GMR300648xx0_Cover.ai 2006-12-06 10:27:00 User’s Manual A100 GMR300648EN0 GMR300648EN0 Choose freedom. computers.toshiba-europe.com Choose freedom. computers.toshiba-europe.
TOSHIBA A100 Copyright © 2006 by TOSHIBA Corporation. All rights reserved. Under the copyright laws, this manual cannot be reproduced in any form without the prior written permission of TOSHIBA. No patent liability is assumed, with respect to the use of the information contained herein.
TOSHIBA A100 InterVideo and WinDVD are registered trademarks of the InterVideo Inc. DVD MovieFactory is trademarks of the Ulead Systems. Inc. Other trademarks and registered trademarks not listed above may be used in this manual. Macrovision License of Notice This product incorporates copyright protection technology that is protected by methods and claims of certain U.S. patents and other intellectual rights owned by Macrovision Corporation, and other rights owners.
TOSHIBA A100 ■ Before you connect the computer to a power source, ensure that the voltage rating of the AC adapter matches that of the available power source. 115 V/60 Hz in most of North and South America and some Far Eastern countries such as Taiwan. 100 V/50 Hz in eastern Japan and 100 V/60 Hz in western Japan. 230 V/50 Hz in most of Europe, the Middle East, and the Far East.
TOSHIBA A100 Modem warning notice Conformity Statement The equipment has been approved to [Commission Decision "CTR21"] for pan-European single terminal connection to the Public Switched Telephone Network (PSTN). However, due to differences between the individual PSTNs provided in different countries/regions the approval does not, of itself, give an unconditional assurance of successful operation on every PSTN network termination point.
TOSHIBA A100 Optical disk drive safety instructions TOSHIBA A100 computer is shipped with one of the following drives preinstalled: DVD-ROM, CD-RW/DVD-ROM, or DVD Super Multi (+-R DL) drive. The optical disc drive employs a laser system. To ensure proper use of this product, please read the manual carefully and retain for future reference. Should the unit ever require maintenance, contact an authorized service location.
TOSHIBA A100 This computer is equipped with one of the optical drive in the following list according to the model: User’s Manual Manufacturer Type HLDS DVD Super Multi (±R Double Layer) GSA-T10-ATAKK0 HLDS DVD Super Multi (±R Double Layer) GMA-4082N-ATAKK0 Matsushita DVD Super Multi (±R Double Layer) UJ-841BTJV-A NEC DVD Super Multi (±R Double Layer) ND-7550 Panasonic DVD Super Multi (±R Double Layer) UJ-850B Pioneer DVD Super Multi (±R Double Layer) DVD-K16 Teac DVD Super Multi (±R Double
TOSHIBA A100 Important Notice Copyrighted works including, but not limited to music, video, computer program, databases are protected by copyright laws. Unless specifically permitted under applicable copyright laws, you cannot copy, modify, assign, transmit or otherwise dispose of any copyrighted work with the consent of the owner of the copyright. Please take notice that unauthorized copying, modification, assignment, transmission and disposition may be subject to claims for damages and penalties.
Table of Contents Chapter 1 Introduction Equipment checklist. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-1 Features. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-3 Special Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-9 TOSHIBA Value Added Package . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-11 Utilities and Application. . . . . . . . . . . . . . . . . . . .
TOSHIBA A100 Chapter 4 Operating Basics Using the Touch Pad . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-1 Using the USB diskette drive . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-2 Using optical media drives . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-3 AV Button function (Provided with some models) . . . . . . . . . . . . . . 4-7 Writing CDs on CD-RW/DVD-ROM drive. . . . . . . . . . . . . . . . . . . . . . .
TOSHIBA A100 Chapter 8 Optional Devices PC cards . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-2 Express Card . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-3 Multiple Digital Media Card Slot . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-5 Memory expansion . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-7 Additional battery pack (6 Cell, 9 Cell and 12 Cell) . . . .
Preface Congratulations on your purchase of the TOSHIBA A100 computer. This powerful, lightweight notebook computer is designed to provide years of reliable, high-performance computing. This manual tells how to set up and begin using your Toshiba A100 computer. It also provides detailed information on configuring your computer, basic operations and care, using optional devices and troubleshooting.
TOSHIBA A100 Chapter 4, Operating Basics, includes tips on care of the computer and on using the Touch Pad, optical media drive, external diskette drive, Wireless LAN, LANs, Audio/Video controls, and internal modem. Chapter 5, The Keyboard, describes special keyboard functions including the keypad overlay and hot keys. Chapter 6, Power and Power-Up Modes, gives details on the computer’s power resources and battery save modes.
TOSHIBA A100 Key operation Some operations require you to simultaneously use two or more keys. We identify such operations by the key top symbols separated by a plus sign (+). For example, Ctrl + C means you must hold down Ctrl and at the same time press C. If three keys are used, hold down the first two and at the same time press the third.
General Precautions TOSHIBA computers are designed to optimize safety, minimize strain and withstand the rigors of portability. However, certain precautions should be observed to further reduce the risk of personal injury, damage to the computer or impared performance. Be certain to read the general precautions below and to note the cautions included in the text of the manual. Stress injury Carefully read the Instruction Manual for Safety & Comfort.
TOSHIBA A100 Pressure or impact damage Do not apply heavy pressure to the computer or subject it to strong impact. Excessive pressure or impact can cause damage to computer components or otherwise cause malfunctions. PC card overheating Some PC cards can become hot with prolonged use. Overheating of a PC card can result in errors or instability in the PC card operation. Also be careful when you remove a PC card that has been used for a long time.
Chapter 1 Introduction This chapter provides an equipment checklist, and it identifies the computer’s features, options and accessories. Some of the features described in this manual may not function properly if you use an operating system that was not pre- installed by TOSHIBA. Equipment checklist Carefully unpack your computer. Save the box and packing materials for future use.
Introduction Software Windows Vista™ ■ The following software is preinstalled: ■ Microsoft® Windows Vista™ ■ Modem Driver ■ Display Drivers for Windows ■ Wireless LAN driver (Can be used only for Wireless LAN models) ■ Sound Driver for Windows ■ LAN Drivers ■ Bluetooth Driver (Can be used only for Bluetooth models) ■ Pointing Device Driver ■ Toshiba Value Added Package ■ TOSHIBA Power Saver ■ TOSHIBA User’s Manual ■ TOSHIBA Assist ■ TOSHIBA ConfigFree ■ TOSHIBA PC Diagnostic Tool ■ TOSHIBA Zooming Utility
Introduction Backup media and additional Software ■ Product Recovery DVD-ROM ■ Windows Anytime Upgrade DVD (provided in some regions) Features The computer uses TOSHIBA’s advanced Large Scale Integration (LSI), Comple-mentary Metal-Oxide Semiconductor (CMOS) technology extensively to provide compact size, minimum weight, low power usage, and high reliability.
Introduction Disks User’s Manual Hard disk drive The computer has an integrated, 2 1/2" hard disk drive (HDD) for nonvolatile storage of data and software. It comes in the following sizes. ■ 40 GB (37.26 billion bytes) ■ 60 GB (55.89 billion bytes) ■ 80 GB (74.52 billion bytes) ■ 100 GB (93.15 billion bytes) ■ 120 GB (111.78 billion bytes) ■ 160 GB (130.41 billion bytes) ■ 200 GB (186.
Introduction DVD Super Multi (+-R DL) drive Some models are equipped with a full-size DVD Super Multi (+- R DL) drive module that lets you record data to rewritable CD/DVDs as well as run either 12 cm (4.72") or 8 cm (3.15") CD/DVDs without using an adaptor. It reads DVD-ROMs at maximum 8 speed and CD-ROMs at maximum 24 speed. It writes CD-R at up to 24 speed, CD-RW at up to 16 speed, DVD-R at up to 8 speed and DVD-RW at maximum 6 speed and DVD-RAM at maximum 5 speed.
Introduction Graphics controller Graphics controller maximizes display performance. Refer to Appendix B for more information. Keyboard Built-in 85 keys or 86 keys, compatible with IBM® enhanced keyboard, embedded numeric overlay, dedicated cursor control, and keys. See Chapter 5, The Keyboard, for details. Pointing Device Built-in A Touch Pad and control buttons in the palm rest enable control of the on-screen pointer.
Introduction Slots PC card A PC card slot accommodates: One 5 mm Type II card Refer to Chapter 8, Optional Devices, for details Multiple Digital Media Card This slot lets you easily transfer data from devices, such as digital cameras and Personal Digital Assistants, that use flash memory (SD/MS/MS Pro/MMC/xD memory cards). (Provided with some models) Express card (depending on model purchased) This slot allows you to install a Express Card™/34 or Express Card™/54 to expand functionality.
Introduction User’s Manual Wireless LAN Some computers in this series are equipped with a Wireless LAN mini card that is compatible with other LAN systems based on Direct Sequence Spread Spectrum/Orthogonal Frequency Division Multiplexing radio technology that complies with the IEEE 802.11 Standard (Revision A, B and G). ■ Automatic Transmit Rate Select mechanism in the transmit range of 54, 48, 36, 24, 18, 12, 9 and 6 Mbit/s (Revision A/B, B/G, A/B/G combo type).
Introduction Security Security lock slot Connects an optional security lock to anchor the computer to a desk or other large object. Software Operating System Windows Vista™ is available. Refer to the preinstalled software section at the front of this chapter. TOSHIBA Utilities A number of utilities and drivers are preinstalled to make your computer more convenient to use. Refer to the Utilities section in this chapter.
Introduction User’s Manual Keypad overlay A ten-key pad is integrated into the keyboard. Refer to the Keypad overlay section in Chapter 5, The Keyboard, for instructions on using the keypad overlay. Power on password Two levels of password security, supervisor and user, are available to prevent unauthorized access to your computer. Instant security A hot key function blanks the screen and disables the computer providing data security.
Introduction Hibernation This feature lets you turn off the power without exiting from your software. The contents of main memory are saved to the hard disk, when you turn on the power again, you can continue working right where you left off. Refer to the Turning off the power section in Chapter 3, Getting Started, for details. Sleep If you have to interrupt your work, you can turn off the power without exiting from your software. Data is maintained in the computer’s main memory.
Introduction Utilities and Application This section describes preinstalled utilities and tells how to start them. For details on operations, refer to each utility’s online manual, help files or readme.txt files. TOSHIBA Assist TOSHIBA Assist is a graphical user interface that provides easy access to help and services. HW Setup To start the utility, click , point to All Programs, click TOSHIBA, click Utilities, and select HWSetup icon. DVD Video Player The DVD Video Player is used to play DVD-Video.
Introduction TOSHIBA ConfigFree ConfigFree is a suite of utilities to allow easy control of communication device and network connections. ConfigFree also allows you to find communication problems and create profiles for easy switching between location and communication networks. You can boot ConfigFree from the menu bar as follows. - All Programs - TOSHIBA - Networking ConfigFree Bluetooth TOSHIBA Stack This software enables communication between remote Bluetooth devices.
Introduction Options You can add a number of options to make your computer even more powerful and convenient to use. The following options are available: User’s Manual Memory expansion Two memory expansion slots are available for installing 256 MB, 512 MB, 1024 MB or 2048 MB memory modules. The modules are PC2-4200 or PC2-5300, 200-pin, SO Dual In-line (SO-DIMM).
Chapter 2 The Grand Tour This chapter identifies the various components of your computer. Become familiar with each component before you operate the computer. Front with the display closed Figure below shows the computer’s front with its display panel in the closed position.
The Grand Tour Headphone jack A standard 3.5 mm mini headphone jack enables connection of a stereo headphone (16 ohm minimum) or other device for audio output. When you connect headphones, the internal speaker is automatically disabled. Infrared receiver window Infrared receiver window is provided with some models. This is a sensor window that receives signals from the remote control which is provided with your computer. Not supported by a Windows Vista™ model.
The Grand Tour Be careful not to block the fan vent. Also be careful to keep foreign objects out of the vents. A pin or similar object can damage the computer’s circuitry. Video-out jack Plug a 4-pin S-Video connector into this jack. i.LINK (IEEE 1394) Port Connect an external device, such as a digital video camera to this port for high-speed data transfer. Some models are equipped with a i.LINK port.
The Grand Tour Right side Figure below shows the computer’s right side. Wireless communication switch USB Ports Security lock slot Optical Media Drive *Modem jack *The availability of Modem Jack is depending on the model you purchased. The right side of the computer Universal Serial Bus Ports The two Universal Serial Bus (USB) ports comply with USB Serial 2.0 standards, which enables data transfer speeds 40 times faster than the USB 1.1 standards. (The ports also support USB 1.
The Grand Tour Security lock slot A security cable attaches to this slot. The optional security cable anchors your computer to a desk or other large object to deter theft. Back side Figure below shows the computer’s back side. USB Ports LAN jack DC IN 15V The computer’s back side Universal Serial Bus Ports The two Universal Serial Bus (USB) ports comply with USB Serial 2.0 standards, which enables data transfer speeds 40 times faster than the USB 1.1 standards. (The ports also support USB 1.
The Grand Tour Underside Figure below shows the underside of the computer. Make sure the display is closed before turning over your computer. Battery pack Battery Release Latch Battery Pack Lock Memory module cover The underside of the computer User’s Manual Battery pack The battery pack powers the computer when the AC adaptor is not connected. The Batteries section in Chapter 6, Power and Power-Up Modes, describes how to access the battery pack.
The Grand Tour Front with the display open Figure below shows the front of the computer with the display open. To open the display, slide the display latch on the front of the computer and lift the display up. Position the display at a comfortable viewing angle.
The Grand Tour Stereo Speaker The speaker emits sound generated by your software as well as audio alarms, such as low battery condition, generated by the system. Touch Pad Moves the pointer and selects or activates items on the screen. Can be set to perform other mouse functions, such as scrolling, selecting, and doubleclicking. Touch Pad Control Buttons Function like the left and right buttons on an external mouse. Power Button Press the power button to turn the computer’s power on and off.
The Grand Tour System indicators Figure below shows the system indicators, which light when various computer operations are in progress. Multiple Digital Media card slot Disk DC IN Power Main battery Systems indicators Power source/system indicators User’s Manual DC IN The DC IN indicator glows blue when DC power is supplied from the AC power adaptor. If the adaptor’s output voltage is abnormal or if the power supply malfunctions, this indicator flashes amber.
The Grand Tour Keyboard indicators The figures below show the positions of the keypad overlay indicators and the CapsLock indicator. When the F10 key indicator glows the keypad overlay lets you control the cursor. When the F11 key indicator glows the keypad overlay lets you enter numbers. Numeric mode Arrow mode Keypad overlay indicators Arrow mode When the Arrow mode indicator lights green, you can use the keypad overlay (white labeled keys) as cursor keys.
The Grand Tour USB diskette drive A 3 1/2" diskette drive accommodates 1.44-megabyte or 720-kilobyte diskettes. It connects to the USB port. Disk-In-Use Indicator Diskette slot Eject button USB diskette drive Disk-In-Use Indicator This indicator lights when the diskette is being accessed. Diskette slot Insert diskette in this slot. Eject button When a diskette is fully seated in the drive, the eject button pops out.
The Grand Tour Region codes for DVD drives and media CD-RW/DVD-ROM, DVD-ROM, DVD Super Multi (+-R DL) drive and media are manufactured according to the specifications of six marketing regions. When you purchase DVD-Video, make sure it matches your drive, otherwise it will not play properly.
The Grand Tour DVD-ROM drive The full- size DVD-ROM drive module lets you record data to rewritable CD/DVDs as well as run either 12 cm (4.72") or 8 cm (3.15") CD/DVDs without using an adaptor. The read speed is slower at the center of a disc and faster at the outer edge. DVD read 8 speed (maximum) CD read 24 speed (maximum) CD-RW/DVD-ROM drive The full-size CD-RW/DVD-ROM drive module lets you record data to rewritable CDs as well as run either 12 cm (4.72") or 8 cm (3.
The Grand Tour AC adaptor The AC adaptor converts AC power to DC power and reduces the voltage supplied to the computer. It can automatically adjust to any voltage from 100 to 240 volts and to a frequency of either 50 or 60 hertz, enabling you to use the computer in almost any region. To recharge the battery, simply connect the AC adaptor to a power source and the computer. See Chapter 6 Power and Power-Up Modes for details.
Chapter 3 Getting Started This chapter provides basic information to get you started using your computer. It covers the following topics: Be sure also to read Instruction Manual for Safety & Comfort. This guide, which is included with the computer, explains product liability.
Getting Started Connecting the AC adaptor Attach the AC adaptor when you need to charge the battery or you want to operate from AC power. It is also the fastest way to get started, because the battery pack will need to be charged before you can operate from battery power. The AC adaptor can be connected to any power source supplying from 100 to 240 volts and 50 or 60 hertz. For details on using the AC adaptor to charge the battery pack, refer to Chapter 6, Power and Power-Up Modes.
Getting Started When you open the display, hold it with both hands and lift up slowly. Display latch Opening the display panel Turning on the power This section describes how to turn on the power. After you turn on the power for the first time, do not turn it off until you have set up the operating system (OS) and the OS has started up. 1. If the external diskette drive is connected, make sure it is empty. If a diskette is in the drive, press the eject button and remove the diskette. 2.
Getting Started Starting up for the first time When you first turn on the power, the computer’s initial screen is the Microsoft® Windows Vista™ Startup Screen Logo. Follow the on-screen directions. Turning off the power The power can be turned off in one of the following modes: Shut down (Boot), Hibernation or Sleep mode. Shut Down mode (Boot mode) When you turn off the power in Shut Down mode, no data is saved and the computer will boot to the operating system’s main screen. 1.
Getting Started For the computer to shut down in hibernation mode, the hibernation feature must be enabled in two places: the Hibernate tab in Power Options and Setup Action tab in TOSHIBA Power Saver. Otherwise, the computer will shut down in Sleep mode. If battery power becomes depleted, data saved in Sleep mode will be lost. ■ You can return to your previous working environment immediately when you turn on the computer.
Getting Started Sleep mode In sleep mode the power remains on, but the CPU and all other devices are in sleep mode. 1. Before entering Sleep mode, be sure to save your data. 2. Do not install or remove a memory module while the computer is in sleep mode. The computer or the module could be damaged. 3. Do not remove the battery pack while the computer is in sleep mode (unless the computer is connected to an AC power source). Data in memory will be lost.
Getting Started Restarting the computer Certain conditions require that you restart the computer system. For example, if: ■ You change certain computer settings. ■ An error occurs and the computer does not respond to your keyboard commands. There are three ways to restart the computer system: 1. Click Windows Start button , point to located in the power management button , and then click Restart. 2.
Getting Started Restoring the preinstalled software from the Product Recovery Media If preinstalled files are damaged, use the Product Recovery Media to restore them. To restore the operating system and all preinstalled software, follow the steps below. When you reinstall the Windows operating system, the hard disk will be reformatted and all data will be lost. 1. Load the Product Recovery Media in the drive and turn off the computer’s power. 2. Hold down the F12 key and turn on the power.
Chapter 4 Operating Basics This chapter gives information on basic operations including using the Touch Pad/Dual Mode Pad, USB diskette drive, optical media drives, the microphone, the internal modem, wireless communication and LAN. It also provides tips on caring for your computer, diskettes and CD/DVDs. Using the Touch Pad To use the Touch Pad, simply touch and move your finger tip across it in the direction you want the on-screen pointer to go.
Operating Basics Touch Pad Touch Pad Control Buttons Touch Pad and Touch Pad control buttons Using the USB diskette drive A 3 1/2" diskette drive connects to the computer’s USB port. It accommodates 1.44-megabyte or 720-kilobyte diskettes. Refer to Chapter 2, The Grand Tour, for more information. Connecting 3 1/2" diskette drive To connect the drive, plug the diskette drive connector into a USB port. Refer to figure below. Make sure the connector is right side up and properly aligned with the socket.
Operating Basics Disconnecting 3 1/2" diskette drive When you have finished using the diskette drive, follow the procedures below to disconnect it: 1. Wait for the indicator light to go out to make sure all diskette activity has stopped. If you disconnect the diskette drive or turn off the power while the computer is accessing the drive you may lose data or damage the diskette or the drive. 2. Click the Safely Remove Hardware icon on the system tray. 3. Click Diskette drive. 4.
Operating Basics Loading discs To load CD/DVDs, follow the steps below and refer to figures 4-3 to 4-7. 1. a. When the power is on, press the DVD-ROM eject button to open the drawer slightly. Eject button Pressing the DVD-ROM eject button b. Pressing the eject button will not open the drawer when the DVD-ROM drive’s power is off.
Operating Basics 2. Grasp the drawer gently and pull until it is fully opened. Pulling the drawer open 3. Lay the CD/DVD, label side up, in the drawer. Inserting a CD/DVD When the drawer is fully opened, the edge of the computer will extend slightly over the CD/DVD tray. Therefore, you will need to turn the CD/DVD at an angle when you place it in the tray. After seating the CD/DVD, however, make sure it lies flat, as shown in figure above. 1. Do not touch the laser lens.
Operating Basics 4. Push the center of the drawer to close it. Press gently until it locks into place. If the CD/DVD is not seated properly when the drawer is closed, the CD/ DVD might be damaged. Also, the drawer might not open fully when you press the eject button. Closing the DVD-ROM drawer Removing discs To remove the CD/DVD, follow the steps below and refer to figure above. Do not press the eject button while the computer is accessing the DVD-ROM drive.
Operating Basics Removing a CD/DVD 3. Push the center of the drawer to close it. Press gently until it locks into place. AV Button function (Provided with some models) This section describes a button function.
Operating Basics Writing CDs on CD-RW/DVD-ROM drive You can use the CD-RW/DVD-ROM drive to write data to either CD-R or CD-RW discs. The following applications for writing are supplied: TOSHIBA Disc Creator. CD-R discs can be written to only once. CD-RW discs can be rewritten many times. Important message (CD-RW/DVD-ROM drive) Before you write or rewrite to CD-RW disc, read and follow all setup and operating instructions in this section.
Operating Basics ■ Do not write while virus check software is running. Wait for it to finish, then disable virus detection programs including any software that checks files automatically in the background. ■ Do not use hard disk utilities, including those intended to enhance HDD access speed. They may cause unstable operation and damage data. ■ Write from the computer’s HDD to the CD. Do not try to write from shared devices such as a LAN server or any other network device.
Operating Basics ■ Damage that may be caused by using third party equipment or software. Given the technological limitations of current optical disc writing drives, you may experience unexpected writing or rewriting errors due to disc quality or problems with hardware devices. Also, it is a good idea to make two or more copies of important data, in case of undesired change or loss of the recorded contents.
Operating Basics DVD+R MITSUBISHI KAGAKU MEDIA CO., LTD Ricoh Co., Ltd. DVD-RW DVD Specifications for Recordable Disc for Version 1.1 VICTOR COMPANY OF JAPAN, LIMITED MITSUBISHI KAGAKU MEDIA CO., LTD DVD+RW MITSUBISHI KAGAKU MEDIA CO., LTD Ricoh Co., Ltd. DVD-RAM DVD Specifications for DVD-RAM Disc for Version 2.0, Version 2.1 or Version 2.2 Matsushita Electric Industrial Co., Ltd. Hitachi Maxell Ltd. DVD+R DL MITSUBISHI KAGAKU MEDIA CO., LTD. DVD-R DL MITSUBISHI KAGAKU MEDIA CO., LTD.
Operating Basics ■ DVD-RAM formatted by FAT32 cannot be read in Windows 2000 without DVD-RAM Driver Software. ■ When multiple drives that can write data to discs are connected, be careful not to write to the wrong drive. ■ Be sure to connect the universal AC adaptor before you write or rewrite. ■ Before you enter sleep/hibernation mode, be sure to finish DVD-RAM writing. Writing is finished if you can eject DVD-RAM media. ■ Be sure to close all other software programs except the writing software.
Operating Basics ■ Keep mobile phones and other wireless communication devices away from the computer. ■ Always copy data from the HDD to the DVD-RAM. Do not use cut-andpaste. The original data will be lost if there is a write error. Disclaimer (DVD Super Multi (+-R DL) drive) TOSHIBA does not bear responsibility for the following: ■ Damage to any CD-R/RW or DVD-R/-R DL/-RW/+R/+R DL/+RW/ DVD-RAM disc that may be caused by writing or rewriting with this product.
Operating Basics ■ If you add data to a DVD-R/-R DL and DVD+R/+R DL disc that you have already recorded to, you might not be able to read the added data under some circumstances. It cannot be read in 16-bit operating systems, such as Win-dows 98 SE and Windows ME. In Windows NT 4, you will need Service Pack 6 or later to read added data. In Windows 2000, you will need Service Pack 2 or later to read it. Some DVD-ROM and CD-RW/DVD-ROM drives cannot read added data regardless of the operating system.
Operating Basics When using Ulead DVD MovieFactory® for TOSHIBA: How to make a DVD-Video Simplified steps for making a DVD-Video from video data captured from a DV-Camcorder: 1. Click - All Programs - DVD MovieFactory for TOSHIBA - Ulead DVD MovieFactory for TOSHIBA Launcher to launch DVD MovieFactory. 2. Insert a DVD-RW or DVD+RW disc in Burner. 3. Click Video Disc - Burn Video to Disc to launch Direct Recording dialog box, choose DVD-Video/+VR to invoke Straight Capture to Disc Page. 4.
Operating Basics ■ Do not operate DVD MovieFactory immediately after turning on the computer. Please wait until all Disc Drive activity has stopped. ■ When recording to a DV-Camcorder, to ensure you capture all of your data, let the camcorder record for a few seconds before you begin recording your actual data. ■ CD recorder, JPEG functions, DVD-Audio, mini DVD, and Video CD functions are not supported in this version. ■ While recording video to DVD, please close all other programs.
Operating Basics Media care This section provides tips on protecting data stored on your CD/DVDs and diskettes. Handle your media with care. The following simple precautions will increase the lifetime of your media and protect the data stored on them: CD/DVDs 1. Store your CD/DVDs in the container they came in to protect them and keep them clean. 2. Do not bend the CD/DVD. 3. Do not write on, apply a sticker to, or otherwise mark the surface of the CD/DVD that contains data. 4.
Operating Basics Modem (Provided with some models) The availability of this feature is depending on the model you purchased. This section describes how to connect and disconnect the internal modem to and from a telephone jack. The internal modem does not support voice functions. All data and fax functions are supported. ■ In case of a lightning storm, unplug the modem cable from the telephone jack. ■ Do not connect the modem to a digital telephone line. A digital line will damage the modem.
Operating Basics Properties menu Click the icon with the secondary mouse button to display the following menu. The menu list (Windows Vista™) Setting You can enable or disable the following settings: AutoRun Mode The Region Select utility starts automatically when you start up the operating system. Open the Dialing Properties dialog box after selecting region. The dialing properties dialog box will be displayed automatically after you select the region. Location list for region selection.
Operating Basics Connecting To connect the internal modem cable, follow the steps below. 1. Plug one end of the modular cable into the modem jack. 2. Plug the other end of the modular cable into a telephone jack. Telephone Jack Modem Jack Connecting the internal modem Do not pull on the cable or move the computer while the cable is connected.
Operating Basics Supported features. It supports the following features: ■ Automatic Transmit Rate Select mechanism in the transmit range of 54, 48, 36, 24, 18, 12, 9 and 6 Mbit/s (Revision A and G, Revision A/B, B/G, A/B/G combo type). ■ Automatic Transmit Rate Select mechanism in the transmit range of 11, 5.5, 2 and 1 Mbit/s (Revision B). ■ Frequency Channel Selection (Revision A/Turbo Mode: 5 GHz, Revision B/G: 2.
Operating Basics Wireless communication switch You can enable or disable Wireless LAN and Bluetooth functions, with the on/off switch. No transmissions are sent or received when the switch is off. Slide the switch toward the left of the computer to turn it on and toward the right of the computer to turn it off. Set the switch to off in airplanes and hospitals. Check the indicator. It will stop glowing when the wireless communication function is off.
Operating Basics Connecting LAN cable The computer must be configured properly before connecting to a LAN. Logging onto a LAN using the computer’s default settings could cause a malfunction in LAN operation. Check with your LAN administrator regarding set-up procedures. If you are using Fast Ethernet LAN (100 megabits per second, 100BASE-TX), be sure to connect with a category 5 cable, CAT5, or higher.
Operating Basics Cleaning the computer To help ensure long, trouble-free operation, keep the computer free of dust and use care with liquids around the computer. ■ Be careful not to spill liquids into the computer. If the computer does get wet, turn the power off immediately and let the computer dry completely before you turn it on again. ■ Clean the computer using a slightly damp (with water) cloth. You can use glass cleaner on the display.
Operating Basics Heat dispersal To protect from overheating, the CPU has an internal temperature sensor. If the computer’s internal temperature rises to a certain level, the cooling fan is turned on or the processing speed is lowered. You can select whether to control the CPU temperature by turning on the fan first, then if necessary, lowering the CPU speed. Or, by lowering the CPU speed first, then if necessary, turning on the fan.
Chapter 5 The Keyboard The computer’s keyboard layouts are compatible with a 101/102-key enhanced keyboard. By pressing some keys in combination, all the 101/ 102-key keyboard functions can be executed on the computer. The number of keys on your keyboard depends on which country/region’s keyboard layout your computer is configured with. Keyboards for numerous languages are available. There are five types of keys: typewriter keys, keypad overlay, function keys, soft keys and cursor control keys.
The Keyboard F1 ... F12 function keys The function keys, not to be confused with Fn, are the 12 keys at the top of your keyboard. These keys are dark gray, but function differently from the other dark gray keys. F1 through F12 are called function keys because they execute programmed functions when pressed. Used in combination with the Fn key, keys marked with icons execute specific functions on the computer. See the section, Soft keys: Fn key combinations, in this chapter.
The Keyboard Press Fn + Enter to simulate Enter on the enhanced keyboard’s numeric keypad. Press Fn + Ctrl to simulate the enhanced keyboard’s right Ctrl key. Press Fn + Alt to simulate the enhanced keyboard’s right Alt key. Hot keys Hot keys (Fn + a function or Esc key) let you enable or disable certain features of the computers. Sound mute: Pressing Fn + Esc in a Windows environment turns sound on or off. When you press these hot keys, the current setting will be displayed as an icon.
The Keyboard Display selection: Press Fn + F5 to change the active display device. When you press these hot keys a dialog box appears. Only selectable devices will be displayed. Hold down Fn and press F5 again to change the device. When you release Fn and F5, the selected device will change. If you hold down the keys for three seconds the selection will return to LCD. Display Brightness: Pressing Fn + F6 decreases the display brightness in increments.
The Keyboard TOSHIBA Zooming Utility (reduce): To reduce the icon size on the desktop or the application window, press the 1 key while holding down the Fn key. TOSHIBA Zooming Utility (enlarge): To enlarge the icon size on the desktop or the application window, press the 2 key while holding down the Fn key. Fn Sticky key You can use the Toshiba Accessibility Utility to make the Fn key sticky, that is, you can press it once, release it, and they press an "F number" key.
The Keyboard Arrow mode To turn on the Arrow mode, press Fn + F10. The Arrow mode indicator lights. Now try cursor and page control using the keys shown in figure above. Press Fn + F10 again to turn off the overlay. Numeric mode To turn on the Numeric mode, press Fn + F11. The Numeric mode indicator lights. Now try numeric data entry using the keys in figure above. Press Fn + F11 again to turn off the overlay.
The Keyboard Temporarily using overlay (overlay off) While using the normal keyboard, you can temporarily use the keypad overlay without turning it on: 1. Press and hold down Fn. 2. Check the keyboard indicators. Pressing Fn turns on the most recently used overlay. If the Numeric mode indicator lights, you can use the overlay for numeric entry. If the Arrow mode indicator lights, you can use the overlay for cursor and page control. 3. Release Fn to return to normal keyboard operation.
Chapter 6 Power and Power-Up Modes The computer’s power resources include the AC adaptor and internal batteries. This chapter gives details on making the most effective use of these resources including charging and changing batteries, tips for saving battery power, and power up modes.
Power and Power-Up Modes Power on AC adaptor Battery charge is • above low not • connected battery trigger point Battery charge is • below low battery • trigger point Power off (no operation) Operates LED: Battery off DC IN off Operates LED: Battery flashes Amber DC IN off Battery charge is Computer goes into exhausted Hibernation or shuts down (depending on the Toshiba power Management Utility Setting) No battery installed • • No operation LED: Battery off DC IN off Power indicators The Battery, DC
Power and Power-Up Modes DC IN indicator Check the DC IN indicator to determine the power status with the AC adaptor connected: Blue Indicates the AC adaptor is connected and supplying proper power to the computer. Amber Indicates a problem with the power supply. Plug the AC adaptor into another outlet. If it still does not operate properly, see your dealer. No light Under any other conditions, the indicator does not light. Power indicator Check the Power indicator to determine the power status.
Power and Power-Up Modes The following message appears when you turn on the power: ERRPR 0271:Check date and time settings. WARNING 0251:System CMOS checksum bad Default configuration used. Press to resume, to Setup. To ensure that the battery pack maintains its maximum capacity, operate the computer on battery power at least once a month until the battery pack is fully discharged. Refer to Extending battery life in this chapter for procedures.
Power and Power-Up Modes Danger 1. Never try to dispose of the battery pack by burning or expose it to a heating device such as a microwave oven. The battery pack could explode and cause bodily injury. 2. Never try to disassemble, repair or otherwise tamper with a battery pack. The battery pack will overheat and ignite. Leakage of caustic alkaline solution or other electrolytic substances will cause fire or injury, possibly resulting in death or serious injury. 3.
Power and Power-Up Modes 3. Make sure the battery is securely installed in the computer before attempting to charge the battery pack. Improper installation could generate smoke or fire, or cause the battery pack to rupture. 4. Keep the battery pack out or reach of infants and children. It can cause injury. Caution 1. Never continue to use a battery pack after its recharging capacity has become impaired, or after the display of a warning message indicating that the battery pack’s power is exhausted.
Power and Power-Up Modes Charging the batteries When the power in the battery pack becomes low, the Battery indicator flashes amber indicating that only a few minutes of battery power remain. If you continue to use the computer while the Battery indicator flashes, the computer enables Hibernation mode (so you don’t lose data) and automatically turns off.
Power and Power-Up Modes ■ The battery is nearly completely discharged. Leave the AC adaptor connected for a few minutes and the battery should begin charging. The Battery indicator may show a rapid decrease in battery operating time when you try to charge a battery under the following conditions: ■ The battery has not been used for a long time. ■ The battery has completely discharged and been left in the computer for a long time. ■ A cool battery is installed in a warm computer.
Power and Power-Up Modes ■ ■ ■ ■ ■ ■ ■ ■ ■ Screen brightness ■ Cooling Method ■ System Sleep ■ System Hibernation ■ Monitor Power off ■ HDD Power off How often and how long you use the hard disk, CD/DVD-ROM drive and the diskette drive. How much charge the battery contained to begin with. How you use optional devices, such as a PC card, to which the battery supplies power. Enabling Resume mode conserves battery power if you are frequently turning the computer off and on.
Power and Power-Up Modes 3. Operate the computer on battery power for five minutes. If the battery pack has at least five minutes of operating time, continue operating until the battery pack is fully discharged. If the battery LED flashes or there is some other warning to indicate a low battery, go to step 4. 4. Connect the AC adaptor to the computer and the power cord to a power outlet.
Power and Power-Up Modes 4. Turn the computer upside down with the back of the computer facing you. 5. Slide the battery pack locking latch toward the unlock position. Battery Pack Lock Battery Pack Battery Release Latch Slide the locking latch to the unlocked position 6. Slide the battery release latch to free the battery pack for removal, then lift up the battery pack. Battery Pack Lock Battery Release Latch Battery Pack Removing the battery pack 7. Pull the battery pack forward to remove it.
Power and Power-Up Modes Installing the battery pack To install a battery pack, follow the steps below. The battery pack is a lithium ion battery, which can explode if not properly replaced, used, handled or disposed of. Dispose of the battery as required by local ordinances or regulations. Use only batteries recommended by TOSHIBA as replacements. 1. Be sure the computer’s power is off and all cables are disconnected. 2. Insert the battery pack. Battery pack Installing the battery pack 3.
Power and Power-Up Modes Power-up modes The computer has the following power-up modes: ■ Boot: Computer shuts down without saving data. Always save your work before you turn the computer off in boot mode. ■ Hibernation: Data in memory is saved to the hard disk. ■ Sleep: Data is maintained in the computer’s main memory. Refer also to the sections Turning on the power and Turning off the power in Chapter 3, Getting Started. Windows utilities You can specify the setting in TOSHIBA Power Saver.
Chapter 7 HW Setup and Passwords This chapter explains how to use TOSHIBA HW Setup program to configure your computer and how to set passwords. HW Setup TOSHIBA HW Setup lets you configure settings for pointing devices, display, CPU, boot priority, keyboard, USB, LAN, general, password, and device config. If the supervisor password is set, access to the TOSHIBA HW Setup program can be prevented when the user password is used to log on to the computer.
HW Setup and Passwords General This window displays the BIOS version and contains two buttons: Default and About. Default Return all HW Setup values to the factory settings. About Display the HW Setup version. Setup This field displays BIOS Version and date. Password User Password This option allows you to set or reset the user password for power on. Not Registered Change or remove the password. (Default) Registered Set the password. A dialogue box will appear to let you set the password.
HW Setup and Passwords 2. Enter the currently registered password. The character string you enter is displayed as a string of asterisks. Enter Password: **** If you click the OK button before entering the password, Registered will appear on the display. 3. Click the OK button. If the character string you enter matches the registered password, the password option is reset and the display changes to: Not registered If they do not match, the following message appears. You must repeat step 1.
HW Setup and Passwords Boot Priority Boot Priority Options This option sets the priority for booting the computer. You can override the settings and manually select a boot device by pressing one of the following keys while the computer is booting: U Selects the USB diskette drive. N Selects the Network. 1 Selects the primary HDD. C Selects the CD-ROM*. This procedure does not affect the settings. * In this computer, CD-ROM refers to the DVD-ROM, CD-R/RW or CD-RW/DVD-ROM drives.
HW Setup and Passwords Keyboard Wake-up on Keyboard When this feature is enabled and the computer is in sleep mode, you can turn on the computer by pressing any key. It is effective only for the internal keyboard and only when the computer is in sleep mode. Enabled Enables Wake-up on Keyboard. Disabled Disables Wake-up on Keyboard. (Default) USB Legacy USB Support Use this option to enable or disable USB Legacy Emulation.
Chapter 8 Optional Devices Optional devices can expand the computer’s capabilities and its versatility.
Optional Devices PC cards The computer is equipped with a PC card expansion slot that can accommodate one 5 mm Type II card. Any PC card that meets industry standards (manufactured by TOSHIBA or other vendor) can be installed. The slots support 16-bit PC cards, including PC card 16’s multifunction card and CardBus PC cards. CardBus supports the new standard of 32-bit PC cards. The bus provides superior performance for the greater demands of multimedia data transmission.
Optional Devices Removing a PC card To remove the PC card, follow the steps below. 1. In Windows Vista™, open the Safely Remove Hardware icon on the system tray and disable the PC card. 2. Press the eject button of the PC card you want to remove to extend the button. 3. Press the extended eject button to pop the card out slightly. 4. Grasp the PC card and remove it.
Optional Devices 3. Check the configuration in the HW Setup window to make sure it is appropriate for your card. Express Card slot Inserting the Express Card Removing an Express Card To remove the Express Card, follow the steps below. 1. In Windows Vista™, open the Safely Remove Hardware icon on the system tray and disable the Express Card. 2. Press the Express Card slightly to make it stretch out. 3. Grasp the Express Card and pull it out from the slot.
Optional Devices Multiple Digital Media Card Slot The computer is equipped with a Multiple Digital Media Card Slot that can accommodate Secure Digital (SD)/Memory Stick (MS)/Memory Stick Pro (MS Pro)/Multi Media Card (MMC)/xD memory cards. These memory cards let you easily transfer data from devices, such as digital cameras and Personal Digital Assistants, that use SD/MS/MS Pro/MMC/xD memory cards. Keep foreign objects out of the Multiple Digital Media Cards Slot.
Optional Devices Make sure the SD/MS/MS Pro/MMC/xD card is oriented properly before you insert it. ■ Memory Stick Duo/Memory Stick Pro Duo/Mini SD card is not supported. ■ Two kinds of cards will not work at the same time. Please insert only one card when using Multiple Digital Media Card Slot. ■ Do not format a memory card with Windows as it might result in that card not being able to be used with some peripheral devices. If Windows fail to read the SD/MS/MS Pro/MMC/xD card, remove it then reinsert it.
Optional Devices Memory expansion You can install additional memory in the computer’s memory module to increase the amount of RAM. Only memory modules with the following parts numbers can be installed: ■ 256MB: PA3389U-1M25 ■ 512MB: PA3412U-1M51 ■ 1GB: PA3411U-1M1G Installing memory module To install a memory module, make sure the computer is in boot mode then: 1. Turn the computer off in boot mode. Refer to the Turning off the power section in Chapter 3.
Optional Devices Removing the cover 6. Insert the memory module into the connector on the computer. Press the module carefully and firmly to ensure a solid connection. 7. Push the module down so that it lies flat and is secured by two latches. Do not touch the connectors on the memory module or on the computer. Debris on the connectors may cause memory access problems. Inserting the memory module 8. Seat the cover and secure it with one screw. 9.
Optional Devices Removing memory module To remove the memory module, make sure the computer is in boot mode then: 1. Turn the computer off and remove all cables connected to the computer. ■ If you use the computer for a long time, the memory modules will become hot. In this case, let the memory modules cool to room temperature before you replace them. ■ Do not try to remove a memory module with the computer turned on or turned off in Sleep and Hibernation mode.
Optional Devices Additional battery pack (6 Cell, 9 Cell and 12 Cell) You can increase the portability of the computer with additional battery packs (6 Cell: PA3399U-2BAS/PA3399U-2BRS, 9 Cell: PA3478U-1BAS/ PA3478U-1BRS, 12 Cell: PA3400U-1BAS/PA3400U-1BRS). If you’re away from an AC power source, you can replace a low battery with a fully charged one. See Chapter 6, Power and Power-Up Modes.
Optional Devices If you have selected Simultaneous under the Display options of the HW Setup, both the external monitor and the internal LCD will be active when you turn on the computer. If Auto-Selected is selected, only the external monitor will be active. To change the display settings, press Fn + F5. If you disconnect the monitor before you turn the computer off, be sure to press Fn + F5 to switch to the internal display.
Optional Devices Precautions 1. Make a back-up of your data before transferring it to the computer. There is a possibility that the original data will be damaged. There is a particular risk that some frames will be deleted in the case of digital video transfer. TOSHIBA assumes no liability for such loss of data. 2. Do not transfer data in areas where static electricity is easily generated or in areas subjected to electronic noise. Data can be destroyed. 3.
Optional Devices Disconnecting 1. Open the Safety Remove Hardware icon on the Task Bar. 2. Point to i.LINK (IEEE1394) device and click. 3. Disconnect the cable from the computer then from the i.LINK device. Refer also to the documentation that came with your i.LINK device. Security lock A security lock enables you to anchor your computer to a desk or other heavy object to help prevent unauthorized removal of the computer.
Chapter 9 Troubleshooting TOSHIBA designed the computer for durability. However, should problems occur, following the procedures in this chapter can help to determine the cause. All readers should become familiar with this chapter. Knowing what might go wrong can help prevent problems from occurring. Problem solving process Resolving problems will be much easier if you observe the following guidelines: ■ Stop immediately when you recognize a problem exists. Further action may result in data loss or damage.
Troubleshooting ■ Make sure all options are set properly in the setup program. ■ Check all cables. Are they correctly and firmly attached? Loose cables can cause signal errors. ■ Inspect all connecting cables for loose wires and all connectors for loose pins. ■ Check that your diskette is correctly inserted and that the diskette’s write protect tab is correctly set. Make notes of your observations and keep them in a permanent error log. This will help you describe your problems to your dealer.
Troubleshooting Hardware and system checklist This section discusses problems caused by your computer’s hardware or attached peripherals.
Troubleshooting Turn off the computer and check all cable connections. If the test fails again, contact your dealer. Power When the computer is not plugged into an AC adaptor, the battery pack is the primary power source. However, your computer has a number of other power resources, including intelligent power supply and Real Time Clock battery. These resources are interrelated and any one could affect apparent power problems. This section provides check lists for AC adaptor and the main battery.
Troubleshooting Battery If you suspect a problem with the battery, check the DC IN indicator as well as the battery indicator. For information on indicators and battery operation see Chapter 6, Power and Power-Up Modes. Problem Procedure Battery doesn’t power the computer Battery doesn’t charge when the AC adaptor is attached (Battery indicator does not glow amber.) The battery may be discharged. Connect the AC adaptor to charge the battery.
Troubleshooting Keyboard Keyboard problems can be caused by your setup configuration. For more information refer to Chapter 5, The Keyboard and Chapter 7, HW Setup and Passwords. Problem Procedure Some letter keys produce numbers Check that the numeric keypad overlay is not selected. Press Fn + F10 and try typing again. Output to screen is garbled Make sure the software you are using is not remapping the keyboard. Remapping involves reassigning the meaning of each key.
Troubleshooting Problem Procedure Slow performance Your files may be fragmented. Run SCANDISK and defragmenter to check the condition of your files and disk. Refer to your OS documentation or online HELP for information on running SCANDISK and the defragmenter. As a last resort, reformat the hard disk. Then, reload the operating system and other files. If problems persist, contact your dealer. DVD-ROM drive For more information, refer to Chapter 4, Operating Basics.
Troubleshooting CD-RW/DVD-ROM drive For more information, refer to Chapter 4, Operating Basics. Problem Procedure You cannot access a CD/DVD in the drive Make sure the drive’s drawer is securely closed. Press gently until it clicks into place. Open the drawer and make sure the CD/DVD is properly seated. It should lie flat with the label facing up. A foreign object in the drawer could block laser light from reading the CD or DVD. Make sure there is no obstruction. Remove any foreign object.
Troubleshooting Problem Procedure Cannot write correctly If you have trouble writing, make sure you are observing the following precautions: ■ Use only media recommended by TOSHIBA ■ Do not use the mouse or keyboard during writing. ■ Use only the software supplied with the computer for recording. ■ Do not run or start other software during writing. ■ Do not jar the computer during writing. ■ Do not connect/disconnect external devices or install/remove internal cards during writing.
Troubleshooting Problem Procedure Some CD/DVDs run correctly, but others do not The software or hardware configuration may be causing a problem. Make sure the hardware configuration matches your software’s needs. Check the CD/DVD’s documentation. Check the type of DVD/CD you are using.
Troubleshooting Diskette drive For more information, refer to Chapter 4, Operating Basics. Problem Procedure Drive does not operate There may be a faulty cable connection. Check the connection to the computer and to the drive. Some programs run correctly but others do not The software or hardware configuration may be causing a problem. Make sure the hardware configuration matches your software needs. You cannot access the external 3 1/2" diskette drive Try another diskette.
Troubleshooting Problem Procedure When the reaction of Touch pad is sensitive to slow Adjust the touch Sensitivity. 1. Open the Control Panel. 2. Click the Printers icon and then the Other Hardware icon. 3. Click the Mouse icon. 4. Click the Device Setting tab. 5. Click the Setting button. 6. The Properties for Synaptics Touchpad on PS/ 2 port screen appears. Double-click Sensitivity in the Select an item section on the left side of the screen. 7. PalmCheck and Touch Sensitivity are displayed.
Troubleshooting Problem Procedure The mouse pointer moves erratically The mouse might be dirty. Refer to your mouse documentations for instructions on cleaning. If problems persist, contact your dealer. PC card Refer also to Chapter 4, Operating Basics. Problem Procedure PC card error occurs Reseat the PC card to make sure it is firmly connected. Make sure the connection between the external device and the card is firm. Check the card’s documentation. If problems persist, contact your dealer.
Troubleshooting Problem Procedure Display error occurs Check that the cable connecting the external monitor to the computer is attached firmly. If problems persist, contact your dealer. Sound system Problem No sound is heard Procedure Adjust the volume control dial. Check the software volume settings. Make sure the headphone connection is secure. Check Windows Device Manager.
Troubleshooting USB Refer also to your USB device’s documentation. Problem Procedure USB device does not work Check for a firm cable connection between the USB ports on the computer and the USB device. Make sure the USB device drivers are properly installed. Refer to your Windows documentation for information on checking the drivers. If you are using an operating system that does not support USB, you can still use a USB mouse and/ or USB keyboard.
Troubleshooting Problem Procedure A CONNECT display is quickly replaced by NO CARRIER Check the error control setting in your communications application. You can also use the AT\N command. Refer to the chapter on AT commands in online help files for Appendix C, AT Commands. Character display becomes garbled during a communication In data transmission, make sure the parity bit and stop bit settings correspond with those of the remote computer. Check the flow control and communication protocol.
Troubleshooting Wireless LAN If the following procedures do not restore LAN access, consult your LAN administrator. For more information on wireless communication, refer to Chapter 4, Operating Basics. Problem Procedure Cannot access Wireless LAN Make sure the computer’s wireless communication switch is set to on. If problems persist, consult your LAN administrator. Bluetooth For more information on wireless communication, refer to Chapter 4, Operating Basics.
Troubleshooting TOSHIBA support If you require any additional help using your computer or if you are having problems operating the computer, you may need to contact TOSHIBA for additional technical assistance. Before you call Some problems you experience may be related to software or the operating system, it is important to investigate other sources of assistance first. Before contacting TOSHIBA, try the following: ■ Review troubleshooting sections in the documentation for software and peripheral devices.
Chapter 10 Disclaimers This chapter slates the Disclaimer(s) information applicable to TOSHIBA computers. CPU Central Processing Unit ("CPU") Performance Disclaimer.
Disclaimers Under some conditions, your computer product may automatically shutdown. This is a normal protective feature designed to reduce the risk of lost data or damage to the product when used outside recommended conditions. To avoid risk of lost data, always make back-up copies of data by periodically storing it on an external storage medium. For optimum performance, use your computer product only under recommended conditions. Read additional restrictions in your product documentation.
Disclaimers HDD Drive Capacity 1 Gigabyte (GB) means 109 = 1,000,000,000 bytes using powers of 10. The computer operating system, however, reports storage capacity using powers of 2 for the definition of 1 GB = 230 = 1,073,741,824 bytes, and therefore shows less storage capacity. Available storage capacity will also be less if the product includes one or more pre-installed operating systems, such as Microsoft Windows and/or pre-installed software applications, or media content.
Disclaimers SRS SRS audio enhancements are available in the Microsoft Windows operation system only. LCD Brightness and Eye Strain Your LCD display has a brightness approaching that of a TV device. We recommend that you adjust the brightness of your LCD to a comfortable level to prevent possible strain on your eyes.
Appendix A Specifications This appendix summarizes the computer’s technical specifications. Physical Dimensions Size With TFT display 360 (w) × 267 (d) × 29.8 (front) / 36.8 (rear) millimeters Weight (typical*) < 3 kilograms, configured with: 15.4" panel, DVD Combo drive, 6-cell battery, and modem. * Weight will vary depending on whether or not and what kind of options are adopted.
Specifications Power Requirements AC adaptor 100- 240 volts AC 50 or 60 hertz (cycles per second) Computer 15 VDC 5.0 amperes/6.0 amperes Built-in Modem The ability of this feature is depending on the model you purchased.
Specifications User’s Manual Communication speed Data transmission and reception 300/1200/2400/4800/7200/9600/12000/14400/ 16800/19200/21600/24000/26400/28800/31200/ 33600 bps Data reception only with V.90 28000/29333/30666/32000/33333/34666/36000/ 37333/38666/40000/41333/42666/44000/45333/ 46666/48000/49333/50666/52000/53333/54666/ 56000 bps Fax 2400/4800/7200/9600/12000/14400 bps Error correcting MNP class 4 and ITU-T V.42 Data compression MNP class 5 and ITU-T V.
Appendix B Display Controller and Modes Display controller The display controller interprets software commands into hardware commands that turn particular pels on or off. The controller is an advanced Video Graphics Array (VGA) that provides Super VGA (SVGA) and Extended Graphics Array (XGA) support for the internal LCD and external monitors. A high-resolution external monitor connected to the computer can display up to 2048 horizontal and 1536 vertical pixels at up to 16M colors.
Display Controller and Modes Video Modes The computer supports video modes defined in the table below. If your application offers a selection of mode numbers that do not match the numbers on the table, select a mode based on, resolution, number of colors and refresh rates.
Appendix C V.90/V.92 The TOSHIBA internal modem uses V.90 technology. The modem is capable of downstream speeds of 56Kbps (kilobits per second) when connected to an Internet service provider that supports V.90/V.92. As with any modem, the actual throughput (speed of data transfer) depends on analog telephone line conditions, which can vary considerably. Therefore, many users will experience throughput in the range of 32-44Kbps under normal telephone line conditions. Upstream data flows at the V.34 rate. V.
V.90/V.92 Result codes for a V.90 connection No.
V.90/V.92 AT Commands -V90=* V.90 Dial Line Rate -V90 sets the maximum V.90 downstream that the modem attempts to connect. User’s Manual -V90=0 V.90 disabled -V90=1 V.
Appendix D Wireless LAN This appendix is intended to help you get your Wireless LAN network up and running, with a minimum of parameters. Card specifications User’s Manual From Factor ■ Mini Card Compatibility ■ IEEE 802.11 Standard for Wireless LANs ■ Wi-Fi (Wireless Fidelity) certified by the Wi-Fi Alliance. The ‘Wi-Fi CERTIFIED’ logo is a certification mark of the Wi-Fi Alliance.
Wireless LAN Radio characteristics Radio characteristics of Wireless LAN cards may vary according to: ■ Country/region where the product was purchased ■ Type of product Wireless communication is often subject to local radio regulations. Although Wireless LAN wireless networking products have been designed for operation in the license-free 2.4 GHz and 5 GHz band, local radio regulations may impose a number of limitations to the use of wireless communication equipment.
Wireless LAN Wireless IEEE 802.11 Channels Sets (Revision B and G) Frequency Range Channel ID 2400-2483.5 MHz 1 2412 2 2417 3 2422 4 2427 5 2432 6 2437 7 2442 8 2447 9 2452 10 2457*1 11 2462 12 2467*2 13 2472*2 When installing Wireless LAN cards, the channel configuration is managed as follows: ■ For wireless clients that operate in a Wireless LAN infrastructure, the Wireless LAN card will automatically start operation at the channel identified by the Wireless LAN Access Point.
Wireless LAN Wireless IEEE 802.11 Channels Sets (Revision A) Frequency Range Channel ID 5150-5850 MHz 36 5180 40 5200 44 5220 48 5240 52 5260 56 5280 60 5300 Note 64 5320 100 5500*3 104 5520*3 108 5540*3 112 5560*3 116 5580*3 120 5600*3 124 5620*3 128 5640*3 132 5660*3 136 5680*3 140 5700*3 149 5745*3 US only*4 153 5765*3 US only*4 157 5785*3 US only*4 161 5805*3 US only*4 *1 Factory-set default channels.
Appendix E AC Power Cord and Connectors The power cord’s AC input plug must be compatible with the various international AC power outlets and the cord must meet the standards for the country/region in which it is used. All cords must meet the following specifications: Length: Minimum 1.7 meters Wire size: Minimum 0.75 mm2 Current rating: Minimum 2.5 amperes Voltage rating: 125 or 250 VAC (depending on country/region’s power standards) Certification agencies U.S.
AC Power Cord and Connectors In Europe, two conductors power cord must be VDE type, H05VVH2-F or H03VVH2-F and for three conductors power cord must be VDE type, H05VV-F. For the United States and Canada, two pin plug configuration must be a 2-15P (250V) or 1-15P (125V) and three pin plug configuration must be 6-15P (250V) or 5-15P (125V) as designated in the U.S. National Electrical code handbook and the Canadian Electrical Code Part II. The following illustrations show the plug shapes for the U.S.A.
Appendix F If your computer is stolen Always take care of your computer and try to prevent it from being stolen. You are the owner of a valuable technical device, which may be highly attractive to thieves, so please do not leave it unattended in a public place. To further help protect against theft, security cables can be bought for use with your notebook when it is being used at home or in the office. Make a note of your computer’s machine type, model number, and serial number, and put it in a safe place.
If your computer is stolen To register the theft online, please follow these procedures: ■ Visit www.toshiba-europe.com on the Internet. In the product area, choose Computer Systems. ■ In the Computer Systems page, open the Support & Downloads menu and choose the Stolen Units Database option. Your entries are used to track your computer at our service points. TOSHIBA Theft Registration Send to: Fax number: TOSHIBA Europe GmbH Technical Service and Support Leibnizstr.
Glossary The terms in this glossary cover the topics discussed in this manual. Alternate naming is included for reference.
Glossary HDD: hard disk drive IDE: integrated drive electronics I/O: input/output IrDA: Infrared Data Association IRQ: interrupt request KB: kilobyte LCD: liquid crystal display LED: light emitting diode LSI: large scale integration MDA: monochrome display adapter MPEG: moving picture coding experts group MS-DOS: Microsoft Disk Operating System OCR: optical character recognition (reader) PCB: printed circuit board PCI: peripheral component interconnect PCMCIA: Personal Computer Memory Card International As
Glossary A adapter: A device that provides an interface between two dissimilar electronic devices. For example, the AC adapter modifies the power from a wall outlet for use by the computer. This term also refers to the add-in circuit cards that control external devices, such as video monitors and magnetic tape devices. allocate: To assign a space or function for a specific task.
Glossary BIOS: Basic Input Output System. The firmware that controls data flow within the computer. See also firmware. bit: Derived from ìbinary digit,î the basic unit of information used by the computer. It is either zero or one. Eight bits is one byte. See also byte. Bluetooth: A short-range radio technology designed to simplify wireless communication among computers, communication devices and the Internet. board: A circuit board.
Glossary CGA: Color/graphics adapter. A video display protocol defined by the IBM Color/Graphics Monitor Adapter and its associated circuitry. This protocol supports two-color 640 × 200 and four-color 320 × 200 graphics, and 16-color 640 × 200 and 320 × 200 text modes. character: Any letter, number, punctuation mark, or symbol used by the computer. Also synonymous with byte. chassis: The frame containing the computer.
Glossary CPS: Characters per second. Typically used to indicate the transmission speed of a printer. CPU: Central processing unit. The portion of the computer that interprets and executes instructions. CRT: Cathode Ray Tube. A vacuum tube in which beams projected on a fluorescent screen-producing luminous spots. An example is the television set. cursor: A small, blinking rectangle or line that indicates the current position on the display screen.
Glossary driver: A software program, generally part of the operating system, that controls a specific piece of hardware (frequently a peripheral device such as a printer or mouse). E echo: To send back a reflection of the transmitted data to the sending device. You can display the information on the screen, or output it to the printer, or both.
Glossary G gigabyte (GB): A unit of data storage equal to 1024 megabytes. See also megabyte. GND: Ground. An RS-232C signal used in the exchange of data between a computer and serial device. graphics: The use of drawings, pictures, or other images, such as charts or graphs, to present information. H hard disk drive (HDD): An electromechanical device that reads and writes a hard disk. See also hard disk. hard disk: A non-removable disk usually referred to as drive C. Also called fixed disk.
Glossary input: The data or instructions you provide to a computer, communication device or other peripheral device from the keyboard or external or internal storage devices. The data sent (or output) by the sending computer is input for the receiving computer. instruction: Statements or commands that specify how to perform a particular task. interface: 1) Hardware and/or software components of a system used specifically to connect one system or device to another.
Glossary M main board: See motherboard. MDA: Monochrome Display Adapter. A video display protocol defined by the IBM Monochrome Display Adapter and its associated circuitry for direct drive TTL displays that supports a monochrome 720 × 350 text mode. megabyte (MB): A unit of data storage equal to 1024 kilobytes. See also kilobyte. megahertz: A unit of wave frequency that equals 1 million cycles per second. See also hertz. menu: A software interface that displays a list of options on the screen.
Glossary O OCR wand: A device that reads, using an optical device, hand written or machine printed symbols into a computer. See also OCR. OCR: Optical Character Recognition (reader). A technique or device that uses laser or visible light to identify characters and input them into a storage device. on-line state: A functional state of a peripheral device when it is ready to receive or transmit data. operating system: A group of programs that controls the basic operation of a computer.
Glossary port: The electrical connection through which the computer sends and receives data to and from devices or other computers. printed circuit board (PCB): A hardware component of a processor to which integrated circuits and other components are attached. The board itself is typically flat and rectangular, and constructed of fiberglass, to form the attachment surface. program: A set of instructions a computer can execute that enables it to achieve a desired result. See also application.
Glossary serial interface: Refers to a type of information exchange that transmits information sequentially, one bit at a time. Contrast: Parallel interface. serial port: A communications port to which you can connect devices, such as a modem, mouse, or serial printer. serial: The handling of data bits one after the other. SIO: Serial Input/Output. The electronic methodology used in serial data transmission.
Glossary V VGA: Video graphics array is an industry standard video adapter that lets you run any popular software. volatile memory: Random access memory (RAM) that stores information as long as the computer is connected to a power source. W Warm dock/undock: Connecting or disconnecting a device to or from the computer while the computer is suspended. warm start: Restarting or resetting a computer without turning it off. window: A portion of the screen that can display its own application or document.
Index A D AC adaptor, 1-6, 2-5 DC IN 15V port, 2-5 additional, 1-14, 8-10 connecting, 3-2 ASCII characters, 5-7 Auto power on, See Power DC IN indicator, 2-9, 6-3 Disk indicator, 2-9 Display, 1-5, 2-7 automatic power off, 1-9 opening, 3-2 See also Video modes and Monitor external selection, See Hot keys documentation list, 1-1 DVD-ROM drive, 1-4 using, 4-8 B Battery charger, 8-10 Battery pack, 6-4 additional, 8-10 location, 2-6 replacing, 6-10 Battery, See also Battery pack charging, 6-7 extending life,
Index Fn + Esc (Sound mute), 5-3 Fn + F1 (lock computer mode), 5-3 Fn + F2 (power save mode), 5-3 Fn + F3 (sleep), 5-3 Fn + F4 (hibernation), 5-3 Fn + F5 (display selection), 5-4 Fn + F6 (display brightness), 5-4 Fn + F7 (display brightness), 5-4 Fn + F8 (wireless setting), 5-4 Fn + F9 (Pad mode), 5-4 Fn + F10 (arrow mode), 5-2 Fn + F11 (numeric mode), 5-2 Fn + F12 (ScrLock), 5-2 Fn Sticky key, 5-5 Function keys, 5-2 H Hard disk drive, 1-4 automatic power off, 1-9 problems, 9-6 Hibernation, 1-11, 5-3 prob
Index Modem, 1-8, 4-18 connecting, 4-20 disconnecting, 4-20 jack location, 2-4 problems, 9-15 region selection, 4-18 using, 4-18 Monitor external problems, 9-13 Moving the computer, 4-24 N Numeric keypad, See Keypad overlay O Operating System, 1-9 Overlay, See Keypad overlay P Panel power on/off, See Power Password power on, 1-10 starting the computer with, 6-12 user, 7-2 PC card, 1-7 installing, 8-2 location of slots, 2-2 problems, 9-13 removing, 8-3 Ports DC IN 15V, 2-5 external monitor, 1-6, 2-2 head
Index Security lock, 1-9 attaching, 8-13 location, 2-4 Self Test, See Problems Serial port, See Ports, serial adaptor, 1-14, 2-14, 8-10 options, 1-14 Sleep, 1-11 Soft keys, 5-2 cursor control mode, 5-2 Enter, 5-3 numeric mode, 5-2 right Alt key, 5-3 right Ctrl key, 5-3 ScrLock, 5-2 Sound system, 1-7 headphone, 1-6, 2-2 microphone, 1-6, 2-1 problems, 9-14 speaker, 2-8 volume control, 2-1 W Wireless LAN, 1-8 using, 4-20 T TOSHIBA Power Saver, 1-11 TOSHIBA Theft Registration, F-2 TV, 8-11 U Utilities and A
