and shuts down No battery installed • Cannot operate • LED: Battery off DC IN off Power off (no operation) User’s Manual
Power Power indicators As shown in the above table, the Battery, DC IN and Power indicators on the system indicator alert you to the computer’s operating capability and battery charge status. Battery indicator Check the Battery indicator to determine the status of the battery pack. The following indicator lights indicate the battery status: Flashing orange The battery charge is low. The AC adaptor must be connected to recharge the battery.
Power Power indicator Check the Power indicator to determine the power status: Blue Indicates power is being supplied to the computer and the computer is turned on. Blinking orange Indicates power is being supplied to the computer while the computer is in Standby mode. The indicator turns on for one second and off for two seconds. No light Under any other conditions, the indicator does not light.
Power Real Time Clock battery The Real Time Clock (RTC) battery provides power for the internal real time clock and calendar. It also maintains the system configuration. If the RTC battery becomes completely discharged, the system loses this data and the real time clock and calendar stop working. The following message appears when you turn on the power: S **** RTC battery is low or CMOS checksum is inconsistent **** Press [F1] key to set Date/Time.
Power 3. Never short-circuit the battery pack by contacting the terminals with a metal object. A short-circuit can cause fire or otherwise damage the battery pack and possibly cause injury. To avoid accidental short-circuit, always wrap the battery pack in plastic and cover the terminals with electrical tape when storing or disposing of the battery pack. 4. Never puncture the battery pack with a nail or other sharp object. Never strike it with a hammer or other object. Never step on it. 5.
Power Caution 1. Never continue to use a battery pack after its recharging capacity has become impaired, or after the display of a warning message indicating that the battery pack’s power is exhausted. Continued use of an exhausted or impaired battery pack could cause the loss of data. 2. Never dispose of battery packs with normal trash. Bring them to your TOSHIBA dealer or to another recycling center to save resources and prevent environmental damage.
Power Charging the batteries When the power in the battery pack becomes low, the Battery indicator flashes orange indicating that only a few minutes of battery power remain. If you continue to use the computer while the Battery indicator flashes, the computer enables Hibernation mode (so you don’t lose data) and automatically turns off. The computer enters Hibernate mode only if Hibernation is enabled in two places: the Hibernate tab in Power Options and Setup Action tab in TOSHIBA Power Saver.
Power Battery charging notice The battery may not charge right away under the following conditions: ■ The battery is extremely hot or cold. If the battery is extremely hot, it might not charge at all. To ensure the battery charges to its full capacity, charge the battery at room temperature of 10° to 30°C (50° to 88°F). ■ The battery is nearly completely discharged. Leave the AC adaptor connected for a few minutes and the battery should begin charging.
Power Maximizing battery operating time A battery’s usefulness depends on how long it can supply power on a single charge. How long the charge lasts in a battery depends on: ■ How you configure the computer (for example, whether you enable battery-power saving options). The computer provides a battery save mode, which can be set in TOSHIBA Power Saver, to conserve battery power.
Power Extending battery life To maximize the life of your battery pack: ■ At least once a month, disconnect the computer from a power source and operate it on battery power until the battery pack fully discharges. Before doing so, follow the steps below. 1. Turn off the computer’s power. 2. Disconnect the AC adaptor and turn on the computer’s power. If it does not turn on go to step 4. 3. Operate the computer on battery power for five minutes.
Power Removing the battery pack To replace a discharged battery, follow the steps below. ■ When handling battery packs, do not short-circuit the terminals. Also do not drop, hit or otherwise apply impact; do not scratch or break the casing and do not twist or bend the battery pack. ■ Do not remove the battery pack while the computer is in Standby mode. Data is stored in RAM, so if the computer loses power it will be lost.
Power Installing the battery pack To install a battery, follow the steps below. ■ The battery pack is a lithium ion battery, which can explode if not properly replaced, used, handled or disposed of. Dispose of the battery as required by local ordinances or regulations. Use only batteries recommended by TOSHIBA as replacements. ■ Do not touch the release latch while holding the computer - this may cause the battery pack to be unintentionally released which may result in injury or damage. 1. 2. 3. 4.
Power 6. Slide the battery safety lock to the Lock ( ) position. Battery pack Battery safety lock Lock the battery safety lock 7. Return your computer to the upright position. TOSHIBA Password Utility The TOSHIBA Password Utility provides two levels of password security: User and Supervisor. Passwords set in TOSHIBA Password Utility are different from the Windows password.
Power ■ Owner String (text box) You can use this box to associate text with the password. After you enter the text, click Apply or OK. When you switch the computer on, this text will be displayed, for example, to prompt the user to enter the password. Supervisor password To set a supervisor password, follow the steps below. 1. Click start. 2. Click Run. 3. Enter the following: C:\Program Files\Toshiba\Windows Utilities\SVPWTool\TOSPU.
Power Power-up modes The computer has the following power-up modes: ■ Boot: Computer shuts down without saving data. Always save your work before you turn the computer off in boot mode. ■ Hibernation: Data in memory is saved to the hard disk. ■ Standby: Data is maintained in the computer’s main memory. Refer also to the sections Turning on the power and Turning off the power in Chapter 3, Getting Started.
Qosmio G20 Chapter 7 HW Setup This chapter explains how to use TOSHIBA HW Setup program to configure your computer, and provides information on setting up the Execute-Disable Bit Capability and the front panel operation. Accessing HW Setup To run HW Setup, click start, click Control Panel, click Printers and Other Hardware and select TOSHIBA HW Setup.
HW Setup Display This tab lets you customize your computer’s display settings for either the internal LCD screen or for an external monitor. Power On Display Lets you select the display to be used when the computer is booted this setting is only available with standard VGA modes and cannot be configured through the Windows Desktop properties Auto-Selected Selects an external monitor if one is connected. Otherwise, it selects the internal LCD (Default).
HW Setup HDD −> FDD −> CD-ROM −> LAN The computer looks for bootable files in the following order: HDD, floppy disk drive, CD-ROM and LAN. (Default) FDD −> HDD −> CD-ROM −> LAN The computer looks for bootable files in the following order: floppy disk drive, HDD, CD-ROM and LAN. HDD −> CD-ROM −> LAN −> FDD The computer looks for bootable files in the following order: HDD, CD-ROM, LAN and floppy disk drive.
HW Setup 3. Use the left/right cursor keys to highlight the boot device you want and press Enter. ■ If only a Supervisor Password has been set, the following should be noted: ■ The boot device menu will appear when you use the user password to start the computer and the 'Able to run HW Setup' option has been configured. ■ The boot device menu will not appear when you use the user password to start the computer and the 'Unable to run HW Setup' option has been configured.
HW Setup Network Boot Protocol This feature sets the protocol to remotely boot from the network. [PXE] Sets PXE as the protocol (Default). [RPL] Sets RPL as the protocol. Keyboard Wake-up on Keyboard When this feature is enabled and the computer is in Standby mode, you can turn on the computer by pressing any key. It is effective only for the internal keyboard and only when the computer is in standby mode. Enabled Enables the Wake-up on Keyboard function.
HW Setup Device Config Device Configuration This option lets you set the device configuration. All Devices BIOS sets all devices. Setup by OS Operating system sets devices that it can control (Default). PCI Express Link ASPM This feature lets you set the PCI Express power-saving configuration. Enabled Enables power-saving when the PCI Express device is not being used. Disabled Disables power-saving for performance.
HW Setup Button Setting Sound Logo Use this option to enable or disable the startup sound when the computer is switched on. Enabled Enables startup sound (Default) Disabled Disables startup sound. Start Up logo This option lets you select from the following two types of logo which can be displayed when the computer starts up. Animation The Logo appears as an animated image (Default). Picture The Logo appears as a static image.
HW Setup Starting and Ending the BIOS Setup Program Starting the BIOS Setup Program 1. Switch on your computer while pressing the Esc key. If “Password =” is displayed, enter either the Supervisor Password, if one is set, or the User Password and press the Enter key. The “Check system. Then press [F1] key.” message is displayed. 2. Press the F1 key. The BIOS setup program will start up. Select the Execute-Disable Bit Capability or Front Operation Panel item to make changes.
HW Setup Front Operation Panel The configuration of the computer's front panel is controlled through the following settings shown on the first page of the setup screen. Front Operation Panel This setting activates and deactivates the Front Operation Panel. Front Operation Panel Enabled. Front Operation Panel Disabled (Default). Beep Volume With this setting, when the button is pushed, the beep volume changes. Beep Volume Off. Beep Volume Low. Beep Volume Medium (Default). Beep Volume High.
HW Setup 7-10 User’s Manual
Qosmio G20 Chapter 8 Using the Remote Controller, Front operation panel and QosmioPlayer This chapter explains how to use the Remote Controller on TV Tuner models (both under Windows XP Media Center Edition and Windows XP Home Edition) as well as provides information about QosmioPlayer. The state where Windows XP is active is referred to as Windows mode, whereas the state where QosmioPlayer is active is referred to as QosmioPlayer mode.
Using the Remote Controller, Front operation panel and QosmioPlayer QosmioPlayer QosmioPlayer is a quick play feature that enables users to perform TV, DVD and CD playback, as well as AV input (image and voice data) without using Windows. QosmioPlayer is provided with some models. To use the QosmioPlayer feature, some settings must be specified. For more information on how to configure, refer to the chapter on the QosmioPlayer Setting in the User’s Manual.
Using the Remote Controller, Front operation panel and QosmioPlayer CD/DVD Full screen Power Skip TV Brightness Input switching Time shift Replay Numbers DVD Menu Option selection OK Arrows Back Set up Record Volume Channel Mute Fast forward Fast rewind Stop Play/Pause Next Previous Audio Display Angle Subtitle Remote Controller User’s Manual 8-3
Using the Remote Controller, Front operation panel and QosmioPlayer 8-4 Power Starts or terminates the operating system, and terminates QosmioPlayer Play. TV Starts or terminates Software for TV. Starts QosmioPlayer (TV). CD/DVD Starts Qosmio interface, Windows Media Player, WinDVD, QosmioPlayer (CD), and/or QosmioPlayer (DVD). Input switching Toggles between the video input signals (TV antenna/S-Video/composite).
Using the Remote Controller, Front operation panel and QosmioPlayer User’s Manual Numbers Allows you to select a channel or chapter number while watching TV, or CD/DVD replay. To select a channel or chapter number of two or more digits, press the buttons sequentially. For example, press the “1” button and then the “0” button to select the number 10. DVD Menu Displays the top menu in DVD replay. Arrows Moves the cursor between options.
Using the Remote Controller, Front operation panel and QosmioPlayer Fast rewind Rewinds the video quickly when replaying DVD's or rewinds the audio by about 10 seconds when using QosmioPlayer (CD). Fast forward Forwards the video quickly when replaying DVD's or skips the audio backwards by about 10 seconds when using QosmioPlayer (CD). Stop Stops playing music or video. Previous Plays the previous track (CD) or chapter (DVD). Next Plays the next track (CD) or chapter (DVD).
Using the Remote Controller, Front operation panel and QosmioPlayer CD/DVD F11 Terminates QosmioPlayer (TV) -> Starts QosmioPlayer (CD or DVD) - - INPUT (Input switching) l TV antenna/SVideo/composite - - Fn + F7 Increases the brightness Increases the brightness Increases the brightness Fn + F6 Decreases the brightness Decreases the brightness Decreases the brightness (Brightness) (Brightness) TIME SHIFT Ctrl + T - - REPLAY Ctrl + K - - Rewinds by about 10 seconds SKIP Ctrl + L
Using the Remote Controller, Front operation panel and QosmioPlayer 8 8 Select a channel 8 Select a track 8 Select a chapter 8 9 9 Select a channel 9 Select a track 9 Select a chapter 9 0 1, 0 Select a channel 10 0 - Normally functions as “0” Normally functions as “0” - 1, 1 Select a channel 11 - - - 1, 2 Select a channel 12 - - - - Displays the top menu Move the cursor - Move the cursor Move the cursor - Move the cursor Move the cursor - Move the cursor Move the curs
Using the Remote Controller, Front operation panel and QosmioPlayer VOL + (Volume) Ctrl + Increases the volume Increases the volume Increases the volume VOL (Volume) Ctrl + Decreases the volume Decreases the volume Decreases the volume REC Ctrl + R - - - Mute the volume Mute the volume Mute the volume - Rewinds by about 10 seconds Rewinds quickly - Skip by about 10 seconds Forwards quickly K - Previous title Previous chapter L - Next title Next chapter Space - Play or paus
Using the Remote Controller, Front operation panel and QosmioPlayer - F1 - E - F9 or Tab - SELECT (Option selection) Display the keyguide Display the keyguide Display the keyguide Open the disk tray Open the disk tray - - Windows XP Media Center Edition This section describes the Remote Controller provided with a Windows XP Media Center Edition model. You can use your remote control with Media Center to play CDs, DVDs and videos; to view pictures; and to watch and record television programs.
Using the Remote Controller, Front operation panel and QosmioPlayer My music My pictures Power Access indicator My TV My videos Stop Pause Play Record Fast Forward Rewind Skip More info Replay Back OK Start Arrows Volume + Channel/Page Volume Mute Recorded TV DVD Menu Live TV Guide Numbers Enter Clear Remote Controller User’s Manual 8-11
Using the Remote Controller, Front operation panel and QosmioPlayer 8-12 Power Starts or terminates the operating system. This button functions like the Power button of your computer. By default, the Standby mode is equivalent to the Power Off state of your computer. To change the setting, click start, select Control panel -> Performance and Maintenance ->TOSHIBA Power Saver -> Setup Action -> Manual Setup.
Using the Remote Controller, Front operation panel and QosmioPlayer User’s Manual Replay Moves media backward (seven seconds for videos and live TV, one music track or one DVD chapter at a time). Skip Moves media forward (30 seconds for videos and live TV, one music track or one DVD chapter). Back Displays the previous window. Arrows Moves the cursor to navigate within Media Center windows. OK Selects the desired action or window option. It acts like the Enter Key.
Using the Remote Controller, Front operation panel and QosmioPlayer Numbers Allows you to select a channel or chapter number while watching TV, or CD/DVD replay. Numbers can be entered. To select a channel or chapter number of two or more digits, press the buttons sequentially. For example, press the “1” button and then the “0” button to select the number 10. Clear Deletes entered numbers. Enter The OK button on the Remote Controller has the same functions.
Using the Remote Controller, Front operation panel and QosmioPlayer Front operation panel (Non TV Tuner model) User’s Manual TV button Starts or terminates Software for TV. CD/DVD button Pressing this button will launch an application program that allows you to watch a DVD or listen to a CD. If you press this button while the computer is switched off, it will launch either QosmioPlayer (DVD) or QosmioPlayer (CD).
Using the Remote Controller, Front operation panel and QosmioPlayer 8-16 Brightness up button Use this button to increase the brightness of the built-in LCD. Monitor-in button The Monitor-in button is provided with some models. Pressing this button will toggle the computer between displaying the Windows operating system and the AV input. In this mode, both the DVD/CD and Digital Audio indictors are on and the Audio button is disabled.
Using the Remote Controller, Front operation panel and QosmioPlayer Function comparison list for TV/DVD/CD software Windows mode Icon User’s Manual Front operation panel Software for TV (TV) TV Activate Software for TV WinDVD (DVD) Windows Media Player 10 (CD) - - CD/DVD - Detect and activate media Detect and activate media Play/Pause - Detect and activate media or Play/Pause Detect and activate media or Play/Pause Stop - Stop Stop Previous - Previous chapter Previous track Next
Using the Remote Controller, Front operation panel and QosmioPlayer QosmioPlayer mode Eleven buttons are available for use: TV Tuner model: TV, CD/DVD, Play/Pause, Stop, Previous, Next, Record, Brightness up, Brightness down, Monitor-in, TV-out. Non TV Tuner model: Internet, CD/DVD, Play/Pause, Stop, Previous, Next, TV-out, Brightness up, Brightness down, Zoom out (-), Zoom in (+). These buttons allow you to manage Audio/Video functions, run applications and access utilities.
Using the Remote Controller, Front operation panel and QosmioPlayer Function comparison list for TV/DVD/CD software QosmioPlayer mode Icon Front operation panel View QosmioPlayer (TV) Play QosmioPlayer (CD/DVD) TV Activate TV application Terminate (CD/DVD) Start (TV) CD/DVD Terminate (TV) Start (CD/DVD) Detect and activate media Play/Pause - Play/Pause Stop - Stop Previous This button does not function during QosmioPlayer (TV) mode.
Using the Remote Controller, Front operation panel and QosmioPlayer Using the Remote Controller Remote Controller is provided with TV Tuner models only. This computer includes a remote control unit, which allows you to control some of your computer’s functions from a distant location. ■ The Remote Controller is designed specifically for this computer. ■ Some application programs may not support remote control functions.
Using the Remote Controller, Front operation panel and QosmioPlayer 2. Connect the external infrared Remote control receiver to one of the computer's USB ports. Proceed to Step 3 if you are a subscriber of satellite or CATV. USB port Connecting the USB cable to the computer’s USB port 3. Connect the infrared transmitter cable to the external infrared Remote control receiver. Please note that the infrared remote control for your set-top box must be compatible in order to function.
Using the Remote Controller, Front operation panel and QosmioPlayer Operational range of the remote control Remote Controller is provided with TV Tuner models. Point the remote control at your computer and press a button. The operational angle and distance are described below. Distance Within 5 m from the infrared receiver window. Angle Within about 30 degrees horizontally and about 15 degrees vertically of perpendicular to the infrared receiver window.
Using the Remote Controller, Front operation panel and QosmioPlayer Disabling the remote control (Windows XP Home Edition model only) Follow the steps below to disable the remote control features 1. Open the Control Panel and click the Printer and Other Hardware icon. 2. Click the TOSHIBA Control option. The Property of the TOSHIBA Control screen appears. 3. In the Remote Control tab, uncheck the Use Remote Control check box. Turn on this check box to use the Remote Controller. 4. Click the OK button.
Using the Remote Controller, Front operation panel and QosmioPlayer Installing/Removing batteries Be sure to install the dry batteries provided with this product before using the Remote Controller. The procedures for installing and removing the batteries vary depending on the type of the Remote Controller. Check the type and then install or remove the batteries as instructed. Store the battery for the remote control beyond the reach of children. If a child swallows a battery, this might result in choking.
Using the Remote Controller, Front operation panel and QosmioPlayer Installing the batteries 1. Open the battery cover on the back side of the Remote Controller. Push the tab in the direction of the arrow (1) to open the cover (2). Battery cover Tab Opening the battery cover 2. Insert the batteries in place. Be sure to place the batteries with their polarities (+ and -) in the correct position. Batteries Inserting the batteries 3. Close the battery cover. Close the cover securely until it clicks.
Using the Remote Controller, Front operation panel and QosmioPlayer Replacing the batteries When the batteries in the Remote Controller reach the end of their life, the Remote Controller may not operate correctly or work only within a short distance from your computer. In this instance, you should purchase new batteries and replace the discharged ones. 1. Open the battery cover on the back side of the Remote Controller. 2. Replace the batteries.
Using the Remote Controller, Front operation panel and QosmioPlayer Switching video Input Follow the steps below to define the Monitor Input feature that allows video from a device such as an analog camera or game machine to be displayed on the LCD of your computer. This product supports several screen mode switching modes. When you select a mode that provides an aspect ratio different from that supported by software, for example TV mode, video may be displayed differently from the original.
Using the Remote Controller, Front operation panel and QosmioPlayer 2. Click the Monitor Input Settings button in the TOSHIBA Picture Enhancement Utility window. The Monitor Input Settings window appears. Figure 8-15 Monitor Input Settings window 3. Select the item for the Terminal Shape. ■ Select S-Video for the Terminal Shape if the device is connected to the S-Video in port. ■ Select Monitor-in for the Terminal Shape if the device is connected to the Monitor-in port. 4.
Using the Remote Controller, Front operation panel and QosmioPlayer Restrictions of the QosmioEngine The current mode will be maintained, and should be restored the next time the computer is switched on, and after the notebook returns from Standby Mode or Hibernation Mode. QosmioEngine is available only for the LCD and has the following restrictions. ■ QosmioEngine does not support LCD/CRT, CRT, TV, LCD/TV and Multi-Monitor. ■ Depending on the video being played, noise may be present.
Using the Remote Controller, Front operation panel and QosmioPlayer ■ Windows sounds are still heard even when the mode has been switched to Monitor-in. ■ Fn + F1/Fn + F5 hot keys are not available. ■ In Monitor-in mode, the screens of other applications will be invisible. This may cause you to operate an application incorrectly by pressing a mouse button or any key on the keyboard. To prevent operational errors, it is recommended to perform the following: ■ Close any applications running on your system.
Qosmio G20 Chapter 9 Optional Devices Optional devices can expand the computer’s capabilities and its versatility.
Optional Devices PC card The computer is equipped with a PC card slot that can accommodate one 5 mm Type II card. Any PC card that meets industry standards (manufactured by TOSHIBA or other vendor) can be installed. The slot supports 16-bit PC cards, including PC card 16’s multifunction card and CardBus PC cards. CardBus supports the new standard of 32-bit PC cards. The bus provides superior performance for the greater demands of multimedia data transmission.
Optional Devices Removing a PC card To remove the PC card, follow the steps below. 1. Open the Safely Remove Hardware icon on the Task Bar. 2. Point to PC card and click. 3. Press the PC card eject button to extend it. If the PC card is not inserted all the way, the eject button may not pop out. Be sure to push the PC card firmly and press the eject button again. 4. Press the PC card eject button to pop the PC card out slightly. 5. Grasp the PC card and draw it out.
Optional Devices To insert an ExpressCard, follow the steps below: 1. Insert an ExpressCard in the ExpressCard card slot. 2. Press gently to ensure a firm connection. ExpressCard slot ExpressCard Inserting the ExpressCard 3. After inserting the ExpressCard, refer to the ExpressCard’s documentation and check the configuration in Windows to make sure it is appropriate for your ExpressCard. Removing an ExpressCard To remove the ExpressCard, follow the steps below. 1.
Optional Devices Bridge media slot This slot lets you insert SD card, Memory Stick (Pro), xD picture card and MultiMediaCard. This Bridge media slot supports the following cards. ■ SD card ■ SDIO card ■ Memory Stick ■ Memory Stick PRO ■ xD picture card ■ MultiMediaCard Please note that not all cards have been tested and verified to work correctly. Therefore, it is not possible to guarantee that all cards will operate properly.
Optional Devices Inserting an SD card To insert an SD card, follow the steps below. 1. Insert an SD card in the Bridge media slot. 2. Press gently to ensure a firm connection. Bridge media indicator SD card Bridge media slot Inserting an SD card ■ Make sure the SD card is oriented properly before you insert it. ■ Do not turn the computer off or switch to Standby Mode or Hibernate Mode while files are being copied - doing so may cause data to be lost.
Optional Devices ■ Make sure the SD card indicator is out before you remove the SD card or turn off the computer’s power. If you remove the SD card or turn off the power while the computer is accessing the SD card you may lose data or damage the card. ■ Do not remove an SD card while the computer is in Standby or Hibernation mode. The computer could become unstable or data in the SD card could be lost. SD card care Set the write-protect switch to the lock position, if you do not want to record data. 1.
Optional Devices Inserting a Memory Stick To insert a Memory Stick, follow the steps below. 1. Insert the Memory Stick into the Bridge media slot. 2. Press gently to ensure a firm connection. Bridge media indicator Memory Stick Bridge media slot Inserting a Memory Stick Removing a Memory Stick To remove a Memory Stick, follow the steps below. 1. Open the Safely Remove Hardware icon on the Task Bar. 2. Point to Memory Stick and click. 3. Push in the card and release it to pop the card out slightly. 4.
Optional Devices 2. Press gently to ensure a firm connection. Bridge media indicator xD picture card Bridge media slot Inserting an xD picture card Removing an xD picture card To remove an xD picture card, follow the steps below. 1. Open the Safely Remove Hardware icon on the Task Bar. 2. Point to xD picture card and click. 3. Push in the card and release it to pop the card out slightly. 4. Grasp the card and remove it.
Optional Devices MultiMediaCard The computer is equipped with the Bridge media slot that can accommodate MultiMediaCard flash memory technology with various memory capacities. MultiMediaCards let you easily transfer data from devices, such as digital cameras and Personal Digital Assistants, that use MultiMediaCard flash-memory. The cards have a high level of security and copy protection features. Keep foreign objects out of the Bridge media slot A pin or similar object can damage the computer’s circuitry.
Optional Devices 4. Grasp the card and remove it. Bridge media indicator MultiMediaCard Bridge media slot Removing a MultiMediaCard ■ Make sure the indicator is out before you remove the MultiMediaCard or turn off the computer’s power. If you remove the MultiMediaCard or turn off the power while the computer is accessing the MultiMediaCard you may lose data or damage the card. ■ Do not remove a MultiMediaCard while the computer is in Standby or Hibernation mode.
Optional Devices Memory expansion You can install additional memory in the computer’s memory module socket to increase the amount of RAM. This section describes how to install and remove a memory module. ■ Place a mat beneath the computer to ensure that you do not scratch lid when replacing the memory module - you must ensure that this mat does not generate or hold a static electric charge. ■ When you install or remove a memory module, ensure that you do not touch any other internal areas of the computer.
Optional Devices Installing memory module There are slots for two memory modules, one over the other. The procedures are the same for installing either module. 1. Set the computer to boot mode and turn the computer’s power off. Make sure the Power indicator is off. Refer to the Turning off the power section in Chapter 3, Getting Started. 2. Remove AC adaptor and all cables connected to the computer. 3. Turn the computer upside down and remove the battery pack.
Optional Devices Align the grooves along the edges of the of the memory module with the locking tabs on the connector and insert the module into the connector firmly. If you find it difficult to install the memory module, gently prise the locking tabs outwards using the tip of your finger. Ensure that you hold the memory module along its left and right hand edges - the edges with the grooves in. ■ Be careful not to drop anything inside the computer.
Optional Devices 7. Grasp the module by the sides and pull it out. ■ If you use the computer for a long time, the memory modules and the circuits located close to the memory modules will become hot. In this case, let them cool to room temperature before you replace them. ■ Do not touch the connectors on the memory module or on the computer. Debris on the connectors may cause memory access problems. Latches Slot B Slot A Removing the memory module 8.
Optional Devices Battery charger The battery charger provides a convenient way to charge battery packs without requiring the use of your computer. The battery charger holds up to two lithium ion battery packs. Hard disk drive pack An extra hard disk drive expands the flexibility of your system and lets you carry your data without carrying the computer. Use a point size 0 Phillips screwdriver. Removing the Hard Disk Drive Pack To remove the hard disk drive pack, follow the steps below. 1.
Optional Devices 8. With the hard disk drive in a vertical position, lift it straight up and away from the connector. Plastic tab Hard Disk Drive Pack Removing the hard disk drive pack Installing the Hard Disk Drive Pack To install the hard disk drive pack, follow the steps below. 1. Move the connector until it is vertical. 2. Hold the hard disk drive vertically with its label on the left. 3. Connect the hard disk drive to the connector.
Optional Devices USB floppy disk drive The USB floppy disk drive module can be connected to the USB port. For details on connecting the USB floppy disk drive module, refer to Chapter 4, Operating Basics. External monitor An external analog monitor can be connected to the external monitor port on the computer. The computer supports VGA and Super VGA video modes. To connect a monitor, follow the steps below. 1. Turn the computer off. 2. Connect the monitor cable to the external monitor port.
Optional Devices Installation Connection via the S-Video out port 1. Plug one end of the S-Video out cable into the S-Video out port of your computer. S-Video out port Connecting the S-Video out port 2. Insert the other end of the S-Video out cable into the S1-/S2 video input of the TV set. You can then either use the computer’s speakers or a set of headphones connected to the headphone jack to get sound. Connection via the D-Video out port 1.
Optional Devices Settings for display video on TV To view video on the TV set, be sure to configure the following settings otherwise you may find that nothing is displayed. ■ Be sure to use the Fn +F5 HotKey to select the display device before starting to play video Do not change the display device while playing video. ■ Do not change the display device under the following conditions.
Optional Devices Monitor-in Set up Terminal Shape before you connect a device using the Monitor-in port. Refer to the section Switching video Input in Chapter 8, Using the Remote Controller, Front operation panel and QosmioPlayer for details. Models with TV Tuner The Monitor-in facility allows you to connect the following devices to display their video output on the built-in LCD.
Optional Devices 3. Insert the plugs at the other end of the output cable of the device you wish to use into the output terminals of that device. 4. Power on the device you wish to use (connected via the output cable). 5. Press the power button of your computer to turn it on. When you press the power button, Windows starts. If a music CD or DVD video disk is present in the drive, automatic play is activated. In that case, cancel it. 6. Press the computer’s Monitor-in button.
Optional Devices 2. Insert the corresponding plugs of the audio cable into the sound input terminals (red: sound, right channel, white: sound, left channel) of the Monitor-in cable. Sound left input (white) Sound right input (red) red white Connecting the cable 3. Insert the other end of the audio cable into the line out port of the audio device.
Optional Devices S-Video-in Set up Terminal Shape before you connect a device using the S-Video-in port. Refer to the section Switching video Input in Chapter 8, Using the Remote Controller, Front operation panel and QosmioPlayer for details. This port allows you to import video data from analog video cameras or video decks by connecting your computer to this type of device. Imported video can be edited or written to a DVD disk. 1.
Optional Devices i.LINK (IEEE1394) i.LINK (IEEE1394) is used for high-speed data transfer for a range of compatible devices such as ■ Digital video cameras ■ Hard disk drives ■ MO drives ■ CD-RW drives i.LINK uses a four-pin connector, which does not carry any electric current. External devices will need their own power supply to operate. Precautions ■ Make a back-up of your data before transferring it to the computer. There is a possibility that the original data will be damaged.
Optional Devices Connecting 1. Make sure the connectors are properly aligned and plug the i.LINK (IEEE1394) cable into the computer. i.LINK (IEEE1394) port i.LINK (IEEE1394) connector Connecting the i.LINK (IEEE1394) port 2. Plug the other end of the cable into the device. Note the following when you use i.LINK: ■ You may need to install drivers for your i.LINK devices. ■ Not all i.LINK devices have been tested. Therefore, compatibility with all i.LINK devices cannot be guaranteed.
Optional Devices Security lock Security locks enable you to anchor your computer a desk or other heavy object to help prevent unauthorized removal of the computer. Attach one end of a cable to a desk and the other end to the security lock slot on the back side of the computer. 1. Turn the computer so the back side faces you. 2. Align the holes for the security lock and attach the lock.
Optional Devices 9-28 User’s Manual
Qosmio G20 Chapter 10 Troubleshooting TOSHIBA designed the computer for durability. However, should problems occur, following the procedures in this chapter can help to determine the cause. All readers should become familiar with this chapter. Knowing what might go wrong can help prevent problems from occurring. Problem solving process Resolving problems will be much easier if you observe the following guidelines: ■ Stop immediately when you recognize a problem exists.
Troubleshooting Preliminary checklist Consider the simplest solution first. The items in this checklist are easy to fix and yet can cause what appears to be a serious problem. ■ Make sure you turn on all peripheral devices before you turn on the computer. This includes your printer and any other external device you are using. ■ Before you attach an external device, turn the computer off. When you turn the computer back on it recognizes the new device.
Troubleshooting Software Hardware The problems may be caused by your software or disk. If you cannot load a software package, the media may be damaged or the program might be corrupted. Try loading another copy of the software. If an error message appears while you are using a software package, check the software documentation. These documents usually include a problem solving section or a summary of error messages. Next, check any error messages in the operating system documentation.
Troubleshooting Self test When the computer starts up, the self test will be run automatically, and the following will be displayed: S This message remains on the screen for a few seconds. If the self test is successful, the computer tries to load the operating system, depending on how the Boot Priority is set in the TOSHIBA HW Setup program.
Troubleshooting AC power If you have trouble turning on the computer with the AC adaptor connected, check the DC IN indicator. Refer to Chapter 6, Power for more information. Problem Procedure AC adaptor doesn’t power the computer (DC IN indicator does not glow green) Check the connections. Make sure the cord is firmly connected to the computer and a power outlet. Check the condition of the cord and terminals. If the cord is frayed or damaged, replace it.
Troubleshooting Problem Procedure Unplug the AC adaptor and remove the battery to make sure the terminals are clean. If necessary wipe them with a soft dry cloth dipped in alcohol. Connect the AC adaptor and replace the battery. Make sure it is securely seated. Check the Battery indicator. If it does not glow, let the computer charge the battery for at least 20 minutes.
Troubleshooting Keyboard Keyboard problems can be caused by your setup configuration. For more information refer to Chapter 5, The Keyboard. Problem Procedure Some letter keys produce numbers Check that the numeric keypad overlay is not selected. Press Fn + F10 and try typing again. Output to screen is garbled Make sure the software you are using is not remapping the keyboard. Remapping involves reassigning the meaning of each key. See your software’s documentation.
Troubleshooting Hard disk drive Problem Procedure Computer does not boot from hard disk drive Check if a floppy disk is in the floppy disk drive or a CD-ROM is in the optical media drive. Remove any floppy disk and/or CD-ROM and check the Boot priority. Refer to the Boot Priority section in Chapter 7, HW Setup. There may be a problem with your operating system files. Refer to your operating system documentation. Slow performance Your files may be fragmented.
Troubleshooting Some CD/DVDs run The software or hardware configuration may be correctly, but others do causing a problem. Make sure the hardware not configuration matches your software’s needs. Check the CD/DVD's documentation. Check the type of CD/DVD you are using. The drive supports: DVD-ROM: DVD-ROM, DVD-Video CD-ROM: CD-DA, CD-Text, Photo CD (single/multi-session), CD-ROM Mode 1, Mode 2, CD-ROM XA Mode 2 (Form1, Form2), Enhanced CD (CD-EXTRA), Addressing Method 2 Check the region code on the DVD.
Troubleshooting ExpressCard Refer also to Chapter 9, Optional Devices. Problem Procedure ExpressCard error occurs Reseat the ExpressCard to make sure it is firmly connected. Make sure the connection between the external device and the card is firm. Cannot insert ExpressCard Please insert the card in the correct location. Refer to Chapter 9, Optional Devices for details. Check the card’s documentation. If problems persist, contact your dealer. SD card Refer also to Chapter 9, Optional Devices.
Troubleshooting xD picture card Refer also to Chapter 9, Optional Devices. Problem Procedure xD picture card error occurs Reseat the xD picture card to make sure it is firmly connected. Check the card’s documentation. You cannot read a file Make sure the target file is on the xD picture card inserted in the slot. If problems persist, contact your dealer. MultiMediaCard Refer also to Chapter 9, Optional Devices.
Troubleshooting Pointing device If you are using a USB mouse, also refer to the USB section in this chapter and to your mouse documentation. Touch Pad 10-12 Problem Procedure On-screen pointer does not respond to Pad operation The system might be busy. If the pointer is shaped as an hourglass, wait for it to return to its normal shape and try again to move it. Double-tapping does not work Try changing the double-click speed setting in the mouse control utility. 1.
Troubleshooting USB mouse Problem Procedure On-screen pointer does not respond to mouse operation The system might be busy. If the pointer is shaped as an hourglass, wait for it to resume its normal shape and try again to move it. Make sure the mouse is properly connected to the USB port. Double-clicking does not work Try changing the double-click speed setting in the mouse control utility. 1. Click start, click Control Panel, click Printers and Other Hardware and select Mouse icon. 2.
Troubleshooting Memory expansion Refer also to Chapter 9, Optional Devices, for information on installing memory modules. Problem Procedure Beeps sound in the pattern of one, three, three, one. Make sure the memory module installed in the expansion slot is compatible with the computer. If an incompatible module has been installed, follow the steps below. 1. Turn off the power. 2. Disconnect the AC adaptor and all peripheral devices. 3. Remove the battery pack. 4. Remove the memory module. 5.
Troubleshooting External monitor Refer also to Chapter 9, Optional Devices, and to your monitor’s documentation. Problem Procedure Monitor does not turn on Make sure that the external monitor’s power switch is on. Confirm that the external monitor’s power cable is plugged into a working power outlet. No display Try adjusting the contrast and brightness controls on the external monitor. Press hot keys Fn + F5 to change the display priority and make sure it is not set for the internal display.
Troubleshooting Problem Procedure Character display becomes garbled during a communication In data transmission, make sure the parity bit and stop bit settings correspond with those of the remote computer. Check the flow control and communication protocol. You cannot receive an incoming call Check the rings before auto answer setting in your communications application. You can also use the ATS0 command. If problems persist, contact your dealer.
Troubleshooting TV output signal Problem Procedure Display on TV is poor Make sure the TV type is correct for your area: NTSC (US, JAPAN), PAL (Europe). No display Try adjusting the contrast and brightness controls on the external monitor. Press hotkeys Fn + F5 to change the display. Refer to Chapter 5, The Keyboard. If problems persist, contact your dealer.
Troubleshooting TOSHIBA support If you require any additional help using your computer or if you are having problems operating the computer, you may need to contact TOSHIBA for additional technical assistance. Before you call Some problems you experience may be related to software or the operating system, it is important to investigate other sources of assistance first. Before contacting TOSHIBA, try the following: ■ Review troubleshooting sections in the documentation for software and peripheral devices.
Qosmio G20 Appendix A Specifications This appendix summarizes the computer’s technical specifications. Physical Dimensions Weight (typical) 4.45 kilograms, configured with: Pentium-M processor, 17” WXGA+, 1024MB+1024MB RAM, 100GB+100GB HDD, DVD Super Multi drive, TV Tuner, Wireless LAN (Intel b/g), Bluetooth. Size 406 (w) × 285 (d) × 43.1/48.
Specifications Built-in Modem Network control unit (NCU) Type of NCU AA Type of line Telephone line (analog only) Type of dialing Pulse Tone Control command AT commands EIA-578 commands Monitor function Computer’s speaker Communication specifications A-2 Communication system Data: Fax: Full duplex Half duplex Communication protocol Data ITU-T-Rec (Former CCITT) Bell Fax ITU-T-Rec (Former CCITT) V.21/V.22/V.22bis/V.32/ V.32bis/V.34/V.90 103/212A V.17/V.29/V.27ter/V.
Qosmio G20 Appendix B Display Controller and Modes Display controller The display controller interprets software commands into hardware commands that turn particular parts of the screen on or off. The display controller supports VGA, SVGA and XGA modes on the internal LCD display panel. A high-resolution external monitor connected to the computer can display up to 2048 horizontal and 1536 vertical pixels at 16 M colors.
Display Controller and Modes Table1 Video modes (VGA) B-2 Video mode Type Resolution Character matrix (pels) Colors Scanning frequency Vertical (Hz) 0, 1 VGA Text 40 × 25 Characters 8×8 16 of 256K 70 2, 3 VGA Text 80 × 25 Characters 8×8 16 of 256K 70 0*, 1* VGA Text 40 × 25 Characters 8 × 14 16 of 256K 70 2*, 3* VGA Text 80 × 25 Characters 8 × 14 16 of 256K 70 0+, 1+ VGA Text 40 × 25 Characters 9 × 16 16 of 256K 70 2+, 3+ VGA Text 80 × 25 Characters 9 × 16 16 of 25
Display Controller and Modes Table1 Video modes (VGA) continued Video mode Type Resolution Character matrix (pels) Colors Scanning frequency Vertical (Hz) D VGA Grph 320 × 200 Pels 8×8 16 of 256K 70 E VGA Grph 640 × 200 Pels 8×8 16 of 256K 70 F VGA Grph 640 × 350 Pels 8 × 14 Mono 70 10 VGA Grph 640 × 350 Pels 8 × 14 16 of 256K 70 11 VGA Grph 640 × 480 Pels 8 × 16 2 of 256K 60 12 VGA Grph 640 × 480 Pels 8 × 16 16 of 256K 60 13 VGA Grph 320 × 200 Pels 8×8 256 of
Display Controller and Modes Table 2 Video modes (SVGA) Vertical Frequency can be set up when outputting to External Monitor.
Display Controller and Modes Table 2 Video modes (SVGA) continued Resolution LCD colors CRT colors Vertical frequency (Hz) 640 × 480 64K/64K 64K/64K 60 75 85 100 800 × 600 64K/64K 64K/64K 60 75 85 100 1024 × 768 64K/64K 64K/64K 60 75 85 100 1280 × 1024 (Virtual)* 64K/64K 64K/64K 60 75 85 100 1440 × 900 64K/64K 64K/64K 60 75 85 100 1600 × 1200 (Virtual)* 64K/64K 64K/64K 60 75 85 100 1920 × 1440 (Virtual)* 64K/64K 64K/64K 60 75 85 2048 × 1536 (Virtual)* 64K/64K 64K/64K 60 7
Display Controller and Modes Table 2 Video modes (SVGA) continued Resolution LCD colors CRT colors Vertical frequency (Hz) 640 × 480 16M/16M 16M/16M 60 75 85 100 800 × 600 16M/16M 16M/16M 60 75 85 100 1024 × 768 16M/16M 16M/16M 60 75 85 100 1280 × 1024 (Virtual)* 16M/16M 16M/16M 60 75 85 100 1440 × 900 16M/16M 16M/16M 60 75 85 100 1600 × 1200 (Virtual)* 16M/16M 16M/16M 60 75 85 100 1920 × 1440 (Virtual)* 16M/16M 16M/16M 60 75 85 2048 × 1536 (Virtual)* 16M/16M 16M/16M 60 7
Display Controller and Modes PowerMizer PowerMizer is a graphics processor installed on this computer. The performance of PowerMizer can be configured in three ways. To define the performance, select the menu options shown below: Display Properties -> Settings -> Advanced -> GeForce Go 6600 -> GeForce Go 6600 -> nView Display Settings -> PowerMizer The graphics processor offers three options, Maximum Power Savings, Balanced and Maximum Performance, in each of the AC power mode and battery power mode.
Display Controller and Modes B-8 User’s Manual
Qosmio G20 Appendix C Wireless LAN This appendix is intended to help you get your Wireless LAN network up and running, with a minimum of parameters. Card Specifications Form Factor Mini PCI Type III Compatibility ■ IEEE 802.11 Standard for Wireless LANs ■ Wi-Fi (Wireless Fidelity) certified by the Wi-Fi Alliance. The ‘Wi-Fi CERTIFIED’ logo is a certification mark of the Wi-Fi Alliance.
Wireless LAN Radio Characteristics Radio Characteristics of Wireless LAN Cards may vary according to: ■ Country/region where the product was purchased ■ Type of product Wireless communication is often subject to local radio regulations. Although Wireless LAN wireless networking products have been designed for operation in the license-free 2.4GHz and 5GHz band, local radio regulations may impose a number of limitations to the use of wireless communication equipment.
Wireless LAN Supported Frequency Sub-bands Subject to the radio regulations that apply in the countries/regions, your Wireless LAN card may support a different set of 5 GHz/2.4 GHz channels. Consult your Wireless LAN administrator or your TOSHIBA Authorized dealer for information about the radio regulations that apply in the countries/regions. Wireless IEEE 802.11 Channels Sets (Revision B and G) User’s Manual Frequency Range Channel ID*2 2400-2483.
Wireless LAN Wireless IEEE 802.11 Channels Sets (Turbo Mode*3) Frequency Range Channel ID*2 2400-2483.5 MHz Note 6 2437 US only*4 When installing Wireless LAN cards, the channel configuration is managed as follows: ■ For wireless clients that operate in a Wireless LAN Infrastructure, the Wireless LAN card will automatically start operation at the channel identified by the Wireless LAN Access Point.
Wireless LAN 128 5640 132 5660 136 5680 140 5700 149 5745 153 5765 157 5785 161 5805 165 5825 Wireless Channels Sets (Turbo Mode*5) Frequency Range Channel ID 5150-5850 MHz Note 42 5210 US only *4 50 5250 US only *4 58 5290 US only *4 152 5760 US only *4 160 5800 US only *4 *1 Factory-set default channels *2 Consult your Wireless LAN administrator or your TOSHIBA Authorized dealer for the countries/regions in which these channels can be used.
Wireless LAN C-6 User’s Manual
Qosmio G20 Appendix D Bluetooth wireless technology Interoperability BluetoothTM Cards from TOSHIBA are designed to be interoperable with any product with Bluetooth wireless technology that is based on Frequency Hopping Spread Spectrum (FHSS) radio technology, and is compliant to: ■ Bluetooth Specification Ver.1.2, as defined and approved by The Bluetooth Special Interest Group. ■ Logo certification with Bluetooth wireless technology as defined by The Bluetooth Special interest Group.
Bluetooth wireless technology Interoperability ■ Bluetooth wireless technology is a new innovative technology, and TOSHIBA has not confirmed compatibility of its BluetoothTM products with all computers and/or equipment using Bluetooth wireless technology other than TOSHIBA portable computers. Always use BluetoothTM Cards from TOSHIBA in order to enable wireless networks over two or more (up to a total of seven) TOSHIBA portable computers using these cards.
Bluetooth wireless technology Interoperability Bluetooth wireless technology and your Health The products with Bluetooth wireless technology, like other radio devices, emit radio frequency electromagnetic energy. The level of energy emitted by devices with Bluetooth wireless technology however is far much less than the electromagnetic energy emitted by wireless devices like for example mobile phones.
Bluetooth wireless technology Interoperability Canada - Industry Canada (IC) This device complies with RSS 210 of Industry Canada. Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of this device.
Bluetooth wireless technology Interoperability (The model with embedded Wireless LAN module: PA3171U-1MPC) Relevant transmitters include FCC IDs: CJ6PA3171WL, CJ6UPA3232BT (The model with embedded Wireless LAN module: PA3272U-1MPC) Relevant transmitters include FCC IDs: CJ6UPA3272WLP, CJ6UPA3232BT (The model with embedded Wireless LAN module: PA3231U-1MPC) Relevant transmitters include FCC IDs: CJ6UPA3231WL, CJ6UPA3232BT (The model with embedded Wireless LAN module e: PA3233U-1MPC) Relevant transmitters in
Bluetooth wireless technology Interoperability Taiwan Article 14 Article 17 Unless approved, for any model accredited low power radio frequency electric machinery, any company, trader or user shall not change the frequency, increase the power or change the features and functions of the original design. Any use of low power radio frequency electric machinery shall not affect the aviation safety and interfere with legal communications.
Bluetooth wireless technology Interoperability 2. Indication The indication shown below appears on this equipment. (1) 2.4 : This equipment uses a frequency of 2.4 GHz. (2) FH : This equipment uses FH-SS modulation. (3) 1: The interference range of this equipment is less than 10 m. (4) This equipment uses a frequency bandwidth from 2,400 MHz to 2,483.5 MHz. It is impossible to avoid the band of mobile object identification systems. 3.
Bluetooth wireless technology Interoperability Approved Countries/Regions for use (Bluetooth™ wireless technology) BluetoothTM Card from TOSHIBA equipment is approved to the radio standard by the countries/regions in the following table. Do not use this equipment except in the countries/regions in the following table.
Qosmio G20 Appendix E TOSHIBA RAID TOSHIBA RAID (Redundant Array of Independent Disks) realizes high performance or fault tolerance, which are configured by arraying multiple independent hard disk drives. 2 hard disk drives can be used to construct a RAID configuration (RAID-1: mirroring or RAID-0: Striping).
TOSHIBA RAID Setting up Windows Manually Use the following procedures to set up your Windows operating system manually. Before Setting Up Windows Before setting up Windows, create a TOSHIBA RAID Driver Floppy Disk and configure the BIOS setup program. Creating the TOSHIBA RAID Driver Floppy Disk 1. Connect the USB floppy disk drive (optional) and insert a floppy disk. 2. Locate the TOSHIBA RAID Driver in the Tools & Drivers Depository on your hard disk drive (‘C:\TOOLSCD\RAID driver’ folder). 3.
TOSHIBA RAID ■ Boot menu When 2 hard disk drives are connected, it is possible to select which hard disk drive to boot from in the boot menu. However, if a RAID configuration is used, the 2 hard disk drives are recognized as 1 drive and there is no change in the boot configuration no matter which hard disk drive is selected. ■ When using a RAID-1 (mirroring) configuration, the additional hard disk drive’s capacity must be equal to or more than the capacity of the existing hard disk drive.
TOSHIBA RAID Starting, Modifying and Ending the BIOS Setup Program Starting the BIOS Setup Program 1. Switch on your computer while pressing the Esc key. If Password = is displayed, enter either the Supervisor Password, if one is set, or the User Password and press the Enter key. Please refer to Chapter 6, the TOSHIBA Password Utility, for details about the user password. The “Check system. Then press [F1] key.” message is displayed. 2. Press the F1 key. The BIOS setup program will start up.
3. The Execute Creation message is displayed once the configuration is modified. Move the cursor to the appropriate location and press the space bar to continue. Pressing the Home key will revert the modified Create State settings back to the Current State settings. 4. The following message will be displayed. Follow the instructions and press the keys in the following order: 1, 2, 3, 4, [Enter]. S Warning: If you change the RAID array, you will need to install the OS again.
E-6 User’s Manual
Qosmio G20 Appendix F AC Power Cord and Connectors The power cord’s AC input plug must be compatible with the various international AC power outlets and the cord must meet the standards for the country/region in which it is used. All cords must meet the following specifications: Length: Minimum 2 meters Wire size: Minimum 0.75 mm2 Current rating: Minimum 2.5 amperes Voltage rating: 125 or 250 VAC (depending on country/region’s power standards) Certification agencies U.S.
AC Power Cord and Connectors For the United States and Canada, two pin plug configuration must be a 2-15P (250V) or 1-15P (125V) and three pin plug configuration must be 6-15P (250V) or 5-15P (125V) as designated in the U.S. National Electrical code handbook and the Canadian Electrical Code Part II. The following illustrations show the plug shapes for the U.S.A. and Canada, the United Kingdom, Australia and Europe.
Qosmio G20 Appendix G Usage Restrictions This appendix describes the Usage Restrictions. ■ This configuration is designed to work with a signal from a conventional (standard or analog) TV antenna. ■ TOSHIBA does not guarantee that signals received by satellite or cable TV receivers will work properly and does not provide technical support for them. ■ The TOSHIBA Qosmio’s AC power adaptor must be connected to get the best possible audio and video performance.
Usage Restrictions G-2 User’s Manual
Qosmio G20 Appendix H If your computer is stolen Always take care of your computer and try to prevent it from being stolen. You are the owner of a valuable technical device, which may be highly attractive to thieves, so please do not leave it unattended in a public place. To further help protect against theft, security cables can be bought for use with your notebook when it is being used at home or in the office.
If your computer is stolen TOSHIBA Theft Registration Send to: TOSHIBA Europe GmbH Technical Service and Support Leibnizstr. 2 93055 Regensburg Germany Fax number: +49 (0) 941 7807 921 Country stolen: Machine type: (e.g. Satellite A50) Model number: (e.g. PSA50 YXT) Serial number: (e.g.
Qosmio G20 Glossary The terms in this glossary cover topics related to this manual. Alternate naming is included for reference.
Glossary FIR: fast infrared HDD: hard disk drive IDE: integrated drive electronics I/O: input/output IrDA: Infrared Data Association IRQ: interrupt request KB: kilobyte LCD: liquid crystal display LED: light emitting diode LSI: large scale integration MB: megabyte OCR: optical character recognition (reader) PCB: printed circuit board PCI: peripheral component interconnect RAM: random access memory RGB: red, green, and blue ROM: read only memory RTC: real time clock SCSI: small computer system interface SIO
Glossary analog signal: A signal whose characteristics such as amplitude and frequency vary in proportion to (are an analog of) the value to be transmitted. Voice communications are analog signals. ANSI: American National Standards Institute. An organization established to adopt and define standards for a variety of technical disciplines. For example, ANSI defined the ASCII standard and other information processing requirements. antistatic: A material used to prevent the buildup of static electricity.
Glossary bus: An interface for transmission of signals, data or electric power. byte: The representation of a single character. A sequence of eight bits treated as a single unit; also the smallest addressable unit within the system. C cache memory: High speed memory which stores data that increases processor speed and data transfer rate. When the CPU reads data from main memory, it stores a copy of this data in cache memory.
Glossary compatibility: 1) The ability of one computer to accept and process data in the same manner as another computer without modifying the data or the media upon which it is being transferred. 2) the ability of one device to connect to or communicate with another system or component. components: Elements or parts (of a system) which make up the whole (system). Composite Video (YUV): A standard video signal used to transmit images, e.g. from a VCR to a TV.
Glossary default: The parameter value automatically selected by the system when you or the program do not provide instructions. Also called a preset value. delete: To remove data from a disk or other data storage device. Synonymous with erase. device driver: A program that controls communication between a specific peripheral device and the computer. The CONFIG.SYS file contains device drivers that MS-DOS loads when you turn the computer on.
Glossary E echo: To send back a reflection of the transmitted data to the sending device. You can display the information on the screen, or output it to the printer, or both. When a computer receives back data it transmitted to a CRT (or other peripheral device) and then retransmits the data to printer, the printer is said to echo the CRT. erase: See delete. escape: 1) A code (ASCII code 27), signaling the computer that what follows are commands; used with peripheral devices such as printers and modems.
Glossary H hard disk: A non-removable disk usually referred to as drive C. The factory installs this disk and only a trained engineer can remove it for servicing. Also called fixed disk. hard disk drive (HDD): An electromechanical device that reads and writes a hard disk. See also hard disk. hardware: The physical electronic and mechanical components of a computer system: typically, the computer itself, external disk drives, etc. See also software and firmware.
Glossary IrDA 1.1: An industry standard that enables cableless infrared serial data transfer at speeds of up to 4 Mbps. J jumper: A small clip or wire that allows you to change the hardware characteristics by electrically connecting two points of a circuit. K K: Taken from the Greek word kilo, meaning 1000; often used as equivalent to 1024, or 2 raised to the 10th power. See also byte and kilobyte. KB: See kilobyte.
Glossary microprocessor: A hardware component contained in a single integrated circuit that carries out instructions. Also called the central processing unit (CPU), one of the main parts of the computer. mode: A method of operation, for example, the boot mode, standby mode or the hibernation mode. modem: Derived from modulator/demodulator, a device that converts (modulates) digital data for transmission over telephone lines and then converts modulated data (demodulates) to digital format where received.
Glossary P PAL: PAL (Phase Alternating Line) is the dominant video and broadcasting standard in Europe. parity: 1) The symmetrical relationship between two parameter values (integers) both of which are either on or off; odd or even; 0 or 1. 2) In serial communications, an error detection bit that is added to a group of data bits making the sum of the bits even or odd. Parity can be set to none, odd, or even. password: A unique string of characters used to identify a specific user.
Glossary R Radio frequency interference (RFI) shield: A metal shield enclosing the printed circuit boards of the printer or computer to prevent radio and TV interference. All computer equipment generates radio frequency signals. The FCC regulates the amount of signals a computing device can allow past its shielding. A Class A device is sufficient for office use. Class B provides a more stringent classification for home equipment use.
Glossary software: The set of programs, procedures and related documentation associated with a computer system. Specifically refers to computer programs that direct and control the computer system’s activities. See also hardware. stop bit: One or more bits of a byte that follow the transmitted character or group codes in asynchronous serial communications. subpixel: Three elements, one red, one green and blue (RGB), that make up a pixel on the color LCD.
Glossary W warm start: Restarting or resetting a computer without turning it off. window: A portion of the screen that can display its own application, document or dialog box. Often used to mean a Microsoft Windows window. Wireless LAN: Local Area Network (LAN) through wireless communication. write protection: A method for protecting a floppy disk from accidental erasure.
Qosmio G20 Index A AC adaptor 1-4 additional 1-16, 9-15 connecting 3-4 DC IN 15V jack 2-4 ASCII characters 5-9 B Battery charging 6-8 extending battery life 6-11 indicator 2-11, 6-3 location 2-7 Monitoring capacity 6-9 real time clock 1-4, 6-5 safety precautions 6-5 save mode 1-10, 1-11 types 6-4 Battery charger 1-16, 9-16 Battery pack 1-4, 2-7 additional 9-15 replacing 6-11 Bluetooth 1-9 problems 10-16 TOSHIBA Stack 1-14 Bridge media slot 1-6, 9-5 C Cache memory 1-4 Cleaning the computer 4-25 Cooling ve
Index F Fn + 3 (QosmioEngine) 5-7 Fn + 4 (Monitor-in) 5-7 Fn + Ctrl (enhanced keyboard’s simulation) 5-3 Fn + Enter 5-3 Fn + Esc (sound mute) 5-3 Fn + F1 (instant security) 5-4 Fn + F10 (Arrow mode) 5-3 Fn + F11 (Numeric mode) 5-3 Fn + F12 (ScrLock) 5-3 Fn + F2 (power save mode) 5-4 Fn + F3 (standby) 5-4 Fn + F4 (hibernation) 5-4 Fn + F5 (display selection) 5-5 Fn + F6 (Internal LCD screen Brightness decreases) 5-5 Fn + F7 (Internal LCD screen Brightness increases) 5-5 Fn + F8 (wireless setting) 5-6 Fn + F
Index temporarily using overlay (overlay off) 5-9 turning on the overlays 5-8 L LAN 1-8, 4-24 active indicator 2-5 cable types 4-24 connecting 4-24 disconnecting 4-25 Link indicator 2-5 problems 10-16 M Media care 4-17 CD/DVDs 4-17 floppy disks 4-17 SD card 9-7 Memory 1-4 expansion 1-16, 9-12 installing 9-13 problems 10-14 removing 9-14 Memory Stick/Memory Stick Pro 9-7 inserting 9-8 location of slot 2-3 problems 10-10 removing 9-8 Modem 1-8, 4-18 connecting 4-20 disconnecting 4-20 jack 2-2 properties m
Index MultiMediaCard 10-11 Overheating power down 10-4 Password 10-6 PC card 10-9 Pointing device 10-12 Power 10-4 Real Time Clock 10-6 SD card 10-10 Self test 10-4 Sound system 10-14 Support from TOSHIBA 10-18 System start-up 10-3 TV output signal 10-17 USB 10-13 USB floppy disk drive 10-9 Wireless LAN 10-16 xD picture card 10-11 Processor 1-4 Q QosmioEngine 5-7, 8-28 R RecordNow! 1-14, 4-12 Remote control receiver 8-20 Remote Controller 8-20 Restarting the computer 3-11 S SD card 9-5 care 9-7 format
