Satellite® A130/A135 Series User’s Guide If you need assistance: ❖ Toshiba’s Support Web site pcsupport.toshiba.com ❖ Toshiba Global Support Centre Calling within the United States (800) 457-7777 Calling from outside the United States (949) 859-4273 For more information, see “If Something Goes Wrong” on page 168 in this guide.
Handling the cord on this product will expose you to lead, a chemical known to the State of California to cause birth defects or other reproductive harm. Wash hands after handling. Model: Satellite® A130/A135 Series Recordable and/or ReWritable Drive(s) and Associated Software Warranty The computer system you purchased may include Recordable and/or ReWritable optical media drive(s) and associated software, among the most advanced data storage technologies available.
Critical Applications The computer you have purchased is not designed for any “critical applications.” “Critical applications” means life support systems, medical applications, connections to implanted medical devices, commercial transportation, nuclear facilities or systems or any other applications where product failure could lead to injury to persons or loss of life or catastrophic property damage.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: ❖ This device may not cause harmful interference. ❖ This device must accept any interference received, including interference that may cause undesired operation. Contact either: ❖ Toshiba’s Support Web site at pcsupport.toshiba.com.
Connection to party line service is subject to state tariffs. Contact the state public utility commission, public service commission or corporation commission for information. Telephone Company Procedures The goal of the telephone company is to provide you with the best service it can. In order to do this, it may occasionally be necessary for them to make changes in their equipment, operations or procedures.
Alarm Equipment If your home has specially wired alarm equipment connected to the telephone line, ensure the installation of this equipment does not disable your alarm equipment. If you have questions about what will disable alarm equipment, consult your telephone company or a qualified installer. Instructions for IC CS-03 Certified Equipment 1 NOTICE: The Industry Canada label identifies certified equipment.
Wireless Interoperability The TOSHIBA Wireless LAN Mini PCI Card products are designed to be interoperable with any wireless LAN product that is based on Direct Sequence Spread Spectrum (DSSS) radio technology, and is compliant to: ❖ The IEEE 802.11 Standard on Wireless LANs (Revision A/B/G), as defined and approved by the Institute of Electrical and Electronics Engineers. ❖ The Wireless Fidelity (Wi-Fi®) certification as defined by the Wi-Fi Alliance.
and committees of scientists who continually review and interpret the extensive research literature. In some situations or environments, the use of Wireless LAN may be restricted by the proprietor of the building or responsible representatives of the organization. These situations may for example include: ❖ Using the Wireless LAN equipment on board airplanes, or ❖ In any other environment where the risk of interference to other devices or services is perceived or identified as harmful.
L’utilisation de ce dispositif est autorisée seulement aux conditions suivantes: (1) il ne doit pas produire de brouillage et (2) l’utilisateur du dispositif doit étre prêt à accepter tout brouillage radioélectrique reçu, même si ce brouillage est susceptible de compromettre le fonctionnement du dispositif. The term “IC” before the equipment certification number only signifies that the Industry Canada technical specifications were met.
VCCI Class B Information Modem Warning Notice Conformity Statement The equipment has been approved to [Commission Decision “CTR-21”] for panEuropean single terminal connection to the Public Switched Telephone Network (PSTN). However, due to differences between the individual PSTNs provided in different countries/regions the approval does not, of itself, give an unconditional assurance of successful operation on every PSTN network termination point.
Using this Equipment in Japan In Japan, the frequency bandwidth of 2,400 MHz to 2,483.5 MHz for second generation low-power data communication systems such as this equipment overlaps that of mobile object identification systems (premises radio station and specified low-power radio station). 1. Sticker Please put the following sticker on devices incorporating this product.
Device Authorization This device obtains the Technical Regulation Conformity Certification and the Technical Conditions Compliance Approval, and it belongs to the device class of radio equipment of low-power data communication system radio station stipulated in the Radio Law and the Telecommunications Business Law of Japan.
France Ireland Luxembourg Norway Switzerland Germany Italy Netherlands Portugal UK Greece Liechtenstein New Zealand Sweden USA Europe - Restrictions for use of 2.4 GHz Frequencies in European Community Countries België/ Belgique: Deutschland: France: Italia: Nederland: For private usage outside buildings across public grounds over less than 300m no special registration with IBPT/BIPT is required.
802.
❖ This device must not be operated in ad-hoc mode using channels in the 5 GHz bands in the European Community. Ad-hoc mode provides a direct communication between two client devices without a Wireless LAN Access Point. ❖ This device must be used with Access Points that have employed and activated a radar detection feature required for European Community operation in the 5 GHz bands.
802.11a (5 GHz) Australia Canada France Ireland Luxembourg Norway Switzerland Austria Denmark Germany Italy Netherlands Portugal UK Belgium Finland Greece Liechtenstein New Zealand Sweden USA Turbo Mode (5 GHz) Canada USA Approved Countries/Regions for use for the Intel® PRO/ Wireless LAN 2100 3B Mini PCI Adapter This equipment is approved to the radio standard by the countries/regions in the following table. Do not use this equipment except in the countries/regions in the following table.
Approved Countries/Regions for use for the Toshiba Mini PCI Wireless LAN Card This equipment is approved to the radio standard by the countries/regions in the following table. Do not use this equipment except in the countries/regions in the following table.
802.11a (5 GHz) Australia Chile Indonesia New Zealand USA Brunei Hong Kong Malaysia Saudi Arabia Venezuela Canada India Mexico Taiwan Vietnam Bluetooth® Wireless Technology Interoperability Bluetooth® Cards from TOSHIBA are designed to be interoperable with any product with Bluetooth® wireless technology that is based on Frequency Hopping Spread Spectrum (FHSS) radio technology, and is compliant to: ❖ Bluetooth® Specification as defined and approved by The Bluetooth Special Interest Group.
computers/tnt/bluetooth.htm in Europe or pcsupport.toshiba.com in the United States for more information. Approved Countries/Regions for use (Bluetooth® wireless technology) Bluetooth® Card from Toshiba equipment is approved to the radio standard by the countries/regions in the following table. Do not use this equipment except in the countries/regions in the following table.
In some situations or environments, the use of Bluetooth® wireless technology may be restricted by the proprietor of the building or responsible representatives of the organization. These situations may for example include: ❖ Using the equipment with Bluetooth® wireless technology on board airplanes, or ❖ In any other environment where the risk of interference to other devices or services is perceived or identified as harmful.
The legal communications mentioned in the above item refer to radio communications operated in accordance with telecommunication laws and regulations. Low power radio frequency electric machinery shall resist against interference from legal communications or from industrial, scientific and medical radio emission electric machinery. Using this Equipment in Japan In Japan, the frequency bandwidth of 2,400 MHz to 2,483.
3. TOSHIBA Direct PC Monday – Friday: 10:00 – 17:00 Toll Free Tel: 0120-15-1048 Direct Dial: 03-3457-4850 Fax: 03-3457-4868 Device Authorization This device obtains the Technical Regulation Conformity Certification, and it belongs to the device class of radio equipment of low-power data communication system radio station stipulated in the Radio Law of Japan.
Location of the Required Label (Sample shown below. Location of the label and manufacturing information may vary.) This appliance contains a laser system and is classified as a CLASS 1 LASER PRODUCT. To use this model properly, read the user’s guide carefully and keep it for your future reference. Never attempt to disassemble, adjust or repair a HD DVD, CD/DVD drive, CD-RW drive, Multi-drive or any other optical drive. You could damage the drive.
Export Administration Regulation This document contains technical data that may be controlled under the U.S. Export Administration Regulations, and may be subject to the approval of the U.S. Department of Commerce prior to export. Any export, directly or indirectly, in contravention of the U.S. Export Administration Regulations is prohibited. Notice The information contained in this manual, including but not limited to any product specifications, is subject to change without notice.
Trademarks Satellite is a registered trademark of Toshiba America Information Systems, Inc. and/or Toshiba Corporation. Microsoft Windows and Windows Vista are either registered trademarks or trademarks of Microsoft Corporation in the United States and/or other countries. DirectX, Active Desktop, DirectShow, and Windows Media are registered trademarks of Microsoft Corporation. ConfigFree is a trademark of Toshiba Corporation. Wi-Fi is a registered trademark of the Wi-Fi Alliance.
Contents Introduction................................................................................ 33 This guide ...............................................................34 Safety icons ............................................................35 Other icons used...............................................35 Other documentation ..............................................36 Service options .......................................................36 Chapter 1: Getting Started..................
Contents 27 Using the computer for the first time ......................45 Opening the display panel .................................45 Your computer’s features and specifications ....46 Turning on the power .......................................46 Adding memory (optional) ......................................47 Installing a memory module .............................48 Removing a memory module............................53 Checking total memory .....................................
Contents Using a computer lock ......................................83 Chapter 2: Learning the Basics................................................. 84 Computing tips .......................................................84 Using the keyboard .................................................85 Character keys .................................................86 Making your keyboard emulate a full-size keyboard .....................................................86 Ctrl, Fn, and Alt keys ...........
Contents 29 Chapter 3: Mobile Computing.................................................102 Toshiba’s energy-saver design..............................102 Running the computer on battery power ..............102 Battery Notice .................................................103 Power management ........................................104 Using additional batteries ...............................104 Charging batteries.................................................104 Charging the main battery............
Contents Surfing the Internet.........................................129 Internet features..............................................129 Uploading to, and downloading files from, the Internet ....................................................130 Exploring audio features .......................................130 Recording sounds...........................................130 Using external speakers or headphones..........131 Using PC Cards.....................................................
Contents 31 Fingerprint Logon ...........................................156 Power-on Security ..........................................156 Control Center.................................................157 Password Bank ...............................................159 Care and maintenance of your fingerprint reader .......................................................162 Fingerprint reader limitations ..........................164 ConfigFree™..........................................................
Contents Data and system configuration backup in the Windows® operating system ...................191 If you need further assistance...............................195 Before you contact Toshiba ............................195 Contacting Toshiba .........................................196 Other Toshiba Internet Web sites..........................197 Toshiba’s worldwide offices..................................197 Appendix A: Hot Keys/TOSHIBA Cards..................................199 Hot Key Cards ...
Introduction Welcome to the world of powerful, portable, multimedia computing. With your Toshiba notebook computer, your work and entertainment can accompany you wherever you go. NOTE This notebook is compatible with European Union Directive 2002/ 95/EC, Restriction of the use of certain Hazardous Substances in electrical and electronic equipment (RoHS), which restricts use of lead, cadmium, mercury, hexavalent chromium, PBB, and PBDE.
Introduction This guide NOTE The product specifications and configuration information are designed for a product Series. Your particular model may not have all the features and specifications listed or illustrated. For more detailed information about the features and specifications on your particular model, please visit Toshiba’s Web site at pcsupport.toshiba.com.
Introduction Safety icons 35 Safety icons This manual contains safety instructions that must be observed to avoid potential hazards that could result in personal injuries, damage to your equipment, or loss of data. These safety cautions have been classified according to the seriousness of the risk, and icons highlight these instructions as follows: Indicates an imminently hazardous situation which, if not avoided, will result in death or serious injury.
Introduction Other documentation Other documentation Your computer comes with the following documentation: ❖ An electronic version of the user’s guide (this document) ❖ It may also contain guides for other programs that may come with your system. For accessory information, visit Toshiba’s Web site at accessories.toshiba.com. Service options Toshiba offers a full line of optional service programs to complement its limited warranty.
Chapter 1 Getting Started This chapter provides tips for working comfortably, summarizes how to connect components, and explains what to do the first time you use your notebook computer. Selecting a place to work Your computer is portable and designed to be used in a variety of circumstances and locations. Creating a computer-friendly environment Place the computer on a flat surface that is large enough for the computer and any other items you are using, such as a printer.
Getting Started Selecting a place to work ❖ Extreme heat, cold, or humidity. ❖ Liquids and corrosive chemicals. Keeping yourself comfortable The Toshiba Instruction Manual for Safety and Comfort, that shipped with your computer, contains helpful information for setting up your work environment and tips for working comfortably throughout the day. Precautions Your computer is designed to provide optimum safety and ease of use, and to withstand the rigors of travel.
Getting Started Selecting a place to work ❖ 39 Never turn off the computer if a drive light indicates a drive is active. Turning off the computer while it is reading from or writing to a disk/disc or flash media may damage the disk/disc or flash media, the drive, or both. ❖ Keep the computer and disks away from objects that generate strong magnetic fields, such as large stereo speakers. Information on disks is stored magnetically. Placing a magnet too close to a disk can erase important files.
Getting Started Setting up your computer Setting up your computer TECHNICAL NOTE: You must complete all setup steps up to and including “Setting up your software” on page 40 before adding external or internal components to your computer. These components include, but are not limited to, a mouse, keyboard, printer, memory, and PC Cards. Your computer contains a rechargeable main battery that needs to be charged before you can use it.
Getting Started Registering your computer with Toshiba 41 Registering your computer with Toshiba Product registration is strongly recommended, and allows Toshiba to send you periodic updates, announcements, and special offers applicable to your product. Product registration can be completed during the initial start up process of your computer. If you decide not to register at that time, you can either double-click the Toshiba Registration icon on your desktop or go to the Toshiba Web site at www.
Getting Started Connecting to a power source Connecting to a power source Your computer requires power to operate. Use the power cord/cable and AC adaptor to connect the computer to a live electrical outlet, or to charge the computer’s battery. Never pull on a power cord/cable to remove a plug from a socket. Always grasp the plug directly. Failure to follow this instruction may damage the cord/cable, and/or result in a fire or electric shock, possibly resulting in serious injury.
Getting Started Connecting to a power source 43 To connect AC power to the computer: 1 Connect the power cord/cable to the AC adaptor. (Sample Illustration) Connecting the power cord/cable to the AC adaptor Handling the cord on this product will expose you to lead, a chemical known to the State of California to cause birth defects or other reproductive harm. Wash hands after handling. _ + 2 Plug the AC adaptor cord into the DC-IN on the back of the computer.
Getting Started Charging the main battery The computer’s main battery light gives you an indication of the main battery’s current charge: NOTE ❖ Glows amber while the main battery is being charged (AC adaptor connected) ❖ Glows blue or green (depending on your model) when the main battery is fully charged ❖ Is unlit when the main battery has discharged, the battery is not charging, or the AC adaptor is not plugged into the computer or AC outlet ❖ Flashes amber when the main battery charge is l
Getting Started Using the computer for the first time NOTE 45 Battery life and charge time may vary depending on the applications, power management settings, and features used. Using the computer for the first time The computer is now ready for you to turn it on and begin using it. Opening the display panel 1 Slide the display latch to the right. 2 Lift the display panel.
Getting Started Using the computer for the first time Small bright dots may appear on your screen display when you turn on your computer. Your display contains an extremely large number of thin-film transistors (TFT) and is manufactured using highprecision technology. Any small bright dots that may appear on your display are an intrinsic characteristic of the TFT manufacturing technology. Over a period of time, and depending on the usage of the computer, the brightness of the screen will deteriorate.
Getting Started Adding memory (optional) 3 47 Press and hold the power button in until the power button and the on/off light on the system indicator panel glows blue or green (depending on your model)—about one second. (Sample Illustration) Turning on the power The preinstalled operating system will load automatically. When you turn on the computer for the first time, do not turn off the power again until the operating system has loaded completely.
Getting Started Adding memory (optional) Installing a memory module Memory modules can be installed in the memory module slots on the base of the computer. You will need a small Phillips screwdriver for this procedure. If the computer has been running recently, the memory module may be hot. The surrounding area may also be hot. Allow the module to cool to room temperature before replacing it. Avoid touching the cover, the module, and the surrounding area before they have cooled.
Getting Started Adding memory (optional) 2 49 Click Shut Down. The operating system turns off the computer. 3 Unplug and remove any cables connected to the computer, including the AC adaptor. 4 Remove the main battery. For information on removing the main battery, see “Removing the battery from the computer” on page 113. 5 Close the display panel and turn the computer upside down to locate the memory module slot cover.
Getting Started Adding memory (optional) 6 Using a small Phillips screwdriver, loosen the captive screw that secures the memory module slot cover. Front of computer (Sample Illustration) Removing the memory module slot cover 7 Remove the memory module slot cover. 8 Place the screw and the cover in a safe place so that you can retrieve them later. Static electricity can damage the memory module.
Getting Started Adding memory (optional) NOTE 51 If your system has the memory modules stacked on top of one another, you must remove the top module first before removing/installing the bottom module. 11 Pick up the memory module by its sides, avoiding any contact with its connector. Position the module toward the socket, aligning the connector’s notch with the matching key in the socket.
Getting Started Adding memory (optional) cutouts in the side of the module. If the latches and cutouts do not line up correctly, repeat steps 12-13. latch latch (Sample Illustration) Pressing down on the memory module Do not force the memory module into position. The memory module should be completely inserted into the socket and level when secured in place.
Getting Started Adding memory (optional) 53 TECHNICAL NOTE: You must have at least one memory module installed for the computer to work. You can now continue setting up the computer. When the operating system has loaded, you can verify that the computer has recognized the additional memory module. If you are adding extra memory after setting up the computer, verify that the computer has recognized it correctly as described in “Checking total memory” on page 56.
Getting Started Adding memory (optional) NOTE The following screen appears when you turn on the power: If “Start Windows® Normally” is highlighted, then press Enter. If one of the Safe Mode options is highlighted, it is best to press Enter to go into Safe Mode, then shut down and restart the system, at which time Windows® should boot back up normally. When Safe Mode is suggested, this could be a sign that you may need to scan your hard drive for errors or defragment the drive.
Getting Started Adding memory (optional) 3 55 Gently lift the memory module to a 30-degree angle and slide it out of the slot. Memory slots Front of computer (Sample Illustration) Removing the memory module 4 Replace the memory module slot cover and secure it using the screw. 5 Re-insert the main battery. For more information on inserting the main battery, see “Inserting a charged battery” on page 115. 6 Turn the computer right side up. 7 Reconnect the cables. 8 Restart the computer.
Getting Started Hard Drive Recovery Utilities Checking total memory When you add or remove a memory module, you can check that the computer has recognized the change. To do this: 1 Click Start, Control Panel, and then System. 2 The total memory is displayed under Memory (RAM).
Getting Started Hard Drive Recovery Utilities ❖ 57 Reinstall drivers and applications which were bundled with your computer Creating Recovery CDs/DVDs Depending on your system configuration, you may be able to copy the Hard Drive Recovery Utilities to CD or DVD which gives you the ability to recover your hard disk drive and recover your system if the hard drive recovery partition has been deleted or the hard disk has been replaced on your computer.
Getting Started Hard Drive Recovery Utilities 3 Select the items you want to copy by clicking the check box next to the item’s Name—recovery files, applications (original bundled drivers and applications), or both the recovery files and applications. 4 Click Create. 5 Insert the first blank CD or DVD into your writable optical drive when prompted. 6 Follow the on-screen prompts for completing the copy process.
Getting Started Hard Drive Recovery Utilities 59 Hard Disk Drive Recovery using the recovery partition You have the options of recovering your system using the Hard Drive Recovery partition to the factory-set default, or recovering just your C: drive and leaving other partitions (for example, a D: drive) intact, or changing the size of your C: drive and then recovering it. To recover your hard disk drive using the utilities stored on your computer’s HDD: 1 Make sure the computer is turned off.
Getting Started Hard Drive Recovery Utilities Recovering the original factory image (recommended recovery method) Recovering a hard disk drive to its out of box state deletes all partitions on the hard disk drive and your information will be lost. Be sure to save your work to external media first. 1 On the Toshiba Recovery Wizard screen, select Recovery of Factory Default Software, then click Next. The Recovery of Factory Default Software screen appears.
Getting Started Hard Drive Recovery Utilities 61 Erasing the hard disk The Recovery Wizard allows you to delete all data and partitions from the hard disk. To delete the data and partitions from your hard disk: 1 On the Toshiba Recovery Wizard screen, select Erase the hard disk, then click Next. 2 The next screen lists the two methods you can choose: ❖ Delete all data and partitions from the hard disk—This option deletes all of the data on the hard disk without overwriting the HDD.
Getting Started Hard Drive Recovery Utilities Recovering the C: partition of the HDD without changing the current partition size Recovering the C: drive to its factory default setting reformats your drive and your information on the recovered drive will be lost. Be sure to save your work to external media first. If you have created other partitions (for example, a D: drive) those partitions and any information on them will not be affected and will remain intact.
Getting Started Hard Drive Recovery Utilities NOTE 63 The size of the C: drive will display on the progress bar as you make your selections. 4 Click Next to begin the restoration. Once complete, a message displays that the HDD has been recovered. 5 Press any key on your keyboard to restart the computer. Hard Disk Drive Recovery using the Recovery media If you need to recover your computer to its default factory state, you can rebuild the system using your Hard Drive Recovery Utilities.
Getting Started Using the TouchPad™ Checking the HDD operating status After restoring your hard disk drive, you can check its status as follows: 1 Click Start. 2 Right-click Computer. 3 Select Manage. 4 Click Disk Management. 5 Highlight the hard disk drive in the Volume list to display its status in the lower portion of the screen.
Getting Started Using the TouchPad™ NOTE 65 Because the TouchPad is much smaller than the display screen, moving your cursor across the screen often means having to move your finger several times across the TouchPad in the preferred direction. Once you have positioned your cursor, you can click it into place by either double-tapping the TouchPad or clicking the control buttons.
Getting Started Using the Dual Mode Pad Using the Dual Mode Pad (Available on certain models) Using Dual Mode The Dual Mode feature allows you to switch between Cursor Mode (the default mode) and Button Mode. In Button Mode, you can use the virtual buttons on the Dual Mode Pad which provide convenient shortcuts to frequently used applications. You can also use the volume control bar to adjust the system volume quickly and easily.
Getting Started Using the Dual Mode Pad 67 In order to use the virtual buttons you must first enable Dual Mode in the Mouse Properties dialog box. After that, you can use the virtual buttons as follows: 1 Tap the mode switch button to enable the virtual buttons. 2 Tap the virtual button assigned to the application you wish to launch, or slide your finger on the volume control bar to adjust the volume to the desired level.
Getting Started Using external display devices unassigned by default. In order to use one of these buttons, you must first configure that button so that it is associated with a function. To configure a virtual button: 1 Perform steps 1-5 in “Enabling Dual Mode” on page 67. 2 Select the virtual button you wish to configure. 3 Select the desired options, and then click OK. 4 Click OK. 5 Click OK to close the Mouse Properties window.
Getting Started Using external display devices 5 69 Then click OK. Directing the display output when you turn on the computer Once you have connected an external display device, you can choose to use the internal display only, the external device only, or both simultaneously. The quickest way to change the display output settings is to use the display hot key (Fn + F5): 1 Press Fn and F5 simultaneously. 2 While holding down Fn, press F5 repeatedly until the setting you want takes effect.
Getting Started Using an external keyboard TECHNICAL NOTE: To use one of the simultaneous modes, you must set the resolution of the internal display panel to match the resolution of the external display device. The external display device must support a resolution of 800 x 600 or higher. Using an external keyboard If you prefer to use a full-size keyboard, you can attach one to your computer. The computer’s USB ports support any USB-compatible keyboard.
Getting Started Connecting a printer 71 If your printer does not support Plug and Play, you can set up the printer as described in “Setting up a printer” on page 71. To connect a printer to your computer: 1 Connect the printer cable to the printer and then connect the other end to one of the computer’s USB ports. 2 Plug the printer’s power cable into a live AC outlet. Setting up a printer NOTE Some printers require a specific installation process.
Getting Started Connecting an optional external diskette drive Connecting an optional external diskette drive Some operations, such as creating a password service diskette, require a diskette drive designed for use with 3.5-inch diskettes. (Sample Illustration) Optional external USB diskette drive To connect an optional external USB diskette drive, connect the cable to one of the computer’s USB ports.
Getting Started Turning off the computer 73 Options for turning off the computer Depending on the operating system installed, you have more than one option available for turning off the computer: Shut Down, Hibernate, and Sleep. Each option has its advantages. ❖ Use the Shut Down or Hibernate command if you will not be using the computer for several days or if you must turn off your computer. You must turn off your computer in order to upgrade your computer’s internal hardware (such as memory).
Getting Started Turning off the computer For information on how to use and configure Hibernation mode see “Using and configuring Hibernation mode” on page 77. Sleep mode The Sleep command places the computer into a power-saving mode. Sleep saves the current state of the computer to memory so that, when you restart the computer, you can continue working from where you left off.
Getting Started Turning off the computer 75 Using the Shut Down command The Shut down command completely shuts down the computer without saving your work or the current state of the computer. This command closes all open programs, shuts down the operating system, and then turns off your computer. Use the following steps to turn off your computer using the Shut Down command: 1 Click Start, and then click the arrow next to the Lock button in the lower-right part of the Start menu.
Getting Started Turning off the computer 3 Click Change advanced power settings. The Advanced settings tab of the Power Options window appears. (Sample Image) Advanced settings tab of Power Options screen 4 Click Power buttons and lid to display the actions that you can configure. 5 Select the options you want from the drop-down lists. ❖ Lid close action Set this option to Shut down if you want the computer to shut down when you close the display panel.
Getting Started Turning off the computer 77 Restarting your computer To start the computer up again, press the power button until the on/ off light glows blue or green (depending on your model). If you turn off the computer by closing the display panel, you can start it again by opening the display panel.
Getting Started Turning off the computer 3 Click Change advanced power settings. The Advanced settings tab of the Power Options window appears. (Sample Image) Advanced settings tab of Power Options screen 4 Click Power buttons and lid to display the actions that you can configure. 5 Select Hibernate for the options you want. ❖ Lid close action Set this option to Hibernate if you want the computer to go into Hibernation mode when you close the display panel.
Getting Started Turning off the computer 79 Starting again from Hibernation mode To start up the computer from Hibernation mode, press the power button until the on/off light glows blue or green (depending on your model). The computer returns to the screen(s) you were using. If you put the computer in Hibernation mode by closing the display panel, you can start it again by opening the display panel.
Getting Started Turning off the computer 1 Click Start, Control Panel, System and Maintenance, and then Power Options. The Power Options window appears. 2 Click Change plan settings under the power plan to be customized. The Edit Plan Settings window appears. (Sample Image) Edit Plan Settings screen 3 To change the amount of time after which the computer enters Sleep mode: ❖ Under Put the computer to sleep, select the desired amount of time in both the On battery and Plugged in categories.
Getting Started Turning off the computer 4 81 Click Change advanced power settings. The Advanced settings tab of the Power Options window appears. (Sample Image) Advanced settings tab of Power Options screen 5 Click Power buttons and lid to display the actions that you can configure. 6 Select Sleep for the options you want. ❖ Lid close action Set this option to Sleep if you want the computer to go into Sleep mode when you close the display panel.
Getting Started Customizing your computer’s settings Starting again from Sleep mode To start up the computer from Sleep mode, press the power button until the on/off light glows blue or green (depending on your model). The computer returns to the screen(s) you were using. If you place the computer in Sleep mode by closing the display panel, you can start it again by opening the display panel.
Getting Started Caring for your computer 83 Do not pick up the computer by its display panel or by the back (where the ports are located). Doing so could damage the system. Using a computer lock You may want to secure your computer to a heavy object such as your desk. The easiest way to do this is to purchase an optional computer lock cable. For more information on purchasing a cable lock, visit accessories.toshiba.com.
Chapter 2 Learning the Basics This chapter gives some computing tips and provides important information about basic features. Computing tips ❖ Save your work frequently. Your work stays in the computer’s temporary memory until you save it to the disk. If the network you are using goes down and you must restart your computer to reconnect, or your battery runs out of charge while you are working, you will lose all work since you last saved. See “Saving your work” on page 91 for further information.
Learning the Basics Using the keyboard ❖ Use Error-checking and Disk Defragmenter regularly to conserve disk space and improve performance. ❖ Scan all new files for viruses. 85 This precaution is especially important for files you receive via diskette, email, or download from the Internet. ❖ Take frequent breaks to avoid repetitive-motion injuries and eyestrain. ❖ Do not turn off the computer if a drive indicator light indicates a drive is active.
Learning the Basics Using the keyboard Character keys Typing with the character keys is very much like typing on a typewriter, except that: ❖ The space bar creates a space character instead of just passing over an area of the page. ❖ The lowercase letter l (el) and the number 1 are not interchangeable. ❖ The uppercase letter O and the number 0 are not interchangeable.
Learning the Basics Using the keyboard 87 Ctrl, Fn, and Alt keys Ctrl Fn Alt (Sample Illustration) Ctrl, Fn, and Alt keys The Ctrl, Fn, and Alt keys do different things depending on the program you are using. For more information, see your program documentation. Function keys The function keys (not to be confused with the Fn key) are the 12 keys at the top of the keyboard.
Learning the Basics Using the keyboard Overlay keys The keys with gray numbers and symbols on the front of them form the numeric and cursor overlay. This overlay lets you enter numeric data or control the cursor as you would using the 10-key keypad on a desktop computer’s keyboard. Home PgUp End (Sample Illustration) Numeric and cursor control overlay Using the overlay to type numeric data The keys with the numbers on their right front are the numeric overlay keys.
Learning the Basics Starting a program 89 Starting a program The easiest way to start a program is to double-click the name of the file that contains the information you want to work on. To find the file, use the Start menu or Windows® Explorer. If you prefer to open the program first, you have four options.
Learning the Basics Starting a program Starting a program from Windows® Explorer If a program is not listed in the All Programs menu, you can start it from Windows® Explorer. Windows® Explorer gives you a view of your computer’s contents as a hierarchy or “tree.” You can easily see the contents of each drive and folder on your computer. To use this method, you should know the file name and location of the program’s executable file (this file ends with .exe).
Learning the Basics Saving your work 91 Starting a program using the Start Search field This example uses the Start menu’s Start Search field to start WordPad: 1 Click Start to display the Start menu. The Start Search field appears at the bottom of the Start menu. Start Search field Arrow (Sample Image) Start Search field in Start menu 2 Start typing the program’s name in the Start Search field. As you type, all matching files and programs are displayed in the Start menu.
Learning the Basics Saving your work Saving files 1 In your Windows®-based application, click File, and then Save. If you are working with a document that already has a file name, this is all you need to do. If you created a new document, your program displays a Save As dialog box. Use this dialog box to specify where to store the document and to give it a file name. (Sample Image) Save As dialog box 2 Choose the drive and folder where you want your file to be stored.
Learning the Basics Printing your work 93 Using a file extension Most programs assign an extension to the file name that identifies the file as being created in the program with a particular format. For example, Microsoft® Word saves files with a .doc extension. Any file name with an extension of “.doc” is assumed to be a Microsoft® Word file. Creating your own extension is usually unwise, since the program is unlikely to recognize a strange extension and may refuse to handle your file correctly.
Learning the Basics Backing up your work 3 Specify the print parameters. For example, the range of pages and number of copies to print. 4 Click Print. Backing up your work Back up all the files you create in case something happens to your computer. You can back up your files to different types of media such as CDs, DVDs, diskettes, or to a network, if available. To back up several files at one time, use the Microsoft® Windows® backup program preinstalled on the computer’s hard disk.
Learning the Basics Using the optical drive 95 Using the optical drive Optical storage has become the preferred medium for software, music, and video. Digital versatile discs (DVDs) provide a significant increase in data storage and support features that are not available on any other video platform. These features include widescreen movies, multiple language tracks, digital surround sound, multiple camera angles, and interactive menus. For these reasons, your computer may come with an optical drive.
Learning the Basics Using the optical drive Do not press the eject button or turn off the computer while the drive in-use indicator light is glowing. Doing so could damage the disc or the drive. When the disc tray is open, be careful not to touch the lens or the area around it. Doing so could cause the drive to malfunction. Manual eject hole—Use if you need to release the disc tray when the power is off.
Learning the Basics Using the optical drive 97 The Previous track button/Next track button returns to the preceding track on the disc (press the left side of the button) or skips to the following track on the disc (press the right side of the button). Inserting a compact disc To insert a compact disc into the drive: 1 Make sure the computer is turned on. The drive will not open if the computer’s power is off. 2 Make sure the drive’s in-use indicator light is off. 3 Press the drive’s eject button.
Learning the Basics Using the optical drive 6 Place the disc carefully in the disc tray, label side up. (Sample Illustration) Positioning the disc in the drive 7 Gently press the disc onto the center spindle until it clicks into place. Handle DVDs and CDs carefully, making contact only with the center hole and edge. Do not touch the surface of the disc. Do not stack discs. If you incorrectly handle the discs, you could lose data.
Learning the Basics Using the optical drive NOTE 99 When using Windows Media® Player, your system may not be able to activate Sleep or Hibernation modes. To prevent this from occurring, close Windows Media® Player before you select Sleep or Hibernation mode. Stop button Play/Pause button (Sample Image) Windows Media® Player screen The Windows Media® Player control panel works much like an ordinary compact disc player: ❖ To play the CD or to pause, click the Play/Pause button.
Learning the Basics Using the optical drive If your disc does not run using this method, try using an application that is associated with the media on the disc. For example, if it is a music CD, open Windows Media® Player and use it to select and then play the CD. For other types of media, use the associated software to open the files on the disc.
Learning the Basics Toshiba’s online resources 101 2 Pull the tray out until it is fully open, remove the disc, and place it in its protective cover. 3 Gently press the tray in to close it. Removing a disc with the computer off To remove a disc with the computer turned off: 1 Insert a slender object, such as a straightened paper clip, into the manual eject hole. The disc tray slides partially out of the drive (about 1 inch). Never use a pencil to press the manual eject button.
Chapter 3 Mobile Computing This chapter covers all aspects of using your computer while traveling. Toshiba’s energy-saver design Your computer enters a low-power suspension mode when it is not being used, thereby conserving energy and saving money in the process. It has a number of other features that enhance its energy efficiency. Many of these energy-saving features have been set by Toshiba.
Mobile Computing Running the computer on battery power 103 Battery Notice Battery life may vary considerably from specifications depending on product model, configuration, applications, power management settings and features utilized, as well as the natural performance variations produced by the design of individual components. Published battery life numbers are achieved on select models and configurations tested by Toshiba at the time of publication. Recharge time varies depending on usage.
Mobile Computing Charging batteries Power management Your computer ships with the power management options preset to a configuration that will provide the most stable operating environment and optimum system performance for both AC power and battery modes. Changes to these settings may result in system performance or stability issues. Users who are not completely familiar with the power management component of the system should use the preset configuration.
Mobile Computing Charging batteries 105 Charging the main battery To charge the main battery while it is in your computer, plug the computer into a live electrical outlet. The battery charges whether the computer is on or off. TECHNICAL NOTE: The recharging of the battery cannot occur when your computer is using all of the power provided by the AC adaptor to run applications, features, and devices.
Mobile Computing Monitoring main battery power NOTE The above error message may vary by computer model. The RTC battery does not charge while the computer is turned off even when the AC adaptor is charging the computer. The RTC battery charges when the computer is powered on. If the RTC battery is low, the real-time clock and calendar may display the incorrect time and date, or stop working.
Mobile Computing Monitoring main battery power NOTE 107 If the AC power light flashes amber during charging, either a battery pack is malfunctioning, or it is not receiving correct input from the AC power supply. Disconnect the AC power cord/cable and remove the battery pack. See “Changing the main battery” on page 113 for information on replacing the main battery.
Mobile Computing Monitoring main battery power Determining remaining battery power NOTE 1 Wait at least 16 seconds after turning on the computer before trying to monitor the remaining battery power. The computer needs this time to check the battery’s remaining capacity and perform its calculations. Highlight the power icon on the Notification Area. A pop-up message displays the remaining battery power as a percentage.
Mobile Computing Monitoring main battery power 109 Setting battery notifications You can set two notifications. Each notification can be set to alert you when a specified percentage of remaining battery power has been reached. You can also set the computer to enter Sleep mode or Hibernation mode or to completely power down when the notification goes off. To change the default notification settings: 1 Click Start, Control Panel, Mobile PC and then Power Options. The Power Options window appears.
Mobile Computing Monitoring main battery power Conserving battery power How long a fully charged battery pack lasts when you are using the computer depends on a number of factors, such as: ❖ How the computer is configured ❖ How much you use the hard disk, optical drive, diskette drives, or other optional devices ❖ Where you are working, since operating time decreases at low temperatures There are various ways in which you can conserve power and extend the operating time of your battery: ❖ Enab
Mobile Computing Monitoring main battery power 111 Power Plans You can choose a predefined Power Plan or select your own combination of power options. To do this: 1 Click Start, Control Panel, Mobile PC, and then Power Options. The Windows® Power Options window appears. (Sample Image) Windows® Power Option window 2 Select an appropriate plan for your work environment or create your own custom plan. 3 Click Create a Power Plan to set up a new plan.
Mobile Computing Monitoring main battery power By default the three power plans Balanced, Power Saver, and High Performance are satisfactory for most people and do not need to be edited. The Power Saver plan is the best used for maximum battery time. The High Performance plan will give you the shortest battery time, but the highest performance from your computer. The Balanced plan is a compromise between battery time and performance.
Mobile Computing Changing the main battery 113 Changing the main battery When your main battery has run out of power, you have two options: plug in the AC adaptor or install a charged main battery. Never short circuit the battery pack by either accidentally or intentionally bringing the battery terminals in contact with another conductive object. This could cause serious injury or fire, and could also damage the battery pack and computer.
Mobile Computing Changing the main battery 5 Slide the battery release lock to the unlocked position. (Sample Illustration) Unlocking the battery release lock 6 Slide the battery release latch to release the battery. 7 Pull the discharged battery out of the computer.
Mobile Computing Changing the main battery 115 If the battery is leaking or its case is cracked, put on protective gloves to handle it, and discard it immediately. Always dispose of used battery packs in compliance with all applicable laws and regulations. Put insulating tape, such as cellophane tape, on the electrode during transportation to avoid a possible short circuit, fire or electric shock. Failure to do so could possibly result in serious injury.
Mobile Computing Taking care of your battery 3 Slide the battery release lock to the locked position. (Sample Illustration) Locking the battery release lock 4 Turn the computer right side up. 5 Reconnect any cables that were removed in step 3 of “Removing the battery from the computer” on page 113. 6 Restart the computer. Taking care of your battery The following sections offer tips on how to take care of your battery and prolong its life.
Mobile Computing Taking care of your battery 117 ❖ If a battery is leaking or damaged, replace it immediately. Use protective gloves when handling a damaged battery. ❖ To replace the main battery, use an identical battery that you can purchase through the Toshiba Web site at accessories.toshiba.com. ❖ A reverse polarity condition should be avoided with all batteries. The main battery is designed so that it cannot be installed in reverse polarity.
Mobile Computing Taking care of your battery ❖ If you have extra battery packs, rotate their use. ❖ If you will not be using the system for an extended period, more than one month, remove the battery pack. ❖ If you are not going to use the computer for more than eight hours, disconnect the AC adaptor. ❖ Store spare battery packs in a cool dry place out of direct sunlight. Disposing of used batteries The life of a battery pack depends on usage.
Mobile Computing Traveling tips 119 Toshiba is dedicated to preserving the environment by sponsoring Call2Recycle, a program of the Rechargeable Battery Recycling Corporation. For more information and for drop-off locations, visit www.rbrc.org or call 1-800-822-8837. Notice regarding CR coin cell batteries, applicable to California, U.S.A. only: Perchlorate Material - special handling may apply. See http://www.dtsc.ca.
Chapter 4 Exploring Your Computer’s Features In this chapter, you will explore some of the special features of your notebook computer. Exploring the desktop The desktop is the launching pad for everything you can do in the Windows® operating system. You use its features to start programs, find documents, set up system components, and perform most other computing tasks. HINT: The illustrated examples in this guide may appear slightly different from the screens displayed by your system.
Exploring Your Computer’s Features Exploring the desktop 121 Finding your way around the desktop Your computer’s desktop includes several standard features: icons, Start button, Taskbar, Notification Area, and background pattern. Icons Start button Notification Area Taskbar ® (Sample Image) Windows operating system desktop Icons An icon represents a folder, file, or program that can be quickly activated by double-clicking the icon.
Exploring Your Computer’s Features Exploring the desktop NOTE If you place the cursor over an icon, a popup description of the file contents appears. Your desktop may contain other icons depending on your configuration. See Windows® online Help for more specific information on each icon and how to use it.
Exploring Your Computer’s Features Setting up for communications 123 Setting up for communications To connect to the Internet, use an online service, or communicate across the telephone lines with another computer, you need: ❖ A modem (available on certain models) ❖ A telephone line ❖ A browser or communications program ❖ An Internet Service Provider (ISP) or online service if you plan to use the Internet Determining the COM port Your modem (available on certain models) is connected to one of the
Exploring Your Computer’s Features Setting up for communications 8 Click OK to close the Phone and Modem Options dialog box. 9 Close the Control Panel. Connecting a modem to a telephone line Your computer may come with a built-in modem (available on certain models) that can be connected to a standard voice-grade telephone line.
Exploring Your Computer’s Features Setting up for communications 2 125 Connect the other end to the RJ-11 wall jack. (Sample Illustration) Connecting to a wall jack NOTE Connect the built-in modem only to ordinary analog phone lines. Never connect the built-in modem to a digital line (ISDN). Never connect the built-in modem to the digital connector on a public telephone or to a digital private branch exchange (PBX). Never connect the built-in modem to a key telephone system for residences or offices.
Exploring Your Computer’s Features Setting up for communications Setting up the connection To set up an office connection, consult your network administrator for network settings and additional considerations. To set up a dial-up connection, use the Connect to the Internet Wizard: 1 Click Start, Control Panel, Network and Internet, and then Connect to the Internet. 2 Click Dial Up. 3 Enter the phone number and account information of your network connection.
Exploring Your Computer’s Features An overview of using the Internet 127 Using Wireless LAN connectivity NOTE Wireless connectivity and some features may require you to purchase additional software, external hardware or services. Availability of public wireless LAN access points may be limited. Your system may come with an optional wireless LAN module.
Exploring Your Computer’s Features An overview of using the Internet The Internet The Internet is an association of thousands of networks and millions of computers around the world connected by communications lines. They all work together to share information.
Exploring Your Computer’s Features An overview of using the Internet 129 If you are using your computer at the office, then you probably connect to the Internet through your company’s network. See your network administrator about connecting to the Internet. Surfing the Internet Once connected to the Internet, the Web browser displays a home page, for example, your ISP’s home page on the Internet or your company’s Web site home page. To visit a desired Web site, type in the Web address.
Exploring Your Computer’s Features Exploring audio features Uploading to, and downloading files from, the Internet Transferring files from one computer to another is termed uploading (transferring data from your computer to a site on the Web), or downloading (transferring data from a site on the Web to your computer). There are several ways to upload or download data.
Exploring Your Computer’s Features Exploring audio features NOTE 131 The microphone on your computer might be set to Mute. To check this, click Start, Control Panel, Hardware and Sound, and then Adjust System Volume. Using external speakers or headphones Your computer is equipped with a full stereo sound system with internal speakers. Instead of using the internal speakers, you can connect headphones or a pair of external stereo speakers.
Exploring Your Computer’s Features Using PC Cards Using PC Cards TECHNICAL NOTE: For PCMCIA-compatible PC Cards, check the package to make sure they conform to the PCMCIA 2.1 standard (or later). Other cards may work with your computer, but are likely to be much more difficult to set up and use.
Exploring Your Computer’s Features Using PC Cards 133 Removing a PC Card Be sure to disable the PC Card prior to removing it. Otherwise, the system may be damaged. NOTE 1 Before removing a PC Card, make sure that no applications or system services are using the card. Prepare the card for removal by clicking the Safely Remove Hardware icon in the Notification Area and then selecting the card or device you want to remove.
Exploring Your Computer’s Features Using the Bridge Media Adapter Slot Using the Bridge Media Adapter Slot (Available on certain models) The Bridge Media Adapter slot (available on certain models) supports the use of Memory Stick™, Memory Stick™ PRO, Secure Digital™ (SD™), MMC™ (MultiMediaCard™), or xD-Picture Card™ media. These media can be used with a variety of digital products: digital music players, cellular phones, PDAs, digital cameras, digital video camcorders, etc.
Exploring Your Computer’s Features Using the i.LINK® port 135 Removing memory media 1 Prepare the media for removal by clicking the Safely Remove Hardware icon in the Notification Area and then selecting the card or device you want to remove. If the system is unable to prepare the media for safe removal, a message will tell you to try again later. If the media can be removed now, the system displays Safe to Remove Hardware. 2 Gently press the card inward to release it. The card pops out slightly.
Chapter 5 Toshiba Utilities Your computer includes several utilities designed to help you to reconfigure your system to best meet your individual needs. Together, these allow you to ascertain certain system details, set additional options, or change default options. These utilities are described in this chapter.
Toshiba Utilities TOSHIBA Assist 137 TOSHIBA Assist The TOSHIBA Assist provides quick access to computer functions and allows you to customize a range of computer settings. To access TOSHIBA Assist, do one of the following: ❖ Double-click the TOSHIBA Assist shortcut icon on the desktop. ❖ Click Start, All Programs, Toshiba, Utilities, and then TOSHIBA Assist. The TOSHIBA Assist window appears.
Toshiba Utilities TOSHIBA Assist Connect The features available in this category are: ❖ ConfigFree™ Connectivity Doctor ❖ Bluetooth® Settings ❖ Bluetooth® Local COM Settings (Sample Image) TOSHIBA Assist window – Connect tab
Toshiba Utilities TOSHIBA Assist Secure The features available in this category are: ❖ Supervisor password ❖ User password (Sample Image) TOSHIBA Assist window – Secure tab 139
Toshiba Utilities TOSHIBA Assist Protect & Fix The TOSHIBA PC Diagnostic Tool Utility feature is available in this category.
Toshiba Utilities TOSHIBA Assist Optimize The features available in this category are: ❖ Mouse Utility ❖ TOSHIBA Accessibility ❖ TOSHIBA Button Controls ❖ Toshiba Hardware Setup ❖ CD/DVD Drive Acoustic Silencer (Sample Image) TOSHIBA Assist window – Optimize tab 141
Toshiba Utilities Setting passwords Setting passwords Setting a password lets you walk away from your computer, providing additional protection for your files. When you set a password, you must enter the password before you can work on your computer again. Toshiba supports several types of passwords on your computer: ❖ NOTE An instant password—Secures your open programs and files when leaving the computer temporarily.
Toshiba Utilities Setting passwords 143 Setting a supervisor password If you choose to set a supervisor or user password, Toshiba strongly recommends that you save your password in a location where you can later access it should you not remember it. Toshiba is not responsible for any losses that may occur to you, your organization or others as a result of the inability to access the computer. To set a supervisor password: 1 Click Start, All Programs, Toshiba, Utilities, and then TOSHIBA Assist.
Toshiba Utilities Setting passwords 4 Select Registered, then click OK. A pop-up screen appears asking for a password. 5 Enter your password, then enter it again to verify. 6 Click OK. A pop-up screen appears asking for the User Password Mode.
Toshiba Utilities Setting passwords 145 Setting a user password If you choose to set a supervisor or user password, Toshiba strongly recommends that you save your password in a location where you can later access it should you not remember it. Toshiba is not responsible for any losses that may occur to you, your organization or others as a result of the inability to access the computer.
Toshiba Utilities Setting passwords Deleting a user password To cancel the power-on password function: 1 Click Start, All Programs, Toshiba, Utilities, and then TOSHIBA Assist. The TOSHIBA Assist window appears. 2 On the left side, click the Secure tab. 3 Click the User Password icon. The Password tab of the Toshiba Hardware Setup window appears. 4 Click Not Registered. A pop-up screen appears asking for a password. 5 Enter the user password, then click OK.
Toshiba Utilities TOSHIBA PC Diagnostic Tool Utility 147 TOSHIBA PC Diagnostic Tool Utility This utility can help diagnose problems with devices in your computer. Refer to the online Help documentation within the application for additional help. NOTE The TOSHIBA PC Diagnostic Tool may show tests for features you do not have. This is normal and doesn’t indicate a problem.
Toshiba Utilities Mouse Utility Mouse Utility The Mouse utility allows you to change your pointing device or mouse settings. To access the Mouse utility: 1 Click Start, Control Panel, and then Mouse, or click the Mouse icon in the Optimize tab of TOSHIBA Assist. The Mouse Properties screen appears.
Toshiba Utilities Toshiba Hardware Setup 149 Toshiba Hardware Setup Toshiba Hardware Setup is the Toshiba configuration management tool available through the Windows® operating system. To access it: ❖ Click Start, All Programs, Toshiba, Utilities, and then Assist, or click the Toshiba Hardware Setup icon in the Optimize tab of TOSHIBA Assist. The Toshiba Hardware Setup screen appears.
Toshiba Utilities Toshiba Hardware Setup ❖ CPU—Allows you to enable or disable CPU frequency switching modes Dynamically Switchable—This mode is the default setting for your computer, and automatically changes the processing frequency and decreases voltage depending on the power source: ❖ AC Power—If your computer is connected to the AC adaptor, the CPU frequency mode is set to high for faster processing.
Toshiba Utilities TOSHIBA Zooming Utility 151 TOSHIBA Zooming Utility This utility allows you to select which applications will work with the zoom in/out hot keys (see “Hot Keys/TOSHIBA Cards” on page 199).
Toshiba Utilities CD/DVD Drive Acoustic Silencer For more information about how to use the TOSHIBA Zooming utility, right-click the icon in the Notification Area and then click Help. CD/DVD Drive Acoustic Silencer This utility can slow the speed of your optical drive to make it run more quietly. You can use this utility to make listening to music CDs more enjoyable. NOTE When you change the CD/DVD drive to “Quiet” mode, the setting is only valid for the current Windows® session.
Toshiba Utilities TOSHIBA Accessibility 153 TOSHIBA Accessibility The TOSHIBA Accessibility utility allows you to use the Fn key to create a hot key combination with one of the function keys without pressing the two keys simultaneously as is usually required. Using Accessibility lets you make the Fn key a sticky key, meaning you can press it once, release it, and then press a function key to activate the hot key function.
Toshiba Utilities Fingerprint Authentication Utility Fingerprint Authentication Utility (Available on certain models) The fingerprint authentication utility (available on certain models) can be used to replace the keyboard-based user/BIOS password authentication system when booting up. The fingerprint authentication utility can also be used for user logon. The user’s fingerprint is read; if the system recognizes the fingerprint, the user is automatically logged on.
Toshiba Utilities Fingerprint Authentication Utility 6 155 Swipe your finger on the reader. A sample will be created and indicated by a Fingerprint icon. 7 Repeat the previous step. Swipe the same finger on the reader two more times to create two more samples. 8 The final template will be created from these three samples. NOTE If you do not use a Windows® password, you will be prompted to define a new (non-empty) one. This is not necessary, but a password improves the security of your software.
Toshiba Utilities Fingerprint Authentication Utility Fingerprint Logon The fingerprint utility enables logon to your computer using fingerprints. During user enrollment, fingerprint samples are saved and associated with the user’s Windows® user account. When the user attempts to log on again, the user’s fingerprint is read and compared with the user’s enrolled fingerprints; if the fingerprint is recognized, user logon is completed.
Toshiba Utilities Fingerprint Authentication Utility NOTE 157 Your hardware must support Power-on security to use the single logon feature. You must have administrative privileges to change settings. To enable power-on security single logon: 1 Open the Control Center and go to Settings - System Settings. 2 Select Logon. 3 Check the Allow power-on security single sign-on check box. (Logon support must be enabled for this option to be accessible.
Toshiba Utilities Fingerprint Authentication Utility Fingerprints ❖ Enroll or Edit Fingerprints—Runs the fingerprint enrollment wizard. You can enroll/delete fingerprints for the current user and, if power-on security is implemented, control whether they are stored in the fingerprint device memory. After you enroll your fingerprints, they are associated with your user name and password. The next time you log in, you can use your fingerprints instead of your user name and password.
Toshiba Utilities Fingerprint Authentication Utility 159 Elevate Administrative Privileges for User ❖ Elevate administrative privileges for user.—By default, the operating system assumes you are a user and not an administrator, and renders most of the system settings in the Control Center gray and unavailable. To access these system settings, click “Elevate administrative privileges” on the main Fingerprint Control Center window.
Toshiba Utilities Fingerprint Authentication Utility Registering a new Web page or dialog You are logged on to the computer and want to register a new Web page. To create a new registration: 1 Display a Web page you want to register. 2 Fill in the data you want to replay the next time you access this Web page. 3 Use the reader to display the Biomenu. 4 Select Register. Password Bank recognizes pages containing a password field and displays a hint that the page can be registered.
Toshiba Utilities Fingerprint Authentication Utility ❖ 161 If the page has multiple registered forms, but there is no active form, all existing registered forms for the page are displayed. You then select the one to be replayed. Replaying a registered dialog You are logged on to the computer and want to replay a registered dialog. To replay a registration: 1 Display the dialog to be replayed. 2 Use the reader.
Toshiba Utilities Fingerprint Authentication Utility 3 Select Registrations. 4 Select a registration. 5 Click Delete. How to Delete the Fingerprint Data Fingerprint data is stored in the non-volatile memory. If the computer changes ownership, Toshiba recommends the following procedure: 1 Click Start, All Programs, Protector Suite QL, and then Control Center. The Protector Suite Software screen is displayed. 2 Click Fingerprints then Delete.
Toshiba Utilities Fingerprint Authentication Utility 163 ❖ Wash and dry your hands thoroughly. ❖ Remove static electricity from your fingers by touching any metal surface. Static electricity is a common cause of reader failures, especially during dry seasons such as winter. ❖ Clean the reader with a lint-free cloth. Do not use detergent to clean the reader.
Toshiba Utilities ConfigFree™ Fingerprint reader limitations ❖ The fingerprint reader compares and analyzes the unique characteristics in a fingerprint. However, there may be instances where certain users are unable to register their fingerprints due to insufficient unique characteristics in their fingerprints. ❖ A warning message will be displayed when recognition is abnormal or recognition is not successful within a fixed duration. ❖ The recognition success rate may differ from user to user.
Toshiba Utilities ConfigFree™ 165 Getting Started This section contains information about the ConfigFree main screen, and how to start and set up ConfigFree. For more detailed information on setting up and using ConfigFree, see the Help File included in the application. Starting ConfigFree To start ConfigFree, be sure the computer has a wired or wireless connection. Then perform any of the following steps: ❖ Click Start, All Programs, Toshiba, Networking, and then ConfigFree.
Toshiba Utilities ConfigFree™ ❖ Status of Wireless Connection switch (Sample Image) Connectivity Doctor screen Profile Settings The Profile Settings utility lets you save network settings in “profiles.” ConfigFree profiles are useful for easily switching network settings and devices.You can switch network settings simply by selecting the profile with the desired settings.
Toshiba Utilities ConfigFree™ To create a profile: 1 Click the 2 Move the pointer to Profile. 3 Click Open Settings. icon in the Notification area. The ConfigFree Profile Settings window appears. (Sample Image) ConfigFree Profile Settings window 4 Click Add to start the Create Profile Wizard.
Chapter 6 If Something Goes Wrong Some problems you may encounter when using your computer are relatively easy to identify and solve. Others may require help from your network administrator or the manufacturer of the software program. This chapter aims to help you solve many problems by yourself. It covers the problems you are most likely to encounter. If all else fails, contact Toshiba. You will find information on Toshiba’s support services at the end of this chapter.
If Something Goes Wrong Problems when you turn on the computer 2 169 Click the Applications tab. If a program has stopped responding, the words “not responding” appear beside its name in the list. 3 Select the program you want to close, then click End Task. Closing the failed program should allow you to continue working. If it does not, continue with the next step. 4 Close the remaining programs one by one by selecting the program name, then End Task.
If Something Goes Wrong Problems when you turn on the computer If you are using an AC adaptor, verify that the computer is receiving power from the external power source by looking at the AC power light. If the indicator is glowing, the computer is connected to a live external power source. The computer starts but when you press a key nothing happens. Verify that the active program accepts text input. Try clicking your mouse on an area where you can type text and try typing again.
If Something Goes Wrong Problems when you turn on the computer 171 If you are running on battery power, it is recommended that you do not leave the computer in Sleep mode for long periods of time. To charge the battery, leave the computer plugged into a live wall outlet for several hours. For more information see “Charging batteries” on page 104. The computer displays the Non-System disk or disk error message. Make sure there is no diskette in the optional external diskette drive.
If Something Goes Wrong The Windows® operating system is not working 5 Verify that the AC adaptor is the correct unit for your computer model. The computer may not be able to start from an AC adaptor that is rated for less current (amperage) than the computer requires, even if the rated voltage is correct, and the plug fits correctly in the DC-IN socket. The labels on the bottom of the computer and the AC adaptor show the specifications for voltage ("V") and current ("A") for each device.
If Something Goes Wrong The Windows® operating system is not working ❖ Safe Mode with Command Prompt ❖ Enable Boot Logging ❖ Enable low-resolution video (640x480) ❖ Last Known Good Configuration (advanced) ❖ Directory Services Restore Mode ❖ Debugging Mode ❖ Disable automatic restart on system failure ❖ Disable Driver Signature Enforcement ❖ Start Windows® normally 173 When you highlight each option using the arrow keys, Windows® displays information about each option at the bottom after
If Something Goes Wrong Resolving a hardware conflict The Windows® operating system can help you If the operating system has started properly but you still have a problem using your computer, the online Help can assist you in troubleshooting the problem. To access the Windows® operating system Help and Support: 1 Click Start, then click Help and Support, or press F1. The Help and Support window appears.
If Something Goes Wrong Resolving a hardware conflict 175 The device most recently connected to the system is the one most likely to be causing a conflict. Resolving conflicts There are several things you can do to resolve hardware conflicts: ❖ Get the most recent drivers from the manufacturer. ❖ Disable the device. For an older device, remove it from the computer. ❖ Disable another system component and use its resources for the new device. See “Fixing a problem with Device Manager” on page 175.
If Something Goes Wrong Resolving a hardware conflict ❖ The Resources tab, which lists resources assigned to the monitor, optical drive, optional external diskette drive, and other power-using functions. This tab does not appear if the device is not using resources. ❖ The Driver tab, which displays the drivers being used by the device. This tab also provides options for updating the driver or rolling back the driver in case the new version is causing a problem.
If Something Goes Wrong Resolving a hardware conflict 177 Power and the batteries Your computer receives its power through the AC adaptor and power cord/cable or from the system batteries (battery, optional secondary battery, and real-time clock (RTC) battery). Power problems are interrelated. For example, a faulty AC adaptor or power cord/cable will neither power the computer nor recharge the batteries.
If Something Goes Wrong Resolving a hardware conflict Check the power options via your Power Plans (see “Power Plans” on page 111 for more information). Have you added a device, such as a PC Card or memory module, that takes its power from the battery? Is your software using the hard disk more? Is the display power set to turn off automatically? Was the battery fully charged to begin with? All these conditions affect how long the charge lasts.
If Something Goes Wrong Resolving a hardware conflict 179 Display problems Here are some typical display problems and their solutions: The screen is blank. Display Auto Off may have gone into effect. Press any key to activate the screen. You may have activated the instant password feature by pressing Fn and F1 simultaneously. If you have registered a password, press any key, type the password and press Enter. If no password is registered, press any key.
If Something Goes Wrong Resolving a hardware conflict The built-in screen flickers. Some flickering is a normal result of the way the screen produces colors. To reduce the amount of flickering, try using fewer colors. To change the number of colors displayed: 1 Right-click in a blank area of the Windows® desktop. 2 Click Personalize, and then Display Settings. 3 Change the Colors option and click OK. For more information see Windows® Help.
If Something Goes Wrong Resolving a hardware conflict 181 Disk drive problems Problems with the hard disk or with a diskette drive usually show up as an inability to access the disk or as sector errors. Sometimes a disk problem may cause one or more files to appear to have garbage in them. Typical disk problems are: You are having trouble accessing a disk, or one or more files appear to be missing. Make sure you are identifying the drive by its correct name (A: or C:).
If Something Goes Wrong Resolving a hardware conflict Your data files are damaged or corrupted. Refer to your software documentation for file recovery procedures. Many software packages automatically create backup files. You may also be able to recover lost data using utility software. Consult your network administrator. Some programs run correctly but others do not. This is probably a configuration problem.
If Something Goes Wrong Resolving a hardware conflict 183 You press the disc eject button, but the drive tray does not slide out. Make sure the computer is connected to a power source and turned on. The optical drive eject mechanism requires power to operate. Make sure a program is not accessing the drive and preventing it from ejecting.
If Something Goes Wrong Resolving a hardware conflict The computer emits a loud, high-pitched noise. This is feedback between the microphone and the speakers. It occurs in any sound system when input from a microphone is fed to the speakers and the speaker volume is too loud. Adjust the volume control. PC Card problems PC Cards (PCMCIA-compatible) include many types of devices, such as a removable hard disk, additional memory, or a pager.
If Something Goes Wrong Resolving a hardware conflict 3 185 Double-click the appropriate PC Card. The operating system displays your PC Card’s Properties dialog box, which contains information about your PC Card configuration and status. The computer stops working (hangs) when you insert a PC Card. The problem may be caused by an I/O (input/output) conflict between the PCMCIA socket and another device in the system. Use Device Manager to make sure each device has its own I/O base address.
If Something Goes Wrong Resolving a hardware conflict Printer problems This section lists some of the most common printer problems. The printer will not print. Check that the printer is connected to a working power outlet, turned on and ready (on line). Check that the printer has plenty of paper. Some printers will not start printing when there are just two or three sheets of paper left in the tray. Make sure the printer cable is firmly attached to the computer and the printer.
If Something Goes Wrong Resolving a hardware conflict 187 Wireless networking problems This section provides general troubleshooting tips for networking problems, specifically wireless (Wi-Fi®) networking. NOTE The terms and concepts used assume a basic understanding of networks, and may be for more advanced users. If you need assistance or if you are not familiar with the terminology, please see Windows® Help and Support or contact your computer technician.
If Something Goes Wrong Resolving a hardware conflict ❖ 4 Verify that the DHCP Enabled setting is set to Yes. 5 Click Close. Use IPCONFIG to verify that the computer has a useful IP address—one other than the private address of 169.254.xxx.xxx assigned by Windows®. 1 Click Start to open the Start menu. 2 Type Cmd in the search field. 3 At the top-left of the Start menu, click cmd.exe to open the command prompt. 4 Enter IPCONFIG /ALL and press Enter.
If Something Goes Wrong DVD operating problems 189 Special considerations for the Windows® operating system Wired Equivalent Privacy (WEP) encryption is not enabled on the wireless access point. When you install a wireless access point device, the Windows® operating system checks whether WEP encryption is enabled on the device.
If Something Goes Wrong Develop good computing habits 4 Verify that your computer recognizes your optical drive by clicking Start, and then Computer. The optical drive should appear in the list. 5 See “Checking device properties” on page 175 for instructions on using Device Manager to view the optical drive properties. 6 Check the Toshiba Web site for new information on optical drives and their operation. A blank screen appears while watching a DVD-ROM movie or title.
If Something Goes Wrong Develop good computing habits 191 On a regular basis, back up the information stored on your hard disk. Use Windows® to back up files, or the entire computer, to a CD, DVD, or external hard disk. Here are some ways you can do this: ❖ Use the Windows® operating system to back up files or your entire computer to a CD, DVD, or external hard disk. ❖ Copy files to diskette. ❖ Copy files to a rewritable external storage device.
If Something Goes Wrong Develop good computing habits Saving system configuration with Restore Points The System Restore feature of the Windows® operating system quickly creates Restore Points—‘snapshots’ of your Windows® operating system configuration—and saves them for later recall.
If Something Goes Wrong Develop good computing habits NOTE 4 193 This list may contain Restore Points that you did not create. Restore Points labeled System Checkpoint were automatically created by the Windows® operating system. Other Restore Points may have been created automatically by applications when they were installed. Select the Restore Point you want to use, and then click Next. The utility displays the timestamp and description of the selected Restore Point.
If Something Goes Wrong Develop good computing habits 1 Prepare your backup target by connecting it and/or inserting a blank CD or DVD in the drive. 2 Click Start. 3 Click Control Panel. 4 Click System and Maintenance. 5 Click Backup and Restore Center. 6 You can choose to back up some files or the entire computer. Click either Back up files or Back up computer.
If Something Goes Wrong If you need further assistance 195 successfully. Always carefully follow the installation instructions that accompany the hardware or software. ❖ Restart the Windows® operating system. Always restart the Windows® operating system after each installation, even if the installation utility does not prompt you to do so. This will ensure that the installation is completed, and will clean up anything that the installation utility left behind. ❖ Do one installation at a time.
If Something Goes Wrong If you need further assistance Contact the software company’s technical support group for their assistance. ❖ Consult the dealer from whom you purchased your computer and/or program. Your dealer is your best source for current information. For the complete detailed specifications for your computer, visit pcsupport.toshiba.com. Go to the Tech Support Center, select your particular model from the list and go to the Detailed Specifications for that model.
If Something Goes Wrong Other Toshiba Internet Web sites 197 Other Toshiba Internet Web sites toshiba.com Worldwide Toshiba corporate site computers.toshiba.com Marketing and product information in the USA accessories.toshiba.com Accessories information in the USA www.toshiba.ca Canada www.toshiba-Europe.com Europe www.toshiba.co.jp/index.htm Japan http://servicio.toshiba.com Mexico and all of Latin America Toshiba’s worldwide offices Australia Toshiba (Australia) Pty.
If Something Goes Wrong Toshiba’s worldwide offices Spain Toshiba Information Systems (España) S.A. Parque Empresarial San Fernando Edificio Europa, 1a Planta Escalera A 28831 (Madrid) San Fernando de Henares Spain United Kingdom Toshiba Information Systems (U.K) Ltd. Toshiba Court Weybridge Business Park Addlestone Road Weybridge, Surrey KT15 2UL United Kingdom United States Toshiba America Information Systems, Inc.
Appendix A Hot Keys/TOSHIBA Cards Hot Keys and TOSHIBA Cards provide a quick way to modify selected system functions and to launch applications. There are two types of TOSHIBA Cards: Hot Key Cards and Application Cards. Hot Key Cards The Hot Key Cards are used to modify the following system functions: ❖ Mute ❖ Instant security ❖ Power Plan ❖ Sleep ❖ Hibernation ❖ Display switch ❖ Brightness control ❖ Wireless communication switch ❖ TouchPad switch ❖ Display resolution switch 199 5.
Hot Keys/TOSHIBA Cards Hot Key Cards Using the Hot Key Cards The Hot Key Cards are normally hidden from view. The Cards appear only when the pointing device is moved to the top center edge of the screen. In addition, a Hot Key Card can be displayed by pressing the associated hot key. NOTE Hot keys are keys that, when pressed in combination with the Fn key, turn system functions on and off. Hot keys have a legend on the key indicating the option or feature the key controls.
Hot Keys/TOSHIBA Cards Application Cards 201 Application Cards The Application Cards are used to launch these applications: PC Diagnostic Tool utility For more information, refer to “TOSHIBA PC Diagnostic Tool Utility” on page 147. Toshiba Hardware Setup utility For more information, refer to “Toshiba Hardware Setup” on page 149. Using the Application Cards To launch an application using the Application Cards: 1 Move the cursor to the top center edge of the screen.
Hot Keys/TOSHIBA Cards Application Cards Card Case The Card Case feature allows you to choose which cards appear in the Application Card display (see “Using the Application Cards” on page 201). To use the Card Case: 1 Move the cursor to the top center edge of the screen. The TOSHIBA Cards appear at the top of the screen. An icon appears momentarily in the top-right corner. 2 Click the icon.
Hot Keys/TOSHIBA Cards Hot Key Functions 203 Hot Key Functions Hot key functions are performed using either the Hot Key Cards or by pressing the associated hot key. This section lists the available Hot Key Functions. NOTE Hot keys are keys that, when pressed in combination with the Fn key, turn system functions on and off. Hot keys have a legend on the key indicating the option or feature the key controls. Volume Mute This TOSHIBA Card or hot key enables/disables volume mute on your computer.
Hot Keys/TOSHIBA Cards Hot Key Functions Password security This TOSHIBA Card or hot key blanks the display. Selecting this Card or pressing the hot key displays the following options: or Fn + (Sample Image) Security options ❖ To enable security, select ❖ To cancel, select . . Without a password The Fn + F1 hot key function turns off the display and activates instant security.
Hot Keys/TOSHIBA Cards Hot Key Functions 205 To activate the password feature: 1 Click Start, Control Panel, and then Appearances and Personalization. 2 Click one of the following: ❖ Choose a screen saver in the “Pick a task” section ❖ Display in the “or pick a Control Panel icon” section The Display Properties window appears. 3 If you clicked Choose a screen saver, the Screen Saver tab has already been selected. If it is not selected, click the Screen Saver tab.
Hot Keys/TOSHIBA Cards Hot Key Functions Power plan This TOSHIBA Card or hot key displays the power plans and cycles through the power plans. or Fn + The properties of each power plan, and the power plans that are displayed by this function, are set in the Power Options window. Selecting this Card or pressing the hot key displays the currently selectable power plans: (Sample Image) Power Plan options Cycle through the power plans, then select the desired power plan. 5.375 x 8.375 ver 2.
Hot Keys/TOSHIBA Cards Hot Key Functions 207 Sleep mode This TOSHIBA Card or hot key places the computer into Sleep mode. For more information about Sleep mode, please see “Using and configuring Sleep mode” on page 79. or Fn + Selecting this Card or pressing the hot key displays the following options: (Sample Image) Sleep options ❖ To enable sleep mode, select ❖ To cancel, select 5.375 x 8.375 ver 2.3 . .
Hot Keys/TOSHIBA Cards Hot Key Functions Hibernation mode This TOSHIBA Card or hot key places the computer into Hibernation mode. or Fn + If Hibernation mode is disabled, this hot key will not respond. For more information on Hibernation mode, see “Using and configuring Hibernation mode” on page 77. Selecting this Card or pressing the hot key displays the following options: (Sample Image) Hibernation options ❖ To enable Hibernation mode, select ❖ To cancel, select 5.375 x 8.375 ver 2.3 . .
Hot Keys/TOSHIBA Cards Hot Key Functions 209 Display modes This TOSHIBA Card or hot key cycles through the poweron display options. The display modes are: or ❖ Built-in display only ❖ Built-in display and external monitor simultaneously ❖ External monitor only ❖ Built-in display and TV ❖ TV only Fn + To use a simultaneous mode, you must set the resolution of the internal display panel to match the resolution of the external display device.
Hot Keys/TOSHIBA Cards Hot Key Functions Display brightness This TOSHIBA Card decreases or increases the screen brightness. Fn + This hot key decreases the screen brightness. Fn + This hot key increases the screen brightness. Selecting this Card or pressing either hot key displays the following options: (Sample Image) Display brightness Move the slider or press the appropriate hot key repeatedly to decrease or increase the display brightness. 5.375 x 8.375 ver 2.
Hot Keys/TOSHIBA Cards Hot Key Functions 211 Disabling or enabling wireless devices This TOSHIBA Card or hot key enables/disables the optional wireless devices installed in your computer. The wireless modes are: or ❖ Wi-Fi® enabled—Enables just the Wi-Fi® module. ❖ Bluetooth® enabled—Enables just the Bluetooth® module. ❖ All disabled—Disables both the Bluetooth® and Wi-Fi® modules. ❖ All enabled—Enables both Bluetooth® and Wi-Fi.
Hot Keys/TOSHIBA Cards Hot Key Functions Disabling or enabling the TouchPad™ or Dual Mode Pad (The Dual Mode Pad is available on certain models). This TOSHIBA Card or hot key enables/disables either the TouchPad or the Dual Mode Pad. or Fn + For more information on using the Touch Pad or Dual Mode Pad, see “Using the TouchPad™” on page 64 or “Using the Dual Mode Pad” on page 66.
Hot Keys/TOSHIBA Cards Hot Key Functions 213 Zooming applications in/out Fn + This hot key turns the Zooming utility to zoom-out. Fn + This hot key turns the Zooming utility to zoom-in. For more information, see “TOSHIBA Zooming Utility” on page 151. Keyboard hot key functions Fn + This hot key turns the cursor control overlay on and off. Fn + This hot key turns the numeric overlay on and off. Fn + This hot key turns the scroll lock feature on and off.
Appendix B Power Cord/Cable Connectors Your notebook computer features a universal power supply you can use worldwide. This appendix shows the shapes of the typical AC power cord/cable connectors for various parts of the world. USA and Canada United Kingdom UL approved CSA approved BS approved Australia Europe AS approved VDA approved NEMKO approved 214 5.375 x 8.375 ver 2.
Glossary TECHNICAL NOTE: Some features defined in this glossary may not be available on your computer. Acronyms The following acronyms may appear in this user’s guide.
Glossary DOS disk operating system DPI dots per inch DSTN dual supertwist nematic DVD digital versatile (or video) disc DVD-ROM digital versatile (or video) disc read-only memory ECP enhanced capabilities port EPROM erasable programmable read-only memory FAT file allocation table FCC Federal Communications Commission GB gigabyte HDD hard disk drive HTML Hypertext Markup Language IEEE Institute of Electrical and Electronics Engineers I/O input/output IRQ interrupt request IS
Glossary SDRAM synchronous dynamic random access memory SRAM static random access memory SVGA super video graphics adapter TFT thin film transistor USB universal serial bus URL uniform resource locator WAN wide area network www World Wide Web 217 Terms The following terms may appear in this user’s guide. A active-matrix display — A liquid crystal display (LCD) made from an array of liquid crystal cells using active-matrix technology.
Glossary baud rate — The speed at which a communication device, such as a printer or modem, transmits information. Baud rate is the number of signal changes per second (not necessarily the same as bits per second). See also bits per second. BIOS (basic input/output system) — Basic instructions, stored in readonly memory (ROM), containing the information the computer needs to check hardware and load the operating system when you start up the computer.
Glossary 219 central processing unit (CPU) — The chip that functions as the “brain” of the computer. It takes information from outside sources, such as memory or keyboard input, processes the information, and sends the results to another device that uses the information. character — Any letter, number, or symbol you can use on the computer. Some characters are non-printing characters, such as a paragraph break in a word-processing program. A character occupies one byte of computer storage.
Glossary device — A component attached to the computer. Devices may be external (outside the computer’s case) or internal (inside the computer’s case). Printers, disk drives, and modems are examples of devices. device driver — A program (called a “driver”) that permits a computer to communicate with a device. dialog box — An on-screen window displayed by the operating system or a program giving a direction or requesting input from the user.
Glossary 221 double-density diskette — A 3.5-inch diskette that can hold up to 720 KB of information (half the capacity of a high-density diskette). See also diskette, high-density diskette. download — (1) In communications, to receive a file from another computer through a modem or network. (2) To send font data from the computer to a printer. See also upload. drag — To hold down the mouse button while moving the cursor to drag a selected object.
Glossary file extension — The three characters following the period (pronounced “dot”) at the end of a file name. The extension indicates the type of file. Examples are .exe for program files and .hlp for help files. See also file name. folder — Also called directory. A container for organizing files saved to a disk. A folder is symbolized on screen by a graphical image (icon) of a file folder. A folder can contain files and other folders.
Glossary 223 hot key — (1) A feature in which certain keys in combination with the Fn key can set system options or control system parameters, such as the battery save mode. (2) A key or combination of keys that activates a memory resident program. hot swapping — The ability to add or remove devices from a computer while the computer is running and have the operating system automatically recognize the change. I icon — A small image displayed on the screen that represents a function, file, or program.
Glossary local area network — See LAN. logical drive — A section of a disk that is recognized by the operating system as a separate disk drive. A system’s logical drives may differ from its physical drives. For example, a single hard disk drive may be partitioned into two or more logical drives. M memory — Typically refers to the computer’s main memory, where programs are run and data is temporarily stored and processed.
Glossary 225 non-system disk — A disk for storing programs and data that cannot be used to start the computer. Compare system disk. O online — Available through the computer. Online may refer to information being read from your own computer’s hard disk, such as online documentation or online Help, or to information coming from another company on a company network or the Internet. operating system — A set of programs that controls how the computer works.
Glossary port — A socket on the computer where you plug in a cable for connection to a network or a peripheral device. processor — See central processing unit (CPU). program — A set of instructions that can be executed by a computer. The general classes of programs (also called software) are operating system, application, and utility. See also operating system, application, utility. properties — The attributes of an object or device.
Glossary S 227 select — To highlight or otherwise specify text, data, or graphics with the intent to perform some operation on it. serial — Processes that occur one at a time. In communications, it means the transmission of one bit at a time sequentially over a single channel. On your computer, the serial port provides a serial interface between the computer and an appropriate device. Compare parallel. shortcut — See keyboard shortcut.
W Glossary Web — See World Wide Web. Wi-Fi — A registered trademark term of the Wi-Fi Alliance that stands for Wireless Fidelity, and is another term for the communication protocol to permit an Ethernet connection using wireless communication components. World Wide Web (www) — The worldwide network of Web sites linked together over the Internet. A user of the Web can jump from site to site regardless of the location of the computer hosting the site. See also Internet.
Index A AC adaptor 42 AC power connecting adaptor 43 accessories memory 47 adding memory 47 adjusting recording quality 131 Alt keys 87 audio files 130 audio features 130 B backing up files 84 battery changing 113 charge indicator light 44, 106 charge not lasting 177 charging 42, 44 conserving power 110 disposal 118 low charge 108 monitoring power 44, 106 not charging 177 229 notification 109 power plan 206 power plan hot key card 112 real-time clock (RTC) 103 removing 113 BIOS Setup see Toshiba Hardware
Index set up 123 compact disc positioning 98 compact discs handling 98 inserting 97 removing 100, 101 compact disk drive using 95 computer caring for 82 cleaning 82 moving 82 non-system disk or disk error message 171 not accessing disk drives 170 running on battery power 102 setting up 40, 48 warning resume failure message 170 computer lock 83 computing tips 84 connecting to a power source 42 connection set up 126 control buttons 65 Ctrl keys 87 missing files/trouble accessing a disk 181 running slow
Index monitor not working 180 mouse 70 external diskette drive connecting 72 external display, adjusting 69 F FAT (File Allocation Table) 181 file extensions 93 file, backing up 84 files backing up 94 printing 93 restoring 94 saving 91 fingerprint authentication 154 enrollment 154 Fn keys 87 function keys 87 H hardware conflicts 174 resolving 175 headphones using 131 Help and Support Windows® 174 Hibernation mode 73 configuring 77 starting again from 79 hot key display brightness 210 display modes 209 Hi
Index using 85 Windows special keys 87 keyboard, external 70 keyboard, full-size 86 L lock computer, using 83 M main battery removing 113 memory adding 47 problem solving 176 removing expansion slot cover 50 memory module inserting 51 installation 48 removing 55 microphone 130 modem connecting to telephone line 124 determining COM port 123 resetting port to default settings 123 upgrading 123 monitor 68 connecting 68 not working 179 mouse installing 70 serial 70 mouse utility 148 N network accessing
Index power plan hot key card 112 power plans 110 power source 42 connecting 43 powering down using Hibernation 77 using Sleep 75, 79 precautions 38 primary button 65 printer connecting 70 problem solving 186 printing a file 93 problem solving AC power 177 accessing disk drives 170 battery charge does not last 177 battery not charging 177 cannot insert diskette in drive 182 cannot read a diskette 182 changing display properties 180 checking device properties 175 computer hangs when PC Card inserted 185 com
Index computer 119 disposing of batteries 118 icons 35 precautions 38 saving files 91 screen blank 179 does not look normal/flickers 179 secondary button 65 set up communications 123 setting up adding memory 47 computer 40, 48 setting up a connection 126 Sleep mode 74 hot key 207 starting again from 82 sound problem solving 183 sounds recording 130 speakers using external 131 start button 122 Start Search field 91 starting a program 89 Start Search field 91 Windows Explorer 90 Windows Start menu 89 st
Index Help and Support 174 wireless networking 127 Wizards Dial-Up Networking Wizard 125 World Wide Web 128 www 128 235