User’s Manual PORTÉGÉ R600/PORTÉGÉ A600
Table of Contents Copyright. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . vi Disclaimer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . vi Trademarks . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . vi FCC information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . vii EU Conformity Statement . . . . . . . . . . . . . . . . . .
PORTÉGÉ R600/PORTÉGÉ A600 Chapter 2 The Grand Tour Front with the display closed . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-1 Left side . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-2 Right side . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-4 Back . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-7 Underside . . . . . . . . . .
PORTÉGÉ R600/PORTÉGÉ A600 Chapter 6 Power and Power-Up Modes Power conditions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-1 Monitoring of power condition . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-3 Battery . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-4 TOSHIBA Password Utility. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-11 Power-up modes. . . . . . . . . . . . . . . .
PORTÉGÉ R600/PORTÉGÉ A600 Graphics Processor Unit ("GPU")*7 . . . . . . . . . . . . . . . . . . . . . . . . . . Wireless LAN*8 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . USB Sleep and Charge*9 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Copy Protection*10 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
PORTÉGÉ R600/PORTÉGÉ A600 Copyright © 2008 by TOSHIBA Corporation. All rights reserved. Under the copyright laws, this manual cannot be reproduced in any form without the prior written permission of TOSHIBA. No patent liability is assumed, with respect to the use of the information contained herein.
PORTÉGÉ R600/PORTÉGÉ A600 FCC information FCC notice "Declaration of Conformity Information" This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
PORTÉGÉ R600/PORTÉGÉ A600 EU Conformity Statement This product and - if applicable - the supplied accessories too are marked with "CE" and comply therefore with the applicable harmonized European standards listed under the Low Voltage Directive 2006/95/EC, the EMC Directive 2004/108/EC and/or R&TTE Directive 1999/5/EC. Responsible for CEmarking: Manufacturer: TOSHIBA EUROPE GMBH, Hammfelddamm 8, 41460 Neuss, Germany.
PORTÉGÉ R600/PORTÉGÉ A600 Network Compatibility Statement This product is designed to work with, and is compatible with the following networks. It has been tested to and found to conform with the additional requirements conditional in EG 201 121.
PORTÉGÉ R600/PORTÉGÉ A600 This label is located on the module.
PORTÉGÉ R600/PORTÉGÉ A600 Telephone company procedures The goal of the telephone company is to provide you with the best service it can. In order to do this, it may occasionally be necessary for them to make changes in their equipment, operations, or procedures. If these changes might affect your service or the operation of your equipment, the telephone company will give you notice in writing to allow you to make any changes necessary to maintain uninterrupted service.
PORTÉGÉ R600/PORTÉGÉ A600 Instructions for IC CS-03 certified equipment 1. The Industry Canada label identifies certified equipment. This certification means that the equipment meets certain telecommunications network protective, operational and safety requirements as prescribed in the appropriate Terminal Equipment Technical Requirements document(s). The Department does not guarantee the equipment will operate to the user’s satisfaction.
PORTÉGÉ R600/PORTÉGÉ A600 Notes for Users in Australia and New Zealand Modem warning notice for Australia Modems connected to the Australian telecoms network must have a valid Austel permit. This modem has been designed to specifically configure to ensure compliance with Austel standards when the country/region selection is set to Australia. The use of other country/region setting while the modem is attached to the Australian PSTN would result in you modem being operated in a non-compliant manner.
PORTÉGÉ R600/PORTÉGÉ A600 ■ Some parameters required for compliance with Telecom’s PTC Specifications are dependent on the equipment (PC) associated with this modem.
PORTÉGÉ R600/PORTÉGÉ A600 ■ It is recommended that this equipment be disconnected from the Telecom line during electrical storms. ■ When relocating the equipment, always disconnect the Telecom line connection before the power connection, and reconnect the power first. ■ This equipment may not be compatible with Telecom Distinctive Alert cadences and services such as FaxAbility.
PORTÉGÉ R600/PORTÉGÉ A600 Disposal of batteries and/or accumulators The crossed out wheeled dust bin symbol indicates that batteries and/or accumulators must be collected and disposed of separately from household waste.
PORTÉGÉ R600/PORTÉGÉ A600 Optical disc drive safety instructions Be sure to check the international precautions at the end of this section. Panasonic Communications DVD Super Multi UJ-844 ■ The DVD Super Multi drive model employs a laser system. To ensure proper use of this product, please read this instruction manual carefully and retain for future reference. Should the unit ever require maintenance, contact an authorized service location.
PORTÉGÉ R600/PORTÉGÉ A600 When DVD-R DL or DVD+R DL format disc is read with this drive, the disc is available only to read.
PORTÉGÉ R600/PORTÉGÉ A600 Panasonic Communications DVD Super Multi with Double Layer Recording UJ862 ■ The DVD Super Multi drive model employs a laser system. To ensure proper use of this product, please read this instruction manual carefully and retain for future reference. Should the unit ever require maintenance, contact an authorized service location. ■ Use of controls, adjustments or the performance of procedures other than those specified may result in hazardous radiation exposure.
PORTÉGÉ R600/PORTÉGÉ A600 International precautions CAUTION: This appliance contains a laser system and is classified as a “CLASS 1 LASER PRODUCT.” To use this model properly, read the instruction manual carefully and keep this manual for your future reference. In case of any trouble with this model, please contact your nearest “AUTHORIZED service station.” To prevent direct exposure to the laser beam, do not try to open the enclosure.
PORTÉGÉ R600/PORTÉGÉ A600 OBS! Apparaten innehåller laserkomponent som avger laserstråining överstigande gränsen för laserklass 1. VAROITUS. Suojakoteloa si saa avata. Laite sisältää laserdiodin, joka lähetää näkymätöntä silmilie vaarallista lasersäteilyä. CAUTION: USE OF CONTROLS OR ADJUSTMENTS OR PERFORMANCE OF PROCEDURES OTHER THAN THOSE SPECIFIED IN THE OWNER’S MANUAL MAY RESULT IN HAZARDOUS RADIATION EXPOSURE.
Preface Congratulations on your purchase of the PORTÉGÉ R600/PORTÉGÉ A600 series computer. This powerful notebook computer provides excellent expansion capability, includes multimedia functionality, and is designed to provide years of reliable, high-performance computing. This manual tells how to set up and begin using your PORTÉGÉ R600/PORTÉGÉ A600 computer. It also provides detailed information on configuring your computer, basic operations and care, using optional devices and troubleshooting.
PORTÉGÉ R600/PORTÉGÉ A600 Icons Icons identify ports, dials, and other parts of your computer. The indicator panel also uses icons to identify the components it is providing information on. Keys The keyboard keys are used in the text to describe many computer operations. A distinctive typeface identifies the key top symbols as they appear on the keyboard. For example, ENTER identifies the ENTER key. Key operation Some operations require you to simultaneously use two or more keys.
PORTÉGÉ R600/PORTÉGÉ A600 Terminology This term is defined in this document as follows: User’s Manual Start The word "Start" refers to the " Microsoft® Windows Vista®. " button in HDD or Hard disk drive Some models are equipped with a "Solid State Drive (SSD)" instead of a hard disk drive. In this manual, the word "HDD" or "Hard disk drive" also refers to the SSD unless otherwise stated.
General Precautions TOSHIBA computers are designed to optimize safety, minimize strain and withstand the rigors of portability. However, certain precautions should be observed to further reduce the risk of personal injury or damage to the computer. Be certain to read the general precautions below and to note the cautions included in the text of the manual.
PORTÉGÉ R600/PORTÉGÉ A600 Creating a computer-friendly environment Place the computer on a flat surface that is large enough for the computer and any other items you are using, such as a printer. Leave enough space around the computer and other equipment to provide adequate ventilation. Otherwise, they may overheat. To keep your computer in prime operating condition, protect your work area from: ■ Dust, moisture, and direct sunlight.
PORTÉGÉ R600/PORTÉGÉ A600 Pressure or impact damage Do not apply heavy pressure to the computer or subject it to any form of strong impact as this can damage the computer's components or otherwise cause it to malfunction. Mobile phones Please be aware that the use of mobile phones can interfere with the audio system. The operation of the computer will not be impaired in any way, but it is recommended that a minimum distance of 30cm is maintained between the computer and a mobile phone that is in use.
Chapter 1 Getting Started This chapter provides an equipment checklist, and basic information to start using your computer. Some of the features described in this manual may not function properly if you use an operating system that was not pre-installed by TOSHIBA. Equipment checklist Carefully unpack your computer, taking care to save the box and packaging materials for future use.
Getting Started Software The following Windows® operating system and utility software are preinstalled.
Getting Started Getting Started ■ All users should be sure to read the section Starting up for the first time. ■ Be sure to read the enclosed Instruction Manual for Safety and Comfort for information on the safe and proper use of this computer. It is intended to help you be more comfortable and productive while using a notebook computer. By following the recommendations in it you may reduce your chance of developing a painful or disabling injury to your hand, arms, shoulders or neck.
Getting Started Connecting the AC adaptor Attach the AC adaptor when you need to charge the battery or you want to operate from AC power. It is also the fastest way to get started, because the battery pack will need to be charged before you can operate from battery power. The AC adaptor can be connected to any power source supplying from 100 to 240 volts and 50 or 60 hertz. For details on using the AC adaptor to charge the battery pack, refer to Chapter 6, Power and Power-Up Modes.
Getting Started 1. Connect the power cord to the AC adaptor. Figure 1-1 Connecting the power cord to the AC adaptor (2-pin plug) Figure 1-2 Connecting the power cord to the AC adaptor (3-pin plug) Either a 2-pin or 3-pin adaptor/cord will be included with the computer depending on the model. 2. Connect the AC adaptor’s DC output plug to the DC IN 15V jack on the left side of the computer. DC IN 15V jack DC output plug Figure 1-3 Connecting the DC output plug to the computer (PORTÉGÉ R600) 3.
Getting Started Opening the display The display panel can be opened to a wide range of angles for optimal viewing. While holding down the palm rest with one hand so that the main body of the computer is not raised, slowly lift the display panel - this will allow the angle of the display panel to be adjusted to provide optimum clarity. Display panel Figure 1-4 Opening the display panel (PORTÉGÉ R600) Use reasonable care when opening and closing the display panel.
Getting Started Turning on the power This section describes how to turn on the power - the Power indicator will then indicate the status. Please refer to the Monitoring of power condition section in Chapter 6, Power and Power-Up Modes for more information. ■ After you turn on the power for the first time, do not turn it off until you have set up the operating system. Please refer to the section Starting up for the first time for more information. ■ Volume cannot be adjusted during Windows Setup. 1.
Getting Started ■ Make sure the Hard Disk Drive or Hard Disk Drive/Optical Disc Drive indicator is off. If you turn off the power while a disk (disc) is being accessed, you may lose data or damage the disk. ■ Never turn off the power while an application is running. Doing so could cause loss of data. ■ Never turn off the power, disconnect an external storage device or remove storage media during data read/write. Doing so can cause data loss. 3. Click Start. 4.
Getting Started ■ When the AC adaptor is connected, the computer will go into Sleep Mode according to the settings in the Power Options (to access it, Start -> Control Panel -> System and Maintenance -> Power Options). ■ To restore the operation of the computer from Sleep Mode, press and hold the power button or any key on the keyboard for a short amount of time. Please note that keyboard keys can only be used if the Wake-up on Keyboard option is enabled within the HW Setup utility.
Getting Started ■ When the computer is in Sleep Mode, the Power indicator will blink orange. ■ If you are operating the computer on battery power, you can lengthen the overall operating time by turning it off into Hibernation Mode - Sleep Mode will consume more power while the computer is off. Sleep Mode limitations Sleep Mode will not function under the following conditions: ■ Power is turned back on immediately after shutting down. ■ Memory circuits are exposed to static electricity or electrical noise.
Getting Started Starting Hibernation Mode You can also enable Hibernation Mode by pressing FN + F4 - please refer to Chapter 5, The Keyboard, for further details. To enter Hibernation Mode, follow the steps below. 1. Click Start. 2. Click the arrow button ( ( ) in the power management buttons ) and select Hibernate from the menu. Automatic Hibernation Mode The computer can be configured to enter Hibernation Mode automatically when you press the power button or close the lid.
Getting Started Restarting the computer Certain conditions require that you reset the computer, for example if: ■ You change certain computer settings. ■ An error occurs and the computer does not respond to your keyboard commands. If you need to restart the computer, there are three ways this can be achieved: ■ Click Start then click the arrow button ( buttons ( ) in the power management ) and select Restart from the menu.
Getting Started System Recovery This section describes the creation of Recovery Discs and their use. Creating Optical Recovery Discs This section describes how to create Recovery Discs. ■ For models that do not provide with optical disc drives, an external optical disc drive is required to create the Recovery Discs. A writable external optical disc drive that is sold separately and compatible to the computer is required to create the Recovery Discs. It can be purchased from TOSHIBA dealers.
Getting Started Please note that some of the above media may not be compatible with the optical disc drive installed into your computer. You should therefore verify the optical disc drive supports the blank media you have chosen before proceeding. 3. Turn on your computer and allow it to load the Windows Vista operating system from the hard disk drive as normal. 4. Insert the first blank media into the optical disc drive tray. 5.
Getting Started Restoring the pre-installed software from your created Recovery Discs A recovery CD, created according to the Creating Optical Recovery Discs section in this chapter, is required to restore the software. In order to create a recovery CD, an external optical disc drive is required for models which are not equipped with an internal optical disc drive. It can be purchased from TOSHIBA dealers.
Chapter 2 The Grand Tour This chapter identifies the various components of the computer - it is recommended that you become familiar with each before you operate the computer. Legal Footnote (Non-applicable Icons)*1 For more information regarding Non-applicable Icons, please refer to the Legal Footnotes section in Appendix H or click the *1 above. Please handle your computer carefully to avoid scratching or damaging the surface.
The Grand Tour System indicators These LED indicators allow you to monitor the status of various computer functions and are described in more detail within the System indicators section. Left side The following figure shows the computer’s left side. External monitor port DC IN 15V jack Cooling vents eSATA/USB combo port Universal Serial Bus (USB 2.
The Grand Tour eSATA/USB combo port One eSATA/USB combo port, which complies to the USB 2.0 standard, is provided on the left hand side of the computer. The ports with the icon ( ) has USB Sleep and Charge. This port has eSATA (External Serial ATA) function. Keep foreign metal objects, such as screws, staples and paper clips, out of the eSATA/USB combo port. Foreign metal objects can create a short circuit, which can cause damage and fire, possibly resulting in serious injury.
The Grand Tour Headphone jack A 3.5 mm mini headphone jack enables connection of stereo headphones. Volume control dial Use this dial to adjust the volume of the internal monaural speaker and optional external stereo headphones (if connected). Move the Volume control dial to the right to decrease the volume and to the left to increase the volume. Right side The following figure shows the computer’s right side. SD Card slot ExpressCard slot Wireless communication switch Universal Serial Bus (USB 2.
The Grand Tour SD Card slot This slot can accommodate a single SD/SDHC memory card in order to transfer data from devices, such as digital cameras, onto your computer. Keep foreign metal objects, such as screws, staples and paper clips, out of the SD Card slot. Foreign metal objects can create a short circuit, which can cause damage and fire, possibly resulting in serious injury. Modem jack The modem jack lets you use a modular cable to connect the modem directly to a telephone line.
The Grand Tour Wireless communication switch Slide this switch to the left to turn off Wireless LAN, Bluetooth™ and Wireless WAN functions. Slide it to the right to turn on the functions. Only some models are equipped with Bluetooth, Wireless LAN and Wireless WAN functions. ■ Do not use the Wireless LAN (Wi-Fi®) or Bluetooth functionalities near a microwave oven or in areas subject to radio interference or magnetic fields.
The Grand Tour Back The following figure shows the computer’s back. Battery pack Figure 2-8 The back of the computer (PORTÉGÉ R600) Battery pack Figure 2-9 The back of the computer (PORTÉGÉ A600) Battery pack User’s Manual The battery pack provides power to the computer when the AC adaptor is not connected. For more detailed information on the use and operation of the battery pack please refer to Chapter 6, Power and Power-Up Modes.
The Grand Tour Underside The following figure shows the underside of the computer. You should ensure that the display is closed before the computer is turned over to avoid causing any damage.
The Grand Tour Notches Notches on the computer engage hooks on the TOSHIBA Slim Port Replicator II to ensure a secure connection. Docking port This port enables connection of an optional TOSHIBA Slim Port Replicator II described in Chapter 3, Hardware, Utilities and Options. ■ Only the TOSHIBA Slim Port Replicator II can be used with this computer. Do not attempt to use any other Port Replicator. ■ Keep foreign objects out of the docking port.
The Grand Tour Front with the display open This section shows the computer with the display panel open. In order to open the display, lift the display panel up and position it at a comfortable viewing angle for you.
The Grand Tour Bluetooth antenna, Wireless LAN antennas, Wireless WAN antennas (Not shown) Web Camera LED Web Camera LCD Sensor switch (Not shown) Display screen Display hinge TOSHIBA Assist button TOSHIBA Presentation button Fingerprint Sensor Display hinge Speaker Touch Pad control buttons Power button Keyboard Touch Pad Microphone Figure 2-13 The front of the computer with the display panel open (PORTÉGÉ A600) User’s Manual Display hinges The display hinges allow the display panel to be posit
The Grand Tour User’s Manual Web Camera Web Camera is a device that allows you to record video or take photographs with your computer. You can use it for video chatting or video conferences using a communication tool such as Windows Live Messenger. Camera Assistant Software will help you to add various video effects to your video or photograph. Enables the transmission of video and use of video chat via the internet using specialized applications. The effective pixel count for this web camera is 0.
The Grand Tour Back light On/Off button Press this button to turn on or off the back light of the display screen. If you turn off the back light outdoors in a good weather, you can use the computer for a longer period. Some models are equipped with a Back light On/Off button. TOSHIBA Presentation button The TOSHIBA Presentation button has the same functionality as the Connect display button in the Mobility Center.
The Grand Tour Indicators This section explains indicator functions. System indicators The LED system indicators for specific computer operations glow when those operations are in progress. Figure 2-14 System indicators User’s Manual DC IN The DC IN indicator normally glows white or green when power is being correctly supplied from the AC power adaptor. However, If the output voltage from the adaptor is abnormal, or if the computer's power supply malfunctions, this indicator will flash orange.
The Grand Tour Wireless communication The Wireless communication indicator glows orange when the Bluetooth and Wireless LAN functions are turned on. Only some models are equipped with Bluetooth and Wireless LAN functions. Wireless WAN The Wireless WAN indicator glows or blinks blue when the Wireless WAN function is on. The indicator will glow or blink in order to indicate the connection status of the Wireless WAN function. A Wireless WAN module must be installed to use this function.
The Grand Tour CAPS LOCK This indicator glows green when letter keys are locked into their uppercase format. Arrow Mode When the Arrow Mode indicator lights green, you can use the gray labeled keys on the keypad overlay as cursor keys. Please refer to the Keypad overlay section in Chapter 5, The Keyboard for more information. Numeric Mode When the Numeric Mode indicator lights green, you can use the gray labeled keys on the keypad overlay for number entry.
The Grand Tour Writable discs This section describes the types of writable CD/DVD discs. Check the specifications of your drive to see the types of discs it can write. Use TOSHIBA Disc Creator to write compact discs. Refer to Chapter 4, Operating Basics. CDs ■ CD-R discs can be written only once. The recorded data cannot be erased or changed. ■ CD-RW discs including multi speed CD-RW discs, high-speed CD-RW discs and ultra-speed CD-RW discs can be recorded more than once.
The Grand Tour DVD Super Multi drive The full-size DVD Super Multi drive module lets you record data to rewritable CD/DVDs as well as run either 12 cm (4.72") or 8cm (3.15") CD/DVDs without using an adaptor. ■ When DVD-R DL or DVD+R DL format disc is read with this drive, the disc is available only to read. ■ The read speed is slower at the center of a disc and faster at the outer edge.
The Grand Tour AC adaptor The AC adaptor can automatically adjust to any voltage ranging from 100 to 240 volts and to a frequency of either 50 or 60 hertz, enabling you to use this computer in almost all country/region. The adaptor converts AC power to DC power and reduces the voltage supplied to this computer. To recharge the battery, simply connect the AC adaptor to a power source and to the computer. Please refer to Chapter 6, Power and Power-Up Modes for further information.
Chapter 3 Hardware, Utilities and Options Hardware This section describes the hardware of your computer. The actual specifications may vary depending on the model you purchased. Processor CPU The computer is equipped with an Intel® processor. Intel® CoreTM 2 Duo Processor, which incorporates a 3MB level2 cache memory and also supports Enhanced Intel SpeedStep® Technology.
Hardware, Utilities and Options Memory Built-in 1,024MB memory module is installed on the main board. Slot 512, 1,024, 2,048 or 4,096MB memory module can be installed in the computer's memory slot for a maximum of 5,120MB system memory. This computer can be equipped with memory modules of a maximum size of 5,120MB. The actual amount of useable system memory will be less than the installed memory modules.
Hardware, Utilities and Options RTC battery The internal RTC battery backs up the Real Time Clock (RTC) and calendar. AC adaptor The AC adaptor provides power to the system and recharges the batteries when they are low. It comes with a detachable power cord which will either have a 2-pin or 3-pin plug enclosure. As the AC adaptor is universal, it can receive a range of AC voltages from 100 to 240 volts, however you should note that the output current varies among different models.
Hardware, Utilities and Options Legal Footnote (Hard Disk Drive (HDD) Capacity)*5 For more information regarding Hard Disk Drive (HDD) Capacity, please refer to the Legal Footnotes section in Appendix H or click the *5 above. Optical disc drive Drive The following optical disc drive is pre-installed in this computer. ■ DVD Super Multi drive ■ DVD Super Multi drive Double Layer Some models are equipped with an optical disc drive. 2.6GB and 5.2GB DVD-RAM media cannot be read from or written to.
Hardware, Utilities and Options Sound Sound system The integrated sound system provides support for the computer's internal speaker and microphone, as allowing an external microphone and headphones to be connected via the appropriate jacks. Multimedia Web Camera Web Camera is a device that allows you to record video or take photographs with your computer. You can use it for video chatting or video conferences using a communication tool such as Windows Live Messenger.
Hardware, Utilities and Options Bluetooth Some computers in this series have Bluetooth wireless communication function which eliminates the need for cables between electronic devices such as computers, printers and mobile phones. When it is enabled, Bluetooth provides the wireless personal area network environment which is safe and trustworthy, that is quick and easy.
Hardware, Utilities and Options User’s Manual TOSHIBA Presentation button The TOSHIBA Presentation button has the same functionality as the Connect display button in the Mobility Center. Pressing this button when an external display is connected will open the Windows Vista TMM (Transient Multimon Manager) screen. Some models are equipped with a TOSHIBA Presentation button.
Hardware, Utilities and Options Battery save mode *1 This feature lets you configure the computer in order to save battery power. This can be specified in the Power Options. Panel power on/off *1 This feature automatically turns power to the computer off when the display panel is closed, and turns it back on when the display panel is opened. This can be specified in the Power Options.
Hardware, Utilities and Options Hibernation Mode This feature lets you turn off the power to the computer without exiting from your software. The contents of main memory are automatically saved to the hard disk drive so that when you next turn the power on again, you can continue working right where you left off. Refer to the Turning off the power section in Chapter 1, Getting Started, for more details.
Hardware, Utilities and Options USB Wakeup function This function restores the computer from Sleep Mode depending on the external devices connected to the USB ports. For example, if a mouse or USB keyboard is connected to a USB port, moving the mouse/keyboard will wakeup the computer. The "USB Wakeup function" operates under Windows Vista operating system and it works for all USB ports.
Hardware, Utilities and Options User’s Manual TOSHIBA PC Diagnostic Tool The TOSHIBA PC Diagnostic Tool will display basic system configuration information and allow the functionality of some of the computer's builtin hardware devices to be tested. TOSHIBA Password Utility The TOSHIBA Password utility allows you to set a password in order to restrict access to the computer. TOSHIBA Flash Cards The TOSHIBA Flash Cards provide a quick way to modify selected system functions and to launch applications.
Hardware, Utilities and Options Utilities and Applications This section describes the pre-installed utilities that come with the computer and details how to start them. For further information on their operation, please refer to each utility's online manual, help files or README.TXT file.
Hardware, Utilities and Options ■ Frame dropping, audio skipping or out of synch audio and video may occur during playback of some DVD Video titles. ■ Make sure to connect the computer's AC adaptor when playing a DVD Video. Power-saving features may interfere with smooth playback. Bluetooth Stack for Windows by Toshiba This software enables communication between the computer and external Bluetooth devices such as printers and mobile phones.
Hardware, Utilities and Options User’s Manual TOSHIBA Disc Creator You can create CD's and DVD's in a number of formats including audio CD's that can be played on a standard CD player, and data CD's/DVD's which can store copies of the files and folders on your computer's hard disk drive. This software can be used on models with a DVD Super Multi drive. To start this utility, click Start -> All Programs -> TOSHIBA -> CD&DVD Applications -> Disc Creator.
Hardware, Utilities and Options Trusted Platform Module (TPM) The TPM (Trusted Platform Module) is a security encryption device for the hard disk drive. BIOS setup and Infineon TPMSoftware Professional Package must be configured in order to use TPM. For further information on how to set up and use this utility, please refer to the Infineon TPM Installation Guide from the C:\TOSAPINS\Infineon TPM Installation Guide. To enable TPM through the BIOS setup: 1. 2. 3. 4.
Hardware, Utilities and Options Other ■ Security lock ExpressCard The computer is equipped with a single ExpressCard slot into which any ExpressCard device that meets industry standards, either manufactured by TOSHIBA or another vendor, can be installed. The slot supports hot plug connection and utilizes the PCI Express interface that supports the reading and writing of data at a theoretical maximum rate of 2.5Gbps.
Hardware, Utilities and Options ExpressCard slot ExpressCard Figure 3-2 Inserting the ExpressCard (PORTÉGÉ A600) 5. After inserting the ExpressCard you should refer to its documentation and also check the configuration in Windows in order to ensure that it is correct. Removing an ExpressCard To remove an ExpressCard, follow the steps as detailed below. 1. Open the Safely Remove Hardware icon on the Windows Taskbar. 2. Point to ExpressCard and click the left Touch Pad control button. 3.
Hardware, Utilities and Options ExpressCard Figure 3-4 Removing the ExpressCard (PORTÉGÉ A600) 5. Insert the Dummy card into the ExpressCard slot. When you do not use an ExpressCard, please be sure to insert a Dummy card. SD/SDHC memory card Set the SD Card type SD memory cards and SDHC memory cards in the SD Card slot. SD/SDHC memory cards let you easily transfer data from devices, such as digital cameras and Personal Digital Assistants, that use SD/SDHC memory card flash-memory.
Hardware, Utilities and Options ■ The maximum capacity of SD memory cards is 2GB. The maximum capacity of SDHC memory cards is 16GB. Card Type Capacities SD 8MB, 16MB, 32MB, 64MB, 128MB, 256MB, 512MB, 1GB, 2GB SDHC 4GB, 8GB, 16GB Inserting an SD/SDHC memory card To insert an SD/SDHC memory card, follow the steps as detailed below: 1. Insert the SD/SDHC memory card into the SD Card slot on the side of the computer. 2. Press the SD/SDHC memory card gently to ensure a firm connection is made.
Hardware, Utilities and Options ■ Make sure the SD/SDHC memory card is oriented properly before you insert it. ■ Make sure that the SD/SDHC memory card is facing the correct direction when inserting it into the SD Card slot. ■ Do not turn the computer off or switch to Sleep Mode or Hibernation Mode while files are being copied - doing so may cause data to be lost. Removing an SD/SDHC memory card To remove an SD/SDHC memory card, follow the steps as detailed below: 1.
Hardware, Utilities and Options ■ Make sure the SD Card indicator is out before you remove the SD/SDHC memory card or turn off the computer’s power. If you remove the SD/SDHC memory card or turn off the power while the computer is accessing the SD/SDHC memory card you may lose data or damage the card. ■ Do not remove an SD/SDHC memory card while the computer is in Sleep or Hibernation Mode. The computer could become unstable or data in the SD/SDHC memory card could be lost.
Hardware, Utilities and Options For more details on using memory cards, see manuals accompanying the cards. Additional memory module You can install additional memory into the computer in order to increase the amount of system memory that is available. This section describes how to install and remove optional memory modules. ■ You should place a mat beneath the computer in order to prevent the computer's lid from becoming scratched or damaged when you are installing/replacing the memory module.
Hardware, Utilities and Options Installing a memory module To install a memory module, follow the steps as detailed below: 1. Shut down the computer - make sure the Power indicator is off (refer to the Turning off the power section in Chapter 1, Getting Started if required). 2. Remove the AC adaptor and all cables and peripherals connected to the computer. 3. Close the display panel. 4.
Hardware, Utilities and Options 7. Align the notch of the memory module with that of the memory slot and gently insert the module into the slot at about a 45 degree angle before holding it down until the latches on either side snap into place. Memory slot Figure 3-11 Seating the memory module (PORTÉGÉ R600) ■ Never allow metal objects, such as screws, staples and paper clips, to enter the computer.
Hardware, Utilities and Options 8. PORTEGE R600: Seat the memory module cover in place and secure it with two screws. PORTEGE A600: Seat the memory module cover in place and secure it with one screw. Take care to ensure that the memory module cover is firmly closed. Screws Memory module cover Figure 3-12 Seating the memory module cover (PORTÉGÉ R600) Screw Memory module cover Figure 3-13 Seating the memory module cover (PORTÉGÉ A600) 9.
Hardware, Utilities and Options 4. Turn the computer upside down and remove the battery pack (refer to Replacing the battery pack section in Chapter 6, Power and Power-Up Modes, if required). 5. PORTÉGÉ R600: Loosen the two screws securing the memory module cover in place - please note that this screw is attached to the cover in order to prevent it from being lost.
Hardware, Utilities and Options External monitor An external analog monitor can be connected to the external monitor port on the computer. To connect a monitor, follow the steps as detailed below: There are no fastening screws for an external monitor cable on this computer's external monitor port. However, external monitor cables which have connectors with fastening screws can still be used. Connecting the monitor cable 1. Turn the computer's power off. 2.
Hardware, Utilities and Options USB FDD Kit The USB floppy diskette drive accommodates either a 1.44MB or 720KB floppy diskette and connects to one of the computer's USB ports. USB connector Disk-In-Use Indicator Floppy diskette slot Eject button Figure 3-16 The USB floppy diskette drive Connecting the USB floppy diskette drive To connect the drive, plug the floppy diskette drive’s USB connector into a computer’s USB port. Make sure the connector is properly aligned with the socket.
Hardware, Utilities and Options Disconnecting the USB floppy diskette drive When you have finished using the USB floppy diskette drive, you can follow the procedures below in order to disconnect it: 1. Wait for the Disk-In-Use Indicator light to go out to make sure all floppy diskette activity has stopped. If you disconnect the USB floppy diskette drive or turn off the power while the computer is accessing the drive you may lose data or damage the floppy diskette or the drive. 2.
Hardware, Utilities and Options ■ A connected eSATA device may not be recognized if it is connected to the computer's eSATA/USB combo port while the computer is in Sleep Mode or Hibernation Mode. If this occurs, disconnect the eSATA device and then reconnect the device while the computer is turned on. ■ If you connect an eSATA device after the computer has already been turned on, it will take about ten seconds for it to be recognized by the computer.
Hardware, Utilities and Options The following ports are available on the TOSHIBA Slim Port Replicator II. ■ RJ45 LAN jack ■ External monitor port ■ DC IN 15V jack ■ Security lock slot ■ Universal Serial Bus 2.0 port (four) ■ DVI port As the port operation of all DVI (Digital Visual Interface) monitors has not been confirmed, some DVI monitors may not function properly.
Hardware, Utilities and Options Optional accessories You are able to add a number of options and accessories in order to make your computer even more powerful and convenient to use. For reference, the following list details some of the items that are available from your reseller or TOSHIBA dealer: User’s Manual DDR2-800 Memory Kit A 1,024MB, 2,048MB or 4,096MB memory module (DDR2-800) can easily be installed in the computer.
Hardware, Utilities and Options User’s Manual Wireless Optical Mouse with Bluetooth Technology The Bluetooth Wireless Mouse is a wireless optical mouse compatible with Bluetooth. You can buy the Bluetooth Wireless Mouse from a TOSHIBA dealer. Wireless Stereo Headset with Bluetooth Technology The Bluetooth Wireless Stereo is a wireless stereo headphone set compatible with Bluetooth. You can buy the Bluetooth Wireless Stereo from a TOSHIBA dealer.
Chapter 4 Operating Basics This chapter describes the basic operations of your computer, highlights the precautions that should be taken when using it. Using the Touch Pad To use the Touch Pad, simply touch and move your fingertip across it in the direction you want the on-screen pointer to go.
Operating Basics You can also tap the Touch Pad to perform functions similar to those of the left button on a standard mouse. Click: Tap once Double-click: Tap twice Drag and drop: Tap to select the item(s) you want to move, leave your finger on the Touch Pad after the second tap and then move the item(s) to their new destination. Using the Fingerprint Sensor This product has a fingerprint utility installed for the purpose of enrolling and recognizing fingerprints.
Operating Basics ■ Avoid swiping with your finger stiff or pressed too hard onto the sensor, and take care to ensure that the center of the fingerprint is touching the sensor before swiping. Either of these conditions may cause fingerprint reading to fail. ■ Check the center of the fingerprint whorl before swiping and then ensure this is swiped along the center line of the sensor.
Operating Basics Observe the following to improve the fingerprint recognition success rate. ■ Enroll two or more fingers. ■ Enroll additional fingers if a recognition failure often occurs when using already enrolled fingers. ■ Check the condition of your finger - any conditions which have changed since enrollment, such as injury, rough skin, and extremely dry, wet, soiled, dirty, oily, soaked or swollen fingers, may lower the recognition success rate.
Operating Basics 3. On the User's Fingers screen click the box above the finger you wish to register. If any of the previously enrolled fingerprints is selected again, the latest information will be enrolled and any previous information over-written. 4. The Fingerprint Enrollment screen will be displayed and the tutorial will begin. First click "Replay video" and confirm the proper movement for the finger you wish to register.
Operating Basics ■ To delete individual fingerprints 1. Click the fingerprint mark above the registered finger. 2. "Are you sure you want to delete this fingerprint?" will be displayed on the screen, click Yes button. 4. When Delete All Fingerprints is selected, the user selection screen will be displayed, so select which user's fingerprint data to delete. ■ Selecting "Delete current user's fingerprints" will delete the fingerprint data for the currently logged in user.
Operating Basics Windows Logon via Fingerprint Authentication If required, you are also able to use fingerprint authentication in place of the usual Windows logon process using your username and password. This method is especially useful where there are many users using the same computer as it removes the need for actual user selection when the system is started. Fingerprint Authentication Procedure 1. Start up the computer. 2.
Operating Basics ■ You must ensure that you use the TOSHIBA Password Utility to register a User Password before using the Fingerprint Pre-OS Authentication and its extended function to allow fingerprints to be used to access the computer when it is turned on.
Operating Basics It is necessary to register the User/BIOS Password and Windows Logon Password before using the Fingerprint Pre-OS Authentication and this Fingerprint Single-Swipe Sign On Feature. Please use the TOSHIBA Password Utility to register your User/BIOS Password. If Windows Logon is not the default for your system, see Manual to register your Windows Logon Password.
Operating Basics Web Camera Web Camera is a device that allows you to record video or take photographs with your computer. You can use it for video chatting or video conferences using a communication tool such as Windows Live Messenger. Camera Assistant Software will help you to add various video effects to your video or photograph. Enables the transmission of video and use of video chat via the internet using specialized applications. The effective pixel count for this web camera is 0.
Operating Basics Using the TOSHIBA Face Recognition TOSHIBA Face Recognition uses a face verification library to verify the face data of users when they log in to Windows. The user can thus avoid having to enter a password or the like, which makes the login process easier. Some models are preinstalled with a TOSHIBA Face Recognition. ■ TOSHIBA Face Recognition does not guarantee the correct identification of a user.
Operating Basics How to register the Face Recognition Data Take a picture for facial verification purposes, and register the data needed when you log in. To register the data needed when you log in, follow the steps as described below: 1. To launch this utility, click Start -> All Programs -> TOSHIBA -> Utilities -> TOSHIBA Face Recognition. ■ The Registration screen is displayed for a logged-in user whose face has not been registered.
Operating Basics 12. The Management screen is displayed. The registered account name will be displayed. Clicking on it will cause the captured image of your face to be displayed on the left. How to Delete the Face Recognition Data Delete image data, account information, and personal record data created during registration. To delete the Face Recognition Data, follow the steps as described below: 1. To launch this utility, click Start -> All Programs -> TOSHIBA -> Utilities -> TOSHIBA Face Recognition.
Operating Basics 6. Windows Welcome screen will be displayed, and will be logged in automatically to Windows. 1:1 Mode Login screen 1. Turn on the computer. 2. The Select Tiles screen will be displayed. 3. Select Start face recognition ( ). 4. 5. 6. 7. The Select Account screen will be displayed. Select the account, and click the arrow button. "Please turn your face to the camera" will be displayed. Verification will be performed.
Operating Basics ■ When the power of the optical disc drive is off, pressing the FN + Tab keys will turn the power of the optical disc drive on. Furthermore, it is possible to set it to turn the power of the optical disc drive on and eject the tray at the same time. ■ For models that do not provide with optical disc drives, an external optical disc drive is required to create the Recovery Discs.
Operating Basics 3. Lay the CD/DVD, label side up, in the disc tray. Laser lens Figure 4-5 Inserting a CD/DVD (PORTÉGÉ R600) ■ When the disc tray is fully opened, the edge of the computer will extend slightly over the CD/DVD tray. Therefore, you will need to turn the CD/DVD at an angle when you place it in the disc tray. After seating the CD/DVD, however, make sure it lies flat. ■ Gently support the disc tray from below with your free hand when inserting or removing CD/DVDs from the optical disc drive.
Operating Basics 5. Push the center of the disc tray to close it. Press gently until it locks into place. If the CD/DVD is not seated properly when the disc tray is closed, the CD/DVD might be damaged. Also, the disc tray might not open fully when you press the eject button. Figure 4-6 Closing the CD/DVD disc tray (PORTÉGÉ R600) Removing discs To remove the CD/DVD, follow the steps as detailed below: Do not press the eject button while the computer is accessing the media drive.
Operating Basics 2. The CD/DVD extends slightly over the sides of the disc tray so you can grasp it. Gently lift out the CD/DVD. Gently support the disc tray from below with your free hand when inserting or removing CD/DVDs from the optical disc drive. Figure 4-7 Removing a CD/DVD (PORTÉGÉ R600) Figure 4-8 Removing a CD/DVD (PORTÉGÉ A600) 3. Push the center of the disc tray to close it. Press gently until it locks into place.
Operating Basics How to remove CD/DVD when the disc tray will not open Pressing the eject button will not open the disc tray when the computer power is off. If the power is off, you can open the disc tray by inserting a slender object (about 15 mm) such as a straightened paper clip into the eject hole near the eject button. Eject hole Figure 4-9 Manual release with the eject hole (PORTÉGÉ R600) Turn off the power before you use the eject hole.
Operating Basics When writing information to media using an optical drive, you should always ensure that you connect the AC adaptor to a live power socket. It is possible that, if data is written while powered by the battery pack, the write process may sometimes fail due to low battery power - in these instances data loss may occur.
Operating Basics CD-R: TAIYO YUDEN CO., Ltd. MITSUBISHI KAGAKU MEDIA CO., LTD. Ricoh Co., Ltd. CD-RW: (Multi-Speed and High-Speed) MITSUBISHI KAGAKU MEDIA CO., LTD. Ricoh Co., Ltd. CD-RW: (Ultra-Speed) MITSUBISHI KAGAKU MEDIA CO., LTD. DVD-R: DVD Specifications for Recordable Disc for General Version 2.0 TAIYO YUDEN Co.,Ltd. (for 4x, 8x and 16x speed media) Matsushita Electric Industrial Co.,Ltd. (for 4x, 8x and 16x speed media) DVD+R: MITSUBISHI KAGAKU MEDIA CO., LTD.
Operating Basics ■ This drive cannot use discs that allow writing faster than 16x speed (DVD-R and DVD+R media), 8x speed (DVD+RW media), 6x speed (DVD-RW media), 5x speed (DVD-RAM media). ■ 2.6GB and 5.2GB DVD-RAM media cannot be read from or written to. ■ If the disc is poor in quality, or is dirty or damaged, writing or rewriting errors may be noted - ensure that you check all discs for dirt or damage before you use them.
Operating Basics ■ Do not write information while virus checking software is running, instead wait for it to finish, then disable the virus protection applications, including any software that checks files automatically in the background. ■ Do not use any hard disk utilities, including those that are intended to enhance hard disk drive access speeds, as they may cause unstable operation and damage data. ■ CD-RW (Ultra Speed +) media should not be used as data may be lost or damaged.
Operating Basics TOSHIBA Disc Creator Please be aware of the following limitations when you use the TOSHIBA Disc Creator: ■ DVD Video cannot be created using TOSHIBA Disc Creator. ■ DVD Audio cannot be created using TOSHIBA Disc Creator. ■ You cannot use TOSHIBA Disc Creator's 'Audio CD for Car or Home CD Player' function to record music to DVD-R, DVD-RW, DVD+R or DVD+RW media.
Operating Basics DVD Super Multi drive Double Layer You can use the DVD Super Multi drive to write data to either CD-R, CDRW, DVD-R, DVD-R (Dual Layer), DVD-RW, DVD+R, DVD+R (Double Layer), DVD+RW or DVD-RAM discs. The TOSHIBA Disc Creator is provided as writing software with this computer. ■ Please refer to the Writable discs, Chapter 2 for details about the types of writable CD and DVD discs that can be supported by this computer.
Operating Basics Given the technological limitations of current optical disc writing drives, you may experience unexpected writing or rewriting errors due to disc quality or problems with hardware devices. In view of this, it is good practice to make two or more copies of important data, in case of any undesired change or loss of the recorded contents.
Operating Basics DVD-RW: DVD Specifications for Recordable Disc for Version 1.1 or version 1.2 Victor Company of Japan, Ltd. (JVC) (for 2x, 4x and 6x speed media) MITSUBISHI KAGAKU MEDIA CO., LTD. (for 2x, 4x and 6x speed media) DVD+RW: Ricoh Co., Ltd. (for 2.4x, 4x and 8x speed media) MITSUBISHI KAGAKU MEDIA CO., LTD. (for 2.4x, 4x and 8x speed media) DVD-RAM: (DVD Super Multi drive only) DVD Specifications for DVD-RAM Disc for Version 2.0, Version 2.1 or Version 2.2 MITSUBISHI KAGAKU MEDIA CO., LTD.
Operating Basics ■ Data deleted/erased from a CD-RW, DVD-RW, DVD+RW or DVD-RAM disc cannot be recovered. You must check the content of the disc carefully before you delete it, taking care that, if multiple drives that can write data to discs are connected, you do not delete data from the wrong one.
Operating Basics When writing or rewriting Please observe the following points while you write or rewrite data to CD-R, CD-RW, DVD-R, DVD-R (Dual Layer), DVD-RW, DVD+R, DVD+R (Double Layer), DVD+RW or DVD-RAM media: ■ Always copy data from the hard disk drive to the optical media - do not use the cut-and-paste function as the original data will be lost if there is a write error. ■ Do not perform any of the following actions: ■ Change users in the Windows Vista operating system.
Operating Basics ■ You cannot back up CD-ROM, CD-R or CD-RW media to DVD-R, DVDR (Dual Layer) or DVD-RW media using the 'Disc Backup' function of TOSHIBA Disc Creator. ■ You cannot back up CD-ROM, CD-R or CD-RW media to DVD+R, DVD+R (Double Layer) or DVD+RW media using the 'Disc Backup' function of TOSHIBA Disc Creator.
Operating Basics 3. Select File Open or Full Compare mode. 4. Click the OK button. How to learn more about TOSHIBA Disc Creator Please refer to the Help files for additional TOSHIBA Disc Creator information. TOSHIBA DVD PLAYER This software is provided for playback of DVD Video. It has an on-screen interface and functions. Click Start -> All Programs -> TOSHIBA DVD PLAYER -> TOSHIBA DVD PLAYER. For details on how to use TOSHIBA DVD PLAYER, see the help file.
Operating Basics ■ Do not switch to Hibernation or Sleep Mode when running the "TOSHIBA DVD PLAYER". ■ Do not lock the computer using the Windows logo ( ) + L keys or the Fn + F1 keys when running the "TOSHIBA DVD PLAYER". Media care This section provides tips on protecting data stored on your CD's, DVD's and floppy diskettes. Handle your media with care. Following the simple precautions listed below will increase the lifetime of your media and protect the data stored on it. CD/DVDs 1.
Operating Basics 5. Never use a pencil for writing on a floppy diskette label as the dust from the pencil lead could cause a system malfunction if it found its way onto the computer's components. In this instance, always use a felt-tipped pen and write the label first before applying it to the floppy diskette. 6. Never put a floppy diskette in a location where water or other liquid may make contact with it, or where it is excessively damp - either of these conditions could cause data loss. 7.
Operating Basics PC Beep Level Follow the steps below to change the PC Beep playback level. 1. Right click on the speaker icon on the Taskbar, and select Playback Devices in the sub menu. 2. Select Speakers, and click Properties. 3. On the Levels tab move the Realtek HD Audio output slider to increase or decrease the PC Beep volume level. Audio Enhancements In order to apply the sound effects for your current speaker, follow the steps below. 1.
Operating Basics Default Format You can change the sample rate and bit depth of sound. TOSHIBA Mic Effect TOSHIBA Mic Effect provides you with a hands-free environment for holding mutual communication via the Internet Protocol or Local Area Network. If you wish to communicate with someone on your computer, you can use a messenger application. However, with such an application, you would hear your own voice returning to you as echo during the communication if you did not use a headset system or headphone.
Operating Basics Region selection Telecommunication regulations vary from one region to another, so you will need to make sure the internal modem’s settings are correct for the region in which it will be used. The built-in modem can be used only in specified countries and regions. Using the modem in an area not specified for use may cause a system failure. Check the specified areas carefully before using it. To select a region, follow the steps as detailed below: 1.
Operating Basics Location list for region selection. Displays a sub-menu appears which details location information. Open dialog box, if the modem and Telephony Current Location region code do not match. Displays a warning if the current settings for both region code and telephony location are different. Modem Selection If the computer cannot recognize the internal modem, a dialog box is displayed from which you should select the appropriate communications port for your modem to use.
Operating Basics 2. Plug the other end of the modular cable into a telephone jack. Telephone jack Modular cable Modem jack Figure 4-10 Connecting the internal modem (PORTÉGÉ A600) Do not pull on the cable or move the computer while the cable is connected. Disconnecting the modular cable To disconnect the modular cable, follow the steps as detailed below: 1. Pinch the lever on the plug in the telephone jack and pull it out from within the connector. 2.
Operating Basics Wireless communications The computer’s wireless communication function supports some wireless communication devices. Only some models are equipped with both Wireless LAN and Bluetooth functions. ■ Do not use the Wireless LAN (Wi-Fi) or Bluetooth functionalities near a microwave oven or in areas subject to radio interference or magnetic fields. Interference from a microwave oven or other source can disrupt Wi-Fi or Bluetooth operation.
Operating Basics ■ Frequency Channel Selection of 2.4GHz for IEEE 802.11b/g or/and IEEE802.11n draft 2.
Operating Basics Worldwide operation The Bluetooth radio transmitter and receiver operate in the 2.4GHz band, which is license-free and compatible with radio systems in most countries in the world. Radio links You can easily establish links between two or more devices, with these links being maintained even if the devices are not within a line-of-sight of each other.
Operating Basics Wireless communication switch You can enable or disable Wireless communication functions, with the on/off switch. No transmissions are sent or received when the switch is off. Slide the switch to the backward to turn it on and to the forward to turn it off. Wireless communication Indicator The wireless communication indicator shows the status of the computer's wireless communication functions.
Operating Basics If you are using Gigabit Ethernet LAN (1000 megabits per second, 1000BASE-T), be sure to connect with a CAT5E cable or higher. You cannot use a CAT3 or CAT5 cable. If you are using Fast Ethernet LAN (100 megabits per second, 100BASETX), be sure to connect with a CAT5 cable or higher. You cannot use a CAT3 cable. If you are using Ethernet LAN (10 megabits per second, 10BASE-T), you can connect with a CAT3 or higher cable.
Operating Basics Disconnecting the LAN cable To disconnect the LAN cable, follow the steps as detailed below: 1. Pinch the lever on the connector in the computer’s LAN jack and pull out the connector. 2. Disconnect the cable from the LAN hub or router in the same manner. Check with your LAN administrator and hardware or software vendor before disconnecting from the hub. Computer Handling This section explains computer handling and maintenance.
Operating Basics ■ Do not pick up the computer by its display panel. ■ Before carrying your computer, shut it down, disconnect the AC adaptor and allow it to cool down - a failure to follow this instruction may result in minor heat injury. ■ Be careful not to subject the computer to impact or shock - a failure to follow this instruction could result in damage to computer, computer failure or loss of data.
Operating Basics TOSHIBA HDD Protection Properties You can change the TOSHIBA HDD Protection settings by using the TOSHIBA HDD Protection Properties window. To open the window, click Start -> All Programs -> TOSHIBA -> Utilities -> HDD Protection Settings. The window can also be started from the icon on the Taskbar or from the Control Panel. HDD Protection You can choose whether to enable or disable TOSHIBA HDD Protection. Detection Level This function can be set to four levels.
Operating Basics Details To open the Details window, click the Setup Detail button in the TOSHIBA HDD Protection Properties window. Detection Level Amplification When the AC adaptor is disconnected or the lid is closed, HDD Detection assumes that the computer will be carried and sets the detection level to the maximum for 10 seconds. TOSHIBA HDD Protection Message Specify whether to display a message when TOSHIBA HDD Protection is active.
Operating Basics ■ When "USB Sleep and Charge function" is set to [Enabled], USB bus power (DC5V) will be supplied to compatible ports even when the power of the computer is turned OFF. USB bus power (DC5V) is similarly supplied to the external devices which are connected to the compatible ports. However, some external devices cannot be charged solely by supplying USB bus power (DC5V).
Operating Basics Enabling USB Sleep and Charge This utility can be used to enable and disable the USB Sleep and Charge function in groups. USB Sleep and Charge compatible USB ports are assigned to each group. Check the check boxes for each group to enable the USB Sleep and Charge function for the USB ports assigned to that group. In the default state all groups are disabled. Power supply mode settings There are several USB Sleep and Charge function modes. "Mode 1" should normally be used.
Chapter 5 The Keyboard The computer's keyboard layouts are compatible with a 104/105-key enhanced keyboard - by pressing some keys in combination, all of the 104/105-key enhanced keyboard functions can be performed on the computer. The number of keys available on your keyboard will depend on which country/region your computer is configured for, with keyboards being available for numerous languages.
The Keyboard Function keys: F1 … F12 The function keys (not to be confused with the special FN key) are the twelve keys at the top of your keyboard - these keys function differently from other keys. F1 through F12 are called function keys because they execute programmed functions when pressed and, when used in combination with the FN key, those keys marked with icons also execute specific functions on the computer.
The Keyboard Press FN + F10 or FN + F11 to access the computer's integrated keypad. When activated, the keys with grey markings on their bottom edge become either numeric keypad keys (FN + F11) or cursor control keys (FN + F10). Please refer to the Keypad overlay section in this chapter for more information on how to operate these keys, taking care to note that the power on default for both settings is off. Press FN + F12 (ScrLock) to lock the cursor on a specific line. The power on default is off.
The Keyboard Sleep: Pressing FN + F3 switches the system to Sleep Mode. Hibernate: Pressing FN + F4 switches the system to Hibernation Mode. Output: Pressing FN + F5 changes the active display device. To use a simultaneous mode, you must set the resolution of the internal display panel to match the resolution of the external display device. Brightness Down: Pressing FN + F6 decreases the computer's display panel brightness in individual steps.
The Keyboard ODD: Pressing FN + Tab turns the power of the optical disc drive on/off or ejects the disc tray. TOSHIBA Zooming Utility (reduce): Pressing FN + 1 reduces the icon size on the desktop or the font sizes within one of the supported application windows. TOSHIBA Zooming Utility (enlarge): Pressing FN + 2 enlarges the icon size on the desktop or the font sizes within one of the supported application windows.
The Keyboard Keypad overlay Your computer's keyboard does not have a separate numeric keypad but includes a numeric keypad overlay which functions like one - this is located in the center of the keyboard with the relevant keys having grey letters at their front edge. The overlay provides the same functions as the numeric keypad on a standard 104/105-key enhanced keyboard. Turning on the overlays The numeric keypad overlay can be used for numeric data input or cursor and page control.
The Keyboard Temporarily using normal keyboard (overlay on) While using the overlay, you can temporarily access the normal keyboard functions without having to turn the overlay off: 1. Hold down FN key and press any other key - this key will operate as if the overlay were off. 2. Type upper-case characters by holding down FN + SHIFT and pressing a character key. 3. Release FN key to continue using the selected overlay function.
Chapter 6 Power and Power-Up Modes The computer's power resources include the AC adaptor, battery pack and any internal batteries. This chapter provides details on making the most effective use of these resources, and includes information on charging and changing batteries, tips for saving battery power, and information on the different power-up modes.
Power and Power-Up Modes Battery partially • Operates charged or no • Charge charge • LED: Battery orange DC IN white or green • Quick charge No battery installed • Operates • No charge • No charge • LED: • LED: Battery orange DC IN white or green • LED: Battery off DC IN white or green Battery off DC IN white or green Table 6-1 Power conditions continued Power on AC adaptor not connected Battery charge is above low battery trigger point • Operates Battery charge is below low battery trigger
Power and Power-Up Modes Monitoring of power condition As shown in the below table, the Battery, DC IN and Power indicators on the system indicator alert you to the computer’s operating capability and battery charge status. Battery indicator Check the Battery indicator to determine the status of the battery pack. The following indicator lights indicate the battery status: Flashing orange The battery charge is low, the AC adaptor must be connected in order to recharge the battery.
Power and Power-Up Modes Power indicator Check the Power indicator to determine the power status of the computer the following indicator conditions should be noted: White or green Indicates power is being supplied to the computer and the computer is turned on. Blinking orange Indicates that the computer is in Sleep Mode and that there is sufficient power available (AC adaptor or battery) to maintain this condition. In Sleep Mode, this indicator will turn on for one second and off for two seconds.
Power and Power-Up Modes You can change the Real Time Clock settings by turning the computer on while pressing the ESC key and then the F1 key when prompted. Please refer to Chapter 8 Troubleshooting for further information. The RTC battery does not charge while the computer is turned off even if the AC adaptor is attached. Care and use of the battery pack This section provides the important safety precautions in order to handle your battery pack properly.
Power and Power-Up Modes Charging the batteries When the power in the battery pack becomes low, the Battery indicator will flash orange to indicate that only a few minutes of battery power remain. If you continue to use the computer while the Battery indicator flashes, the computer will enable Hibernation Mode so that you do not lose any data, and automatically turn itself off. You must recharge a battery pack when it becomes discharged.
Power and Power-Up Modes Monitoring battery capacity Remaining battery power can be monitored using the following methods. ■ Clicking the battery icon on the Taskbar ■ Via the Battery Status in the Windows Mobility Center window ■ You should wait at least 16 seconds after turning on the computer before trying to monitor the remaining operating time.
Power and Power-Up Modes Maximizing battery operating time A battery's usefulness depends on how long it can supply power on a single charge, while how long the charge lasts in a battery depends on: ■ Processor speed ■ Screen brightness ■ System Sleep Mode ■ System Hibernation Mode ■ Display power off period ■ Hard disk drive power off period ■ How often and for how long you use the hard disk drive and external disk(c) drives, for example, optical disc and floppy diskette drive.
Power and Power-Up Modes Extending battery life To maximize the life of your battery packs: ■ At least once a month, disconnect the computer from a power source and operate it on battery power until the battery pack fully discharges. Before doing so, follow the steps as detailed below. 1. Turn off the computer's power. 2. Disconnect the AC adaptor and turn on the computer's power - if it does not turn on then go to Step 4. 3. Operate the computer on battery power for five minutes.
Power and Power-Up Modes Replacing the battery pack Please be aware that the battery pack is classified as a consumable item. The operating life of the battery pack will gradually reduce through repeated charging and discharging, and will need to be replaced when it reaches the end of its operating life. In addition to this, you might also replace a discharged battery pack with a charged spare when you are operating your computer away from an AC power source for an extended period of time.
Power and Power-Up Modes Installing the battery pack To install a battery pack, follow the steps as detailed below: Do not touch the battery release latch while holding the computer or the battery pack might fall out due to the unintentional release of the battery release latch and cause injuries. 1. Insert the battery pack as far as it will go into the computer (1). 2. Ensure that the battery pack is securely in place and the battery lock (2) is in its ( ) position.
Power and Power-Up Modes User Password field ■ Set (button) Click this button to register a password of up to 50 characters. After a password is set, you will be prompted to enter it when you start the computer. Check "Set the same string simultaneously as the HDD User Password" when setting the HDD User Password. ■ After you set the password, a dialog box will be displayed asking whether you want to save it to a floppy diskette or other media.
Power and Power-Up Modes ■ If you forget your HDD User Password, TOSHIBA will NOT be able to assist you, and your HDD will be rendered COMPLETELY and PERMANENTLY INOPERABLE. TOSHIBA will NOT be held responsible for any loss of any data, any loss of use or access to your HDD, or for any other losses to you or any other person or organization that result from the loss of access to your HDD. If you can’t accept this risk, don’t register the HDD User Password.
Power and Power-Up Modes This function in the TOSHIBA Password Utility lets you invalidate only supervisor tokens or all tokens, including user and supervisor tokens. ■ Specify restrictions for general users. Starting the computer by password If you have already registered a password, there are three ways to start the computer: ■ Insert an SD Card token before you turn on the computer. The computer will start normally, without displaying a password prompt.
Power and Power-Up Modes Windows utilities You can configure various settings associated with both Sleep Mode and Hibernation Mode within the Power Options (to access it, Start -> Control Panel -> System and Maintenance -> Power Options). Hot keys You can use the FN + F3 hot key to enter Sleep Mode or FN + F4 to enter Hibernation Mode - please refer to Chapter 5, The Keyboard for further details.
Chapter 7 HW Setup This chapter explains how to use the TOSHIBA HW Setup program to configure your computer, and provides information on settings for various functions. Accessing HW Setup To run the HW Setup program, click Start -> All Programs -> TOSHIBA -> Utilities -> HWSetup. HW Setup window The HW Setup window contains a number of tabs (General, Display, Boot Priority, Keyboard, CPU, LAN, Device Config and USB) to allow specific functions of the computer to be configured.
HW Setup General This window displays the BIOS version and contains two buttons : Default and About. Default Return all HW Setup values to the factory settings. About Display the HW Setup version. Setup This field displays the installed BIOS version and date. Display This tab lets you customize your computer’s display settings for either the internal display or an external monitor. Power On Display This tab allows you to select the display to be used when the computer is started.
HW Setup Boot Priority Boot Priority Options This tab allows you to select the priority for booting the computer - the following settings are available: FDD −> HDD −> CDROM −> LAN The computer looks for bootable files on devices in the following order: 1. floppy diskette drive*1, 2. hard disk drive, 3. CD-ROM*2, 4. LAN. HDD −> FDD −> CDROM −> LAN The computer looks for bootable files on devices in the following order: 1. hard disk drive, 2. floppy diskette drive*1, 3. CD-ROM*2, 4. LAN.
HW Setup To change the boot drive, follow the steps below. 1. Hold down F12 and boot the computer. 2. The following menu will be displayed with the following icons: Built-in hard disk drive, CD-ROM, FDD (or SD memory card), Network (LAN), USB Memory boot. Please note that a highlighted bar will only appear under the selected device. 3. Use the left/right cursor keys to highlight the boot device you want and press ENTER.
HW Setup USB Memory BIOS Support Type This option allows you to set the type of the USB memory to be used as a startup device. HDD Sets the USB memory to be the equivalent of a hard disk drive (default). With this setting, the USB memory device can be used to start the computer as though it were a hard disk drive based on the hard disk drive settings within both the Boot Priority and HDD Priority options detailed previously. FDD Sets the USB memory to be the equivalent of a floppy diskette drive.
HW Setup CPU This function allows you to set the processor's operating mode. Dynamic CPU Frequency Mode This option allows you to configure the power saving modes associated with the processor - the following settings are available: Dynamically Switchable The processor's power consumption and automatic clock speed switching functions are enabled - in use the processor's operation is automatically switched when necessary (default).
HW Setup Built-in LAN This feature enables or disables the Built-in LAN. Enabled Enables Built-in LAN functions (Default). Disabled Disables Built-in LAN functions. Device Config Device Configuration This option allows you to set how the computer's hardware devices will be configured. All Devices The computer's BIOS will setup and configure all devices. Setup by OS The operating system will setup and configure all of the devices that it can control (default).
Chapter 8 Troubleshooting TOSHIBA have designed this computer for durability, however, should problems occur you are able to use the procedures detailed in this chapter to help determine the cause. All users should become familiar with this chapter as knowing what might go wrong can help prevent problems from occurring in the first place.
Troubleshooting Preliminary checklist You should always consider the simplest solution first - the items detailed in this checklist are easy to fix and yet can cause what appears to be a serious problem: ■ Make sure you turn on all peripheral devices before you turn on the computer - this includes your printer and any other external device you are using.
Troubleshooting ■ Do you hear any beeps, if so how many, are they long or short and are they high pitched or low pitched? In addition, is the computer making any unusual noises? Write down what you hear. Record your observations so you can describe them in detail to your reseller, dealer or service provider. Software Hardware The problems may be caused by your software or disk.
Troubleshooting System start-up When the computer does not start properly, check the following items: ■ Self Test ■ Power Sources ■ Power-on Password Self test While booting up the computer, self test is executed automatically and the TOSHIBA logo is displayed on the screen. This logo remains on the screen for a few seconds. If the self test is successful, the computer tries to load the operating system according to how the Boot Priority option is set within the TOSHIBA HW Setup program.
Troubleshooting Overheating power down If the processor's temperature reaches an unacceptably high level with either setting, the computer will automatically shuts down to prevent any damage - in this instance all unsaved data in memory will be lost. Problem Procedure Computer shuts down and DC IN indicator blinks orange Leave the computer off until the DC IN indicator stops blinking.
Troubleshooting Battery If you suspect a problem with the battery, you should check the status of the DC IN indicator as well as the Battery indicator. Please refer to Chapter 6, Power and Power-Up Modes for more information on these indicators, together with general battery operation. Problem Procedure Battery doesn’t power the computer The battery may be discharged - connect the AC adaptor to recharge the battery.
Troubleshooting Real Time Clock Problem Procedure The following message is Displayed on the screen: RTC battery is low or CMOS checksum is inconsistent. Press [F1] key to set Date/Time. The charge in the Real Time Clock (RTC) battery has run out - you will need to set the date and time in the BIOS setup application by using the following steps: 1. Press the F1 key - the BIOS setup application will load. 2. Set the date in the System Date field. 3. Set the time in the System Time field. 4.
Troubleshooting Internal display panel Apparent computer's display panel problems may be related to the computer's setup and configuration - please refer to Chapter 7, HW Setup, for further information. Problem Procedure No display Press the FN + F5 hot keys to adjust the display priority, and to make sure it is not set for output to an external monitor. Markings appear on the These marks may have come from contact with computer's display the keyboard and Touch Pad while the display panel.
Troubleshooting Problem Procedure Slow performance The files on the hard disk drive may be fragmented - in this instance you should run the disk Defragmentation utility to check the condition of your files and the hard disk drive. Please refer to the operating system's documentation or online Help File for further information on operating and using the Defragmentation utility. As a last resort you should reformat the hard disk drive and then reload the operating system and all other files and data.
Troubleshooting Check the type of CD/DVD you are using. The drive supports: DVD-ROM: DVD-ROM, DVD-Video CD-ROM: CD-DA, CD-Text, Photo CD (single/multi-session), CD-ROM Mode 1, Mode 2, CD-ROM XA Mode 2 (Form1, Form2), Enhanced CD (CD-EXTRA), Addressing Method 2 ■ DVD Super Multi drive Recordable DVD: DVD-R, DVD+R, DVD-RW, DVD+RW, DVD-RAM ■ DVD Super Multi drive Double Layer Recordable DVD: DVD-R/-R DL, DVD+R/+R DL, DVD-RW, DVD+RW, DVD-RAM Check the region code on the DVD.
Troubleshooting ExpressCard For further information, please refer to Chapter 3, Hardware, Utilities and Options. Problem Procedure ExpressCard error occurs Remove the ExpressCard from the computer and then reinsert it in order to ensure it is firmly connected. In the event that the ExpressCard is attached to an external peripheral device, ensure that this connection is properly made.
Troubleshooting Pointing device If you are using a USB mouse, you should also refer to both the USB device section in this chapter, and the documentation supplied with your mouse. Touch Pad Problem Procedure On-screen pointer does In this instance the system might be busy - Try not respond to pointing moving the mouse again after waiting a short device operation while.
Troubleshooting Problem Procedure The reaction of Touch pad is either too sensitive or not sensitive enough. Adjust the touch Sensitivity. 1. Click Start -> Control Panel -> Hardware and Sound -> Mouse icon. 2. Within the Mouse Properties window, click the Advanced tab. 3. Click the Advanced feature settings... button. 4. Advanced feature settings is displayed. 5. Within the Pointer speed and tapping settings, click Settings... button. 6. Detailed Touch Pad settings window is displayed. 7.
Troubleshooting Problem Procedure The on-screen pointer moves too fast or too slow In this instance, you should initially try changing the speed setting within the Mouse Control utility. 1. To access this utility, click Start -> Control Panel -> Hardware and Sound -> Mouse icon. 2. Within the Mouse Properties window, click the Pointer Options tab. 3. Set the pointer speed as required and click OK.
Troubleshooting USB device In addition to the information in this section, please also refer to the documentation supplied with your USB device. Problem Procedure USB device does not work Remove the USB device from the computer and then reconnect it to a free port it in order to ensure it is firmly attached. Ensure that any required USB device drivers are properly installed - to achieve this you should refer to both the device documentation and the operating system documentation.
Troubleshooting Problem Procedure Some external devices may not be able to use the "USB Sleep and Charge function". In this case, please try one or more of the following methods. ■ Select another Mode. ■ Turn OFF the computer while external devices are connected. ■ Connect external devices after turning OFF of the computer. If this function can not be still used, change the setting to [Disabled] and stop using this function. The battery depletes quickly even when I turned OFF the power of the computer.
Troubleshooting eSATA device In addition to the information in this section, please also refer to the documentation supplied with your eSATA device. Problem Procedure eSATA device does not work Remove the eSATA device from the computer and then reconnect it to a free port it in order to ensure it is firmly attached. A connected eSATA device may not be recognized if it is connected to the computer's eSATA/USB combo port while the computer is in Sleep Mode or Hibernation Mode.
Troubleshooting Sound system In addition to the information in this section, please also refer to the documentation supplied with your audio device. Problem Procedure No sound is heard Adjust the volume control dial. To increase the volume move the volume control dial to the left, and to decrease it move the volume control dial to the right. Check the software volume settings. Please check to see if Mute is turned to Off. Check to make sure the headphone connection is secure.
Troubleshooting Volume control dial Problem Procedure No sound is heard Adjust the volume control dial. To increase the volume move the volume control dial to the left, and to decrease it move the volume control dial to the right. Turn the volume control dial while verifying the volume in order to adjust. Annoying sound is heard Volume cannot be adjusted during Windows start up or shut down. If you are still unable to resolve the problem, contact your reseller, dealer or service provider.
Troubleshooting Problem Procedure No display Try adjusting the contrast and brightness controls on the external monitor. Press the FN + F5 hot key in order to change the display priority and ensure that it is not set for the internal display only. Check to see if the external monitor is connected.
Troubleshooting Problem Procedure You place a call, but a connection can’t be made Make sure that the settings are correct within your communication application. After making a call you can’t hear a ring Ensure that the communication application's tone or pule dialling selection feature is set correctly.
Troubleshooting Wireless LAN If the following procedures do not restore LAN access, consult your LAN administrator. For more information on wireless communication, refer to Chapter 4, Operating Basics. Problem Procedure Cannot access Wireless LAN Make sure the computer's Wireless communication switch is set to on. Wake-up on Wireless LAN does not work Make sure the AC adaptor is connected. The Wake-up on Wireless LAN function consumes power even when the system is off.
Troubleshooting Recovery Discs Problem Procedure The following message appears when executing Recovery Disc Creator. "The Recovery Disc Creator can not be launched because there is no recovery partition." You will see this message if you have previously chosen to remove the partition and are trying to create "Recovery Media". When there is no recovery partition, the Recovery Disc Creator cannot make Recovery Media.
Troubleshooting Where to write If you are still unable to solve the problem and suspect that it is hardware related, write to TOSHIBA at the nearest location listed below: User’s Manual Outside of Europe In Europe Australia TOSHIBA Australia Pty. Ltd. Information Systems Division Building C, 12-24 Talavera Rd, North Ryde, 2113, NSW, Australia. Germany & Austria TOSHIBA Europe (I.E.) GmbH Geschäftsbereich, Deutschland-Österreich Hammfelddamm 8, D-41460 Neuss, Germany Canada TOSHIBA of Canada Ltd.
Appendix A Specifications This appendix summarizes the computer’s technical specifications. Physical Dimensions Refer to User Information Guide about Size.
Specifications Power Requirements AC adaptor 100-240 volts AC 50 or 60 hertz (cycles per second) Computer 15 V DC 3.0/4.0 amperes (different for each model) Built-in Modem This information is applicable to the models equipped with a built-in modem.
Specifications User’s Manual Communication speed Data transmission and reception 300/1200/2400/4800/7200/9600/12000/14400/16 800/19200/21600/24000/26400/28800/31200/33 600 bps Data reception only with V.
Appendix B Display Controller and Video mode Display controller The display controller interprets software commands into hardware commands that turn particular parts on the screen on or off. Due to the display panel's increased resolution, lines may appear broken in when displaying images in full-screen text mode. The display controller also controls the video mode and uses industry standard rules to govern the screen resolution and the maximum number of colors that can be displayed at any one time.
Appendix C Wireless LAN This appendix is intended to help you get your Wireless LAN network up and running, with a minimum of parameters. Card Specifications Form Factor Compatibility Network Operating System Media Access Protocol User’s Manual PCI Express Mini Card ■ IEEE 802.11 Standard for Wireless LANs ■ Wi-Fi (Wireless Fidelity) certified by the Wi-Fi Alliance. The ‘Wi-Fi CERTIFIED’ logo is a certification mark of the Wi-Fi Alliance.
Wireless LAN Radio Characteristics Radio Characteristics of Wireless LAN module may vary according to: ■ Country/region where the product was purchased ■ Type of product Wireless communication is often subject to local radio regulations. Although Wireless LAN wireless networking products have been designed for operation in the license-free 2.4GHz and 5GHz* band, local radio regulations may impose a number of limitations to the use of wireless communication equipment.
Wireless LAN Supported Frequency Sub-bands Subject to the radio regulations that apply in the countries/regions, your Wireless LAN module may support a different set of 5 GHz/2.4 GHz channels. Consult your Authorized Wireless LAN or TOSHIBA Sales office for information about the radio regulations that apply in the countries/regions. New wireless network adapter "AR9281" supports IEEE802.11b/g/draft-n but does not support IEEE802.11a. 2.4GHz Band Channels Sets (Wireless IEEE 802.
Wireless LAN ■ For wireless clients that operate in a Wireless LAN Infrastructure, the Wireless LAN module will automatically start operation at the channel identified by the Wireless LAN Access Point. When roaming between different access points the station can dynamically switch to another channel if required.
Wireless LAN 153 5765*1 157 5785*1 161 5805*1 165 5825*1 *1 The channel which can be used depends on the installed wireless LAN module. And the approved channels on using are different at each country or region. The channel configuration is managed as follows: ■ For wireless clients that operate in a Wireless LAN Infrastructure, the Wireless LAN module will automatically start operation at the channel identified by the Wireless LAN Access Point.
Appendix D Bluetooth wireless technology Interoperability Bluetooth Adaptor from TOSHIBA are designed to be interoperable with any product with Bluetooth wireless technology that is based on Frequency Hopping Spread Spectrum (FHSS) radio technology, and is compliant to: ■ Bluetooth Specification Ver. 2.1+EDR, as defined and approved by The Bluetooth Special Interest Group. ■ Logo certification with Bluetooth wireless technology as defined by The Bluetooth Special interest Group.
Bluetooth wireless technology Interoperability Bluetooth wireless technology and your Health The products with Bluetooth wireless technology, like other radio devices, emit radio frequency electromagnetic energy. The level of energy emitted by devices with Bluetooth wireless technology however is far much less than the electromagnetic energy emitted by wireless devices like for example mobile phones.
Bluetooth wireless technology Interoperability USA-Federal Communications Commission (FCC) This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy.
Bluetooth wireless technology Interoperability Taiwan Article 12 Without permission granted by the DGT or NCC, any company, enterprise, or user is not allowed to change frequency, enhance transmitting power or alter original characteristic as well as performance to an approved low power radio-frequency devices.
Bluetooth wireless technology Interoperability 2. Indication The indication shown below appears on this equipment. (1) 2.4 : This equipment uses a frequency of 2.4 GHz. (2) FH : This equipment uses FH-SS modulation. (3) 1: The interference range of this equipment is less than 10 m. (4) This equipment uses a frequency bandwidth from 2,400 MHz to 2,483.5 MHz. It is impossible to avoid the band of mobile object identification systems. 3.
Appendix E AC Power Cord and Connectors The power cord’s AC input plug must be compatible with the various international AC power outlets and the cord must meet the standards for the country/region in which it is used. All cords must meet the following specifications: Length: Minimum 1.7 meters Wire size: Minimum 0.75 mm2 Current rating: Minimum 2.5 amperes Voltage rating: 125 or 250 VAC (depending on country/region’s power standards) Certification agencies U.S.
AC Power Cord and Connectors Finland: FIMKO Sweden: SEMKO France: LCIE Switzerland: SEV Germany: VDE United Kingdom: BSI In Europe, two conductors power cord must be VDE type, H05VVH2-F or H03VVH2-F and for three conductors power cord must be VDE type, H05VV-F. For the United States and Canada, two pin plug configuration must be a 215P (250V) or 1-15P (125V) and three pin plug configuration must be 615P (250V) or 5-15P (125V) as designated in the U.S.
Appendix F TOSHIBA Anti-theft Protection Timer This feature allows you to set up a timer-activated BIOS password that will prevent unauthorised system access in the event of theft. When the time limit is exceeded, you are required to provide the Password or fingerprint authentication for the BIOS and Hard Disk Drive to gain access to the system. To set permissions and limits for the TOSHIBA Anti-theft Protection Timer please use the TOSHIBA Password Utility.
Appendix G TOSHIBA PC Health Monitor The TOSHIBA PC Health Monitor software program monitors computer system functions such as power consumption, the cooling system and HDD Drop sensor. It alerts users of specific system conditions via pop-up messages. It also tracks the usage of the computer and related devices, logging the service relevant information on the computer's hard disk drive. Please see the separate instructions for more detailed information on TOSHIBA PC Health Monitor operations.
Appendix H Legal Footnotes This chapter states the Legal Footnotes information applicable to TOSHIBA computers. In the text in this manual, *XX is used to show which Legal Footnotes description is related to TOSHIBA computers. Description(s) related to this computer are marked with a blue *XX in this manual. Clicking on *XX will display the related description. Non-applicable Icons*1 Certain computer chassis are designed to accommodate all possible configurations for an entire product series.
Legal Footnotes ■ use of computer at temperatures outside the range of 5°C to 30°C (41°F to 86°F) or >25°C (77°F) at high altitude (all temperature references are approximate and may vary depending on the specific computer model - please refer to your computer documentation or visit the Toshiba website at www.pcsupport.toshiba.com for details). CPU performance may also vary from specifications due to design configuration. Under some conditions, your computer product may automatically shutdown.
Legal Footnotes Battery Life*4 Battery life may vary considerably depending on product model, configuration, applications, power management settings and features utilized, as well as the natural performance variations produced by the design of individual components. Published battery life numbers are achieved on select models and configurations tested by Toshiba at the time of publication. Recharge time varies depending on usage. Battery may not charge while computer is consuming full power.
Legal Footnotes Wireless LAN*8 The transmission speed over the wireless LAN and the distance over which wireless LAN can reach may vary depending on surrounding electromagnetic environment, obstacles, access point design and configuration, and client design and software/hardware configurations. The actual transmission speed will be lower than the theoretical maximum speed. To use the Atheros SuperAG™ or SuperG™ function, your client and access point must support the corresponding feature.
Glossary The terms in this glossary cover topics related to this manual. Alternate naming is included for reference.
Glossary I/O: input/output IRQ: interrupt request KB: kilobyte LAN: local area network LCD: liquid crystal display LED: light emitting diode MB: megabyte OCR: optical character recognition (reader) PC: personal computer PCI: peripheral component interconnect RAM: random access memory RGB: red, green, and blue ROM: read only memory RTC: real time clock SDRAM: synchronous dynamic random access memory SLI: Scalable Link Interface SO-DIMM: small-outline dual in line memory module SSD: Solid state drive TFT: th
Glossary application: A group of programs that together are used for a specific task such as accounting, financial planning, spreadsheets, word processing and games. ASCII: American Standard Code for Information Interchange. ASCII code is a set of 256 binary codes that represent the most commonly used letters, numbers, and symbols. asynchronous: Lacking regular time relationship.
Glossary C cache memory: A section of very fast memory in which frequently used information is duplicated for quick access. Accessing data from cache is faster than accessing it from the computer's main memory. See also L1 cache, L2 cache. capacity: The amount of data that can be stored on a magnetic storage device such as a floppy diskette or hard disk drive.
Glossary computer program: A set of instructions written for a computer that enable it to achieve a desired result. computer system: A combination of hardware, software, firmware, and peripheral components assembled to process data into useful information. configuration: The specific components in your system (such as the terminal, printer, and disk drives) and the settings that define how your system works. You use the HW Setup program to control your system configuration.
Glossary display: A CRT, LCD, or other image producing device used to view computer output. documentation: The set of manuals and/or other instructions written for the users of a computer system or application. Computer system documentation typically includes procedural and tutorial information as well as system functions. double click: To press and release the pointing device's primary button rapidly twice without moving the pointing device.
Glossary F fast infrared: An industry standard that enables cableless infrared serial data transfer at speeds of up to 4 Mbps. file: A collection of related information; a file can contain data, programs, or both. fingerprint sensor: The fingerprint sensor compares and analyzes the unique characteristics in a fingerprint. firmware: A set of instructions built into the hardware which controls and directs a microprocessor’s activities. flash memory: Non-volatile memory that can be written to as well as read.
Glossary host computer: The computer that controls, regulates, and transmits information to a device or another computer. hot key: The computer’s feature in which certain keys in combination with the extended function key, FN, can be used to set system parameters, such as speaker volume. HW Setup: A TOSHIBA utility that lets you set the parameters for various hardware components. I icon: A small graphic image displayed on the screen or in the indicator panel.
Glossary L L1 cache: Level one cache. Memory cache built into the processor to help improve processing speed. See also cache memory, L2 cache. L2 cache: Memory cache installed on the motherboard to help improve processing speed. It is slower than L1 cache and faster than main memory. See also cache memory, L1 cache. LAN: A group of computers or other devices dispersed over a relatively limited area and connected by a communications link that enables any device to interact with any other on the network.
Glossary MP3: An audio compression standard that enables high-quality transmission and real-time playback of sound files. N network: A collection of computers and associated devices that are connected by communications facilities. A network allows you to share data and peripheral devices, such as printers, with other users and to exchange electronic mail. non-system disk: A disk for storing programs and data that cannot be used to start the computer. Compare system disk.
Glossary peripheral: Any device, such as a printer or joystick, that is attached to the computer and controlled by the computer's CPU. pixel: A picture element. The smallest dot that can be made on a display or printer. Also called a pel. plug and play: A capability with Windows that enables the system to automatically recognize connections of external devices and make the necessary configurations in the computer.
Glossary S SCSI: Small Computer System Interface is an industry standard interface for connection of a variety of peripheral devices. SD/SDHC memory card: Secure Digital cards are flash memory widely used in a variety of digital devices such as digital cameras and Personal Digital Assistants. SIO: Serial Input/Output. The electronic methodology used in serial data transmission.
Glossary W warm start: Restarting or resetting a computer without turning it off. Wi-Fi: A registered trademark term of the Wi-Fi Alliance that stands for Wireless Fidelity, and is another term for the communication protocol to permit an Ethernet connection using wireless communication components. window: A portion of the screen that can display its own application, document or dialog box. Often used to mean a Microsoft Windows window. Wireless LAN: Local Area Network (LAN) through wireless communication.
Index A AC adaptor 3-3 additional 3-32 connecting 1-4 ASCII characters 5-7 B Back light On/Off button 3-6 Battery charging 6-6 extending life 6-9 indicator 2-14, 6-3 monitoring capacity 6-7 real time clock 3-3, 6-4 save mode 3-8 types 6-4 Battery pack 2-7, 3-2 additional 6-1 replacing 6-10 Bluetooth 3-6, 4-40 Bluetooth Stack for Windows by Toshiba 3-13 Bluetooth USB Adaptor 3-32 problems 8-22 Wireless Optical Mouse 3-33 Wireless Stereo Headset 3-33 Boot Priority 7-3 C Cleaning the computer 4-44 Cooling ve
PORTÉGÉ R600/PORTÉGÉ A600 FN + ESC (Mute) 5-3 FN + F1 (Lock) 5-3 FN + F10 (Arrow Mode) 5-3 FN + F11 (Numeric Mode) 5-3 FN + F12 (ScrLock) 5-3 FN + F2 (Power Plan) 5-3 FN + F3 (Sleep) 5-4 FN + F4 (Hibernate) 5-4 FN + F5 (Output) 5-4 FN + F6 (Brightness Down) 5-4 FN + F7 (Brightness Up) 5-4 FN + F8 (Wireless) 5-4 FN + F9 (Touch Pad) 5-4 FN + space (Zoom) 5-4 FN + Tab (ODD) 5-5 Function keys 5-2 G Graphics controller 3-4 H Hard disk drive 3-3 automatic power off 3-7 Hard Disk Drive or Hard Disk Drive/Optica
PORTÉGÉ R600/PORTÉGÉ A600 problems 8-17 removing 3-25 Modem 3-5 connecting 4-37 disconnecting 4-38 jack 2-5 problems 8-20 properties menu 4-36 region selection 4-36 Moving the computer 4-44 P Password power on 3-7 problems 8-7 Starting the computer by 6-14 Supervisor 6-13 user 6-11 Pointing Device Touch Pad 2-12, 4-1, 8-12 Touch Pad control buttons 2-12, 4-1 Touch Pad location 2-10, 2-11 using 4-1 Power conditions 6-1 Hibernation Mode 1-10 indicators 6-3 panel on/off 3-8, 6-15 Shut Down Mode 1-7 Sleep Mod
PORTÉGÉ R600/PORTÉGÉ A600 microphone jack 2-3 problems 8-18 speaker 2-12 volume control dial 2-4 T TOSHIBA Assist 3-13 TOSHIBA Assist button 3-6 TOSHIBA ConfigFree 3-13 TOSHIBA Disc Creator 3-14, 4-24, 4-29 TOSHIBA DVD-RAM Utility 3-14 TOSHIBA HDD Protection 3-8 TOSHIBA Mic Effect 3-13 TOSHIBA PC Diagnostic Tool 3-11 TOSHIBA Presentation button 3-7 TOSHIBA SD Memory Boot Utility 3-13 TOSHIBA SD Memory Card Format 3-13 TOSHIBA Slim Port Replicator II 3-32 TOSHIBA Value Added Package 3-10 TOSHIBA Zooming Ut
