E3TK6BD_EN.book Page 1 Wednesday, February 17, 2010 10:18 AM Introduction Basic Setup / TV View Operation RDXV60KB Connections HDD & DVD / VIDEO CASSETTE RECORDER OWNER’S MANUAL Recording PAL Playback Editing Function Setup EN VCR HDD DVD HDD DVD For Customer Use: Carefully read the Model No. and Serial No. located at the back of the unit and enter the information below. Retain this information for future reference. Model No. __________________________ Serial No.
E3TK6BD_EN.book Page 2 Wednesday, February 17, 2010 10:18 AM . Introduction Precautions WARNING: TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE. The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to the presence of uninsulated “dangerous voltage” within the product’s enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons.
E3TK6BD_EN.book Page 3 Wednesday, February 17, 2010 10:18 AM Installation Location For safety and optimum performance of this unit: • Install the unit in a horizontal and stable position. • Keep the unit away from electronic equipment such as an amplifier, TV, etc. to prevent warping,damage, fire and malfunction. • Do not place anything directly on top of the unit. • Shield the unit from direct sunlight and keep away from sources of intense heat. Avoid dusty or humid locations.
E3TK6BD_EN.book Page 4 Wednesday, February 17, 2010 10:18 AM Notice for the Progressive Scan Outputs Consumers should note that not all high definition television sets are fully compatible with this product and may cause artifacts to be displayed in the picture. In case of picture problems with 480 or 576 progressive scan output, it is recommended that the user switch the connection to the ‘standard definition’ output.
E3TK6BD_EN.book Page 5 Wednesday, February 17, 2010 10:18 AM VCR The following features are available with this unit.
E3TK6BD_EN.book Page 6 Wednesday, February 17, 2010 10:18 AM Table of Contents Introduction ...................................................... 2 Editing ............................................................. 58 Precautions ........................................................................ 2 Guide to a Title List .......................................................... 58 Features ............................................................................. 5 Editing Discs .......
E3TK6BD_EN.book Page 7 Wednesday, February 17, 2010 10:18 AM Introduction Guide to the Owner’s Manual Symbols Used in the Owner’s Manual Symbol Connections To show what recording mode or media type applies to each function, the following symbols appear at the beginning of each operating item.
E3TK6BD_EN.book Page 8 Wednesday, February 17, 2010 10:18 AM Media for Recording / Playing Media Type DVD-RW DVD-R DVD+RW DVD+R HDD Logo Automatically Format Can be formatted in VR or video mode formatted in video mode Video Mode Icon Maximum Record Time VR DVD-RW DVD-RW 480 min (12 cm) 144 min (8 cm) 480 min (12 cm) 144 min (8 cm) Available Features DVD-R 480 min (12 cm) 144 min (8 cm) 1×-6× Recordable/Playable Ver. 1.1/1.2 Versions Ver. 1.1/1.
E3TK6BD_EN.book Page 9 Wednesday, February 17, 2010 10:18 AM Introduction Discs for Playing Disc Type DVD-VIDEO CD-DA Video CD CD-RW CD-R Logo Icon CD VCD CD CD Connections DVD-V Files for Playing MP3 JPEG DivX® Icon MP3 JPEG DivX CD-RW/-R USB device CD-RW/-R USB device CD-RW/-R DVD-RW/-R DVD+RW/+R USB device (not guaranteed) Media ® is a trademark of DVD Format/Logo Licensing Corporation. The following discs will not play back on this unit.
E3TK6BD_EN.book Page 10 Wednesday, February 17, 2010 10:18 AM Functional Overview Front Panel 1*3 2 3 4*1 5 6 PAL DUBBING VCR REC PROGRAM VCR DVD VCR VCR HDD DVD VCR HDD DVD HDD DVD SELECT HDD HDD DVD HDD/DVD USB 23 21*2 19*2 17 16 24 22 20*2 18 15 13 11 9 14 12 10*1 8 DV IN 7 You can also turn on the unit by pressing these buttons. You can turn on the unit by pressing these buttons only when a videotape is in this unit.
E3TK6BD_EN.book Page 11 Wednesday, February 17, 2010 10:18 AM 20 21 22 3 5 6 26 27 7 28 8 29 9 30 10 13 14 15 33 34 35 16 17 18 19 36 37 38 39 Note • If you turn off this unit, [OPEN\CLOSE A] on the remote control is not available. Be sure to use [A OPEN\CLOSE] or [STOP\EJECT C \ A] on the unit. VCR Functions Button names described in the Owner’s Manual The instructions in this manual are described mainly with the operations using the remote control.
E3TK6BD_EN.book Page 12 Wednesday, February 17, 2010 10:18 AM Installing Batteries in the Remote Control Install 2 R6 (1.5 V) batteries (supplied) into the remote control, carefully match with the polarity indicated inside the battery compartment. 1 2 Switching HDD / DVD / VCR mode You must select which component you want to operate first. Press [HDD], [DVD] or [VCR] on the remote control or the front panel.
E3TK6BD_EN.book Page 13 Wednesday, February 17, 2010 10:18 AM Guide to On-Screen Displays
Title name information DISPLAY Menu HDD 4ITLE .AME DVD -Y 4ITLE T 1/ 5 C (only when DVD+RW/+R, VR mode DVD-RW, unfinalised video mode DVD-RW/-R disc or HDD is in playback) File name information 8 1 -RW VR ORG 2 1 BBC1 3 1/ 5 Connections With a disc inserted into the unit, press [DISPLAY] to display the on-screen display.E3TK6BD_EN.book Page 14 Wednesday, February 17, 2010 10:18 AM Main Menu VCR While in the VCR mode, the on screen display of the VCR mode is displayed. Press [VCR] first. Press [DISPLAY] to display the on screen display. Press [SETUP] to display the main menu. Then use [K \ L] to select a menu and press [ENTER\OK] to display the sub menu. Press [RETURN\BACK] to return to previous screen. .
E3TK6BD_EN.book Page 15 Wednesday, February 17, 2010 10:18 AM G DISC Playback Mode Audio CD / video CD DISC Playback Mode C Title List 1 2 3 To call up the title list.
E3TK6BD_EN.book Page 16 Wednesday, February 17, 2010 10:18 AM Front Panel Display Guide 1 2 DTV 3 DB 4 1 DTV indicator : Appears when a videotape is in this unit. : Appears when the channel is in digital mode. : Appears when a disc is in this unit. 2 Title / Track and Chapter number : : 3 Title / track number Chapter number DB : 4 Current status of the unit Appears when playback is paused. Appears during step by step playback. B: Appears when playing back an HDD or disc.
E3TK6BD_EN.book Page 17 Wednesday, February 17, 2010 10:18 AM Connect the unit to a TV after considering the capabilities of your existing equipment. Before installation, unplug your TV and this unit. Antenna RF cable (not supplied) 1 To Aerial jack Audio IN Component video IN Y PB/CB Recording If your TV has component video input jacks, use a component video cable and an audio cable (to connect the AUDIO OUT (L\R) jacks).
E3TK6BD_EN.book Page 18 Wednesday, February 17, 2010 10:18 AM Using an HDMI Compatible Port [HDMI CONNECTION] • HDMI outputs the video / audio signals without converting to analogue signals. • No audio connections is required. • Use the HDMI cable (commercially available) for connection. • Connect the HDMI output jack of this unit to the HDMI input jack of TV.
E3TK6BD_EN.book Page 19 Wednesday, February 17, 2010 10:18 AM Recording from a DVD player, Satellite Box or other Audio-Video equipment with a Scart output socket (AV2) Digital Audio for Better Sound Quality Dolby Digital decoder, DTS decoder or MPEG decoder, etc. Digital audio input jack COAXIAL Connections This unit has three input terminals. Press [INPUT SELECT F] repeatedly to select the external input mode, then press [PROG. G \ H] repeatedly to select AV1, AV2 or DV(AV3).
E3TK6BD_EN.book Page 20 Wednesday, February 17, 2010 10:18 AM Basic Setup / TV View Operation Initial Setting When you turn on this unit for the first time, you need to follow these steps. 1 2 Press [B ON\STANDBY]. 3 Select your desired tuning type according to your area using [K \ L], then press [ENTER\OK]. Turn the TV on. Select the input to which the unit is connected. Also you can customize the memorised channel at “General Setting”. Refer to following pages for details.
E3TK6BD_EN.book Wednesday, February 17, 2010 10:18 AM Select “Auto Tuning (DVB & ANALOG)” using [K \ L], then press [ENTER\OK]. The unit will start storing channels available in your area. General Setting Auto Tuning (DVB & ANALOG) DVB Channel Setup ANALOG Channel Setup ANALOG You can preset an analogue channel manually and individually. In stop mode, press [SETUP]. Select “General Setting” using [K \ L], then press [ENTER\OK]. 2 Select “Channel” using [K \ L], then press [ENTER\OK].
E3TK6BD_EN.book Page 22 Wednesday, February 17, 2010 10:18 AM The tuner scans and memorises all the active DVB channels (TV / Radio) in your area. Skip a Preset Channel ANALOG Channel Search S.No. TV Channel You can set the unit to skip channels. You can no longer receive or watch when you access channels using [PROG. G \ H]. 1 Follow steps 1 to 4 in “Manual Tuning (ANALOG)” on page 21. 2 3 Select “Position” using [K \ L], then press [1].
E3TK6BD_EN.book Page 23 Wednesday, February 17, 2010 10:18 AM TV View Operation DVB The following operations are available while viewing TV channels through this unit’s tuner. 1 Select a Channel ANALOG • “Quick Select” menu will appear. To switch DVB, analogue and external input (AV1/AV2/ DV(AV3)) mode. Press [INPUT SELECT F] repeatedly to select DVB, analogue or external input mode. The mode changes as follows: Analogue mode Quick Select Group: All S.No.
E3TK6BD_EN.book Page 24 Wednesday, February 17, 2010 10:18 AM Edit Channels Edit Group Lists DVB DVB With “Edit Channels” menu, you can sort all the memorised DVB channels into the group lists (“Quick Select”) or set the viewer limitation (“Adult Lock”), etc. 1 2 In stop mode, press [SETUP]. Select “General Setting” using [K \ L], then press [ENTER\OK]. Select “Channel” using [K \ L], then press [ENTER\OK]. 3 Select “DVB Channel Setup” using [K \ L], then press [ENTER\OK].
E3TK6BD_EN.book Page 25 Wednesday, February 17, 2010 10:18 AM Channel Move DVB DVB You can set the unit to limit the access to the DVB channels. 1 Select the DVB channel you want to limit the access using [K \ L], then press [YELLOW]. Edit Channels S.No. Channel Name 5 Fav. Skip Lock Del. Five Follow steps 1 to 4 in “Edit Channels” on page 24. 2 Select the DVB channel you want to change the position using [K \ L], then press [ENTER\OK]. Pop up window will appear.
E3TK6BD_EN.book Page 26 Wednesday, February 17, 2010 10:18 AM Signal Information Multi Audio DVB DVB You can check the detailed information of the current DVB channel. 1 2 Follow steps 1 to 3 in “Auto Tuning (DVB)” on page 22. Many DVB channels transmit Multi Audio information along with their DVB channels. You can select the desired audio mode and audio language. 1 Select “Signal Information” using [K \ L], then press [ENTER\OK]. While viewing a DVB programme, press [AUDIO D].
E3TK6BD_EN.book Page 27 Wednesday, February 17, 2010 10:18 AM • If the programme is changed, the subtitle language will be switched back to the default language you set in the “DVB Setting”. Refer to “B Language” on page 73. If the default subtitle language is not available on the new programme, no subtitle will be displayed. 1 2 DVB While viewing a DVB programme, press [AD].
E3TK6BD_EN.book Page 28 Wednesday, February 17, 2010 10:18 AM 38 Recording Restrictions on Recording Information on DVD Recording Type of Discs This unit can record on DVD-RW/-R discs and DVD+RW/+R discs. DVD-R/+R discs allow you to record programmes only once, and the recorded contents can be erased although the space left on the disc does not change. DVD-RW/+RW discs allow you to record programmes repeatedly, and the recorded contents can be erased.
E3TK6BD_EN.book Page 29 Wednesday, February 17, 2010 10:18 AM Introduction Making Discs Playable in Other DVD Players (Finalise) After recording, you must finalise the disc to play it back in other players. (See page 45.) You cannot finalise discs in other DVD recorders. Disc Type DVD-R DVD-RW Video Mode VR Mode DVD+RW DVD+R ✔ ✔ After finalising ✔ Undo finalising (See page 45.) Additional recording or editing (See page 45.
E3TK6BD_EN.book Page 30 Wednesday, February 17, 2010 10:18 AM Make Recording Compatible Formatting a Disc Choosing the Recording Format of a Blank DVD-RW Disc Video VR DVD-RW DVD-RW When inserting a brand-new DVD-RW/+RW disc, the unit automatically starts to initialise the disc. DVD+RW disc will always be formatted in +VR mode, and DVD-RW disc will be formatted either video or VR mode according to the recording format mode setting of the unit.
E3TK6BD_EN.book Page 31 Wednesday, February 17, 2010 10:18 AM HDD Video VR DVD-RW DVD-RW 2 Select “Recording” using [K \ L], then press [ENTER\OK]. 3 Select “Auto Chapter” using [K \ L], then press [ENTER\OK]. 4 If you want to set “Auto Chapter” off, select “OFF” using [K \ L], then press [ENTER\OK]. !UTO #HAPTER If you want to change the time period for “Auto Chapter”, select the required time period using [K \ L], then press [ENTER\OK].
E3TK6BD_EN.book Page 32 Wednesday, February 17, 2010 10:18 AM Setting Bilingual Recording Audio Video DVD-RW DVD-R DVD+RW DVD+R You can select either “Main” or “Sub” audio to record a bilingual broadcast in video mode or +VR mode. This setting is only for recording analogue channel. 1 In stop mode, press [SETUP]. Select “General Setting” using [K \ L], then press [ENTER\OK]. 2 Select “Recording” using [K \ L], then press [ENTER\OK].
E3TK6BD_EN.book Page 33 Wednesday, February 17, 2010 10:18 AM 8 Introduction • When the unit reaches the specified time, it will be turned off automatically. • To change the recording length during One-touch Timer Recording, press [REC I] repeatedly until the desired length appears. • To cancel One-touch Timer Recording within the specified time, press [STOP C]. Timer Recording DVB HDD ANALOG Video VR DVD-RW DVD-RW DVD-R Press [STOP C] to stop the recording. Note Insert a recordable disc.
E3TK6BD_EN.book Page 34 Wednesday, February 17, 2010 10:18 AM 5 Select the digital (DVB) / analogue (ATV) mode or external input (AV1/AV2) using [K \ L], then press [1]. 6 Select the channel number to record using [K \ L], then press [1]. 7 Select the recording media (“HDD” or “DVD”) using [K \ L], then press [1]. 8 Select the recording mode using [K \ L], then press [1]. Refer to “Recording Mode” on page 28. 9 For DVB channel recording: Select “STTL” to “ON” or “OFF” using [K \ L].
E3TK6BD_EN.book Page 35 Wednesday, February 17, 2010 10:18 AM In stop mode, press [TIMER PROG.]. E41 Power failure Select the periodical timer recording programme you want to skip using [K \ L], then press [ENTER\OK]. E42 No disc E43 Already 49 titles recorded (+VR mode) E44 Already 254 chapters recorded (+VR mode) E45 Copy prohibited programme E46 It is impossible to record additionally on a disc recorded by other units when setting “Make Recording Compatible” to “OFF”.
E3TK6BD_EN.book Page 36 Wednesday, February 17, 2010 10:18 AM Priority of overlapped settings The unit records programmes according to priority if the timer programmes overlap. If the starting time is same: • The timer programming set first (PROG. 1) has priority. PROG. 1 PROG. 2 recording will start after PROG. 1 recording is completed. PROG. 1 PROG. 2 Actual recording If the End time of the programme currently being recorded and the Start time of the subsequent programme are same: • If PROG.
E3TK6BD_EN.book Page 37 Wednesday, February 17, 2010 10:18 AM HDD Video VR DVD-RW DVD-RW DVD-R 1 While viewing a DVB programme, press [GUIDE]. 2 Select a desired programme using [K \ L \ 0 \ 1], then press [YELLOW]. • Other series of the TV programme and recommended programme related to the TV programme will be displayed in “Series List”. 3 Press [BLUE] or [ENTER\OK]. Series List 13:12 Mon 17/05 S.No.
E3TK6BD_EN.book 2 Page 38 Wednesday, February 17, 2010 10:18 AM Press [SAT.LINK]. • “Sat” will appear on the front panel display and the unit goes into the satellite link standby mode. Settings for External Equipment Video Colour System To cancel the satellite link function in the satellite link standby mode: Press [B ON\STANDBY] or [SAT.LINK] to turn on the unit. To cancel the satellite link function while the satellite link recording is in progress: On the front panel Press [STOP C].
E3TK6BD_EN.book Wednesday, February 17, 2010 10:18 AM Press [STOP C] (HDD/DVD) or [STOP\EJECT C \ A] (VCR) on the unit to stop recording. Note The following instructions are described with the operations using the remote control of this unit. 1 2 • With “Control” highlighted, press [ENTER\OK] to display the available devices to control with the remote control of this unit. Select the device you want to operate using [K \ L], then press [ENTER\OK].
E3TK6BD_EN.book Page 40 Wednesday, February 17, 2010 10:18 AM To stop dubbing: DVC to HDD / DVD Dubbing HDD Video VR DVD-RW DVD-RW DVD-R DVD+RW DVD+R Before recording from DVC, see page 19 for connection instructions. (See page 75 for DVC to VCR Dubbing.) Preparing for DV dubbing (DVC to HDD): • Make sure your DVC is in video mode. Preparing for DV dubbing (DVC to DVD): • Insert a recordable DVD. • Make sure your DVC is in video mode. If you want to record to the HDD, press [HDD] first.
E3TK6BD_EN.
E3TK6BD_EN.book Page 42 Wednesday, February 17, 2010 10:18 AM VCR to HDD / DVD You can copy the contents of a videotape to HDD or DVD disc. Limitation: • If a copy control signal is detected during dubbing, the dubbing will be stopped. • Copy-once programmes which are recorded directly from the TV can be dubbed to the HDD and CPRM compatible VR mode DVD-RW. • Copy-once programmes which are copied from the HDD / DVD to a videotape cannot be dubbed further from the videotape to the HDD / DVD.
E3TK6BD_EN.book Page 43 Wednesday, February 17, 2010 10:18 AM HDD Video VR DVD-RW DVD-RW HDD to DVD / DVD to HDD / HDD to VCR / DVD to VCR 3 DVD-R e.g.) HDD A DVD DVD+RW DVD+R This function lets you select one specific title from the title list for dubbing. HDD DVD HDD VCR DVD VCR 3 Select “Dubbing” using [K \ L], then press [ENTER\OK]. Select a desired title to be dubbed using [K \ L \ 0 \ 1], then press [ENTER\OK]. 4 Select “Add” using [K \ L], then press [ENTER\OK]. HDD e.g.
E3TK6BD_EN.book Page 44 Wednesday, February 17, 2010 10:18 AM To move a title: 1) Go to the dubbing list, then select a title using [K \ L]. Then press [ENTER\OK]. 2) Select “Move” using [K \ L], then press [ENTER\OK]. 3) Select a desired insert point using [K \ L], then press [ENTER\OK]. VCR to HDD / DVD 3 Select “VCR A HDD” / “VCR A DVD” using [K \ L], then press [ENTER\OK]. e.g.
E3TK6BD_EN.book Wednesday, February 17, 2010 10:18 AM Select “Yes” using [K \ L], then press [ENTER\OK]. The disc is protected. 5 Press [SETUP] to exit. Note Video VR Insert a recordable disc before finalising. 1 In stop mode, press [SETUP]. Auto Finalise Video DVD-RW DVD-R DVD+R You can finalise discs automatically when the disc space runs out if you set this in “Setup” menu. Select “DVD Menu” using [K \ L], then press [ENTER\OK]. 1 3 Select “Finalise” using [K \ L], then press [ENTER\OK].
E3TK6BD_EN.book Page 46 Wednesday, February 17, 2010 10:18 AM Playback 8 To eject the disc, press [OPEN\CLOSE A] to open the disc tray, then remove the disc. Press [OPEN\CLOSE A] to close the disc tray before turning off the unit. Basic Playback Note for HDD / DVD Playback Note The contents of an HDD / DVD are generally divided into titles. Titles are further subdivided into chapters depend on Auto Chapter setting (See page 31). Start Rec. Press [STOP C] to stop playback. Stop Rec./Start Rec.
E3TK6BD_EN.book Page 47 Wednesday, February 17, 2010 10:18 AM CD MP3 JPEG DivX ® 2 If you want to play back an audio CD or a disc with a single file type (e.g, a disc containing MP3 files only), skip to step 4. If you want to play back a disc with mixed file types, proceed to step 3. 3 Select the desired file type using [K \ L], then press [ENTER\OK]. 4 Press [K \ L] to select the desired track / file or folder, then press [ENTER\OK]. e.g.
E3TK6BD_EN.book Page 48 Wednesday, February 17, 2010 10:18 AM Playing Back a USB Device with MP3 / JPEG / DivX® Files 2 If you want to change the media type, press [0]. Select the desired media type using [K \ L], then press [ENTER\OK]. (You can also access the media type selection screen from the “Title List” in the “Setup” menu in stop mode.) • Video Files: The DivX® File List will appear (not guaranteed). • Music: The MP3 File List will appear. • Photo: The JPEG File List will appear.
E3TK6BD_EN.book Page 49 Wednesday, February 17, 2010 10:18 AM DivX ® 1 2 3 Use [0 \ 1] to select “Yes” if you want to play back the file, or to select “No” if you do not want to play it back. Then press [ENTER\OK] to confirm the selection. • You cannot play back the DivX® VOD files of which rental period has been expired. In such case, press [TOP MENU] and select other files that can be played back. DivX® VOD DivX Subtitle Rental Expired DivX® VOD selection screen will appear.
E3TK6BD_EN.book Page 50 Wednesday, February 17, 2010 10:18 AM • If DivX® files written on CD discs cannot be played back, rewrite them on a DVD disc and try to play back. • For more information for DivX®, please visit http://www.divx.com. • You cannot play back the DivX® VOD files obtained with different registration codes on this unit. Press [TOP MENU] and select other files that can be played back. • This unit does not support the DivX® file with UDF format.
E3TK6BD_EN.book Page 51 Wednesday, February 17, 2010 10:18 AM Fast Forward / Fast Reverse HDD VCD DVD+RW (PBC OFF) 1 2 Select “DISC Playback Mode” using [K \ L], then press [ENTER\OK]. 3 Select “PBC (Video CD only)” using [K \ L], then press [ENTER\OK]. 5 Press [SETUP] to exit.
E3TK6BD_EN.book Page 52 Wednesday, February 17, 2010 10:18 AM Step by Step Playback HDD DVD-V DVD+RW 1 2 Zoom Video VR DVD-RW DVD-RW HDD DVD-R VCD DivX ® DVD+R DVD+RW During playback, press [PAUSE F]. Press [SKIP H \ G] repeatedly. Each time you press [SKIP G], playback will go forward one frame (or step) at a time with the sound muted. To go backward one frame (or step), press [SKIP H].
E3TK6BD_EN.book Page 53 Wednesday, February 17, 2010 10:18 AM 1 During recording, press [PLAY B]. Playback of the title you are recording will start from the beginning. • Elapsed playback time will be displayed on the front panel display. 2 To stop the playback, press [STOP C] once. To playback a title being recorded while continuing to record, refer to “Chasing Playback during Recording” on this page (available only with HDD).
E3TK6BD_EN.book Page 54 Wednesday, February 17, 2010 10:18 AM Track Search Search CD DVD+RW DVD-V Video VR DVD-RW DVD-RW DVD-R DVD+R Using [SKIP H \ G] buttons 1 During playback, press [SKIP G] to skip the current track and move to the next. The unit moves to the next track one after another. To go back to the previous track, press [SKIP H] twice in quick successions. The unit moves backward one track at a time.
E3TK6BD_EN.book Page 55 Wednesday, February 17, 2010 10:18 AM HDD DVD+RW DVD-V Video VR DVD-RW DVD-RW DVD+R DVD-R VCD DivX ® CD (PBC OFF) 2 During playback, press [DISPLAY] to bring up the display menu. If the display menu is already shown, skip to step 2. Select the icon using [0 \ 1], then press [ENTER\OK]. Track: The current track will be played back repeatedly. (audio CD, video CD, MP3, JPEG and DivX® only) 3 4 Press [0 \ 1] to highlight .
E3TK6BD_EN.book Page 56 Wednesday, February 17, 2010 10:18 AM Programme Playback Selecting the Format of Audio and Video VCD CD (PBC OFF) You can programme the disc to play back in your desired order. 1 Follow steps 1 to 2 in “Random Playback” on page 55. 2 Select “Programme Play” using [K \ L], then press [ENTER\OK]. 3 Select the desired track using [K \ L], then press [ENTER\OK] or [1].
E3TK6BD_EN.book Wednesday, February 17, 2010 10:18 AM Select a desired audio soundtrack or audio channel using [K \ L], then press [ENTER\OK]. Note DVD-V HDD Video VR DVD-RW DVD-RW 1 2 Virtual Surround menu will appear. 3 Select “OFF”, “Type 1” or “Type 2” using [K \ L], then press [ENTER\OK]. e.g.) DVD-video 1/ 5 C 1/ 5 Select the icon using [0 \ 1], then press [ENTER\OK]. The angle will switch each time you press [ENTER\OK].
E3TK6BD_EN.book Page 58 Wednesday, February 17, 2010 10:18 AM Editing 1 2 Guide to a Title List Title list allows you to check the titles recorded on the disc easily. You can choose a title to play back from this list and easily edit the titles as you prefer. Press [HDD] or [DVD], then press [TOP MENU]. 2 1 6 ORG Title List ABCDE 11:00 (10:00:00) 17/05/10 125 SP 1 2 3 4 5 6 1/6 3 4 5 4 Title name.
E3TK6BD_EN.book Page 59 Wednesday, February 17, 2010 10:18 AM Editing Discs HDD : Available to edit in the HDD Original Original VR DVD-RW Note • It is not possible to retrieve deleted titles. If you want to edit the HDD, press [HDD] first. If you want to edit a disc, press [DVD] first. 1 Title List will appear. For HDD and VR mode DVD-RW disc, press [DISC MENU] to switch between “Original” and “Playlist”. 2 3 Playlist e.g.
E3TK6BD_EN.book Page 60 Wednesday, February 17, 2010 10:18 AM 5 Deleting Selected Titles To enter the title name, refer to “Guide to Editing Title Names” on this page. ORG HDD Edit Edit Title Name You can delete titles which you do not need anymore. Please be advised that the titles once deleted cannot be brought back. 1 2 3 Select the title you want to delete using [K \ L \ 0 \ 1], then press [ENTER\OK]. 6 C c 3 ? 0:00:59 When you finish entering the title name, press [ENTER\OK].
E3TK6BD_EN.book Page 61 Wednesday, February 17, 2010 10:18 AM Adding or Deleting Chapter Marks at once for Video Mode DVD-RW disc VR HDD DVD-RW Video DVD+RW DVD+R You can add chapter marks to a title. After a title is marked with chapters, you can use the chapter search feature. You can set a chapter mark anywhere you want. Press [DVD] first. Follow the steps 1 to 3 in “Editing Title Name” on page 60. 1 2 Select “Chapter Mark” using [K \ L], then press [ENTER\OK].
E3TK6BD_EN.book Page 62 Wednesday, February 17, 2010 10:18 AM Hiding Chapters Dividing a Title VR DVD+RW DVD+R You can hide chapters from the title list. Hidden chapters are skipped during playback. Press [DVD] first. 1 Follow the steps 1 to 3 in “Editing Title Name” on page 60. 2 Select “Hide Chapter” using [K \ L], then press [ENTER\OK]. 3 Use [SKIP H \ G], [PLAY B] and [PAUSE F] to decide the chapter to be hidden.
E3TK6BD_EN.book Page 63 Wednesday, February 17, 2010 10:18 AM Note • To delete a title from the Playlist, refer to “Deleting Titles” on page 59. • When the number of the Playlist reaches its maximum (refer to page 29), or when the number of the total chapter marks of the Playlists reaches 999 (only for VR mode DVD-RW), “Add To Playlist” cannot be selected. VR DVD-RW HDD Playlist Playlist You can combine two titles into a single title.
E3TK6BD_EN.book Page 64 Wednesday, February 17, 2010 10:18 AM Deleting Parts of Titles VR HDD DVD-RW You can delete a specific part of a title. Even when a title is deleted from the Playlist, the original title will remain as it is. If you edit the HDD, press [HDD] first. If you edit a disc, press [DVD] first. 1 Follow the steps 1 to 3 in “Editing Title Name” on page 60. 2 Select “Scene Delete” using [K \ L], then press [ENTER\OK].
E3TK6BD_EN.book Page 65 Wednesday, February 17, 2010 10:18 AM Introduction Function Setup The following table is the contents which you can set and the default settings. Refer to the following table for useful operation. Items (highlight is the default) Parental Lock E Page 68 Audio Out Dynamic E Pages 68-69 Range Control PCM MPEG 48kHz 96kHz PCM Stream PCM Stream Set whether the sound recorded in 96kHz will be down sampled to 48kHz.
E3TK6BD_EN.book Setup Recording Page 66 Wednesday, February 17, 2010 Items (highlight is the default) Auto Chapter E Page 31 Recording Audio Select (XP) E Page 32 Auto Finalise E Page 45 Aspect Ratio (Video mode) E Page 30 Make Recording Compatible E Page 30 Bilingual Recording Audio E Page 32 External Input Audio E Page 31 Video Colour System E Page 38 10:18 AM Contents Insert chapter marks periodically.
E3TK6BD_EN.book Page 67 Contents Set the colour space for the HDMI output. RGB YCbCr ON OFF Set whether to output the HDMI audio signal or not. Normal Enhanced ON OFF English Gaelic Welsh Set the black-white contrast level for HDMI RGB output. Set the Adult Lock and change Pincode.
E3TK6BD_EN.book Page 68 Wednesday, February 17, 2010 10:18 AM Playback Setup A General Setting A Playback A password is already set 1 Enter the current password using [the Number buttons]. A B C D E F G H I Parental Lock Audio Out Disc Menu Language Audio Language Subtitle Language Angle Icon Still Mode Variable Skip/Replay TV System Password Input 2-A Select “No” using [K \ L], then press [ENTER\OK].
E3TK6BD_EN.book Page 69 Wednesday, February 17, 2010 10:18 AM PCM 48kHz 96kHz C Disc Menu Language (Default: English) (DVD only) Set “Disc Menu Language”. Disc Menu Language : If your amplifier / decoder is NOT compatible with 96 kHz PCM, select “48kHz”. Sound recorded at 96 kHz is down sampled to 48 kHz. 96kHz : If your amplifier / decoder is compatible with 96 kHz PCM, select “96kHz”. Sound is sampled at 96 kHz.
E3TK6BD_EN.book Page 70 Wednesday, February 17, 2010 10:18 AM G Still Mode (Default: Auto) (DVD only) Still Mode Auto Field Frame Auto : Automatically select the best resolution setting (“Frame” or “Field”) based on the data characteristics of the pictures. Field : Select “Field” when the pictures are still unstable even if “Auto” is selected. “Field” stabilises the pictures, although the picture quality may become coarse due to the limited amount of data.
E3TK6BD_EN.book Page 71 Wednesday, February 17, 2010 10:18 AM Introduction 2 Select “Yes” using [0 \ 1], then press Video [ENTER\OK]. Setup A General Setting A Video A TV Aspect B Video Out Final confirmation window will appear. 3 Select “Yes” using [K \ L], then press [ENTER\OK] within 15 seconds. Confirm again to use progressive scan. If picture is good, select “Yes”.
E3TK6BD_EN.book Page 72 Wednesday, February 17, 2010 10:18 AM B Auto Clock Setting (Default: ON) This unit receives time signals from the analogue / DVB channels, and set the clock automatically. Set the channel tuning before setting Auto Clock. Auto Clock Setting ON OFF HDMI Setup A General Setting A HDMI • Make sure that the HDMI cable is connected and the TV input is set to HDMI. A Format B HDMI Audio C RGB Range 1 Select “ON” using [K \ L], then press [ENTER\OK]. 2 Press [SETUP] to exit.
E3TK6BD_EN.book Page 73 Wednesday, February 17, 2010 10:18 AM Setup A General Setting A DVB Setting You can make settings of the digital tuner from the DVB Setting. A Adult Lock (Default: OFF) DVB 1 Select “ON” or “OFF” using [K \ L], then press [ENTER\OK]. Adult Lock Select “Yes” using [K \ L], then press [ENTER\OK]. Reset to factory default? Yes No “Are you sure?” will appear. Select “Yes” using [K \ L], and then press [ENTER\OK].
E3TK6BD_EN.book Page 74 Wednesday, February 17, 2010 10:18 AM VCR Functions Common Procedures 1 Press [B ON\STANDBY] to turn on the unit. To play back a tape, turn on the TV and be sure to select the input to which the unit is connected. 2 Basic Recording and One-touch Timer Recording (OTR) VCR Press [VCR].
E3TK6BD_EN.book Page 75 Wednesday, February 17, 2010 10:18 AM One-touch Timer Recording will start. 0:30 8:00 1:00 • Insert a recordable videotape. • Make sure your DVC is in video mode. Press [INPUT SELECT F] repeatedly to select the external input channel, then press [PROG. G \ H] repeatedly to select DV(AV3). 2 Select the recording mode using [REC MODE]. (See page 74.) 3 Stop or pause the DVC where you want to start dubbing. 4 5 Play back the DVC.
E3TK6BD_EN.book Page 76 Wednesday, February 17, 2010 10:18 AM Time Search VCR This feature allows you to go to a specific point on a tape by entering the exact amount of time you want to skip in order to reach the point. 1 Press [SEARCH] repeatedly until the time search menu appears. 2 Enter your desired time to skip using [the Number buttons] within 30 seconds. 3 Press [FWD D] or [REV E] to start time search. If you want to go in the forward direction, press [FWD D].
E3TK6BD_EN.book Page 77 Wednesday, February 17, 2010 10:18 AM Introduction Others Before requesting service for this unit, check the table below for a possible cause of the problem you are experiencing. Some simple checks or a minor adjustment on your part may eliminate the problem and restore proper operation. The unit turns on automatically without any operation. • The unit turns on automatically 2 seconds before the timer recording. The unit does not function.
E3TK6BD_EN.book Page 78 Wednesday, February 17, 2010 Symptom Remedy TV channels cannot be changed. CHANNEL 10:18 AM • Check if the connections are made securely and correctly. • Check if the cables are damaged. • Try “Channel” setting by following the steps on pages 20-22. Some settings are lost even though you • If you unplug the AC mains cable while the warning message, “Saving settings. followed the procedure correctly. Please wait.”, is displayed, some settings may be lost.
E3TK6BD_EN.book Page 79 Wednesday, February 17, 2010 10:18 AM Remedy • Check if the playable disc is inserted. • Check if the disc is loaded correctly with the labelled side facing up. • Discs made on other devices or on personal computers cannot be played back on this unit unless it is finalised on the device. • Even if it is finalised, the performance of those discs are not guaranteed on this unit. • The disc may be dirty or flawed. Clean the disc. • Check if all the connections are made correctly.
DVD EDITING HDD / DVD E3TK6BD_EN.book Page 80 Wednesday, February 17, 2010 Symptom Remedy Titles cannot be edited or deleted. • The titles or the disc itself may be protected. Cancel the protection by following the steps on page 62 for title protection and page 44 for disc protection. Dubbing cannot be executed. • When the number of the titles or the chapters exceeds the maximum recordable number, the dubbing will not be executed. Titles cannot be edited or deleted.
E3TK6BD_EN.book Page 81 Wednesday, February 17, 2010 Cause Introduction Error message 10:18 AM Solution • Insert a recordable disc with enough recording space. • Delete unnecessary original titles. (See page 59.) Recording Error You cannot record more than 99 titles on one disc. (The maximum is 99) • You are trying to record onto the DVD-RW / -R disc on which the number of recorded titles has reached the maximum (99). • Delete unnecessary original titles. (See page 59.
E3TK6BD_EN.
E3TK6BD_EN.book Page 83 Wednesday, February 17, 2010 10:18 AM Introduction Specifications General VCR video heads Four heads HDD Internal 3.5 inch HDD 320 GB 220–240 V Power consumption 48 W Power consumption (standby) 0.93 W Weight 5.8 kg ± 10 %, 50 Hz ± 0.5 % 435 x 99.
E3TK6BD_EN.