Satellite A200/Satellite Pro A200 TOSHIBA Satellite A200/ Satellite Pro A200 Series User's Manual
Copyright © 2007 by TOSHIBA Corporation. All rights reserved. Under copyright law, this manual cannot be reproduced in any form without the prior written permission of TOSHIBA. No patent liability is assumed, with respect to the use of the information contained herein. TOSHIBA Satellite A200/Satellite Pro A200 Series Portable Personal Computer User's Manual First edition March 2007 Ownership and copyright of music, video computer programs, databases, etc. are protected by the copyright laws.
iLINK is a trademark of Sony Corporation. Other trademarks and registered trademarks not listed above may be used in this manual. Macrovision License of Notice This product incorporates copyright protection technology that is protected by U.S. patents and other intellectual property rights. Use of this copyright protection technology must be authorized by Macrovision, and is intended for home and other limited viewing uses only unless otherwise authorized by Macrovision.
■ Before you connect the computer to a power source, ensure that the voltage rating of the AC adapter matches that of the available power source. 115V/60Hz in most of North and South America and some Far Eastern countries such as Taiwan. 100 V/50Hz in eastern Japan and 100 V/60Hz in western Japan. 230 V/50 Hz in most of Europe, the Middle East, and the Far East.
When using telephone equipment in conjunction with your computer, basic safety precautions should always be followed to reduce the risk of fire, electric shock and injury to persons, including the following: ■ Do not use this product near water, for example, near a bathtub, washing bowl, kitchen sink or laundry tub, in a wet basement or near a swimming pool. ■ Avoid using a telephone (other than a cordless type) during an electrical storm. There may be a remote risk of electric shock from lightning.
Only peripherals complying with the FCC class B limits may be attached to this equipment. Operation with non-compliant peripherals or peripherals not recommended by TOSHIBA is likely to result in interference to radio and TV reception. Shielded cables must be used between the external devices and the computer's or expansion unit's external monitor port, parallel port, USB port and microphone jack.
Canadian Regulatory Information (Canada Only) This digital apparatus does not exceed the Class B limits for radio noise emissions from digital apparatus as set out in the Radio Interference Regulation of the Canadian Department of Communications. Note that Canadian Department of Communications (DOC) regulations provide, that changes or modifications not expressly approved by TOSHIBA Corporation could void your authority to operate this equipment.
Optical Disc Drive Safety Instruction ■ Be sure to check the international precautions at the end of this section. The optical drive that is used in this computer is equipped with a laser device. A classification label with the following sentence is affixed to the surface of the drive.
TOSHIBA Samsung Storage Technology CD-RW/DVD-ROM TS-L462D ■ The CD-RW/DVD-ROM drive employs a laser system. To ensure proper use of this product, please read this instruction manual carefully and retain for future reference. Should the unit ever require maintenance, contact an authorized service location. ■ Use of controls, adjustments or the performance of procedures other than those specified may result in hazardous radiation exposure.
TEAC CD-RW/DVD-ROM DW-224E ■ The CD-RW/DVD-ROM drive employs a laser system. To ensure proper use of this product, please read this instruction manual carefully and retain for future reference. Should the unit ever require maintenance, contact an authorized service location. ■ Use of controls, adjustments or the performance of procedures other than those specified may result in hazardous radiation exposure. ■ To prevent direct exposure to the laser beam, do not try to open the enclosure.
Pioneer DVD Super Multi DVR-K17 ■ The DVD Super Multi drive employs a laser system. To ensure proper use of this product, please read this instruction manual carefully and retain for future reference. Should the unit ever require maintenance, contact an authorized service location. ■ Use of controls, adjustments or the performance of procedures other than those specified may result in hazardous radiation exposure. ■ To prevent direct exposure to the laser beam, do not try to open the enclosure.
TOSHIBA Samsung Storage Technology DVD-Super Multi TS-L632 ■ The DVD-Super Multi drive employs a laser system. To ensure proper use of this product, please read this instruction manual carefully and retain for future reference. Should the unit ever require maintenance, contact an authorized service location. ■ Use of controls, adjustments or the performance of procedures other than those specified may result in hazardous radiation exposure.
Hitachi-LG Data Storage DVD Super Multi GSA-T20N ■ The DVD Super Multi drive employs a laser system. To ensure proper use of this product, please read this instruction manual carefully and retain for future reference. Should the unit ever require maintenance, contact an authorized service location. ■ Use of controls, adjustments or the performance of procedures other than those specified may result in hazardous radiation exposure.
Panasonic DVD Super Multi UJ-850U ■ The DVD Super Multi drive employs a laser system. To ensure proper use of this product, please read this instruction manual carefully and retain for future reference. Should the unit ever require maintenance, contact an authorized service location. ■ Use of controls, adjustments or the performance of procedures other than those specified may result in hazardous radiation exposure. ■ To prevent direct exposure to the laser beam, do not try to open the enclosure.
TEAC DVD-Super Multi DV-W28EC ■ The DVD-Super Multi drive employs a laser system. To ensure proper use of this product, please read this instruction manual carefully and retain for future reference. Should the unit ever require maintenance, contact an authorized service location. ■ Use of controls, adjustments or the performance of procedures other than those specified may result in hazardous radiation exposure. ■ To prevent direct exposure to the laser beam, do not try to open the enclosure.
International Precautions CAUTION: This appliance contains a laser system and is classified as a "CLASS 1 LASER PRODUCT." To use this model properly, read the instruction manual carefully and keep this manual for your future reference. In case of any trouble with this model, please contact your nearest "AUTHORIZED service station." To prevent direct exposure to the laser beam, do not try to open the enclosure.
VORSICHT: DIE VERWENDUNG VON ANDEREN STEURUNGEN ODER EINSTELLUNGEN ODER DAS DURCHFÜHREN VON ANDEREN VORGÄNGEN ALS IN DER BEDIENUNGSANLEITUNG BESCHRIEBEN KÖNNEN GEFÄHRLICHE STRAHLENEXPOSITIONEN ZUR FOLGE HABEN. Modem warning notice Conformity Statement The equipment has been approved to [Commission Decision "CTR21"] for pan- European single terminal connection to the Public Switched Telephone Network (PSTN).
Japan regulations Region selection If you are using the computer in Japan, technical regulations described in the Telecommunications Business Law require that you select the Japan country mode. It is illegal to use the modem in Japan with any other selection. Redial Up to two redial attempts can be made. If more than two redial attempts are made, the modem will return Black Listed. If you are experiencing problems with the Black Listed code, set the interval between redials at one minute or longer.
Telephone company procedures The goal of the telephone company is to provide you with the best service it can. In order to do this, it may occasionally be necessary for them to make changes in their equipment, operations, or procedures. If these changes might affect your service or the operation of your equipment, the telephone company will give you notice in writing to allow you to make any changes necessary to maintain uninterrupted service.
Instructions for IC CS-03 certified equipment 1. NOTICE: The Industry Canada label identifies certified equipment. This certification means that the equipment meets certain telecommunications network protective, operational and safety requirements as prescribed in the appropriate Terminal Equipment Technical Requirements document(s). The Department does not guarantee the equipment will operate to the user's satisfaction.
Notes for Users in Australia and New Zealand Modem warning notice for Australia Modems connected to the Australian telecoms network must have a valid Austel permit. This modem has been specifically configured to ensure compliance with Austel standards when the country/region selection is set to Australia. The use of other country/region setting while the modem is attached to the Australian PSTN would result in your modem being operated in a noncompliant manner.
Notes for use of this device in New Zealand ■ The grant of a Telepermit for a device in no way indicates Telecom acceptance of responsibility for the correct operation of that device under all operating conditions. In particular the higher speeds at which this modem is capable of operating depend on a specific network implementation which is only one of many ways of delivering high quality voice telephony to customers. Failure to operate should not be reported as a fault to Telecom.
■ ■ ■ ■ ■ (b) caller identification information (which occurs between the first and second ring cadences) is not destroyed. The preferred method of dialling is to use DTMF tones (ATDT...) as this is faster and more reliable than pulse (decadic) dialling. If for some reason you must use decadic dealing, your communications program must be set up to record numbers using the following translation table as this modem does not implement the New Zealand "Reverse Dialling" standard.
Important Notice Copyrighted works including, but not limited to music, video, computer program, databases are protected by copyright laws. Unless specifically permitted under applicable copyright laws, you cannot copy, modify, assign, transmit or otherwise dispose of any copyrighted work with the consent of the owner of the copyright. Please take notice that unauthorized copying, modification, assignment, transmission and disposition may be subject to claims for damages and penalties.
Heat injury ■ Avoid prolonged physical contact with the computer. If the computer is used for long periods, its surface can become very warm. While the temperature will not feel hot to the touch, if you maintain physical contact with the computer for a long time, for example if you rest the computer on your lap or if you keep your hands on the palm rest, your skin might suffer a low-heat injury.
xxvi Satellite A200/Satellite Pro A200
Satellite A200/Satellite Pro A200 Table of Contents Preface Manual contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . xxxii Conventions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .xxxiii Equipment checklist . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . xxxiv Chapter 1 Satellite A200/Satellite Pro A200 Series Features Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Chapter 3 Getting Started Connecting the AC adapter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-2 Opening the display . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-3 Turning on the power. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-3 Starting up for the first time . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-4 Turning off the power. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-4 Restarting the computer .
Chapter 5 The Keyboard Typewriter keys . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-1 F1 ... F12 function keys . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-2 Soft keys: Fn key combinations. . . . . . . . . . . . . . . . . . . . . . . . . . 5-2 Hotkeys . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-3 Windows special keys . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-4 Keypad overlay . . . .
Chapter 10 Disclaimers CPU . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10-1 Memory (Main System) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10-2 Battery Life. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10-2 HDD Drive Capacity . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10-3 LCD . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Satellite A200/Satellite Pro A200 Series Preface Congratulations on your purchase of the Satellite A200/Satellite Pro A200 Series computer. This powerful notebook computer provides excellent expansion capability, including multimedia devices, and it is designed to provide years of reliable, high-performance computing. This manual tells how to set up and begin using your Satellite A200/Satellite Pro A200 Series computer.
Preface Manual contents This manual has ten chapters, three appendixes and a glossary. Chapter 1, Satellite A200/Satellite Pro A200 Series Features, is an overview of the computer's special features, utilities, and options. Chapter 2, The Grand Tour, identifies the components of the computer and briefly explains how they function. Chapter 3, Getting Started, provides a quick overview of how to begin operating your computer and gives tips on safety and designing your work area.
Preface Conventions This manual uses the following formats to describe, identify, and highlight terms and operating procedures. Abbreviations On first appearance, and whenever necessary for clarity, abbreviations are enclosed in parentheses following their definition. For example: Read Only Memory (ROM). Acronyms are also defined in the Glossary. Icons Icons identify ports, dials, and other parts of your computer.
Preface Messages Messages are used in this manual to bring important information to your attention. Each type of message is identified as shown below. Pay attention! A caution informs you that improper use of equipment or failure to follow instructions may cause data loss or damage your equipment. Please read. A note is a hint or advice that helps you make best use of your equipment.
Preface Software Microsoft® Windows Vista™ Home Basic/Home Premium/Business Edition ■ The following software which is pre-installed on your hard disk: ■ Microsoft® Windows Vista™ Home Basic/Home Premium/Business Edition ■ DVD Video Player ■ TOSHIBA Disc Creator ■ TOSHIBA Direct Disc Writer ■ TOSHIBA ConfigFree ■ TOSHIBA Assist ■ TOSHIBA SD Memory Card Format* ■ TOSHIBA Acoustic Silencer ■ TOSHIBA HW Setup ■ TOSHIBA Value Add Package Utility ■ TOSHIBA Supervisor Password Utility ■ Ulead DVD MovieFactory® ■
Preface xxxvi Satellite A200/Satellite Pro A200 Series
Satellite A200/Satellite Pro A200 Chapter 1 Satellite A200/Satellite Pro A200 Series Features This chapter identifies the computer's special features, options and accessories. Basic features are described in a separate pamphlet. Some of the features described in this manual may not function properly if you use an operating system that was not pre-installed by TOSHIBA.
Satellite A200/Satellite Pro A200 Series Features Chipset Mobile Intel® 945PM/GM/943GML Express Chipset Realtek High Definition Audio Codec ALC861D TI CardReader & 1394a Controller PCI8402 Realtek 10M/100M/1Gbps LAN Controller RTL8111B, 10M/100M LAN Controller RTL8101E Memory The graphics system in your computer may use part of the main system memory for graphics performance and therefore reduce the amount of system memory available for other computing activities.
Satellite A200/Satellite Pro A200 Series Features Power Battery Pack 3-cell Lithium Ion smart battery pack with 10.8V*2000mAh* 6-cell Lithium Ion smart battery pack with 10.8V*4000mAh 9-cell Lithium Ion smart battery pack with 10.8V*6000mAh Approximately 12 hours or longer charging time to 100% battery capacity with system switched on. Approximately 4 hours charge time to 100% battery capacity with system switched off. Approximately 1.
Satellite A200/Satellite Pro A200 Series Features TouchPad/Dual Mode Pad A TouchPad/Dual Mode Pad and control buttons in the palm rest enable control of the on-screen pointer. The Dual Mode Pad is a TouchPad that provides normal touchpad features in its default mode and switches to a DualMode interface when the upper right corner of the TouchPad is tapped. Tapping the same corner again will revert to normal pointing mode.
Satellite A200/Satellite Pro A200 Series Features Disclaimer (HDD Drive Capacity) For more information on the Disclaimer regarding HDD Drive Capacity, please refer to the Disclaimers section in Chapter 10. CD-RW/DVD-ROM drive Satellite A200/Satellite Pro A200 Some models are equipped with a full-size CDRW/DVD-ROM module that lets you record data to rewritable CD/CD-RWs as well as run either 12cm (4.72") or 8cm (3.15") CD/DVDs without using an adapter.
Satellite A200/Satellite Pro A200 Series Features DVD Super Multi drive supporting ± R Double Layer Some models are equipped with a full-size DVD Super Multi drive supporting ±R Double Layer module with dual layer support that lets you record data to rewritable CD/DVDs as well as run either 12cm (4.72") or 8cm (3.15") CD/DVDs without using an adapter. It reads DVD-ROMs at maximum 8x speed and CD-ROMs at maximum 24x speed.
Satellite A200/Satellite Pro A200 Series Features Ports (depending on configuration) External monitor 15-pin analog VGA port supports VESA DDC2B compatible functions. Universal Serial Bus The computer has four Universal Serial Bus (USB) ports that comply with the USB 2.0 standard, which enables data transfer speeds more than 40 times faster than USB 1.1 (which this computer also supports). i.
Satellite A200/Satellite Pro A200 Series Features Wireless LAN The computer has a built-in wireless LAN minicard that is compatible with other LAN systems that support the following: 802.11a/b/g/n wireless LAN module/ 802.11a/b/g wireless LAN module/ 802.11b/g wireless LAN module. It has a Frequency Channel Selection (2.4 or 5 GHz) and allows roaming over multiple channels.
Satellite A200/Satellite Pro A200 Series Features System Automatic Sleep/Hibernation This feature automatically places the system into either Sleep Mode or Hibernation Mode when there is no input or hardware access for a specified time period. You can specify the time period and select either System Sleep or System Hibernate in the Power Options. Keypad Overlay A ten-key pad is integrated into the keyboard.
Satellite A200/Satellite Pro A200 Series Features ■ Before entering Sleep mode, be sure to save your data. ■ Do not install or remove a memory module while the computer is in Sleep mode. The computer or the module could be damaged. ■ Do not remove the battery pack while the computer is in Sleep mode. Data in memory will be lost. TOSHIBA Value Added Package This section describes the TOSHIBA Component features pre-installed on the computer.
Satellite A200/Satellite Pro A200 Series Features Utilities and Applications This section describes preinstalled utilities and tells how to start them. For details on operations, refer to each utility’s online manual, help files or readme.txt files. TOSHIBA Assist TOSHIBA Assist is a graphical user interface that provides easy access to help and services. DVD Video Player The DVD player is used to play DVD Video media through an on-screen interface and functions.
Satellite A200/Satellite Pro A200 Series Features Ulead DVD MovieFactory® for TOSHIBA You can edit digital video and make a DVD-Video and support Label Flash function. The availability of Label Flash function depends on the model you purchased. Windows Mobility Center Mobility Center is a utility for accessing several mobile PC settings quickly in one window. A default maximum of eight tiles are provided by the operating system, and the additional two titles are added to your Mobility Center.
Satellite A200/Satellite Pro A200 Chapter 2 The Grand Tour This chapter identifies the various components of your computer. Become familiar with each component before you operate the computer. Certain types of notebook chassis are designed to accommodate all possible configurations for an entire product series. Your selected model may not have all the features and specifications corresponding to all of the icons or switches shown on the notebook chassis, unless you have selected all those features.
The Grand Tour 2-2 Front Edge Logo* Front Edge Logo indicates the computer series you bought. (The availability of this function depends on the model you purchased.) DC IN LED The DC IN LED indicates the computer is connected to the AC adapter and it is plugged into an AC power source. Power LED In normal operating mode, the Power LED is blue (depending on the model you purchased).
The Grand Tour Microphone Jack The standard 3.5 mm mini microphone jack enables connection of a three conductive type mini-jack for a monaural microphone. Headphone Jack The headphone jack lets you connect stereo headphones or other audio-output devices such as external speakers. Connecting headphones or other devices to this jack automatically disables the internal speakers. Volume Control Use this dial to adjust the volume of the stereo speakers or headphones.
The Grand Tour Optical Disc Drive The computer is configured with a full-size optical disc drive module that lets you run either 12 cm (4.72") or 8 cm (3.15") discs without using an adapter. See the Drives section in this chapter for technical specifications on each drive and Chapter 4, Operating Basics, for information on using the drive and caring for discs. Optical Disc Drive LED This indicator lets you know when the Optical Disc Drive is being accessed. Eject Button Opens the Optical Disc Drive.
The Grand Tour To prevent possible over heating of the CPU, never block the fan vent. TV Out Port* Connect a 4-pin S- video cable into this connector in order to output either an NTSC or PAL television signal. (The availability of this function depends on the model you purchased.) LAN Jack This jack lets you connect to a LAN. The adapter has built-in support for Ethernet LAN (10 Mbps, 10BASE-T), Fast Ethernet LAN (100 Mbps, 100BASE-TX) and Gigabit Ethernet LAN (1000 Mbps, 1000BASE-T).
The Grand Tour Underside The following figure shows the underside of the computer. Make sure the display is closed before turning over your computer. 2 3 1 7 4 6 5 1. 2. 3. 4. EXPANSION MEMORY SOCKET HDD1 HDD2* FAN VENT 5. 6. 7. BATTERY PACK LATCH BATTERY PACK BATTERY PACK LOCK * The availability of this feature is dependent on the model you purchased. The bottom of the computer Expansion Memory Socket Use this socket to install a memory module to increase your computer's memory.
The Grand Tour Battery Pack Latch With the Battery Pack Lock in its unlocked position, you can slide this latch in order to remove the battery pack. Battery Pack The battery pack powers the computer when the AC adapter is not connected. For detailed information on the battery pack, refer to Chapter 6, Power and Power-Up Modes. Battery Pack Lock When you slide this into its locked position, the battery pack cannot be released even if you attempt to slide the battery pack latch into its open position.
The Grand Tour Display Screen The LCD displays high-contrast text and graphics at a resolution up to 1280X800 pixels. Refer to Appendix B - Display Modes for further information. When the computer operates from the AC adapter, the display screen's image will be somewhat brighter than when it operates on battery power - this is normal and is designed to conserve battery power. To prolong the life of your display screen, use a screen saver when you're not using the computer and it is idle.
The Grand Tour Play/Pause Button* Press this button to begin playing an audio CD, a DVD movie or digital audio files. This button also acts as a Pause button. (The availability of this function depends on the model you purchased.) Stop* Stops playing the CD, DVD or digital audio. (The availability of this function depends on the model you purchased.) Previous Button* Skips backwards to the previous track, chapter or digital file. Refer to Chapter 4, Operating Basics, for details.
The Grand Tour Arrow Mode When the Arrow mode icon lights blue, you can use the keypad overlay (light gray labelled keys) as cursor keys. Refer to the Keypad overlay section in Chapter 5, The Keyboard. Numeric Mode You can use the keypad overlay (light gray labelled keys) for numeric input when the Numeric mode icon lights blue. Refer to the Keypad overlay section in Chapter 5, The Keyboard. Caps Lock The Caps Lock LED lights when you press the Caps Lock key.
The Grand Tour CDs ■ CD-R discs can be written only once. The recorded data cannot be erased or changed. ■ CD-RW discs can be recorded more than once. Use either 1x, 2x, or 4x multi-speed CD-RW discs or high-speed 4x to 10x discs. The write speed of ultra-speed CD-RW discs is a maximum of 24x speed. DVDs ■ DVD-R and DVD+R discs can be written only once. The recorded data cannot be erased or changed. ■ DVD-RW, DVD+RW and DVD-RAM discs can be recorded more than once.
The Grand Tour This drive cannot use discs that allow writing faster than 8x speed or faster (DVD-R and DVD+R with Single Layer), 6x speed or faster (DVD-RW), 8x speed or faster (DVD+RW), 5x speed (DVD-RAM) or ultra-speed or faster (CD-RW). AC adapter The AC adapter converts AC power to DC power and reduces the voltage supplied to the computer.
Satellite A200/Satellite Pro A200 Chapter 3 Getting Started This chapter provides basic information to get you started using your computer. It covers the following topics: Be sure also to read Instruction Manual for Safety & Comfort. This guide, which is included with the computer, explains product liability.
Getting Started Connecting the AC adapter Attach the AC adapter when you need to charge the battery or you want to operate from AC power. It is also the fastest way to get started, because the battery pack will need to be charged before you can operate from battery power. The AC adapter can be connected to any power source supplying from 100 to 240 volts and 50 or 60 hertz. For details on using the AC adapter to charge the battery pack, refer to Chapter 6, Power and Power-Up Modes.
Getting Started Opening the display The display panel can be rotated in a wide range of angles for optimal viewing. 1. Push the display latch on the front of the computer. Opening the display 2. Lift the panel up and adjust it to the best viewing angle for you. Use reasonable care when opening and closing the display panel. Opening it vigorously or slamming it shut could damage the computer. Turning on the power This section describes how to turn on the power.
Getting Started Starting up for the first time When you first turn on the power, the computer's initial screen is the Windows Vista™ Startup Screen Logo. Follow the on-screen directions for each screen. During setup, you can click the Back button to return to the previous screen. Be sure to read the Windows Operating System End User License Agreement carefully. Turning off the power The power can be turned off in one of three modes, either Shutdown (Boot) Mode, Hibernation Mode or Sleep Mode.
Getting Started Sleep Mode If you do have to interrupt your work, you are able to turn off the power without exiting from your software by placing the computer into Sleep Mode. In this mode data is maintained in the computer’s main memory so that, when you turn on the power again, you can continue working right where you left off. ■ When the AC adaptor is connected, the computer will go into Sleep Mode according to the settings in the Power Options.
Getting Started Executing Sleep Mode You can enter also Sleep Mode by pressing Fn + F3 - please refer to Chapter 5, The Keyboard, for further details. Youu can enter Sleep Mode in one of three ways: 1. Click Start then click the sleep button ( ) located in the power management buttons ( ), or click the arrow button ( ) and select Sleep from the menu. 2. Close the computer’s LCD display panel.
Getting Started Benefits of Hibernation Mode The Hibernation Mode feature provides the following benefits: ■ Saves Data to the hard disk drive when the computer automatically shutsdown because of a low battery condition. ■ You can return to your previous working environment immediately when you turn on the computer. ■ Saves power by shutting down the system when the computer receives no input or hardware access for the time period set by the System Hibernate feature.
Getting Started Restarting the computer Certain conditions require that you reset the computer, for example if: ■ You change certain computer settings. ■ An errors and the computer does not respond you your keyboard commands. If you need to restart the computer, there are three ways this can be achieved: 1. Click Start then click the arrow button ( ) in the power management buttons ( ) and select Restart from the menu. 2.
Getting Started Restoring the preinstalled software from the Product Recovery disc If preinstalled files are damaged, use the Product Recovery disc to restore them. To restore the operating system and all preinstalled software, follow the steps below. When you reinstall the Windows operating system, the hard disk will be reformatted and all data will be lost. You can not use System Recovery Options if restoring the pre-installed software without System Recovery options. 1.
Getting Started Create an Optical Recovery Discs ■ Be sure to connect the AC adaptor when you create Recovery Discs. ■ Be sure to close all other software programs except the Recovery Disc Creator. ■ Do not run software such as screen savers which can put a heavy load on the CPU. ■ Operate the computer at full power. ■ Do not use power-saving features. ■ Do not write to the disc when the virus check software is running.
Getting Started Restoring the pre-installed software from the Recovery Hard Disk Drive A portion of the total hard disk drive space is configured as a hidden recovery partition. This partition stores files which can be used to restore pre-installed software in the event of a problem. If you subsequently set up your hard disk drive again, do not change, delete or add partitions in a manner other than specified in the manual, otherwise you may find that space for the required software is not available.
Getting Started When removing pre-installed drivers / utilities or when installing, you can setup the respective drivers / utilities from the following folder. C: \TOSAPINS\*** When Installing TOSHIBA SD Memory Card Format or other SD utilities, select TOSHIBA SD Memory Utilities from C:\TOSAPINS\.
Satellite A200/Satellite Pro A200 Chapter 4 Operating Basics This chapter gives information on basic operations including using the TouchPad/Dual Mode Pad, optical disc drives, the internal modem, LAN and wireless LAN. It also provides tips on caring for your computer and on heat dispersal. Using the TouchPad/Dual Mode Pad To use the TouchPad/Dual Mode Pad, simply move your finger tip across it in the direction you want the on-screen pointer to go. 2 1 1. TOUCHPAD CONTROL BUTTONS 2.
Operating Basics Do not press on the TouchPad/Dual Mode Pad too hard or press a sharp object such as a ball point pen against it. The TouchPad/Dual Mode Pad could be damaged. The TouchPad/Dual Mode Pad has similar functions to a two-button mouse with a scroll wheel. For some functions, you can tap it instead of pressing a button. You can customize pointing device actions in Mouse Properties. Open the Control Panel, select the Mouse icon and press Enter to open the Mouse Properties window.
Operating Basics 1 2 Mail button Starts your mail box for you to receive and send mails. ConfigFree ConfigFree is a suite of utilities to allow easy control of communication devices and network connections. It also allows you to find communication problems and create profiles for easy switching between locations and communication networks. Windows Vista Photo Gallery Windows Vista Photo Gallery gives you many tools for your digital photos and videos.
Operating Basics Using the Web Camera This section describes the bundled Web Camera utility, which can capture still and video images. The Web Camera will auto-run when Windows starts.
Operating Basics Using the software The Web Camera software is pre-configured to start when you turn on Windows Vista; if you need to restart it go to Start Programs Camera Assistant Software Camera Assistant Software. 1 2 3 4 5 6 8 1. 2. 3. 4. 7 CAPTURE STILL IMAGES VIDEO RECORDING AUDIO RECORDING FUNCTION 5. 6. 7. 8. DISPLAY WINDOW CAMERA RESOLUTION MUTE EFFECTS Capture Still Images Click to see a preview of the captured image; you can also e-mail the image.
Operating Basics Settings Choose from the: Options tab to change the tool position; the Picture tab to select picture output options such as size, export file and saving location; the Video tab to choose output settings such as Frame Rate, Size, Compression and the file save path; the Audio tab to chnage the Audio Device, Compression, Volume and file save path. Help Displays the help files for the software.
Operating Basics Region selection Telecommunication regulations vary from one country/region to another, so you will need to make sure the internal modem's settings are correct for the country/region in which it will be used. 1. Open the Modem Region Select application. It is located on the Programs menu at TOSHIBA > Networking. Do not use the Country/Region Select function in the Modem setup utility in the Control Panel if the function is available.
Operating Basics Settings You can enable or disable the following settings: AutoRun Mode Region Select Utility starts automatically when you start up the operating system. Open the Dialing Properties dialog box after selecting region. The dialing properties dialog box will be displayed automatically after you select the region. Location list for region selection. A submenu appears displaying location information for telephony.
Operating Basics Connecting the internal modem Do not pull on the cable or move the computer while the cable is connected. If you find that the modem speed is low or communication is interrupted when you are using the modem, please set the CPU speed to Maximum within the Power Options. Disconnecting To disconnect the internal modem cable, follow the steps below. 1. Pinch the lever on the connector in the telephone jack and pull out the connector. 2.
Operating Basics To connect the LAN cable, follow the steps below. 1. Turn off the power to the computer and to all external devices connected to the computer. 2. Plug one end of the cable into the LAN jack. Press gently until you hear the latch click into place. Connecting the LAN cable 3. Plug the other end of the cable into a LAN hub connector. Check with your LAN administrator before connecting to a hub. Disconnecting the LAN cable To disconnect the LAN cable, follow the steps below. 1.
Operating Basics 11a, 11b, 11g and 11n wireless are based on IEEE 802.11a, 802.11b, 802.11g and 802.11n respectively. The IEEE 802.11n specification has not been finalized and is currently in draft release. The TOSHIBA 11a/b/g/n Wireless LAN Adapters are based on the Draft Release, Version 1.0, of the IEEE 802.11n specification. An Adapter with 11a/b, 11a/b/g or 11a/b/g/n can communicate on any of its supported formats; the actual connection will be based on the access point to which it connects.
Operating Basics Security Two advanced security mechanisms ensure a high level of security: ■ Authentication prevents access to critical data and makes it impossible to falsify the origin of a message. ■ Encryption prevents eavesdropping and maintains link privacy.
Operating Basics Wireless communication LED The LED indicates the status of the wireless communication functions. LED status Indication LED off Wireless communication switch is set to off. LED glows Wireless communication switch is on. Using optical disc drives The illustrations in this section might differ slightly from your drive, but operation is the same for all optical disc drives. The full-size drive provides high-performance execution of disc-based programs. You can run either 12 cm (4.
Operating Basics b. Pressing the eject button will not open the drawer when the computer's power is off. If the power is off, you can open the drawer by inserting a slender object (about 15 mm) such as a straightened paper clip into the eject hole just to the right of the eject button. Manual release with the eject hole 3. Grasp the drawer gently and pull until it is fully open.
Operating Basics 4. Lay the disc, label side up, in the drawer. Inserting a disc 5. Press gently at the center of the disc until you feel it click into place. The disc should lie below the top of the spindle, flush with its base. 6. Push the center of the drawer to close it. Press gently until it locks in place.
Operating Basics Removing compact discs To remove the disc, follow the steps below. Do not press the eject button while the computer is accessing the disc drive. Wait for the optical disc indicator to go out before you open the drawer. Also, if the disc is spinning when you open it, wait for it to stop before you remove it. 1. To pop the drawer partially open, press the eject button. Gently pull the drawer out until it is fully opened.
Operating Basics TOSHIBA Button Support CD/DVD play control buttons In addition to the power button, the following four buttons control functions relating to the playback of optical media and digital audio data: Satellite A200/Satellite Pro A200 4-17
Operating Basics Given the technological limitations of current optical disc writing drives, you may experience unexpected writing or rewriting errors due to disc quality or problems with hardware devices. Also, it is a good idea to make two or more copies of important data, in case of undesired change or loss of the recorded contents. CD-R discs can be written only once. CD-RW discs can be rewritten many times.
Operating Basics When writing or rewriting Please observe/consider the following when you write or rewrite to a CD-R/ RW. ■ Do not perform any of the following actions when writing or rewriting: ■ Change users in the Windows Vista™ operating system. ■ Operate the computer for any other function, including using a mouse or TouchPad/Dual Mode Pad or closing/opening the LCD panel. ■ Start a communication application such as a modem. ■ Apply impact or vibration to the computer.
Operating Basics Disclaimer TOSHIBA does not bear responsibility for the following: ■ Damage to any CD-R/RW or DVD-R/-RW/+R/+RW/-RAM disc that may be caused by writing or rewriting with this product. ■ Any change or loss of the recorded contents of CD-R/RW or DVD-R/RW/ +R/+RW /-RAM media that may be caused by writing or rewriting with this product, or for any business profit loss or business interruption that may be caused by the change or loss of the recorded contents.
Operating Basics *DVD-RAM DVD Specifications for DVD-RAM Disc for Version 2.0, Version 2.1 or Version 2.2 Matsushita Electric Industrial Co., Ltd. Hitachi Maxell Ltd. *DVD Multi drive and DVD Super Multi can use DVDRAM. DVD+R (Double Layer) MITSUBISHI CHEMICAL CORPORATION DVD-R (Dual Layer) MITSUBISHI CHEMICAL COPRORATION DVD-R Label Flash FUJIFILM Corporation DVD+R Label Flash FUJIFILM Corporation ■ If the disc is poor in quality, dirty or damaged, writing or rewriting errors may occur.
Operating Basics ■ Two types of DVD-R/+R/-RW/+RW/-RAM discs are on the market: data and video. Use a video disc to store video data. You can use video discs on a DVD recorder as well as on your computer's DVD-ROM drive. You cannot use data discs on a DVD recorder. ■ DVD-RAM formatted by FAT32 cannot be read in Windows 2000 without DVD-RAM Driver Software. ■ When multiple drives that can write data to discs are connected, be careful not to write to the wrong drive.
Operating Basics ■ Set the computer on a level surface and avoid places subject to vibration such as airplanes, trains or cars. Do not use an unstable surface such as a stand. ■ Keep mobile phones and other wireless communication devices away from the computer. ■ Always copy data from the hard disk drive to the CD. Do not use cutand-paste as the original data will be lost if there is a write error. How to make a Label Flash DVD Simplified steps for making a Label Flash DVD: 1.
Operating Basics Simplified steps for making a DVD-Video from adding a video source: 1. Click Start All Programs DVD MovieFactory for TOSHIBA Ulead DVD MovieFactory for TOSHIBA Launcher to launch DVD MovieFactory. 2. Click Video Disc New Project to invoke 2nd Launcher, choose your project type, then invoke DVD MovieFactory. 3. Add source from HD Disk by click Add Video files button to invoke browser dialog box. 4. Choose the sourse video then go to the Next page to apply Menu. 5.
Operating Basics 2. Before recording the video to DVD ■ When you record to DVD disc, please use only discs recommended by the Drive manufacturer. ■ Do not set the working drive to a slow device like a USB 1.1 hard disk drive or it will fail to write DVD. ■ Do not perform any of the following actions: - - Operate the computer for any other function, including using a mouse or TouchPad/Dual Mode Pad or closing/opening the LCD panel. Bump or cause vibration to the computer.
Operating Basics ■ Do not use the "Disc Backup" function of TOSHIBA Disc Ceator to copy DVD-Video and DVD-ROM with copyright protection.DVD-RAM media cannot be backed up with the “Disc Backup” finction of TOSHIBA Disc Ceator ■ You cannot back up a CD-ROM or CD-R/RW to DVD-R/-RW or DVD+R/ +RW using the Disc Backup function of TOSHIBA Disc Ceator ■ You cannot back up DVD-ROM, DVD-Video or DVD-R/-RW or DVD+R/ +RW to CD-R/RW using TOSHIBA Disc Ceator ■ TOSHIBA Disc Ceator cannot record in packet format.
Operating Basics Media Care This section provides tips on protecting data stored on your discs and disks. Handle your media with care. The following simple precautions will increase the lifetime of your media and protect the data stored on it: 1. Store your discs in the container they came in to protect them and keep them clean. 2. Do not bend the disc. 3. Do not write on, apply a sticker to, or otherwise mar the surface of the disc that contains data. 4.
Operating Basics TV-Out Use the TV-Out port to connect to a television. Be sure to use a 4 pin type S-video cable. For more details, see Appendix B. TV OUT PORT Setting up more than one display You can set up your computer to utilize more than one display, effectively spreading a single desktop screen across two monitors. The Display Properties window allows you to adjust more precisely the relative positioning of the two displays when they are configured as an extended desktop.
Operating Basics If an external display will not be connected next time you use your computer, you should cancel any extended desktop or clone display settings before shutting down your computer. Clone display settings are those where more than one device has been selected and is simultaneously applicable. Cleaning the computer To help ensure long, trouble-free operation, keep the computer free of dust and use care with liquids around the computer. ■ Be careful not to spill liquids into the computer.
Operating Basics 4-30 Satellite A200/Satellite Pro A200
Satellite A200/Satellite Pro A200 Chapter 5 The Keyboard The computer's keyboard layouts are compatible with a 104/105-key enhanced keyboard. By pressing some keys in combination, all the 104/ 105-key keyboard functions can be executed on the computer. The number of keys on your keyboard depends on which country/region's keyboard layout your computer is configured with. Keyboards for numerous languages are available.
The Keyboard F1 ... F12 function keys The function keys, not to be confused with Fn, are the 12 keys at the top of your keyboard. These keys are dark gray, but function differently from the other dark gray keys. F1 through F12 are called function keys because they execute programmed functions when pressed. Used in combination with the Fn key, keys marked with icons execute specific functions on the computer. See the section, Soft keys: Fn key combinations, in this chapter.
The Keyboard Press Fn + Ctrl to simulate the enhanced keyboard's right Ctrl key. Hotkeys Fn + ESC Mute Turns the volume on and off. Fn + F1 Lock Enters "Lock computer" mode. To restore your desktop, you need to log on again. Fn + F2 Power Plan Mode Displays the power save modes and lets you change the power settings Fn + F3 Sleep This hot key switches the system to Sleep mode. Fn + F4 Hibernate This hot key switches the system to Hibernate mode. Fn + F5 Output Changes displays.
The Keyboard Fn + 1 Fn + 2 Zoom Out To reduce the icon size on the desktop or the application window, press the 1 key while holding down the Fn key. Zoom In To enlarge the icon size on the desktop or the application window, press the 2 key while holding down the Fn key. Windows special keys The keyboard provides two keys that have special functions in Windows Vista™. One activates the Start menu and the other has the same function as the secondary mouse button.
The Keyboard The numeric keypad overlay (U.S.) Temporarily using normal keyboard (overlay on) While using the overlay, you can temporarily access the normal keyboard without turning off the overlay: 1. Hold down Fn and press any other key. All keys will operate as if the overlay were off. 2. Type upper-case characters by holding down Fn + Shift and pressing a character key. 3. Release Fn to continue using the overlay.
The Keyboard Temporarily changing modes If the computer is in Numeric mode, you can switch temporarily to Arrow mode by pressing a shift key. If the computer is in Arrow mode, you can switch temporarily to Numeric mode by pressing a shift key. Generating ASCII characters Not all ASCII characters can be generated using normal keyboard operation. But, you can generate these characters using their ASCII codes. With the overlay on: 1. Hold down Alt. 2. Using the overlay keys, type the ASCII code. 3.
Satellite A200/Satellite Pro A200 Chapter 6 Power and Power-Up Modes The computer's power resources include the AC adapter and internal batteries. This chapter gives details on making the most effective use of these resources including charging and changing batteries, tips for saving battery power, and power up modes.
Power and Power-Up Modes Power on AC adapter not connected Power off (no operation) Battery capacity is above low battery trigger point • Operates • LED: Battery off DC IN off Battery capacity is below low battery trigger point • Operates • Alarm sounds (this function depends on how the computer is configured) • LED: Battery flashes amber DC IN off Battery capacity exhausted Computer goes into Hibernation or shuts down (depending on the TOSHIBA Power Saver setting) No battery installed • No operat
Power and Power-Up Modes Power indicators As shown in the above table, the Battery, DC IN and Power indicators alert you to the computer's operating capability and battery charge status Battery indicator Check the Battery indicator to determine the status of the battery. The following indicator lights indicate the battery status. Flashing Amber The battery charge is low. The AC adapter must be connected to recharge the battery Amber Indicates the AC adapter is connected and is charging the battery.
Power and Power-Up Modes Battery types The computer has two types of batteries: ■ Battery pack ■ Real Time Clock (RTC) battery Battery pack When the AC adapter is not connected, the computer's main power source is a removable lithium ion battery pack, also referred to in this manual as the battery. You can purchase additional battery packs for extended use of the computer away from an AC power source. The battery is a disposable item.
Power and Power-Up Modes When this error appears, the following action is recommended. 1. Connect the AC adapter and let the battery charge for 24-hours. 2. Press F2 to enter BIOS setup menu. 3. Set correct time and date. If you still see the error message after performing the above actions, please contact your TOSHIBA service representative. Care and use of the battery pack The battery pack is a vital component of portable computing.
Power and Power-Up Modes 6. Use only the battery pack supplied with the computer or other device or an battery pack approved by the computer or device's manufacturer. Battery packs have different voltages and terminal polarities. Use of an improper battery could cause smoke, fire or rupture of the battery pack. 7. Never subject a battery pack to heat, such as storage near a heat source. Exposure to heat can cause the battery pack to ignite, explode or leak caustic liquid and cause death or serious injury.
Power and Power-Up Modes 5. Charge the battery pack only in an ambient temperature between 5 and 30 degrees Celsius. Otherwise, the electrolyte solution might leak, battery pack performance might deteriorate and the battery life might be shortened. 6. Be sure to monitor the remaining battery power. If the battery pack or real time clock battery discharge completely, Sleep Mode will not function, and data in memory will be lost, and the computer might register an incorrect time and date.
Power and Power-Up Modes Time The following table shows the time required to fully charge a discharged battery. Charging time (hours) Battery type Power on Power off Battery pack about 12 or longer about 4 or longer RTC battery about 24 about 24 with AC or Battery pack The charging time when the computer is on is affected by ambient temperature, the temperature of the computer and how you use the computer.
Power and Power-Up Modes Leaving the AC adapter connected will shorten battery life. At least once a week, run the computer on battery power until the battery is fully discharged, then recharge the battery. Monitoring battery capacity Remaining battery power can be monitored using the following methods.
Power and Power-Up Modes Retaining data with power off (Sleep mode) When you turn off your computer with fully charged batteries, the batteries retain data/charge for the following approximate time periods: Battery Approximately 1.5 days (Sleep mode, 9-cell) Approximately 1 day (Sleep mode, 6-cell) Approximately 0.
Power and Power-Up Modes 5. Unlock the Battery Pack Lock. 1 2 Removing the battery pack-1 6. Slide the battery pack latch to the left, then pull the battery out of the battery bay.
Power and Power-Up Modes Installing the battery pack To install a battery pack, follow the steps below. The battery pack is a lithium ion battery, which can explode if not properly replaced, used, handled or disposed of. Dispose of the battery as required by local ordinances or regulations. Use only batteries recommended by TOSHIBA as replacements. 1. Turn the computer's power off. 2. Disconnect all cables connected to the computer. 3.
Power and Power-Up Modes TOSHIBA Password Utility The TOSHIBA Supervisor Password Utility provides two levels of password security: User and Supervisor. Passwords set in TOSHIBA Supervisor Password Utility are different from the Windows® login password. User Password To start the utility, point to or click the following items: Launch TOSHIBA Assist SECURE User Password ■ Registered Click to register a password of up to 8 characters.
Power and Power-Up Modes 2. Enter the Password. 3. Press Enter. If you enter the password incorrectly three consecutive times, the computer shuts down. You must turn on the computer again and re-enter the password.
Satellite A200/Satellite Pro A200 Chapter 7 HW Setup This chapter explains how to use the TOSHIBA HW Setup utility to configure your computer. TOSHIBA HW Setup lets you configure settings for various hardware devices through a number of tabs titled General, Password, Display, Boot Priority, Keyboard, CPU, LAN, and USB.
HW Setup General This window displays the BIOS version and contains two buttons: Default Return all HW Setup values to the factory settings. About Display the HW Setup version. Setup This field displays BIOS Version and date. When finish BIOS update , please restart your computer and press F2 into BIOS setup manual and load BIOS default one time. Password This tab allows you to set or reset the user password for power on.
HW Setup Boot Priority Boot Priority Options This option sets the priority for booting the computer. Select the boot priority from the drop down list. You can override the settings and manually select a boot device by pressing one of the following keys while the computer is booting: U Selects the USB floppy disk drive. N Selects the Network. C Selects optical device. To select the boot drive you want, follow the steps below. 1. Boot-up your computer and press F12 to enter the boot menu. 2.
HW Setup LAN Wake-up on LAN This feature lets the computer's power be turned on when it receives a wakeup signal from the LAN. Enabled Enables Wake-up on LAN. Disabled Disables Wake-up on LAN (Default). The Wake-up LAN function support AC adapter mode only, before you plan to use this function please make sure your AC power source is connected to system properly. Do not install or remove an optional memory module while Wake-up on LAN is enabled.
Satellite A200/Satellite Pro A200 Chapter 8 Optional Devices Optional devices can expand the computer's capabilities and its versatility.
Optional Devices Express Card The computer (depending on the model) is equipped with an Express Card expansion slot that can accommodate two standard module formats; an Express Card/34 module and an Express Card/54 module. An Express Card module is a small, modular add-in card technology based on PCI Express and Universal Serial Bus (USB) interfaces. Installing an Express Card One Express Card connector is located on the right side of the computer.
Optional Devices Removing an Express Card 1. 2. 3. 4. Click the Safety Remove Hardware icon on the Task Bar. Click the Express Card you want to remove. Press the Express Card once to extend it. Grasp the extended Express Card, and remove it.
Optional Devices SD/SDHC/MMC/MS/MS Pro/xD Memory cards The computer is equipped with a multiple digital media card slot that can accommodate SD/SDHC/MMC/MS/MS Pro/xD memory cards. These memory cards let you easily transfer data from devices, such as digital cameras and Personal Digital Assistants, which use flash-memory.
Optional Devices Installing a memory card To install a memory card: 1. Insert the memory card. 2. Press gently to ensure a firm connection. Inserting a memory card Make sure the memory card is oriented properly before you insert it. If Windows® fails to read the card, remove it then re-insert it. ■ The multiple digital media card slot only accepts one type of card at a time. Do not attempt to install more than one card as you risk damaging either the cards themselves or the computer.
Optional Devices ■ Make sure the memory card indicator is out before you remove the card or turn off the computer's power. If you remove the card or turn off the power while the computer is accessing the card you may lose data or damage the card. ■ Do not remove the card while the computer is in Sleep or Hibernation mode. The computer could become unstable or data in the memory card could be lost.
Optional Devices Memory expansion You can install additional memory in the computer's memory module socket to increase the amount of RAM. This section describes how to install and remove a memory module. ■ Before you install or remove a memory module, turn off the computer with the Shut Down option in the Windows Start menu. If you install or remove a memory module while the computer is in Sleep or Hibernation mode, data will be lost.
Optional Devices 5. Slide your fingernail or a thin object under the cover and lift it off. Removing the memory module socket cover 6. Fit the module's connectors into the computer's connectors at about a 45 degree angle and press the module carefully to ensure a firm connection. Do not touch the connectors on the memory module or on the computer. Debris on the connectors may cause memory access problems. 7. Push the module down so it lies flat.
Optional Devices 8. Seat the cover and secure it with the screw. 9. Replace the battery pack as described in Chapter 6, Power and PowerUp Modes. 10. Turn the power on and make sure the added memory is recognized. Removing Memory on Bottom Side If you use the computer for a long time, the memory modules will become hot. In this case, let the memory modules cool to room temperature before you replace them. To remove the memory module, make sure the computer is in boot mode then: 1.
Optional Devices Additional battery pack You can increase the portability of the computer with additional battery packs. If you're away from an AC power source and your battery runs low, you can replace it with a freshly charged battery. See Chapter 6, Power and Power-Up Modes. Additional AC adapter If you frequently carry the computer to different sites such as your home and office, having an AC adapter at each location reduces the weight and bulk of your load.
Optional Devices Television A television can be connected to the video out port on the computer. To connect a television, follow the steps below. 1. Turn the computer off. 2. Use a video cable (not supplied) to connect the television to the video out port. 3. Turn the television on. 4. Turn the computer on. You can use the hotkeys Fn + F5 or use the TV-Out button to change the display device. Refer to Chapter 5, The Keyboard.
Optional Devices 3. Click the Advanced Setting button. The Generic PnP Monitor and Intel® 945GM Express Chipset Family dialogue box opens. 4. Click the Graphics Properties button.
Optional Devices 5. In the subsequent dialogue box, click Display Devices and then set up your television and notebook displays. For nVidia 1. Click Start > Control Panel > Personalization. 2. Choose Display Settings.
Optional Devices 3. Click the Advanced Settings button. The Generic PnP Monitor and NVIDIA GeForce Go 7300 Properties dialogue box opens. 4. Click Start the NVIDIA Control Panel.
Optional Devices 5. Click Display item. 6. Click Change Display Configuration item. 7. Setup your television and notebook display.
Optional Devices i.LINK (IEEE1394) i.LINK (IEEE1394) is used for high-speed data transfer for a range of compatible devices such as: ■ Digital video cameras ■ Hard disk drives ■ MO drives ■ Optical disc drives i.LINK uses a four-pin connector, which does not carry electric current. External devices will need their own power supply. Precautions ■ Make a back-up of your data before transferring it to the computer. There is a possibility that the original data will be damaged.
Optional Devices Security lock A security lock enables you to anchor your computer to a desk or other heavy object to help prevent unauthorized removal of the computer. Attach one end of a cable to the desk and the other end to the security lock slot on the right side of the computer.
Optional Devices 8-18 Satellite A200/Satellite Pro A200
Satellite A200/Satellite Pro A200 Chapter 9 Troubleshooting TOSHIBA designed the computer for durability. However, should problems occur, following the procedures in this chapter can help to determine the cause. All readers should become familiar with this chapter. Knowing what might go wrong can help prevent problems from occurring. Problem solving process Resolving problems will be much easier if you observe the following guidelines: ■ Stop immediately when you recognize a problem exists.
Troubleshooting Preliminary checklist Consider the simplest solution first. The items in this checklist are easy to fix and yet can cause what appears to be a serious problem. ■ Make sure you turn on all peripheral devices before you turn on the computer. This includes your printer and any other external device you are using. ■ Before you attach an external device, turn the computer off. When you turn the computer back on it recognizes the new device.
Troubleshooting Software The problems may be caused by your software. If you cannot load a software package, the media may be damaged or the program might be corrupted. Try loading another copy of the software. If an error message appears while you are using a software package, check the software documentation. These documents usually include a problem solving section or a summary of error messages. Next, check any error messages in the operating system documentation.
Troubleshooting System start-up When the computer does not start properly, check the following items: ■ Self Test ■ Power Sources ■ Power-on Password Self test When the computer starts up, the self test will be run automatically, and the following will be displayed: (This screen image is one of the examples. You may see the different screen image depending on the model you purchased.) This message remains on the screen for a few seconds.
Troubleshooting Power When the computer is not plugged into an AC outlet, the battery pack is the primary power source. However, your computer has a number of other power resources, including an intelligent power supply and Real Time Clock battery. These resources are interrelated and any one could affect apparent power problems. This section provides check lists for AC power and the battery. If you cannot resolve a problem after following them, the cause could lie with another power resource.
Troubleshooting Battery If you suspect a problem with the battery, check the DC IN indicator as well as the indicators for the battery. For information on indicators and battery operation see Chapter 6, Power and Power-Up Modes. Problem Procedure Battery doesn't power the computer. The battery may be discharged. Connect the AC power cord to charge the battery. Battery doesn't charge when the AC power cord is attached. (Battery indicator does not glow amber.
Troubleshooting Keyboard Keyboard problems can be caused by your setup configuration. For more information refer to Chapter 5, The Keyboard. Problem Procedure Some letter keys produce numbers. Check that the numeric keypad overlay is not selected. Press Fn + F10 and try typing again. Output to screen is garbled. Make sure the software you are using is not remapping the keyboard. Remapping involves reassigning the meaning of each key. See your software's documentation.
Troubleshooting Hard disk drive Problem Procedure Computer does not boot from hard drive. Insert a system disk and reboot. There may be a problem with your operating system files. Refer to your operating system documentation. Slow performance Your files may be fragmented. Run SCANDISK and defragmenter to check the condition of your files and disk. Refer to your operating system documentation or online HELP for information on running SCANDISK and the defragmenter.
Troubleshooting Wireless LAN If the following procedures do not restore LAN access, consult your LAN administrator. For more information on wireless communication, refer to Chapter 4, Operating Basics. Problem Procedure Cannot access Wireless Make sure the computer's wireless LAN communication switch is set to on. Use the ConfigFree program that comes preinstalled in your computer to see LAN status. If problems persist, consult your LAN administrator.
Troubleshooting Sound system Problem Procedure No sound is heard Adjust the volume control dial. Check the software volume settings. If appropriate, make sure the headphone connection is secure. Check Windows Device Manager and ensure the sound function is enabled and that settings for I/O address, interrupt level and DMA are correct for your software and do not conflict with other hardware devices that you have connected to the computer. If problems persist, contact your dealer.
Troubleshooting USB mouse Problem Procedure On-screen pointer does The system might be busy. If the pointer is shaped not respond to mouse as an hourglass, wait for it to resume its normal movement shape and try again to move it. Make sure the mouse is properly connected to the USB port. Double-clicking does not work Try changing the double-click speed setting in the mouse control utility. 1. Open the Control Panel, select the Mouse icon and press Enter. 2. Click the Buttons tab. 3.
Troubleshooting TV output signal Problem Procedure Display on TV is poor Make sure the TV type is correct for your area: NTSC (US) or PAL (Europe). No display Try adjusting the contrast and brightness controls on the external monitor. Press hotkeys Fn + F5 to change the display. Refer to Chapter 5, The Keyboard. If problems persist, contact your dealer.
Troubleshooting Problem Procedure The computer hangs up and issues beep sounds. (A long beep, three short beeps, three short beeps, and then a long beep.) Make sure the memory module installed in the expansion slot is compatible with the computer. If an incompatible module has been installed, follow the steps below. 1. Turn off the power. 2. Disconnect the AC adapter and all peripheral devices. 3. Remove the battery pack. 4. Remove the memory module. 5.
Troubleshooting Problem Procedure In data transmission, make sure the parity bit and Character display stop bit settings correspond with those of the becomes garbled during a communication remote computer. Check the flow control and communication protocol. You cannot receive an incoming call Check the "rings before auto answer" setting in your communications application. If problems persist, contact your dealer. CD-RW/DVD-ROM drive For more information, refer to Chapter 4, Operating Basics.
Troubleshooting Problem Procedure Cannot write correctly If you have trouble writing, make sure you are observing the following precautions: ■ Use only media recommended by TOSHIBA. ■ Do not use the mouse or keyboard during writing. ■ Use only the software supplied with the computer for recording. ■ Do not run or start other software during writing. ■ Do not jar the computer during writing. ■ Do not connect/ disconnect external devices or install/remove internal cards during writing.
Troubleshooting Problem Procedure The software or hardware configuration may be Some discs run correctly, but others do causing a problem. Make sure the hardware configuration matches your software's needs. not Check the disc's documentation. Check the type of disc you are using.
Troubleshooting Real Time Clock Problem Procedure The following message is displayed on the LCD: ERROR 271: Check date and time settings. WARNING 0251: System CMOS checksum bad Default configuration used. Press [F1] to resume, [F2] to Setup. The RTC battery charge has become exhausted, you should set the date and time in within the BIOS setup screen through the following steps: 1. Press [F1] key. BIOS setup will boot up. 2. Press [F2] to set the date in [System Date]. 3.
Troubleshooting TOSHIBA support If you require any additional help using your computer or if you are having problems operating the computer, you may need to contact TOSHIBA for additional technical assistance. Before you call Some problems you experience may be related to software or the operating system, it is important to investigate other sources of assistance first. Before contacting TOSHIBA, try the following: ■ Review troubleshooting sections in the documentation for software and peripheral devices.
Troubleshooting Where to write If you are still unable to solve the problem and suspect that it is hardware related, write to TOSHIBA at the nearest location listed below: Outside of Europe In Europe Australia TOSHIBA (Australia) Pty, Ltd. Information Systems Division 84-92 Talavera Road, North Ryde, N.S.W. 2113 Sydney Germany & Austria TOSHIBA Europe (I.E.) GmbH Geschäftsbereich, Deutschland-Österreich Hammfelddamm8, D-41460 Neuss, Germany Canada TOSHIBA of Canada Ltd.
Troubleshooting 9-20 Satellite A200/Satellite Pro A200
Satellite A200/Satellite Pro A200 Chapter 10 Disclaimers This chapter states the Disclaimer(s) information applicable to TOSHIBA computers. CPU Central Processing Unit (“CPU”) Performance Disclaimer.
Disclaimers 64-Bit Computing. 64-bit processors are designed to take advantage of 32 and 64 bit computing. 64-bit computing requires that the following hardware and software requirements are met: ■ 64-bit Operating System ■ 64-bit CPU, Chipset and BIOS (Basic Input/Output System) ■ 64-bit Device drivers ■ 64-bit applications Certain device drivers and/or applications may not be compatible with a 64bit CPU and therefore may not function properly.
Disclaimers HDD Drive Capacity 1 Gigabyte (GB) means 109 = 1,000,000,000 bytes using powers of 10. The computer operating system, however, reports storage capacity using powers of 2 for the definition of 1 GB = 230 = 1,073,741,824 bytes, and therefore shows less storage capacity. Available storage capacity will also be less if the product includes one or more pre-installed operating systems, such as Microsoft Operating System and/or pre-installed software applications, or media content.
Disclaimers Copy Protection Copy protection technology included in certain media may prevent or limit recording or viewing of the media. Images All images are simulated for purposes of illustration. LCD Brightness and Eye Strain Your LCD display has a brightness approaching that of a TV device. We recommend that you adjust the brightness of your LCD to a comfortable level to prevent possible strain on your eyes.
Satellite A200/Satellite Pro A200 Appendix A Specifications This appendix summarizes the computer's technical specifications. Dimensions 362mm (W) x 267.8mm (D) x 39.3mm (H. Max.) 362mm 267.8mm 39.
Specifications Weight Starting at 2.72kg / 5.99lbs* * Weight may vary depending on product configuration, vendor components, manufacturing variability and options selected.
Specifications Communication Protocol Data: ITU-T-Rec (Former CCITT) Bell Fax: ITU-T-Rec (Former CCITT) V.21/V.22/V.22bis/ V.32/ V.32bis/V.34/ V.90/ V.92(only for USA and Canada) 103/212A V.17/V.29/V.27ter /V.21 ch2 Communication Speed Data transmission and reception 300/1200/2400/4800/7200/9600/12000/14400/ 16800/19200/21600/24000/26400/28800/ 31200/ 33600 bps Data reception only with V.90/V.
Specifications A-4 Satellite A200/Satellite Pro A200
Satellite A200/Satellite Pro A200 Appendix B Display Modes This appendix contains a table listing all the display modes when the display is set to an external monitor. If you are running some applications (for example a 3D application or video playback and so on), you may see some disturbance, flickering or frame dropping on your screen. If that occurs, adjust the resolution of display, lowering it until the screen is displayed properly. You could also disable Windows Aero™. to help correct this situation.
Display Modes Some of display mode might not be supported depending on the external monitor which you use. Displaying movies on a TV or CRT This section describes how to set up your system to display movies simultaneously on your computer's LCD and on an external TV or CRT monitor. To connect a television, follow the steps below. 1. Turn the computer off. 2. Use a video cable (not supplied) to connect the television to the video out port. 3. Turn the television on. 4. Turn the computer on.
Display Modes 3. Click the Advanced Setting button. The Generic PnP Monitor and Mobile Intel® 945GM Express Chipset Family dialogue box opens. 4. Click the Graphics Properties button.
Display Modes 5. In the subsequent dialogue box, click Display Devices and then set up your television and notebook displays. For nVidia 1. Click Start > Control Panel > Personalization. 2. Choose Display Settings.
Display Modes 3. Click the Advanced Settings button. The Generic PnP Monitor and NVIDIA GeForce Go 7300 Properties dialogue box opens. 4. Click Start the NVIDIA Control Panel.
Display Modes 5. Click Display item. 6. Click Change Display Configuration item. 7. Setup your television and notebook display.
Satellite A200/Satellite Pro A200 Appendix C AC Power Cord and Connectors The power cord's AC input plug must be compatible with the various international AC power outlets and the cord must meet the standards for the country/region in which it is used. All cords must meet the following specifications: Length: Minimum 1.7 meters Wire size: Minimum 0.75 mm2 Current rating: Minimum 2.5 amperes Voltage rating: 125 or 250 VAC (depending on country/region's power standards) Certification agencies U.S.
AC Power Cord and Connectors For the United States and Canada, two pin plug configuration must be a 215P (250V) or 1-15P (125V) and three pin plug coniguration must be 6-15P (250V) or 5-15P (125V) as designated in the U. S. National Electrical code handbook and the Canadian Electrical Code Part II. The following illustrations show the plug shapes for the U. S. A. and Canada, the United Kingdom, Australia and Europe.
Satellite A200/Satellite Pro A200 Glossary The terms in this glossary cover topics related to this manual. Alternate naming is included for reference.
Glossary SCSI: small computer system interface TFT: thin-film transistor USB: Universal Serial Bus VESA: Video Electronic Standards Association VGA: video graphics array WXGA: wide extended graphics array A adaptor: A device that provides an interface between two dissimilar electronic devices. For example, the AC adaptor modifies the power from a wall outlet for use by the computer.
Glossary capacity: The amount of data that can be stored on a magnetic storage device such as a floppy disk or hard disk. It is usually described in terms of kilobytes (KB), where one KB = 1024 bytes and megabytes (MB), where one MB = 1024 KB. CD-ROM: A Compact Disc-Read Only Memory is a high capacity disc that can be read from but not written to. The CD-ROM drive uses a laser, rather than magnetic heads, to read data from the disc.
Glossary D DC: Direct Current. Electric current that flows in one direction. This type of power is usually supplied by batteries. default: The parameter value automatically selected by the system when you or the program do not provide instructions. Also called a preset value. device driver: A program that controls communication between a specific peripheral device and the computer. The CONFIG.SYS file contains device drivers that MS-DOS loads when you turn the computer on.
Glossary G gigabyte (GB): A unit of data storage equal to 1024 megabytes.
Glossary L Light Emitting Diode (LED): A semiconductor device that emits light when a current is applied. Liquid Crystal Display (LCD): Liquid crystal sealed between two sheets of glass coated with transparent conducting material. The viewingside coating is etched into character forming segments with leads that extend to the edge of the glass. Applying a voltage between the glass sheets alters the brightness of the liquid crystal. LSI: Large Scale Integration.
Glossary P parity: 1) The symmetrical relationship between two parameter values (integers) both of which are either on or off; odd or even; 0 or 1. 2) In serial communications, an error detection bit that is added to a group of data bits making the sum of the bits even or odd. Parity can be set to none, odd, or even. peripheral device: An I/O device that is external to the central processor and/or main memory such as a printer or a mouse. pixel: A picture element.
Glossary T terminal: A typewriter-like keyboard and CRT display screen connected to the computer for data input/output. TFT display: A liquid crystal display (LCD) made from an array of liquid crystal cells using active-matrix technology with thin film transistor (TFT) to drive each cell. TouchPad/Dual Mode Pad: A pointing device integrated into the TOSHIBA computer palm rest.
