User’s Manual A110 Series GMR300613EN0 GMR300613EN0 Choose freedom. Choose freedom. computers.toshiba-europe.com computers.toshiba-europe.
A110 Series Copyright © 2006 by TOSHIBA Corporation. All rights reserved. Under copyright law, this manual cannot be reproduced in any form without the prior written permission of TOSHIBA. No patent liability is assumed, with respect to the use of the information contained herein. A110 Series Portable Personal Computer User's Manual First edition May 2006 Ownership and copyright of music, video computer programs, databases, etc. are protected by the copyright laws.
A110 Series TruSurround XT, WOW HD, Circle Surround Xtract, SRS and symbol are trademarks of SRS Labs, Inc. TruSurround XT, WOW HD, Circle Surround Xtract, TruBass, SRS 3D, Definition and FOCUS technologies are incorporated under license from SRS Labs, Inc. Other trademarks and registered trademarks not listed above may be used in this manual. Macrovision License of Notice This product incorporates copyright protection technology that is protected by methods and claims of certain U.S.
A110 Series ■ Before you connect the computer to a power source, ensure that the voltage rating of the AC adapter matches that of the available power source. 115V/60Hz in most of North and South America and some Far Eastern countries such as Taiwan. 100 V/50Hz in eastern Japan and 100 V/60Hz in western Japan. 230 V/50 Hz in most of Europe, the Middle East, and the Far East.
A110 Series When using telephone equipment in conjunction with your computer, basic safety precautions should always be followed to reduce the risk of fire, electric shock and injury to persons, including the following: ■ Do not use this product near water, for example, near a bathtub, washing bowl, kitchen sink or laundry tub, in a wet basement or near a swimming pool. ■ Avoid using a telephone (other than a cordless type) during an electrical storm.
A110 Series EU Declaration of Conformity CE compliance This product is labelled with the CE Mark in accordance with the related European Directives, notably Electromagnetic Compatibility Directive 89/ 336/EEC for the notebook and the electronic accessories including the supplied power adapter, the Radio Equipment and Telecommunications Terminal Equipment Directive 1999/5/EC in case of implemented telecommunication accessories and the Low Voltage Directive 73/23/EEC for the supplied power adapter.
A110 Series Optical Disc Drive Safety Instruction Be sure to check the international precautions at the end of this section. The optical drive that is used in this computer is equipped with a laser device. A classification label with the following sentence is affixed to the surface of the drive.
A110 Series International precautions ■ This drive employs a laser system. To ensure proper use of this product, please read this instruction manual carefully and retain for future reference. Should the unit ever require maintenance, contact an authorized service location. ■ Use of controls, adjustments or the performance of procedures other than those specified may result in hazardous radiation exposure. ■ To prevent direct exposure to the laser beam, do not try to open the enclosure.
A110 Series VORSICHT: Dieses Gerät enthält ein LaserSystem und ist als "LASERSCHUTZKLASSE 1 PRODUKT" klassifiziert. Für den richtigen Gebrauch dieses Modells lesen Sie bitte die Bedienungsanleitung sorgfältig durch und bewahren diese bitte als Referenz auf. Falls Probleme mit diesem Modell auftreten, benachrichtigen Sie bitte die nächste "autorisierte Service-Vertretung". Um einen direkten Kontakt mit dem Laserstrahl zu vermeiden darf das Gerät nicht geöffnet werden.
A110 Series Modem warning notice Conformity Statement The equipment has been approved to [Commission Decision "CTR21"] for pan- European single terminal connection to the Public Switched Telephone Network (PSTN). However, due to differences between the individual PSTNs provided in different countries/regions the approval does not, of itself, give an unconditional assurance of successful operation on every PSTN network termination point.
A110 Series General Precautions TOSHIBA computers are designed to optimize safety, minimize strain and withstand the rigours of portability. However, certain precautions should be observed to further reduce the risk of personal injury or damage to the computer. Be certain to read the general precautions below and to note the cautions included in the text of the manual. Stress injury Carefully read the Safety Instruction Manual.
A110 Series LCD Over a period of time, and depending on the usage of the computer, the brightness of the LCD screen will deteriorate. This is an intrinsic characteristic of LCD technology. Maximum brightness is only available when operating in AC power mode. The screen will dim when the computer is operated on battery power and you may not be able to increase the brightness of the screen.
A110 Series Network connection (Class A warning) If this product has networking capabilities and will be connected to a network, Class A radiation limits will be observed (in accordance with technical conventions). This means that if the product will be used in a domestic environment, other devices in the near surrounding area may suffer interference.
A110 Series Limitation of Liability For damage occurring due to an earthquake or thunder, fire beyond our responsibility, action by third party, other accident, intentional or accidental mistakes by a user, misuse or use under abnormal conditions, we do not take any responsibility. For incidental damage (loss of business profit, business interruption, etc.) occurring due to use or disability of the product, we do not take any responsibility.
A110 Series Warning Turn OFF the Wireless Communication switch of wireless products in a congested place, such as a crowded commuter train. Keep this product away from a cardiac pacemaker at least 22cm. Radio waves can potentially affect cardiac pacemaker operation, thereby causing respiratory troubles. Turn OFF the Wireless communication switch inside a medical facility or near medical electric equipment. Do not bring medical electric equipment close to the product.
Table of Contents Chapter 1 A110 Features Features. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-1 Special features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-8 Utilities. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-9 Options . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
A110 Series Chapter 4 Operating Basics Using the TouchPad . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-1 Using the internal modem . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-2 LAN . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-5 Wireless LAN . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-6 Using optical disc drives . . . . . . . . . . . . . . . . . . . .
A110 Series Chapter 8 Optional Devices PC Card . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-2 SD-IO/SD(miniSD with Adapter)/MMC/MS/MS Pro/xD Memory cards (optional) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-4 Memory expansion . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-7 Additional battery pack . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-10 Additional AC adapter . .
Preface Congratulations on your purchase of the A110 computer. This powerful notebook computer provides excellent expansion capability, including multimedia devices, and it is designed to provide years of reliable, highperformance computing. This manual tells how to set up and begin using your A110 computer. It also provides detailed information on configuring your computer, basic operations and care, using optional devices and troubleshooting.
A110 Series Chapter 5, The Keyboard, describes special keyboard functions including the keypad overlay and hotkeys. Chapter 6, Power and Power-Up Modes, gives details on the computer's power resources. Chapter 7, HW Setup, introduces you to the TOSHIBA Hardware Setup program. Chapter 8, Optional Devices, describes the optional hardware available.
A110 Series DISCCOPY A: B: When procedures require an action such as clicking an icon or entering text, the icon's name or the text you are to type in is represented in the type face you see to the left. Display ABC Names of windows or icons or text generated by the computer that appears on its display screen is presented in the type face you see to the left. Messages Messages are used in this manual to bring important information to your attention. Each type of message is identified as shown below.
A110 Series ■ TOSHIBA Assist ■ TOSHIBA Controls ■ TOSHIBA PC Diagnostic Tool ■ TOSHIBA Touch and Launch ■ TOSHIBA TouchPad On/Off Utility ■ TOSHIBA Zooming Utility ■ TOSHIBA SD Memory Card Format * ■ TOSHIBA Acoustic Silencer ■ TOSHIBA HW Setup ■ TOSHIBA Accessibility ■ TOSHIBA Virtual Sound ■ TOSHIBA Hotkey Utility ■ TOSHIBA Supervisor Password Utility ■ DVD-RAM Driver Software ■ InterVideo WinDVD Creator 2 Platinum ■ Online Manual ■ Product Recovery disc * The availability of this software is dependent o
Chapter 1 A110 Features This chapter identifies the computer's special features, options and accessories. Basic features are described in a separate pamphlet. Some of the features described in this manual may not function properly if you use an operating system that was not pre-installed by TOSHIBA.
A110 Features Chipset Mobile Intel® 945GM Express Chipset or ATI RADEON® XPRESS 200M ENE CB714 cardbus controller for the model with Multiple Digital Media card slot ENE CB1410 cardbus controller VIA6311S IEEE1394a controller Realtek ALC861 Audio codec Realtek RTL8100CL for 10/100Mbps LAN controller Memory The graphics system in your computer may use part of the main system memory for graphics performance and therefore reduce the amount of system memory available for other computing activities.
A110 Features BIOS 1MB Flash ROM for system BIOS Suspend to memory or hard disk drive Various Hotkey functions for system control Complete ACPI 1.0b functionality Power Battery Pack 4-cell Lithium Ion smart battery pack with 14.4V*2000mAh* 6-cell Lithium Ion smart battery pack with 10.8V*4000mAh 8-cell Lithium Ion smart battery pack with 14.4V*4300mAh Approximately 12 hours or longer charging time to 100% battery capacity with system switched on.
A110 Features TouchPad A TouchPad and control buttons in the palm rest enable control of the on-screen pointer. Display 15.4" TFT LCD screen with one of the following resolutions: ■ WXGA, 1280 horizontal × 800 vertical pixels ■ WXGA CSV, 1280 horizontal × 800 vertical pixels Disclaimer (LCD) For more information on the Disclaimer regarding LCD, please refer to the Chapter 10, Disclaimers.
A110 Features Disclaimer (HDD Drive Capacity) For more information on the Disclaimer regarding HDD Drive Capacity, please refer to the Chapter 10, Disclaimers. CD-RW/DVD-ROM drive User’s Manual Some models are equipped with a full-size CD-RW/DVD-ROM module that lets you record data to rewritable CD/CD-RWs as well as run either 12cm (4.72") or 8cm (3.15") CD/DVDs without using an adapter. It reads DVD-ROMs at maximum 8x speed and CD-ROMs at maximum 24x speed.
A110 Features DVD Super Multi drive Some models are equipped with a full-size DVD supporting R Double Super Multi drive supporting ±R Double Layer module with dual layer support that lets you Layer record data to rewritable CD/DVDs as well as run either 12cm (4.72") or 8cm (3.15") CD/DVDs without using an adapter. It reads DVD-ROMs at maximum 8x speed and CD-ROMs at maximum 24x speed.
A110 Features Universal Serial Bus The computer has three Universal Serial Bus (USB) ports that comply with the USB 2.0 standard, which enables data transfer speeds more than 40 times faster than USB 1.1 (which this computer also supports). i.LINK (IEEE1394a) This port enables high-speed data transfer directly from external devices such as digital video cameras. TV Out The 4-pin S-Video port is compatible with PAL or NTSC TV standard, supporting Macrovision 7.02 copy protection.
A110 Features Security Lock Slot Receives an optional security lock in order to anchor the computer to a desk or other large, heavy object. Special features The following features are either unique to TOSHIBA computers or are advanced features, which make the computer more convenient to use. User’s Manual Hotkeys Key combinations that let you quickly modify the system configuration directly from the keyboard without running a system configuration program.
A110 Features Panel Power Off/On This feature turns power to the computer off when the display panel is closed and turns it back on when the panel is opened. You can specify the setting in the TOSHIBA Power Saver utility. Low Battery Automatic Hibernation When battery power is exhausted to the point that computer operation cannot be continued, the system automatically enters Hibernation Mode and shuts itself down. You can specify the setting in the TOSHIBA Power Saver utility.
A110 Features User’s Manual TOSHIBA Power Saver TOSHIBA Power Saver provides configuration option to conserve power when the computer is running on either battery or mains power.
A110 Features TOSHIBA ConfigFree ConfigFree is a suite of utilities to allow easy control of communication devices and network connections. ConfigFree also allows you to find communication problems and create profiles for easy switching between location and communication networks. To start ConfigFree, click the Start Button, point to All Programs, point to TOSHIBA, point to Networking and click ConfigFree.
A110 Features TOSHIBA Hardware Setup This program lets you customize your hardware settings according to the way you work with your computer and the peripherals you use. To access this utility, click Start, click Control Panel, click Printers and Other Hardware and select the TOSHIBA HW Setup icon. TOSHIBA Accessibility This utility lets you make the Fn key sticky, that is, you can press it once, release it, and then press an "F number" key. The Fn key remains active until another key is pressed.
A110 Features Options You can add a number of options to make your computer even more powerful and convenient to use. The following options are available: Memory Modules Two memory module can be installed in this computer. Use only PC4200 and PC5300* compatible DDRII memory modules. See your TOSHIBA dealer for details * The availability of DDRII is dependent on the model you purchased. Battery Pack An additional battery pack can be purchased from your TOSHIBA dealer.
Chapter 2 The Grand Tour This chapter identifies the various components of your computer. Become familiar with each component before you operate the computer. Certain types of notebook chassis are designed to accommodate all possible configurations for an entire product series. Your selected model may not have all the features and specifications corresponding to all of the icons or switches shown on the notebook chassis, unless you have selected all those features.
The Grand Tour DC IN LED The DC IN LED indicates the computer is connected to the AC adapter and it is plugged into an AC power source. Power LED In normal operating mode, the Power LED is green or blue (depending on the model you purchased). If the system is in Standby Mode the LED will flash amber, while the LED will be off when the computer is turned off or is in Hibernation Mode. Battery LED The Battery LED indicates the battery's current charge/discharge status.
The Grand Tour Right side The following figure shows the computer's right side. 2 1 1. Optical Disc Drive 2. Optical Disc Drive LED The right side of the computer User’s Manual Optical Disc Drive The computer is configured with a full-size optical disc drive module that lets you run either 12 cm (4.72") or 8 cm (3.15") discs without using an adapter.
The Grand Tour Left side The following figure shows the computer's left side. 1 1. 2. 3. RGB Monitor Port Fan Vents TV Out (S-Video) Port 2 3 4 4. 5. 6. 5 6 i.LINK (IEEE1394a) Port Universal Serial Bus (USB) Port PC Card Slot The left side of the computer RGB Monitor Port This 15-pin port lets you connect an external video display to the computer. Fan Vents The fan vents help prevent the CPU from overheating. To prevent possible over heating of the CPU, never block the fan vent.
The Grand Tour Back side The following figure shows the computer back panel. 1 1. 2. 3. 3 2 Modem Jack Security Lock LAN Jack 4. 5. 4 5 Universal Serial Bus (USB) Ports DC IN 19V Jack The back side of the computer User’s Manual Modem Jack In regions where an internal modem is installed as standard equipment, this jack lets you use a modular cable to connect the modem directly to a telephone line.
The Grand Tour Underside The following figure shows the underside of the computer. Make sure the display is closed before turning over your computer. 1 5 2 4 3 1. 2. 3. Expansion Memory Socket Fan Vent Battery Pack Latch 4. 5. Battery Pack Battery Pack Lock The bottom of the computer Expansion Memory Socket Use this socket to install a memory module to increase your computer's memory. Refer to the Memory expansion section in Chapter 8, Optional Devices.
The Grand Tour Front with the display open The following figure shows the front of the computer with the display open. To open the display, push the latch on the front of the display and lift it up. Position the display at a comfortable viewing angle. 1 5 6 7 8 9 10 11 2 3 4 1. 2. 3. 4. 5. 6. Display Screen TouchPad TouchPad Control Buttons Left and Right Speakers Power Button Internet Button* 7. 8. 9. 10. 11.
The Grand Tour TouchPad The TouchPad pointing device is located in the centre of the palm rest and is used to control the on-screen pointer. Refer to the Using the internal modem section in Chapter 4, Operating Basics. TouchPad Control Buttons Control buttons below the TouchPad let you select menu items or manipulate text and graphics designated by the on-screen pointer. Left and Right Speakers The computer provides two speakers for stereo sound reproduction.
The Grand Tour If Random or Shuffle is selected in Windows® Media Player, selecting Next or Previous advances to a random selection. Keyboard Indicators Arrow Mode Numeric Mode Caps Lock Arrow Mode When the Arrow mode icon lights green, you can use the keypad overlay (light gray labelled keys) as cursor keys. Refer to the Keypad overlay section in Chapter 5, The Keyboard.
The Grand Tour Code Region 5 Russia, Indian Subcontinent, Africa, North Korea, Mongolia 6 China Writable discs This section describes the types of writable discs. Check the specifications for your drive to for the type of discs it can write. Use TOSHIBA Disc Creator to write compact discs. Refer to Chapter 4, Operating Basics. CDs ■ CD-R discs can be written only once. The recorded data cannot be erased or changed. ■ CD-RW discs can be recorded more than once.
The Grand Tour The read speed is slower at the centre of a disc and faster at the other edge. DVD read 8 speed (maximum) DVD-R write 8 speed (maximum) DVD-RW write 4 speed (maximum) DVD+R write 8 speed (maximum) DVD+RW write 4 speed (maximum) DVD-RAM write 5 speed (maximum) CD read 24 speed (maximum) CD-R write 24 speed (maximum) CD-RW write 10 speed (maximum, ultra-speed media) DVD+R (DL) write 2.
Chapter 3 Getting Started This chapter provides basic information to get you started using your computer. It covers the following topics: ■ Setting up your work space - for your health and safety Be sure also to read Instruction Manual for Safety & Comfort. This guide, which is included with the computer, explains product liability.
Getting Started ■ Work habits General conditions In general, if you are comfortable, so is your computer, but read the following to make sure your work site provides a proper environment. ■ Make sure there is adequate space around the computer for proper ventilation. ■ Make sure the AC power cord connects to an outlet that is close to the computer and easily accessible.
Getting Started Seating and posture The height of your chair in relation to the computer and keyboard as well as the support it gives your body are primary factors in reducing work strain. Below eye level 90°angles Foot rest Posture and positioning of the computer ■ Place your chair so that the keyboard is at or slightly below the level of your elbow. You should be able to type comfortably with your shoulders relaxed. ■ Your knees should be slightly higher than your hips.
Getting Started Work habits A key to avoiding discomfort or injury from repetitive strain is to vary your activities. If possible, schedule a variety of tasks into your work day. If you must spend long periods at the computer, finding ways to break up the routine can reduce stress and improve your efficiency. ■ Sit in a relaxed posture. Good positioning of your chair and equipment as described earlier can reduce tension in your shoulders or neck and ease back strain. ■ Vary your posture frequently.
Getting Started 1. Connect the power cord to the AC adapter. Connecting the power cord to the AC adapter 2. Connect the DC output plug on the AC adapter to the DC IN input port on the back of the computer. Connecting the adapter to the computer 3. Plug the power cord into a live wall outlet. The Battery and DC IN indicators on the front of the computer should glow. To disconnect AC adaptor, you can follow the reversed procedure of Connecting AC adaptor.
Getting Started 2. Lift the panel up and adjust it to the best viewing angle for you. Use reasonable care when opening and closing the display panel. Opening it vigorously or slamming it shut could damage the computer. Turning on the power This section describes how to turn on the power. After you turn on the power for the first time, do not turn it off until you have set up the operating system. Refer to the section Starting up for the first time in this chapter. 1.
Getting Started Turning off the power The power can be turned off in one of three modes, either Shutdown Mode (also known as Boot Mode), Hibernation Mode or Standby Mode. Shut Down mode (Boot mode) When you turn off the power in Shut Down mode, no data is saved and the computer will boot to the operating system's main screen. 1. If you have entered data, save it to the hard disc, to writable optical media or to a disc. 2.
Getting Started ■ You can return to your previous working environment immediately when you turn on the computer. ■ Saves power by shutting down the system when the computer receives no input or hardware access for the duration set by the System hibernate feature. ■ You can use the panel power off feature. Starting Hibernation You can also enable Hibernation by pressing Fn + F4. See Chapter 5, The Keyboard, for details. To enter Hibernation mode, follow the steps below. 1. Click Start. 2. Select Shut Down.
Getting Started Standby mode In standby mode the power remains on, but the CPU and all other devices are in sleep mode. ■ If the computer is not used or accessed in any way, including areas such as the receipt of an e-mail, for approximately 15 or 30 minutes when the AC adapter is connected, it will automatically enter Standby Mode. This function is the default setting within the TOSHIBA Power Saver utility. ■ To restore operation, press the power button.
Getting Started Enabling Standby You can also enable Standby by pressing Fn + F3. See Chapter 5, The Keyboard, for details. You can enter standby mode in one of three ways: 1. Click Start, then Shut Down and then Stand by. 2. Close the display panel. This feature must be enabled. Refer to the Setup Action tab in TOSHIBA Power Saver Utility described in the Control Panel. 3. Press the power button. This feature must be enabled.
Getting Started Restoring the pre-installed software from the Product Recovery disc If preinstalled files are damaged, use the Product Recovery disc to restore them. To restore the operating system and all preinstalled software, follow the steps below. When you reinstall the Windows® operating system, the hard disc will be reformatted and all data will be lost. 1. Load the Product Recovery disc in the drive and turn off the computer's power. 2.
Chapter 4 Operating Basics This chapter gives information on basic operations including using the TouchPad, optical disc drives, the internal modem, LAN and wireless LAN. It also provides tips on caring for your computer and on heat dispersal. Using the TouchPad To use the TouchPad, simply move your finger tip across it in the direction you want the on-screen pointer to go. 2 1 1. TouchPad control buttons 2.
Operating Basics Do not press on the TouchPad too hard or press a sharp object such as a ball point pen against it. The TouchPad could be damaged. The TouchPad has similar functions to a two-button mouse with a scroll wheel. For some functions, you can tap it instead of pressing a button. You can customize pointing device actions in Mouse Properties. Open the Control Panel, select the Mouse icon and press Enter to open the Mouse Properties window.
Operating Basics Region selection Telecommunication regulations vary from one country/region to another, so you will need to make sure the internal modem's settings are correct for the country/region in which it will be used. 1. Open the Modem Region Select application. It is located on the Programs menu at TOSHIBA Networking. Do not use the Country/Region Select function in the Modem setup utility in the Control Panel if the function is available.
Operating Basics Settings You can enable or disable the following settings: AutoRun Mode Region Select Utility starts automatically when you start up the operating system. Open the Dialling Properties dialogue box after selecting region. The dialling properties dialogue box will be displayed automatically after you select the region. Location list for region selection. A submenu appears displaying location information for telephony.
Operating Basics Connecting the internal modem Do not pull on the cable or move the computer while the cable is connected. If you use a storage device such as an optical media drive or hard disc drive connected to a 16-bit PC Card, you may find that the modem speed is slow or the communication session might be interrupted. If you find that the modem speed is low or communication is interrupted when you are using the modem, please set the CPU speed to Maximum within the TOSHIBA Power Saver utility.
Operating Basics Connecting the LAN cable The computer must be configured properly before connecting to a LAN. Logging onto a LAN using the computer's default settings could cause a malfunction in LAN operation. Check with your LAN administrator regarding set-up procedures. If you are using Ethernet LAN (10 megabits per second, 10BASE-T), you can connect using either a CAT5 or a CAT3 cable. If you are using Fast Ethernet LAN (100 megabits per second, 100BASE-TX), you can use a CAT5 cable.
Operating Basics Wake-up on LAN does not function on a Wireless LAN. ■ ■ ■ ■ Frequency Channel Selection (5GHz and 2.4 GHz) Roaming over multiple channels Card Power Management Wi-Fi Protected Access (WPA) data encryption Security 1. TOSHIBA strongly recommends that you enable the WPA encryption function otherwise your computer could be left open to illicit access via the wireless LAN connection which may result in an intrusion that can lead to the theft or loss of stored data among other things.
Operating Basics If you have a CD-RW/DVD-ROM drive, refer also to the Writing CDs on a CD-RW/DVD-ROM drive section for precautions on writing to CDs. If you have a DVD Super Multi drive supporting ±R Double Layer, refer also to the Writing CDs/DVDs on a DVD Super Multi drive supporting ±R Double Layer section for precautions on writing to CDs. Loading optical disc media To load a disc, follow the steps below. 1. Turn on the power. 2. a. Press the eject button to open the drawer slightly.
Operating Basics 3. Grasp the drawer gently and pull until it is fully open. Pulling the drawer open 4. Lay the disc, label side up, in the drawer. Inserting a disc Be careful not to touch the lens or the area around it. Doing so could cause the drive to malfunction. 5. Press gently at the centre of the disc until you feel it click into place. The disc should lie below the top of the spindle, flush with its base. 6. Push the centre of the drawer to close it. Press gently until it locks in place.
Operating Basics Closing the drive drawer Removing optical disc media To remove the disc, follow the steps below. Do not press the eject button while the computer is accessing the disc drive. Wait for the optical disc indicator to go out before you open the drawer. Also, if the disc is spinning when you open it, wait for it to stop before you remove it. 1. To pop the drawer partially open, press the eject button. Gently pull the drawer out until it is fully opened.
Operating Basics Buttons The Internet button and the CD/DVD button can be assigned functions and applications in the TOSHIBA Controls Properties.
Operating Basics If Random or Shuffle is selected in Windows® Media Player, selecting Next or Previous advances to a random selection. Writing CDs on a CD-RW/DVD-ROM drive You can use the CD-RW/DVD-ROM drive to write data to CD-R/RW discs. The following applications for writing are preinstalled: TOSHIBA Disc Creator/TOSHIBA Direct Disc Writer. Important message Before you write or rewrite to CD-R/RW media, read and follow all setup and operating instructions in this section.
Operating Basics Before writing or rewriting Please observe the following points when you write or rewrite the data. ■ We recommend the following manufacturers of CD-R and CD-RW media. Media quality can affect write or rewrite success rates. CD-R: TAIYOYUDEN CO., LTD. MITSUBISHI KAGAKU MEDIA CO. LTD RICOH Co., Ltd. Hitachi Maxell Ltd. CD-RW: MITSUBISHI KAGAKU MEDIA CO. LTD RICOH Co., Ltd. TOSHIBA has confirmed the operation of CD-R and CD-RW media of the manufacturers above.
Operating Basics ■ Install, remove or connect external devices such as PC Cards, USB devices, an external display, i.LINK devices or optical digital devices. ■ Open the optical disc drive. ■ If the media is poor in quality, dirty or damaged, writing or rewriting errors may occur. ■ Set the computer on a level surface and avoid places subject to vibration, such as airplanes, trains, or cars. Do not use an unstable surface, such as a stand.
Operating Basics Before writing or rewriting Please observe the following points when you write or rewrite data. ■ Based on TOSHIBA's limited compatibility testing, we suggest the following manufacturers of CD-R/RW and DVD-R/+R/-RW/+RW/-RAM media. However, in no event does TOSHIBA guarantee the operation, quality or performance of any disc. Disc quality can affect write or rewrite success rates. CD-R: TAIYOYUDEN CO., LTD. MITSUBISHI KAGAKU MEDIA CO. LTD RICOH Co., Ltd. Hitachi Maxell Ltd.
Operating Basics ■ There are two types of DVD-R: authoring and general use discs. Do not use authoring discs. Only general use discs can be written to by a computer drive. ■ We can support only format 1 of DVD-R DL. Therefore you can not do the additional writing. If your data is under DVD-R (SL) capacity, we suggest to use DVD-R (SL) media. ■ You can use DVD-RAM discs that can be removed from a cartridge and DVD-RAM discs designed without a cartridge. You cannot use a disc with a 2.
Operating Basics ■ Write from the computer's hard disc drive to the CD. Do not try to write from shared devices such as a LAN server or any other network device. ■ Writing with software other than TOSHIBA Disc Creator or InterVideo WinDVD Creator 2 Platinum has not been confirmed. Therefore, operation with other software cannot be guaranteed. When writing or rewriting Please observe/consider the following when you write or rewrite to a CD-R/ RW, DVD-R/-RW/-RAM or DVD+R/+RW disc.
Operating Basics ■ You cannot back up DVD-ROM, DVD-Video or DVD-R/-RW or DVD+R/ +RW to CD-R/RW using TOSHIBA Disc Creator ■ TOSHIBA Disc Creator cannot record in packet format. ■ You might not be able to use the "Disc Backup" function of TOSHIBA Disc Creator to backup a DVD-R/-RW or DVD+R/+RW disc that was made with other software on a different DVD-R/-RW or DVD+R/+RW recorder.
Operating Basics ■ TOSHIBA Direct Disc Writer does not support formatting a DVD-RAM disc and writing to it. They are performed by DVD-RAM Driver Software. If TOSHIBA Direct Disc Writer Format menu may appear when inserting a DVD-RAM disc into the drive and right-clicking the drive icon in Windows Explorer, please use "DVDForm" to format this disc.
Operating Basics How to make a DVD-Video Simplified steps for making a DVD-Video from video data captured from a DV-Camcorder: 1. Click Start All Programs InterVideo WinDVD Creator 2 InterVideo WinDVD Creator to launch WinDVD Creator. 2. Click the Capture button then capture the video data from the DV-Camcorder via the IEEE1394a connection. 3. Click the Edit button then drag the video clips from Video Library tab to the edit track. 4. Click the Make Movie button in the top bar. 5.
Operating Basics ■ While recording video to DVD or tape, please close all other programs. ■ Do not run software like a screen saver because it can put a heavy load on the CPU. ■ Do not run communication applications like a modem or a LAN. 2. Before recording the video to DVD ■ When you record to DVD media, please use only discs recommended by the drive manufacturer. ■ Do not set the working drive to be a slow device like a USB 1.1 hard disc drive or it will fail to write the DVD.
Operating Basics ■ If you use an over-used rewritable disc, the full formatting might be locked. Please use a brand new disc. Media Care This section provides tips on protecting data stored on your discs. Handle your media with care. The following simple precautions will increase the lifetime of your media and protect the data stored on it: 1. Store your discs in the container they came in to protect them and keep them clean. 2. Do not bend the disc. 3.
Operating Basics TV-Out Use the TV-Out port to connect to a television. Be sure to use a 4 pin type S-video cable. For more details, see Appendix B, Display Modes. TV Out Port Setting up more than one display You can set up your computer to utilize more than one display, effectively spreading a single desktop screen across two monitors. The Display Properties window allows you to adjust more precisely the relative positioning of the two displays when they are configured as an extended desktop.
Operating Basics Cleaning the computer To help ensure long, trouble-free operation, keep the computer free of dust and use care with liquids around the computer. ■ Be careful not to spill liquids into the computer. If the computer does get wet, turn the power off immediately and let the computer dry completely before you turn it on again. ■ Clean the computer using a slightly damp (with water) cloth. You can use glass cleaner on the display.
Chapter 5 The Keyboard The computer's keyboard layouts are compatible with a 101/102-key enhanced keyboard. By pressing some keys in combination, all the 101/ 102-key keyboard functions can be executed on the computer. The number of keys on your keyboard depends on which country/region's keyboard layout your computer is configured with. Keyboards for numerous languages are available. There are five types of keys: typewriter keys, keypad overlay, function keys, soft keys and cursor control keys.
The Keyboard F1 ... F12 function keys The function keys, not to be confused with Fn, are the 12 keys at the top of your keyboard. These keys are dark gray, but function differently from the other dark gray keys. F1 through F12 are called function keys because they execute programmed functions when pressed. Used in combination with the Fn key, keys marked with icons execute specific functions on the computer. See the section, Soft keys: Fn key combinations, in this chapter.
The Keyboard Press Fn + Ctrl to simulate the enhanced keyboard's right Ctrl key. Hotkeys Fn + ESC Volume Mute: Turns the volume on and off. Fn + F1 Instant Security: Enters screen saver mode and blanks the screen. To restore your desktop, press any key or use the TouchPad. Fn + F2 Power Save Modes: Displays the power save modes and lets you change the power settings Fn + F3 Standby: This hot key switches the system to Standby mode.
The Keyboard Fn + 1 Zoom Out: To reduce the icon size on the desktop or the application window, press the 1 key while holding down the Fn key. Fn + 2 Zoom In: To enlarge the icon size on the desktop or the application window, press the 2 key while holding down the Fn key. Before using Fn + 1 and Fn + 2, you must install the TOSHIBA Zooming Utility.
The Keyboard Numeric mode To turn on the Numeric mode, press Fn + F11 (Numeric mode indicator lights). Now try numeric data entry using the keys below. Press Fn + F11 again to turn off the overlay. The numeric keypad overlay (U.S.) Temporarily using normal keyboard (overlay on) While using the overlay, you can temporarily access the normal keyboard without turning off the overlay: 1. Hold down Fn and press any other key. All keys will operate as if the overlay were off. 2.
The Keyboard Temporarily changing modes If the computer is in Numeric mode, you can switch temporarily to Arrow mode by pressing a shift key. If the computer is in Arrow mode, you can switch temporarily to Numeric mode by pressing a shift key. Generating ASCII characters Not all ASCII characters can be generated using normal keyboard operation. But, you can generate these characters using their ASCII codes. With the overlay on: 1. Hold down Alt. 2. Using the overlay keys, type the ASCII code. 3.
Chapter 6 Power and Power-Up Modes The computer's power resources include the AC adapter and internal batteries. This chapter gives details on making the most effective use of these resources including charging and changing batteries, tips for saving battery power, and power up modes.
Power and Power-Up Modes Power on AC adapter not connected Power off (no operation) Battery capacity • Operates is above low • LED: Battery off battery trigger DC IN off point Battery capacity is below low battery trigger point • Operates • Alarm sounds (this function depends on how the computer is configured) • LED: Battery flashes amber DC IN off Battery capacity Computer goes into exhausted Hibernation or shuts down (depending on the TOSHIBA Power Saver setting) No battery installed • No operation
Power and Power-Up Modes DC IN indicator Check the DC IN indicator to determine the power status with the AC adapter connected: Blue/Green Indicates the AC adapter is connected and is correctly supplying power to the computer. No light Indicates the AC adapter is not connected. Power indicator Check the Power indicator to determine the power status with the AC adapter connected: Blue/Green Indicates power is being supplied and the computer is turned on.
Power and Power-Up Modes ■ The battery pack is a lithium ion battery, which can explode if not properly replaced, used, handled or disposed of. Dispose of the battery as required by local ordinances or regulations. Use only batteries recommended by TOSHIBA as replacements. ■ Do not remove the battery pack while the computer is in Standby Mode. In this mode data is stored in memory, so if the computer loses power, it will be lost.
Power and Power-Up Modes When this error appears, the following action is recommended. 1. Connect the AC adapter and let the battery charge for 24-hours. 2. Press F2 to enter BIOS setup menu. 3. Set correct time and date. If you still see the error message after performing the above actions, please contact your TOSHIBA service representative. Care and use of the battery pack The battery pack is a vital component of portable computing.
Power and Power-Up Modes 6. Use only the battery pack supplied with the computer or other device or an battery pack approved by the computer or device's manufacturer. Battery packs have different voltages and terminal polarities. Use of an improper battery could cause smoke, fire or rupture of the battery pack. 7. Never subject a battery pack to heat, such as storage near a heat source. Exposure to heat can cause the battery pack to ignite, explode or leak caustic liquid and cause death or serious injury.
Power and Power-Up Modes 5. Charge the battery pack only in an ambient temperature between 5 and 30 degrees Celsius. Otherwise, the electrolyte solution might leak, battery pack performance might deteriorate and the battery life might be shortened. 6. Be sure to monitor the remaining battery power. If the battery pack or real time clock battery discharge completely, Standby Mode will not function, and data in memory will be lost, and the computer might register an incorrect time and date.
Power and Power-Up Modes Time The following table shows the time required to fully charge a discharged battery. Charging time (hours) Battery type Power on Power off Battery pack about 12 or longer about 4 or longer RTC battery about 24 about 24 with AC or Battery pack The charging time when the computer is on is affected by ambient temperature, the temperature of the computer and how you use the computer.
Power and Power-Up Modes Leaving the AC adapter connected will shorten battery life. At least once a week, run the computer on battery power until the battery is fully discharged, then recharge the battery. Monitoring battery capacity Remaining battery power can be monitored by the TOSHIBA Power Saver. Refer to Utilities in Chapter 1, A110 Features. ■ Wait for a moment after turning on the computer before trying to monitor the remaining operating time.
Power and Power-Up Modes Retaining data with power off (standby mode) When you turn off your computer with fully charged batteries, the batteries retain data/charge for the following approximate time periods: Battery Approximately 1.5 days (Standby mode, 8-cell) Approximately 1 day (Standby mode, 6-cell) Approximately 0.
Power and Power-Up Modes 1 Removing the battery pack-1 7. Slide the battery pack latch to the left, then pull the battery out of the battery bay. 2 3 Removing the battery pack-2 Installing the battery pack To install a battery pack, follow the steps below. The battery pack is a lithium ion battery, which can explode if not properly replaced, used, handled or disposed of. Dispose of the battery as required by local ordinances or regulations. Use only batteries recommended by TOSHIBA as replacements. 1.
Power and Power-Up Modes 2 1 Installing the battery pack TOSHIBA Password Utility The TOSHIBA Supervisor Password Utility provides two levels of password security: User and Supervisor. Passwords set in TOSHIBA Supervisor Password Utility are different from the Windows® login password. User Password To start the utility, point to or click the following items: Launch TOSHIBA Assist SECURE User Password ■ Registered Click to register a password of up to 8 characters.
Power and Power-Up Modes Starting the computer by password If you registered a password, start the computer by entering the password manually. The password is necessary only if the computer was shut down in boot mode, not in Hibernation or Standby mode. To enter a password manually, follow these steps: 1. Turn on the power as described in Chapter 3, Getting Started. The following message will appear in the LCD: Enter Password [xxxxxxxx] 2. Enter the Password. 3. Press Enter.
Chapter 7 HW Setup This chapter explains how to use the TOSHIBA HW Setup utility to configure your computer. TOSHIBA HW Setup lets you configure settings for various hardware devices through a number of tabs titled General, Password, Display, Boot Priority, Keyboard, CPU, LAN, and USB. Some models are not equipped with the CPU tab. Accessing HW Setup To run HW Setup, click Start, click Control Panel, click Printers and Other Hardware and select TOSHIBA HW Setup.
HW Setup General This window displays the BIOS version and contains two buttons: Default Return all HW Setup values to the factory settings. About Display the HW Setup version. Setup This field displays BIOS Version and date. Password This tab allows you to set or reset the user password for power on. Display This tab lets you customize your computer's display settings for either the internal LCD screen or for an external monitor.
HW Setup Boot Priority Boot Priority Options This option sets the priority for booting the computer. Select the boot priority from the drop down list. You can override the settings and manually select a boot device by pressing one of the following keys while the computer is booting: U Selects the USB floppy disk drive. N Selects the Network. C Selects optical device. To select the boot drive you want, follow the steps below. 1. Boot-up your computer and press F12 to enter the boot menu. 2.
HW Setup LAN Wake-up on LAN This feature lets the computer's power be turned on when it receives a wake-up signal from the LAN. Enabled Enables Wake-up on LAN. Disabled Disables Wake-up on LAN (Default). The Wake-up on LAN function consumes power even when the system is off. Leave the AC adaptor connected while using this feature. Do not install or remove an optional memory module while Wake-up on LAN is enabled. Built-in LAN This feature enables or disables the Built-in LAN.
Chapter 8 Optional Devices Optional devices can expand the computer's capabilities and its versatility.
Optional Devices PC Card The computer is equipped with a PC Card expansion slot that can accommodate one 5 mm Type II card. Any PC Card that meets industry standards (manufactured by TOSHIBA or other vendor) can be installed. The slots support 16-bit PC Cards, including PC Card 16's multifunction card and CardBus PC Cards. CardBus supports the new standard of 32-bit PC cards. The bus provides superior performance for the greater demands of multimedia data transmission.
Optional Devices Removing a PC card 1. 2. 3. 4. 5. Click the Safely Remove Hardware icon on the Task Bar. Click the PC Card you want to remove. Press the eject button of the PC Card to extend it. Press the extended eject button to pop the card out slightly. Grasp the PC Card and remove it.
Optional Devices SD-IO/SD(miniSD with Adapter)/MMC/MS/MS Pro/ xD Memory cards (optional) The computer is equipped with a multiple digital media card slot that can accommodate SD-IO/SD(miniSD with Adapter)/MMC/MS/MS Pro/xD memory cards. These memory cards let you easily transfer data from devices, such as digital cameras and Personal Digital Assistants, which use flash-memory.
Optional Devices Installing a memory card To install a memory card: 1. Insert the memory card. 2. Press gently to ensure a firm connection. Inserting a memory card Be sure the memory card is oriented properly before you insert it. If Windows® fails to read the card, remove it then re-insert it. The multiple digital media card slot only accepts one type of card at a time. Do not attempt to install more than one card as you risk damaging either the cards themselves or the computer.
Optional Devices 4. Grasp the card and remove it. Removing a memory card ■ Make sure the memory card indicator is out before you remove the card or turn off the computer's power. If you remove the card or turn off the power while the computer is accessing the card you may lose data or damage the card. ■ Do not remove the card while the computer is in Standby or Hibernation mode. The computer could become unstable or data in the memory card could be lost.
Optional Devices Memory expansion You can install additional memory in the computer's memory module socket to increase the amount of RAM. This section describes how to install and remove a memory module. ■ Before you install or remove a memory module, turn off the computer with the Shut Down option in the Windows Start menu. If you install or remove a memory module while the computer is in Standby or Hibernation mode, data will be lost.
Optional Devices 5. Slide your fingernail or a thin object under the cover and lift it off. Removing the memory module socket cover 6. Fit the module's connectors into the computer's connectors at about a 45 degree angle and press the module carefully to ensure a firm connection. Do not touch the connectors on the memory module or on the computer. Debris on the connectors may cause memory access problems. 7. Push the module down so it lies flat.
Optional Devices Removing a memory module If you use the computer for a long time, the memory modules will become hot. In this case, let the memory modules cool to room temperature before you replace them. To remove the memory module, make sure the computer is in boot mode then: 1. Be sure the power is off and all cables are disconnected from the computer. Do not try to remove a memory module with the computer turned on. You can damage the computer and the module. 2.
Optional Devices Additional battery pack You can increase the portability of the computer with additional battery packs. If you're away from an AC power source and your battery runs low, you can replace it with a freshly charged battery. See Chapter 6, Power and Power-Up Modes. Additional AC adapter If you frequently carry the computer to different sites such as your home and office, having an AC adapter at each location reduces the weight and bulk of your load.
Optional Devices For the ATI Graphics Controller 1. Click Start Control Panel Display. 2. Click the Settings tab. 3. Click the Advanced button and choose Displays.
Optional Devices 4. Click the TV button to open the TV Properties dialog box. 5. Adjust the TV properties accordingly. 6. Adjusting the TV settings. For the Intel Graphics Controller 1. Click Start Control Panel Appearance and Themes. 2. Choose Display to open the Display Properties dialog box. 3. Click Setting tab.
Optional Devices 4. Click the Advanced button and choose Intel® Graphics Media Accelerator Driver. 5. Click the Graphic Properties button and choose TV.
Optional Devices 6. Adjusting the TV settings. i.LINK (IEEE1394a) i.LINK (IEEE1394a) is used for high-speed data transfer for a range of compatible devices such as: ■ Digital video cameras ■ Hard disk drives ■ MO drives ■ Optical disc drives i.LINK uses a four-pin connector, which does not carry electric current. External devices will need their own power supply. Precautions ■ Make a back-up of your data before transferring it to the computer.
Optional Devices Connecting 1. Make sure the connectors are properly aligned and plug the i.LINK (IEEE1394a) cable into the computer. 2. Plug the other end of the cable into the device. Note the following when you use i.LINK: ■ You may need to install drivers for your i.LINK devices. ■ Not all i.LINK devices have been tested. Therefore, compatibility with all i.LINK devices cannot be guaranteed. ■ Use S100, S200 or S400 cables no longer than three meters.
Chapter 9 Troubleshooting TOSHIBA designed the computer for durability. However, should problems occur, following the procedures in this chapter can help to determine the cause. All readers should become familiar with this chapter. Knowing what might go wrong can help prevent problems from occurring. Problem solving process Resolving problems will be much easier if you observe the following guidelines: ■ Stop immediately when you recognize a problem exists. Further action may result in data loss or damage.
Troubleshooting Preliminary checklist Consider the simplest solution first. The items in this checklist are easy to fix and yet can cause what appears to be a serious problem. ■ Make sure you turn on all peripheral devices before you turn on the computer. This includes your printer and any other external device you are using. ■ Before you attach an external device, turn the computer off. When you turn the computer back on it recognizes the new device.
Troubleshooting Software Hardware The problems may be caused by your software. If you cannot load a software package, the media may be damaged or the program might be corrupted. Try loading another copy of the software. If an error message appears while you are using a software package, check the software documentation. These documents usually include a problem solving section or a summary of error messages. Next, check any error messages in the operating system documentation.
Troubleshooting Self test When the computer starts up, the self test will be run automatically, and the following will be displayed: (This screen image is provided as an example. You may see a different image depending on the model you purchased.) This message remains on the screen for a few seconds. If the self test is successful, the computer tries to load the operating system based around how the Boot Priority option is set within the computer’s BIOS setup.
Troubleshooting AC power If you have trouble turning on the computer with the AC adapter connected, check the DC IN indicator. Refer to Chapter 6, Power and Power-Up Modes, for more information. Problem Procedure AC adapter doesn't power the computer (DC IN indicator does not glow green or blue (depending the model you purchased)). Check the connections. Make sure the cord is firmly connected to the computer and a power outlet. Check the condition of the cord and terminals.
Troubleshooting Problem Procedure Battery doesn't charge when the AC power cord is attached. (Battery indicator does not glow amber.) If the battery is completely discharged, it will not begin charging at once. Wait a few minutes. If the battery still does not charge, make sure the outlet is supplying power. Plug in an appliance and see if it works. If it doesn't, try another power source. Check whether the battery is hot or cold. If the battery is too hot or too cold, it will not charge properly.
Troubleshooting Problem Procedure Output to screen is garbled. Make sure the software you are using is not remapping the keyboard. Remapping involves reassigning the meaning of each key. See your software's documentation. If you are still unable to use the keyboard, consult your dealer. Problem Procedure Lines appear broken. Check if you are in DOS mode. In DOS, lines may appear broken, because of the LCD screen's higher resolution. The Windows display should appear normal.
Troubleshooting Memory Card Refer also to Chapter 8, Optional Devices. Problem Procedure Memory card error occurs Re-seat the memory card to make sure it is firmly connected. Check the card's documentation. If problems persist, contact your dealer. Wireless LAN If the following procedures do not restore LAN access, consult your LAN administrator. For more information on wireless communication, refer to Chapter 4, Operating Basics.
Troubleshooting Problem Procedure No display Try adjusting the contrast and brightness controls on the external monitor. Press hotkeys Fn + F5 to change the display priority and make sure it is not set for the internal display. Display error occurs Check that the cable connecting the external monitor to the computer is attached firmly. If problems persist, contact your dealer. Monitor goes into panning mode Check your monitor specification.
Troubleshooting Problem Procedure Double-clicking does not work Try changing the double-click speed setting in the mouse control utility. 1. Open the Control Panel, select the Mouse icon and press Enter. 2. Click the Buttons tab. 3. Set the double-click speed as instructed and click OK. The mouse pointer moves too fast or too slow Try changing the speed setting in the mouse control utility. 1. Open the Control Panel, select the Mouse icon and press Enter. 2. Click the Pointer Options tab. 3.
Troubleshooting LAN Problem Procedure Cannot access LAN or the Wake up on LAN feature does not work Check for a firm cable connection between the LAN hub. Make sure the AC adapter is connected. You cannot access a LAN using the computer's battery power. If problems persist, consult your LAN administrator.
Troubleshooting Modem Problem Procedure Communication software can't initialize the modem Make sure the computer's internal modem settings are correct. Refer to Phone and Modem Options Properties in the Control Panel. You can hear a dial tone If the call is going through a PBX machine, make but can't make a call sure the communication application's tone dial detection feature is disabled.
Troubleshooting DVD Super Multi drive supporting ±R Double Layer For more information, refer to Chapter 4, Operating Basics. Problem Procedure You cannot access a disc in the drive Make sure the drive's drawer is securely closed. Press gently until it clicks into place. Open the drawer and make sure the disc is properly seated. It should lie flat with the label facing up. A foreign object in the drawer could block laser light from reading the disc. Make sure there is no obstruction.
Troubleshooting Problem Procedure Cannot write correctly If you have trouble writing, make sure you are observing the following precautions: ■ Use only media recommended by TOSHIBA. ■ Do not use the mouse or keyboard during writing. ■ Use only the software supplied with the computer for recording. ■ Do not run or start other software during writing. ■ Do not jar the computer during writing. ■ Do not connect/ disconnect external devices or install/remove internal cards during writing.
Troubleshooting Problem Procedure Some discs run The software or hardware configuration may be correctly, but others do causing a problem. Make sure the hardware not configuration matches your software's needs. Check the disc's documentation. Check the type of disc you are using.
Troubleshooting Real Time Clock Problem Procedure The following message The RTC battery charge has become exhausted, is displayed on the LCD: you should set the date and time in within the BIOS setup screen through the following steps: RTC battery is 1. Press [F1] key. BIOS setup will boot up. low or CMOS checksum is 2. Press [F2] to set the date in [System Date]. inconsistent. 3. Press [F2] to set the time in [System Time]. Press [F2] key to set Date/ Time.
Chapter 10 Disclaimers This chapter states the Disclaimer(s) information applicable to TOSHIBA computers. CPU Central Processing Unit ("CPU") Performance Disclaimer.
Disclaimers Under some conditions, your computer product may automatically shutdown. This is a normal protective feature designed to reduce the risk of lost data or damage to the product when used outside recommended conditions. To avoid risk of lost data, always make back-up copies of data by periodically storing it on an external storage medium. For optimum performance, use your computer product only under recommended conditions. Read additional restrictions in your product documentation.
Disclaimers Maximum brightness is only available when operating in AC power mode. The screen will dim when the computer is operated on battery power and you will not be able to increase the brightness of the screen. Wireless LAN The transmission speed over the wireless LAN and the distance over which wireless LAN can reach may vary depending on surrounding electromagnetic environment, obstacles, access point design and configuration, and client design and software/hardware configurations.
Appendix A Specifications This appendix summarizes the computer's technical specifications. Dimensions 360mm (W) × 263mm (D) × 38.5mm (H. Max.) 360mm 263mm 38.
Specifications Weight Starting at 2.72kg / 5.99lbs* * Weight may vary depending on product configuration, vendor components, manufacturing variability and options selected.
Specifications User’s Manual Communication Speed Data transmission and reception 300/1200/2400/4800/7200/9600/12000/14400/ 16800/19200/21600/24000/26400/28800/31200/ 33600 bps Data reception only with V.90/V.92 28000/29333/30666/32000/33333/34666/36000/ 37333/38666/40000/41333/42666/44000/45333/ 46666/48000/49333/50666/52000/53333/54666/ 56000 bps Fax: 2400/4800/7200/9600/12000/14400 bps Error correcting MNP class 4 and ITU-T V.42 Data compression MNP class 5 and ITU-T V.
Appendix B Display Modes This appendix contains a table listing all the display modes when the display is set to an external monitor.
Display Modes Displaying movies on a TV or CRT This section describes how to set up your system to display movies simultaneously on your computer's LCD and on an external TV or CRT monitor. Follow the steps below. For the ATI Graphics Controller 1. 2. 3. 4. User’s Manual Open the Control Panel and click Display Select the Settings tab and click Advanced. Click the Displays tab. Select the external display device you wish to use.
Display Modes 5. In the properties box, if any additional options are available for your particular device, set them to your liking. 6. Finally, click the ATI Overlay tab to adjust the video overlay properties. 7. Click Setting tab. 8. Click the Graphic Properties button and choose TV.
Display Modes For the Intel Graphics Controller 1. Click Start Control Panel Appearance and Themes. 2. Choose Display to open the Display Properties dialog box. 3. Click Setting tab. 4. Click the Advanced button and choose Intel® Graphics Media Accelerator Driver.
Display Modes 5. Click the Graphic Properties button and choose TV. 6. Adjusting the TV settings.
Appendix C AC Power Cord and Connectors The power cord's AC input plug must be compatible with the various international AC power outlets and the cord must meet the standards for the country/region in which it is used. All cords must meet the following specifications: Length: Minimum 2 meters Wire size: Minimum 0.75 mm2 Current rating: Minimum 2.5 amperes Voltage rating: 125 or 250 VAC (depending on country/region's power standards) Certification agencies U.S.
AC Power Cord and Connectors In Europe, two conductors power cord must be VDE type, H05VVH2-F or H03VVH2-F and for three conductors power cord must be VDE type, H05VV-F. For the United States and Canada, two pin plug configuration must be a 2-15P (250V) or 1-15P (125V) and three pin plug coniguration must be 6-15P (250V) or 5-15P (125V) as designated in the U. S. National Electrical code handbook and the Canadian Electrical Code Part II. The following illustrations show the plug shapes for the U. S. A.
Appendix D If your computer is stolen Always take care of your computer and try to prevent it from being stolen. You are the owner of a valuable technical device, which may be highly attractive to thieves, so please do not leave it unattended in a public place. To further help protect against theft, security cables can be bought for use with your notebook when it is being used at home or in the office. Make a note of your computer’s machine type, model number, and serial number, and put it in a safe place.
If your computer is stolen To register the theft online, please follow these procedures: ■ Visit www.toshiba-europe.com on the Internet. In the product area, choose Computer Systems. ■ In the Computer Systems page, open the Support & Downloads menu and choose the Stolen Units Database option. Your entries are used to track your computer at our service points. TOSHIBA Theft Registration Send to: TOSHIBA Europe GmbH Technical Service and Support Leibnizstr.
Glossary The terms in this glossary cover topics related to this manual. Alternate naming is included for reference.
Glossary MS-DOS: Microsoft Disk Operating System PCI: peripheral component interconnect RAM: random access memory ROM: read only memory RTC: real time clock SCSI: small computer system interface TFT: thin-film transistor USB: Universal Serial Bus VESA: Video Electronic Standards Association VGA: video graphics array WXGA: wide extended graphics array A adaptor: A device that provides an interface between two dissimilar electronic devices.
Glossary C cache memory: High speed memory which stores data that increases processor speed and data transfer rate. When the CPU reads data from main memory, it stores a copy of this data in cache memory. The next time the CPU needs that same data, it looks for it in the cache memory rather than the main memory, which saves time. The computer has two cache levels. Level one is incorporated into the processor and level two resides in external memory.
Glossary CRT: Cathode Ray Tube. A vacuum tube in which beams projected on a fluorescent screen-producing luminous spots. An example is the television set. cursor: A small, blinking rectangle or line that indicates the current position on the display screen. D DC: Direct Current. Electric current that flows in one direction. This type of power is usually supplied by batteries. default: The parameter value automatically selected by the system when you or the program do not provide instructions.
Glossary format: The process of readying a blank disk for its first use. Formatting establishes the structure of the disk that the operating system expects before it writes files or programs onto the disk. function keys: The keys labeled F1 through F12 that tell the computer to perform certain functions. G gigabyte (GB): A unit of data storage equal to 1024 megabytes. See also megabyte. graphics: Drawings, pictures, or other images, such as charts or graphs, to present information.
Glossary J jumper: A small clip or wire that allows you to change the hardware characteristics by electrically connecting two points of a circuit. K K: Taken from the Greek word kilo, meaning 1000; often used as equivalent to 1024, or 2 raised to the 10th power. See also byte and kilobyte. KB: See kilobyte. L Light Emitting Diode (LED): A semiconductor device that emits light when a current is applied.
Glossary operating system: A group of programs that controls the basic operation of a computer. Operating system functions include interpreting programs, creating data files, and controlling the transmission and receipt (input/output) of data to and from memory and peripheral devices. output: The results of a computer operation. Output commonly indicates data. 1) printed on paper, 2) displayed at a terminal, 3) sent through the serial port of internal modem, or 4) stored on some magnetic media.
Glossary stop bit: One or more bits of a byte that follow the transmitted character or group codes in asynchronous serial communications. system disk: A disk that has been formatted with an operating system. For MS-DOS the operating system is contained in two hidden files and the COMMAND.COM file. You can boot a computer using a system disk. Also called an operating system disk. T terminal: A typewriter-like keyboard and CRT display screen connected to the computer for data input/output.
