PORTÉGÉ M300 TOSHIBA PORTÉGÉ M300 Portable Personal Computer User’s Manual
User’s Manual Copyright © 2004 by TOSHIBA Corporation. All rights reserved. Under the copyright laws, this manual cannot be reproduced in any form without the prior written permission of TOSHIBA. No patent liability is assumed, with respect to the use of the information contained herein.
User’s Manual EU Declaration of Conformity This product is carrying the CE-Mark in accordance with the related European Directives. Responsible for CE-Marking is TOSHIBA Europe GmbH, Hammfelddamm 8, 41460 Neuss, Germany. The complete and official EU Declaration of Conformity can be found on TOSHIBA’s web site http://epps.toshiba-teg.com on the Internet.
User’s Manual CE compliance This product is labelled with the CE Mark in accordance with the related European Directives, notably Electromagnetic Compatibility Directive 89/ 336/EEC for the notebook and the electronic accessories including the supplied power adapter, the Radio Equipment and Telecommunications Terminal Equipment Directive 99/5/EEC in case of implemented telecommunication accessories and the Low Voltage Directive 73/23/EEC for the supplied power adapter.
User’s Manual Network Compatibility Statement This product is designed to work with, and is compatible with the following networks. It has been tested to and found to conform with the additional requirements conditional in EG 201 121.
User’s Manual Optical disc drive safety instructions Be sure to check the international precautions at the end of this section. Panasonic DVD-ROM&CD-R/RW UJDA765 ■ The DVD-ROM&CD-R/RW drive employs a laser system. To ensure proper use of this product, please read this instruction manual carefully and retain for future reference. Should the unit ever require maintenance, contact an authorized service location.
User’s Manual DVD Super Multi UJ-822 ■ The DVD Super Multi drive employs a laser system. To ensure proper use of this product, please read this instruction manual carefully and retain for future reference. Should the unit ever require maintenance, contact an authorized service location. ■ Use of controls, adjustments or the performance of procedures other than those specified may result in hazardous radiation exposure. ■ To prevent direct exposure to the laser beam, do not try to open the enclosure.
User’s Manual International precautions CAUTION: This appliance contains a laser system and is classified as a “CLASS 1 LASER PRODUCT.” To use this model properly, read the instruction manual carefully and keep this manual for your future reference. In case of any trouble with this model, please contact your nearest “AUTHORIZED service station.” To prevent direct exposure to the laser beam, do not try to open the enclosure.
User’s Manual OBS! Apparaten innehåller laserkomponent som avger laserstråining överstigande gränsen för laserklass 1. VAROITUS. Suojakoteloa si saa avata. Laite sisältää laserdiodin, joka lähetää näkymätöntä silmilie vaarallista lasersäteilyä. CAUTION: USE OF CONTROLS OR ADJUSTMENTS OR PERFORMANCE OF PROCEDURES OTHER THAN THOSE SPECIFIED IN THE OWNER’S MANUAL MAY RESULT IN HAZARDOUS RADIATION EXPOSURE.
User’s Manual x User’s Manual
PORTÉGÉ M300 Table of Contents Preface General Precautions Chapter 1 : Introduction Equipment checklist . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-1 Hardware . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-1 Software . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-2 Documentation . . . . . . . . . . . . . . . . .
Table of Contents Chapter 3 : Getting Started Setting up your work space . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3-1 General conditions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3-2 Placement of the computer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3-2 Seating and posture . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Table of Contents Media care . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . CD/DVDs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Floppy disks. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Sound System . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Table of Contents Chapter 6 : Power and Power-Up Modes Power conditions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6-1 Power indicators . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6-2 Battery indicators. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6-2 DC IN indicator . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Table of Contents CF (CompactFlash) card. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-5 Inserting a CF card . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-6 Removing a CF card . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-6 CF card care . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Table of Contents i.LINK (IEEE1394) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .9-17 Modem . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .9-17 LAN . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .9-18 Wireless LAN. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Table of Contents Appendix E : AC Power Cord and Connectors Certification agencies . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Table of Contents xviii User’s Manual
PORTÉGÉ M300 Preface Congratulations on your purchase of the PORTÉGÉ M300 computer. This powerful notebook computer provides excellent expansion capability, including multimedia devices, and it is designed to provide years of reliable, high-performance computing. This manual tells how to set up and begin using your PORTÉGÉ M300 computer. It also provides detailed information on configuring your computer, basic operations and care, using optional devices and troubleshooting.
Preface Chapter 4, Operating Basics, includes instructions on using the following devices: Touch Pad, USB floppy disk drive, optical media drives, sound system, modem, Wireless communication features, LAN. It also provides tips on care of the computer, floppy disks and CD/DVDs. Chapter 5, The Keyboard, describes special keyboard functions including the keypad overlay and hot keys.
Preface Key operation Some operations require you to simultaneously use two or more keys. We identify such operations by the key top symbols separated by a plus sign (+). For example, Ctrl + C means you must hold down Ctrl and at the same time press C. If three keys are used, hold down the first two and at the same time press the third.
Preface xxii User’s Manual
PORTÉGÉ M300 General Precautions TOSHIBA computers are designed to optimize safety, minimize strain and withstand the rigors of portability. However, certain precautions should be observed to further reduce the risk of personal injury or damage to the computer. Be certain to read the general precautions below and to note the cautions included in the text of the manual. Stress injury Carefully read the Safety Instruction Manual.
General Precautions PC card overheating Some PC cards can become hot with prolonged use. Overheating of a PC card can result in errors or instability in the PC card operation. Also be careful when you remove a PC card that has been used for a long time. Mobile phones Use of mobile phones can interfere with the audio system. Computer operation is not impaired but it is recommended that a distance of 30 cm be maintained between the computer and a mobile phone in use.
PORTÉGÉ M300 Chapter 1 Introduction This chapter provides an equipment checklist, and it identifies the computer’s features, options and accessories. Some of the features described in this manual may not function properly if you use an operating system that was not preinstalled by TOSHIBA. Equipment checklist Carefully unpack your computer. Save the box and packing materials for future use.
Introduction Software Microsoft® Windows XP Professional ■ The following software is preinstalled: ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ Microsoft® Windows XP Professional Microsoft Internet Explorer TOSHIBA Utilities TOSHIBA SD Memory Boot Utility DVD Video Player TOSHIBA TouchPad On/Off Utility TOSHIBA Power Saver TOSHIBA Mobile Extension TOSHIBA Assist TOSHIBA ConfigFree TOSHIBA Zooming Utility TOSHIBA PC Diagnostic Tool TOSHIBA Controls Online manual Documentation ■ PORTÉGÉ M300 Portable Personal Computer User
Introduction Features The computer uses TOSHIBA’s advanced Large Scale Integration (LSI), Complementary Metal-Oxide Semiconductor (CMOS) technology extensively to provide compact size, minimum weight, low power usage, and high reliability. This computer incorporates the following features and benefits: Processor Built-in The computer is equipped with an Intel® processor. ■ Intel® Pentium® M processor, which incorporates a 64 KB level 1 cache memory and a 2 MB level 2 cache memory.
Introduction Power Battery pack The computer is powered by one rechargeable lithium-ion battery pack. RTC battery The internal RTC battery backs up the Real Time Clock (RTC) and calendar. AC adaptor The AC adaptor provides power to the system and recharges the batteries when they are low. It comes with a detachable power cord. It encloses 2-pin or 3-pin plug type.
Introduction User’s Manual DVD-ROM&CD-R/RW drive Some models are equipped with a full-size, DVD-ROM&CD-R/RW drive module that lets you run CD/DVDs without using an adaptor. It reads DVD-ROMs at maximum 8 speed and CD-ROMs at maximum 24 speed. It writes CD-R at maximum 24 speed and CD-RW at maximum 24 speed.
Introduction Display The computer’s LCD display panel supports high-resolution video graphics. The LCD screen can be set at a wide range of viewing angles for maximum comfort and readability. Built-in 12.1” TFT LCD screen 16 M colors, with a resolution of 1024 horizontal × 768 vertical pixels XGA. Graphics controller Graphics controller maximizes display performance. Refer to Display Controller and Modes section in Appendix B for more information.
Introduction Infrared The serial infrared port is compatible with Infrared Data Association (IrDA 1.1) standards. It enables cableless 4 Mbps, 1.152 Mbps, 115.2 kbps, 57.6 kbps, 38.4 kbps, 19.2 kbps or 9.6 kbps data transfer with IrDA 1.1 compatible external devices. Slots PC card The PC card slot accommodates one Type II card. CF card This slot accommodates CompactFlash. You cannot use CompactFlash that does not conform to CompactFlash Association specifications.
Introduction Communications 1-8 Modem An internal modem provides capability for data and fax communication. It supports V.90 (V.92). The speed of data transfer and fax depends on analog telephone line conditions. It has a modem jack for connecting to a telephone line. Both of V.90 and V.92 are supported only in USA, Canada, UK, France, Germany and Australia. Only V.90 is available in other regions.
Introduction Wireless LAN Some computers in this series are equipped with a Wireless LAN mini-PCI card that is compatible with other LAN systems based on Direct Sequence Spread Spectrum/Orthogonal Frequency Division Multiplexing radio technology that complies with the IEEE 802.11 Standard (Revision A, B or G), and Turbo Mode. ■ Theoretical maximum speed: 54Mbps (IEEE802.11a, 802.11g) ■ Theoretical maximum speed: 11Mbps (IEEE802.
Introduction Security Security lock slot Connects an optional security lock to anchor the computer to a desk or other large object. Special features The following features are either unique to TOSHIBA computers or are advanced features, which make the computer more convenient to use. 1-10 TOSHIBA Assist button Press this button to launch an application automatically. The default is TOSHIBA Assist.
Introduction User’s Manual Instant security A hot key function blanks the LCD screen and disables the computer providing data security. Intelligent power supply A microprocessor in the computer’s intelligent power supply detects the battery’s charge and calculates the remaining battery capacity. It also protects electronic components from abnormal conditions, such as voltage overload from an AC adaptor. You can monitor remaining battery capacity. Use the Battery remaining item in TOSHIBA Power Saver.
Introduction Optical media drive power icon Use this to turn the power of the optical media drive on or off. Clicking on the optical media drive icon on the taskbar will turn the power of the optical media drive on or off. If the optical media drive power is off, the disc tray will not open even if the eject button is pushed. The power of the optical media drive can be turned on using the optical media drive icon.
Introduction Utilities This section describes preinstalled utilities and tells how to start them. For details on operations, refer to each utility’s online manual, help files or readme.txt files. TOSHIBA Power Saver To access this power savings management program, click start, click Control Panel, click Performance and Maintenance and select the TOSHIBA Power Saver icon.
Introduction RecordNow! Basic for TOSHIBA You can create CD/DVDs in several formats including audio CDs that can be played on a standard stereo CD player and data CD/DVDs to store the files and folders on your hard disk drive. This software can be used on a model with DVDROM&CD-R/RW drive and DVD Super Multi drive. TOSHIBA Assist TOSHIBA Assist is a graphical user interface that provides easy access to help and services. It is the default function launched by the TOSHIBA Assist button.
Introduction TOSHIBA Hotkey Utility for Display Devices This utility has the change of a display device, and the function to change display resolution. Press Fn + F5 to change the active display device. Press Fn + Space keys to change the display resolution. TOSHIBA SD This utility has the function which formats SD Memory Card Format memory card by SD standard format. TOSHIBA Acoustic Silencer This utility has the function to set up the speed (read) of CD/DVD drive.
Introduction Advanced Port Replicator III The Advanced Port Replicator III provides the ports available on the computer in addition to separate PS/2 mouse and PS/2 keyboard ports, a digital visual interface (DVI) port, i.LINK™ (IEEE1394) port, line-in jack and line-out jack, External monitor port, Universal Serial Bus port (USB2.0) × 4, LAN jack, Modem jack, Serial port, Parallel port. The PORTÉGÉ M300 does not support the DVI and i.LINK ports on the Advanced Port Replicator III.
PORTÉGÉ M300 Chapter 2 The Grand Tour This chapter identifies the various components of your computer. Become familiar with each component before you operate the computer. Certain notebook chassis are designed to accommodate all possible configurations for an entire product series. Your select model may not have all the features and specifications corresponding to all of the icons or switches shown on the notebook chassis, unless you have selected all those features.
The Grand Tour Off On Display latch This latch secures the LCD panel in its closed position. Push the latch to open the display. Microphone jack A 3.5 mm mini microphone jack enables connection of a three-conductor mini jack for monaural microphone input. Headphone jack A 3.5 mm mini headphone jack enables connection of stereo headphones. Volume control Use this dial to adjust the volume of the stereo speakers and the stereo headphones.
The Grand Tour External monitor port This external monitor port lets you connect an external video display. PC card slot The PC card slot can accommodate a Type II card. The slot supports 16-bit PC cards and CardBus PC cards. PC card eject button Press this button to eject a PC card from the PC card slot. Keep foreign objects out of the PC card slot. A pin or similar object can damage the computer’s circuitry. Security lock slot A security cable attaches to this slot.
The Grand Tour CF Card slot This slot accommodates CompactFlash. You cannot use CompactFlash that does not conform to CompactFlash Association specifications. CF card eject button Press this button to eject a CompactFlash Card from the CF card slot. Keep foreign objects out of the CF Card slot. A pin or similar object can damage the computer’s circuitry. SD card slot SD cards are used in a wide variety of external devices. This slot lets you transfer data from the device to your computer.
The Grand Tour Backside The following figure shows the computer’s backside. DC IN 15V jack LAN active indicator (orange) LAN jack Link indicator (green) The backside of the computer DC IN 15V jack The AC adaptor connects to this jack. Use only the model of AC adaptor that comes with the computer. Using the wrong adaptor can damage your computer. LAN jack This jack lets you connect to a LAN.
The Grand Tour Underside The following figure shows the underside of the computer. Make sure the display is closed before turning over your computer. Battery lock Battery pack Notches Battery release latch Docking Interface Memory module cover The underside of the computer Battery lock Slide this lock to release the battery pack for removal. Battery pack The battery pack powers the computer when the AC adaptor is not connected.
The Grand Tour Memory module cover This cover protects one memory module socket one or no module is preinstalled. Refer to the Memory expansion section in Chapter 8, Optional Devices . Front with the display open This section shows the computer with the LCD display panel open. Refer to the appropriate illustration for details. To open the display, push the display latch on the front of the LCD display panel and lift up. Position the LCD display panel at a comfortable viewing angle.
The Grand Tour Display hinge The display hinge holds the LCD display panel at easy-to-view angles. LCD screen The LCD screen displays high-contrast text and graphics. The computer’s XGA screen consists of 1024 × 768 pixels. Refer to Display Controller and Modes in Appendix B . When the computer operates on the AC adaptor the LCD screen’s image will be somewhat brighter than when it operates on battery power. The lower brightness level is intended to save battery power.
The Grand Tour User’s Manual TOSHIBA Presentation button Press this button to change internal display, simultaneous display, or multi-monitor display. The default setting is the simultaneous display on LCD and CRT with resolution of 1024 × 768. When you press this button twice, the display mode returns to single display on LCD only. Setting of multi-monitor display in Windows XP, computer changes its display mode to the multi-monitor display on LCD and CRT.
The Grand Tour System indicators LEDs beneath icons, light when various computer operations are in progress. DC IN Power Battery HDD Wireless SD card communication System indicators 2-10 DC IN The DC IN indicator glows in green when DC power is supplied from the AC power adaptor. If the adaptor’s output voltage is abnormal or if the power supply malfunctions, this indicator flashes orange. Power The Power indicator glows in green when the computer is on.
The Grand Tour Keyboard indicators The figures below show the positions of the keypad overlay indicators and the Caps Lock indicator. When the Arrow mode indicator glows the keypad overlay lets you control the cursor. When the Numeric mode indicator glows the keypad overlay lets you enter numbers. When the Caps Lock indicator glows the keyboard is in all-caps mode. Caps Lock indicator Caps Lock indicator Caps Lock This indicator glows green when the alphabet keys are locked in uppercase.
The Grand Tour USB floppy disk drive (optional) The optional USB floppy disk drive accommodates 1.44-megabyte or 720kilobyte floppy disks. USB connector Disk-In-Use Indicator Floppy disk slot Eject button USB floppy disk drive USB connector Insert this connector to the USB port of your computer. Disk-In-Use Indicator This indicator lights when the floppy disk is being accessed. Floppy disk slot Insert a floppy disk in this slot.
The Grand Tour Optical media drives One of the following optical media drives is installed in the computer: DVDROM&CD-R/RW drive or DVD Super Multi drive. An ATAPI interface controller is used for CD/DVD-ROM operation. When the computer is accessing a CD/DVD, an indicator on the drive glows. For information on loading and unloading discs refer to the Using optical media drives section in Chapter 4, Operating Basics.
The Grand Tour DVDs ■ DVD-R and DVD+R discs can be written only once. The recorded data cannot be erased or changed. ■ DVD-RW, DVD+RW and DVD-RAM discs can be recorded more than once.
The Grand Tour AC adaptor The AC adaptor converts AC power to DC power and reduces the voltage supplied to the computer. It can automatically adjust to any voltage from 100 to 240 volts and to a frequency of either 50 or 60 hertz, enabling you to use the computer in almost any country/region. To recharge the battery, simply connect the AC adaptor to a power source and the computer. Refer to Chapter 6, Power and Power-Up Modes, for details.
The Grand Tour Use only the AC adaptor supplied as an accessory. Other AC adaptors have different voltage and terminal polarities and use of them may produce heat and smoke or even result in fire or rupture.
PORTÉGÉ M300 Chapter 3 Getting Started This chapter provides basic information to get you started using your computer. It covers the following topics: ■ Setting up your work space — for your health and safety Be sure also to read the Safety Instruction Manual. This guide, which is included with the computer, explains product liability.
Getting Started General conditions In general, if you are comfortable, so is your computer, but read the following to make sure your work site provides a proper environment. ■ Make sure there is adequate space around the computer for proper ventilation. ■ Make sure the AC power cord connects to an outlet that is close to the computer and easily accessible. ■ The temperature should be 5 to 35 degrees Centigrade (41 to 95 degrees Fahrenheit) and the relative humidity should be 20 to 80 percent.
Getting Started Seating and posture The height of your chair in relation to the computer and keyboard as well as the support it gives your body are primary factors in reducing work strain. Refer to the following tips. Below eye level 90°angles Foot rest Posture and positioning of the computer ■ Place your chair so that the keyboard is at or slightly below the level of your elbow. You should be able to type comfortably with your shoulders relaxed. ■ Your knees should be slightly higher than your hips.
Getting Started Work habits A key to avoiding discomfort or injury from repetitive strain is to vary your activities. If possible, schedule a variety of tasks into your workday. If you must spend long periods at the computer, finding ways to break up the routine can reduce stress and improve your efficiency. ■ Sit in a relaxed posture. Good positioning of your chair and equipment as described earlier can reduce tension in your shoulders or neck and ease back strain. ■ Vary your posture frequently.
Getting Started ■ Use only the AC adaptor that came with the computer or an equivalent optional adaptor. Use of any other adaptors could damage your computer. TOSHIBA assumes no liability for any damage in such case. ■ Do not use a 3-pin to 2-pin conversion plug. ■ The supplied power cord conforms to safety rules and regulations in the region the product is bought and should not be used outside this region.
Getting Started 2. Connect the AC adaptor’s DC output plug to the DC IN 15V jack on the back of the computer. DC IN 15V jack Connecting the adaptor to the computer 3. Plug the power cord into a live wall outlet. The Battery and DC IN indicators on the front of the computer should glow. Opening the display The computer’s LCD display panel can be rotated in a wide range of angles for optimal viewing. 1. Push the display latch on the front of the computer to unlatch the display panel. 2.
Getting Started Turning on the power This section describes how to turn on the power. The Power button LED indicates the status. Refer to the Power indicator section in Chapter 6, Power and Power-Up Modes . ■ After you turn on the power for the first time, do not turn it off until you have set up the operating system. Refer to the section Starting up for the first time. ■ If the USB floppy disk drive is connected, make sure it is empty.
Getting Started Turning off the power The power can be turned off in one of the following modes: Shut down (Boot), Hibernation or Standby mode. Shut Down mode (Boot mode) When you turn off the power in Shut Down mode no data is saved and the computer will boot to the operating system’s main screen. 1. If you have entered data, save it to the hard disk or to a floppy disk. 2. Make sure all disk (disc) activity has stopped, then remove the CD/ DVDs or floppy disk. Make sure the HDD indicator is off.
Getting Started For the computer to shut down in hibernation mode, the hibernation feature must be enabled in two places: the Hibernate tab in Power Options and Setup Action tab in TOSHIBA Power Saver. Otherwise, the computer will shut down in Standby mode. If battery power becomes depleted, data saved in Standby mode will be lost. ■ You can return to your previous working environment immediately when you turn on the computer.
Getting Started Do not turn the computer or devices back on immediately. Wait a moment to let all capacitors fully discharge. Standby mode If you have to interrupt your work, you can turn off the power without exiting from your software. Data is maintained in the computer’s main memory. When you turn on the power again, you can continue working right where you left off. ■ When the AC adaptor is connected, the computer will go into Standby mode according to the settings in the TOSHIBA Power Saver utility.
Getting Started Executing standby You can also enable Standby by pressing Fn + F3. See Chapter 5, The Keyboard, for details. You can enter standby mode in one of three ways: 1. Click start, click Turn Off Computer and click Stand By. 2. Close the computer’s LCD display panel. This feature must be enabled. Refer to the Setup Action tab in TOSHIBA Power Saver Utility described in the Control Panel. Open Performance and Maintenance and open TOSHIBA Power Saver. 3. Press the power button.
Getting Started Restoring the preinstalled software Some models in this series are prepared for Hard Disk Recovery. These models will come without a Product Recovery optical media and a Tools & Utilities CD-ROM. You can restore the preinstalled software depending on the model you purchased. Restoring from Recovery HDD For models only with HDD Recovery installed. If preinstalled files are damaged, use the HDD Recovery installation to restore them.
Getting Started Restoring from the Recovery HDD About 2GB of hard disk space is reserved for recovery partition. When re-setting up your hard disk, do not change, delete or add partitions in a manner other than specified in the manual. Otherwise, space for software may be destroyed. In addition, if you use a third-party partitioning program to reconfigure partitions on your hard disk, it may become impossible to re-setup your computer. 1. Turn off your computer. 2.
Getting Started Restoring from the Product Recovery Media For models only with bundled Product Recovery optical media. If preinstalled files are damaged, use the Product Recovery DVD or the TOSHIBA Tools & Utilities CD-ROM to restore them. Restoring the complete system To restore the operating system and all preinstalled software, follow the steps below. When you reinstall the Windows operating system, the hard disk will be reformatted and all data will be lost.
PORTÉGÉ M300 Chapter 4 Operating Basics This chapter gives information on basic operations including using the Touch Pad, the USB floppy disk drive (optional), optical media drives, Sound System, Modem, Wireless communication features and LAN. It also provides tips on care of the computer, floppy disks and CD/DVDs. Using the Touch Pad To use the Touch Pad, simply touch and move your fingertip across it in the direction you want the on-screen pointer to go.
Operating Basics You can also tap the Touch Pad to perform functions similar to those of the left button. Click: Tap once Double-click: Tap twice Drag and drop: Tap to select the material you want to move. Leave your finger on the Touch Pad after the second tap and move the material. Using the USB floppy disk drive USB floppy disk drive connects to one of the computer’s USB ports. It accommodates 1.44-megabyte or 720-kilobyte floppy disks. Refer to Chapter 2, The Grand Tour, for more information.
Operating Basics Disconnecting USB floppy disk drive When you have finished using the USB floppy disk drive, follow the procedures below to disconnect it: 1. Wait for the indicator light to go out to make sure all floppy disk activity has stopped. If you disconnect the USB floppy disk drive or turn off the power while the computer is accessing the drive you may lose data or damage the floppy disk or the drive. 2. Click the Safely Remove Hardware icon on the Task Bar. 3.
Operating Basics Loading discs To load CD/DVDs, follow the steps below. 1. When the computer’s power is on, press the eject button to open the disc tray slightly. Eject Button Pressing the eject button 2. Grasp the disc tray gently and pull until it is fully opened. Disc tray Pulling the disc tray open 3. Lay the CD/DVD, label side up, in the disc tray.
Operating Basics When the disc tray is fully opened, the edge of the computer will extend slightly over the CD/DVD tray. Therefore, you will need to turn the CD/DVD at an angle when you place it in the disc tray. After seating the CD/DVD, however, make sure it lies flat. ■ Do not touch a laser lens and its circumference portion. Doing so could cause misalignment. ■ Prevent foreign objects from entering the drive.
Operating Basics 2. The CD/DVD extends slightly over the sides of the disc tray so you can hold it. Hold the CD/DVD gently and lift it out. Removing a CD/DVD 3. Push the center of the disc tray to close it. Press gently until it locks into place. How to remove CD/DVD when the disk tray will not open Pressing the eject button will not open the disc tray when the computer power is off.
Operating Basics Writing CDs on DVD-ROM&CD-R/RW drive The DVD-ROM&CD-R/RW drive lets you write as well as read CD-ROMs. Observe the precautions in this section to ensure the best performance for writing CDs. For information on loading and unloading CDs refer to the Using optical media drives section. ■ CD-R discs can be written to only once. CD-RW discs can be rewritten many times. ■ When the power of the optical media drive is off, the disc tray will not open even if the eject button is pushed.
Operating Basics TOSHIBA has confirmed the operation of CD-R and CD-RW media of the manufacturers above. Operation of other media cannot be guaranteed. ■ The actual number of rewrites to CD-RW is affected by the quality of the disc and the way it is used. ■ Be sure to connect the AC adaptor when you write or rewrite. ■ Be sure to close all other software programs except the writing software. ■ Do not run software such as a screen saver which can put a heavy load on the CPU.
Operating Basics Writing CD/DVDs on DVD Super Multi drive You can use the DVD Super Multi drive to write data to either CD-R/RW or DVD-R/-RW/+R/+RW/-RAM discs. The following applications for writing are preinstalled: RecordNow!, and DLA licensed by Sonic Solutions. InterVideo WinDVD Creator 2 Platinum, which is a product of InterVideo, Inc. ■ CD-R discs can be written to only once. CD-RW discs can be rewritten many times.
Operating Basics CD-R: TAIYO YUDEN CO., LTD. MITSUBISHI CHEMICAL CORPORATION RICOH Co., Ltd. Hitachi Maxell Ltd. CD-RW: (Multi-Speed and High-Speed) MITSUBISHI CHEMICAL CORPORATION RICOH Co., Ltd. CD-RW: (Ultra-Speed) MITSUBISHI CHEMICAL CORPORATION DVD-R: DVD Specifications for Recordable Disc for General Version 2.0 TAIYO YUDEN CO., LTD. PIONEER VIDEO CORPORATION Matsushita Electric Industrial Co., Ltd. DVD+R: MITSUBISHI CHEMICAL CORPORATION RICOH Co., Ltd.
Operating Basics This drive cannot use discs that allow writing faster than 2 speed (DVD-R, DVD-RW, DVD-RAM), 2.4 speed (DVD+R, DVD+RW). ■ If the disc is poor in quality, dirty or damaged, writing or rewriting errors may occur. Be careful to check the disc for dirt or damage before you use it. ■ The actual number of rewrites to CD-RW, DVD-RW, DVD+RW or DVD-RAM is affected by the quality of the disc and the way it is used. ■ There are two types of DVD-R discs: authoring and general use discs.
Operating Basics ■ CD-RW (Ultra Speed +) media is not available. If used, data may be lost or damaged. ■ Write from the computer's HDD to the CD/DVD. Do not try to write from shared devices such as a LAN server or any other network device. ■ Writing with software other than RecordNow! and InterVideo WinDVD Creator Platinum are not recommended. When writing or rewriting Please observe/consider the following when you write or rewrite to a CD-R/RW, DVD-R/-RW/-RAM or DVD+R/+RW disc.
Operating Basics ■ You cannot back up a CD-ROM or CD-R/RW to DVD-R/-RW or DVD+R/+RW using the “Exact Copy” function of RecordNow!. ■ You cannot back up DVD-ROM, DVD-Video or DVD-R/-RW or DVD+R/+RW to CD-R/RW using the “Exact Copy” function of RecordNow!. ■ RecordNow! cannot record in packet format. ■ You might not be able to use the “Exact Copy” function of RecordNow! to back up a DVD-R/-RW or DVD+R/+RW disc that was made with other software on a different DVD-R/-RW or DVD+R/+RW recorder.
Operating Basics DLA for TOSHIBA Note the following limitations when you use DLA: ■ This software supports only rewritable discs (DVD+RW, DVD-RW, and CD-RW). It does not support DVD+R, DVD-R, and CD-R discs that are not rewritable. ■ DLA does not support formatting a DVD-RAM disc and writing to it. They are performed by DVD-RAM Driver Software.
Operating Basics How to make a DVD-Video Simplified steps for making a DVD-Video from video data captured from a DV-Camcorder: 1. Click [Start]-[All Programs] - [InterVideo WinDVD Creator2] [InterVideo WinDVD Creator] to launch WinDVD Creator. 2. Click [Capture] button then capture the video data from the DV-Camcorder via IEEE1394. 3. Click [Edit] button then drag the video clips from [Video Library] tab to the edit track. 4. Click [Make Movie] button in the top bar. 5.
Operating Basics ■ While recording video to DVD or tape, please close all other programs. ■ Do not run software like a screen saver because it can put a heavy load on the CPU. ■ Do not run communication applications like a modem or a LAN. 2. Before recording the video to DVD ■ When you record to DVD disc, please use only discs recommended by the Drive manufacturer. ■ Do not set the working drive to a slow device like a USB 1.1 hard disk drive or it will fail to write DVD.
Operating Basics Media care This section provides tips on protecting data stored on your CD/DVDs and floppy disks. Handle your media with care. The following simple precautions will increase the lifetime of your media and protect the data stored on them: CD/DVDs 1. Store your CD/DVDs in the container they came in to protect them and keep them clean. 2. Do not bend the CD/DVD. 3. Do not write on, apply a sticker to, or otherwise mar the surface of the CD/DVD that contains data. 4.
Operating Basics Sound System This section describes audio controls including sound levels and power management. Volume Control The Volume Control utility lets you control the audio volume in Windows for both playback and recording. ■ To launch Volume Control for playback, click start, point to All Programs, point to Accessories, point to Entertainment and click Volume Control. ■ To launch Recording Control, click Options, point to Properties, choose Recording and click OK.
Operating Basics Modem This section describes how to connect and disconnect the internal modem to and from a telephone jack. The internal modem does not support voice functions. All data and fax functions are supported. ■ In case of a lightning storm, unplug the modular cable from the telephone jack. ■ Do not connect the modem to a digital telephone line. A digital line will damage the modem.
Operating Basics AutoRun Mode The Region Select utility starts automatically when you start up the operating system. Open the Dialing Properties dialog box after selecting region. The dialing properties dialog box will be displayed automatically after you select the region. Location list for region selection. A submenu appears displaying location information for telephony. Open dialog box, if the modem and Telephony Current Location region code do not match.
Operating Basics 2. Plug the other end of the modular cable into a telephone jack. Modular cable Modem jack Telephone jack Connecting the internal modem Do not pull on the cable or move the computer while the cable is connected. If you use a storage device such as an optical drive or HDD connected to a 16-bit PC card, you might experience the following modem problems: ■ Modem speed is slow or communication is interrupted. ■ Skips may occur in sound.
Operating Basics Wireless LAN The Wireless LAN is compatible with other LAN systems based on Direct Sequence Spread Spectrum /Orthogonal Frequency Division Multiplexing radio technology that complies with IEEE802.11 Wireless LAN standard (Revision A, B or G) and Turbo Mode. ■ Theoretical maximum speed: 54Mbps (IEEE802.11a, 802.11g) ■ Theoretical maximum speed: 11Mbps (IEEE802.
Operating Basics Bluetooth wireless technology Bluetooth™ wireless technology eliminates the need for cables between electronic devices such as desktop computers, printers and mobile phones. You cannot use the built-in Bluetooth functions and an optional Bluetooth SD card 3 simultaneously. Bluetooth wireless technology has the following features: Worldwide operation The Bluetooth radio transmitter and receiver operate in the 2.
Operating Basics Release Notes related to the BluetoothTM Stack for Windows® by TOSHIBA 1. Install: On Windows2000 or Windows XP, BluetoothTM Stack for Windows® by TOSHIBA does not need signature. 2. Fax application software: Regarding FAX application software, there are some software that you cannot use on this BluetoothTM Stack. 3. Multi User: On Windows XP, Multi user does not supported. When you use Bluetooth, you might not use Bluetooth another logon user.
Operating Basics Wireless communication Indicator The wireless communication indicator indicates the status of the wireless communication functions. Indicator status Indication Indicator off Wireless communication switch is set to off. Automatic power down because of overheating. Power malfunction Indicator glows Wireless communication switch is on. Wireless LAN or Bluetooth is turned on by an application.
Operating Basics Connecting LAN cable To connect the LAN cable, follow the steps below. ■ Connect the AC adaptor before connecting the LAN cable. The AC adaptor must remain connected during LAN use. If you disconnect the AC Adaptor while the computer is accessing a LAN, the system may hang up. ■ Do not connect any other cable to the LAN jack except the LAN cable. Otherwise, malfunctions or damage may occur. ■ Do not connect any power supplying device to the LAN cable that is connected to the LAN jack.
Operating Basics Cleaning the computer To help ensure long, trouble-free operation, keep the computer free of dust and use care with liquids around the computer. ■ Be careful not to spill liquids into the computer. If the computer does get wet, turn the power off immediately and let the computer dry completely before you turn it on again. ■ Clean the computer using a slightly damp (with water) cloth. You can use glass cleaner on the LCD display screen.
Operating Basics Heat dispersal To protect from overheating, the CPU has an internal temperature sensor. If the computer’s internal temperature rises to a certain level, the cooling fan is turned on or the processing speed is lowered. You can select whether to control the CPU temperature by turning on the fan first, then if necessary, lowering the CPU speed. Or, by lowering the CPU speed first, then if necessary, turning on the fan. Use the Cooling Method item of the Basic Setup tab in TOSHIBA Power Saver.
PORTÉGÉ M300 Chapter 5 The Keyboard The computer’s keyboard layouts are compatible with a 101/102-key enhanced keyboard. By pressing some keys in combination, all the 101/102-key keyboard functions can be executed on the computer. The number of keys on your keyboard depends on which country/region’s keyboard layout your computer is configured with. Keyboards for numerous languages are available.
The Keyboard Function keys: F1 … F12 The function keys (not to be confused with Fn) are the 12 keys at the top of your keyboard. These keys function differently from other keys. F1 through F12 are called function keys because they execute programmed functions when pressed. Used in combination with the Fn key, keys marked with icons execute specific functions on the computer. Refer to the section, Soft keys: Fn key combinations, in this chapter.
The Keyboard or Press Fn + F10 or Fn + F11 to access the integrated keypad. When activated, the keys with gray markings on the bottom edge become numeric keypad keys (Fn + F11) or cursor control keys (Fn + F10). Refer to the Keypad overlay section in this chapter for more information on how to operate these keys. The power on default for both settings is off. Press Fn + F12 (ScrLock) to lock the cursor on a specific line. The power on default is off.
The Keyboard Instant security: Press Fn + F1 to blank the screen to prevent others from accessing your data. To restore the screen and original settings, press any key or press the Touch Pad. If a screensaver password is registered, a dialog box will appear. Enter the screensaver password and click OK. If no password is set, the screen will be restored when you press any key or press the Touch Pad. Power save mode: Pressing Fn + F2 changes the power save mode.
The Keyboard Display selection: Press Fn + F5 to change the active display device. When you press these hot keys, a dialog box appears. Only selectable devices will be displayed. Hold down Fn and press F5 again to change the device. When you release Fn and F5, the selected device will change. If you hold down these hot keys for five seconds the selection will return to the internal LCD. Internal LCD screen Brightness: Pressing Fn + F6 decreases the LCD screen brightness in decrements.
The Keyboard If no wireless communication device is installed, no dialog box will appear. Touch Pad: Pressing Fn + F9 in a windows environment enables or disables the Touch Pad function. When you press these hot keys, the current setting will change and be displayed as an icon. LCD screen resolution selection: Press Fn + Space keys to change the LCD screen resolution.
The Keyboard Windows special keys The keyboard provides two keys that have special functions in Windows: Windows logo key activates the start menu and the other, the application key, has the same function as the secondary mouse button. This key activates the Windows start menu. This key has the same function as the secondary mouse button. Keypad overlay Your computer’s keyboard does not have an independent numeric keypad, but its numeric keypad overlay functions like one.
The Keyboard Numeric mode To turn on the Numeric mode, press Fn + F11. The Numeric mode indicator lights. Now try numeric data entry using the keys in the figure below. Press Fn + F11 again to turn off the overlay. The numeric keypad overlay Temporarily using normal keyboard (overlay on) While using the overlay, you can temporarily access the normal keyboard without turning off the overlay: 1. Hold Fn and press any other key. All keys will operate as if the overlay were off. 2.
The Keyboard Temporarily changing modes If the computer is in Numeric mode, you can switch temporarily to Arrow mode by pressing a shift key. If the computer is in Arrow mode, you can switch temporarily to Numeric mode by pressing a shift key. Generating ASCII characters Not all ASCII characters can be generated using normal keyboard operation. But, you can generate these characters using their ASCII codes. With the overlay on: 1. Hold down Alt. 2. Using the overlay keys, type the ASCII code. 3.
The Keyboard 5-10 User’s Manual
PORTÉGÉ M300 Chapter 6 Power and Power-Up Modes The computer’s power resources include the AC adaptor, battery pack and internal batteries. This chapter gives details on making the most effective use of these resources including charging and changing batteries, tips for saving battery power, and power up modes.
Power and Power-Up Modes Power conditions continued Power on AC adaptor not connected Battery charge is above low battery trigger point • Operates • LED: Battery off DC IN off Battery charge is below low battery trigger point • Operates • LED: Battery flashes orange DC IN off Battery charge is exhausted Computer goes into resume mode shuts down No battery installed • Cannot operate • LED: Battery off DC IN off Power off (no operation) Power indicators As shown in the above table, the Battery, DC
Power and Power-Up Modes DC IN indicator Check the DC IN indicator to determine the power status with the AC adaptor connected: Green Indicates the AC adaptor is connected and supplying proper power to the computer. Flashing orange Indicates a problem with the power supply. Plug the AC adaptor into another power outlet. If it still does not operate properly, contact your dealer. No light Under any other conditions, the indicator does not light.
Power and Power-Up Modes ■ The battery pack is a lithium ion battery, which can explode if not properly replaced, used, handled or disposed of. Dispose of the battery as required by local ordinances or regulations. Use only batteries recommended by TOSHIBA as replacements. ■ Do not remove the battery pack while the computer is in Standby mode. Data is stored in RAM, so if the computer loses power it will be lost.
Power and Power-Up Modes Real Time Clock (RTC) battery The Real Time Clock (RTC) battery provides power for the internal real time clock and calendar. It also maintains the system configuration. If the RTC battery becomes completely discharged, the system loses this data and the real time clock and calendar stop working. The following message appears when you turn on the power: S **** RTC battery is low or CMOS checksum is inconsistent **** Press [F1] key to set Date/Time.
Power and Power-Up Modes 3. Never short-circuit the battery pack by contacting the terminals with a metal object. A short-circuit can cause fire or otherwise damage the battery pack and possibly cause injury. To avoid accidental short-circuit, always wrap the battery pack in plastic and cover the terminals with electrical tape when storing or disposing of the battery pack. 4. Never puncture the battery pack with a nail or other sharp object. Never strike it with a hammer or other object. Never step on it.
Power and Power-Up Modes Caution 1. Never continue to use a battery pack after its recharging capacity has become impaired, or after the display of a warning message indicating that the battery pack’s power is exhausted. Continued use of an exhausted or impaired battery pack could cause the loss of data. 2. Never dispose of battery packs with normal trash. Bring them to your TOSHIBA dealer or to another recycling center to save resources and prevent environmental damage.
Power and Power-Up Modes Charging the batteries When the power in the battery pack becomes low, the Battery indicator flashes orange indicating that only a few minutes of battery power remain. If you continue to use the computer while the Battery indicator flashes, the computer enables Hibernation mode (so you don’t lose data) and automatically turns off.
Power and Power-Up Modes Battery charging notice The battery may not charge right away under the following conditions: ■ The battery is extremely hot or cold. If the battery is extremely hot, it might not charge at all. To ensure the battery charges to its full capacity, charge the battery at room temperature of 10° to 30°C (50° to 88°F). ■ The battery is nearly completely discharged. Leave the AC adaptor connected for a few minutes and the battery should begin charging.
Power and Power-Up Modes Maximizing battery operating time A battery’s usefulness depends on how long it can supply power on a single charge. How long the charge lasts in a battery depends on: ■ How you configure the computer (for example, whether you enable battery-power saving options). The computer provides a battery save mode, which can be set in TOSHIBA Power Saver, to conserve battery power.
Power and Power-Up Modes Extending battery life To maximize the life of your battery pack: ■ At least once a month, disconnect the computer from a power source and operate it on battery power until the battery pack fully discharges. Before doing so, follow the steps below. 1. Turn off the computer’s power. 2. Disconnect the AC adaptor and turn on the computer’s power. If it does not turn on go to step 4. 3. Operate the computer on battery power for five minutes.
Power and Power-Up Modes Replacing the battery pack When the battery pack reaches the end of its operating life you will need to install a new one. The life of the battery pack is generally about 500 recharges. If the Battery indicator flashes orange shortly after fully recharging the battery, the battery pack needs to be replaced. You might also replace a discharged battery pack with a charged spare when you are operating your computer away from an AC power source.
Power and Power-Up Modes 6. Slide and hold the battery release latch to free the battery pack for removal, then slide out the battery pack. Battery lock Battery pack Battery release latch Releasing the battery pack 7. Return your computer to the upright position. For environmental reasons, do not throw away a spent battery pack. Please return spent battery packs to your TOSHIBA dealer. Installing the battery pack To install a battery pack, follow the steps below.
Power and Power-Up Modes 5. Secure the battery pack lock. Check the battery lock was changed to the lock position ( ). Battery pack Battery lock Securing the battery cover 6. Return your computer to the upright position. TOSHIBA Password Utility The TOSHIBA Password Utility provides two levels of password security: User and Supervisor. Passwords set in TOSHIBA Password Utility are different from the Windows password.
Power and Power-Up Modes User Password field ■ Set (button) Click this button to register a password of up to 50 characters. After a password is set, you will be prompted to enter it when you start the computer. ■ After you set the password, a dialog box will be displayed asking whether you want to save it to a floppy disk or other media. If you forget the password, you can open the password file on another computer. Be sure to keep the media in a safe place.
Power and Power-Up Modes ■ Disable (button) Click this button to invalidate the token. You cannot revalidate old tokens, but you can use the same SD cards to create new tokens. After using the token created for authentication, do not leave it inserted in the SD card slot, ensure that the token is removed from the slot and stored in a safe location.
Power and Power-Up Modes Power-up modes The computer has the following power-up modes: ■ Boot: Computer shuts down without saving data. Always save your work before you turn the computer off in boot mode. ■ Hibernation: Data in memory is saved to the hard disk. ■ Standby: Data is maintained in the computer’s memory. Refer also to the sections Turning on the power and Turning off the power in Chapter 3, Getting Started. Windows utilities You can specify the setting in TOSHIBA Power Saver.
Power and Power-Up Modes 6-18 User’s Manual
PORTÉGÉ M300 Chapter 7 HW Setup This chapter explains how to use TOSHIBA HW Setup program to configure your computer. TOSHIBA HW Setup lets you configure settings for General, Display, Boot Priority, Keyboard, CPU, LAN, Device Config, Parallel/Printer and USB. Accessing HW Setup To run HW Setup, click start, click Control Panel, click Printers and Other Hardware and select TOSHIBA HWSetup.
HW Setup General This window displays the BIOS version and contains two buttons: Default and About. Default Return all HW Setup values to the factory settings. About Display the HW Setup version. Setup This field displays BIOS Version and date. Display This tab lets you customize your computer’s display settings for either the internal LCD screen or for an external monitor. Power On Display Lets you use the display to be used when the computer is booted.
HW Setup HDD −> FDD −> CDROM −> LAN The looks for bootable files in the following order: HDD, floppy disk drive*1, CD-ROM*2 and LAN (Default). HDD −> CD-ROM −> LAN −> FDD The computer looks for bootable files in the following order: HDD, CD-ROM*2, LAN and floppy disk drive*1. FDD −> CD-ROM −> LAN −> HDD The computer looks for bootable files in the following order: floppy disk drive*1, CD-ROM*2, LAN and HDD.
HW Setup 3. Use the left/right cursor keys to highlight the boot device you want and press Enter. ■ If a supervisor password is set only, it is the following. ■ The menu above appear when you use the user password to start the computer (able to run HW Setup). ■ The menu above does not appear when you use the user password to start the computer (unable to run HW Setup). ■ If the supervisor and user password are set, it is the following.
HW Setup If you select Left Ctrl + Left Alt or Right Ctrl + Right Alt for this option, you cannot use the selected keys to reboot the computer in combination with the Del key. For example, if you select Left Ctrl + Left Alt, you must use Right Ctrl, Right Alt and Del to reboot the computer. Left Ctrl, Left Alt and Del cannot be used. Wake-up on Keyboard When this feature is enabled and the computer is in Standby mode, you can turn on the computer by pressing any key.
HW Setup LAN Wake-up on LAN This feature lets the computer’s power be turned on when it receives a wake-up signal from the LAN. Enabled Enables Wake-up on LAN. Disabled Disables Wake-up on LAN. (Default) Do not install or remove an optional memory module while Wake-up on LAN is enabled. The Wake-up on LAN function consumes power even when the system is off. Leave the AC adaptor connected while using this feature. Built-in LAN This feature enables or disables the Built-in LAN.
HW Setup Parallel Port Mode The options in this tab are ECP and Standard Bi-directional. ECP Sets the port type to Extended Capabilities Port (ECP). For most printers, the port should be set to ECP (Default). Standard Bi-directional This setting should be used with some other parallel devices. USB USB KB/Mouse Legacy Emulation Use this option to enable or disable USB KB/Mouse Legacy Emulation.
HW Setup 7-8 User’s Manual
PORTÉGÉ M300 Chapter 8 Optional Devices Optional devices can expand the computer’s capabilities and its versatility. This chapter describes connection or installation of the following devices, which are available from your TOSHIBA dealer: Cards/memory ■ ■ ■ ■ PC card SD card CF (CompactFlash) card Memory expansion Power devices ■ Battery pack ■ AC adaptor ■ Battery charger Peripheral devices ■ ■ ■ ■ ■ USB floppy disk drive External monitor i.
Optional Devices PC card The computer is equipped with a PC card slot that can accommodate a Type II card. Any PC card that meets industry standards (manufactured by TOSHIBA or other vendor) can be installed. The slot supports 16-bit PC cards, including PC card 16’s multifunction card and CardBus PC cards. CardBus supports the new standard of 32-bit PC cards. The bus provides superior performance for the greater demands of multimedia data transmission.
Optional Devices 5. Grasp the PC card and draw it out. PC card eject button PC card Removing the PC card SD card The computer is equipped with an SD card slot that can accommodate Secure Digital flash memory cards with various memory capacities. SD cards let you easily transfer data from devices, such as digital cameras and Personal Digital Assistants, that use SD card flash-memory. The cards have a high level of security and copy protection features. The slot cannot accommodate Multi Media cards.
Optional Devices Inserting an SD card To insert an SD card, follow the steps below. 1. Insert an SD card in the SD card slot. 2. Press gently to ensure a firm connection. SD card SD card slot Inserting an SD card Make sure the SD card is oriented properly before you insert it. Removing an SD card To remove an SD card, follow the steps below. 1. Open the Safely Remove Hardware icon on the Task Bar. 2. Point to SD card and click. 3. Push in the SD card and release it to pop the card out slightly. 4.
Optional Devices SD card care Set the write-protect switch to the lock position, if you do not want to record data. 1. Do not write to an SD card if the battery power is low. Low power could affect writing accuracy. 2. Do not remove an SD card while read/write is in progress. 3. The SD card is designed so that it can be inserted only one way. Do not try to force the SD card into the SD card slot. 4. Do not leave an SD card partially inserted in the slot.
Optional Devices Inserting a CF card To insert a CF card, follow the steps below. 1. Press the CF card eject button to extend it. 2. Press the extended eject button to pop the Dummy card out slightly. 3. Insert the CF card into the slot. 4. Press gently to ensure a firm connection. CF card Inserting a CF card Removing a CF card To remove a CF card, follow the steps below. 1. Open the Safely Remove Hardware icon on the Task Bar. 2. Point to CF card and click. 3.
Optional Devices CF card care 1. CF card used is consumable items, so make sure you back up important data. 2. Do not twist or bend CF card. 3. Do not expose CF card to liquids or store in humid areas or lay media close to containers of liquid. 4. Do not touch the metal part of a CF card or expose it to liquids or let it get dirty. 5. After using CF card, return it to its case. For more details on using CF card, see manuals accompanying the card.
Optional Devices Use a point size 0 Phillips screwdriver to remove and fasten the screws. Use of an incorrect screwdriver can damage the screw heads. Installing memory module Follow the steps below to install a memory module. 1. Set the computer to boot mode and turn the computer’s power off. Make sure the Power indicator is off. 2. Remove AC adaptor and all cables connected to the computer. 3. Turn the computer upside down and remove the battery pack.
Optional Devices ■ Be careful not to drop the screw inside the computer. ■ Do not touch the connectors on the memory module or on the computer. Debris on the connectors may cause memory access problems. 7. Seat the memory module cover and secure it with one screw. 8. Install the battery pack. Refer to Replacing the battery pack section in Chapter 6, Power and Power-Up Modes, for details. 9. Return your computer to the upright position. 10.
Optional Devices 7. Grasp the module by the sides and pull it out. ■ If you use the computer for a long time, the memory modules and the circuits located close to the memory modules will become hot. In this case, let them cool to room temperature before you replace them. ■ Do not touch the connectors on the memory module or on the computer. Debris on the connectors may cause memory access problems. Latches Removing the memory module 8. Seat the memory module cover and secure it with one screw. 9.
Optional Devices USB floppy disk drive The USB floppy disk drive module can be connected to the USB port. For details on connecting the USB floppy disk drive module, refer to Chapter 4, Operating Basics. External monitor An external analog monitor can be connected to the external monitor port on the computer. The computer supports VGA and XGA video modes. To connect a monitor, follow the steps below. 1. Turn the computer’s power off. 2. Connect the monitor cable to the external monitor port.
Optional Devices i.LINK (IEEE1394) i.LINK (IEEE1394) is used for high-speed data transfer for a range of compatible devices such as ■ Digital video cameras ■ Hard disk drives ■ MO drives ■ CD-RW drives i.LINK uses a four-pin connector, which does not carry electric current. External devices will need their own power supply. Precautions ■ Make a back-up of your data before transferring it to the computer. There is a possibility that the original data will be damaged.
Optional Devices Connecting 1. Make sure the connectors are properly aligned and plug the i.LINK (IEEE1394) cable into the computer. i.LINK (IEEE1394) connector i.LINK (IEEE1394) port Connecting the i.LINK(IEEE1394) cable into the computer 2. Plug the other end of the cable into the device. Note the following when you use i.LINK: ■ You may need to install drivers for your i.LINK devices. ■ Not all i.LINK devices have been tested. Therefore, compatibility with all i.LINK devices cannot be guaranteed.
Optional Devices Advanced Port Replicator IIl In addition to the ports available on the computer, the Advanced Port Replicator lll provides serial port and separate ports for PS/2 mouse and PS/2 keyboard. The Advanced Port Replicator connects directly to the docking interface on the underside of the computer. The AC adaptor connects the Advanced Port Replicator to a power source. The computer must be configured properly before connecting to a LAN.
Optional Devices Parallel printer A parallel printer port can be used only when Advanced Port Replicator III is connected. You can connect any standard Centronics-compatible parallel printer to your computer. All you need is an IBM PC™ parallel printer cable. Your dealer can supply one or you can purchase one at most computer stores. The cable’s connectors are designed so that it is impossible for you to connect them incorrectly. To connect a printer, follow these steps: 1. Turn off the computer’s power.
Optional Devices Security lock Security locks enable you to anchor your computer and optional Advanced Port Replicator III to a desk or other heavy object to help prevent unauthorized removal of the computer or Advanced Port Replicator III. The computer has a security lock slot on the left side and right side. Attach one end of a cable to a desk and the other end to the security lock slot. 1. Turn the computer so the left side (or right side) faces you. 2.
PORTÉGÉ M300 Chapter 9 Troubleshooting TOSHIBA designed the computer for durability. However, should problems occur, following the procedures in this chapter can help to determine the cause. All readers should become familiar with this chapter. Knowing what might go wrong can help prevent problems from occurring. Problem solving process Resolving problems will be much easier if you observe the following guidelines: ■ Stop immediately when you recognize a problem exists.
Troubleshooting Preliminary checklist Consider the simplest solution first. The items in this checklist are easy to fix and yet can cause what appears to be a serious problem. ■ Make sure you turn on all peripheral devices before you turn on the computer. This includes your printer and any other external device you are using. ■ Before you attach an external device, turn the computer off. When you turn the computer back on it recognizes the new device.
Troubleshooting Software Hardware The problems may be caused by your software or disk. If you cannot load a software package, the media may be damaged or the program might be corrupted. Try loading another copy of the software. If an error message appears while you are using a software package, check the software documentation. These documents usually include a problem solving section or a summary of error messages. Next, check any error messages in the OS documentation.
Troubleshooting S In Touch with Tomorrow TOSHIBA This message remains on the screen for a few seconds. If the self test is successful, the computer tries to load the operating system, depending on how the Boot Priority is set in the TOSHIBA HW Setup program. If any of the following conditions are present, the self test failed: ■ The computer stops and does not proceed to display information or messages except the TOSHIBA logo.
Troubleshooting AC power If you have trouble turning on the computer with the AC adaptor connected, check the DC IN indicator. Refer to Chapter 6, Power and Power-Up Modes for more information. Problem Procedure AC adaptor doesn’t power the computer (DC IN indicator does not glow green) Check the connections. Make sure the cord is firmly connected to the computer and a power outlet. Check the condition of the cord and terminals. If the cord is frayed or damaged, replace it.
Troubleshooting Problem Procedure Battery doesn’t charge when the AC adaptor is attached (Battery indicator does not glow in orange.) If the battery is completely discharged, it will not begin charging immediately. Wait a few minutes. If the battery still does not charge, make sure the outlet of the AC adaptor is supplying power. Test it by plugging in an appliance. Check whether the battery is hot or cold to the touch. If the battery is too hot or too cold, it will not charge properly.
Troubleshooting Real Time Clock Problem Procedure The following message is Displayed on the LCD screen: RTC battery is low or CMOS checksum is inconsistent. Press [F1] key to set Date/Time. The battery for RTC is wearing. Set the date and time in BIOS setup with the following steps: 1. Press F1 key. BIOS setup will boot up. 2. Set the date in System Date. 3. Set the time in System Time. 4. Press End key. Confirmation message will appear. 5. Press Y key.
Troubleshooting Internal LCD display panel Apparent LCD problems may be related to the computer’s setup. Refer to Chapter 7, HW Setup, for more information. Problem Procedure No display Press hotkeys Fn + F5 to change the display priority, to make sure it is not set for an external monitor. Markings appear on the They might have come from contact with the LCD screen. keyboard, Touch Pad. Try wiping the LCD screen gently with a clean dry cloth. If markings remain, use LCD screen cleaner.
Troubleshooting DVD-ROM&CD-R/RW drive For more information, refer to Chapter 4, Operating Basics. Problem Procedure You cannot access a CD/DVD in the drive Make sure the drive’s disc tray is securely closed. Press gently until it clicks into place. Check whether the drive power is on. If the power is off, click on the optical media drive icon in the task tray and turn on the power. Open the disc tray and make sure the CD/DVD is properly seated. It should lie flat with the label facing up.
Troubleshooting Problem Procedure Cannot write correctly If you have trouble writing, make sure you are observing the following precautions: ■ Use only media recommended by TOSHIBA. ■ Do not use the mouse or keyboard during writing. ■ Use only the software supplied with the computer for recording. ■ Do not run or start other software during writing. ■ Do not jar the computer during writing. ■ Do not connect/disconnect external devices or install/remove internal cards during writing.
Troubleshooting Check the type of CD/DVD you are using. The drive supports: DVD-ROM: DVD-ROM, DVD-Video CD-ROM: CD-DA, CD-Text, Photo CDTM (single/multi-session), CD-ROM Mode 1, Mode 2, CD-ROM XA Mode 2 (Form1, Form2), Enhanced CD (CD-EXTRA), Addressing Method 2 Check the region code on the DVD. It must match that on the DVD Super Multi drive. Region codes are listed in the Optical media drives section in Chapter 2, The Grand Tour.
Troubleshooting PC card Refer also to Chapter 8, Optional Devices . Problem Procedure PC card error occurs Reseat the PC card to make sure it is firmly connected. Make sure the connection between the external device and the card is firm. Check the card’s documentation. If problems persist, contact your dealer. CF card Refer also to Chapter 8, Optional Devices . Problem Procedure CF card error occurs Reseat the CF card to make sure it is firmly connected. Check the card's documentation.
Troubleshooting Pointing Device If you are using a USB mouse, also refer to the USB section in this chapter and to your mouse documentation. Touch Pad User’s Manual Problem Procedure On-screen pointer does not respond to Pad operation The system might be busy. If the pointer is shaped as an hourglass, wait for it to standby its normal shape and try again to move it. Double-tapping does not work Try changing the double-click speed setting in the mouse control utility. 1.
Troubleshooting USB mouse (optional) Problem Procedure On-screen pointer does not respond to mouse operation The system might be busy. If the pointer is shaped as an hourglass, wait for it to resume its normal shape and try again to move it. Make sure the mouse is properly connected to the USB port. 9-14 Double-clicking does not work Try changing the double-click speed setting in the mouse control utility. 1. Click start, click Control Panel, click Printers and Other Hardware and select Mouse icon.
Troubleshooting USB Refer also to your USB device’s documentation. Problem Procedure USB device does not work Check for a firm cable connection between the USB ports on the computer and the USB device. Make sure the USB device drivers are properly installed. Refer to your Windows XP documentation for information on checking the drivers. If you are using an operating system that does not support USB, you can still use a USB mouse and/or USB keyboard.
Troubleshooting Sound System Refer also to documentation for your audio devices. Problem Procedure No sound is heard Adjust the volume control dial. Check the software volume settings. Make sure the headphone connection is secure. If problems persist, contact your dealer. Check Windows Device Manager.
Troubleshooting i.LINK (IEEE1394) Problem Procedure i.LINK device does not function Make sure the cable is securely connected to the computer and to the device. Make sure the device’s power is turned on. Reinstall the drivers. Open the Windows Control Panel and double-click the Add Hardware icon. Follow the on-screen directions. Restart Windows. If problems persist, contact your dealer.
Troubleshooting Problem Procedure You cannot receive an incoming call Check the rings before auto answer setting in your communications application. You can also use the ATS0 command. If problems persist, contact your dealer. Problem Procedure Cannot access LAN Check for a firm cable connection between the LAN jack and the LAN HUB. Wake-up on LAN does not work Make sure the AC adaptor is connected. The Wake-up on LAN function consumes power even when the system is off.
Troubleshooting Bluetooth For more information on wireless communication, refer to Chapter 4, Operating Basics. Problem Procedure Cannot access Bluetooth device Make sure the computer’s wireless communication switch is set to on. Make sure the Bluetooth Manager is running and the power to the Bluetooth device is turned on. Make sure no optional Bluetooth PC card and Bluetooth SD card are installed in the computer.
Troubleshooting TOSHIBA support If you require any additional help using your computer or if you are having problems operating the computer, you may need to contact TOSHIBA for additional technical assistance. Before you call Some problems you experience may be related to software or the operating system, it is important to investigate other sources of assistance first. Before contacting TOSHIBA, try the following: ■ Review troubleshooting sections in the documentation for software and peripheral devices.
PORTÉGÉ M300 Appendix A Specifications This appendix summarizes the computer’s technical specifications. Physical Dimensions Size 286.0 (w) × 233.0 (d) × 28.9/32.
Specifications Built-in Modem Network control unit (NCU) Type of NCU AA Type of line Telephone line (analog only) Type of dialing Pulse Tone Control command AT commands EIA-578 commands Monitor function Computer’s speaker Communication specifications A-2 Communication system Data: Fax: Full duplex Half duplex Communication protocol Data ITU-T-Rec (Former CCITT) Bell Fax ITU-T-Rec (Former CCITT) V.21/V.22/V.22bis/V.32 /V.32bis/V.34/V.90 103/212A V.17/V.29/V.27ter /V.
PORTÉGÉ M300 Appendix B Display Controller and Modes Display controller The display controller interprets software commands into hardware commands that turn particular pels on or off. The controller is an advanced Video Graphics Array (VGA) that provides Extended Graphics Array (XGA) support for the internal LCD and external monitors. A high-resolution external monitor connected to the computer can display up to 2048 horizontal and 1536 vertical pixels at up to 64K mode.
Display Controller and Modes Table1 Video modes (VGA) Video mode Type Resolution Character matrix (pels) 0, 1 VGA Text 40 × 25 Characters 2, 3 VGA Text 0*, 1* LCD colors CRT colors Scanning frequency Vertical (Hz) 8×8 16 of 256K 16 of 256K 70 80 × 25 Characters 8×8 16 of 256K 16 of 256K 70 VGA Text 40 × 25 Characters 8 × 14 16 of 256K 16 of 256K 70 2*, 3* VGA Text 80 × 25 Characters 8 × 14 16 of 256K 16 of 256K 70 0+, 1+ VGA Text 40 × 25 Characters 9 × 16 16 of 256K 1
Display Controller and Modes Table1 Video modes (VGA) continued Video mode Type LCD colors CRT colors Scanning frequency Vertical (Hz) D VGA Grph 320 × 200 Pels 8×8 16 of 256K 16 of 256K 70 E VGA Grph 640 × 200 Pels 8×8 16 of 256K 16 of 256K 70 F VGA Grph 640 × 350 Pels 8 × 14 Mono Mono 70 10 VGA Grph 640 × 350 Pels 8 × 14 16 of 256K 16 of 256K 70 11 VGA Grph 640 × 480 Pels 8 × 16 2 of 256K 2 of 256K 60 12 VGA Grph 640 × 480 Pels 8 × 16 16 of 256K 16 of 256K 60
Display Controller and Modes Table 2 Video modes Resolution LCD colors CRT colors Vertical frequency (Hz) 640 × 480 256/256K 256/256K 60 75 85 100 800 × 600 256/256K 256/256K 60 75 85 100 1024 × 768 256/256K 256/256K 60 75 85 100 1280 × 1024 256/256K (Virtual) 256/256K 60 75 85 100 1400 × 1050 256/256K (Virtual) 256/256K 60 75 85 1600 × 1200 256/256K (Virtual) 256/256K 60 75 85 100 1920 × 1440 256/256K (Virtual) 256/256K 60 75 85 2048 × 1536 256/256K (Virtual) 256/256K 60
Display Controller and Modes Table 2 Video modes continued Resolution LCD colors CRT colors Vertical frequency (Hz) 640 × 480 64K/64K 64K/64K 60 75 85 100 800 × 600 64K/64K 64K/64K 60 75 85 100 1024 × 768 64K/64K 64K/64K 60 75 85 100 1280 × 1024 64K/64K (Virtual) 64K/64K 60 75 85 100 1400 × 1050 64K/64K (Virtual) 64K/64K 60 75 85 1600 × 1200 64K/64K (Virtual) 64K/64K 60 75 85 100 1920 × 1440 64K/64K (Virtual) 64K/64K 60 75 85 2048 × 1536 64K/64K (Virtual) 64K/64K 60 75 S
Display Controller and Modes Table 2 Video modes continued Resolution LCD colors CRT colors Vertical frequency (Hz) 640 × 480 16M/16M 16M/16M 60 75 85 100 800 × 600 16M/16M 16M/16M 60 75 85 100 1024 × 768 16M/16M 16M/16M 60 75 85 100 1280 × 1024 16M/16M (Virtual) 16M/16M 60 75 85 100 1400 × 1050 16M/16M (Virtual) 16M/16M 60 75 85 1600 × 1200 16M/16M (Virtual) 16M/16M 60 75 85 Some video modes are not supported in the following modes: the Internal/ External Simultaneous Display m
Display Controller and Modes Display settings 1. You cannot move from the [Settings] tab of [Display Properties] to the multi-monitor when you are using the display of the computer and an external CRT display or a TV at the same time. *The [Settings] tab is displayed in the following steps; 1) Open [Control Panel], click [Appearance and Themes]. 2) Click [display]. 3) Select [Settings] tab. Display Properties (1) ■ The way to move to multi-monitor 1) Press [Ctrl] + [Alt] + [F12] keys to make.
Display Controller and Modes 3) Select either Monitor (CRT display) or Television, then select Apply button, because the Primary Device is fixed into Notebook (the display of the computer). Intel(R) 82852/82855 GM/GME Graphics Controller Prope...(1) 2. Some reproduced DVD picture may not be displayed when the display of the computer and a CRT display are used at the same.
PORTÉGÉ M300 Appendix C Wireless LAN Card Specifications Form Factor Mini PCI Type III Compatibility ■ IEEE 802.11 Standard for Wireless LANS ■ Wi-Fi (Wireless Fidelity) certified by the Wi-Fi Alliance. The ‘Wi-Fi CERTIFIED’ logo is a certification mark of the Wi-Fi Alliance. Network Operating System ■ Microsoft Windows® Networking Media Access Protocol ■ CSMA/CA (Collision Avoidance) with Acknowledgment (ACK) Data Rate ■ Theoretical maximum speed: 54Mbps (IEEE802.11a/ IEEE802.
Wireless LAN Radio Characteristics Radio Characteristics of Wireless LAN Cards may vary according to: ■ Country/region where the product was purchased ■ Type of product Wireless communication is often subject to local radio regulations. Although Wireless LAN wireless networking products have been designed for operation in the license-free 2.4GHz and 5GHz band, local radio regulations may impose a number of limitations to the use of wireless communication equipment.
Wireless LAN Wireless IEEE 802.11 Channels Sets (Revision B and G) Frequency Range Channel ID 2400-2483.5 MHz 1 2412 2 2417 3 2422 4 2427 5 2432 6 2437 7 2442 8 2447 9 2452 10 2457*1 11 2462 12 2467*2 13 2472*2 *1 Factory-set default channels *2 Consult your Authorized Wireless LAN or TOSHIBA Sales office for information about the countries/regions in which these channels can be used.
Wireless LAN Wireless IEEE 802.
Wireless Channels Sets (Turbo Mode) Frequency Range Channel ID 2400-2483.5 MHz Note 6 2437 US only *3 *3 These channels are available to Atheros module type only. Wireless Channels Sets (Turbo Mode) Frequency Range Channel ID 5150-5850 MHz Note 42 5210 US only *4 50 5250 US only *4 58 5290 US only *4 152 5760 US only *4 160 5800 US only *4 *4 These channels are available to Atheros A/B/G combo type only.
C-6 User’s Manual
PORTÉGÉ M300 Appendix D Bluetooth wireless technology Interoperability BluetoothTM Cards from TOSHIBA are designed to be interoperable with any product with Bluetooth wireless technology that is based on Frequency Hopping Spread Spectrum (FHSS) radio technology, and is compliant to: ■ Bluetooth Specification Ver.1.2, as defined and approved by The Bluetooth Special Interest Group. ■ Logo certification with Bluetooth wireless technology as defined by The Bluetooth Special interest Group.
Bluetooth wireless technology Interoperability ■ Bluetooth wireless technology is a new innovative technology, and TOSHIBA has not confirmed compatibility of its BluetoothTM products with all computers and/or equipment using Bluetooth wireless technology other than TOSHIBA portable computers. Always use BluetoothTM Cards from TOSHIBA in order to enable wireless networks over two or more (up to a total of seven) TOSHIBA portable computers using these cards.
Bluetooth wireless technology Interoperability Bluetooth wireless technology and your Health The products with Bluetooth wireless technology, like other radio devices, emit radio frequency electromagnetic energy. The level of energy emitted by devices with Bluetooth wireless technology however is far much less than the electromagnetic energy emitted by wireless devices like for example mobile phones.
Bluetooth wireless technology Interoperability L ‘ utilisation de ce dispositif est autorisée seulement aux conditions suivantes: (1) il ne doit pas produire de brouillage et (2) l’ utilisateur du dispositif doit étre prét à accepter tout brouillage radioélectrique reçu, même si ce brouillage est susceptible de compromettre le fonctionnement du dispositif. The term “IC” before the equipment certification number only signifies that the Industry Canada technical specifications were met.
Bluetooth wireless technology Interoperability (The model with embedded Wireless LAN module: PA3234U-1MPC) Relevant transmitters include FCC IDs: CJ6UPA3234WL, CJ6UPA3232BT (The model with embedded Wireless LAN module: PA3297U-1MPC) Relevant transmitters include FCC IDs: CJ6UPA3297WL, CJ6UPA3232BT (The model with embedded Wireless LAN module: PA3299U-1MPC) Relevant transmitters include FCC IDs: CJ6UPA3299WLP, CJ6UPA3232BT (The model with embedded Wireless LAN module: PA3362U-1MPC) Relevant transmitters inc
Bluetooth wireless technology Interoperability Using BluetoothTM Card from TOSHIBA equipment in Japan In Japan, the frequency bandwidth of 2,400~2,483.5 MHz for second generation low-power data communication systems such as this equipment overlaps that of mobile object identification systems (premises radio station and specified low-power radio station). 1. Sticker Please put the following sticker on computer incorporating this product.
Bluetooth wireless technology Interoperability 3. TOSHIBA Direct PC Monday - Friday: Toll Free Tel : Direct Dial : FAX : 10:00-17:00 0120-13-1100 03-3457-5916 03-5444-9450 Device Authorization This device obtains the Technical Regulation Conformity Certification and the Technical Conditions Compliance Approval, and it belongs to the device class of radio equipment of low-power data communication system radio station stipulated in the Radio Law and the Telecommunications Business of Japan.
Approved Countries/Regions for use (BluetoothTM wireless technology) BluetoothTM Card from TOSHIBA equipment is approved to the radio standard by the countries/regions in the following table. Do not use this equipment except in the countries/regions in the following table.
PORTÉGÉ M300 Appendix E AC Power Cord and Connectors The power cord’s AC input plug must be compatible with the various international AC power outlets and the cord must meet the standards for the country/region in which it is used. All cords must meet the following specifications: Length: Minimum 2 meters Wire size: Minimum 0.75 mm2 Current rating: Minimum 2.5 amperes Voltage rating: 125 or 250 VAC (depending on country/region’s power standards) Certification agencies U.S.
In Europe, two conductors power cord must be VDE type, H05VVH2-F or H03VVH2-F and for three conductors power cord must be VDE type, H05VV-F. For the United States and Canada, two pin plug configuration must be a 2-15P (250V) or 1-15P (125V) and three pin plug configuration must be 6-15P (250V) or 5-15P (125V) as designated in the U.S. National Electrical code handbook and the Canadian Electrical Code Part II. The following illustrations show the plug shapes for the U.S.A.
PORTÉGÉ M300 Appendix F If your computer is stolen Always take care of your computer and try to prevent it from being stolen. You are the owner of a valuable technical device, which may be highly attractive to thieves, so please do not leave it unattended in a public place. To further help protect against theft, security cables can be bought for use with your notebook when it is being used at home or in the office.
If your computer is stolen TOSHIBA Theft Registration Send to: Fax number: TOSHIBA Europe GmbH Technical Service and Support Leibnizstr. 2 93055 Regensburg Germany +49 (0) 941 7807 921 Country stolen: Machine type: (e.g. TOSHIBA Pocket PC e350) Model number: (e.g. PSA50 YXT) Serial number: (e.g.
PORTÉGÉ M300 Glossary The terms in this glossary cover topics related to this manual. Alternate naming is included for reference.
Glossary IrDA: Infrared Data Association IRQ: interrupt request KB: kilobyte LCD: liquid crystal display LED: light emitting diode LSI: large scale integration MB: megabyte MS-DOS: Microsoft Disk Operating System OCR: optical character recognition (reader) PCB: printed circuit board PCI: peripheral component interconnect RAM: random access memory RGB: red, green, and blue ROM: read only memory RTC: real time clock SCSI: small computer system interface SIO: serial input/output SXGA+: super extended graphics
Glossary analog signal: A signal whose characteristics such as amplitude and frequency vary in proportion to (are an analog of) the value to be transmitted. Voice communications are analog signals. ANSI: American National Standards Institute. An organization established to adopt and define standards for a variety of technical disciplines. For example, ANSI defined the ASCII standard and other information processing requirements. antistatic: A material used to prevent the buildup of static electricity.
Glossary bus: An interface for transmission of signals, data or electric power. byte: The representation of a single character. A sequence of eight bits treated as a single unit; also the smallest addressable unit within the system. C cache memory: High speed memory which stores data that increases processor speed and data transfer rate. When the CPU reads data from main memory, it stores a copy of this data in cache memory.
Glossary compatibility: 1) The ability of one computer to accept and process data in the same manner as another computer without modifying the data or the media upon which it is being transferred. 2) the ability of one device to connect to or communicate with another system or component. components: Elements or parts (of a system) which make up the whole (system). computer program: A set of instructions written for a computer that enable it to achieve a desired result.
Glossary delete: To remove data from a disk or other data storage device. Synonymous with erase. device driver: A program that controls communication between a specific peripheral device and the computer. The CONFIG.SYS file contains device drivers that MS-DOS loads when you turn the computer on. dialog box: A window that accepts user input to make system settings or record other information. disk drive: The device that randomly accesses information on a disk and copies it to the computer’s memory.
Glossary escape: 1) A code (ASCII code 27), signaling the computer that what follows are commands; used with peripheral devices such as printers and modems. 2) A means of aborting the task currently in progress. escape guard time: A time before and after an escape code is sent to the modem which distinguishes between escapes that are part of the transmitted data, and escapes that are intended as a command to the modem. execute: To interpret and execute an instruction.
Glossary hardware: The physical electronic and mechanical components of a computer system: typically, the computer itself, external disk drives, etc. See also software and firmware. hertz: A unit of wave frequency that equals one cycle per second. hexadecimal: The base 16 numbering system composed of the digits 0 through 9 and the letters A, B, C, D, E, and F. host computer: The computer that controls, regulates, and transmits information to a device or another computer.
Glossary J jumper: A small clip or wire that allows you to change the hardware characteristics by electrically connecting two points of a circuit. K K: Taken from the Greek word kilo, meaning 1000; often used as equivalent to 1024, or 2 raised to the 10th power. See also byte and kilobyte. KB: See kilobyte. keyboard: An input device containing switches that are activated by manually pressing marked keys. Each keystroke activates a switch that transmits a specific code to the computer.
Glossary mode: A method of operation, for example, the boot mode, standby mode or the hibernation mode. modem: Derived from modulator/demodulator, a device that converts (modulates) digital data for transmission over telephone lines and then converts modulated data (demodulates) to digital format where received. monitor: A device that uses rows and columns of pixels to display alphanumeric characters or graphic images. See also CRT.
Glossary P parallel interface: Refers to a type of information exchange that transmits information one byte (8 bits) at a time. See also serial interface. parity: 1) The symmetrical relationship between two parameter values (integers) both of which are either on or off; odd or even; 0 or 1. 2) In serial communications, an error detection bit that is added to a group of data bits making the sum of the bits even or odd. Parity can be set to none, odd, or even.
Glossary restart: Resetting a computer without turning it off (also called “warm boot” or “soft reset”). See also boot. RGB: Red, green, and blue. A device that uses three input signals, each activating an electron gun for a primary additive color (red, green, and blue) or port for using such a device. See also CRT. RJ11: A modular telephone jack. RJ45: A modular LAN jack. ROM: Read Only Memory: A nonvolatile memory chip manufactured to contain information that controls the computer’s basic operation.
Glossary T terminal: A typewriter-like keyboard and CRT display screen connected to the computer for data input/output. TFT display: A liquid crystal display (LCD) made from an array of liquid crystal cells using active-matrix technology with thin film transistor (TFT) to drive each cell. Touch Pad: A pointing device integrated into the TOSHIBA computer palm rest. TTL: Transistor-transistor logic. A logic circuit design that uses switching transistors for gates and storage.
Glossary Glossary-14 User’s Manual
PORTÉGÉ M300 Index A AC adaptor 4 additional 15, 10 connecting 4 DC IN 15V jack 5 Advanced Port Replicator III 16, 14 ASCII characters 9 B Battery charging 8 extending life 11 indicator 10, 2 location 6 monitoring capacity 9 real time clock 4, 5 safety precautions 5 save mode 11 types 3 Battery charger 15, 10 Battery pack 4, 6 additional 10 replacing 12 Bluetooth 8, 23 problems 19 TOSHIBA Stack 13 Boot Priority 2 User’s Manual C CF card 7, 5 care 7 inserting 6 location of slot 3 problems 12 removing 6
Index DVD-ROM&CD-R/RW drive 5 location of slot 3 problems 9 using 3 writing 7 E Environment 1 Equipment checklist 1 Equipment setup general conditions 2 placement 2 Ergonomics lighting 3 seating and posture 3 work habits 4 F Floppy disk care 17 Fn + Ctrl (enhanced keyboard simulation) 3 Fn + Enter 3 Fn + Esc (sound mute) 3 Fn + F1 (instant security) 4 Fn + F10 (Arrow mode) 3 Fn + F11 (Numeric mode) 3 Fn + F12 (ScrLock) 3 Fn + F2 (power save mode) 4 Fn + F5 (display selection) 5 Fn + F6 (display brightnes
Index K Keyboard 6, 1 emulating enhanced keyboard 2 Fn Sticky key 6 Function keys F1...
Index Power button location 7 conditions 1 hibernation mode 8 indicators 2 panel on/off 11, 17 problems 4 shut down mode (boot mode) 8 standby mode 10 system auto off 17 turning off 8 turning on 7 Power-up modes 17 Printer parallel 6, 15 Problems AC power 5 Analyzing symptoms 2 Battery 5 Bluetooth 19 CF card 12 DVD Super Multi drive 10 DVD-ROM&CD-R/RW drive 9 External monitor 16 Hard disk drive 8 Hardware and system checklist 3 i.
Index T V TOSHIBA Assist 14 TOSHIBA Assist button 10 TOSHIBA ConfigFree 14 TOSHIBA Controls 13 TOSHIBA Mobile Extension 14 TOSHIBA PC Diagnostic Tool 14 TOSHIBA Power Saver 13 TOSHIBA Presentation button 10 TOSHIBA SD Memory Boot Utility 13 TOSHIBA Theft Registration 2 TOSHIBA Zooming Utility 13 Video modes 1 Video RAM 3 Volume control 2 W Wireless communication 21 indicator 10, 25 switch 9, 2, 24 Wireless LAN 9, 22, 1 problems 18 U USB 6 location 2, 3 problems 15 USB floppy disk drive 4 additional 11
Index Index-6 User’s Manual
