TOSHIBA Satellite 2450 Series Portable Personal Computer User’s Manual
Copyright © 2003 by TOSHIBA Corporation. All rights reserved. Under the copyright laws, this manual cannot be reproduced in any form without the prior written permission of TOSHIBA. No patent liability is assumed, with respect to the use of the information contained herein.
iLINK is a trademark and Memory Stick is a registered trademark of Sony Corporation. Compact Flash is a trademark of SunDisk Corporation. FCC information Product Name : Satellite 2450 Model number : PS245 FCC notice "Declaration of Conformity Information" This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
FCC conditions This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: 1. This device may not cause harmful interference. 2. This device must accept any interference received, including interference that may cause undesired operation. Contact Address: TOSHIBA America Information Systems, Inc.
Modem warning notice Conformity Statement The equipment has been approved to [Commission Decision “CTR21”] for panEuropean single terminal connection to the Public Switched Telephone Network (PSTN). However, due to differences between the individual PSTNs provided in different countries/regions the approval does not, of itself, give an unconditional assurance of successful operation on every PSTN network termination point.
Japan regulations Region selection If you are using the computer in Japan, technical regulations described in the Telecommunications Business Law require that you select the Japan region mode. It is illegal to use the modem in Japan with any other selection. Redial Up to two redial attempts can be made. If more than two redial attempts are made, the modem will return Black Listed. If you are experiencing problems with the Black Listed code, set the interval between redials at one minute or longer.
Telephone company procedures The goal of the telephone company is to provide you with the best service it can. In order to do this, it may occasionally be necessary for them to make changes in their equipment, operations, or procedures. If these changes might affect your service or the operation of your equipment, the telephone company will give you notice in writing to allow you to make any changes necessary to maintain uninterrupted service.
Instructions for IC CS-03 certified equipment 1 The Industry Canada label identifies certified equipment. This certification means that the equipment meets certain telecommunications network protective, operational and safety requirements as prescribed in the appropriate Terminal Equipment Technical Requirements document(s). The Department does not guarantee the equipment will operate to the user’s satisfaction.
3 The standard connecting arrangement (telephone jack type) for this equipment is jack type(s): USOC RJ11C. The IC registration number of the modem is shown below. Canada: 1353A-L4AINT Notes for Users in Australia and New Zealand Modem warning notice for Australia Modems connected to the Australian telecoms network must have a valid Austel permit. This modem has been designed to specifically configure to ensure compliance with Austel standards when the country/region selection is set to Australia.
Notes for use of this device in New Zealand ❑ The grant of a Telepermit for a device in no way indicates Telecom acceptance of responsibility for the correct operation of that device under all operating conditions. In particular the higher speeds at which this modem is capable of operating depend on a specific network implementation which is only one of many ways of delivering high quality voice telephony to customers. Failure to operate should not be reported as a fault to Telecom.
ATS11=90 (DTMF dialing on/off duration=90 ms) ATX2 (Dial tone detect, but not (U.S.A.) call progress detect) ❑ When used in the Auto Answer mode, the S0 register must be set with a value of 3 or 4. This ensures: (a) a person calling your modem will hear a short burst of ringing before the modem answers. This confirms that the call has been successfully switched through the network. (b) caller identification information (which occurs between the first and second ring cadences) is not destroyed.
General conditions As required by PTC 100, please ensure that this office is advised of any changes to the specifications of these products which might affect compliance with the relevant PTC Specifications. The grant of this Telepermit is specific to the above products with the marketing description as stated on the Telepermit label artwork. The Telepermit may not be assigned to other parties or other products without Telecom approval.
Description on Laser specification The optical drive such as CD-ROM drive, CD-RW drive, DVD-ROM drive, DVD/ CD-RW drive and DVD Multi drive that is used in this computer is equipped with laser. The classification label with the following sentence is affixed to the surface of the drive.
Table of Contents Preface Manual contents ............................................................................. xxiii Conventions ..................................................................................... xxiv Abbreviations ..................................................................................... xxiv Icons ................................................................................................. xxiv Keys ................................................................
Underside ........................................................................................... 2-7 Front with the display open .............................................................. 2-8 System indicators ............................................................................ 2-10 Keyboard indicators ........................................................................ 2-11 USB diskette drive ...........................................................................
Changing Lifestyle Bay modules ..................................................... 4-3 Removing a module ............................................................................ 4-3 Installing a module .............................................................................. 4-4 Using optical media drives ............................................................... 4-5 Loading disks ..................................................................................... 4-5 Removing disks .......
Chapter 5 The Keyboard Typewriter keys ................................................................................. 5-1 F1 … F12 function keys ..................................................................... 5-2 Soft keys: Fn key combinations ........................................................ 5-2 Emulating keys on enhanced keyboard .............................................. 5-2 Hot keys .............................................................................................
Panel power off ............................................................................... 6-15 System Auto Off ............................................................................... 6-15 Chapter 7 HW Setup and Passwords HW Setup ........................................................................................... 7-1 Accessing HW Setup ......................................................................... 7-1 HW Setup window ..........................................................
Chapter 9 Troubleshooting Problem solving process ................................................................... 9-1 Preliminary checklist .......................................................................... 9-1 Analyzing the problem ........................................................................ 9-2 Hardware and system checklist ........................................................ 9-3 System start-up ..................................................................................
Appendixes Appendix A Specifications ................................................................................... A-1 Appendix B Display Controller and Modes ......................................................... B-1 Appendix C AT Commands .................................................................................. C-1 Appendix D S-registers ......................................................................................... D-1 Appendix E V.90 ..........................................
xxii
Preface Congratulations on your purchase of the Satellite 2450 series computer. This powerful notebook computer provides excellent expansion capability, including multimedia devices, and it is designed to provide years of reliable, high-performance computing. This manual tells how to set up and begin using your Satellite 2450 series computer. It also provides detailed information on configuring your computer, basic operations and care, using optional devices and troubleshooting.
User's Manual Chapter 4, Operating Basics, includes instructions on using the following devices: Touch Pad, Slim Select Bay modules, USB diskette drive, optical media drives, audio/video controls, microphone, modem, wireless communication features, LAN. It also provides tips on care of the computer, diskettes and CD/DVDs. Chapter 5, The Keyboard, describes special keyboard functions including the keypad overlay and hot keys.
Conventions Key operation Some operations require you to simultaneously use two or more keys. We identify such operations by the key top symbols separated by a plus sign (+). For example, Ctrl + C means you must hold down Ctrl and at the same time press C. If three keys are used, hold down the first two and at the same time press the third.
User's Manual xxvi
General Precautions TOSHIBA computers are designed to optimize safety, minimize strain and withstand the rigors of portability. However, certain precautions should be observed to further reduce the risk of personal injury or damage to the computer. Be certain to read the general precautions below and to note the cautions included in the text of the manual. Stress injury Carefully read the Instruction Manual for Safety & Comfort.
User's Manual Central Processing Unit ("CPU") Performance Disclaimer CPU Performance in your computer product may vary from specifications under the following conditions: use of certain peripheral products use of battery power instead of AC power use of certain multimedia games or videos with special effects use of complex modeling software, such as high end computer aided design application use of computer in areas with low air puressure (high altitude >1,000 meters or >3,280 feet above sea level) use of
Introduction This chapter provides an equipment checklist, and it identifies the computer’s features, options and accessories. CAUTION: Some of the features described in this manual may not function properly if you use an operating system that was not preinstalled by TOSHIBA. Equipment checklist Carefully unpack your computer. Save the box and packing materials for future use.
INTRODUCTION User's Manual • • • • ❑ TOSHIBA Power Saver TOSHIBA Console Infrared Device Driver Online manual Product Recovery CD-ROM Documentation • • • • Satellite 2450 Portable Personal Computer User's Manual Microsoft Windows XP manual package Instruction Manual for Safety & Comfort End User License Agreement Features The computer uses TOSHIBA’s advanced Large Scale Integration (LSI), Complementary Metal-Oxide Semiconductor (CMOS) technology extensively to provide compact size, minimum weight, low
Features Universal AC adaptor The computer has an internal battery to back up the internal Real Time Clock (RTC) and calendar. The universal AC adaptor provides power to the system and recharges the batteries when they are low. It comes with a detachable power cord. Because it is universal, it can receive a range of AC voltage from 100 to 240 volts; however, the output current varies among different models. Using the wrong model can damage your computer.
INTRODUCTION User's Manual CD-RW/DVD-ROM drive Some models are equipped with a full-size, CD-RW/DVDROM drive module that lets you run CD/DVDs without using an adaptor. It reads DVD-ROMs at maximum 8 speed and CD-ROMs at maximum 24 speed. It writes CD-R at up to 24 speed and CD-RW at up to 10 speed. A Mode Control button turns power to the fixed CD-RW/DVDROM drive on and off so you can use the drive as a standalone audio CD player. See Chapter 4, Operating Basics, for details.
Features The computer’s LCD panel supports high-resolution video graphics. The screen can be set at a wide range of viewing angles for maximum comfort and readability. Built-in Graphics controller 15.0" TFT screen, 16 M colors, with one of the following resolutions: • XGA, 1024 horizontal x 768 vertical pixels • SXGA+, 1400 horizontal x 1050 vertical pixels A 128-bit graphics controller maximizes display performance. Refer to Appendix B for more information.
INTRODUCTION User's Manual Slots PC card The PC card slot accommodates two 5 mm Type II cards or one Type III card. SD card This slot lets you easily transfer data from devices, such as digital cameras and Personal Digital Assistants, that use SD card flash-memory. You can use memory module in this slot. Multimedia Sound system Windows sound system compatible sound system provides internal speakersas well as jacks for an external microphone and headphone.
Features Modem LAN Bluetooth Wireless LAN An internal modem provides capability for data and fax communication. It supports V.90 (V.92). Refer to Appendix E. The speed of data transfer and fax depends on analog telephone line conditions. It has a modem jack for connecting to a telephone line. It is preinstalled as a standard device in some markets. Both of V.90 and V.92 are supported only in USA and Canada. Only V.90 is available in other regions.
INTRODUCTION User's Manual Software Standard Plug and Play Windows XP operating system and TOSHIBA Utilities and drivers preinstalled on the hard disk. When you connect an external device to the computer, Plug and Play capability enables the system to recognize the connection and make the necessary configurations automatically. Special features The following features are either unique to TOSHIBA computers or are advanced features, which make the computer more convenient to use.
Special features A ten-key pad is integrated into the keyboard. Refer to the Keypad overlay section in Chapter 5, Keyboard, for instructions on using the keypad overlay. Power on password Two levels of password security, supervisor and user, are available to prevent unauthorized access to your computer. Instant security A hot key function blanks the screen and disables the computer providing data security.
INTRODUCTION User's Manual Standby If you have to interrupt your work, you can turn off the power without exiting from your software. Data is maintained in the computer’s main memory. When you turn on the power again, you can continue working right where you left off. Utilities This section describes preinstalled utilities and tells how to start them. For details on operations, refer to each utility’s online manual, help files or read.me files.
Options ConfigFree is a suite of utilities to allow easy control of communication device and network connections. ConfigFree also allows you to find communication probrems and create profiles for easy switching between location and communication networks. You can boot ConfigFree from the menu bar as follows. [Start] - [All Programs] - [TOSHIBA ConfigFree] - [ConfigFree] Bluetooth TOSHIBA Stack This software enables communication between remote Bluetooth devices. Refer to the Quick Start Guide.
INTRODUCTION User's Manual Security lock A slot is available to attach a security cable to the computer to deter theft. USB FDD Kit A 3 1/2" diskette drive accommodates 1.44-megabyte or 720-kilobyte diskette. It connects to a USB port. (You cannot format 720-kilobyte diskettes on Windows XP, but you can use previously formatted disks.) Wireless LAN Kit This option enbles wireless LAN functions in computers that do not have wireless preinstalled. It is installed by dealers only.
Chapter 2 The Grand Tour Front with the display closed Figure 2-1 shows the computer’s front with its display panel in the closed position. MODE AUDIO/VIDEO AUDIO/VIDEO VOLUME CONTROL CONTROL DISPLAY LATCH CONTROL CONTROL BUTTON BUTTONS BUTTONS SYSTEM INDICATORS Figure 2-1 Front of the computer with display closed Audio/Video control buttons Previous button: Plays the previous track/chapter/ data. Play/pause button: Begins or pauses play. Stop button: Halts play.
User's Manual Display latch Volume control THE GRAND TOUR System indicators This latch secures the LCD panel in its closed position. Slide the latch to open the display. Use this dial to adjust the volume of the stereo speakers and subwoofer or the stereo headphones. LEDs let you monitor the status of various computer functions. Details are given in the Indicators section. Left side Figure 2-2 shows the computer’s left side.
Left side Cooling vents These vents provide an outlet for air pulled through the computer by the fan. CAUTION: Be careful not to block the cooling vents. Also be careful to keep foreign objects out of them. A pin or similar object can damage the computer’s circuitry. CB A PC card slot can accommodate two 5 mm Type IIcards or one Type III card. You can install any industry standard PC card such as a SCSI adaptor, Ethernet adaptor or flash memory card.
User's Manual Right side THE GRAND TOUR Figure 2-3 shows the computer’s right side. SD CARD SLOT SD CARD INDICATOR HEADPHONE JACK MICROPHONE JACK MODEM JACK SLIM SELECT BAY LINE-IN JACK Figure 2-3 The right side of the computer SD card slot SD cards are used in a wide variety of external devices. This slot lets you transfer data from the device to your computer. An indicator on the right side of the slot glows when a card is being accessed. CAUTION: Keep foreign objects out of the SD card slot.
Back side This jack lets you connect digital speakers or a stereo headphone (16 ohm minimum). When you connect a digital speaker or headphones, the internal speaker is automatically disabled. Microphone jack A 3.5 mm mini microphone jack enables connection of a three-conductor mini jack for monaural microphone input. Line-in jack A standard 3.5 mm mini line-in jack enables connection of a stereo device for audio input. Back side Figure 2-4 shows the computer’s back panel.
User's Manual Parallel port DC IN 15V THE GRAND TOUR DC IN 15V LAN jack Ether This Centronics-compatible, 25-pin parallel port is used to connect a parallel printer or other parallel device. This port supports Extended Capabilities Port (ECP) standard. The universal AC adaptor connects to this socket. Use only the model of universal AC adaptor that comes with the computer. Using the wrong adaptor can damage your computer. This jack lets you connect to a LAN.
Under side Underside Figure 2-5 shows the underside of the computer. Make sure the display is closed before turning over your computer. SLIM SELECT BAY LATCH CPU COOLING FAN WITH AIR FILTER BATTERY RELEASE LATCH Figure 2-5 The underside of the computer Slim Select Bay latch Slide this latch to free the Slim Select Bay for removal. CPU cooling fan with air filter This cooling fan intakes air to cool cpu and air filter prevents dusts from entering into the computer.
User's Manual Battery release latch Slide this latch to release the battery pack for removal. THE GRAND TOUR Front with the display open Figure 2-6 shows the front of the computer with the display open. To open the display, push the display latch on the front of the display and lift up. Position the display at a comfortable viewing angle.
Front with the display open Display screen The LCD displays high-contrast text and graphics. The computer’s LCD consists of up to 1024 x 768 pixels or 1400 x 1050 pixels. Refer to Appendix B. Internet button TOSHIBA Console button TV button Press this button to launch an Internet browser. If the computer’s power is off, you can press this button to turn on the computer’s power and launch the browser automatically in one step. Press this button to launch an application automatically.
User's Manual System indicators THE GRAND TOUR CD/DVD DIGITAL AUDIO DC IN 15V POWER BATTERY DISK SLIM SELECT BAY Figure 2-7 System indicators 2-10 CD/DVD The CD/DVD indicator glows in green when reproducing CD/DVD. This LED does not light usually and is locked not to light. Press the Mode control button for four seconds to unlock. Then CD/DVD indicator is set to light as default.
Keyboard indicators Disk Slim Select Bay The Disk indicator glows green when the computer is accessing the built-in hard disk or fixed optical media drive. Keyboard indicators The figures below show the positions of the keypad overlay indicators and the CapsLock indicator. When the F10 key indicator glows the keypad overlay lets you control the cursor. When the F11 key indicator glows the keypad overlay lets you enter numbers.
User's Manual When the CapsLock indicator glows the keyboard is in all-caps mode. CAPSLOCK THE GRAND TOUR INDICATOR Figure 2-9 CapsLock indicator Caps Lock Arrow mode Numeric mode This indicator glows green when the alphabet keys are locked in uppercase. When the Arrow mode indicator lights green, you can use the keypad overlay (gray labeled keys) as cursor keys. Refer to the Keypad overlay section in Chapter 5, The Keyboard.
Slim Select Bay modules Disk-In-Use Indicator This indicator lights when the diskette is being accessed. Diskette slot Insert diskettes in this slot. Eject button When a diskette is fully seated in the drive, the eject button pops out. To remove a diskette, push in the eject button and the diskette pops out partially for removal. NOTES: 1. The external diskette drive should be placed on a flat, horizontal surface when in use. Do not set the drive on an incline greater than 20o while it is operating.
User's Manual CD-RW/DVD-ROM drive Refer to the CD-RW/DVD-ROM drive item in the Fixed optical media drive section for details. THE GRAND TOUR NOTE: The physical features of this drive are similar to those of the DVD-ROM drive. Refer to the illustration in the DVD-ROM drive section. CAUTION: Check the Slim Select Bay indicator when you use the DVD-ROM drive or CD-RW/DVD-ROM drive in the Slim Select Bay. Do not press the eject button, disconnect a drive or turn off the computer while the light is glowing.
Slim Select Bay modules DVD Multi drive The full-size DVD Multi drive module lets you run either 12 cm (4.72") or 8 cm (3.15") CD/DVDs without using an adaptor. It reads DVD-ROMs at maximum 8 speed and CD-ROMs at maximum 24 speed. It writes CD-R at up to 16 speed, CD-RW at up to 8 speed, DVD-R and DVD-RW at single speed, and DVD-RAM at 2 speed.
User's Manual Slim Select Bay HDD adaptor (Black) You can increase your computer’s data storage capacity by installing an optional, integrated, 2 1/2" HDD in the Slim Select Bay. THE GRAND TOUR RELEASE LATCH Figure 2-12 The Slim Select Bay HDD adaptor (Black) TOSHIBA Style Bay Bridge Media Adaptor Three types of memory, a Smart Media, a Memory Stick and a Compact Flash memory can be installed and used in the Bridge media adaptor.
Universal AC adaptor Universal AC adaptor The universal AC adaptor converts AC power to DC power and reduces the voltage supplied to the computer. It can automatically adjust to any voltage from 100 to 240 volts and to a frequency of either 50 or 60 hertz, enabling you to use the computer in almost any country/region. Figure 2-14 The universal AC adaptor CAUTION: Use only the universal AC adaptor that came with the computer or an equivalent optional adaptor.
THE GRAND TOUR User's Manual 2-18
Chapter 3 Getting Started This chapter provides basic information to get you started using your computer. It covers the following topics: ❑ Setting up your work space — for your health and safety NOTE: Be sure also to read Instruction Manual for Safety & Comfort. This guide, which is included with the computer, explains product liability.
User's Manual General conditions GETTING STARTED In general, if you are comfortable, so is your computer, but read the following to make sure your work site provides a proper environment. ❑ Make sure there is adequate space around the computer for proper ventilation. ❑ Make sure the AC power cord connects to an outlet that is close to the computer and easily accessible.
Setting up your work space Seating and posture The height of your chair in relation to the computer and keyboard as well as the support it gives your body are primary factors in reducing work strain. Refer to the following tips and to figure 3-1. BELOW EYE LEVEL GETTING STARTED FOOT REST 90O ANGLES Figure 3-1 Posture and positioning of the computer ❑ Place your chair so that the keyboard is at or slightly below the level of your elbow.
User's Manual Lighting Proper lighting can improve legibility of the display and reduce eye strain. ❑ Position the computer so that sunlight or bright indoor lighting does not reflect off the screen. Use tinted windows, shades or other screen to eliminate sun glare. ❑ Avoid placing the computer in front of bright light that could shine directly in your eyes. ❑ If possible, use soft, indirect lighting in your computer work area.
Connecting the AC adaptor Connecting the universal AC adaptor Attach the universal AC adaptor when you need to charge the battery or you want to operate from AC power. It is also the fastest way to get started, because the battery pack will need to be charged before you can operate from battery power. The universal AC adaptor can be connected to any power source supplying from 100 to 240 volts and 50 or 60 hertz.
User's Manual Opening the display The display panel can be rotated in a wide range of angles for optimal viewing. 1. Slide the display latch on the front of the computer to the right. 2. Lift the panel up and adjust it to the best viewing angle for you. CAUTION: Use reasonable care when opening and closing the display panel. Opening it vigorously or slamming it shut could damage the computer.
Starting up for the first time 2. Press and hold the computer’s power button for two or three seconds. Figure 3-5 Turning on the power When you first turn on the power, the computer’s initial screen is the Microsoft Windows XP Startup Screen Logo. Follow the on-screen directions for each screen. During setup, you can click the Back button to return to the previous screen. Be sure to read the Windows End User License Agreement display carefully. NOTE: Be sure to read the License Agreement carefully.
User's Manual 3. Click start then click Turn Off Computer. From the Turn Off Computer menu select Turn Off. 4. Turn off the power to any peripheral devices. CAUTION: Do not turn the computer or devices back on immediately. Wait a moment to let all capacitors fully discharge. Hibernation mode The hibernation feature saves the contents of memory to the hard disk when the computer is turned off. The next time the computer is turned on, the previous state is restored.
Turning off the power Starting Hibernation NOTE: You can also enable Hibernation by pressing Fn + F4. See Chapter 5, Keyboard, for details. To enter Hibernation mode, follow the steps below. 1. Click start . 2. Select Turn Off Computer. 3. Open the Turn Off Computer dialog box. Hibernate is not displayed. 4. Press the Shift key. The Standby item will change to Hibernate. 5. Select the Hibernate. Automatic Hibernation 1. Open the Control Panel. 2.
User's Manual CAUTION: Do not turn the computer or devices back on immediately. Wait a moment to let all capacitors fully discharge. Standby mode If you have to interrupt your work, you can turn off the power without exiting from your software. Data is maintained in the computer’s main memory. When you turn on the power again, you can continue working right where you left off. CAUTIONS: 1. Before entering Standby mode, be sure to save your data. 2.
Restarting the computer 2. Close the display panel. This feature must be enabled. Refer to the System Power Mode item in Power Saver Utility discribed in the Control Panel. Open Performance and Maintenance and open TOSHIBA Power Saver. 3. Press the power button. This feature must be enabled. Refer to the System Power Mode item in Power Saver Utility discribed in the Control Panel. Open Performance and Maintenance and open TOSHIBA Power Saver.
User's Manual 4. Press the power button and hold it down for five seconds. Wait 10 to 15 seconds, then turn the power on again by pressing the power button. Restoring the preinstalled software from the Product Recovery CD-ROM If preinstalled files are damaged, use the Product Recovery CD-ROM to restore them. To restore the operating system and all preinstalled software, follow the steps below.
Chapter 4 Operating Basics This chapter gives information on basic operations including using the pointing devices, USB diskette drive, optical media drives, Sub LCD, audio/video controls, the microphone, the internal modem, wireless communication, LAN, TOSHIBA Remote Control and changing Slim Select Bay modules. It also provides tips on caring for your computer, diskettes and CD/DVDs. Pointing devices The configuration, the computer is equipped a Touch Pad as a pointing device.
User's Manual Click: Tap the Touch Pad once Double-click: Tap twice Drag and drop: Tap to select the material you want to move. Leave your finger on the Touch Pad after the second tap and move the material. Using the USB diskette drive A 3 1/2" diskette drive connects to the computer’s USB port. It accommodates 1.44megabyte or 720-kilobyte diskettes. Refer to Chapter 2, Grand Tour, for more information.
Changing Slim Select Bay modules Disconnecting 3 1/2" diskette drive When you have finished using the diskette drive, follow the procedures below to disconnect it: 1. Wait for the indicator light to go out to make sure all diskette activity has stopped. CAUTION: If you disconnect the diskette drive or turn off the power while the computer is accessing the drive you may lose data or damage the diskette or the drive. 2. Click the Safety Remove Hardware icon on the Task Bar. 3. Click Diskette drive. 4.
User's Manual CAUTION: Wait for all disk indicators to go out before you turn over the computer and be careful to lay the computer down gently. Shock can damage the HDD or other components. 3. Slide the Slim Select Bay latch to the unlock position. 4. Grasp the DVD-ROM drive and slide it out. CAUTION: The DVD-ROM drive and other Slim Select Bay modules can become hot with use. Be careful when removing the module.
Using optical media drives Using optical media drives The text and illustrations in this section refer primarily to the DVD-ROM drive in the Slim Select Bay. However, operation is the same for the CD-RW/DVD-ROM drive and the DVD Multi drive in Slim Select Bay. The full-size drive provides highperformance execution of CD/DVD-ROM-based programs. You can run either 12 cm (4.72") or 8 cm (3.15") CD/DVDs without an adaptor. An ATAPI interface controller is used for CD/DVD-ROM operation.
User's Manual b. Pressing the eject button will not open the drawer when the DVD-ROM drive’s power is off. If the power is off, you can open the drawer by inserting a slender object (about 15 mm) such as a straightened paper clip into the eject hole just to the right of the eject button. 15 mm Diameter 1.0mm Figure 4-6 Manual release with the eject hole OPERATING BASICS 2. Pinch the drawer gently and pull until it is fully opened.
Using optical media drives 3. Lay the CD/DVD, label side up, in the drawer. Figure 4-8 Inserting a CD/DVD OPERATING BASICS NOTE: When the drawer is fully opened, the edge of the computer will extend slightly over the CD/DVD tray. Therefore, you will need to turn the CD/DVD at an angle when you place it in the tray. After seating the CD/DVD, however, make sure it lies flat, as shown in figure 4-8. CAUTIONS: 1. Do not touch the laser lens. Doing so could cause misalignment. 2.
User's Manual Figure 4-9 Closing the DVD-ROM drawer Removing discs OPERATING BASICS To remove the CD/DVD, follow the steps below and refer to figure 4-10. CAUTION: Do not press the eject button while the computer is accessing the Fixed DVD-ROM drive. Wait for the Disk indicator to go out before you open the drawer. Also, if the CD/DVD is spinning when you open the drawer, wait for it to stop before you remove it. 1. To pop the drawer partially open, press the eject button.
Writing CDs on CD-RW/DVD-ROM drive Figure 4-10 Removing a CD/DVD 3. Push the center of the drawer to close it. Press gently until it locks into place. Writing CDs on CD-RW/DVD-ROM drive NOTE: CD-R discs can be written to only once. CD-RW discs can be rewritten many times. Before writing or rewriting Please observe the following points when you write or rewrite the data. ❑ We recommend the following manufacturers of CD-R and CD-RW media. Media quality can affect write or rewrite success rates.
User's Manual CD-RW: MITUBISHI CHEMICAL CORPORATION RICOH Co., Ltd. OPERATING BASICS TOSHIBA has confirmed the operation of CD-R and CD-RW media of the manufacturers above. Operation of other media cannot be guaranteed. ❑ CD-RW can generally be rewritten about 1,000 times. However, the actual number of rewrites is affected by the quality of the media and the way it is used. ❑ Be sure to connect the universal AC adaptor when you write or rewrite.
Writing CD/DVDs on DVD-R/-RW drive • Open the optical media drive. ❑ If the media is poor in quality, dirty or damaged, writing or rewriting errors may occur. ❑ Set the computer on a level surface and avoid places subject to vibration such as airplanes trains, or cars. Do not use an unstable surface such as a stand. ❑ Keep mobile phones and other wireless communication devices away from the computer.
User's Manual Writing CD/DVDs on DVD Multi drive You can use the DVD Multi drive to write data to either CD-R/-RW or DVD-R/-RW/RAM discs. The following applications for writing are supplied on CD-ROM: Drag'n Drop CD, licensed by Easy Systems Japan Ltd., and DigiOn Inc., MotionDV STUDIO, DVDfunSTUDIO and DVD-MovieAlbum, licensed by Matsushita Electric Industrial Co.,Ltd.
Writing CD/DVDs on DVD Multi drive Read/write function chart Read Write Drag’n Drop CD*1 DVDfunSTUDIO*1 DVD-MovieAlbum*1 DVD-Video*2 DVD VR*2 (DVD VideoRecoding) CD-R CD-RW DVD-R DVD-RW DVD-RAM DVD+R DVD+RW Yes Yes Yes No No No Yes Yes Yes No No No Yes Yes Yes Yes No Yes Yes Yes Yes Yes No Yes Yes Yes No No Yes No No No No No No No No No No No No No No No No No Yes No No *1 Software supplied with the product can be used for writing to a disc. *2 Video format can be written.
User's Manual ❑ Based on TOSHIBA's limited compatibility testing, we suggest the following manufacturers of CD-R/-RW and DVD-R/-RW/-RAM disc. However, in no event does TOSHIBA guarantee the operation, quality or performance of any disc. Disc quality can affect write or rewrite success rates. CD-R: TAIYOYUDENCO.,LTD. Mitsui Chemicals Inc. MITUBISHI CHEMICAL CORPORATION RICOH Co., Ltd. Hitachi Maxell Ltd. CD-RW: MITUBISHI CHEMICAL CORPORATION RICOH Co., Ltd.
Writing CD/DVDs on DVD Multi drive ❑ Data written to a CD-R/DVD-R disc cannot be deleted either in whole or in part. ❑ Data deleted (erase) from a CD-RW and DVD-RW/-RAM disc cannot be recovered. Check the content of the disc carefully before you delete it. If multiple drives that can write data to discs are connected, be careful not to delete data from the wrong drive.
User's Manual ❑ Writing with software other than Drag'n Drop CD, DVDfunSTUDIO and DVDMovieAlbum is not recommended. When writing or rewriting Please observe/consider the following when you write or rewrite to a CD-R/-RW or DVD-R/-RW/-RAM disc. ❑ Do not perform any of the following actions when writing or rewriting: • Operate the computer for any other function, including using a mouse or Touch Pad or closing/opening the LCD panel. • Start a communication application such as a modem.
Writing CD/DVDs on DVD Multi drive ❑ Do not use the DISC Backup function of Drag'n Drop CD to copy DVD-Video and DVD-ROM with copyright protection, because the copy will not play correctly. ❑ DVD-RAM disc cannot be backed up with the DISC Backup function of Drag'n Drop CD. ❑ You cannot backup a CD-ROM or CD-R/-RW to DVD-R/-RW using the DISC Backup function of Drag'n Drop CD. ❑ You cannot back up DVD-ROM, DVD-Video or DVD-R/-RW to CD-R/-RW using the DISC Backup function of Drag'n Drop CD.
OPERATING BASICS User's Manual ❑ When Drag'n Drop or similar software is resident in the computer's memory, the DVD Multi drive locks. In this situation, other software cannot be used to write data to the disc. ❑ While you are editing DVD-R/-RW/-RAM, you can display previews. However, if an application other than WinDVD is running, the preview might not display properly. To ensure proper display of previews, do not start other applications while you are editing DVD-R/-RW/-RAM disc.
Media care Media care This section provides tips on protecting data stored on your CD/DVDs and diskettes. Handle your media with care. The following simple precautions will increase the lifetime of your media and protect the data stored on them: CD/DVDs 1. Store your CD/DVDs in the container they came in to protect them and keep them clean. 2. Do not bend the CD/DVD. 3. Do not write on, apply a sticker to, or otherwise mar the surface of the CD/DVD that contains data. 4.
User's Manual 6. Magnetic energy can destroy the data on your diskettes. Keep your diskettes away from speakers, radios, television sets and other sources of magnetic fields. Modem This section describes how to connect and disconnect the internal modem to and from a telephone jack. NOTE: The internal modem does not support voice functions. All data and fax functions are supported. CAUTIONS: 1. In case of a lightning storm, unplug the modem cable from the telephone jack. 2.
Modem Figure 4-11 The Region Selection icon 3. Click the icon with the primary mouse button to display a list of regions that the modem supports. A sub menu for telephony location information will also be displayed. A check will appear next to the currently selected region and telephony location. 4. Select a region from the region menu or a telephony location from the submenu. • When you click a region it becomes the modem’s region selection, and the New Location for telephony will be set automatically.
User's Manual Setting You can enable or disable the following settings: AutoRun Mode The Region Select utility starts automatically when you start up the operating system. Open the Dialing Properties dialog box after selecting region. The dialing properties dialog box will be displayed automatically after you select the region. Location list for region selection. A submenu appears displaying location information for telephony.
Wireless communications Figure 4-13 Connecting the internal modem CAUTION: Do not pull on the cable or move the computer while the cable is connected. NOTE: If you use a storage device such as a DVD-ROM drive, CD-RW/DVD-ROM drive or HDD connected to a 16-bit PC card, you might experience the following modem problems: 1. Modem speed is slow or communication is interrupted. 2. Skips may occur in sound. OPERATING BASICS Disconnecting To disconnect the internal modem cable, follow the steps below. 1.
User's Manual ❑ Automatic Transmit Rate Select mechanism in the transmit range of 54, 48, 36, 24, 18, 12, 9 and 6Mbit/s. (Revision A) ❑ Automatic Transmit Rate Select mechanism in the transmit range of 11, 5.5, 2 and 1Mbit/s. (Revision B) ❑ Automatic Transmit Rate Select mechanism in the transmit range of 108, 96.72, 48, 36, 24, 18 and 12Mbit/s. (Turbo Mode) ❑ Frequency Channel Selection (Revision A/Turbo Mode:5GHz, Revision B: 2.
Wireless communications Radio links You can easily establish links between two or more devices. The link is maintained even if the devices are not within line of sight. Security Two advanced security mechanisms ensure a high level of security: ❑ Authentication prevents access to critical data and makes it impossible to falsify the origin of a message. ❑ Encryption prevents eavesdropping and maintains link privacy.
User's Manual LAN The computer has built-in support for Ethernet LAN (10 megabits per second, 10BASE-T) and Fast Ethernet LAN (100 megabits per second, 100BASE-Tx). This section describes how to connect/disconnect to a LAN. CAUTION: Do not install or remove an optional memory module while Wake-up on LAN is enabled. NOTE: The Wake-up on LAN function consumes power even when the system is off. Leave the universal AC adaptor connected while using this feature.
Cleaning the computer 3. Plug the other end of the cable into a LAN hub connector. Check with your LAN administrator before connecting to a hub. NOTE: When the computer is exchanging data with the LAN, the LAN Active indicator glows yellow. When the computer is connected to a LAN hub but is not exchanging data, the Link indicator glows green. Disconnecting LAN cable To disconnect the LAN cable, follow the steps below.
User's Manual Moving the computer The computer is designed for rugged durability. However, a few simple precautions taken when moving the computer will help ensure trouble-free operation. ❑ Make sure all disk activity has ended before moving the computer. Check the Disk and Slim Select Bay indicators on the computer. ❑ If a CD/DVD is in the drives, remove it. Also make sure the drawer is securely closed. ❑ Turn off the power to the computer.
Chapter 5 The Keyboard The computer’s keyboard layouts are compatible with a 101/102-key enhanced keyboard. By pressing some keys in combination, all the 101/102-key keyboard functions can be executed on the computer. The number of keys on your keyboard depends on which country/region’s keyboard layout your computer is configured with. Keyboards for numerous languages are available. There are five types of keys: typewriter keys, keypad overlay, function keys, soft keys and cursor control keys.
User's Manual F1 … F12 function keys The function keys, not to be confused with Fn, are the 12 keys at the top of your keyboard. These keys function differently from other keys. F1 through F12 are called function keys because they execute programmed functions when pressed. Used in combination with the Fn key, keys marked with icons execute specific functions on the computer. See the section, Soft keys: Fn key combinations, in this chapter.
Soft keys: Fn key combinations The keyboard is designed to provide all the features of the 101-key enhanced keyboard, shown in figure 5-1. The 101/102-key enhanced keyboard has a numeric keypad and scroll lock key. It also has additional Enter and Ctrl keys to the right of the main keyboard. Since the keyboard is smaller and has fewer keys, some of the enhanced keyboard functions must be simulated using two keys instead of one on the larger keyboard.
User's Manual Hot keys Hot keys (Fn + a function or Esc key) let you enable or disable certain features of the computers. Sound mute: Pressing Fn + Esc in a Windows environment turns sound on or off. When you press these hot keys, the current setting will change and be displayed as an icon. Instant security: Press Fn + F1 to blank the screen to prevent others from accessing your data. To restore the screen and original settings, press any key or press the Touch Pad.
Soft keys: Fn key combinations Standby: When you press Fn + F3, the computer enters Standby. To avoid entering Standby unexpectedly, a dialog box appears for verification. However, if you select the check box, it will not appear in the future. Hibernation: When you press Fn + F4, the computer enters Hibernation. To avoid entering Hibernation unexpectedly, a dialog box appears for verification. However, if you select the check box, it will not appear in the future.
User's Manual LCD Display Brightness: Pressing Fn + F7 increases the display brightness in increments. When you press these hot keys, the current setting will be displayed for two seconds by a pop-up icon. You can also change this setting through the Monitor brightness item of the Power Save Mode window in Power Saver. NOTES: 1. The brightness level is always set at the maximum value for about 18 seconds, when the LCD turns on.
Windows special keys Fn Sticky key You can use the TOSHIBA Accessibility Utility to make the Fn key sticky, that is, you can press it once, release it, and they press an “F number” key. To start the TOSHIBA Accessibility Utility, click start, point to All Programs, point to TOSHIBA Utilities and click Accessibility. Windows special keys The keyboard provides two keys that have special functions in Windows : one activates the start menu and the other has the same function as the secondary mouse button.
User's Manual Numeric mode To turn on the Numeric mode, press Fn + F11. The Numeric mode F11 indicator lights. Now try numeric data entry using the keys in figure 5-2. Press Fn + F11 again to turn off the overlay. Figure 5-2 The numeric keypad overlay THE KEYBOARD Temporarily using normal keyboard (overlay on) While using the overlay, you can temporarily access the normal keyboard without turning off the overlay: 1. Hold Fn and press any other key. All keys will operate as if the overlay were off. 2.
Generating ASCII characters Temporarily using overlay (overlay off) While using the normal keyboard, you can temporarily use the keypad overlay without turning it on: 1. Press and hold down Fn. 2. Check the keyboard indicators. Pressing Fn turns on the most recently used overlay. If the Numeric mode indicator lights, you can use the overlay for numeric entry. If the Arrow mode indicator lights, you can use the overlay for cursor and page control. 3. Release Fn to return to normal keyboard operation.
THE KEYBOARD User's Manual 5-10
Power and Power-Up Modes The computer’s power resources include the universal AC adaptor and internal batteries. This chapter gives details on making the most effective use of these resources including charging and changing batteries, tips for saving battery power, and power up modes.
POWER AND POWER-UP MODES User's Manual Table 6-1 Power conditions continued Power on AC Battery • Operates adaptor charge is • LED: Battery off not above low connected battery Power off (no operation) DC IN off trigger point Battery • Operates charge is • LED: Battery below low flashes orange battery DC IN off trigger point Battery Computer goes charge is into resume mode exhausted shuts down No • Cannot operate battery • LED: Battery off installed DC IN off Power indicators
Battery types DC IN indicator Check the DC IN indicator to determine the power status with the universal AC adaptor connected: Green Flashing orange No light Indicates the universal AC adaptor is connected and supplying proper power to the computer. Indicates a problem with the power supply. Plug the universal AC adaptor into another outlet. If it still does not operate properly, see your dealer. Under any other conditions, the indicator does not light.
POWER AND POWER-UP MODES User's Manual Before you remove the battery pack, set the computer to Hibernation mode or save your data and shut down the computer. Do not change the battery pack while the universal AC adaptor is connected. CAUTIONS: 1. The battery pack is a lithium ion battery, which can explode if not properly replaced, used, handled or disposed of. Dispose of the battery as required by local ordinances or regulations. Use only batteries recommended by TOSHIBA as replacements. 2.
Care and use of the battery pack POWER AND POWER-UP MODES CAUTION: The computer’s RTC battery is a lithium ion battery and should be replaced only by your dealer or by a TOSHIBA service representative. The battery can explode if not properly replaced, used, handled or disposed of. Dispose of the battery as required by local ordinances or regulations. Care and use of the battery pack The battery pack is a vital component of portable computing.
POWER AND POWER-UP MODES User's Manual 4. Never puncture the battery pack with a nail or other sharp object. Never strike it with a hammer or other object. Never step on it. 5. Never try to charge the battery pack in any manner other than that described in the user’s manual. Never connect the battery pack to a plug socket or to a automobile’s cigarette lighter socket. It may rupture or ignite. 6.
Care and use of the battery pack 1. Never continue to use a battery pack after its recharging capacity has become impaired, or after the display of a warning message indicating that the battery pack’s power is exhausted. Continued use of an exhausted or impaired battery pack could cause the loss of data. 2. Never dispose of battery packs with normal trash. Bring them to your TOSHIBA dealer or to another recycling center to save resources and prevent environmental damage.
POWER AND POWER-UP MODES User's Manual Charging the batteries When the power in the battery pack becomes low, the Battery indicator flashes orange indicating that only a few minutes of battery power remain. If you continue to use the computer while the Battery indicator flashes, the computer enables Hibernation mode (so you don’t lose data) and automatically turns off.
Care and use of the battery pack The battery may not charge right away under the following conditions: ❑ The battery is extremely hot or cold. If the battery is extremely hot, it might not charge at all. To ensure the battery charges to its full capacity, charge the battery at room temperature of 10° to 30°C (50° to 88°F). ❑ The battery is nearly completely discharged. Leave the universal AC adaptor connected for a few minutes and the battery should begin charging.
POWER AND POWER-UP MODES User's Manual 2. With repeated discharges and recharges, the battery’s capacity will gradually decrease. Therefore, an often used, older battery will not operate for as long as a new battery even when both are fully charged. In this case, Power Save Modes window in TOSHIBA Power Saver will indicate a 100% charge for both the old and new battery, but the displayed estimated time remaining will be shorter for the older battery.
Care and use of the battery pack When you turn off your computer with fully charged batteries, the batteries retain data for the following approximate time periods: Battery pack about 6 days (Standby mode) about 30 days (Boot mode) RTC battery 1 month Extending battery life To maximize the life of your battery pack: ❑ At least once a month, disconnect the computer from a power source and operate it on battery power until the battery pack fully discharges. Before doing so, follow the steps below. 1.
POWER AND POWER-UP MODES User's Manual Replacing the battery pack When the battery pack reaches the end of its operating life you will need to install a new one. The life of the battery pack is generally about 500 recharges. If the Battery indicator flashes orange shortly after fully recharging the battery, the battery pack needs to be replaced. You might also replace a discharged battery pack with a charged spare when you are operating your computer away from an AC power source.
Replacing the battery pack POWER AND POWER-UP MODES BATTERY BATTERY PACK RELEASE LATCH Figure 6-1 Releasing the battery cover CAUTION: For environmental reasons, do not throw away a spent battery pack. Please return spent battery packs to your TOSHIBA dealer. Installing the battery pack To install a battery, follow the steps below. CAUTIONS: 1. The battery pack is a lithium ion battery, which can explode if not properly replaced, used, handled or disposed of.
POWER AND POWER-UP MODES User's Manual BATTERY RELEASE LATCH BATTERY PACK Figure 6-2 Securing the battery cover Starting the computer by password To start up the computer with the user password, follow these steps: 1. Turn on the power as described in Chapter 3, Getting Started. The following message appears: Password = NOTE: At this point, the hot keys Fn + F1 to F5 do not work. They will function after you enter the password. 2. Enter the password. 3. Press Enter.
Power-up modes The computer has the following power-up modes: ❑ Boot: Computer shuts down without saving data. Always save your work before you turn the computer off in boot mode. ❑ Hibernation: Data in memory is saved to the hard disk. ❑ Standby: Data is maintained in the computer’s main memory. NOTE: Refer also to the sections Turning on the power and Turning off the power in Chapter 3, Getting Started. Windows utilities You can specify the setting in TOSHIBA Power Saver.
POWER AND POWER-UP MODES User's Manual 6-16
Chapter 7 HW Setup and Passwords HW Setup TOSHIBA HW Setup lets you configure settings for Display, Boot Priority, Keyboard, USB, LAN, General, Password, Device Config and Parallel/Printer. NOTE: If the supervisor password is set, access to the TOSHIBA HW Setup program can be prevented when the user password is used to log on to the computer. Accessing HW Setup To run HW Setup, click start, click Control Panel and select TOSHIBA HW Setup.
User's Manual Display This tab lets you customize your computer’s display settings for either the internal LCD screen or for an external monitor. Power On Display HW SETUP AND PASSWORDS Lets you set the display to be used when the computer is booted. Auto-Selected Selects an external monitor if one is connected. Otherwise, it selects the internal LCD. (Default) LCD + AnalogRGB Selects both the internal LCD and external monitor for simultaneous display.
HW Setup 1. Hold down F12 and boot the computer. 2. The following menu will be displayed with the following icons: Built-in HDD, Slim Select Bay HDD, CD-ROM, FDD, Network (LAN), PCA (ATA) card boot. 3. Use the left/right cursor keys to highlight the boot device you want and press Enter. NOTES: 1. If a supervisor password is set, the menu above does not appear when you use the user password to start the computer. 2. The selection method above does not change the boot priority settings in HW Setup. 3.
User's Manual Built-in HDD −> PC Card −> 2nd HDD HDDs are searched for a boot command in the following order: the built-in HDD, the PC card and the HDD installed in the Slim Select Bay. HW SETUP AND PASSWORDS 2nd HDD −> PC Card −> Built-in HDD HDDs are searched for a boot command in the following order: the HDD installed in the Slim Select Bay, the PC card and the built-in HDD.
HW Setup USB USB KB/Mouse Legacy Emulation Use this option to enable or disable USB KB/Mouse Legacy Emulation. If your operating system does not support USB, you can still use a USB mouse and keyboard by setting the USB KB/Mouse Legacy Emulation item to Enabled. Enables the USB KB/Mouse Legacy Emulation. (Default) Disables the USB KB/Mouse Legacy Emulation. USB-FDD Legacy Emulation Use this option to enable or disable USB-FDD Legacy Emulation. Enabled Disabled Enables the USB-FDD Legacy Emulation.
User's Manual General This window displays the BIOS version and contains two buttons: Default and About. Setup HW SETUP AND PASSWORDS This field displays BIOS Version and date. Default Click Default to return all HW Setup values to the factory settings. About Click About to display the HW Setup version. Password User Password This option allows you to set or reset the user password for power on. Not Registered Registered Change or remove the password. (Default) Set the password.
HW Setup 4. If character strings match, the password is registered and the display changes to: The password was registered If they do not match, the following message appears. You must repeat from step 1. Entry Error!!! HW SETUP AND PASSWORDS To delete a user password: 1. Select Not Registered to display the following prompt: Enter Password: 2. Enter the currently registered password. The character string you enter is displayed as a string of asterisks.
User's Manual Key FD After you set a password, you can create a Key FD (diskette). If you forget the user password, the Key FD lets you bypass the password function. HW SETUP AND PASSWORDS NOTE: It is a good idea to create more than one Key FD in case a Key FD is damaged or lost. To create a Key FD follow the steps below. 1. Turn off the computer’s power. 2. Connect the diskette drive to a USB port on the computer. 3.
Supervisor password Parallel/Printer This tab lets you set the Parallel Port Mode. Use the Windows Device Manager to make settings for the Parallel port. Parallel Port Mode The options in this tab are ECP and Standard Bi-directional. Standard Bi-directional Sets the port type to Extended Capabilities Port (ECP). For most printers, the port should be set to ECP. (Default) This setting should be used with some other parallel devices.
HW SETUP AND PASSWORDS User's Manual 7-10
Chapter 8 Optional Devices Optional devices can expand the computer’s capabilities and its versatility.
User's Manual PC cards The computer is equipped with a PC card expansion slot that can accommodate two 5 mm Type II cards. Any PC card that meets industry standards (manufactured by TOSHIBA or other vendor) can be installed. The slot supports 16-bit PC cards, including PC card 16’s multifunction card and CardBus PC cards. CardBus supports the new standard of 32-bit PC cards. The bus provides superior performance for the greater demands of multimedia data transmission.
PC cards Removing a PC card To remove the PC card, follow the steps below. 1. Click the Safety Remove Hardware icon on the Task Bar. 2. Click PC card. 3. Press the PC card eject button to extend it. 4. Press the extended eject button to pop the card out slightly. 5. Pinch the PC card and remove it.
User's Manual SD cards The computer is equipped with an SD card slot that can accommodate Secure Digital flash memory cards with various memory capacities. SD cards let you easily transfer data from devices, such as digital cameras and Personal Digital Assistants, that use SD card flash-memory. The cards have a high level of security and copy protection features. The slot cannot accommodate MultiMedia cards. OPTIONAL DEVICES CAUTION: Keep foreign objects out of the SD card slot.
SD cards Removing an SD card To remove an SD card, follow the steps below. 1. Click the Safety Remove Hardware icon on the Task Bar. 2. Point to SD card and click. 3. Push in the card and release it to pop the card out slightly. 4. Grasp the card and remove it. OPTIONAL DEVICES SD CARD INDICATOR SD CARD Figure 8-4 Removing an SD card CAUTION: Make sure the SD card indicator is out before you remove the card or turn off the computer’s power.
User's Manual 5. Do not twist or bend SD cards. 6. Do not expose SD cards to liquids or store in humid areas or in lay media close to containers of liquid. 7. After using an SD card, return it to its case. 8. Do not touch the metal part or expose it to liquids or let it get dirty. Memory expansion This computer is equipped with two memory module sockets beneath the keyboard. You can increase the amount of RAM by installing an additional memory or replacing default memories with additional memories.
Memory expansion 4. Turn the computer to the normal position and open the display panel. Tilt the display panel slightly beyond the upright position before removing the keyboard display. 5. Put your fingers on the both ends of the keyboard brace and remove it carefully to the direction indicated with arrows. KEYBORD BRACE 6. Remove three screws (right and left at the both right and left end and in the upper middle of the keyboard) fixing the keyboard.
User's Manual OPTIONAL DEVICES 7. Press the keyboard to the other side. Turn the keyboard upside down when a flat cable appears.
Memory expansion 8. Raise the insulation sheet covering the memory module to appear the module. OPTIONAL DEVICES INSULATION SHEET Figure 8-9 Raising the insulation sheet CAUTION: Do not touch VGA chip, or you will get burnt. 9. Keep the insulation sheet raised using adhesive tape.
User's Manual OPTIONAL DEVICES 10. Insert a new module to the socket and push it downward to lie flat. Latches on either side will click into place to secure the module. Figure 8-11 Installing a memory module Figure 8-12 Installing two memory modules 11. Seat the insulation sheet to cover the module. NOTE: Be sure to check that the insulation sheet is returned to the original position to cover the memory module.
Memory expansion 12. Insert the tabs of the keyboard into the slits of the computer case and seat the keyboard at the original position. Fix it with three screws removed in 6. CAUTIONS: 1. Be sure to use all screws that were removed in 6 and do not leave foreign matters such as adhesive tape used in 9 or screws removed and dropped in the computer. 2.
OPTIONAL DEVICES User's Manual Figure 8-13 Removing the memory module 6. Follow the instructions 11 through 15 in “Installing memory module”. TOSHIBA Style Bay Bridge media adaptor You can insert three types of flash memory cards — CompactFlash, Memory Stick and SmartMedia — in the computer’s TOSHIBA Style Bay Bridge media adaptor. For details on using the adaptor, follow the steps below. For details on inserting modules in the Slim Select Bay, refer to Chapter 4, Operating Basics.
TOSHIBA Style Bay Bridge media adaptor Before installing Make sure you have the correct Bridge media adaptor case. Two cases come with the Bridge media adaptor: one marked A and one marked B. The case for the Satellite Pro M10 is marked with a B. NOTE: Case B is also used with the Satellite 2450 computer. Case A is used with the Satellite 5200 series. B OPTIONAL DEVICES Figure 8-14 The Bridge media adaptor case Inserting To install the Bridge media adaptor in the case, follow the steps below. 1.
User's Manual OPTIONAL DEVICES 3. Turn the Bridge media adaptor with case upside down and secure the case to the adaptor with one screw. Figure 8-16 Secureing a screw Removing To remove the Bridge media adaptor from the case, follow the steps below. 1. Turn the Bridge media adaptor with case upside down and remove one screw. 2. Slide the latch in the direction of the arrow shown below. 3. Push the Bridge media adaptor up from the bottom and lift it out.
TOSHIBA Style Bay Bridge media adaptor SmartMedia This slot accommodates 3.3 V SmartMedia (RAM) from 2 MB to 128 MB. ❑ You cannot use SmartMedia that does not conform to SSFDC specifications. ❑ Operation of SmartMedia developed after the computer was manufactured is not guaranteed. ❑ After you finish using SmartMedia, return it to its case, which is resistant to static electricity. Write protection SmartMedia can be write protected to safeguard your data.
User's Manual SMARTMEDIA OPTIONAL DEVICES SMARTMEDIA INDICATOR Figure 8-18 Inserting a SmartMedia Removing CAUTION: Do not remove a SmartMedia card while data is being written or read. Data could be destroyed. Wait for SmartMedia indicator on the left side of the SmartMedia slot to go out. 1. Right click (right button of the Touch Pad) on the SmartMedia drive’s icon and select Eject from the pop-up menu. 2. Push the card and release it. The card will pop out slightly. 3.
TOSHIBA Style Bay Bridge media adaptor Memory Stick This slot accommodates Memory Stick from 16MB to 128MB. NOTE: The slot does not support Magic Gate functions. Write protection Memory Stick can be write protected to safeguard your data. To write-protect a Memory Stick, slide the lock on the back of the Memory Stick to the lock position. Installing a Memory Stick To install a Memory Stick, follow the steps below. 1. Insert the Memory Stick into the slot. OPTIONAL DEVICES 2.
User's Manual CAUTION: Make sure the Memory Stick indicator is out before you remove the Memory Stick or turn off the computer’s power. If you remove the Memory Stick or turn off the power while the computer is accessing the Memory Stick, you may lose data or damage the Memory Stick. Compact Flash This slot accommodates Compact Flash from 16MB to 512MB. You cannot use Compact Flash that does not conform to CFA specifications.
Slim Select Bay HDD adaptor (Black) CAUTION: Make sure the Compact Flash indicator is out before you remove the Compact Flash or turn off the computer’s power. If you remove the Compact Flash or turn off the power while the computer is accessing the Compact Flash you may lose data or damage the Compact Flash. Bridge media care 1. Bridge media is consumable item, so make sure you back up important data. 2. Do not twist or bend Bridge media. 3.
User's Manual Slim Select Bay HDD adaptor (Black) A integrated 2 1/2" HDD is available for installation in the Slim Select Bay. To install an HDD in the Slim Select Bay HDD adaptor follow the steps below. OPTIONAL DEVICES 1. Slide the lock to the unlock position and open the lid. Figure 8-22 Opening the lid 2. Insert the HDD and push forward to ensure a firm connection.
TV 3. Close the lid and slide the lock to the lock position. For details on installing the Slim Select Bay HDD adaptor in the Slim Select Bay, refer to Chapter 4, Operating Basics. External monitor An external analog monitor can be connected to the external monitor port on the computer. The computer supports VGA and Super VGA video modes. To connect a monitor, follow the steps below. 1. Turn the computer off. 2. Connect the monitor to the external monitor port. 3. Turn the monitor’s power on. 4.
User's Manual TV You can connect a television set to the TV out jack on the computer. Follow the steps below. Using the TV button 1. Connect the TV adaptor cable’s S-Video plug to the TV out jack on the computer. 2. Connect the TV adaptor cable’s MINI DIN 4Pin connector S-Video format on the TV. OPTIONAL DEVICES 3. Press the TV button. You can use the hot keys Fn + F5 to change the display device. Refer to Chapter 5, The Keyboard.
i.LINK (IEEE1394) OPTIONAL DEVICES Figure 8-25 Display properties (3) Select the Adapter tab, then select List all modes. Figure 8-26 The Adapter window (4) Select a resolution from the menu.
User's Manual OPTIONAL DEVICES Figure 8-27 Resolution menu i.LINK (IEEE1394) i.LINK (IEEE1394) is used for high-speed data transfer for a range of compatible devices such as ❑ Digital video cameras ❑ Hard disk drives ❑ MO drives ❑ CD-RW drives NOTE: i.LINK uses a four-pin connector, which does not carry electric current. External devices will need their own power supply. Precautions ❑ Make a back-up of your data before transferring it to the computer.
Security lock ❑ If you are transferring data through an IEEE1394 hub, do not connect or disconnect other devices from the hub during data transfer. There is a likelihood that data will be damaged. Connect all devices to the hub before you turn on the computer’s power. ❑ You may not use any copyrighted video or music data copied from a video camera except for your personal enjoyment.
User's Manual Security lock A security lock enables you to anchor your computer to a desk or other heavy object to help prevent unauthorized removal of the computer. OPTIONAL DEVICES Attach one end of a cable to the desk and the other end to the security lock slot on the right side of the computer.
Chapter 9 Troubleshooting TOSHIBA designed the computer for durability. However, should problems occur, following the procedures in this chapter can help to determine the cause. All readers should become familiar with this chapter. Knowing what might go wrong can help prevent problems from occurring. Problem solving process Resolving problems will be much easier if you observe the following guidelines: ❑ Stop immediately when you recognize a problem exists.
User's Manual ❑ Check that your diskette or CD/DVD-ROM is correctly inserted and that the diskette’s write protect tab is correctly set. Make notes of your observations and keep them in a permanent error log. This will help you describe your problems to your dealer. If a problem recurs, the log will help you identify the problem faster. Analyzing the problem TROUBLESHOOTING Sometimes the system gives clues that can help you identify why it is malfunctioning.
Hardware and system checklist Hardware If you cannot find a software problem, check your hardware. First run through the items in the preliminary checklist above. If you still cannot correct the problem, try to identify the source. The next section provides checklists for individual components and peripherals. Hardware and system checklist This section discusses problems caused by your computer’s hardware or attached peripherals.
User's Manual Self test When the computer starts up, the self test will be run automatically, and the following will be displayed: In Touch with Tomorrow TOSHIBA This message remains on the screen for a few seconds. If the self test is successful, the computer tries to load the operating system. Depending on how the Boot Priority is set in the TOSHIBA HW Setup program.
Hardware and system checklist Overheating power down If the computer’s internal temperature becomes too high, the computer will automatically shut down. Problem Procedure Computer shuts down and DC IN indicator blinks orange Leave the computer off until the computer reaches room temperature, then turn it back on. If the computer is still too warm, the DC IN indicator will continue blinking when you turn on the power. Let it cool longer and try again.
User's Manual Battery If you suspect a problem with the battery, check the DC IN indicator as well as the Battery and Slim Select Bay indicators. For information on indicators and battery operation see Chapter 6, Power and Power-Up Modes. Problem Procedure Battery doesn’t power the computer The battery may be discharged. Connect the universal AC adaptor to charge the battery. Battery doesn’t charge when the universal AC adaptor is attached (Battery or Slim Select Bay indicator does not glow orange.
Hardware and system checklist Password Problem Procedure Cannot enter or forgot password Contact your dealer. NOTE: For information on setting a password, refer to Chapter 7, HW Setup and Passwords. Keyboard Keyboard problems can be caused by your setup configuration. For more information refer to Chapter 5, The Keyboard. Procedure Some letter keys produce numbers Check that the numeric keypad overlay is not selected. Press Fn + F10 and try typing again.
User's Manual Markings appear on the LCD. They might have come from contact with the keyboard, Touch Pad. Try wiping the LCD gently with a clean dry cloth. If markings remain, use LCD cleaner. Be sure to let the LCD dry before closing it. Problems above remain unresolved or other problems occur Refer to your software’s documentation to determine if the software is causing the difficulty. Contact your dealer if the problems continue.
Hardware and system checklist DVD-ROM drive For more information, refer to Chapter 4, Operating Basics. Problem Procedure You cannot access a CD/DVD in the drive Make sure the drive’s drawer is securely closed. Press gently until it clicks into place. Open the drawer and make sure the CD/DVD is properly seated. It should lie flat with the label facing up. A foreign object in the drawer could block laser light from reading the CD/DVD. Make sure there is no obstruction. Remove any foreign object.
User's Manual Check the region code on the DVD. It must match that on the DVD-ROM drive. Region codes are listed in the Optical media section in Chapter 2, The Grand Tour. If problems persist, contact your dealer. CD-RW/DVD-ROM drive For more information, refer to Chapter 4, Operating Basics. Problem Procedure You cannot access a CD/DVD in the drive Make sure the drive’s drawer is securely closed. Press gently until it clicks into place.
Hardware and system checklist DVD-ROM: DVD-ROM, DVD-Video CD-ROM: CD-DA, CD-Text, Photo CD (single/ multi-session), CD-ROM Mode 1, Mode 2, CD-ROM XA Mode 2 (Form1, Form2), Enhanced CD (CDEXTRA), CD-G (Audio CD only), Addressing Method 2 Check the region code on the DVD. It must match that on the CD-RW/DVD-ROM drive. Region codes are listed in the Optical media section in Chapter 2, The Grand Tour.
User's Manual DVD-R/-RW drive For more information, refer to Chapter 4, Operating Basics. Problem Procedure You cannot access a CD/DVD in the drive Make sure the drive’s drawer is securely closed. Press gently until it clicks into place. Open the drawer and make sure the CD/DVD is properly seated. It should lie flat with the label facing up. TROUBLESHOOTING A foreign object in the drawer could block laser light from reading the CD/DVD. Make sure there is no obstruction. Remove any foreign object.
Hardware and system checklist Check the region code on the DVD. It must match that on the CD-RW/DVD-ROM drive. Region codes are listed in the Optical media section in Chapter 2, The Grand Tour. Cannot write correctly If you have trouble writing, make sure you are observing the following precautions: • Use only media recommended by TOSHIBA. • Do not use the mouse or keyboard during writing. • Use only the software supplied with the computer for recording.
User's Manual Check whether the CD/DVD is dirty. If it is, wipe it with a clean cloth dipped in water or a neutral cleaner. See the Media care section in Chapter 4 for details on cleaning. Some CD/DVDs run correctly, but others do not The software or hardware configuration may be causing a problem. Make sure the hardware configuration matches your software’s needs. Check the CD/DVD’s documentation. TROUBLESHOOTING Check the type of CD/DVD you are using.
Hardware and system checklist • Do not run or start other software during writing. • Do not jar the computer during writing. • Do not connect/ disconnect external devices or install/remove internal cards during writing. If problems persist, contact your dealer. Diskette drive For more information, refer to Chapter 4, Operating Basics. Problem Procedure Drive does not operate There may be a faulty cable connection. Check the connection to the computer and to the drive.
User's Manual You cannot write to an SD card Make sure the card is not write protected. You cannot read a file Make sure the target file is on the SD Card inserted in the slot. If problems persist, contact your dealer. PC card Refer also to Chapter 8, Optional Devices. Problem Procedure PC card error occurs Reseat the PC card to make sure it is firmly connected. TROUBLESHOOTING Make sure the connection between the external device and the card is firm. Check the card’s documentation.
Hardware and system checklist Pointing device If you are using a USB mouse, also refer to the USB section in this chapter and to your mouse documentation. Touch Pad Problem Procedure On-screen pointer does not respond to Pad operation The system might be busy. If the pointer is shaped as an hourglass, wait for it to resume its normal shape and try again to move it. Double-tapping does not work Try changing the double-click speed setting in the mouse control utility. 1.
User's Manual USB mouse Problem Procedure On-screen pointer does not respond to mouse operation The system might be busy. If the pointer is shaped as an hourglass, wait for it to resume its normal shape and try again to move it. Make sure the mouse is properly connected to the USB port. Double-clicking does not work Try changing the double-click speed setting in the mouse control utility. 1. Open the Control Panel, select the Mouse icon and press Enter. 2. Click the Buttons tab. TROUBLESHOOTING 3.
Hardware and system checklist USB Refer also to your USB device’s documentation. Problem Procedure USB device does not work Check for a firm cable connection between the USB ports on the computer and the USB device. Make sure the USB device drivers are properly installed. Refer to your Windows XP documentation for information on checking the drivers. If problems persist, contact your dealer. Memory expansion Refer also to Chapter 8, Optional Devices, for information on installing memory modules.
User's Manual Sound system Refer also to documentation for your audio devices. Problem Procedure No sound is heard Adjust the volume control dial. Check the software volume settings. Make sure the headphone connection is secure. If problems persist, contact your dealer. Annoying sound is heard You may be experiencing feedback. Refer to Using the microphone in Chapter 4, Operating Basics. TROUBLESHOOTING If problems persist, contact your dealer.
Hardware and system checklist Display error occurs Check that the cable connecting the external monitor to the computer is attached firmly. If problems persist, contact your dealer. i.LINK (IEEE1394) Problem Procedure i.LINK device does not function Make sure the cable is securely connected to the computer and to the device. Make sure the device’s power is turned on. Reinstall the drivers. Open the Windows Control Panel and double-click the Add Hardware icon. Follow the on-screen directions.
User's Manual You can also use the ATX command. Refer to the online help files for Appendix C, AT Commands. You place a call, but a connection can’t be made Make sure the settings are correct in your communications application. After making a call you can’t hear a ring Make sure the tone or pulse selection in your communications application is set correctly. TROUBLESHOOTING You can also use the ATD command. Refer to the online help files for Appendix C, AT Commands.
Hardware and system checklist You can also use the ATS0 command. Refer to the online help files for Appendix D, S-registers. If problems persist, contact your dealer. LAN Problem Procedure Cannot access LAN Check for a firm cable connection between the LAN jack and the LAN HUB. Wake-up on LAN Make sure the universal AC adaptor is connected. The Wake-up on LAN function consumes power even when the system is off. does not work If problems persist, consult your LAN administrator.
User's Manual Bluetooth For more information on wireless communication, refer to Chapter 4, Operating Basics. Problem Procedure Cannot access Bluetooth device Make sure the computer’s wireless communication switch is set to on. Make sure the Bluetooth Manager is running and the power to the Bluetooth device is turned on. Make sure no optical Bluetooth PC card is installed in the computer. The built-in Bluetooth function and an optional Bluetooth PC card cannot operate simutaneously.
TOSHIBA support TOSHIBA support If you require any additional help using your computer or if you are having problems operating the computer, you may need to contact TOSHIBA for additional technical assistance. Before you call Some problems you experience may be related to software or the operating system, it is important to investigate other sources of assistance first.
TROUBLESHOOTING User's Manual UnitedKingdom United States of America TOSHIBA America Information Systems, TOSHIBA Information Systems (U.K.) Ltd. Inc. TOSHIBA Court 9740 Irvine Boulevard Weybridge Business Park Irvine, California 92618 Addlestone Road USA Weybridge, Surrey KT15 2UL InEurope The Rest of Europe Germany & Austria TOSHIBA Europe (I.E.) GmbH TOSHIBA Europe (I.E.
Specifications This appendix summarizes the computer’s technical specifications.
APPENDIX A User's Manual Communication specifications Communication system Data: Fax: Communication protocol Data ITU-T-Rec (Former CCITT) Bell Fax ITU-T-Rec (Former CCITT) Communication speed Transmitting level V.17/V.29/V.27ter /V.21 ch2 -10 dBm -10 to -40 dBm Input/output impedance Error correcting 600 ohms ±30% Power supply V.21/V.22/V.22bis/V.32 /V.32bis/V.34/V.
Appendix B Display Controller and Modes APPENDIX B Display controller The display controller interprets software commands into hardware commands that turn particular pels on or off. The controller is an advanced Video Graphics Array (VGA) that provides Extended Graphics Array (XGA) and Super Extended Graphics Array Plus (SXGA+) support for the internal LCD and external monitors. The 15.0" TFT LCD panel displays up to 1024 horizontal and 768 vertical pixels and 1400 horizontal and 1050 vertical pixels.
User's Manual Video modes APPENDIX B The computer supports video modes defined in the tables below. If your application offers a selection of mode numbers that do not match the numbers on the table, select a mode based on mode type, resolution, character matrix, number of colors and refresh rates. Also, if your software supports both graphics and text modes, the screen display may appear to operate faster using a text mode.
Appendix B Table1 Video modes (VGA) continued Type Resolution Character LCD matrix colors (pels) CRT colors Scanning frequency Vertical (Hz) D VGA Grph 320 x 200 Pels 8x8 16 of 256K 16 of 256K 70 E VGA Grph 640 x 200 Pels 8x8 16 of 256K 16 of 256K 70 F VGA Grph 640 x 350 Pels 8 x 14 Mono Mono 70 10 VGA Grph 640 x 350 Pels 8 x 14 16 of 256K 16 of 256K 70 11 VGA Grph VGA Grph 640 x 480 Pels 640 x 480 Pels 8 x 16 2 of 256K 2 of 256K 60 8 x 16 16 of 256K 16 of 256K 60
User's Manual APPENDIX B Table 2 Video modes (XGA) Resolution LCD colors CRT colors 640 x 480 256/256K 256/256K 60 75 85 100 800 x 600 256/256K 256/256K 60 75 85 100 1024 x 768 256/256K 256/256K 60 75 85 100 1280 x 1024 256/256K (Virtual) 256/256K 60 75 85 100 1600 x 1200 256/256K (Virtual) 256/256K 60 75 85 100 1920 x 1440 256/256K (Virtual) 256/256K 60 75 85 2048 x 1536 256/256K (Virtual) 256/256K 60 75 B-4 Vertical frequency (Hz)
Appendix B Table 2 Video modes (XGA) continued LCD colors CRT colors Vertical frequency (Hz) 640 x 480 64K/64K 64K/64K 60 75 85 100 800 x 600 64K/64K 64K/64K 60 75 85 100 1024 x 768 64K/64K 64K/64K 60 75 85 100 1280 x 1024 64K/64K (Virtual) 64K/64K 60 75 85 100 1600 x 1200 64K/64K (Virtual) 64K/64K 60 75 85 100 1920 x 1440 64K/64K (Virtual) 64K/64K 60 75 85 2048 x 1536 64K/64K (Virtual) 64K/64K 60 75 APPENDIX B Resolution B-5
User's Manual APPENDIX B Table 2 Video modes (XGA) continued Resolution LCD colors CRT colors 640 x 480 16M/16M 16M/16M 60 75 85 100 800 x 600 16M/16M 16M/16M 60 75 85 100 1024 x 768 16M/16M 16M/16M 60 75 85 100 1280 x 1024 16M/16M (Virtual) 16M/16M 60 75 85 100 1600 x 1200 16M/16M (Virtual) 16M/16M 60 75 85 100 1920 x 1440 16M/16M (Virtual) 16M/16M 60 75 2048 x 1536 16M/16M (Virtual) 16M/16M 60 B-6 Vertical frequency (Hz)
Appendix B Table 3 Video modes (Super XGA+) LCD colors CRT colors Vertical frequency (Hz) 640 x 480 256/256K 256/256K 60 75 85 100 800 x 600 256/256K 256/256K 60 75 85 100 1024 x 768 256/256K 256/256K 60 75 85 100 1280 x 1024 256/256K 256/256K 60 75 85 100 1400 x 1050 256/256K 256/256K 60 75 85 100 1600 x 1200 256/256K (Virtual) 256/256K 60 75 85 100 1920 x 1440 256/256K (Virtual) 256/256K 60 75 85 2048 x 1536 256/256K (Virtual) 256/256K 60 75 APPENDIX B Resolution B-7
User's Manual APPENDIX B Table 3 Video modes (Super XGA+) continued Resolution LCD colors CRT colors 640 x 480 64K/64K 64K/64K 60 75 85 100 800 x 600 64K/64K 64K/64K 60 75 85 100 1024 x 768 64K/64K 64K/64K 60 75 85 100 1280 x 1024 64K/64K 64K/64K 60 75 85 100 1400 x 1050 64K/64K 64K/64K 60 75 85 100 1600 x 1200 64K/64K (Virtual) 64K/64K 60 75 85 100 1920 x 1440 64K/64K (Virtual) 64K/64K 60 75 85 2048 x 1536 64K/64K (Virtual) 64K/64K 60 75 B-8 Vertical frequency (Hz)
Appendix B Table 3 Video modes (Super XGA+) continued LCD colors CRT colors Vertical frequency (Hz) 640 x 480 16M/16M 16M/16M 60 75 85 100 800 x 600 16M/16M 16M/16M 60 75 85 100 1024 x 768 16M/16M 16M/16M 60 75 85 100 1280 x 1024 16M/16M 16M/16M 60 75 85 100 1400 x 1050 16M/16M 16M/16M 60 75 85 100 1600 x 1200 16M/16M (Virtual) 16M/16M 60 75 85 100 1920 x 1440 16M/16M (Virtual) 16M/16M 60 75 2048 x 1536 16M/16M (Virtual) 16M/16M 60 APPENDIX B Resolution B-9
APPENDIX B User's Manual B-10
Appendix C AT Commands In most cases, you will not need to type AT commands manually. However, there might be some occasions when you will need to do so. This chapter describes AT commands for data mode. Fax and voice commands are taken care of by application software. The format for entering AT commands is: ATXn Any command issued is acknowledged with a response in either text or numeric values known as result codes.
User's Manual A Answer command This command instructs the modem to go off-hook and answer an incoming call. Bn Communication standard setting This command determines the communication standard CCITT or Bell. B0 Selects CCITT V.22 mode when the modem is at 1200 bps. B1 Selects Bell 212A when the modem is at 1200 bps (default). B15 Selects V.21 when the modem is at 300 bps. B16 Selects Bell 103J when the modem is at 300 bps (default).
Appendix C En ; Return to command mode. Causes the modem to return to command mode after dialing a number, without disconnecting the call. S=n Dial a telephone number previously stored using the &Zn=X command (See &Zn=X command for more information). The range is 0-3. Echo command This command controls whether or not the characters entered from your computer keyboard are displayed on your monitor (echoed) while the modem is in command mode. E0 Disables echo to the computer.
User's Manual Ln Monitor speaker volume This command sets speaker volume to low, medium, or high. L0 Low volume. L1 Low volume. (Same as L0) L2 Medium volume (default). L3 High volume. Result Codes: OK n=0,1,2,3 ERROR Otherwise Mn Monitor speaker mode APPENDIX C This command turns the speaker on or off. M0 The speaker is off. M1 The speaker is on until the modem detects the carrier signal (default). M2 The speaker is always on when modem is off-hook.
Appendix C Result Codes: n=0,1 OK ERROR Otherwise On Return on-line to data mode O0 Instructs the modem to exit on-line command mode and return to data mode (see AT escape sequence, +++). O1 This command issues a retrain before returning to on-line data mode. O3 This command issues a rate renegotiation before returning to on-line data mode. Result Codes: OK n=0,1,3 P Otherwise Select pulse dialing This command configures the modem for pulse (non touch-tone) dialing.
User's Manual T Select tone dialing This command instructs the modem to send DTMF tones while dialing. Dialed digits are tone dialed until a P command or dial modifier is received. This is the default setting. Vn DCE response format This command controls whether result codes (including call progress and negotiation progress messages) are displayed as words or their numeric equivalents. V0 Displays result codes as digits. V1 Displays result codes as text (default).
Appendix C X5 Enable Enable OK, RING, NO CARRIER, ERROR, NODIALTONE, BUSY, CONNECT , RRING, NO BONGTONE, DELAYED, BLACKLISTED, REORDER, WARBLE, CALL WAITING DETECTED Dial tone detect Disabled: The modem dials a call regardless of whether it detects a dial tone. Enabled: The modem dials only upon detection of a dial tone, and disconnects the call if the dial tone is not detected within 10 seconds. APPENDIX C Busy tone detect Disabled: The modem ignores any busy tones it receives.
User's Manual &C1 DCD turns on when the remote modem’s carrier signal is detected, and off when the carrier signal is not detected (default). Result Codes: OK n=0,1 ERROR Otherwise &Dn DTR control APPENDIX C This command interprets how the modem responds to the state of the DTR signal and changes to the DTR signal. &D0 Ignore. The modem ignores the true status of DTR and treats it as always on.
Appendix C &Gn V.22bis guard tone control This command determines which guard tone, if any, to transmit while transmitting in the high band (answer mode). This command is only used in V.22 and V.22bis mode. This option is not used in North America and is for international use only. &G0 Guard tone disabled (default). &G1 Sets guard tone to 550 Hz. &G2 Sets guard tone to 1800 Hz. Result Codes: OK n=0,1,2 ERROR Otherwise &Kn Local flow control selection Disable flow control.
User's Manual &T0 Abort. Stops any test in progress. &T1 Local analog loop. This test verifies modem operation, as well as the connection between the modem and computer. Any data entered at the local DTE is modulated, then demodulated, and returned to the local DTE. To work properly, the modem must be off-line. Result Codes: OK n=0 CONNECT n=1 ERROR Otherwise APPENDIX C &V Display Current Configuration This command displays the current configuration of the modem.
Appendix C \Nn Error control mode selection This command determines the type of error control used by the modem when sending or receiving data. \N0 Buffer mode. No error control. \N1 Direct mode. \N2 MNP or disconnect mode. The modem attempts to connect using MNP2-4 error control procedures. If this fails, the modem disconnects. This is also known as MNP reliable mode. \N3 V.42, MNP, or buffered (default). \N4 V.42 or disconnect. The modem attempts to connect in V.42 error control mode.
User's Manual \Vn Protocol result code \V0 Disable protocol result code appended to DCE speed. \V1 Enable protocol result code appended to DCE speed (default). Result Codes: OK n=0,1 ERROR Otherwise % B View numbers in blacklist If blacklisting is in effect, this command displays the numbers for which the last call attempted in the past two hours failed. The ERROR result code appears in regions that do not require blacklisting.
Appendix D S-registers S-registers contain the settings that determine how a number of functions of the internal modem operate. For example, how many times to let the telephone ring before the modem answers and how long to wait before it hangs up if a connection fails. You can also customize certain AT commands such as the escape sequence and command line termination. The contents of the registers are changed automatically when you modify corresponding settings in your communication software.
User's Manual S0 Auto answer ring number This register determines the number of rings the modem will count before automatically answering a call. Enter 0 (zero) if you do not want the modem to automatically answer at all. When disabled, the modem can only answer with an ATA command. Range: 0-255 Default: 0 Units: S1 rings Ring counter This register is read only. The value of S1 is incremented with each ring. If no ring occurs over a six-second interval, this register is cleared.
Appendix D S4 Response formatting character (user defined) This register determines the ASCII value used as the line feed character. The modem uses a line feed character in command mode when it responds to the computer. Range: 0-127, ASCII decimal Default: 10 (line feed) Units: S5 ASCII Command line editing character (user defined) This register sets the character recognized as a backspace and pertains to asynchronous only.
User's Manual S7 Connection completion time-out This register sets the time, in seconds, that the modem must wait before hanging up because carrier is not detected. The timer is started when the modem finishes dialing (originate), or goes off-hook (answer). In originate mode, the timer is reset upon detection of an answer tone if allowed by county restriction. The timer also specifies the wait for silence time for the @ dial modifier in seconds. S7 is not associated with the W dial modifier.
Appendix C S37 Dial line rate maximum modem speed S37 = 1 reserved S37 = 2 1200/75 bps S37 = 3 300 bps S37 = 4 reserved S37 = 5 1200 bps S37 = 6 2400 bps S37 = 7 4800 bps S37 = 8 7200 bps S37 = 9 9600 bps S37 = 10 12000 bps S37 = 11 14400 bps S37 = 12 16800 bps S37 = 13 19200 bps S37 = 14 21600 bps S37 = 15 24000 bps S37 = 16 26400 bps S37 = 17 28800 bps S37 = 18 31200 bps S37 = 19 33600 bps APPENDIX D S37 = 0 (default) D-5
User's Manual AT command set result codes The following table shows the result codes.
Appendix C Result Code Numeric Description DELAYED*2 88 Delay is in effect for the dialed number BLACKLISTED*2 89 Dialed number is blacklisted BLACKLIST FULL*2 90 Blacklist is full *1: EC only appears when the Extended Result Codes configuration option is enabled. EC is replaced by one of the following symbols, depending upon the error control method used: V.42bis - V.42 error control and V.42bis data compression. V.42 - V.42 error control only.
APPENDIX D User's Manual D-8
Appendix E V.90 The TOSHIBA internal modem uses V.90 technology. The modem is capable of downstream speeds of 56Kbps (kilobits per second) when connected to an Internet service provider that supports V.90. As with any modem, the actual throughput (speed of data transfer) depends on analog telephone line conditions, which can vary considerably. Therefore, many users will experience throughput in the range of 28-50Kbps under normal telephone line conditions. Upstream data flows at the V.34 rate. NOTE: V.
User's Manual APPENDIX E Table E-1 Result codes for a V.90 connection No.
Appendix E * EC stands for the Error Control method, which appears only when the extended result codes configuration option is enabled. EC is replaced by one of the following symbols, depending on the error control method used. V42bis V42 NoEC V.42 error control and V.42bis data compression V.42 error control only No error control protocol AT Command -V90=* V.90 Dial Line Rate -V90 sets the maximum V.90 downstream that the modem attempts to connect. -V90=0 V.90 disabled -V90=1 V.
APPENDIX E User's Manual E-4
Internal Modem Guide This appendix describes how to install and the remove the internal modem. CAUTION: Do not disassemble the computer beyond the steps described in this instruction or touch any components not specifically described. Installing the internal modem NOTE: The internal modem is preinstalled. The following is for information only. To install the internal modem follow the procedures below. Installing the modem board and jack To install the modem board and jack, follow the steps below. 1.
APPENDIX F User's Manual 5. Pull the guide (plastic tab) toward the direction shown by arrow, then lift the HDD. Be careful not to damage the connector. GUIDE (PLASTIC TAB) 6. Remove two screws, which you use later to secure the modem board. 7. Connect the modem board cable and seat the modem board. 8. Secure the modem board with two screws removed in step 6. 9. Secure the cover with one screw. Removing the internal modem To remove the internal modem, follow the steps below. 1.
Appendix G Wireless LAN Form Factor Capability Network Operating System Media Access Protocol Data Rate - Mini PCI TypeIII - EEE 802.11 Standard for Wireless LANS (DSSS) Wi-Fi (Wireless Fidelity) certified by the Wireless Ethernet Compatibility Alliance (WECA) - Microsoft Windows® Networking - CSMA/CA (Collision Avoidance) with Acknowledgment (ACK) - 54/48/36/24/18/12/9/6 Mb/s (Revision A) - 11/5.
User's Manual Modulation Technique Direct Sequence Spread Spectrum - CCK, DQPSK, DBPSK (Revision B) - OFDM-BPSK, OFDM-QPSK, OFDM-16QAM, OFDM64QAM (Revision A, Turbo Mode) APPENDIX G The range of the wireless signal is related to the Transmit Rate of the wireless communication. Communications at lower Transmit range may travel larger distances. ❑ The range of your wireless devices can be affected when the antennas are placed near metal surfaces and solid high-density materials.
Appendix G When installing Wireless LAN Cards, the channel configuration is managed as follows: For wireless clients that operate in a Wireless LAN Infrastructure, the Wireless LAN Card will automatically start operation at the channel identified by the Wireless LAN Access Point, When roaming between different access points the station can dynamically switch to another channel if required.
User's Manual Wireless Channels Sets (Turbo Mode) Frequency Range 5150-5850MHz Note 42 5210 US only *1 50 5250 US only *1 58 5290 US only *1 152 5760 US only *1 160 5800 US only *1 APPENDIX G Channel ID *1: Available Area: US (USA, CANADA) only A peer-to-peer mode is available under the following condition; A Wireless LAN card receive a "US country code" beacon of the standard IEEE802.11 (Revision D) from the near Wireless LAN Access Point.
Appendix H AC Power Cord and Connectors The power cord’s AC input plug must be compatible with the various international AC power outlets and the cord must meet the standards for the country/region in which it is used. All cords must meet the following specifications: Minimum 2 meters Wire size: Minimum 0.75 mm2 Current rating: Minimum 2.5 amperes Voltage rating: 125 or 250 VAC (depending on country/region’s power standards) Certification agencies U.S. and Canada: UL listed and CSA certified No.
User's Manual The following illustrations show the plug shapes for the U.S.A. and Canada, the United Kingdom, Australia and Europe.
Appendix I Parts Numbers The computer configuration and parts numbers, printed on a label on the bottom of the computer, indicate the CPU, LCD, memory, HDD, Slim Select Bay modules and communication devices.
User's Manual Configurations The following table shows the computer configuration indicated on a label. Shaded areas indicate abbreviations used on the label. The explanations are to the left of the shading. Abbreviations are not limited to those in this chart. They may change without notice. APPENDIX I CPU Pentium4 DT P4 2.26 DT P4 2.4 DT P4 2.53 DT P4 2.66 DT P4 2.8 P4-2.26 P4-2.4 P4-2.53 P4-2.66 P4-2.
The terms in this glossary cover topics related to this manual. Alternate naming is included for reference.
GLOSSARY Adaptor (Abbreviations continued) TFT: thin-film transistor UART: universal asynchronous receiver/transmitter USB: Universal Serial Bus UXGA: ultra extended graphics array VESA: Video Electronic Standards Association VGA: video graphics array VRT: voltage reduction technology XGA: extended graphics array A adaptor: A device that provides an interface between two dissimilar electronic devices. For example, the AC adaptor modifies the power from a wall outlet for use by the computer.
cache memory backup: A duplicate copy of files kept as a spare in case the original is destroyed. batch file: A file that can be executed from the system prompt containing a sequence of operating system commands or executable files. binary: The base two number system composed of zeros and ones (off or on), used by most digital computers. The right-most digit of a binary number has a value of 1, the next a value of 2, then 4, 8, 16, and so on. For example, the binary number 101 has a value of 5.
GLOSSARY capacity capacity: The amount of data that can be stored on a magnetic storage device such as a diskette (floppy disk) or hard disk. It is usually described in terms of kilobytes (KB), where one KB = 1024 bytes and megabytes (MB), where one MB = 1024 KB. CMOS: Complementary Metal-Oxide Semiconductor. An electronic circuit fabricated on a silicon wafer that requires very little power. Integrated circuits implemented in CMOS technology can be tightly packaged and are highly reliable.
dielete computer program: A set of instructions written for a computer that enable it to achieve a desired result. computer system: A combination of hardware, software, firmware, and peripheral components assembled to process data into useful information. configuration: The specific components in your system (such as the terminal, printer, and disk drives) and the settings that define how your system works. You use the HW Setup program to control your system configuration. CRT: Cathode Ray Tube.
GLOSSARY device driver device driver: A program that controls communication between a specific peripheral device and the computer. The CONFIG.SYS file contains device drivers that MS-DOS loads when you turn the computer on. dialog box: A window that accepts user input to make system settings or record other information. disk drive: The device that randomly accesses information on a disk and copies it to the computer’s memory. It also writes data from memory to the disk.
hard disk drive (HDD) execute: To interpret and execute an instruction. folder: An icon in Windows used to store documents or other folders. format: The process of readying a blank disk for its first use. Formatting establishes the structure of the disk that the operating system expects before it writes files or programs onto the disk. Extended Capability Port: An industry standard that provides a data buffer, switchable forward and reverse data transmission, and run length encoding (RLE) support.
GLOSSARY hardware hardware: The physical electronic and mechanical components of a computer system: typically, the computer itself, external disk drives, etc. See also software and firmware. hertz: A unit of wave frequency that equals one cycle per second. hexadecimal: The base 16 numbering system composed of the digits 0 through 9 and the letters A, B, C, D, E, and F. host computer: The computer that controls, regulates, and transmits information to a device or another computer.
menu jumper: A small clip or wire that allows you to change the hardware characteristics by electrically connecting two points of a circuit. K K: Taken from the Greek word kilo, meaning 1000; often used as equivalent to 1024, or 2 raised to the 10th power. See also byte and kilobyte. KB: See kilobyte. keyboard: An input device containing switches that are activated by manually pressing marked keys. Each keystroke activates a switch that transmits a specific code to the computer.
GLOSSARY microprocessor microprocessor: A hardware component contained in a single integrated circuit that carries out instructions. Also called the central processing unit (CPU), one of the main parts of the computer. N mode: A method of operation, for example, the boot mode, standby mode or the hibernation mode. nonvolatile memory: Memory, usually read-only (ROM), that is capable of permanently storing information. Turning the computer’s power off does not alter data stored in nonvolatile memory.
prompt peripheral device: An I/O device that is external to the central processor and/or main memory such as a printer or a mouse. P plug and play: A capability with Windows that enables the system to automatically recognize connections of external devices and make the necessary configurations in the computer. parallel interface: Refers to a type of information exchange that transmits information one byte (8 bits) at a time. See also serial interface.
GLOSSARY Radio frequency interference (RFI) shield R Radio frequency interference (RFI) shield: A metal shield enclosing the printed circuit boards of the printer or computer to prevent radio and TV interference. All computer equipment generates radio frequency signals. The FCC regulates the amount of signals a computing device can allow past its shielding. A Class A device is sufficient for office use. Class B provides a more stringent classification for home equipment use.
write protection TouchPad: A pointing device integrated into the TOSHIBA computer palm rest. stop bit: One or more bits of a byte that follow the transmitted character or group codes in asynchronous serial communications. U subpixel: Three elements, one red, one green and blue (RGB), that make up a pixel on the color LCD. The computer sets subpixels independently, each may emit a different degree of brightness. See also pixel.
GLOSSARY Glossary Glossary-14
Index Index C AC adaptor, See Universal AC adaptor ASCII characters 5-9 Audio/Video control buttons 1-6, 2-1, 4-16 Cache memory 1-2 CD-RW/DVD-ROM drive 1-4, 1-12 location 2-4 problems 9-10 using 4-5 view 2-14 writing CDs 4-9 Cleaning the computer 4-27 Compact Flash, See Bridge media Cooling (heat dispersal) 1-9 location of vents 2-2, 2-5 settings 4-28 CPU, See Processor B Battery automatic hibernation 1-9 charging 6-8 extending life 6-11 indicator 2-10, 6-2 location 2-7 monitoring capacity 6-9 real time
User's manual INDEX E Environment 3-1 Equipment checklist 1-1 Equipment setup general conditions 3-2 placement 3-2 Ergonomics lighting 3-4 seating and posture 3-3 work habits 3-4 Expansion memory, See Memory F Fn + Ctrl (enhanced keyboard simulation) 5-3 Fn + Enter 5-3 Fn + Esc (sound mute) 5-4 Fn + F1 (instant security) 5-4 Fn + F2 (power save mode) 5-4 Fn + F3 (standby) 5-5 Fn + F4 (hibernation) 5-5 Fn + F5 (display selection) 5-5 Fn + F6 (display brightness) 5-5 Fn + F7 (display brightness) 5-6 Fn + F
Index K N L Numeric keypad, See Keypad overlay LAN 1-7 connecting 4-26 disconnecting 4-27 jack 2-6 LAN active indicator 2-5 link indicator 2-5 problems 9-23 LCD, See Display, Video modes and Monitor external Level 2 cache, See Cache memory Line-in jack, See Sound system Line-out jack, See Sound system Lock security, See Security lock O M Media care CD/DVDs 4-19 diskettes 4-19 SD card 8-5 Memory 1-2 Overlay, See Keypad overlay P Panel power off, See Power Password Key FD 7-8 power on 1-9 problems 9-
INDEX User's manual Ports external monitor 1-5 i.
Index T TOSHIBA Console 1-10 TOSHIBA Console button 1-8, 2-9 TOSHIBA Controls 1-10 TOSHIBA Power Saver 1-10 Touch Pad 1-5 buttons 2-9 location 2-8 problems 9-17 using 4-1 Troubleshooting, See Problems TV 8-22 TV button 1-6, 2-9 using 8-22 V Video modes Appendix B Video RAM 1-2 Video-out jack, See Sound system Volume control, See Sound system W Wireless communication 4-23 indicators 2-2, 4-25 setting by hot keys 5-6 switch 2-2, 4-25 Wireless LAN 1-7 problems 9-23 using 4-23 INDEX Sound system 1-6 headph
INDEX User's manual Index-6
