® Satellite A60/A65 Series User’s Guide If you need assistance: ❖ Toshiba Global Support Centre Calling within the United States (800) 457-7777 Calling from outside the United States (949) 859-4273 For more information, see “If Something Goes Wrong” on page 165 in this guide. Handling the cord on this product will expose you to lead, a chemical known to the State of California to cause birth defects or other reproductive harm. Wash hands after handling.
Models: Satellite® A60/A65 Series ReWritable CD/DVD Drives The computer system you purchased may include a ReWritable CD and/or DVD drive(s), among the most advanced data storage technologies available. As with any new technology, you must read and follow all set-up and usage instructions in the applicable user guides and/or manuals enclosed. If you fail to do so, this product may not function properly and you may lose data or suffer other damage.
CRITICAL APPLICATION, YOU, AND NOT TOSHIBA, ASSUME FULL RESPONSIBILITY FOR SUCH USE. FCC Notice “Declaration of Conformity Information” This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
Contact: Toshiba America Information Systems, Inc. 9740 Irvine Blvd. Irvine, CA 92618-1697 (949) 583-3000 Industry Canada requirement This Class B digital apparatus complies with Canadian ICES-003. Cet appareil numérique de la classe B est conformé à la norme NMB-003 du Canada. FCC requirements The following information is pursuant to FCC CFR 47, Part 68 and refers to internal modems. This equipment complies with Part 68 of the FCC rules.
Telephone Company Procedures The goal of the telephone company is to provide you with the best service it can. In order to do this, it may occasionally be necessary for them to make changes in their equipment, operations or procedures. If these changes might affect your service or the operation of your equipment, the telephone company will give you notice, in writing, to allow you to make any changes necessary to maintain uninterrupted service.
Alarm Equipment If your home has specially wired alarm equipment connected to the telephone line, ensure the installation of this equipment does not disable your alarm equipment. If you have questions about what will disable alarm equipment, consult your telephone company or a qualified installer. Instructions for IC CS-03 Certified Equipment 1 NOTICE: The Industry Canada label identifies certified equipment.
NOTICE: The Ringer Equivalence Number (REN) assigned to each terminal device provides an indication of the maximum number of terminals allowed to be connected to a telephone interface. The termination on an interface may consist of any combination of devices subject only to the requirement that the sum of the Ringer Equivalence Numbers of all the devices does not exceed 5. 3 The standard connecting arrangement (telephone jack type) for this equipment is jack type(s): USOC RJ11C.
Wireless LAN and your Health Wireless LAN products, like other radio devices, emit radio frequency electromagnetic energy. The level of energy emitted by Wireless LAN devices however is far much less than the electromagnetic energy emitted by wireless devices like for example mobile phones. Because Wireless LAN products operate within the guidelines found in radio frequency safety standards and recommendations, TOSHIBA believes Wireless LAN is safe for use by consumers.
Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of this device.
Finnish: Dutch: French: Swedish: Danish: German: Valmistaja TOSHIBA Corp. Digital Media Network Company vakuuttaa täten että Radio LAN device tyyppinen laite on direktiivin 1999/5/EY oleellisten vaatimusten ja sitä koskevien direktiivin muiden ehtojen mukainen. Hierbij verklaart TOSHIBA Corp. Digital Media Network Company dat het toestel Radio LAN device in overeenstemming is met de essentiële eisen en de andere relevante bepalingen van richtlijn 1999/5/EG. Bij deze TOSHIBA Corp.
Spanish: Portuguese: Por medio de la presente TOSHIBA Corp. Digital Media Network Company declara que el Radio LAN device cumple con los requisitos esenciales y cualesquiera otras disposiciones aplicables o exigibles de la Directiva 1999/5/CE. TOSHIBA Corp. Digital Media Network Company declara que este Radio LAN device está conforme com os requisitos essenciais e outras disposições da Directiva 1999/5/CE. USA – Federal Communications Commission (FCC) This device complies with Part 15 of FCC Rules.
Caution: Radio Frequency Interference Requirements This device is restricted to indoor use due to its operation in the 5.15 GHz to 5.25 GHz frequency range. FCC requires this product to be used indoors for frequency range 5.15 GHz to 5.25 GHz to reduce the potential for harmful interference to co-channel Mobile Satellite systems. High power radars are allocated as primary users of the 5.25 GHz to 5.35 GHz and 5.65 GHz to 5.85 GHz bands.
2. Indication The indication shown below appears on this equipment. (1) (2) (3) 2.4DSOF4 (4) 1 2.4: This equipment uses a frequency of 2.4 GHz. 2 DS: This equipment uses DS-SS modulation. OF: This equipment uses OFDM modulation. 3 The interference range of this equipment is less than 40m. 4 This equipment uses a frequency bandwidth from 2,400 MHz to 2,483.5 MHz. It is possible to avoid the band of mobile object identification systems. 3.
Approval Number: D01-1128JP TELECOM ENGINEERING CENTER Approval Number: 03NY.A0018, 03GZDA0017 The following restrictions apply: ❖ ❖ ❖ Do not disassemble or modify the device. Do not install the embedded wireless module into other device. 5.17 GHz to 5.23 GHz for indoor use only Radio approvals for wireless devices NOTE The following information is dependent on what type of wireless device is in your computer.
Europe - Restrictions for use of 2.4 GHz Frequencies in European Community Countries België/ Belgique: Deutschland: France: Italia: Nederland: For private usage outside buildings across public grounds over less than 300m no special registration with IBPT/BIPT is required. Registration to IBPT/BIPT is required for private usage outside buildings across public grounds over more than 300m. For registration and license please contact IBPT/BIPT.
802.
❖ This device must not be operated in ad-hoc mode using channels in the 5 GHz bands in the European Community. Ad-hoc mode provides a direct communication between two client devices without a Wireless LAN Access Point. ❖ This device must be used with Access Points that have employed and activated a radar detection feature required for European Community operation in the 5 GHz bands.
802.11a (5 GHz) Australia Canada France Ireland Luxembourg Norway Switzerland Austria Denmark Germany Italy Netherlands Portugal UK Belgium Finland Greece Liechtenstein New Zealand Sweden USA Turbo Mode (5 GHz) Canada USA Approved Countries/Regions for use for the Intel® PRO/ Wireless LAN 2100 3B Mini PCI Adapter This equipment is approved to the radio standard by the countries/regions in the following table. Do not use this equipment except in the countries/regions in the following table.
Approved Countries/Regions for use for the Toshiba Mini PCI Wireless LAN Card This equipment is approved to the radio standard by the countries/regions in the following table. Do not use this equipment except in the countries/regions in the following table.
Bluetooth wireless technology is a new innovative technology, and TOSHIBA has not confirmed compatibility of its Bluetooth™ products with all PCs and/ or equipment using Bluetooth wireless technology other than TOSHIBA portable computers. Always use Bluetooth™ cards from TOSHIBA in order to enable wireless networks over two or more (up to a total of seven) TOSHIBA portable computers using these cards. Please contact TOSHIBA PC product support on Web site http://www.toshiba-europe.
community and result from deliberations of panels and committees of scientists who continually review and interpret the extensive research literature. In some situations or environments, the use of Bluetooth wireless technology may be restricted by the proprietor of the building or responsible representatives of the organization.
Caution: FCC Interference Statement This device complies with part15 of the FCC rules. Operation is subject to the following two conditions: ❖ This device may not cause harmful interference, and ❖ This device must accept any interference received, including interference that may cause undesired operation. Note that any changes or modifications to this equipment not expressly approved by the manufacturer may void the authorization to operate this equipment.
Article 17 Any use of low power radio frequency electric machinery shall not affect the aviation safety and interfere with legal communications. In event that any interference is found, the use of such electric machinery shall be stopped immediately, and reusing of such products can be resumed until no interference occurs after improvement. The legal communications mentioned in the above item refer to radio communications operated in accordance with telecommunication laws and regulations.
3 The interference range of this equipment is less than 10m. 4 This equipment uses a frequency bandwidth from 2,400 MHz to 2,483.5 MHz. It is impossible to avoid the band of mobile object identification systems. 3.
Location of the required label (Sample shown below. Location of the label and manufacturing information may vary.) This appliance contains a laser system and is classified as a “CLASS 1 LASER PRODUCT.” To use this model properly, read the user’s guide carefully and keep it for your future reference. In case of any trouble with this model, please contact your nearest “AUTHORIZED service station.” To prevent direct exposure to the laser beam, do not try to open the enclosure.
Notice The information contained in this manual, including but not limited to any product specifications, is subject to change without notice. TOSHIBA CORPORATION AND TOSHIBA AMERICA INFORMATION SYSTEMS, INC. (TOSHIBA) PROVIDES NO WARRANTY WITH REGARD TO THIS MANUAL OR ANY OTHER INFORMATION CONTAINED HEREIN AND HEREBY EXPRESSLY DISCLAIMS ANY IMPLIED WARRANTIES OF MERCHANTABILITY OR FITNESS FOR ANY PARTICULAR PURPOSE WITH REGARD TO ANY OF THE FOREGOING.
Computer disposal information This product contains mercury. Disposal of this material may be regulated due to environmental considerations. For disposal, reuse or recycling information, please contact your local government or the Electronic Industries Alliance at www.eiae.org. 5.375 x 8.375 ver 2.
Contents Introduction ..............................................................35 This guide .............................................................. 36 Safety icons ........................................................... 36 Other icons used.............................................. 37 Other documentation ............................................. 38 Service options ...................................................... 38 Chapter 1: Getting Started....................................
Contents 29 Using the computer for the first time ..................... 52 Opening the display panel ................................ 52 Your computer’s features and specifications.... 53 Turning on the power....................................... 53 Activating the power-on password................... 54 Using the TouchPad™ ............................................ 55 Using TOSHIBA Touch and Launch.................. 58 Installing additional memory (optional) .................
Contents Windows® special keys .................................... 82 Overlay keys..................................................... 83 Starting a program................................................. 84 Starting a program from the Start menu.......... 85 Starting a program from Windows ® Explorer... 85 Starting a program from the Run dialog box ... 86 Saving your work ................................................... 88 Printing your work .................................................
Contents 31 Starting again from Hibernation mode ........... 112 Using Standby ..................................................... 112 Going into Standby mode more quickly ......... 113 Starting again from Standby .......................... 115 Toshiba’s online resources................................... 115 Chapter 3: Mobile Computing ................................. 116 Toshiba’s energy-saver design ............................. 116 Running the computer on battery power .............
Contents Connecting the modem to a telephone line .... 138 Connecting your computer to a network ....... 138 An overview of using the Internet ........................ 140 The Internet ................................................... 140 The World Wide Web .................................... 141 Internet Service Providers.............................. 141 Connecting to the Internet ............................ 141 Surfing the Internet........................................ 142 Internet features...
Contents 33 Hotkey utility ........................................................ 157 TOSHIBA Console ................................................ 157 Customize Your Computer ............................. 159 Security.......................................................... 159 Power Management ....................................... 159 Toshiba Hardware Setup ................................ 161 TOSHIBA Zooming Utility..................................... 163 Application Launch Button ............
Contents Contacting Toshiba ........................................ 194 Other Toshiba Internet Web sites ........................ 195 Toshiba’s worldwide offices ................................. 195 Appendix A: Hot Keys ............................................. 197 Volume Mute........................................................ 197 Instant password security.................................... 197 Without a password ....................................... 197 With a password .................
Introduction Welcome to the world of powerful and portable multimedia computers! With your new Toshiba notebook computer, your access to information can accompany you wherever you go. Your system comes the Microsoft® Windows® XP Home or XP Pro operating system. Your operating system offers exciting features and easy Internet access. This guide contains information about your operating system and how it functions with your Toshiba computer.
Introduction This guide NOTE The product specifications and configuration information are designed for a product Series. Your particular model may not have all the features and specifications listed or illustrated. For more detailed information about the features and specifications on your particular model, please visit Toshiba's Web site at pcsupport.toshiba.com.
Introduction Safety icons 37 the seriousness of the risk, and the icons highlight these instructions as follows: Indicates an imminently hazardous situation which, if not avoided, will result in death or serious injury. Indicates a potentially hazardous situation which, if not avoided, could result in death or serious injury. Indicates a potentially hazardous situation which, if not avoided, may result in minor or moderate injury.
Introduction Other documentation HINT: This icon denotes helpful hints and tips. DEFINITION: This icon indicates the definition of a term used in the text. Other documentation Your computer comes with the following documentation: ❖ This electronic user’s guide. ❖ Guides for other programs that may come preinstalled on your computer or that are available for installation on your Recovery Media. ❖ For accessory information, visit Toshiba's Web site at accessories.toshiba.com.
Chapter 1 Getting Started This chapter provides tips for working comfortably, describes how to connect components, and explains what to do the first time you use your notebook computer. Selecting a place to work Your computer is designed to be used in a variety of locations and situations. This section provides guidelines for setting up your computing environment.
Getting Started Selecting a place to work ❖ Equipment that generates a strong electromagnetic field, such as stereo speakers (other than speakers that are connected to the computer) or speakerphones. ❖ Rapid changes in temperature or humidity and sources of temperature change such as air conditioner vents or heaters. ❖ Extreme heat, cold, or humidity. ❖ Liquids and corrosive chemicals.
Getting Started Selecting a place to work 41 Placement of the computer Proper placement of the computer and external devices is important to avoid stress-related injuries. ❖ Place the computer on a flat surface at a comfortable height and distance. You should be able to type without twisting your torso or neck, and look at the screen without slouching. ❖ If you are using an external monitor, the top of the display should be no higher than eye level.
Getting Started Selecting a place to work Whichever type you choose, use the following guidelines to adjust your chair for maximum computing comfort. ❖ Position your chair so that the keyboard is at or slightly below the level of your elbow. You should be able to type comfortably with your shoulders relaxed and your forearms parallel to the floor. If you are using a conventional chair: ❖ Your knees should be slightly higher than your hips.
Getting Started Selecting a place to work 43 Your LCD display has a brightness approaching that of a TV device. We recommend that you adjust the brightness of your LCD to a comfortable level to prevent possible strain on your eyes. Arms and wrists ❖ Avoid bending, arching, or twisting your wrists. Keep them in a relaxed, neutral position while typing. ❖ Exercise your hands, wrists, and arms to improve circulation.
Getting Started Selecting a place to work Other precautions Your notebook computer is designed to provide optimum safety and ease of use, and to withstand the rigors of travel. You should observe certain precautions to further reduce the risk of personal injury or damage to the computer. ❖ Avoid prolonged physical contact with the underside of the computer. If the computer is used for long periods, its case can become very warm.
Getting Started Selecting a place to work 45 Turning off the computer while it is reading from or writing to a disk may damage the disk, the drive, or both. ❖ Keep the computer and disks away from objects that generate strong magnetic fields, such as large stereo speakers. Information on disks is stored magnetically. Placing a magnet too close to a disk can erase important files. ❖ Scan all new files for viruses.
Getting Started Setting up your computer Setting up your computer TECHNICAL NOTE: You must complete all set up steps up to “Setting up your software” before adding external or internal components to your computer. These components include, but are not limited to, a mouse, keyboard, printer, memory, and PC cards. Your computer contains a rechargeable high-capacity battery that needs to be charged before you can use it. To use external power or to charge the battery, you must attach the AC adapter.
Getting Started Setting up your computer NOTE NOTE 47 To register online, your computer must be connected to the Internet via a voice-grade telephone line or a Local-AreaNetwork (LAN). If you chose not to register now, you may register with Toshiba by clicking the Register with Toshiba icon on the desktop. A window displays the message, “Thank you.” 4 Click Finish to continue. Your computer restarts automatically.
Getting Started Connecting to a power source ❖ Connect a mouse (see “Connecting a mouse” on page 68) ❖ Connect a local printer (see “Connecting a printer” on page 69) ❖ Install PC Cards (see “Using PC Cards” on page 148) ❖ Connect an external keyboard (see “Using an external keyboard” on page 68) ❖ Connect another display device (see “Using external display devices” on page 73) ❖ Connect a diskette drive (see “Connecting an optional external diskette drive” on page 72) Connecting to a power
Getting Started Connecting to a power source 49 When you connect the AC adapter to the computer, always follow the steps in the exact order as described in the User's Manual. Connecting the power cable to a live electrical outlet should be the last step otherwise the adapter DC output plug could hold an electrical charge and cause an electrical shock or minor bodily injury when touched. As a general safety precaution, avoid touching any metal parts.
Getting Started Connecting to a power source 2 Plug the AC adapter into the DC-IN. Sample connecting the AC adapter to the computer 3 Connect the power cable to a live electrical outlet. The AC power indicator glows when the computer is connected to an external power source. The battery light: ❖ Glows amber while the battery is being charged. ❖ Glows green when the battery is fully charged. ❖ Is unlit when the computer is not connected to an external power source.
Getting Started Charging the main battery 51 Charging the main battery Before you can use the battery to power the computer, you must charge it. Connect the computer to a live power outlet using the AC adapter and power cable. The AC power light glows green and the battery light glows amber to show that it is charging. Once the computer is connected to a power outlet, you can charge the battery with the computer turned off or on. It takes several hours to charge the battery when the computer is off.
Getting Started Using the computer for the first time Using the computer for the first time The computer is now ready for you to turn it on and begin using it. Opening the display panel 1 Slide the display latch to the right. 2 Lift the display panel. Lift Slide Sample opening the display panel To avoid damaging the display panel, do not force it beyond the point where it moves easily. Never lift or move the computer using the display panel.
Getting Started Using the computer for the first time NOTE 53 Over a period of time, and depending on the usage of the computer, the brightness of the LCD Screen will deteriorate. This is an intrinsic characteristic of LCD technology. Screen will dim when the computer is operated on battery power and you may not be able to increase the brightness of the screen.
Getting Started Using the computer for the first time Sample pressing the power button NOTE When you turn on the computer for the first time, do not turn off the power again until the operating system has loaded completely. The preinstalled operating system loads automatically. The hard disk drive indicator flashes to indicate that the hard disk drive is currently in use. Never turn off the computer while any drive is in use.
Getting Started Using the TouchPad™ 55 The TOSHIBA Console window appears. For more information see “TOSHIBA Console” on page 157. 2 Click Security. 3 Click User password. 4 Follow the on-screen instructions. The password requirement becomes active the next time you turn on your computer. When the feature is active, you must enter the password during the power-on process. After typing your password, press the Enter key. If the password is correct, the power-on process continues.
Getting Started Using the TouchPad™ ❖ To move the cursor to the right side of the page, slide your finger across the TouchPad from left to right. ❖ To move it to the left side, slide your finger from right to left. NOTE Because the TouchPad is much smaller than the display screen, moving your cursor across the screen often means having to move your finger several times across the TouchPad in the preferred direction.
Getting Started Using the TouchPad™ 3 Click the Mouse icon. 4 Click the TouchPAD ON/OFF tab. 57 The TouchPAD ON/OFF tab view window appears. Sample Mouse Properties window 5 Select Disable or Enable, whichever is appropriate. 6 Click Apply. 7 Click OK. The Mouse Properties window closes. 8 Close the Printers and Other Hardware window. 9 Close the Control Panel window. You can also use a hot key (Fn + F9) to disable or enable the TouchPad.
Getting Started Using the TouchPad™ Using TOSHIBA Touch and Launch TOSHIBA Touch and Launch is a program that adds features to the TouchPad. For example, by selecting an icon you can: ❖ Open a document ❖ Launch a program ❖ Show a list of windows and switch the active window ❖ Open Internet Explorer favorites TOSHIBA Touch and Launch is like a miniature Windows® desktop. You can personalize TOSHIBA Touch and Launch to help you work more efficiently.
Getting Started Using the TouchPad™ 59 highlighted in blue and selected, the function corresponding to the selected icon launches and the TOSHIBA Touch and Launch window remains open. To close the TOSHIBA Touch and Launch window, release your finger when the blue circle is not on any icon. Or, highlight the Close icon in the upper right of the TOSHIBA Touch and Launch window.
Getting Started Using the TouchPad™ TOSHIBA Touch and Launch is controlled/adjusted via an icon on the system tray. The icon changes color when the TOSHIBA Touch and Launch is active. Double-click the icon to open the TOSHIBA Touch and Launch Settings window.
Getting Started Using the TouchPad™ 61 In the Corner Assignment section you can change the icons you see at the four corners of the TOSHIBA Touch and Launch window using the drop-down list boxes. The icons are referred to as tables in the TOSHIBA Touch and Launch Settings dialog. The Touch Pad settings button allows you to define how sensitive the TouchPad will be to your finger on the TouchPad before it actives the TOSHIBA Touch and Launch window.
Getting Started Installing additional memory (optional) Installing additional memory (optional) HINT: To purchase additional memory modules, see the accessories information packaged with your system or visit accessories.toshiba.com. Before you install or remove a memory module, turn off the computer using the Start menu. If you install or remove a memory module while the computer is in Stand by or Hibernation mode, data will be lost.
Getting Started Installing additional memory (optional) 63 Do not try to install a memory module under the following conditions. You can damage the computer and the module. 1. The computer is turned on. 2. The computer was shut down using Standby or Hibernation mode. 3. Power to the DVD-ROM or multi-function drive has been turned on. Do not install or remove a memory module while the DVD-ROM or multi-function drive power is on. You need a standard Phillips no.
Getting Started Installing additional memory (optional) Sample using a Phillips-head screwdriver to remove the memory cover 3 Remove the screw that holds the memory cover in place, and remove the memory cover. 4 Remove the new memory module from its antistatic packaging. Static electricity can damage the memory module. Before you handle the module, touch a grounded metal surface to discharge any static electricity you may have built up.
Getting Started Installing additional memory (optional) 65 Sample inserting the memory module Avoid touching the connectors on the memory module or on the computer. Grease or dust on the connectors may cause memory access problems. The clips on either side of the module will click to secure the module. 6 Replace the memory cover and screw. 7 Turn the computer over. 8 Turn on the computer. To verify that the computer correctly recognizes the memory, see “Checking total memory” on page 68.
Getting Started Installing additional memory (optional) Removing a memory module If you use the computer for a long time, the memory module will become hot. If this happens, let the module cool to room temperature before you replace it. Do not try to remove a memory module with the computer turned on. You can damage the computer and the device. Do not remove the memory module while the computer is in Standby mode. The computer could hang up the next time you turn it on and data in memory will be lost.
Getting Started Installing additional memory (optional) 2 67 Pull the clips away from the memory module. The memory module pops partially out of the slot. Sample removing the memory module 3 Carefully remove the module from the slot. Static electricity can damage the memory module. Before you handle the module, touch a grounded metal surface to discharge any static electricity you may have built up.
Getting Started Using an external keyboard Checking total memory When you add or remove memory, you can check that the computer has recognized the change. To do this: 1 Click Start, Control Panel 2 Click Performance and Maintenance. 3 Click System. 4 The General tab view automatically appears and shows the recognized memory.
Getting Started Connecting a printer 69 Connecting a printer You can connect a USB-compatible printer to your computer through the USB ports. You can connect a USB printer after you turn on the computer. Alternatively, you can connect a parallel printer to the computer’s parallel port. Connecting a USB printer To achieve the connection, you need a suitable USB cable, which may come with your printer. Otherwise, you can purchase one from a computer or electronics store.
Getting Started Connecting a printer If your printer has not been detected automatically when connected to the computer, you must install the printer driver for the model of printer that is connected to your computer. You install the printer driver either by following the instructions indicated in your printer guide, or by using the operating system’s Add Printer Wizard. If you plan to set up a printer later, close or cancel the Add Printer Wizard.
Getting Started Connecting a printer The Printers and Faxes window appears. Sample Printers and Faxes window 4 Click Add a printer. The Add Printer Wizard window appears. Sample Add Printer Wizard 5.375 x 8.375 ver 2.
Getting Started Connecting an optional external diskette drive 5 Follow the on-screen instructions. HINT: If you are using more than one printer, make sure the name is descriptive enough to help you tell the difference. Connecting an optional external diskette drive You can attach an optional external USB diskette drive to use diskettes with your computer. This drive: ❖ Holds 3.5-inch high-density (1.44 MB) diskettes for data transfer and storage.
Getting Started Using external display devices 73 Using external display devices Your computer comes with a built-in LCD display, but you can easily attach an external monitor to your computer if you need a larger screen. Once you have connected an external display device, you can choose to use the internal display only, the external device only, or both simultaneously. Connecting an external monitor You must attach the monitor before you turn on the computer.
Getting Started Using external display devices 3 ❖ External device only ❖ Built-in display and TV (or other external video device) simultaneously ❖ TV (or other external video device) only Release the Fn key for the selection to take effect. TECHNICAL NOTE: You can also change these settings using the Display Properties box in the Control Panel.
Getting Started Powering off the computer 75 enabled and the Display area (resolution) set to 640 x 480 or 800 x 600, the image on the internal display panel may appear stretched. NOTE The Windows® XP operating system by default does not display resolutions below 800 x 600. To display the 640 x 480 resolution, you may need to click the Settings tab in the Display Properties window, click Advanced, click the Adapter tab, click List all modes, and select 640 x 480.
Getting Started Caring for your computer ❖ To leave the computer off for a longer period, you can use the Windows® Turn Off command when not connected to a domain server or the Shut down command when connected to a domain server instead. Never turn off the computer while any drive is in use. Doing so may damage the media in use and result in loss of data. For more information, see “Powering down the computer” on page 101.
Getting Started Caring for your computer 77 Moving the computer Before moving your computer, even across the room, make sure all disk activity has ended (the disk activity lights stop glowing) and all external peripheral cables are disconnected. Never pick up the computer by its display panel or by the back (where the ports are located). Although your notebook computer is built to withstand reasonable shock and vibration, transport it in a carrying case for long trips.
Getting Started Caring for your computer 3 Insert the cable’s locking end into the security lock slot, then rotate the key a quarter-turn and remove it. Sample locking the computer The computer is now securely locked to deter computer theft. 5.375 x 8.375 ver 2.
Chapter 2 Learning the Basics This chapter lists some computing tips and provides important information about basic features. Computing tips ❖ Save your work frequently. Your work temporarily stays in the computer’s memory until you save it to the disk. You will lose all unsaved work, if, for example, a system error occurs and you must restart your computer, or your battery runs out of charge while you are working. Your computer can be configured to warn you when the battery is running low.
Learning the Basics Computing tips ❖ Back up your files to storage media on a regular basis. Label the backup copies clearly and store them in a safe place. If your hard disk suddenly fails, you may lose all the data on it unless you have a separate backup copy. ❖ Use Error-Checking and Disk Defragmenter regularly to conserve disk space and help your computer perform at its optimal level. Consult your Windows® XP operating system documentation for more information on these and other utilities.
Learning the Basics Using the keyboard 81 Using the keyboard Sample keyboard Character keys Typing with the character keys is very much like typing on a typewriter, except that: ❖ The spacebar creates a space character instead of just passing over an area of the page. ❖ The lowercase l (el) and the number 1 are not interchangeable. ❖ The uppercase letter O and the number 0 are not interchangeable.
Learning the Basics Using the keyboard Ctrl, Fn, and Alt keys Ctrl Fn Alt . Sample Ctrl, Fn and Alt keys The Ctrl, Fn, and Alt keys do different things depending on the program you are using. For more information, see your program documentation. Function keys The function keys (not to be confused with the Fn key) are the 12 keys at the top of the keyboard. Sample function keys through F12 are called function keys because they run programmed functions when you press them.
Learning the Basics Using the keyboard 83 Overlay keys & ∗ ( ) 7 8 9 0 8 Home 7 U O 4 J P 5 6 K L 1 End ∗ PgUp 9 I 2 - : ; PgDn 3 + > M ? / . 0 Ins Esc F1 F2 F3 1 F4 # @ ! 2 F5 $ 3 F6 % 4 F7 5 F8 F9 W E 6 R 7 T 8 Y A S D F G H X C V B Fn 6 L 2 Ins Ctrl 5 Alt Pause Sys Req Break BkSp { } Home [ ] \ PgUp - " ´ + > ? / .
Learning the Basics Starting a program To use the cursor control overlay when the numeric overlay is on, press and hold down Shift while you use the cursor control keys. To return to the numeric overlay, release Shift. To turn off the numeric keypad overlay, hold down the Fn key and press F11 again. The numeric mode light on the keyboard indicator panel goes out. Using the cursor control overlay To turn on the cursor control overlay, press Fn and F10 simultaneously.
Learning the Basics Starting a program ❖ Use Windows Explorer to locate the program file ❖ Use the Run dialog box 85 Starting a program from the Start menu When you install a program, the operating system usually puts an icon in the All Programs menu. To start a program that has an icon in the All Programs menu, follow these steps, which use the Windows® WordPad program as an example: 1 Click Start, then point to All Programs.
Learning the Basics Starting a program 2 Click Accessories. 3 Click Windows Explorer. 4 Click My Computer to expand the window. 5 In the left part of the window, under the C: icon, doubleclick the folder containing the program, in this case Program Files. Windows® Explorer shows the contents of the Program Files folder on the right side of the window. The left side of the window shows all the folders contained within the Program Files folder. 6 In the left part of the window, click Windows NT.
Learning the Basics Starting a program 87 Sample Run dialog box 2 In the Run dialog box: ❖ If you know the program’s location, type the command line. For a program in the Windows® folder, type just the program name. Otherwise, type the full file path. For example, to access WordPad, type: c:\Program Files\WindowsNT\Accessories\Wordpad, then click OK. ❖ If you do not know the location, click Browse.... In the Browse dialog box, enter the file name (for example, wordpad.
Learning the Basics Saving your work Saving your work Before you turn off the computer, save your work to the hard disk drive. Always save your data even when you are using the Stand by. If your battery fully discharges, your information will be lost. Your computer can be configured to warn you when the battery is running low, see “Power management” on page 117. Saving files 1 On the File menu of your Windows® program, click Save.
Learning the Basics Saving your work 3 89 Type a file name, then click Save. HINT: To make another copy of the file you are currently working with, choose Save As from the File menu and give the new file a different name. The Windows® XP operating system supports file names of up to 255 characters; the names can include spaces. Some applications still require MS-DOS® file names.
Learning the Basics Printing your work To save: ❖ A file you are updating, open the program’s File menu and click Save. ❖ A new file, choose Save As from the File menu, type a name for the file, and click OK. HINT: To make another copy of the file you are currently working with, choose Save As from the File menu and give the new file a different name. Printing your work Verify that the Windows® XP operating system is set up for your printer as described in “Setting up a printer” on page 69.
Learning the Basics Backing up your files 91 Backing up your files Backing up your files means copying individual files to media, such as a CD. Or copying entire sections of your hard disk to another device such as a tape drive or to your network partition. To back up to a CD, optional diskette drive, or other media: 1 Insert the media into the appropriate drive. 2 Click Start, then click My Computer. 3 Double-click the drive that contains the file you want to copy.
Learning the Basics Using the DVD-ROM or multi-function drive TECHNICAL NOTE: When restoring files, the backup program prompts you if you try to overwrite a file that already exists on the hard disk. Make sure the backup version is the one you want before overwriting the existing file. Using the DVD-ROM or multi-function drive Optical storage has become the preferred medium for software, music, and video.
Learning the Basics Using the DVD-ROM or multi-function drive 93 DVD-ROM or multi-function drive components Your DVD-ROM or multi-function drive may look like this: Eject button Manual eject hole Sample DVD-ROM or multi-function drive Never press the eject button or turn off the computer while the drive-in-use indicator light is glowing. Doing so could damage the disc or the drive. The eject button requires power to operate. The manual eject button does not require power.
Learning the Basics Using the DVD-ROM or multi-function drive The previous track button returns to the preceding track on the disc. The next track button skips to the following track on the disc. The play/pause button starts playing the disc or makes it pause if currently playing. The stop/eject button stops a disc that is currently playing. Do not install or remove a memory module while the DVDROM or multi-function drive power is on. Inserting a disc Before playing an audio CD, turn the volume down.
Learning the Basics Using the DVD-ROM or multi-function drive 3 95 Hold the disc by its edges and check that it is clean and free of dust. Handle discs carefully. Avoid touching the surface of the disc. Grasp it by its center hole and edge. If you handle the disc incorrectly, you could lose data. 4 Carefully place the disc in the empty tray with its label facing up. Sample inserting a disc Be careful not to touch the drive’s lens (located underneath the drive’s spindle) or the area around it.
Learning the Basics Using the DVD-ROM or multi-function drive Spindle Correct position Disc Incorrect position Incorrect position Sample positioning the disc on the spindle Make sure the disc is properly positioned on the spindle. If you position the disc incorrectly, it can jam the disc tray. 6 Close the disc tray by pressing gently on the center of the tray until it clicks indicating that it is locked. Playing an audio CD Insert an audio CD and close the disc tray.
Learning the Basics Using the DVD-ROM or multi-function drive Sample Audio CD window The Windows Media® Player window appears. 5.375 x 8.375 ver 2.
Learning the Basics Using the DVD-ROM or multi-function drive Rewind Play Fast forward Stop Volume control Previous track Next track Mute Sample Windows Media® Player window The Windows Media® Player control panel works much like an ordinary compact disc player: ❖ To play the CD or to pause, click the Play/Pause button on the CD Player control panel. ❖ To stop the CD, click the Stop button.
Learning the Basics Using the DVD-ROM or multi-function drive 1 Open the Start menu and select My Computer. 2 Click the DVD-ROM/multi-function drive icon. 99 The disk drive will run the CD. If your disk does not run using this method, try using an application that is associated with the media on the disk. For example, if it is a music CD, open Windows® Media Player and point it to play the CD. For other types of media, use the associated software to open the files on the disk.
Learning the Basics Using the DVD-ROM or multi-function drive Removing a disc with the computer on Never press the eject button or turn off the computer while the drive-in-use light is glowing. Doing so could damage the disk or the drive. 1 Locate and press the eject button. The disc tray partially opens. 2 Grasp the sides of the disc tray and pull it fully open. 3 Remove the disc from the disc tray and place it in its protective cover.
Learning the Basics Powering down the computer 101 Caring for CD and DVD discs ❖ Store your discs in their original containers to protect them from scratches and keep them clean. ❖ Never bend a disc or place heavy objects on top of it. ❖ Hold a disc by its outside edge. Fingerprints on the surface of a compact disc can prevent the drive from reading the data properly. ❖ Avoid exposing discs to direct sunlight or extreme heat or cold.
Learning the Basics Powering down the computer Each option has its advantages. TECHNICAL NOTES: Before using any of these options to power down your computer, save your files and make sure the disk activity lights are off. If you change your mind and decide to continue working after all, wait a few seconds before turning the computer on again. Turn Off or Shut down command The Turn Off or Shut down commands power off the computer. The Windows® XP Home operating system uses the Turn Off command.
Learning the Basics Powering down the computer 103 Restart command Restart is the same as Turn Off or Shut down but automatically powers up the computer. Use it when you need to reload the operating system, for example to activate changes to system settings. Hibernation command The Hibernation command shuts the computer down completely, but it first saves the current state of the computer to the hard disk.
Learning the Basics Powering down the computer Standby command Standby puts the computer into a power-saving mode. Standby holds the current state of the computer in memory so that, when you restart the computer, you can continue working from where you left off. Factors when choosing Standby: ❖ While in Standby mode, the computer uses some battery power. The battery will eventually discharge in Standby mode.
Learning the Basics Using Turn Off or Shut down 105 Using Turn Off or Shut down If you are using the Windows® XP Home operating system, or are using the Windows® XP Professional operating system and are not a member of a domain, power off the computer as follows: 1 Click Start, Turn off computer. The Turn off computer window appears. Sample Turn off computer window 2 Click Turn Off. The computer turns itself off.
Learning the Basics Using Turn Off or Shut down Sample Shut down computer window 2 Select Shut down from the drop-down list. 3 Click OK. The computer turns itself off. NOTE Holding the Shift key while the Turn Off computer Windows® dialog box is open, changes the Standby button to hibernate. For more information about setting up hibernation “Hibernation command” on page 103 and “Using Hibernation” on page 108.
Learning the Basics Using Turn Off or Shut down 107 Sample TOSHIBA Power Saver Properties window 4 Select Shut down for the options you want. ❖ When I press the power button Set this option to Shut down to have the computer shut down when you press the power button. ❖ When I close the lid Set this option to Shut down to have the computer shut down when you close the display panel. 5 Click Apply. 6 Click OK.
Learning the Basics Using Hibernation Starting again after Turn Off or Shut down To start the computer up again, press and release the power button. The on/off light turns on. Using Hibernation When Hibernation is enabled, you can put the computer into Hibernation in more than one way. Enabling the Hibernation command Hibernation enabled is a default setting. If it should become disabled, you can enable it by right-clicking the Power Saver icon in the system tray.
Learning the Basics Using Hibernation 109 Sample Turn off computer window with shift key held down to show Hibernate option 2 Hold down the Shift key and click Hibernate (“Hibernate” only appears when the Shift key is pressed). The computer saves the state of the system, including all open programs and files, to the hard disk. Then the computer turns itself off.
Learning the Basics Using Hibernation The computer saves the state of the system, including all open programs and files, to the hard disk. Then the computer turns itself off. Going into Hibernation mode more quickly You can also put the computer into Hibernation mode in the following ways: ❖ By pressing the hotkey combination Fn + F4. See “Hibernation mode” on page 201.
Learning the Basics Using Hibernation 111 Sample TOSHIBA Power Saver Properties window 4 Select Hibernation for the options you want. ❖ When I press the power button Set this option to Hibernate so that the computer will go into Hibernation mode when you press the power button. ❖ When I close the lid Set this option to Hibernate so that the computer will go into Hibernation mode when you close the display panel. 5 Click Apply. 6 Click OK.
Learning the Basics Using Standby Starting again from Hibernation mode To start the computer from Hibernation mode, press and release the power button. The computer returns to the screen you were using. If you put the computer in Hibernation mode by closing the display panel, you can start it again by opening the display panel. NOTE If your computer is running on batteries, you cannot start it again by opening the display panel. To turn the system back on, press the power button.
Learning the Basics Using Standby 113 mode. The on/off light ( ) blinks amber indicating the machine is in Standby mode. If you are using the Windows® XP Professional operating system and are a member of a domain, power off the computer using the Standby command as follows: 1 Click Start, then Shut down. The Shut Down window appears. Sample Stand by window 2 Select Stand by from the drop-down list of options. 3 Click OK.
Learning the Basics Using Standby See “Standby mode” on page 200. ❖ By pressing the power button ❖ By closing the display panel To put the computer into Standby mode when you press the power button or close the display panel, you must preset the mode: 1 Open the Start menu, click Control Panel then Performance and Maintenance. 2 Click the Toshiba Power Saver icon. 3 Click the Setup Action tab. The TOSHIBA Power Saver Properties window appears.
Learning the Basics Toshiba’s online resources 115 Set this option to Standby to put the computer into Standby mode when you close the display panel. 5 Click Apply. 6 Click OK. NOTE For more information about the Power Saver utility, see “Power Management” on page 159. Starting again from Standby To start the computer from Standby mode, press the power button. The computer returns to the screen you were using.
Chapter 3 Mobile Computing This chapter covers all aspects of using your computer while traveling. Toshiba’s energy-saver design Your computer enters a low-power standby mode when it is not being used, thereby conserving energy and saving money in the process. It has a number of other features that enhance its energy efficiency. Many of these energy-saving features have been set by Toshiba.
Mobile Computing Running the computer on battery power 117 Battery Notice Battery life may vary depending on applications, power management settings. and features utilized. Recharge time varies depending on usage. The battery does not charge while the computer is using all of its power to run applications and devices. After a period of time, the battery will lose its ability to perform at maximum capacity and will need to be replaced. This is normal for all batteries.
Mobile Computing Charging the batteries Changes to these settings may result in system performance or stability issues. Users who are not completely familiar with the power management component of the system should use the preset configuration. For assistance with setup changes, contact the Toshiba Global Support Centre.
Mobile Computing Charging the batteries 119 Never leave batteries in the battery charger for more than a week at a time. Doing so may reduce the potential charge of the battery. Use only battery chargers designed to work with your notebook computer. You can order a Toshiba battery charger from Toshiba’s Web site at accessories.toshiba.com. Charging the main battery To charge the battery, plug the computer into a live wall outlet. It takes several hours to charge the battery with the computer off.
Mobile Computing Charging the batteries Leave the power connected, and the battery should begin charging after a few minutes. HINT: Once the battery is fully charged, we recommend that you operate your computer on battery power until the battery discharges completely. Doing this extends battery life and helps ensure accurate monitoring of battery capacity. For more information, see “Maximizing battery life” on page 129.
Mobile Computing Monitoring battery power NOTE 121 It is seldom necessary to charge the RTC battery because it charges while the computer is on. If the RTC battery is low, the real-time clock and calendar may display the incorrect time and date or stop working. When Hibernation mode is enabled and the RTC battery is completely discharged, a warning prompts you to reset the real-time clock.
Mobile Computing Monitoring battery power 1 Open the Start menu, click Control Panel then Performance and Maintenance. 2 Click the Toshiba Power Saver icon. The Toshiba Power Saver Properties window appears. Sample Toshiba Power Saver Properties window The remaining battery charge is indicated on the top left side of the dialog box. With repeated discharges and recharges, the battery’s capacity will gradually decrease.
Mobile Computing Monitoring battery power 123 The Windows® operating system has additional power management options that can be accessed through an icon in the Control Panel. For more information, see “Power Management” on page 159. Conserving battery power How long a fully charged battery pack lasts when you are using the computer depends on a number of factors, such as: ❖ How the computer is configured.
Mobile Computing Monitoring battery power What to do when the battery runs low When the battery runs low you can: ❖ Plug the computer into an external power source and recharge the battery. ❖ Put the computer in Hibernate mode and replace the battery with a charged spare. ❖ Save your work and turn off the computer. If you do not manage to do any of these things before the battery completely runs out of power, the computer automatically enters Hibernate mode and turns itself off.
Mobile Computing Changing the main battery 125 Changing the main battery When your battery power is running low, you have two options—connect the computer to an AC power source or install a charged battery. When handling a battery, be careful not to drop it or shortcircuit its terminals. Also, do not drop, hit or otherwise impact the battery. Do not scratch or break the casing and do not twist or bend the battery pack. Do not remove the battery pack while the computer is in Standby mode.
5 Mobile Computing Changing the main battery If the battery lock latches are in the locked position (toward the left of the computer), slide them towards the right of the computer. Sample releasing the battery lock 6 Slide the battery release latch to release the battery. Sample releasing the battery 5.375 x 8.375 ver 2.
Mobile Computing Changing the main battery 7 127 While still holding the release latch in the open position, lift the battery pack out of the computer. Sample removing the battery If the battery is leaking or its case is cracked, put on protective gloves to handle it, and discard it immediately following the advice in “Disposing of used batteries safely” on page 130.
Mobile Computing Taking care of your battery Taking care of your battery The following sections offer tips on how to take care of your battery and prolong its life. Safety precautions ❖ If the battery pack produces an odor, overheats or changes color or shape while it is being used or charged, turn off the computer’s power immediately and disconnect the power cord from the power socket. Carefully remove the battery pack from the computer. ❖ Do not try to disassemble a battery pack.
Mobile Computing Taking care of your battery ❖ 129 Do not expose the battery pack to fire. The battery pack could explode. Maximizing battery life To maximize the life of your battery pack: ❖ At least once a month, disconnect the computer from a power source and operate it on battery power until the battery pack fully discharges. Before doing so, follow the steps below: 1 Turn off the computer’s power. 2 Disconnect the AC adapter and turn on the computer’s power. If it does not turn on, go to step 4.
Mobile Computing Disposing of used batteries safely ❖ If you are not going to use the computer for more than eight hours, disconnect the AC adapter. ❖ Store spare battery packs in a cool dry place out of direct sunlight. Disposing of used batteries safely The life of a battery pack should last for years. When the battery pack needs replacing, the main battery light flashes amber shortly after you have fully recharged the battery. You must discard a battery if it becomes damaged.
Mobile Computing Traveling tips 131 Traveling tips The environmental precautions listed in “Selecting a place to work” on page 39, also apply while traveling. ❖ Never leave your computer on a sunny ledge or in a place where it could get wet or covered in dust. ❖ Always travel with the computer in a carrying case. Toshiba offers a choice of carrying cases for the computer. They all provide plenty of extra space for manuals, power cables, and compact discs.
Chapter 4 Exploring Your Options In this chapter, you will explore some of the special features of your Satellite® Series notebook computer. Exploring the desktop The desktop is the launching pad for everything you can do in the Windows® XP Home or XP Professional operating system. You use its features to start programs, find documents, set up system components, and perform most other computing tasks.
Exploring Your Options Exploring the desktop 133 Finding your way around the desktop Your computer’s desktop includes several standard features: icons, Start button, taskbar, system tray, and background pattern. Icons Taskbar Start button System tray ® Sample Windows XP operating system desktop Icons An icon represents a folder, file, or program that can be quickly activated by double-clicking the icon.
Exploring Your Options Exploring the desktop Recycle Bin — Holds files you have deleted. You may be able to retrieve these files until you empty the Recycle Bin. TECHNICAL NOTE: If you delete a file from a diskette, it does not go into the Recycle Bin. For more information on the Recycle Bin, see Windows online Help. Internet Explorer — The Microsoft® browser that provides access to the Internet. NOTE If you place the cursor over an icon, a popup description of the file contents appears.
Exploring Your Options Exploring the desktop 135 Taskbar Each time you open a program, a button associated with that program appears on the taskbar. With some programs, a button appears on the taskbar for each document or window you open. You can use these buttons to quickly switch between the programs or windows. To make a program or window the currently active one, click the associated taskbar button.
Exploring Your Options Setting up for communications Setting up for communications Your computer comes with a built-in modem that can be connected to a standard voice-grade telephone line. The modem allows you to: ❖ Access the Internet. ❖ Communicate with your office’s local area network (LAN), or a larger corporate wide area network (WAN). For specific information about connecting to a LAN or WAN, consult your network administrator. ❖ Send a fax directly from your computer.
Exploring Your Options Setting up for communications 137 The following procedure is intended to support you if you need to either upgrade your modem or reset the port to the default settings. If you are having trouble connecting through the modem, you may need to determine the current COM port name and possibly change it. To find out which port your modem is connected to: 1 Open the Start menu, and click Control Panel. 2 Click Printers and Other Hardware. 3 Click Phone and Modem Options.
Exploring Your Options Setting up for communications Connecting the modem to a telephone line Before you can communicate using the modem, you need to connect it to a telephone line. Your computer’s built-in modem port provides an RJ-11 jack, allowing you to connect the modem to a standard voice-grade telephone line. 1 Plug one end of a telephone cable (purchased separately) into the modem port on the back of the computer. 2 Connect the other end to an RJ-11 wall jack.
Exploring Your Options Setting up for communications 139 Setting up the connection To set up an office connection, consult your network administrator for network settings and additional considerations. To use a dial-up connection, have your network administrator configure your computer for the network and supply you with the telephone number for the dial-up connection. To set up the network connection, use the Dial-Up Networking Wizard: 1 Click Start and point to All Programs.
Exploring Your Options An overview of using the Internet To use your wireless communication, flip the wireless antenna on/off switch to the On position. Using the Wi-Fi® Wireless LAN Mini PCI module Your computer may have an integrated Wi-Fi Wireless LAN Mini PCI module. It is recommended that you do not remove the module from your computer. For assistance, contact a Toshiba Wireless Authorized Service Partner. For systems equipped with Wi-Fi, flip the wireless on/off switch to the On position.
Exploring Your Options An overview of using the Internet 141 The World Wide Web The World Wide Web (or “Web”) is a subset of the Internet— a collection of interlinked documents (located on computers connected to the Internet) that work together using a specific Internet protocol called Hypertext Transfer Protocol (HTTP). The World Wide Web offers information as text, images, audio, or video to be referenced from anywhere in the world.
Exploring Your Options An overview of using the Internet Once you have established an ISP account, you can connect to the Internet. 1 Connect your computer’s modem to a telephone line. For more information on connecting a modem, see “Connecting the modem to a telephone line” on page 138. 2 Start your Web browser. Have your modem dial the ISP’s telephone number, and establish a connection with the ISP’s computer.
Exploring Your Options An overview of using the Internet 143 Internet features The Internet offers many types of communication tools to help you perform many tasks. ❖ Internet email To send and receive your own email, you need a mailbox on the Web or an email address. If you have an account with an ISP, you can probably set up an email address at the same time you sign up for the service.
Exploring Your Options Exploring video features Exploring video features Your computer’s video features enable you to view Windows® presentations or DVD movies on the computer screen (display panel or external monitor). For information on connecting an external monitor, see “Using external display devices” on page 73. Changing the display properties setting 1 Right-click anywhere on your desktop and select Properties. The Display Properties dialog box appears.
Exploring Your Options Exploring audio features 145 4 The Monitor Settings window appears and asks if you want to keep the settings. 5 Click Yes. 6 To change the settings back, repeat steps 2 through 5. Playing DVDs Your computer must be on for you to use the DVD-ROM or multi-function drive. 1 Open the DVD-ROM or multi-function drive tray. 2 Place the DVD in the DVD-ROM or multi-function drive.
Exploring Your Options Exploring audio features Recording sounds You can make audio recordings and save them as .wav files by connecting an external microphone or other sound source to the microphone jack and using the Sound Recorder feature in the operating system. DEFINITION: A .wav (pronounced “wave”) file is a format for storing sound in files. TECHNICAL NOTE: If you record MP3 files, you will only be able to play them on a device capable of playing MP3 files.
Exploring Your Options Exploring audio features 3 NOTE 147 Click the Record button and speak normally into the microphone. You can only record 60 seconds at a time. 4 When you have finished recording, click the Stop button. 5 To hear what you just recorded, click the Play button. 6 To save the file, select Save from the File menu. Adjusting recording settings The better the quality of the recording, the more disk space the sound file requires. Experiment to find a balance that fits your needs.
Exploring Your Options Using PC Cards TECHNICAL NOTE: Use amplified speakers that require an external power source. Other types of speakers will be inadequate to produce sound from the computer. To play back sound files through external speakers or headphones: 1 Locate the headphone jack. 2 Using any necessary adapters, plug the cable from the headphones or external speakers into the headphone jack. The headphone jack requires a 16-ohm stereo mini-jack.
Exploring Your Options Using PC Cards 149 To insert a PC Card: 1 Turn off the computer. You may also hot swap a PC Card (see “Hot swapping” on page 150). 2 Align the card connectors with the PC Card slot and carefully slide the card into the slot until it locks into place. Sample inserting a PC Card To avoid damaging the PC Card or the computer, do not force the card into the PC Card slot. Removing PC Cards 1 Stop the PC Card by clicking the Safely Remove Hardware icon on the system tray.
Exploring Your Options Using PC Cards Sample removing a PC Card 3 Remove the PC Card and store it properly. Hot swapping One of the great things about PC Cards is that you can replace one PC Card with another while the computer is on. This is called “hot swapping.” Hot swapping precautions Although you can insert a PC Card at any time, to avoid data loss never remove a card while it is in use. For example: ❖ Never remove a hard disk card while the system is accessing it.
Chapter 5 Toshiba Utilities Your computer includes several utilities designed to help you to configure your system to best meet your individual needs. Together, these allow you to ascertain certain system details, set additional options, or change default options. These utilities are described in this chapter: ❖ TOSHIBA Accessibility ❖ Fn-esse ❖ Hotkey utility ❖ TOSHIBA Console ❖ TOSHIBA Zooming Utility ❖ Application Launch Button 151 5.375 x 8.375 ver 2.
Toshiba Utilities TOSHIBA Accessibility TOSHIBA Accessibility The TOSHIBA Accessibility utility allows you to use the Fn key to create a hot key combination with one of the function keys without pressing the two keys simultaneously as is usually required. Using Accessibility enables you to make the Fn key a sticky key, meaning you can press it once, release it and then press a function key to activate the hot key function. To open Accessibility: 1 Click Start, then click All Programs.
Toshiba Utilities Fn-esse 153 Fn-esse The operating system shortcuts and Toshiba’s Fn-esse program provide quick ways to open programs, documents, and folders from within any program without using the Start menu. This section describes how to use the Fn-esse program to quickly access your programs and files.
Toshiba Utilities Fn-esse The keys are color-coded as follows: ❖ Available keys are white. ❖ Assigned keys and keys associated with a popup list are shown on the Fn-esse keyboard in the selected color. ❖ Unavailable keys are dark gray. Assigning a key to a program or document There are two ways to assign a key to open a program or document: ❖ Drag-and-drop ❖ Use the keyboard The method most often used is drag-and-drop.
Toshiba Utilities Fn-esse 155 The program or document is now associated with the key you just selected. To open the program or document, press Fn plus the appropriate key. Using the keyboard To assign a key to open a program or document: 1 Start Fn-esse. 2 Using the keyboard, press and hold the Fn key, then press the desired assignment key. The Assignment Type window appears. HINT: If you are making a direct key assignment, complete step 3. If you are making a popup assignment, complete step 4.
Toshiba Utilities Fn-esse ❖ To create a popup list with items from various folders, or to pick only a few items from a folder, create a new folder containing only the desired programs and documents. If you are unsure how to do this, refer to your operating system documentation. ❖ Click OK to associate the folder with the key you just selected. ❖ To open a popup list showing the items in that folder, press Fn plus the appropriate key.
Toshiba Utilities Hotkey utility 157 Hotkey utility The hotkey utility allows you to receive a confirmation message when you use the hot key combination for Standby [Fn + F3] and Hibernation [Fn + F4]. To activate the utility: Click Start, All Programs, Toshiba, Utilities, Hotkey utility. The Toshiba Hotkey utility window appears. Sample Toshiba Hotkey utility window 4 Put a check mark next to the desired option. 5 Click OK.
❖ Toshiba Utilities TOSHIBA Console Use the Start menu. If you use the Start menu, do the following: 1 Click Start, then click All Programs. 2 Point to TOSHIBA, then Utilities, then click the resulting Console selection. The TOSHIBA Console window appears. Sample TOSHIBA Console window The TOSHIBA Console offers the following features: ❖ Customize Your Computer ❖ Security 5.375 x 8.375 ver 2.
Toshiba Utilities TOSHIBA Console 159 Customize Your Computer The features available in this category are: ❖ Power Management (See “Power Management” on page 159.) ❖ Mouse (properties) ❖ Hotkey assignment (See “Fn-esse” on page 153.) ❖ Toshiba Hardware (See “Toshiba Hardware Setup” on page 161.) ❖ ConfigFree (See “Using ConfigFree™ with your Toshiba Computer” on page 205.
Toshiba Utilities TOSHIBA Console Sample TOSHIBA Power Saver Properties window The TOSHIBA Power Saver Properties window shows the power profiles, which are optimized for several different working environments. You can either use one of the preset modes or create and use your own customized profile. The preset profiles cannot be deleted. By changing the options that appear in the TOSHIBA Power Saver Properties window and clicking OK, you can reconfigure that function.
Toshiba Utilities TOSHIBA Console ❖ DVD Playback ❖ Presentation ❖ Long Life 161 Although you can change the properties for any of these profiles, this is not recommended. If you need a customized profile, create a new profile with the properties you require. The DVD Playback profile applies only when a DVD program is playing. Quickly creating a new power mode 1 Highlight one of the preset profiles. 2 Click Copy.
Toshiba Utilities TOSHIBA Console Sample TOSHIBA HWSetup window The TOSHIBA HWSetup window appears with tabs for the following: ❖ Boot Priority — Allows you to change the sequence in which your computer searches the drives for the operating system. You can also manually choose the Boot Priority by pressing the power button, then quickly pressing the F12 key, or the right or left arrow keys. Select the boot device by pressing the right or left arrow keys or the F12 key. Then press the Enter key.
Toshiba Utilities TOSHIBA Zooming Utility 163 ❖ Keyboard — Allows you to enable or disable the “wakeup on keyboard” feature. The feature allows you to “wake” the machine from Standby by pressing a key. ❖ USB — Allows you to enable or disable USB Legacy Emulation. ❖ LAN — Lets you enable or disable LAN features. ❖ General — Shows the BIOS version, and allows you to set BIOS defaults. ❖ Password — Allows you to set or reset a user password for the power-on process and for instant security.
Toshiba Utilities Application Launch Button Sample TOSHIBA Zooming Utility Properties screen To zoom in, hold down the Fn key and press 2; to zoom out, hold down the Fn key and press 1. Application Launch Button The Application Launch Button (located to the right of the power button) allows you to quickly launch applications. Initially, the button is assigned to launch Internet Explorer.
Chapter 6 If Something Goes Wrong Some problems you may encounter when using your notebook computer are relatively easy to identify and solve. Others may require help from your dealer or the manufacturer of a software program. This chapter aims to help you solve many problems by yourself. It covers the problems you are most likely to encounter. If all else fails, contact Toshiba. You will find information on Toshiba’s support services at the end of this chapter.
If Something Goes Wrong Problems that are easy to fix To close a program that has stopped responding: 1 Press Ctrl, Alt, and Del simultaneously (once). The Windows Task Manager window appears. 2 Click the Applications tab. If a program has stopped responding, the words “not responding” appear beside its name in the list. 3 Select the program you want to close, then click End Task. Closing the failed program should allow you to continue working. If it does not, continue with step 4.
If Something Goes Wrong Problems when you turn on the computer 167 5 Press Enter to add a paragraph break and type some notes describing what you were doing when you received the message. 6 Save the file and refer to it when you contact the software manufacturer. Problems when you turn on the computer These problems may occur when you turn on the power. The computer will not start. Make sure you attached the AC adapter and power cable properly or installed a charged battery.
If Something Goes Wrong The Windows® operating system is not working diskette drive, press the left or right arrow key and choose your boot-up device. HINT: Press F12 as you power on the computer to access the boot priority menu. The computer displays the WARNING RESUME FAILURE message. The computer was placed in Standby mode and the battery has discharged. Data stored in the computer’s memory has been lost. To recharge the RTC battery, connect the computer and leave it powered on for 24 hours.
If Something Goes Wrong The Windows operating system is not working ® 169 ❖ The operating system responds differently from the normal routine. ❖ The screen does not look right. Unless a hardware device has failed, problems usually occur when you change the system in some way such as installing a new program or adding a device. If you experience any of these problems, use the options in the Startup menu to fix the problem.
If Something Goes Wrong The Windows® operating system is not working ❖ Reboot ❖ Return to OS Choices Menu See your Windows® documentation for further explanation. TECHNICAL NOTE: If your computer is connected to a network, the Startup menu may display different versions of Safe mode. Internet problems My Internet connection is very slow. Many factors contribute to the speed with which you can surf the Internet.
If Something Goes Wrong Resolving a hardware conflict 171 To access Windows® XP Help and Support: 1 Click Start, then click Help and Support. The Help and Support Center window appears. 2 Then do one or both of the following: ❖ In the search field, type in the topic of the problem with which you need help and follow the on-screen instructions. ❖ Click a problem you would like help with from the listings and follow the on-screen instructions.
If Something Goes Wrong Resolving a hardware conflict The recommended procedure for getting multiple devices to work together is to add and set up one device at a time. After you add each device, test it to make sure it and all previously connected devices work. The device most recently connected to the system is the one most likely to be causing a hardware conflict. Resolving hardware conflicts on your own Computer components need resources to accomplish a task.
If Something Goes Wrong Resolving a hardware conflict 173 Plug and Play With Plug and Play and the Windows® XP operating system, avoiding hardware conflicts is easy. Plug and Play is a computer standard that helps the system BIOS (basic input/ output system) and the operating system to automatically assign resources to Plug and Play-compliant devices. In theory, if every device connected to the computer is Plug and Play-compliant, no two devices will compete for the same system resources.
If Something Goes Wrong Resolving a hardware conflict Fixing a problem with Device Manager Device Manager provides a way to check and change the configuration of a device. Changing the default settings using Device Manager can cause other conflicts that make one or more devices unusable. Device Manager is a configuration tool for advanced users who understand configuration parameters and the ramifications of changing them.
If Something Goes Wrong Resolving a hardware conflict 175 To check a device’s properties: 1 Click Start, Control Panel, Performance and Maintenance, Administrative Tools. 2 Double-click the Computer Management icon. 3 In the left pane, click Device Manager. 4 To view the device(s) installed, double-click the device type. 5 To view the properties, double-click the device. The operating system displays the Device Properties window, which provides an array of tabs.
If Something Goes Wrong Resolving a hardware conflict Memory module problems Static electricity can damage the memory module. Before you handle the module, touch a grounded metal surface to discharge any static electricity you may have built up. To avoid damaging the memory module, be careful not to touch its gold connector bar (on the side you insert into the computer). An incorrectly connected or faulty memory module may cause errors that seem to be device-related.
If Something Goes Wrong Resolving a hardware conflict 177 Power and the batteries Your computer receives its power through the AC adapter and power cable or from the system batteries (main battery and real-time clock (RTC) battery). Power problems are interrelated. For example, a faulty AC adapter or power cable will neither power the computer nor recharge the batteries.
If Something Goes Wrong Resolving a hardware conflict If the battery light does not glow after 20 minutes, the battery may have reached the end of its useful life. Try replacing it. The battery appears not to power the computer for as long as it usually does. If you frequently recharge a partially charged battery, it may not charge fully. Let the battery discharge completely, then try charging it again. Check the power options using the Power Management utility.
If Something Goes Wrong Resolving a hardware conflict 179 You have connected an external keyboard and the operating system displays one or more keyboard error messages. If you have a second keyboard, try it. If it works, the first keyboard may be defective or incompatible with your computer. Display problems Here are some typical display problems and their solutions: The display is blank. Display Auto Off may have gone into effect. Press any key to activate the screen.
If Something Goes Wrong Resolving a hardware conflict If you are using an external monitor: ❖ Check that the monitor is turned on. ❖ Check that the monitor’s power cable is firmly plugged into a working power outlet. ❖ Check that the cable connecting the external monitor to the computer is firmly attached. ❖ Try adjusting the contrast and brightness controls on the external monitor. ❖ Make sure the display choice is not set for the built-in screen only. The screen does not look right.
If Something Goes Wrong Resolving a hardware conflict 181 To change the display properties: 1 Point at the desktop and click with the secondary button. The Display Properties window appears. 2 Click Properties, then click the Settings tab. 3 Adjust the screen resolution and/or color quality. 4 Click OK. The display mode is set to Simultaneous and the external display device does not work. Make sure the external monitor is capable of displaying at resolutions of 800 x 600 or higher.
If Something Goes Wrong Resolving a hardware conflict Disk drive problems Problems with the hard disk or with a diskette drive usually show up as an inability to access the disk or as sector errors. Sometimes a disk problem may cause one or more files to appear to have garbage in them. Typical disk problems are: You are having trouble accessing a disk, or one or more files appear to be missing. Make sure you are identifying the drive by its correct name (A: or C:).
If Something Goes Wrong Resolving a hardware conflict 183 Your hard disk seems very slow. If you have been using your computer for some time, your files may have become fragmented. Run Disk Defragmenter. To do this, click Start, then click All Programs, point to Accessories and System Tools, and click Disk Defragmenter. Your data files are damaged or corrupted. Refer to your software documentation for file recovery procedures. Many software packages automatically create backup files.
If Something Goes Wrong Resolving a hardware conflict The drive cannot read a diskette. Try another diskette. If you can access the second diskette, the first diskette (not the drive) is probably causing the problem. Run Error-checking on the faulty diskette (for instructions, see “Disk drive problems” on page 182). DVD-ROM or multi-function drive problems You cannot access a disc in the drive. Make sure the drive tray has closed properly. Press gently until it clicks into place.
If Something Goes Wrong Resolving a hardware conflict 185 Some discs run correctly, but others do not. If the problem is with an application CD-ROM, refer to the software’s documentation and check that the hardware configuration meets the program’s needs. The color of the materials used to make the disc can affect its reliability. Silver-colored CD-ROMs are the most reliable, followed by gold-colored CD-ROM. Green-colored CDROMs are the least reliable.
If Something Goes Wrong Resolving a hardware conflict Sample Secondary IDE Channel Properties window 7 Click the Advanced Settings tab. 8 Look at Device 0. The current transfer mode should be Ultra DMA Mode 2. If it is not, select Ultra DMA Mode 2 from the pull-down menu and click OK. Sound system problems You do not hear any sound from the computer. Adjust the volume control. If you are using external headphones or speakers, check that they are securely connected to your computer.
If Something Goes Wrong Resolving a hardware conflict 187 in the Mixer Utility (default Enabled), may cause feedback. Revert to the default settings. PC Card problems PC Cards (PCMCIA-compatible) include many types of devices, such as a removable hard disk, additional memory, or a pager. Most PC Card problems occur during installation and setup of new cards. If you’re having trouble getting one or more of these devices to work together, several sections in this chapter may apply.
If Something Goes Wrong Resolving a hardware conflict PC Card checklist ❖ Make sure the card is inserted properly into the slot. See “Using PC Cards” on page 148 for how to insert PC Cards. ❖ Make sure all cables are securely connected. ❖ Occasionally a defective PC Card slips through quality control. If another PCMCIA-equipped computer is available, try the card in that machine. If the card malfunctions again, it may be defective.
If Something Goes Wrong Resolving a hardware conflict 189 The computer stops working (hangs) when you insert a PC Card. Remove the PC Card. If removing the PC Card does not resolve the problem, try restarting the computer. If the computer still does not work, contact the PC Card’s manufacturer. Hot swapping (removing one PC Card and inserting another without turning the computer off) fails. Follow this procedure before you remove a PC Card: 1 Click the Safely Remove Hardware icon on the System tray.
If Something Goes Wrong Resolving a hardware conflict Printer problems This section lists some of the most common printer problems: The printer will not print. Check that the printer is connected to a working power outlet, turned on and ready (on line). Check that the printer has plenty of paper. Some printers will not start printing when there are just two or three sheets of paper left in the tray. Make sure the printer cable is firmly attached to the computer and the printer.
If Something Goes Wrong Resolving a hardware conflict 191 Modem problems This section lists common modem problems: The modem will not receive or transmit properly. Make sure the cable from the modem to the telephone line is firmly connected to the computer’s modem port and the telephone line jack. Check the port settings to make sure the hardware and software are referring to the same COM port. See “Determining the COM port” on page 136.
If Something Goes Wrong Develop good computing habits Develop good computing habits Make sure you are prepared. Save your work frequently. You can never predict when your computer will lock, forcing you to close a program and lose unsaved changes. Many software programs build in an automatic backup, but you should not rely solely on this feature. Save your work! See “Computing tips” on page 79 for instructions. On a regular basis, back up the information stored on your hard disk.
If Something Goes Wrong If you need further assistance 193 Your local computer store or book store sells a variety of selfhelp books you can use to supplement the information in the guides. If you need further assistance If you have followed the recommendations in this chapter and are still having problems, you may need additional technical assistance. This section contains the steps to take to ask for help.
If Something Goes Wrong If you need further assistance Contacting Toshiba If you still need help and suspect that the problem is hardware-related, Toshiba offers a variety of resources to help you. To stay current on the most recent software and hardware options for your computer, and for other product information, be sure to regularly check the Toshiba Web site at accessories.toshiba.com. Toshiba voice contact Before calling Toshiba, make sure you have: ❖ Your computer’s model and model number.
If Something Goes Wrong Other Toshiba Internet Web sites 195 Other Toshiba Internet Web sites toshiba.com Worldwide Toshiba corporate site computers.toshiba.com Marketing and product information in the USA www.toshiba.ca Canada www.toshiba-Europe.com Europe www.toshiba.co.jp/index.htm Japan http://servicio.toshiba.com Mexico and all of Latin America Toshiba’s worldwide offices Australia Toshiba (Australia) Pty.
If Something Goes Wrong Toshiba’s worldwide offices Latin America and Caribbean Toshiba America Information Systems 9740 Irvine Blvd. Irvine, California 92618 USA Mexico Toshiba de México S.A. de C.V. Sierra Candela No.111, 6to. Piso Col. Lomas de Chapultepec. CP 11000 Mexico, DF. 800-457-7777 (within the US) 949-859-4273 (outside of the US this call may incur long-distance charges) Spain Toshiba Information Systems (España) S.A.
Appendix A Hot Keys Hot keys are keys that, when pressed in combination with the Fn key, turn system functions on and off. Hot keys have a legend on or above the key indicating the option or feature the key controls. Volume Mute Fn + This hot key enables/disables volume mute on your computer. When volume mute is enabled, no sound will come from the speakers or headphones. Instant password security F1 Fn + This hot key blanks the display.
Hot Keys Instant password security make the display’s content reappear, if no password is set for the current user. With a password The Fn + F1 key combination turns off the display and activates instant security. If you set a blank screen saver, pressing the Fn + F1 key combination to activate instant security will cause the screen to go blank. Using the pointing device or any key will make the display’s content reappear.
Hot Keys Power usage mode 199 To set up a password with a screen saver, go to Windows® XP Help for instructions: 1 Click Start, Help and Support. 2 In the Search field, type password screen saver. 3 Press Enter. 4 Click the Protect your files with a screen saver password link located under the suggested topics. Follow the steps listed in the Windows® Help to set up your password-protected screen saver.
Hot Keys Standby mode Standby mode Fn + This hot key puts the computer into Standby mode. ❖ A message box is displayed by default to confirm that the computer is going into Standby mode. This message box can be set so it does not display. Sample Standby confirmation box ❖ For more information about Standby mode, please see “Using Standby” on page 112. 5.375 x 8.375 ver 2.
Hot Keys Hibernation mode 201 Hibernation mode Fn + This hot key puts the computer into Hibernation mode. ❖ If Hibernation mode is enabled (the default) a message box is displayed by default to confirm the computer is going into Hibernation mode. The message box can be set so it does not display. Sample Hibernation confirmation box ❖ If Hibernation mode is disabled, this hot key will not respond. For more information on Hibernation mode, see “Using Hibernation” on page 108. 5.375 x 8.375 ver 2.
Hot Keys Display modes Display modes Fn + This hot key cycles through the power-on display options. The display modes are: ❖ Built-in display panel only ❖ Built-in display panel and external monitor simultaneously ❖ External monitor only In order to use a simultaneous mode, you must set the resolution of the internal display panel to match the resolution of the external display device. Display brightness Fn + The Fn + F6 hot key decreases the screen brightness.
Hot Keys Disabling or enabling the TouchPad 203 Disabling or enabling the TouchPad This hot key enables/disables the TouchPad. Fn + To use the TouchPad, see “Disabling or enabling the TouchPad” on page 56. Sample disable and enable TouchPad windows Keyboard hot keys F10 Fn + Fn + This hot key turns the cursor control overlay on and off. F11 This hot key turns the numeric overlay on and off. F12 + off.
Appendix B Power Cable Connectors Your notebook computer features a universal power supply you can use worldwide. This appendix shows the shapes of the typical AC power cable connectors for various parts of the world. USA and Canada United Kingdom UL approved CSA approved BS approved Australia Europe AS approved VDA approved NEMKO approved 204 5.375 x 8.375 ver 2.
Appendix C Using ConfigFree™ with your Toshiba Computer ConfigFree™ is a set of utilities that makes it easy to control communication devices and network connections. ConfigFree also lets you identify communication problems and create profiles for easy switching between locations and communication networks. The ConfigFree utilities include the following: ❖ Connectivity Doctor—The Connectivity Doctor utility is used to analyze network connections and fix networking problems with your notebook computer.
Getting Started Getting Started This section contains information about the ConfigFree main screen, and how to start and setup ConfigFree. For more detailed information on setting up and using ConfigFree, see the Help File included in the application. Starting ConfigFree To start ConfigFree, be sure the computer has a wired or wireless connection.
ConfigFree Utilities 207 Wireless LAN Bluetooth Connectivity Doctor Profiles Sample ConfigFree Launcher ConfigFree Utilities Connectivity Doctor The Connectivity Doctor lets you analyze your network connections and fix network-connection problems. Using Connectivity Doctor, you can view detailed network information by simply moving the mouse pointer.
ConfigFree Utilities Sample Connectivity Doctor screen Moving the mouse pointer over a wired or wireless network device icon displays information about the device, such as its IP address, subnet mask, and MAC address. A wireless network device also shows information such as the network SSID and the device’s Wired Equivalent Privacy (WEP) key settings. Sample viewing device information 5.375 x 8.375 ver 2.
ConfigFree Utilities 209 If a problem, or potential problem, is detected, a triangle containing an exclamation point appears in the Connectivity Doctor screen and an orange frame describes the relevant location. You can then view a possible cause and solution for the problem by clicking the exclamation point.
ConfigFree Utilities Search for Wireless Devices The Search for Wireless Devices utility searches for wireless LAN devices and Bluetooth devices currently used in the neighborhood, and displays information about them on a virtual map. To search for wireless devices: 1 Click the icon in the system tray. 2 Click Search for Wireless Devices. A virtual map appears with a graphical representation of the wireless devices that have been detected.
ConfigFree Utilities 211 Sample viewing Wi-Fi devices The following screen shows an example of Bluetooth devices that are detected. As with the Wi-Fi screen, moving the mouse pointer over a device icon displays information about the device. Sample viewing Bluetooth devices You can connect to devices shown on the Bluetooth map: 1 Click the icon of a Bluetooth device. 5.375 x 8.375 ver 2.
ConfigFree Utilities 2 Click your own computer at the center of the map. 3 Configured devices are automatically connected. Devices not yet configured launch the Add New Connection Wizard, where you can configure and connect to the device. Profile Settings The Profile Settings utility lets you save network settings in “profiles.” ConfigFree profiles are useful for easily switching network settings and devices.You can switch network settings simply by selecting the profile with the desired settings.
ConfigFree Utilities 213 ❖ Personal firewall settings for Internet connections. ❖ Dial-up connection settings for the default connection. ❖ File and printer sharing settings. ❖ Printer settings for the default printer. To create a profile: 1 Click the icon in the system tray. 2 Move the pointer to Profile. 3 Click Add. The Add Profile screen appears. 4 Select Capture and click OK. The Add Profile screen appears. 5 Enter the name of the profile you want to create.
ConfigFree Utilities Sample Add Profile screen NOTE The online help provides real-world examples of setting up profiles for different networking environments. After you set up one or more profiles, you can check their settings and fine-tune them as necessary. Profiles can also be imported and exported. This feature is useful when transferring profile settings to other computers. For more information about modifying, importing, and exporting profiles, refer to the online help.
ConfigFree Utilities 215 To connect to a Toshiba Wireless Projector: 1 Click the icon in the system tray. 2 Move the mouse pointer to Toshiba Wireless Projector (DPJ), then click Connect. Launching Quick Connect prevents you from using the network to connect to a Toshiba Wireless Projector when the wireless LAN Configuration is set to Ad hoc. If you are connected to an access point, the connection is broken and reestablished later.
ConfigFree Utilities Sample Projector icon when connected with Quick Connect If the wireless mode for the wireless setting is set for 5 GHz (802.11a), Quick Connect changes this mode to 2.4 GHz (802.11b) and then connects to the projector. The wireless LAN configuration returns to the settings that were last used before the Quick Connect function was started: ❖ If the Toshiba Wireless Projector utility is closed.
Using the Automatic Switch 217 Using the Automatic Switch The Automatic Switch feature allows the computer to automatically switch profiles the next time it is powered on. This feature is particularly useful if you want your computer to automatically switch from the network configuration you use in your office to the one you use at home. The Auto Switch feature contains options for automatically switching between wired and wireless devices.
Semi-Automatic Switch Feature Semi-Automatic Switch Feature The Semi-Automatic feature alerts you when the computer connects to a Service Set Identifier (SSID) stored in a profile, When the computer connects to the designated SSID, a notification window appears. You can then click this window to connect using the settings specified in the profile. To use the Semi-Automatic Switch feature: 1 Right-click the icon in the system tray. 2 Click Auto Switch. The Auto Switch dialog box appears.
Glossary TECHNICAL NOTE: Some features defined in this glossary may not be available on your computer. Acronyms The following acronyms may appear in this user’s guide.
Glossary DMA direct memory access DIMM dual inline memory module DOS disk operating system DPI dots per inch DSTN dual supertwist nematic DVD digital versatile (or video) disc DVD-ROM digital versatile (or video) disc read-only memory ECP enhanced capabilities port EPROM erasable programmable read-only memory FAT file allocation table FCC Federal Communications Commission GB gigabyte HDD hard disk drive HTML Hypertext Markup Language IEEE Institute of Electrical and Electron
Glossary 221 RAM random access memory RFI radio frequency interference ROM read-only memory RTC real-time clock SCSI small computer system interface SDRAM synchronous dynamic random access memory SRAM static random access memory SVGA super video graphics adapter TFT thin film transistor USB universal serial bus URL uniform resource locator WAN wide area network www World Wide Web Terms The following terms may appear in this user’s guide.
Glossary application — A computer program that you use to perform tasks of a specific type. Applications include word processors, spreadsheets, and database management systems. See also program. B backup — A copy of a file, usually on a removable disk, kept in case the original file is lost or damaged. basic input/output system (BIOS) — See BIOS. baud rate — The speed at which a communication device, such as a printer or modem, transmits information.
Glossary 223 byte — A sequence of eight bits. A byte is the smallest addressable unit of data. See also bit, gigabyte, kilobyte, megabyte. C cache — A section of very fast memory in which frequently used information is duplicated for quick access. Accessing data from cache is faster than accessing it from the computer’s main memory. See also CPU cache, L1 cache, L2 cache. CD — An individual compact disc. See also CD-ROM.
Glossary controller — A device that controls the transfer of data from a computer to a peripheral device and vice versa. For example, disk drives, monitors, keyboards, and printers all require controllers. CPU — See central processing unit (CPU). CPU cache — A section of very fast memory residing between the CPU and the computer’s main memory that temporarily stores data and instructions the CPU will need to execute commands and programs. See also cache, L1 cache, L2 cache.
Glossary 225 disk — A round, flat piece of material that can be magnetically influenced to hold information in digital form, and used in the production of magnetic disks, such as diskettes and hard disks. Compare disc. See also diskette, hard disk. disk drive — The device that reads and writes information and programs on a diskette or hard disk. It rotates the disk at high speed past one or more read/write heads.
Glossary enable — To turn on a computer option. See also disable. executable file — A computer program that is ready to run. Application programs and batch files are examples of executable files. Names of executable files usually end with a .bat or .exe extension. extension — See file extension. external device — See device. F file — A collection of related information, saved on disk with a unique name. A file may be a program, information used by a program, or a document. See also document.
Glossary 227 ground — A conductor to which all components of an electric circuit are connected. It has a potential of zero (0) volts, is connected to the earth, and is the point of reference for voltages in the circuit. H hard disk — A storage device composed of a rigid platter or platters that can be magnetically coded with data. Hard disks hold much more information than diskettes and are used for long-term storage of programs and data.
K Glossary keyboard shortcut — A key or combination of keys that you use to perform a task instead of using a pointing device such as the TouchPad. kilobyte (KB) — A unit of data equal to 1024 bytes. See also byte. L L1 (level one) cache — Memory cache built into the processor to help improve processing speed. See also cache, CPU cache, L2 cache. L2 (level two) cache — Memory cache installed on the motherboard to help improve processing speed. It is slower than L1 cache and faster than main memory.
Glossary 229 microprocessor — See central processing unit (CPU). MIDI (Musical Instrument Digital Interface) — A standard for connecting musical instruments, synthesizers, and computers. The MIDI standard provides a way of translating music into a form computers can use, and vice versa. modem — Short for “modulator/demodulator.” A device that converts information from digital to analog and back to digital, enabling information to pass back and forth between digital computers and analog telephone lines.
Glossary operating system — A set of programs that controls how the computer works. Examples of operating systems are Windows® 98 Second Edition and Windows® 2000 operating systems. P palette — See color palette. parallel — Processes that occur simultaneously. In communications, it means the transmission of more than one bit of information at a time. On your computer, the parallel port provides a parallel communications interface between the computer and an appropriate device.
Glossary 231 properties — The attributes of an object or device. For example, the properties of a file include the file’s type, size, and creation date. R RAM (random access memory) — Volatile memory that can be written to as well as read. By volatile, we mean that information in RAM is lost when you turn off your computer. This type of memory is used for your computer’s main memory. See also memory. Compare ROM. random access memory — See RAM. read-only memory — See ROM. reboot — See boot, restart.
Glossary serial — Processes that occur one at a time. In communications, it means the transmission of one bit at a time sequentially over a single channel. On your computer, the serial port provides a serial interface between the computer and an appropriate device. Compare parallel. shortcut — See keyboard shortcut. software — See program. Compare hardware.
Glossary W 233 Web — See World Wide Web. Wi-Fi — A trademarked term by the Wireless Capability Ethernet Alliance which stands for Wireless Fidelity, and is another term for the communication protocol to permit an Ethernet connection using wireless communication components. World Wide Web (www) — The worldwide network of Web sites linked together over the Internet. A user of the Web can jump from site to site regardless of the location of the computer hosting the site. See also Internet. 5.375 x 8.
Index A AC adapter 48 AC power light 48, 50 accessories memory 62 alarms low battery 124 audio features 145 Auto-Run 98 avoiding injury 40 B battery alarms 124 caring for 128 changing 125 charge not lasting 178 charging 51, 75, 119 disposal 130 installing 125 light 50, 121 monitoring power 121 power usage mode 199 removing 125 button start 134 buttons CD controls 94 CD Player 98 CD/DVD controls 93 DVD-ROM or multi-function drive eject 93 primary control 56 secondary control 56 C cards PC 148 CD creating
running on battery power 116 setting up 46, 63 turning on 53 warning resume failure message CDs inserting 95 problem solving 185 channels DMA 172 IRQ 172 charging main battery 51, 119 checking device properties 174 cleaning CD or DVDs 101 computer 76 comfort chair 42 lighting 42 work habits 43 command Shut down 102 Turn Off 102 commands Hibernate 103 powering down 101 Standby 104 communications network connection 138 system resources 172 compact discs inserting 95 problem solving 185 removing 100 compu
TOSHIBA Touch and Launch 61 disabling/enabling TouchPad 56 Disk Defragmenter 183 disk drive corrupted/damaged data files 183 missing files/trouble accessing a disk 182 running slow 183 diskette drive 72 cannot insert a diskette 183 cannot read a diskette 184 external 72 display does not look normal/flickers 180 external monitor not working 181 external, adjusting 74 hot key 73 latch 52 screen is blank 179 display limitations 74 display panel opening 52 Display settings hot key 145 disposal information 2
file names 89 files backing up 80, 91 printing 90 restoring 91 saving 79, 88 Fn key assigning functions 154 Fn-esse 153 assigning keys 154 change/remove key assignments 156 drag-and-drop 154 keyboard 153 starting 153 using keyboard 155 viewing key assignments 156 function keys 82 H hard disk drive light 54 hardware conflicts 171 resolving 173 Help Windows XP 170 Hibernate restarting 112 using 108 Hibernation 103 Hibernation mode 76 methods 108 hot key disable/enable TouchPad 203 display modes 202 disp
J determining COM port 136 problem solving 191 resetting port to default settings jack RJ-11 138 137 K keyboard character keys 81 Ctrl, Fn, and Alt keys 82 cursor control overlay 84 external 68 Fn-esse 153 function keys 82 hot keys 203 not working 167, 179 numeric keypad overlay 83 overlay keys 83 unexpected characters 178 Windows special keys 82 L upgrading 137 module Wi-Fi Mini PC 140 monitor connecting 73 not working 180 mouse connecting 68 moving the computer 77 multi-function drive 145 cannot
modem default 136 not recognized 189 problem solving 187, 188 removing 149 replacing 150 PC Cards using 148 PCMCIA (Personal Computer Memory Card International Association) 148 Plug and Play 173 port COM 136 ports external diskette drive 72 power cable 50 cable connectors 204 computer will not start 167 monitoring 121 problem solving 177 taking care of your battery 128 Power Management 159 powering down 101 power mode creating new 161 customizing 161 power usage modes 123 power-on password 54 precaution
non-system disk or disk error 168, 183 PC Card 187 checklist 188 error occurs 189 hot swapping fails 189 not recognized 189 slot appears dead 188 Plug and Play 173 power and batteries 177 printer 190 program not responding 165 program not working properly 183 screen does not look right/flickers 180 system resources 172 trouble prevention 192 URL address not found 170 using Startup options 169 warning resume failure 168 Windows XP not working 168 Windows XP will not start 168 programs not running corr
speakers external 148 Stand by command 112 Stand by mode hot key 200 Standby 104 low battery 124 restarting 115 using 112 start button 134 starting a program 84 Run dialog box 86 Windows Explorer 85 Windows Start menu 85 starting up the computer from Standby 115 Startup menu problem solving 169 sticky key 152 stored data protection 2 System Setup 168 system tools 182 Disk Defragmenter 183 Error-checking 182 system tray 135 T taskbar 135 Toshiba Internet Web sites 195 Toshiba Accessories information 38
Windows Explorer 85 Windows Media Player 96 Windows Standby 75 Windows Start menu 85 Windows XP Help 170 Help and Support 171 problem solving 168 Windows XP Professional taskbar 135 Windows® XP Professional desktop 132 wireless interoperability 7 wireless networking 138 Wizards Add Printer 70 Dial-Up Networking Wizard 138 Z Zooming Utility 163 5.375 x 8.375 ver 3.