Toshiba Personal Computer Satellite Maintenance Manual TOSHIBA CORPORATION [CONFIDENTIAL]
Copyright © 2009 by Toshiba Corporation. All rights reserved. Under the copyright laws, this manual cannot be reproduced in any form without the prior written permission of Toshiba. No patent liability is assumed with respect to the use of the information contained herein. Toshiba Personal Computer Satellite Maintenance Manual First edition May. 2009 Disclaimer The information presented in this manual has been reviewed and validated for accuracy.
Preface This maintenance manual describes how to perform hardware service maintenance for the Toshiba Personal Computer Satellite, referred to as the Satellite Series in this manual. The procedures described in this manual are intended to help service technicians isolate faulty Field Replaceable Units (FRUs) and replace them in the field. SAFETY PRECAUTIONS Four types of messages are used in this manual to bring important information to your attention.
The manual is divided into the following parts: Chapter 1 Hardware Overview describes the Satellite Series system unit and each FRU. Chapter 2 Troubleshooting Procedures explains how to diagnose and resolve FRU problems. Chapter 3 Test and Diagnostics describes how to perform test and diagnostic operations for maintenance service. Chapter 4 Replacement Procedures describes the removal and replacement of the FRUs.
Some operations require you to simultaneously use two or more keys. We identify such operations by the key top symbols separated by a plus (+) sign. For example, Ctrl + Pause (Break) means you must hold down Ctrl and at the same time press Pause (Break). If three keys are used, hold down the first two and at the same time press the third.
Table of Contents Chapter 1 Hardware Overview 1.1 Features.............................................................................................................................1-1 1.2 2.5-inch HDD .................................................................................................................1-11 1.3 DVD Super Multi (+-R Double Layer) ..........................................................................1-13 1.4 Power Supply...............................................
2.16 7 in 1 card Troubleshooting...............................................................................................44 2.17 HDD Troubleshooting .........................................................................................................46 2.18 CRT failure Troubleshooting...............................................................................................48 2.19 HDMI Troubleshooting ......................................................................................
3.15 BUTTON Test……..…………...………….…….……… .……..…………...……............24 3.16 1st HDDTest ……………………………....……………. .……………....….…………...26 3.17 RDMI Test………………...………………………….… .……………...…..…………….27 3.18 WDMI Test …………….…………………………….…………….…....…. .…………..28 Chapter 4 4.1 Replacement Procedures General ................................................................................................................................4-1 Safety Precautions................................................................
Installing the ODD Bay Module ...................................................................................... 4-20 Disassembling the ODD Drive ........................................................................................ 4-20 Assembling the ODD Drive ............................................................................................. 4-21 4.8 Keyboard Cover and Keyboard........................................................................................
Removing the Motherboard ..............................................................................................4-36 Installing the Motherboard................................................................................................4-38 4.18 VGA Board and VGA Thermal Module (Optional) .........................................................4-40 Removing the VGA Board and VGA Thermal Module ...................................................
Figures Figure 4.1 Removing the Battery Pack.................................................................................... 4-8 Figure 4.2 Removing the HDD door ..................................................................................... 4-10 Figure 4.3 Removing the HDD from the HDD bay............................................................... 4-11 Figure 4.4 Removing the HDD plate ..................................................................................... 4-11 Figure 4.
Figure 4.30 Align the DP CONN, S/PDIF CONN, Audio CONN and RJ45 CONN...............4-38 Figure 4.31 Installing the DC-in jack .......................................................................................4-39 Figure 4.32 Removing the VGA Board....................................................................................4-40 Figure 4.33 Reapply the Shinetsu 7726 grease on the thermal module and remove any release papers....................................................................
(low-end model) ................................................................................................... 4-59 Figure 4.59 Removing the LCD Hinge Assembly................................................................... 4-60 Figure 4.60 Removing the LVDS cable from the LCD module.............................................. 4-61 Figure 4.61 Installing the LCD Hinge Assembly .................................................................... 4-62 Figure 4.
Chapter 1 Hardware Overview
1 Hardware Overview Chapter 1 Contents 1.1 Features .................................................................................................................. 1-1 1.2 2.5-inch HDD ....................................................................................................... 1-11 1.3 DVD Super Multi (+-R Double Layer) ................................................................ 1-13 1.4 Power Supply ...............................................................................
1 Hardware Overview Figures Figure 1-1A ID Parts Description Placement Part A.......................................................... 1-7 Figure 1-2 SATA HDD ................................................................................................. 1-11 Figure 1-3 DVD Super Multi Drive .............................................................................. 1-13 Tables Table 1-1 HDD Specifications .....................................................................................
Error! Style not defined. Error! Style not defined. 1.1 1 Hardware Overview Features The Toshiba Satellite A500/A500D is a full-size PC notebook based on a Dual Core Processor, providing high-speed processing capabilities and advanced features. The computer employs a lithium ion battery that allows it to be battery-operated for a long period of time. The display uses 16.0-inch WXGA LCD panel. The PGA socket supports BTO for the CPU so that the system can be designed to suit your needs.
1 Hardware Overview Error! Style not defined. Error! Style not defined. ODD (BTO) 12.7mm height DVD Super Multi drive supporting ±R Double Layer 12.7mm height DVD Super Multi drive supporting ±R Double Layer w/ Labelflash Display (BTO) The LCD displays available come with one of the following types: 16.0" COLOR TFT/HD LCD (Samsung LTN160AT01-A Glare), 1366 X 768 HD Resolution 16.
Error! Style not defined. Error! Style not defined. 1 Hardware Overview Universal Serial Bus (USB) Ports The computer has three USB 2.0 ports. It is supported to daisy-chain a maximum of 127 USB devices. The serial data transfer rate is 480 Mbps or 12 Mbps and 1.5 Mbps. These ports support PnP installation and hot plugging. They also support Sleep and Charge function.
1 Hardware Overview Error! Style not defined. Error! Style not defined. Headphones/S/PDIF/Line out Jack This jack connects digital speakers or stereo headphones (16 ohm minimum). When connected to digital speakers or headphones, the internal speaker is automatically disabled. This jack can also be used as a S/PDIF port and can enable connection of optical-digital correspondence devices. Microphone/ Line-in Jack A 3.
Error! Style not defined. Error! Style not defined. 1 Hardware Overview Felica (BTO) Imbedded Felica module writes and reads data to and from contact less Felica IC cards. Having no need for physical contact with the card, the Reader/Writer is immune to performance deterioration caused by wear and contamination, providing easy maintenance and long-term reliability.
1 Hardware Overview Error! Style not defined. Error! Style not defined. DislpayPort (BTO) A 20-pin DisplayPort is installed on some computers to send and receive HD and SD video and audio signals (similar to HDMI). Support Display port1.0 and 1.1 protocols for dual mode adapter. TV Tuner (BTO) Some models are equipped with ATSC/NSTC for Express card type TV tuner and PCIE mini type for the reception and playback of DVBT.
Error! Style not defined. Error! Style not defined. 1 Hardware Overview Figure 1-1A shows the computer and its system unit configuration.
1 Hardware Overview Satellite A500D Maintenance Manual Error! Style not defined. Error! Style not defined.
Error! Style not defined. Error! Style not defined. 1 Hardware Overview The system unit of the computer consists of the following components: Processor (BTO) The computer is equipped with one of the following AMD ® processors. AMD TurionTM 64 X2 Dual-Core Processor AMD AthlonTM X2 Dual-Core Processor AMD SableTM Processor Memory (BTO) The computer has two SODIMM slots that come standard with 512MB/1GB/2GB/4GB, BTO for various memory requirements. It can incorporate up to 8 GB of main memory.
1 Hardware Overview Error! Style not defined. Error! Style not defined. Graphics Controller AMD RS780MN/RS780MC as integrated graphics solution Following External Graphic solution with AMD M780G/M770 ATI Mobility RadeonTM HD 3470 (512MB) ATI Mobility RadeonTM HD 3650 (1GB) HDMI 1.
Error! Style not defined. Error! Style not defined. 1.2 1 Hardware Overview 2.5-inch HDD The computer contains an extremely low-profile and lightweight, high-performance HDD. The HDD incorporates 9.5 mm / 12.5 mm height magnetic disk and mini-Winchester type magnetic heads. The HDD interface conforms to Serial ATA. Storage capacities supported are 120, 160, 200, 250, 320 and 500 GB. The HDD is shown in Figure 1-2 and some of its specifications are listed in Table 1-1.
1 Hardware Overview Error! Style not defined. Error! Style not defined. Table 1-1 HDD Specifications Specifications Item Capacity (GB) 120GB 160 GB 200 250 GB Rotational Speed (RPM) 5400 or 7200 RPM 5400 or 7200 RPM 7200 RPM 5400 RPM 9.5 mm 9.5 mm 9.5 mm 9.
Error! Style not defined. Error! Style not defined. 1.3 1 Hardware Overview DVD Super Multi (+-R Double Layer) The DVD Super Multi drive accepts 12-cm (4.72-inch) and 8-cm (3.15-inch) discs. At maximum, the drive can play back a DVD at 8x speed, read CD-ROM at 24x speed, and write CD-R at 24x speed, CD-RW at 6x speed, CD-RW at 16x speed, DVD-R at 8x speed, DVD-RW at 8x speed, DVD+R at 8x speed, DVD+R (Double Layer) at 8x speed, DVD-R (Dual Layer) at 8x speed, DVD+RW at 8x speed and DVD-RAM at 5x speed.
1 Hardware Overview 1.4 Error! Style not defined. Error! Style not defined. Power Supply The power supply unit provides constant voltage (19V) for the system board and performs the following functions: 1. Power input monitor Checks whether the AC adapter (DC power supply) is connected to the computer. Checks whether the battery pack is connected to the computer. Monitors the DC power supply input voltage (AC Adapter output voltage). 2.
Error! Style not defined. Error! Style not defined. 1 Hardware Overview 6. Output monitor Monitors the voltage output to the system block (load/logic circuit side). Monitors the voltage, over-voltage, input/output current of the battery pack. Monitors the internal temperature of the battery pack. Monitors the supply voltage from the AC adapter.
1 Hardware Overview 1.5 Error! Style not defined. Error! Style not defined. Batteries The computer has the following two types of batteries: Main Battery Pack Real Time Clock (RTC) Battery 1.5.1 Main Battery The main battery pack serves as the computer's main power source when the AC adapter is not attached. The main battery maintains the state of the computer when the AC adapter is detached . 1.5.2 Battery Charging Control Battery charging is controlled by EC KB926.
Error! Style not defined. Error! Style not defined. 1 Hardware Overview NOTE: The time required for normal charge depends on the power consumption by the system. Using a fluorescent lamp and frequently accessing the disk consumes more power and lengthen the charge time. Any of the following can stop battery charge: 1. The battery becomes fully charged. 2. The AC adapter or battery pack is removed. 3. The battery or AC adapter voltage is abnormal.
Chapter 2 Troubleshooting Procedures
2 Troubleshooting Procedures Chapter 2 Contents 2.1 Troubleshooting Introduction ...................................................................................... 3 2.2 Troubleshooting Flowchart ……………………………………………………………4 2.3 Power Supply Troubleshooting......................................................................................9 2.4 Display Troubleshooting..............................................................................................14 2.5 Keyboard Troubleshooting ..
2 Troubleshooting Procedures Figures Figure 2-1 Troubleshooting flowchart (1/2) ....................................................................... 5 Figure 2-1 Troubleshooting flowchart (2/2) ...................................................................... 6 Figure 2-3 Display troubleshooting process ..................................................................... 14 Figure 2-4 Keyboard troubleshooting process ..................................................................
2 Troubleshooting Procedures Tables Table 2-1 Battery LED ........................................................................................................10 Table 2-2 DC-IN LED.........................................................................................................11 2.1 Troubleshooting Introduction Chapter 2 describes how to determine if a Field Replaceable Unit (FRU) in the computer is causing the computer to malfunction. The FRUs covered are: 1. Display 7. Speaker 13.
2 Troubleshooting Procedures 12. Headphones 13. USB test module and USB cable 14. Music CD 15. MIC module and MIC line 16. SPDIF line 17. Finger print module 18. TV tuner signal generator 19. FM tuner signal generator 20. E-SATA HDD 21. Felica card 22. UWB signal generator 23. Remote controller. 2.2 Troubleshooting Flowchart If you know the location of the malfunction, turn directly to the appropriate section of this chapter.
2 Troubleshooting Procedures START C o n n e c t th e A C a d a p te r to th e D C IN s o c k e t Is th e D C -IN L E D o n ? No P e rfo rm th e P o w e r S u p p ly T ro u b le s h o o tin g p ro c e d u re s in s e c tio n 2 .3 Y es Is th e B a tte ry L E D o n ? No P e rfo rm th e P o w e r S u p p ly T ro u b le s h o o tin g p ro c e d u re s in s e c tio n 2 .3 No P e rfo rm th e P o w e r S u p p ly T ro u b le s h o o tin g p ro c e d u re s in s e c tio n 2 .
2 Troubleshooting Procedures A Does typed characters appear correctly? No Perform the Keyboard Troubleshooting procedures in section 2.6 No Perform the USB memory disk Troubleshooting procedures in section 2.5 Yes After confirming which diagnostics test has detected an error, perform the appropriate procedure as outlined below. Yes Insert USB memory disk, Then run the diagnostics test program.
2 Troubleshooting Procedures If the diagnostics program cannot detect an error, the problem may be intermittent. The test program should be executed several times to isolate the problem. When a problem has been located, perform the appropriate troubleshooting procedures as follows: 1. If an error is detected by the battery test, perform the Power Supply Troubleshooting procedures in Section 2.2 2. If an error is detected by the display test, perform the Display Troubleshooting procedures in Section 2.3 3.
2 Troubleshooting Procedures Other problems that are not covered by the diagnostics program may be discovered by a user. 1. If an error is detected when using an external USB device, perform the External USB Devices Troubleshooting procedures in Section 2.5 2. If an error is detected when using the TV-out connection, perform the TV-Out Failure Troubleshooting procedures in Section 2.6 3. If an error is detected when using the modem, perform the Modem Troubleshooting procedures in Section 2.10 4.
2 Troubleshooting Procedures 2.
2 Troubleshooting Procedures The power supply controls many functions and components. To determine if the power supply is functioning properly, start with Procedure 1 and continue with the other Procedures as instructed. The flowchart in Figure 2-2 gives a summary of the process.
2 Troubleshooting Procedures Table 2-2 DC-IN LED AC-IN LED Power supply status Solid on AC power exists (LED is solid White). Off No AC power exists. To check the power supply status, install a battery pack and connect an AC adaptor to the DC-IN port on the computer and to a power supply. If the DC-IN LED or Battery LED is not lit, go to Procedure 2. Procedure 2 Adaptor / battery replacement A faulty adaptor may not supply power or may not charge the battery. Perform Check 1.
2 Troubleshooting Procedures Procedure 3 Power supply connection check The power supply wiring diagram is shown below: AC adaptor cord AC power cord AC adaptor System board Battery Any of the connectors may be disconnected. Perform Check 1. Check 1 Disconnect the AC power cord from wall outlet. Check the power cable for breaks. If the power cord is damaged, connect a new AC power cord. If there is no damage, go to Check 2.
2 Troubleshooting Procedures Procedure 4 Diagnostic check The power supply may not charge the battery pack. Perform the following procedures: 1. Reinstall the battery pack. 2. Attach the AC adaptor and turn on the power. If you cannot turn on the power, go to Procedure 5. 3. Run the Diagnostic test following the procedures described in Chapter 3, Tests and Diagnostics. If no problem is detected, the battery is functioning normally.
2 Troubleshooting Procedures 2.4 Display Troubleshooting STA RT P e r fo r m e x te r n a l d is p la y c h e c k (P r o c e d u re 1 ) D o e s th e e x te r n a l d is p la y f u n c tio n o k ? No P e r fo r m d ia g n o s tic c h e c k ( P ro c e d u r e 2 ) Y es W a s a d is p la y p ro b le m d e te c te d ? No D is p la y is n o t f a u lty . C o n tin u e tro u b le s h o o tin g re fe r to F ig u re 2 .
2 Troubleshooting Procedures This section describes how to determine if the computer’s display is functioning properly. The process is outlined in Figure 2-3. Start with Procedure 1 and continue with the other procedures as instructed. Procedure 1: External display check Procedure 2: Diagnostic check Procedure 3: Connector and replacement check Procedure 1 External display check Connect an external display to the computer’s external monitor port, and then boot the computer.
2 Troubleshooting Procedures Procedure 3 Connector and replacement check The FL inverter board, LCD module, and system board are connected to the display circuits. Any of these components may be damaged. Refer to Chapter 4, Replacement Procedures, for instructions on how to disassemble the computer and then perform the following checks: Check 1 Make sure the DDR RAM module is seated properly. Test display again. If the problem still exits, replace the DDR RAM module.
2 Troubleshooting Procedures 2.5 Keyboard Troubleshooting ST A R T P e r fo rm e x te rn a l k e y b o a rd c h e c k (P ro c ed u re 1 ) D o e s th e e x te rn a l k e y b o a rd fu n c tio n o k ? Y es P e rfo rm d ia g n o s tic c h e c k (P ro ce d u re 2 ) N o W as a k ey b o ard p ro b le m d e te c te d ? N o K e y b o a rd is n o t fa u lty . C o n tin u e tro u b le s h o o tin g -re fe r to F ig u r e 2 .
2 Troubleshooting Procedures Procedure 1 External keyboard check Connect a USB keyboard to one of the computer’s USB ports, and then boot the computer. The computer automatically detects the external keyboard. If the external keyboard works correctly, the internal keyboard or its connections may be faulty. Go to Procedure 2. If the external keyboard appears to have the same problem as the internal keyboard, the system board may be having some problem.
2 Troubleshooting Procedures 2.
2 Troubleshooting Procedures To determine if the computer’s external USB devices are functioning properly, perform the following procedures. Figure 2-5 outlines the process. Start with Procedure 1 and continue as instructed. Procedure 1: External device and connection check Procedure 2: Replace system board Procedure 1 External device and connection check The USB device may be damaged or the connection may be faulty. Use windows application to check device can work fine or not, Perform Check 1.
2 Troubleshooting Procedures 2.
2 Troubleshooting Procedures A D o e s re p la c e m e n t T V T u n e r A n te n n a fu n c tio n p ro p e rly ? Y es R e p la c e T V T u n e r A n te n n a Y es R e p la c e T V T u n e r M o d u le No P e rfo rm T V T u n e r M o d u le c o n n e c tio n c h e c k (P ro c e d u re 4 ) D o e s re p la c e m e n t T V T u n e r M o d u le fu n c tio n p ro p e rly ? R e p la c e s y s te m b o a rd END Satellite A500D/Satellite A505D/Satellite A507D/Satellite Pro Series Maintenance Manual22
2 Troubleshooting Procedures To determine if the computer’s TV Tuner port is functioning properly, perform the following procedures. Figure 2-6 outlines the process. Start with Procedure 1 and continue as instructed. Procedure 1: TV Tuner cable connection check Procedure 2: TV Tuner SG setting check Procedure 3: TV Tuner Antenna connection check Procedure 4: TV Tuner Module connection check Procedure 1 TV tuner Cable connection check The TV Tuner cable may be damaged or the connections may be loose.
2 Troubleshooting Procedures replacement Antenna does not work the TV tuner Module may be damaged. Go to Procedure 4. Procedure 4 TV Tuner Module Connection check The TV Tuner Module connect may be faulty. Perform Check 1: Check 1 Check the TV Tuner Module is firmly plugged into system board, if connection was correctly, go to check 2. Check 2 Try connecting a different TV tuner Module to the computer. If the replacement TV tuner Module works, the original Module may be damaged.
2 Troubleshooting Procedures 2.
2 Troubleshooting Procedures To determine if the computer’s built-in TouchPad is functioning properly, perform the following procedures. Figure 2-7 outlines the process. Start with Procedure 1 and continue as instructed. Procedure 1: TouchPad connection check Procedure 2: TouchPad replacement check Procedure 1 TouchPad connection check The TouchPad is connected via the TouchPad FPC to the system board. Make sure the TouchPad FPC cable is firmly connected to the TouchPad and system board.
2 Troubleshooting Procedures 2.9 Speaker Troubleshooting START P e rfo rm a u d io s o u rc e te s t (P ro ced u re 1 ) D o a ll s o u rc e s h a v e s a m e p ro b le m ? No S p ea k e rs are n o t f a u lt y .
2 Troubleshooting Procedures To determine if the computer’s built-in speakers are functioning properly, perform the following procedures. Figure 2-8 outlines the process. First adjust the speaker volume to an appropriate level. Start with Procedure 1 and continue as instructed. Procedure 1: Audio source test Procedure 2: Earphone test Procedure 3: Connection check Procedure 4: Replacement check Procedure 1 Audio source test Try different audio sources (e.g.
2 Troubleshooting Procedures 2.10 Optical Drive Troubleshooting START Perform audio CD check (Procedure 1) Audio CD functions ok? No Perform drivecleaning check (Procedure 2) Yes Perform software check (Procedure 3) Perform diagnostic test (Procedure 4) Perform connection and replacement check (Procedure 5) Replace system board END Figure 2-9 Optical drive troubleshooting process This section describes how to determine if the computer’s internal optical drive is functioning properly.
2 Troubleshooting Procedures P200D Series Maintenance Manual module bays can accommodate the following optical drives: DVD SuperMulti supporting +-R Double Rayer Figure 2-9 outlines the process. Perform the steps below starting with Procedure 1 and continue with the other procedures as required. Procedure 1: Audio CD test Procedure 2: Drive cleaning check Procedure 3: Software check Procedure 4: Connection and replacement check Procedure 1 Audio CD check First, insert an audio CD into the CD/DVD drive.
2 Troubleshooting Procedures Procedure 4 Connection check and replacement check The optical drive connects to the system board. The drive may be disconnected, or the drive or system board may be damaged. Disassemble the computer following the steps described in Chapter 4, Replacement Procedures, and perform the following checks: Check 1 Make sure the drive is firmly connected to the system board. If the connection is good and there is still an error, go to Check 2.
2Troubleshooting Procedures 2.
2Troubleshooting Procedures This section describes how to determine if the computer's modem is functioning properly. Figure 2-10 outlines the process. Perform the steps below starting with Procedure 1 and continuing with the other procedures as required. Procedure 1: Telephone line connection check Procedure 2: Modem card connection check Procedure 3: Modem card replacement check Procedure 1 Telephone line connection check The telephone cable may be damaged or the connections may be loose.
2Troubleshooting Procedures 2.12 Express card Troubleshooting START P e rfo rm E x p re ss c a rd te st (P ro c e d u re 1 ) D o e rro rs o c c u r d u rin g E x p re ss c a rd te st? No E x p re ss c a rd u n it is n o t fa u lty .
2Troubleshooting Procedures This section describes how to determine if the Express card player is functioning properly. The process is summarized in Figure 2-11. Perform the steps below starting with Procedure 1 and continuing with the other procedures as required. Procedure 1: Express card test Procedure 2: Express card socket replacement check Procedure 1 Express card test The Express test card contains a Express test program. Use windows application to check device can work fine or not.
2Troubleshooting Procedures 2.13 Wireless LAN Troubleshooting START Perform diagnostic test (Procedure 1) W as a wireless LAN problem delected? No W ireless LAN system is not faulty. Continue troubleshooting - refer to Figure 2.
2Troubleshooting Procedures computer’s wireless LAN system is functioning properly, perform the following procedures. Figure 2-12 outlines the process. Start with Procedure 1 and continue with the other procedures as instructed. Procedure 1: Diagnostic test Procedure 2: Connector and replacement check Procedure 1 Diagnostic test Run the Diagnostic Program, which will automatically execute the wireless LAN Device check (refer to chapter 3 system configuration check).
2Troubleshooting Procedures 2.14 Camera Troubleshooting Figure 2-13 Camera troubleshooting process The Camera board or system board may be the reason of a Camera fault. Either of these two components may be damaged.
2Troubleshooting Procedures properly, perform the following procedures. Figure 2-13 outlines the process. Start with Procedure 1 and continue with the other procedures as instructed. Procedure 1: Windows Application test Procedure 2: Connector and replacement check Procedure 1 Windows Application test Run the functioning Program in windows, which will display the Camera test result. If tests and diagnostics result abnormal go to Procedure 2.
2Troubleshooting Procedures 2.15 Bluetooth Troubleshooting STA R T P r e f o r m d i a g n o s ti c te s t ( P ro c e d u re 1 ) W a s a B l u e to o th p r o b l e m d e te c t? B l u e to o th i s n o t f a u l ty . C o n ti n u e tr o u b l e s h o o ti n g - r e f e r to F i g u r e 2 . 1 P e r f o r m c o n n e c to r a n d re p la c e m e n t c h e c k ( P ro c e d u re 2 ) R e p l a c e B l u e to o th a n te n n a m o u d l e .
2Troubleshooting Procedures The Bluetooth antenna wire, Bluetooth module or system board may be the reason of a Bluetooth fault. Any of these components may be damaged. To determine if the computer’s Bluetooth is functioning properly, perform the following procedures. Figure 2-14 outlines the process. Start with Procedure 1 and continue with the other procedures as instructed.
2Troubleshooting Procedures Check 4 The system board may be damaged. Replace it with a new one following the instructions in Chapter 4.
2Troubleshooting Procedures 2.16 Bridge Media Slot Troubleshooting START Perform Bridge Media Slot test (Procedure 1) Do errors occur during Bridge Media Slot test? No Bridge Media Slot unit is not faulty. Yes Perform Bridge Media Slot replacement check (Procedure 2) Replace system board END Figure 2-15 Bridge Media Slot troubleshooting process This section describes how to determine if the Bridge Media Slot player is functioning properly. The process is summarized in Figure 2-15.
2Troubleshooting Procedures Procedure 1: Bridge Media Slot test Procedure 2: Bridge Media Slot replacement check Procedure 1 Bridge Media Slot test The Bridge Media Slot test PLS Use windows application to check device can work fine or not. Ensure the card in fully inserted into the socket before running the program. If an error occurs during the Bridge Media Slot test, perform Procedure 2. If no error occurs, it is likely that the original Bridge Media Slot was faulty.
2Troubleshooting Procedures 2.
2Troubleshooting Procedures The HDD/SSD or system board may be the reason of a HDD/SSD fault. Either of these two components may be damaged. To determine if the computer’s HDD/SDD is functioning properly, perform the following procedures. Figure 2-16 outlines the process. Start with Procedure 1 and continue with the other procedures as instructed.
2Troubleshooting Procedures 2.
2Troubleshooting Procedures Procedure 1: CRT connection check Procedure 2: CRT set check Procedure 1 CRT connection check The CRT cable may be damaged or the connections may be loose. Use windows application to check device can work fine or not. Perform Check 1: Check 1 Make sure CRT cable is firmly plugged into both the CRT set and the CRT port of the computer. If the cable is connected correctly, go to Check 2. Check 2 Make sure the CRT port is firmly secured to the system board of the computer.
2Troubleshooting Procedures 2.
2Troubleshooting Procedures Procedure 1: HDMI connection check Procedure 2: HDMI set check Procedure 1 HDMI connection check The HDMI cable may be damaged or the connections may be loose. Use windows application to check device can work fine or not. Perform Check 1: Check 1 Make sure HDMI cable is firmly plugged into both the HDMI set and the HDMI port of the computer. If the cable is connected correctly, go to Check 2.
2Troubleshooting Procedures 2.
2Troubleshooting Procedures Procedure 1: Display Port connection check Procedure 2: Display Port set check Procedure 1 Display Port connection check The Display port cable may be damaged or the connections may be loose. Use windows application to check device can work fine or not. Perform Check 1: Check 1 Make sure Display Port cable is firmly plugged into both the Display Port set and the Display Port of the computer. If the cable is connected correctly, go to Check 2.
2Troubleshooting Procedures 2.21 SPDIF troubleshooting Figure 2-20 SPDIF troubleshooting process The system board may be the reason of a SPDIF fault. The connector of system board may be damaged.
2Troubleshooting Procedures following procedures. Figure 2-20 outlines the process. Start with Procedure 1 and continue with the other procedures as instructed. Procedure 1: windows application test Procedure 2: Connector and replacement check Procedure 1 windows application test Use windows application to check device can work fine or not. If tests and diagnostics result abnormal go to Procedure 2. If an error is not located, the SPDIF is functioning properly.
2Troubleshooting Procedures 2.22 MIC Troubleshooting Figure 2.21. MIC troubleshooting process The MIC line or system board may be the reason of a MIC fault. Either of these two components may be damaged.
2Troubleshooting Procedures perform the following procedures. Figure 2-21 outlines the process. Start with Procedure 1 and continue with the other procedures as instructed. Procedure 1: Windows Application test Procedure 2: Connector and replacement check Procedure 1 Windows Application test Run the functioning Program (record.exe) on Windows model, which will display the MIC test result. If tests and diagnostics result abnormal go to Procedure 2.
2Troubleshooting Procedures 2.23 Finger printer troubleshooting Figure 2-22 Finger printer troubleshooting process The Finger printer board or system board may be the reason of a finger printer fault. Either of these two components may be damaged.
2Troubleshooting Procedures functioning properly, perform the following procedures. Figure 2-22 outlines the process. Start with Procedure 1 and continue with the other procedures as instructed. Procedure 1: windows application test Procedure 2: Connector and replacement check Procedure 1 windows application test Use windows application to check device can work fine or not .If an error is located, go to Procedure 2. If an error is not located, the Finger printer system is functioning properly.
2Troubleshooting Procedures 2.
2Troubleshooting Procedures A D o e s re p la c e m e n t F M T u n e r B o a rd fu n c tio n p ro p e rly ? Y es R e p la c e F M tu n e r b o a rd N o R e p la c e s y s te m b o a rd E N D To determine if the computer’s FM tuner port is functioning properly, perform the following procedures. Figure 2-23 outlines the process. Start with Procedure 1 and continue as instructed.
2Troubleshooting Procedures Check 1 Make sure FM Tuner Antenna is firmly plugged into FM Tuner port of the computer. If the Antenna is connected correctly, go to Check 2. Check 2 Try connecting a different FM Tuner Antenna to the computer. If the replacement FM Tuner Antenna works, the original set may be damaged. If the replacement set does not work the FM Tuner SG setting may be incorrect, Go to Procedure 2 Procedure 2 FM Tuner SG setting check The FM Tuner SG setting may be faulty.
2Troubleshooting Procedures 2.25 E-SATA Troubleshooting START Perform E-SATA device check (Procedure 1) Is E-SATA transmission ok? Yes Perform diagnostic check (Procedure 2) No Was an E-SATA problem detected? No E-SATA port and transmission are not faulty. Continue troubleshooting - refer to Figure 2.
2Troubleshooting Procedures Procedure 3: Connection and replacement check Procedure 1 E-SATA device check Connect an E-SATA device to the computer’s E-SATA port, then boot the computer for Windows Vista. The computer should automatically detect the E-SATA device. Check whether the device can transmit data to the computer. If the device is able to communicate with the computer, the problem may be intermittent or connections may be faulty. Go to Procedure 2.
2Troubleshooting Procedures 2.
2Troubleshooting Procedures To determine if the computer’s built-in Felica is functioning properly, perform the following procedures. Figure 2-25 outlines the process. Start with Procedure 1 and continue as instructed. Procedure 1: Felica connection check Procedure 2: Felica replacement check Procedure 1 Felica connection check The Felica is connected via the Felica FPC to the system board. Make sure the Felica FPC cable is firmly connected to the Felica and system board.
2Troubleshooting Procedures 2.
2Troubleshooting Procedures Procedure 1: UWB Antenna connection check Procedure 2: UWB SG setting check Procedure 3: UWB Module connection check Procedure 1 UWB Antenna connection check Use windows application to check device can work fine or not. If an error is located, make sure The UWB Antenna may be damaged or the connections may be loose. Perform Check 1: Check 1 Make sure UWB Antenna is firmly plugged into UWB module of the computer. If the antenna is connected correctly, go to Check 2.
2Troubleshooting Procedures 2.28 3G Troubleshooting START P e rf o r m d ia g n o s tic te s t (P r o c e d u re 1 ) W a s a 3 G p r o b le m d e te c te d ? No 3 G s y s te m is n o t fa u lty . C o n tin u e tro u b le s h o o tin g - r e f e r to F ig u r e 2 .
2Troubleshooting Procedures Procedure 1 Connector and replacement check The 3G antenna, 3G unit or system board may be disconnected or damaged. Disassemble the computer following the steps described in Chapter 4, Replacement Procedures, and perform the following checks. Check 1 Make sure that the 3G antenna is firmly connected to the 3G module (refer to Chapter 4 for instructions) and that the 3G module is securely slotted into the system board. If the problem persists, go to Check 2.
3 Tests and Diagnostics Chapter 3 Tests and Diagnostics Satellite A500D / Satellite A505D / Satellite A507D / Satellite Pro Series T&D
3. Tests and Diagnostics Contents 3.1 The Diagnostic Test ............................................................................................................ 3 3.2 Executing the Diagnostic Test............................................................................................. 4 3.3 Display Configuration ........................................................................................................ 8 3.4 Audio sound Test.....................................................
3 Tests and Diagnostics 3.1 The Diagnostic Test This chapter explains how to use the Test & Diagnostic program to test the functions of the (Base on Bradford 10AR/10ARG T&D version 1.0) hardware modules. The Test & Diagnostic Program is stored on the T&D diskettes. The program consists of a series of tests that run automatically when the Diagnostics Program items are selected and executed. NOTES: To start the diagnostics, follow these steps 1. Check all cables for loose connections. 2.
3. Tests and Diagnostics 3.2 Executing the Diagnostic Test DOS is required to run the DIAGNOSTICS PROGRAM. To start the DIAGNOSTIC PROGRAM, follow these steps: Insert the diagnostics USB disk drive and turn on the computer. (The diagnostics diskette contains the Free-DOS boot files.
3 Tests and Diagnostics The below display will show up at the beginning of T&D program If the test result passes, the following display will show up: Satellite A500D / Satellite A505D / Satellite A507D / Satellite Pro Series T&D
3. Tests and Diagnostics If an error is detected and a test fails, the following message displays: Then press any key for next actions – the below display presented if copying test log file onto diskette is necessary. This action will be executed when “Y” key pressed.
3 Tests and Diagnostics It will skip this process if “N” key pressed. And then it will check if it’s necessary to leave this program. Program will quit when “Y” key pressed and it will go back main menu for next test if “N” key pressed.
3. Tests and Diagnostics 3.3 Display Configuration This Item will show the unit configuration. It includes: CPU (CPU type) DDRAM SIZE Panel ID HDD1 type & capacity (Vendor ID. Model .
3 Tests and Diagnostics 3.4 Audio sound test The audio sound test allows the user to aurally confirm the speaker functions. And the speaker will send out music during test. NOTE: Remember to tune up the volume as “Maximum” before this test starts. Buffalo only have one speaker, no need test Left/Right Speaker The screen should display as below, indicating whether the test is passed or failed after the question.
3. Tests and Diagnostics 3.5 Fan ON/OFF Test The fan test allows the user to test aurally whether the fan is working. And follow the below procedures for this test: The computer will let the fan be “ON” after any key pressed. Feel the wind or listen the rotating sound to check whether the fan is working or not. NOTE: Remember to approach fan outlet that is near right side of unit whether fan is “ON”. The computer will stop the fan working after any key pressed.
3. Tests and Diagnostics 3.6 Main Battery Charge Test NOTE: The AC adaptor should be connected to successfully run this test . 75W with 19V DC for UMA SKU .
3. Tests and Diagnostics 3.7 Main Battery Change Test 3. 7 FDD Test NOTE: Before running the FDD test, prepare a formatted work diskette (1.44 MB). Need to insert FDD when power on machine. Otherwise the Floppy can not be detected. The Floppy Disk Test includes three subtests of the: 1. Sequential seek/verify function (Range: Track 0 ~ 79) 2. Funnel code seek/verify function (Range: Track 0 ~ 79) 3.
3. Tests and Diagnostics 3.8 Memory check This test will check if the computer’s Memory Frequency and Size is correct in every slot.
3 Tests and Diagnostics 3. 9 Keyboard Test The keyboard test checks the all keys function. NOTE: The Num Lock and the Overlay mode must be off to execute the keyboard test. Before keyboard test starts, the keyboard matrix code should be chosen as below display: 1. S (US, for America) 2. J (Japan, for Japan) 3. K(UK, for Europe) When you execute this test, the keyboard layout is drawn on the display. When any key is pressed, the corresponding key on the screen changes to black as shown below.
3.
3 Tests and Diagnostics UK keyboard 16 Satellite A500D / Satellite A505D / Satellite A507D / Satellite Pro Series T&D
3. Tests and Diagnostics NOTE: The “Fn” key cannot be tested in the keyboard test. To determine whether the “Fn” key is working correctly, press “Fn+F6 ” or “Fn+F7 ” keys to check if LCD display brightness change gradually. 3.10 Mouse (Pad) Test The Mouse test allows the user to select and assign values to the following, using the Touch Pad or “Tab” key to move between selections: 1. Mouse Speed (on a scale from slow to fast) 2. Acceleration (Off, Low, Medium, High) 3.
3. Tests and Diagnostics It will indicate whether the subtests pass or fail after three questions. NOTE: The above figure has three compartments although the Touch Pad installed may only have two buttons. In this case, the central compartment in the figure does not correspond to any button. 3.11 LCD Pixels Mode Test This LCD pixels mode test checks whether video display is fine. This test includes two modes of the test: 1. Text Mode - including 40*25 (16 colors) and 80*25 (2/16colors). 2.
3. Tests and Diagnostics 3.12 Magnetic Switch Test The Magnetic switch test checks the Magnetic function of the unit. When LCD cover closed, the Magnetic should enable to turn off the display. Follow below steps to run this test: 1. Close the LCD cover. 2. Open the LCD. Then it will indicate whether the test is passed or failed. 1>.
3. Tests and Diagnostics 2>.
3. Tests and Diagnostics 3.13 LAN Test The LAN test checks the LAN full-duplex environment. NOTE: LAN loopback needs to plug in before test begins. And LAN information will show on the test screen: IO Base – Port: A000H IRQ – BH, it’s “IRQ B”. Node – it is “MAC Address”. Line Speed – 1000Mbps or 100Mbps or 10 Mbps. Bus ID – it’s “14”. The LAN test includes three subtests of the: 1. Speed1000 2. Speed100 3. Speed10 The subtests run automatically.
3. Tests and Diagnostics The screen should display as below, indicating whether the subtests pass or fail when finished.
3.
3. Tests and Diagnostics 3.14 RTC Test Checks the computer’s RTC (Real Time Clock) and calendar functions by comparing the DOS and CMOS values. The test runs automatically. The screen should display as below, indicating whether the test is passed or failed when finished.
3. Tests and Diagnostics 3.15 BUTTON TEST NOTE: Only for five buttons SKU.
3. Tests and Diagnostics Mechanical type buttons x 8 to relate with above showed.
3. Tests and Diagnostics 3.16 1st HDD Test The HDD test allows the user to verify the 1st HDD ok or not.
3.
3. Tests and Diagnostics 3.
3. Tests and Diagnostics 3.18 Write DMI When you want to write DMI data, please select which data you want to write, the figure below will be displayed: 1.
3. Tests and Diagnostics 2. Write Version 3. Write Serial 4.
3. Tests and Diagnostics NOTE: should input correct DMI data, and should reboot the system that can make the setting effective.
3. Tests and Diagnostics 3. 19 3D Sensor Test This test will check 3D Sensor function by your computer successful or not.
3.
3. Tests and Diagnostics NOTE: Steps 4 Go on Turn run 90 degree whirl, then click enter to test NOTE: Step5 Go on Turn run 90 degree whirl, then click enter to test Check test result as below picture, PASS will show “OK”, FAIL will show “NG”.
3.
3.
Chapter 4 Replacement Procedures
4 Replacement Procedures Chapter 4 4.1 Contents General ................................................................................................................... 4-1 Safety Precautions .......................................................................................... 4-2 Before You Begin........................................................................................... 4-4 Disassembly Procedures.................................................................................
4 Replacement Procedures Installing the Keyboard Cover and Keyboard.............................................. 4-24 4.9 Logic Upper Assembly......................................................................................... 4-25 Removing the Logic Upper Assembly ......................................................... 4-25 Installing the Logic Upper Assembly .......................................................... 4-27 4.10 Power Board.........................................................
4 Replacement Procedures Installing the VGA Board and VGA Thermal Module ................................ 4-41 4.19 CPU and Thermal Module ................................................................................... 4-42 Removing the CPU and Thermal Module.................................................... 4-42 Installing CPU and Thermal Module ........................................................... 4-43 4.20 Display Assembly ..................................................................
4 Replacement Procedures Figures Figure 4.1 Removing the Battery Pack ........................................................................... 4-8 Figure 4.2 Removing the HDD door ............................................................................. 4-10 Figure 4.3 Removing the HDD from the HDD bay ...................................................... 4-11 Figure 4.4 Removing the HDD plate............................................................................. 4-11 Figure 4.
4 Replacement Procedures Figure 4.32 Removing the VGA Board........................................................................... 4-40 Figure 4.33 Reapply the Shinetsu 7726 grease on the thermal module and remove any release papers .................................................................... 4-41 Figure 4.34 Removing the Thermal Module spring screws ............................................ 4-42 Figure 4.35 Removing the CPU ............................................................
4 Replacement Procedures Figure 4.60 Removing the LVDS cable from the LCD module ..................................... 4-61 Figure 4.61 Installing the LCD Hinge Assembly............................................................ 4-62 Figure 4.62 Installing the LCD Module from the LCD cover assembly (high-end model).......................................................................................... 4-63 Figure 4.63 Installing the LCD Module from the LCD cover assembly (low-end model)..........
Error! Style not defined. Error! Style not defined. 4.1 4 Replacement Procedures General This chapter explains how to disassemble the laptop and replace Field Replaceable Units (FRUs). Some replacement procedures may not require you to remove all the surrounding FRUs to replace only one FRU. The chart below shows the FRUs in the order in which they should be removed in a top-down manner, irrespective of their physical locations.
4 Replacement Procedures Error! Style not defined. Error! Style not defined. Safety Precautions Before you begin disassembly read the following safety precautions carefully. Be sure to follow them while you are working. DANGER: 1. Always use the original batteries or replacement batteries authorized by Toshiba. Batteries other than those differ in specifications and are incompatible with the laptop. They may burst or explode.
Error! Style not defined. Error! Style not defined. 4 Replacement Procedures CAUTION: 1. Before replacing a component, make sure that the replacement component meets the required specifications. To avoid laptop failures, never use components that do not meet the specifications. 2. To avoid internal damage such as short circuits and fire, never drop metal objects such as screws, pins, paper clips, etc. into the components.
4 Replacement Procedures Error! Style not defined. Error! Style not defined. Before You Begin Before you begin to disassemble the laptop, keep in mind the precautions and advice in this section. Always begin disassembly by removing the AC adapter and battery pack. Remove the optional parts and accessories as well. The procedures for removing the batteries will be explained later. Disassemble the laptop only when an abnormality has occurred. Use only the recommended tools.
Error! Style not defined. Error! Style not defined. 4 Replacement Procedures Disassembly Procedures The cable connectors come in these two basic types: Pressure plate connectors Normal pin connectors To remove a pressure plate connector, pull up the tabs on either side of the connector's plastic pressure plate and gently pull the cable out of the connector.
4 Replacement Procedures Error! Style not defined. Error! Style not defined. Tools and Equipment For your safety and that of other people in the working environment, it is strongly recommended that you use electrostatic discharge (ESD) equipment. The proper use of this equipment will ensure successful repair work and reduce the costs for repairing damaged components.
Error! Style not defined. Error! Style not defined. 4 Replacement Procedures Colors of Screw Shanks For easy identification of the correct screws, the screw shanks are colored according to their lengths, as follows: Screws of an odd-numbered length Blue Screws of a special length Black Screws of a special length are those of a length having decimal places (i.e. 16mm). Symbols of Screws on the Laptop Body For easy maintenance, the screw types are shown on the laptop body as symbols.
4 Replacement Procedures 4.2 Error! Style not defined. Error! Style not defined. Battery Removing the Battery Pack Remove the battery pack according to the following procedures and Figure 4.1. CAUTION: When handling the battery packs, use care not to short circuit the terminals. Do not drop, hit, twist, or bend the battery packs. Do not scratch or break up their casing. 1. Turn the laptop upside down so that the bottom is facing you. 2. Slide out the battery lock. 3.
Error! Style not defined. Error! Style not defined. 4 Replacement Procedures Installing the Battery Pack Install the battery pack according to the following procedures. CAUTION: The battery packs contain a lithium ion battery, which can explode due to improper replacement, use, handling or disposal. Always dispose of the battery packs as required by local ordinances or regulations. Use only replacement batteries recommended by Toshiba. NOTE: Visually check the battery's terminals.
4 Replacement Procedures 4.3 Error! Style not defined. Error! Style not defined. HDD Removing the HDD CAUTION: Do not press on the top or bottom of the drive. Applying such pressure can either corrupt the data in the drive or damage the drive. Remove the HDD (hard disk drive) according to the following procedures and Figures 4.2 and 4.3. 1. To remove the HDD, remove two M2.5x5 HDD door screws that secure the HDD and then remove the HDD door. M2.5x5*2 Figure 4.
Error! Style not defined. Error! Style not defined. 4 Replacement Procedures 2. Pull the tab right to remove the HDD module. Figure 4.3 Removing the HDD from the HDD bay NOTE: Do not disassemble the HDD pack when it is working normally. Disassemble or replace the HDD pack only if it fails. 3. Place the HDD pack on a flat surface such as a desk. 4. To separate the plate from the HDD, remove four M2.5x3 screws with torque value 3.5kgf. M2.5x3*4 Figure 4.
4 Replacement Procedures Error! Style not defined. Error! Style not defined. CAUTION: Do not apply pressure to the top or bottom of the drive. Installing the HDD Install the HDD according to the following procedures. CAUTION: To avoid damage, always hold the HDD only by its sides. 1. Place the HDD into the HDD plate. 2. Secure the HDD and its plate with four M2.5x3 screws.
Error! Style not defined. Error! Style not defined. 4.4 4 Replacement Procedures Memory Removing the Optional Memory Remove the optional memory according to the following procedures and Figure 4.5 after checking that the laptop is turned off. CAUTION: Remove the optional memory after turning off the laptop. If this is violated, the laptop or memory can be damaged. 1. Turn the laptop upside down. 2. Remove one M2.5x5 screw that secures the RAM door. 3. Remove the RAM door.
4 Replacement Procedures Error! Style not defined. Error! Style not defined. 4. Spread out the two memory lock latches so that the memory pops up. Please follow the procedure as shown in Figure 4.6. Figure 4.6 Removing the RAM from the connectors 5. Pull the memory up and out at an angle, using care to avoid touching the connectors. Installing the Optional Memory Install the optional memory according to the following procedures after checking that the laptop is turned off.
Error! Style not defined. Error! Style not defined. 4.5 4 Replacement Procedures UWB Module Removing the UWB Module Remove the UWB module according to the following procedures and Figure 4.7. 1. Detach the antenna on the UWB card. 2. Disconnect two antenna cables and remove two M2x4 screws that secure the UWB card. 3. Pull the UWB module out at an angle. M2x4*2 Figure 4.7 Removing the UWB module Installing the UWB Module Install the UWB module according to the following procedures. 1.
4 Replacement Procedures 4.6 Error! Style not defined. Error! Style not defined. Modem Card / FM Tuner Removing the Modem Card Remove the modem card according to the following procedures and Figure 4.8. 1. Remove two M2.5x3 screws that secure the modem card. 2. Flip the modem card over, and detach the cable connected to the card. M2.5x3*2 Figure 4.
Error! Style not defined. Error! Style not defined. 4 Replacement Procedures Removing the FM Tuner Remove the FM Tuner and FM jack according to the following procedures and Figure 4.9. 1. Remove two M2.5x3 screws from the FM tuner. 2. Detach the two cables from the front and back of the FM tuner. Figure 4.9 Removing the FM Tuner Installing the Modem Card Install the modem card according to the following procedures. 1. Attach the cable to the back of the modem card. 2.
4 Replacement Procedures Error! Style not defined. Error! Style not defined. Installing the FM Tuner 1. Attach the cable on the back of the FM Tuner. 2. Seat the FM Tuner in the correct position on the motherboard and attach the cable on the front of the FM Tuner to the motherboard. 3. Secure the FM Tuner to the motherboard with two M2.5x3 screws.
Error! Style not defined. Error! Style not defined. 4.7 4 Replacement Procedures ODD Removing the ODD Bay Module NOTE: The installation and removal procedures are the same for all the modules that can be installed in the ODD bay. See the appropriate sections for the disassembly procedures of specific modules. Remove the ODD bay module according to the following procedures and Figure 4.10. M2.5x6*1 Figure 4.10 Removing the ODD Bay module 1. Turn the laptop upside down. 2. Remove one M2.5x6 screw. 3.
4 Replacement Procedures Error! Style not defined. Error! Style not defined. Installing the ODD Bay Module Install the ODD bay module according to the following procedures. 1. Place the ODD bay module in the correct position and slide it in. 2. Push it in until it meets the end. 3. Secure the ODD bay module with one M2.5x6 screw. Disassembling the ODD Drive NOTE: Do not disassemble the ODD drive when it is working normally. Disassemble or replace the ODD drive only if it fails.
Error! Style not defined. Error! Style not defined. 4 Replacement Procedures Assembling the ODD Drive Assemble the ODD drive according to the following procedures. 1. Seat the bracket in the correct position. 2. Secure them with two M2×3 screws.
4 Replacement Procedures 4.8 Error! Style not defined. Error! Style not defined. Keyboard Cover and Keyboard Removing the Keyboard Cover and Keyboard Remove the Keyboard Cover and Keyboard according to the following procedures and Figures 4.12, 4.13, 4.14 and 4.15. 1. Close the laptop and turn over. Remove two M2x4 screws from inside the battery lodging. M2x4*2 Figure 4.12 Removing two screws from the battery lodging 2. Turn the laptop over and open it.
Error! Style not defined. Error! Style not defined. 4 Replacement Procedures Figure 4.13 Removing the keyboard cover 4. Remove four M2x3 screws. M2x3*4 Figure 4.
4 Replacement Procedures Error! Style not defined. Error! Style not defined. 5. Lift the keyboard up and detach the cable on the back of the keyboard from the motherboard. Figure 4.15 Removing the keyboard Installing the Keyboard Cover and Keyboard Install the keyboard cover and keyboard according to the following procedures. 1. Attach the cable on the back of the keyboard to the motherboard and place the keyboard in the correct position. 2. Secure the keyboard with four M2x3 screws. 3.
Error! Style not defined. Error! Style not defined. 4.9 4 Replacement Procedures Logic Upper Assembly Removing the Logic Upper Assembly Remove the logic upper assembly according to the following procedures and Figure 4.16, 4.17 and 4.18. 1. Turn the laptop upside down and remove the following 17 screws: Fifteen M2.5x8 screws Two M2.5x4 screws M2.5x4*2 M2.5x8*15 Figure 4.
4 Replacement Procedures Error! Style not defined. Error! Style not defined. 2. Turn to the front and remove the following screws: Five M2.5x8 screws Three M2.5x5 screws M2.5x5*3 M2.5x8*5 Figure 4.17 Removing eight screws from the laptop.
Error! Style not defined. Error! Style not defined. 4 Replacement Procedures 3. Detach eight connectors: one Power board FFC, one Control Panel FFC, two Speaker cables, one Fingerprinter FFC, one LED Board cable, one Bluetooth cable and one TouchPad cable as shown in Figure 4.18. Figure 4.18 Detaching cables from the laptop 4. Lift up the logic upper assembly. Installing the Logic Upper Assembly Install the logic upper assembly according to the following procedures. 1.
4 Replacement Procedures 4.10 Error! Style not defined. Error! Style not defined. Power Board Removing the Power Board Remove the power board according to the following procedures and Figure 4.19. 1. Remove two M2.5x4 screws from the power board. 2. Separate the power board from the logic upper assembly. M2.5x4*2 Figure 4.19 Removing the power board Installing the power switch board Install the power switch according to the following procedures. 1.
Error! Style not defined. Error! Style not defined. 4.11 4 Replacement Procedures Speakers Removing the Speakers Remove the Speakers according to the following procedures and Figure 4.20. 1. Hold the speaker in place and then remove four special M2.5x6 screws from the left and right speaker. 2. Remove the left and right speakers from the logic upper assembly. M2.5x6*4 Figure 4.20 Removing the speakers Installing the Speakers Install the speakers according to the following procedures. 1.
4 Replacement Procedures 4.12 Error! Style not defined. Error! Style not defined. Bluetooth Card Removing the Bluetooth card Remove the Bluetooth card according to the following procedures and Figure 4.21. 1. Remove the Bluetooth cable from the Bluetooth card. 2. Press down the latch and push the Bluetooth card in the direction indicated in the figure 4.21 and slide the Bluetooth card out. 3. Remove the card from the logic upper assembly. Figure 4.
Error! Style not defined. Error! Style not defined. 4.13 4 Replacement Procedures Touchpad Bracket, Touchpad Boards and Fingerprint Board Removing the Touchpad Bracket, Touchpad Boards and Fingerprint Board Remove the Touchpad bracket, Touchpad boards (the button board and switch board) and Fingerprint board according to the following procedures and Figures 4.22, 4.23. 1. Remove four M2.5x4 screws from the Touchpad bracket.
4 Replacement Procedures Error! Style not defined. Error! Style not defined. 5. Pull the Fingerprint board up to remove it from the logic upper assembly. M2.5x3*1 M2.5x4*1 Figure 4.23 Removing the Touchpad boards and Fingerprint board Installing the Touchpad Bracket, Touchpad Boards and Fingerprint Board/Touchpad Switch Board Install the Touchpad bracket, the Touchpad boards (the button and switch board) and Fingerprint board according to the following procedures. 1.
Error! Style not defined. Error! Style not defined. 4.14 4 Replacement Procedures LED board Removing the LED Board To remove the LED board from the logic lower assembly: 1. Remove one M2.5x4 screw and remove one cable from the motherboard as described in Figure 4.24 below. M2.5x4*1 Figure 4.24 Removing the LED Board Installing the LED Board Install the LED board according to the following procedure: 1. Seat the LED board on the logic lower assembly. Secure it with one M2.
4 Replacement Procedures 4.15 Error! Style not defined. Error! Style not defined. Thermal Fan Removing the Thermal Fan Remove the thermal fan according to the following procedures and Figure 4.25. 1. Detach the cable from the motherboard. 2. Remove one M2.5x8 screw from the thermal fan. Remove the thermal fan cable. 3. Remove the thermal fan from the logic lower assembly. M2.5x8*1 Figure 4.
Error! Style not defined. Error! Style not defined. 4.16 4 Replacement Procedures WLAN Card Removing the WLAN Card Remove the WLAN Card according to the following procedures and Figure 4.26. 1. Remove two M2x4 screws from the WLAN Card. 2. Remove the WLAN Card from the motherboard. M2x4*2 Figure 4.26 Removing the WLAN Card Installing the WLAN card Install the WLAN card according to the following procedures. 1. Insert the WLAN card into the connector on the motherboard. 2.
4 Replacement Procedures 4.17 Error! Style not defined. Error! Style not defined. Motherboard Removing the Motherboard Remove the motherboard according to the following procedures. 1. Remove one M2.5x4 screw and five cables from the logic lower assembly as indicated by arrows in Figure 4.27. M2.5x4*1 Figure 4.
Error! Style not defined. Error! Style not defined. 4 Replacement Procedures 2. Remove the DC_IN CONN and cable out of the logic lower assembly from right to left, as shown in Figure 4.28. Figure 4.28 Removing the DC_IN CONN and cable 3. Use left hand to hold down the lower part of the motherboard and right hand to pick the motherboard up as shown in figure 4.29. Figure 4.29 Picking up the motherboard 4. Remove the motherboard from the logic lower assembly.
4 Replacement Procedures Error! Style not defined. Error! Style not defined. Installing the Motherboard Install the motherboard according to the following procedures. 1. Before seating the motherboard on the logic lower assembly, pull out the Left USB cable and LDVS cable to avoid being pressed. 2. Align the DP CONN, S/PDIF CONN, Audio CONN and RJ45 CONN to the holes in the logic lower assembly as shown in Figure 4.30. Figure 4.
Error! Style not defined. Error! Style not defined. 4 Replacement Procedures 3. Put the DC_IN CONN in the lower DC_IN trough and route the cable from left to right under the cable-fixed Rib as shown in Figure 4.31. Figure 4.31 Installing the DC-in jack 4. Secure one M2.5x4 screw. 5. Attach five cables to the motherboard as indicated by arrows in Figure 4.27.
4 Replacement Procedures 4.18 Error! Style not defined. Error! Style not defined. VGA Board and VGA Thermal Module (Optional) Removing the VGA Board and VGA Thermal Module Remove the VGA board and thermal module according to the following procedures and Figures 4.32, 4.33. CAUTION: When removing the VGA board and VGA thermal module, keep the following in mind: 1. The unit can become very hot during operation. Be sure to let it cool down before starting the repair work. 2.
Error! Style not defined. Error! Style not defined. 4 Replacement Procedures Installing the VGA Board and VGA Thermal Module Install the VGA board and thermal Module according to the following procedures. 1. Reapply Shinetsu 7762 grease on the VGA thermal module as shown in Figure 4.33. If you use one new VGA thermal module, remove the release papers on the thermal pads first. Thermal Grease Thermal Pad Figure 4.33 Reapply the Shinetsu 7726 grease on the thermal module and remove any release papers 2.
4 Replacement Procedures 4.19 Error! Style not defined. Error! Style not defined. CPU and Thermal Module Removing the CPU and Thermal Module Remove the CPU and the CPU thermal module according to the following procedures and Figures 4.34, 4.35. CAUTION: When removing the thermal module, keep the following in mind: 1. The thermal module can become very hot during operation. Be sure to let it cool down before starting the repair work. 2.
Error! Style not defined. Error! Style not defined. 4 Replacement Procedures CAUTION: When removing the CPU, keep the following in mind: The CPU can become very hot during operation. Be sure to let it cool down before starting repair work. 3. Unlock the CPU by rotating the cam on the CPU socket counterclockwise to the unlock position with a flat-blade screwdriver. 1 2 Figure 4.35 Removing the CPU 4. Remove the CPU.
4 Replacement Procedures Error! Style not defined. Error! Style not defined. CAUTION: When installing the thermal module, keep the following in mind: 1. Be sure to confirm the correct position for the module. 2. Secure the relevant screws on the motherboard according to the number sequence sealed on the thermal module. 4. Reapply Shinetsu 7762 grease on the CPU thermal module as shown in Figure 4.36. If you use one new CPU thermal module, remove the release papers on the thermal pads first.
Error! Style not defined. Error! Style not defined. 4.20 4 Replacement Procedures Display Assembly Removing the Display Assembly CAUTION: Use care to avoid the antenna cable being caught between the display assembly and the laptop. Remove the display assembly according to the following procedures and Figure 4.37. 1. Remove six M2.5x6 screws securing the display assembly to the laptop. M2.5x6*6 Figure 4.37 Removing the display assembly 2. Remove the display assembly.
4 Replacement Procedures 4.21 Error! Style not defined. Error! Style not defined. LCD Bezel Assembly Removing the LCD Bezel Assembly The LCD comes in two different models: a high-end assembly model and a low-end assembly model. Remove the LCD bezel assembly of each model according to the following procedures. For Low-end Model 1. Remove four screw rubbers on the LCD bezel. Remove four M2.5x6 screws as shown in Figure 4.38. M2.5x6*4 Figure 4.
Error! Style not defined. Error! Style not defined. 4 Replacement Procedures 2. Peel off the bezel from left and right side as shown in Figure 4.39. Figure 4.39 Peel off the bezel 3. Pull out the bezel hinge wall from the cover hinge wall as shown in Figure 4.40. Figure 4.40 Pull out the hinge wall 4. Pull apart the lower half of the bezel; leave this portion above the L/R LCD hinge.
4 Replacement Procedures Error! Style not defined. Error! Style not defined. 5. Push the bezel from the left and right side as shown in Figure 4.41 and remove the bezel from the display assembly. Figure 4.41 Remove the bezel For High-end Model 1. For the high-end model, remove two screw rubbers on the LCD bezel and remove two M2.5x6 screws as shown in Figure 4.42. M2.5x6 M2.5x6 Figure 4.
Error! Style not defined. Error! Style not defined. 4 Replacement Procedures 2. Wrap the flat blade screwdriver with three layers of tape. Figure 4.43 Wrap the flat blade screwdriver with tape 3. Press the bezel hinge wall and cover hinge wall as indicated in Figure 4.44. Figure 4.
4 Replacement Procedures Error! Style not defined. Error! Style not defined. 4. When pressing the hinge wall, use the flat blade screwdriver to pry up the bezel hinge wall as indicated in Figure 4.45 to release the first hook on the right side. Figure 4.45 Pry up the bezel hinge wall 5. Use both hands to release the rest of the hooks as indicated in Figure 4.46. Figure 4.
Error! Style not defined. Error! Style not defined. 4 Replacement Procedures 6. Hold the hinge wall with your left hand, and push the right side of the bezel upward with right hand thumb as indicated in Figure 4.47. Figure 4.
4 Replacement Procedures Error! Style not defined. Error! Style not defined. 7. Hold the hinge wall with your right hand, and push the left side of the bezel upward with left hand thumb as indicated in Figure 4.48. Figure 4.
Error! Style not defined. Error! Style not defined. 4 Replacement Procedures 8. Release the hooks from the bottom left and bottom right of the bezel with the wrapped screwdriver as shown in Figure 4.49. Figure 4.49 Release hooks from the bottom of the bezel 9. Release the hooks on the right side of the bezel with the wrapped screwdriver as indicated in Figure 4.50. Do the same procedure for the left side. Figure 4.
4 Replacement Procedures Error! Style not defined. Error! Style not defined. 10. Release the hooks on the upper side of the bezel from left to right with the wrapped screwdriver as indicated in figure 4.51. Figure 4.51 Release the hooks from the upper side of the bezel 11.
Error! Style not defined. Error! Style not defined. 4 Replacement Procedures Installing the Display Mask Install the LCD bezel assembly according to the following procedures. 1. Seat the LCD bezel assembly in the correct position. 2. For the low-end model, press the bezel hinge wall against the cover hinge wall as shown in Figure 4.52. For the high-end model, press on the bezel hinge wall to fasten the hooks to the cover hinge wall. Figure 4.52 Press the bezel hinge wall 3.
4 Replacement Procedures Error! Style not defined. Error! Style not defined. 4. For the low-end model, press the left and right side of the bezel as shown in Figure 4.54. For the high-end model, press and secure the hooks on the left and right side of the bezel. Figure 4.54 Press the left and right side of the bezel for the low-end model/ Press the hooks on the left and right side of the bezel for the high-end model 5. Press the bezel upside hooks as shown in Figure 4.55. Figure 4.
Error! Style not defined. Error! Style not defined. 4.22 4 Replacement Procedures LCD Module and Inverter Board Removing the LCD Module and Inverter Board Remove the LCD module and the inverter board according to the following procedures and Figures 4.56, 4.57, 4.58, 4.59 and 4.60. 1. Remove one M2x3 screw securing the inverter board and detach two cables connected to the two ends of the inverter. Then remove the inverter board. M2x3 Figure 4.
4 Replacement Procedures Error! Style not defined. Error! Style not defined. 2. a. For the high-end model, remove eight M2.5x4 screws securing the LCD module according to the sequence indicated in the Figure 4.57. 1 4 M2.5x4*8 3 2 1 2 3 4 Figure 4.
Error! Style not defined. Error! Style not defined. 4 Replacement Procedures b. For the low-end model, remove six M2.5x4 screws securing the LCD module according to the sequence indicated in the Figure 4.58. 3 M2.5x4*6 1 2 1 2 3 Figure 4.58 Removing the LCD Module from the LCD cover assembly (low-end model) 3. Lift the LCD module out of the LCD cover assembly.
4 Replacement Procedures Error! Style not defined. Error! Style not defined. 4. Remove six M2x3 screws according to the sequence indicated in the Figure 4.59, and then remove the LCD hinge assembly. M2x3*6 2 2 1 1 3 3 Figure 4.59 Removing the LCD Hinge Assembly 5. Turn the LCD module over and place it face down on a protective surface, such as a foam pad.
Error! Style not defined. Error! Style not defined. 4 Replacement Procedures 6. Remove the tape and LVDS cable connector. Then detach the LVDS cable. Figure 4.60 Removing the LVDS cable from the LCD module NOTE: Integrated Circuits (ICs) are fragile. Use extreme care not to apply pressure to the ICs along the edges of the LCD module. Dispose of used LCD panels (fluorescent (FL) tubes) as required by local ordinances or regulations.
4 Replacement Procedures Error! Style not defined. Error! Style not defined. Installing the LCD Module and Inverter Board Install the inverter board according to the following procedures. 1. Turn the LCD module cover and place it face down on a protective surface such as a foam pad. 2. Connect the LVDS cable to the LCD panel connector. 3. Turn the LCD right side up. 4.
Error! Style not defined. Error! Style not defined. 4 Replacement Procedures 5. Seat the LCD module in the correct position in the LCD cover assembly. Secure it to the LCD cover assembly with eight M2.5x4 screws for the high-end model, or with six M2.5x4 screws for the low-end model, according to the sequence indicated in Figure 4.62 and Figure 4.63. Reroute the CMOS and Antenna cables after securing the LCD panel. 4 1 M2.5x4*8 2 3 4 3 2 1 Figure 4.
4 Replacement Procedures Error! Style not defined. Error! Style not defined. 1 M2.5x4*6 3 2 3 2 1 Figure 4.63 Installing the LCD Module from the LCD cover assembly (low-end model) 6. Seat the inverter board in correct position and connect two cables to the two ends of the inverter board. Then secure it with one M2x3 screw.
Error! Style not defined. Error! Style not defined. 4 Replacement Procedures NOTE: Be careful not to pinch codes beside hinges. Figure 4.64 Not to pinch codes beside hinges (high-end model) Figure 4.
4 Replacement Procedures 4.23 Error! Style not defined. Error! Style not defined. CMOS Board and MIC Removing the CMOS Board and MIC Remove the CMOS Board and MIC according to the following procedures and Figure 4.66 and 4.67. 1. Disconnect the CMOS cable from the CMOS module connector and remove the CMOS board. Figure 4.
Error! Style not defined. Error! Style not defined. 4 Replacement Procedures Figure 4.67 Removing the CMOS board and MIC (low-end model) 2. Lift the MIC cable from the LCD cover assembly. Installing the CMOS Board and MIC Install the CMOS Board and MIC according to the following procedures. 1. Connect the CMOS module cable to CMOS module connector. 2. Seat the CMOS module and MIC in the correct position on the LCD cover assembly. 3. Fix the CMOS cable and MIC cable with tapes.
4 Replacement Procedures 4.24 Error! Style not defined. Error! Style not defined. Left USB Board Removing the USB Board on the Left Side Remove the left USB board according to the following procedures and Figure 4.68. 1. Remove the USB board from the left side of the logic lower assembly using one M2.5x4 screw. M2.5x4 Figure 4.68 Removing the left USB Board from the logic lower assembly Installing the Left USB Board Install the left USB board according to the following procedures. 1.
Error! Style not defined. Error! Style not defined. 4.25 4 Replacement Procedures Right USB Board Removing the Right USB Board on the Right Side Remove the Right USB board according to the following procedures and Figure 4.69. 1. Wrap a flat balde screwdriver with three layers of tape. Figure 4.69 Wrap the flat blade screwdriver with tape 2. Disconnect the FFC cable from the motherboard.
4 Replacement Procedures Error! Style not defined. Error! Style not defined. 3. Tear the FFC cable up from the logic lower assembly. Figure 4.70 Wrap the flat blade screwdriver with tape 4. Pry up the right USB Board from the right side with a flat blade screwdriver wrapped with three layers of tape. Be careful not to scratch the FFC cable. Figure 4.
Error! Style not defined. Error! Style not defined. 4 Replacement Procedures Installing the Right USB Board Install the Right USB board according to the following procedures. 1. Seat the USB board in the correct position on the right side of the logic lower assembly. 2. Secure the USB board to the logic lower assembly with one M2.5x4 screw. 3. Secure the USB board to the logic lower assembly with one M2.5x4 screw and connect the FFC cable to the Motherboard.
Appendix A Appendix A Handling the LCD Module Precautions for handling the LCD module The LCD module can be easily damaged during assembly or disassembly. Observe the following precautions when handling it to prevent damaging it. 1. When installing the LCD module in the display assembly, make sure that you seat it so that it is properly aligned and maximum visibility of the display is maintained. 2.
3. If the panel’s surface gets dirty or moist, wipe it with cotton or a soft cloth. If it is still dirty, try breathing on the surface to create a light condensate and wipe it again. If the surface is very dirty, we recommend a CRT cleaning agent. Apply the agent to a soft cloth and then wipe the panel’s surface. Do not apply cleanser directly to the panel. CRT Cleaner 4. If water or other liquid is left on the panel’s surface for a long period, it can change the screen’s tint or stain it.
5. Glass is used in the panel, so be careful not to drop it or let it strike a hard object, which could cause breakage or cracks. 6. CMOS-LSI circuits are used in the module, so guard against damage from electrostatic discharge. Be sure to wear a wrist or ankle grounding device when handling the module.
7. Do not expose the module to direct sunlight or strong ultraviolet rays for long periods. 8. Do not store the module at temperatures below its specifications. Cold can cause the liquid crystals to freeze, lose their elasticity or otherwise suffer damage. 9. Do not disassemble the LCD module. Disassembly can cause malfunctions.
10. If you transport the module, do not use packing material that contains epoxy resin (amine) or silicon glue (alcohol or oxime). These materials can release gas that can damage the panel’s polarization.
Appendix B Appendix B Board Layout B.
B.
Number Name U3 North bridge AMD RS780/RX781 U10 Clock Generator SLG8SP626VTR U15 South bridge AMD SB700 U33 KB926QFD3(EC) U46 BIOS ROM UA2 ALC272-GR UC1 JMB385(CARD READ) UL1 RTL8111DL U54 G-sensor Table B-2 System Board Connectors (top and bottom) Number Name JCPU CPU Socket JFAN Fan conn. JDDRH, JDDRL DDRII conn. JCRT CRT conn. JBCAS1 B-CAS conn JBLG KEYBOARD Back Light conn JREAD 5 in 1 Card Reader conn. JMIC Microphone conn. JSPKR, JSPKL Speaker conn.
B-4 JLED LED/B conn. JCS CapSensor/B conn. JFM FMTuner/B conn. JESATA eSATA conn. JHDMI HDMI conn JLAN LAN conn. JLINE Headphones conn. JEXMIC External MIC conn. JLIGHT Light Pipe conn JLVDS LVDS conn. JLINE HeadPhone/LINE Out JACK conn JGPS GPS conn. JMDC MDC conn JMXM MXM conn JNAND WUSB or Upconvert conn JSSD SSD conn JUSBB1 LEFT USB JUSBB2 Right USB PJP1 AC Adaptor conn. PJP2 Battery conn.
C. Appendix C Pin Assignments System Board C.1 JFAN Table C-1 FAN I/F pin assignments (3-pin) Pin No. C.2 Signal name 1 +FAN1 3 GND I/O Pin No. Signal Name 2 FAN_SPEED1 I/O JFM Table C-2 FM I/F pin assignments (10-pin) Pin No. C.3 Signal name I/O Pin No. Signal Name 1 +3VS 2 +3VS 3 FM_I2CCLK 4 FM_I2CDAT 5 FM_I2C_INT# 6 FM_OUTR 7 FM_OUTL 8 GND 9 GND 10 GND I/O JLVDS Table C-3 LVDS I/F pin assignments (40-pin) Pin No. Signal name I/O Pin No.
C.4 17 LCD_TZCLK- 19 GND 21 LCD_EDID_CLK 23 LCD_EDID_DATA 25 O 18 LCD_TXOUT1- O 20 LCD_TXOUT2+ O O 22 LCD_TXOUT2- O O 24 GND O +LCDVDD_R 26 LCD_TZOUT0+ O 27 +LCDVDD_R 28 LCD_TZOUT0- O 29 +3VS 30 LCD_TZOUT1+ O 31 NA 32 LCD_TZOUT1- O 33 +LCD_INV 34 LCD_TZOUT2+ O 35 +LCD_INV 36 LCD_TZOUT2- O 37 +LCD_INV 38 GND 39 +LCD_INV 40 BKOFF# O JCRT Table C-4 CRT pin assignments (15-pin) Pin No. C.5 Signal name I/O Pin No.
C.6 11 GND 13 HDMI_CEC 15 HDMI_SCLK 17 GND 19 HDMI_HPD 12 HDMI_R_CK- O O 14 NC O 16 HDMI_SDATA O 18 +HDMI_5V_OUT O O JHDD0 Table C-6 1st HDD I/F pin assignments (22-pin) Pin No. C.7 Signal name I/O Pin No.
C.8 JESATA Table C-8 1st eSATA/USB I/F pin assignments (11-pin) Pin No. C.9 Signal name I/O Pin No. Signal Name 1 +USB_VCCB 2 USB20_N2_R_ S 3 USB20_P2_R_ S 4 GND 5 GND 6 SATA_C_TX2+ 7 SATA_C_TX2- 8 GND 9 SATA_C_RX2- 10 SATA_C_RX2+ 11 GND I/O JBT Table C-9 Bluetooth Connector pin assignments (10-pin) Pin No. Signal name Pin No. Signal Name 1 GND 2 +3VS 3 +BT_VCC 4 WLAN_BT_DATA 5 BT_RST# 6 BT_DET# 7 WLAN_BT_CLK 8 USB20_N6 9 USB20_P6 10 GND I/O C.
Pin No. Signal name 1 +CAM_VDD 3 USB20_P9_R 5 GND I/O I/O Pin No. Signal Name 2 USB20_N9_R 4 GND I/O I/O C.12 JWLAN Table C-12 Wi-Fi/WiMax Connector pin assignments (52-pin) Pin No. Signal name I/O Pin No. Signal Name 1 NC 2 +3VS 3 WLAN_BT_DATA 4 GND 5 WLAN_BT_CLK 6 +1.
C.13 JEXP Table C-13 New Card Connector pin assignments (26-pin) Pin No. Signal name I/O Pin No. Signal Name 1 GND 2 USB20_N5 3 USB20_P5 4 CP_USB# 5 NC 6 NC 7 SMB_CK_CLK0 8 SMB_CK_DAT0 9 +1.5VS_CARD 10 +1.5VS_CARD 11 EC_SWI#_R 12 +3VALW_CARD 13 PERST# 14 +3VS_CARD 15 +3VS_CARD 16 CLKREQ# 17 EXP_CPPE# 18 CLK_PCIE_NCARD# 19 CLK_PCIE_NCARD 20 GND 21 PCIE_PTX_C_IRX_N0 22 PCIE_PTX_C_IRX_P0 23 GND 24 PCIE_ITX_C_PRX_N0 25 PCIE_ITX_C_PRX_P0 26 GND I/O C.
1 +5VALW 2 +5VS 3 DC_IN 4 POWER_LED 5 SUSPEND_LED 6 HDD_LED 7 CR_LEDCON 8 BATT_FULL_LED# 9 BATT_LOW_LED# 10 GND 11 GND 12 GND C.16 JGPS Table C-16 GPS Connector pin assignments (52-pin) Pin No. Signal name I/O Pin No. Signal Name 1 NC 2 +3VS 3 XBCLKM 4 GND 5 BCCDET 6 +1.
51 NC 52 +3VS C.17 JDDRL, JPDDRH Table C-17 SODIMM I/F pin assignments (200-PIN) (1/4) Pin No. Signal name I/O Pin No.
53 VSS O 54 VSS O 55 DQ18 I/O 56 DQ22 I/O 57 DQ19 I/O 58 DQ23 I/O 59 VSS O 60 VSS O 61 DQ24 I/O 62 DQ28 I/O 63 DQ25 I/O 64 DQ29 I/O 65 VSS O 66 VSS O 67 DM3 I/O 68 DQS3# I/O 69 NC - 70 DQS3 I/O 71 VSS O 72 VSS O 73 DQ26 I/O 74 DQ30 I/O 75 DQ27 I/O 76 DQ31 I/O 77 VSS O 78 VSS O 79 CKE0 I/O 80 NC/CKE1 I/O 81 VDD O 82 VDD O 83 NC - 84 NC/A15 - 85 BA2 I/O 86 NC/A14 - 87 VDD O 88 VDD O 89 A12 I/O 90 A1
117 VDD O 118 VDD O 119 NC/ODT1 I/O 120 NC - 121 VSS O 122 VSS O 123 DQ32 I/O 124 DQ36 I/O 125 DQ33 I/O 126 DQ37 I/O 127 VSS O 128 VSS O 129 DQS4# I/O 130 DM4 I/O 131 DQS4 I/O 132 VSS O 133 VSS O 134 DQ38 I/O 135 DQ34 I/O 136 DQ39 I/O 137 DQ35 I/O 138 VSS O 139 VSS O 140 DQ44 I/O 141 DQ40 I/O 142 DQ45 I/O 143 DQ41 I/O 144 VSS O 145 VSS O 146 DQS5# I/O 147 DM5 I/O 148 DQS5 I/O 149 VSS O 150 VSS O 151 DQ42
181 DQ57 I/O 182 DQ61 I/O 183 VSS I/O 184 VSS I/O 185 DM7 O 186 DQS7# O 187 VSS I/O 188 DQS7 I/O 189 DQ58 O 190 VSS O 191 DQ59 - 192 DQ62 - 193 VSS I/O 194 DQ63 - 195 SDA O 196 VSS O 197 SCL I/O 198 SA0 I/O 199 VDDSPD I/O 200 SA1 I/O C.18 JMIC Table C-18 Internal Microphone Connector pin assignments (2-pin) Pin No. 1 Signal name I/O INT_MIC Pin No. 2 Signal Name I/O GND C.
3 CAPS_LED# 4 +3VS 5 KSI1 6 KSI6 7 KSI5 8 KSI0 9 KSI4 10 KSI3 11 KSI2 12 KSI7 13 KSO15 14 KSO12 15 KSO11 16 KSO10 17 KSO9 18 KSO8 19 KSO13 20 KSO7 21 KSO6 22 KSO14 23 KSO5 24 KSO3 25 KSO4 26 KSO0 27 KSO1 28 KSO2 29 NC 30 NC 31 KSO17 32 NC 33 KSO16 34 +3VS C.21 JCS Table C-21 FUN/B connector pin assignments (10P-pin) Pin No. Signal name I/O Pin No.
C.23 JREAD Table C-23 CARD READER connector pin assignments (40P-pin) Pin No. Signal name I/O Pin No.
5 GND C.25 JSPKL Table C-25 SPKL connector pin assignments (4P-pin) Pin No. Signal name I/O Pin No. Signal Name 1 SPK_L1 2 SPK_L2 3 NC 4 NC I/O C.26 JSPKR Table C-26 SPKR connector pin assignments (4P-pin) Pin No. Signal name I/O Pin No. Signal Name 1 SPK_R1 2 SPK_R2 3 NC 4 NC I/O C.27 JTOUCH Table C-27 T/P connector pin assignments (4P-pin) Pin No. Signal name I/O Pin No. Signal Name 1 +5VS 2 TP_CLK 3 TP_DATA 4 GND I/O C.
C.29 JBLG Table C-29 KEYBOARD BACKLIGHT connector pin assignments (4P-pin) Pin No. Signal name I/O Pin No. Signal Name 1 +5VS_LED 2 NC 3 NC 4 GND I/O C.30 JDP Table C-30 Display Port connector pin assignments (20P-pin) Pin No. Signal name I/O Pin No.
C.32 JLIGHT Table C-32 Light Pipeconnector pin assignments (4P-pin) Pin No. Signal name I/O Pin No. Signal Name 1 +5VS 2 L_LED# 3 KSI6 4 KSO0 5 GND 6 GND I/O C.33 JMDC Table C-33 MDC pin assignments (12P-pin) Pin No. Signal name I/O Pin No. Signal Name 1 GND 2 +3VALW 3 HDA_SDOUT_MDC 4 NC 5 GND 6 +3VALW 7 HDA_SYNC_MDC 8 GND 9 HDA_SDIN1 10 GND 11 HDA_RST#_MDC 12 HDA_BITCLK_MDC I/O C.34 JMXM Table C-34 MXM pin assignments (230-PIN) Pin No.
13 +MXM_B+ 14 +1.
C-18 83 GND 84 PCIE_MTX_C_GRX_P6 85 PCIE_GTX_C_MRX_N5 86 GND 87 PCIE_GTX_C_MRX_P5 88 PCIE_MTX_C_GRX_N5 89 GND 90 PCIE_MTX_C_GRX_P5 91 PCIE_GTX_C_MRX_N4 92 GND 93 PCIE_GTX_C_MRX_P4 94 PCIE_MTX_C_GRX_N4 95 GND 96 PCIE_MTX_C_GRX_P4 97 PCIE_GTX_C_MRX_N3 98 GND 99 PCIE_GTX_C_MRX_P3 100 PCIE_MTX_C_GRX_N3 101 GND 102 PCIE_MTX_C_GRX_P3 103 PCIE_GTX_C_MRX_N2 104 GND 105 PCIE_GTX_C_MRX_P2 106 PCIE_MTX_C_GRX_N2 107 GND 108 PCIE_MTX_C_GRX_P2 109 PCIE_GTX_C_MRX_N1 1
151 GND 152 GND 153 NC 154 NC 155 NC 156 NC 157 NC 158 VGA_SPDIF 159 VGA_AUXN 160 VGA_LCD_TZOUT2- 161 VGA_AUXP 162 VGA_LCD_TZOUT2+ 163 GND 164 GND 165 NC 166 VGA_LCD_TZOUT1- 167 NC 168 VGA_LCD_TZOUT1+ 169 GND 170 GND 171 NC 172 VGA_LCD_TZOUT0- 173 NC 174 VGA_LCD_TZOUT0+ 175 GND 176 GND 177 VGA_DP3- 178 VGA_LCD_TXCLK- 179 VGA_DP3+ 180 VGA_LCD_TXCLK+ 181 DP_HPD 182 GND 183 NC 184 NC 185 NC 186 NC 187 GND 188 GND 189 VGA_DP0- 190 VG
219 VGA_HDMI_TXD1- 220 VGA_HDMI_CLK 221 VGA_HDMI_TXD1+ 222 NC 223 GND 224 GND 225 VGA_HDMI_TXD0- 226 +3VS_MXM 227 VGA_HDMI_TXD0+ 228 +3VS_MXM 229 GND 230 +3VS_MXM C.35 JNAND Table C-35 NAND pin assignments (52-PIN) Pin No. Signal name 1 C-20 Pin No. Signal Name NC 2 +3VS 3 NC 4 GND 5 NC 6 +1.
49 NC 50 GND 51 NC 52 +3VS C.36 JSSD Table C-36 SSD pin assignments (16-PIN) Pin No. Signal name 1 I/O Pin No. Signal Name GND 2 SATA_C_TX0+ 3 SATA_C_TX0- 4 GND 5 SATA_C_RX0- 6 SATA_C_RX0+ 7 GND 8 +3VS 9 +3VS 10 GND 11 GND 12 NC 13 NC 14 NC 15 NC 16 NC I/O C.37 JUSBB1 Table C-37 USB LEFT pin assignments (6-PIN) Pin No. Signal name 1 I/O Pin No. Signal Name +USB_VCCC 2 +USB_VCCC 3 USB20_N4_R 4 USB20_P4_R 5 GND 6 GND I/O C.
11 C-22 USB20_P1_R [CONFIDENTIAL] 12 GND SatelliteA500D/ProA500D Maintenance Manual
Appendix D Appendix D Keyboard Scan/Character Codes Table D-1 Scan codes (set 1 and set 2) (1/4) Cap No.
Table D-1 Scan codes (set 1 and set 2) (2/4) D-2 Cap No.
Table D-1 Scan codes (set 1 and set 2) (3/4) Cap No.
Table D-1 Scan codes (set 1 and set 2) (4/4) Cap No. Keytop Code set 1 122 F11 57 D7 78 F0 78 *3 123 F12 58 D8 07 F0 07 *3 124 PrintSc *6 *6 *6 *6 *6 126 Pause *7 *7 *7 *7 *7 X Fn — — — — *4 X Win E0 5B E0 DB E0 1F E0 F0 1F x App E0 5D E0 DD E0 2F E0 F0 2F Make Code set 2 Break Make Note Break Notes: 1. 2. 3. 4. 5. 6. 7. D-4 * * * * * * * Scan codes differ by mode. Scan codes differ by overlay function.
Table D-2 Scan codes with left Shift key Cap Key Code set 1 No.
Table D-3 Scan codes in Numlock mode Cap Key Code set 1 No.
Table D-5 Scan codes in overlay mode Cap No. Code set 1 Keytop Code set 2 Make Break Make Break 09 8 (8) 48 C8 75 F0 75 10 9 (9) 49 C9 7D F0 7D 11 0 (*) 37 B7 7C F0 7C 23 U (4) 4B CB 6B F0 6B 24 I (5) 4C CC 73 F0 73 25 O (6) 4D CD 74 F0 74 26 P (–) 4A CA 7B F0 7B 37 J (1) 4F CF 69 F0 69 38 K (2) 50 D0 72 F0 72 39 L (3) 51 D1 7A F0 7A 40 ; (+) 4E CE 79 F0 79 52 M (0) 52 D2 70 F0 70 54 . (.
Table D-7 No.126 key scan code Key top Pause Shift Code set 1 Code set 2 Make Make Common E1 1D 45 E1 Ctrl E0 46 E0 C6 9D C5 E1 14 77 E1 F0 E0 7E E0 F0 7E 14 F0 77 *: This key generates only make codes.
Appendix E Key Layout 1. United Status (US) Keyboard Figure US keyboard 2. Traditional Chinese (CH) Keyboard Figure CH keyboard 3.
Figure TI keyboard 4. Korean (KO) Keyboard Figure KO keyboard 5.
Figure UK keyboard 6. US International (UI) Keyboard Figure UI keyboard 7.
Figure HB keyboard 8. Danish (DM) Keyboard Figure DM keyboard 9.
Figure SW keyboard 10. Arabic (ARE) Keyboard Figure ARE keyboard 11.
Figure CZ keyboard 12. Russian (RU) Keyboard Figure RU keyboard 13.
Figure PO keyboard 14. Slovakian (SL) Keyboard Figure SL keyboard 15.
Figure IT keyboard 16. French (FR) Keyboard Figure FR keyboard 17.
Figure GR keyboard 18. Greek (GK) Keyboard Figure GK keyboard 19.
Figure HG keyboard 20. Spanish (SP) Keyboard Figure SP keyboard 21.
Figure TR keyboard 22. Turkish F (TF-F) Keyboard Figure TF-F keyboard 23.
Figure SD keyboard 24. Belgian (BE) Keyboard Figure BE keyboard 25.
Figure YU keyboard 26. Norwegian (NW) Keyboard Figure NW keyboard 27.
Figure ND keyboard 28. Canadian Multinational (AC) Keyboard Figure AC keyboard 29.
Figure CB keyboard 30. Romania (RO) Keyboard Figure RO keyboard 31.
Figure BU keyboard 32.
Torque DISCRIPTION (kg-cm) Part number Q’ty LCD PANEL TO LCD BREAKET(H/L) 1.2~1.5 MA0000060G0 6 LCD HINGE TO LCD COVER(H) 2.5~3.0 MA000007JG0 8 LCD HINGE TO LCD COVER(L) 2.5~3.0 MA000007JG0 6 LCD BEZEL TO LCD BRK TO LCD COVER(H) 2.5~3.0 MA0000062G0 2 LCD BEZEL TO LCD BRK TO LCD COVER(L) 2.5~3.0 MA0000062G0 4 INVERTER TO LCD COVER 1.5~2.0 MA0000060G0 1 ODD MODULE TO ODD BRK 1.5~2.0 MA0000060G0 2 HDD TO HDD BREAKET 2.5~3.0 MAAA03032G0 4 ODD CONN TO MB 1.5~2.
Torque (kg-cm) Part number Q’ty KEYBOARD TO LOGIC 1.5~2.0 MA0000060G0 4 KEYBOARD COVER TO LOGIC 1.5~2.0 MACA25001G0 2 SYSTEM LED BOARD TO LOGIC 2.5~3.0 MA000007JG0 1 L USB BOARD TO LOGIC 2.5~3.0 MA000007JG0 1 MB TO LOGIC 2.5~3.0 MA000005WG0 1 LOW BATTERY HOUSING TO UPPER 2.5~3.0 MA000007JG0 2 TV TUNER CABLER 2.5~3.0 MA000007JG0 1 CPU THERMAL MODULE 2.5~3.0 AM077000C00 4 VGA THERMAL MODULE 2.5~3.
Appendix G Appendix G Reliability The following table shows MTBF (Mean Time Between Failures) for each component.