® Satellite M30X/M35X Series User’s Guide If you need assistance: ❖ Toshiba Global Support Centre Calling within the United States (800) 457-7777 Calling from outside the United States (949) 859-4273 For more information, see “If Something Goes Wrong” on page 155 in this guide.
Handling the cord on this product will expose you to lead, a chemical known to the State of California to cause birth defects or other reproductive harm. Wash hands after handling. Models: Satellite® M30X/M35X Series ReWritable CD/DVD Drives The computer system you purchased may include a ReWritable CD and/or DVD drive(s), among the most advanced data storage technologies available.
Critical Applications The computer you have purchased is not designed for any “critical applications.” “Critical applications” means life support systems, medical applications, connections to implanted medical devices, commercial transportation, nuclear facilities or systems or any other applications where product failure could lead to injury to persons or loss of life or catastrophic property damage.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: ❖ This device may not cause harmful interference. ❖ This device must accept any interference received, including interference that may cause undesired operation. Contact: Toshiba America Information Systems, Inc. 9740 Irvine Blvd. Irvine, CA 92618-1697 (949) 583-3000 Industry Canada requirement This Class B digital apparatus complies with Canadian ICES-003.
decimal point (e.g., 03 is a REN of 0.3). For earlier products, the REN is separately shown on the label. Connection to party line service is subject to state tariffs. Contact the state public utility commission, public service commission or corporation commission for information. Telephone Company Procedures The goal of the telephone company is to provide you with the best service it can.
provided may not be a 900 number or any other number for which charges exceed local or long-distance transmission charges.) In order to program this information into your fax transmission, refer to the fax software instructions installed on this computer. Alarm Equipment If your home has specially wired alarm equipment connected to the telephone line, ensure the installation of this equipment does not disable your alarm equipment.
NOTICE: The Ringer Equivalence Number (REN) assigned to each terminal device provides an indication of the maximum number of terminals allowed to be connected to a telephone interface. The termination on an interface may consist of any combination of devices subject only to the requirement that the sum of the Ringer Equivalence Numbers of all the devices does not exceed 5. 3 The standard connecting arrangement (telephone jack type) for this equipment is jack type(s): USOC RJ11C.
Wireless LAN and your Health Wireless LAN products, like other radio devices, emit radio frequency electromagnetic energy. The level of energy emitted by Wireless LAN devices however is far much less than the electromagnetic energy emitted by wireless devices like for example mobile phones. Because Wireless LAN products operate within the guidelines found in radio frequency safety standards and recommendations, TOSHIBA believes Wireless LAN is safe for use by consumers.
Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of this device.
Finnish: Dutch: French: Swedish: Danish: German: Valmistaja TOSHIBA Corp. Digital Media Network Company vakuuttaa täten että Radio LAN device tyyppinen laite on direktiivin 1999/5/EY oleellisten vaatimusten ja sitä koskevien direktiivin muiden ehtojen mukainen. Hierbij verklaart TOSHIBA Corp. Digital Media Network Company dat het toestel Radio LAN device in overeenstemming is met de essentiële eisen en de andere relevante bepalingen van richtlijn 1999/5/EG. Bij deze TOSHIBA Corp.
Spanish: Portuguese: Por medio de la presente TOSHIBA Corp. Digital Media Network Company declara que el Radio LAN device cumple con los requisitos esenciales y cualesquiera otras disposiciones aplicables o exigibles de la Directiva 1999/5/CE. TOSHIBA Corp. Digital Media Network Company declara que este Radio LAN device está conforme com os requisitos essenciais e outras disposições da Directiva 1999/5/CE. USA – Federal Communications Commission (FCC) This device complies with Part 15 of FCC Rules.
Caution: Radio Frequency Interference Requirements This device is restricted to indoor use due to its operation in the 5.15 GHz to 5.25 GHz frequency range. FCC requires this product to be used indoors for frequency range 5.15 GHz to 5.25 GHz to reduce the potential for harmful interference to co-channel Mobile Satellite systems. High power radars are allocated as primary users of the 5.25 GHz to 5.35 GHz and 5.65 GHz to 5.85 GHz bands.
2. Indication The indication shown below appears on this equipment. (1) (2) (3) 2.4DSOF4 (4) 1 2.4: This equipment uses a frequency of 2.4 GHz. 2 DS: This equipment uses DS-SS modulation. OF: This equipment uses OFDM modulation. 3 The interference range of this equipment is less than 40m. 4 This equipment uses a frequency bandwidth from 2,400 MHz to 2,483.5 MHz. It is possible to avoid the band of mobile object identification systems. 3.
Approval Number: D01-1128JP TELECOM ENGINEERING CENTER Approval Number: 03NY.A0018, 03GZDA0017 The following restrictions apply: ❖ ❖ ❖ Do not disassemble or modify the device. Do not install the embedded wireless module into other device. 5.17 GHz to 5.23 GHz for indoor use only Radio approvals for wireless devices NOTE The following information is dependent on what type of wireless device is in your computer.
Europe - Restrictions for use of 2.4 GHz Frequencies in European Community Countries België/ Belgique: Deutschland: France: Italia: Nederland: For private usage outside buildings across public grounds over less than 300m no special registration with IBPT/BIPT is required. Registration to IBPT/BIPT is required for private usage outside buildings across public grounds over more than 300m. For registration and license please contact IBPT/BIPT.
802.
❖ This device must not be operated in ad-hoc mode using channels in the 5 GHz bands in the European Community. Ad-hoc mode provides a direct communication between two client devices without a Wireless LAN Access Point. ❖ This device must be used with Access Points that have employed and activated a radar detection feature required for European Community operation in the 5 GHz bands.
802.11a (5 GHz) Australia Canada France Ireland Luxembourg Norway Switzerland Austria Denmark Germany Italy Netherlands Portugal UK Belgium Finland Greece Liechtenstein New Zealand Sweden USA Turbo Mode (5 GHz) Canada USA Approved Countries/Regions for use for the Intel® PRO/ Wireless LAN 2100 3B Mini PCI Adapter This equipment is approved to the radio standard by the countries/regions in the following table. Do not use this equipment except in the countries/regions in the following table.
Approved Countries/Regions for use for the Toshiba Mini PCI Wireless LAN Card This equipment is approved to the radio standard by the countries/regions in the following table. Do not use this equipment except in the countries/regions in the following table.
Bluetooth wireless technology is a new innovative technology, and TOSHIBA has not confirmed compatibility of its Bluetooth™ products with all PCs and/ or equipment using Bluetooth wireless technology other than TOSHIBA portable computers. Always use Bluetooth™ cards from TOSHIBA in order to enable wireless networks over two or more (up to a total of seven) TOSHIBA portable computers using these cards. Please contact TOSHIBA PC product support on Web site http://www.toshiba-europe.
community and result from deliberations of panels and committees of scientists who continually review and interpret the extensive research literature. In some situations or environments, the use of Bluetooth wireless technology may be restricted by the proprietor of the building or responsible representatives of the organization.
Caution: FCC Interference Statement This device complies with part15 of the FCC rules. Operation is subject to the following two conditions: ❖ This device may not cause harmful interference, and ❖ This device must accept any interference received, including interference that may cause undesired operation. Note that any changes or modifications to this equipment not expressly approved by the manufacturer may void the authorization to operate this equipment.
Article 17 Any use of low power radio frequency electric machinery shall not affect the aviation safety and interfere with legal communications. In event that any interference is found, the use of such electric machinery shall be stopped immediately, and reusing of such products can be resumed until no interference occurs after improvement. The legal communications mentioned in the above item refer to radio communications operated in accordance with telecommunication laws and regulations.
3 The interference range of this equipment is less than 10m. 4 This equipment uses a frequency bandwidth from 2,400 MHz to 2,483.5 MHz. It is impossible to avoid the band of mobile object identification systems. 3.
Location of the required label (Sample shown below. Location of the label and manufacturing information may vary.) This appliance contains a laser system and is classified as a “CLASS 1 LASER PRODUCT.” To use this model properly, read the user’s guide carefully and keep it for your future reference. In case of any trouble with this model, please contact your nearest “AUTHORIZED service station.” To prevent direct exposure to the laser beam, do not try to open the enclosure.
Notice The information contained in this manual, including but not limited to any product specifications, is subject to change without notice. TOSHIBA CORPORATION AND TOSHIBA AMERICA INFORMATION SYSTEMS, INC. (TOSHIBA) PROVIDES NO WARRANTY WITH REGARD TO THIS MANUAL OR ANY OTHER INFORMATION CONTAINED HEREIN AND HEREBY EXPRESSLY DISCLAIMS ANY IMPLIED WARRANTIES OF MERCHANTABILITY OR FITNESS FOR ANY PARTICULAR PURPOSE WITH REGARD TO ANY OF THE FOREGOING.
Computer disposal information This product contains mercury. Disposal of this material may be regulated due to environmental considerations. For disposal, reuse or recycling information, please contact your local government or the Electronic Industries Alliance at www.eiae.org. 5.375 x 8.375 ver 2.
Contents Introduction................................................................................ 35 This guide ...............................................................36 Safety icons ............................................................37 Other icons used...............................................38 Other documentation ..............................................38 Service options .......................................................39 Chapter 1: Getting Started..................
Contents 29 Using the computer for the first time ......................54 Opening the display panel .................................54 Your computer’s features and specifications ....55 Turning on the power........................................55 Using the TouchPad™.............................................56 Scrolling with the TouchPad™ ..........................56 Using the Scroll button .....................................57 Using the Control buttons .................................
Contents Windows® special keys.....................................80 Overlay keys......................................................81 Starting a program..................................................83 Starting a program from the Start menu...........83 Starting a program from Windows ® Explorer ...84 Starting a program from the Run dialog box ....85 Saving your work ....................................................86 Printing your work ..................................................
Contents 31 Chapter 3: Mobile Computing................................................ 111 Toshiba’s energy-saver design..............................111 Running the computer on battery power ..............111 Battery Notice .................................................112 Power management ........................................112 Using additional batteries ...............................113 Charging the batteries...........................................113 Charging the main battery..............
Contents Internet Service Providers...............................140 Connecting to the Internet .............................140 Surfing the Internet.........................................141 Internet features..............................................141 Uploading and downloading files from the Internet ....................................................142 Exploring video features .......................................142 Changing the display properties setting ................
Contents 33 Chapter 5: If Something Goes Wrong .................................. 155 Problems that are easy to fix ................................155 Problems when you turn on the computer............158 The Windows® operating system is not working ..159 Using Startup options to fix problems ............159 Internet problems ...........................................160 The Windows® XP operating system can help you ....................................................161 Resolving a hardware conflict ..
Contents Appendix A: Hot Keys..............................................................185 Volume Mute ........................................................185 Instant password security.....................................186 Without a password ........................................186 With a password .............................................186 Maintaining security when the battery is not fully charged .......................................187 Power usage mode ...........................
Introduction Welcome to the world of powerful and portable multimedia computers! With your new Toshiba notebook computer, your access to information can accompany you wherever you go. Your system comes with either the Microsoft® Windows® XP Home or Windows XP Professional operating system. Your operating system offers exciting features and easy Internet access. This guide contains information about your operating system and how it functions with your Toshiba computer.
Introduction This guide NOTE The product specifications and configuration information are designed for a product Series. Your particular model may not have all the features and specifications listed or illustrated. For more detailed information about the features and specifications on your particular model, please visit Toshiba's Web site at pcsupport.toshiba.com.
Introduction Safety icons 37 Safety icons This manual contains safety instructions that must be observed in order to avoid potential hazards that could result in personal injuries, damage to your equipment, or loss of data. These safety cautions have been classified according to the seriousness of the risk, and the icons highlight these instructions as follows: Indicates an imminently hazardous situation which, if not avoided, will result in death or serious injury.
Introduction Other documentation Other icons used Additional icons highlight other helpful or educational information: TECHNICAL NOTE: This icon highlights technical information about the computer. HINT: This icon denotes helpful hints and tips. DEFINITION: This icon indicates the definition of a term used in the text. Other documentation Your computer comes with the following documentation: ❖ This electronic user’s guide.
Introduction Service options 39 Service options Toshiba offers a full line of optional service programs to complement its limited warranty. To stay current on the most recent software and hardware options for your computer, and for other product information, be sure to regularly check the Toshiba Web site at pcsupport.toshiba.com. If you have a problem or need to contact Toshiba, see “If Something Goes Wrong” on page 155. 5.375 x 8.375 ver 2.
Chapter 1 Getting Started This chapter provides tips for working comfortably, describes how to connect components, and explains what to do the first time you use your notebook computer. Selecting a place to work Your computer is portable and designed to be used in a variety of circumstances and locations. Creating a computer-friendly environment Place the computer on a flat surface which is large enough for the computer and any other items you need to use, such as a printer.
Getting Started Selecting a place to work 41 ❖ Equipment that generates a strong electromagnetic field, such as stereo speakers (other than speakers that are connected to the computer) or speakerphones. ❖ Rapid changes in temperature or humidity and sources of temperature change such as air conditioner vents or heaters. ❖ Extreme heat, cold, or humidity. ❖ Liquids and corrosive chemicals.
Getting Started Selecting a place to work Placement of the computer Proper placement of the computer and external devices is important to avoid stress-related injuries. ❖ Place the computer on a flat surface at a comfortable height and distance. You should be able to type without twisting your torso or neck, and look at the screen without slouching. ❖ If you are using an external monitor, the top of the display should be no higher than eye level.
Getting Started Selecting a place to work 43 Whichever type you choose, use the following guidelines to adjust your chair for maximum computing comfort. ❖ Position your chair so that the keyboard is at or slightly below the level of your elbow. You should be able to type comfortably with your shoulders relaxed and your forearms parallel to the floor. If you are using a conventional chair: ❖ Your knees should be slightly higher than your hips.
Getting Started Selecting a place to work Your LCD display has a brightness approaching that of a TV device. We recommend that you adjust the brightness of your LCD to a comfortable level to prevent possible strain on your eyes. Arms and wrists ❖ Avoid bending, arching, or twisting your wrists. Keep them in a relaxed, neutral position while typing. ❖ Exercise your hands, wrists, and arms to improve circulation. Using the computer keyboard incorrectly may result in discomfort and possible injury.
Getting Started Selecting a place to work 45 computer frequently and focus your eyes on a distant object for at least 30 seconds. Your LCD display has a brightness approaching that of a TV device. We recommend that you adjust the brightness of your LCD to a comfortable level to prevent possible strain on your eyes. Other precautions Your computer is designed to optimize safety, minimize strain, and withstand the rigors of portability.
Getting Started Selecting a place to work Some PC Cards can become hot with prolonged use. If two cards are installed, both can become hot even if only one is used extensively. Overheating of a PC Card can result in errors or instability in the PC Card operation. Be careful when you remove a PC Card that has been used for lengthy periods of time. ❖ Avoid spilling liquids into the computer’s keyboard. If you do spill a liquid that gets into the keyboard, turn off the computer immediately.
Getting Started Setting up your computer 47 Important information on your computer’s cooling fan Your computer may have a CPU cooling fan that cools the CPU by drawing outside air into the computer. The cooling fan may be located on the bottom of the computer. To prevent possible overheating of the CPU, make sure the air intake on the cooling fan is not blocked. The fan draws in air by creating a vacuum.
Getting Started Setting up your computer Setting up your software The first time you turn on your computer, the Setup Wizard guides you through steps to set up your software. 1 From the welcome screen, click Next to enter the Setup Wizard. 2 Confirm acceptance of Microsoft’s End User License Agreement and click Next. 3 Enter the computer name and description and click Next or Skip.
Getting Started Setting up your computer 49 A window displays the message, “Who will use this computer?” 7 Enter your name and click Next to complete the process. A window displays the message, “Thank you.” 8 Click Finish to continue. Your computer restarts automatically. Registering your computer with Toshiba Product registration is strongly recommended, and allows Toshiba to send Customer periodic updates, announcements, and special offers applicable to the product.
Getting Started Connecting to a power source ❖ Install PC Cards (see “Using PC Cards” on page 147) Connecting to a power source Your computer requires power to operate. Use the power cord/cable and AC adapter to connect the computer to a live electrical outlet, or to charge the computer’s battery. AC adapter Power cord/cable AC adapter cord Sample power cord/cable and AC adapter Hold the power cord/cable by its plug when you connect/ disconnect it. Do NOT pull the cable itself.
Getting Started Connecting to a power source 51 Use only the AC adapter supplied with your computer or an equivalent adapter that is compatible. Use of any incompatible adapter could damage your computer. Toshiba assumes no liability for any damage caused by use of an incompatible adapter. To connect AC power to the computer: 1 Connect the power cord/cable to the AC adapter.
Getting Started Connecting to a power source 2 Plug the AC adapter cord into the DC-IN on the back of the computer. Sample connecting the AC adapter cord to the computer 3 Connect the power cord/cable to a live electrical outlet. The AC power indicator glows when the computer is connected to an external power source. The battery light: ❖ Glows amber while the battery is being charged. ❖ Glows green when the battery is fully charged.
Getting Started Charging the main battery 53 Charging the main battery To charge the main battery, plug the computer into a live wall outlet. It takes several hours to charge the battery with the computer off. It takes much longer to charge the battery while the computer is on. For more information on battery use, see “Running the computer on battery power” on page 111. Once the battery is charged for the first time, avoid leaving the computer plugged in and turned off for more than a few hours at a time.
Getting Started Using the computer for the first time Using the computer for the first time Opening the display panel Slide the display latch to the right and lift the display panel. Sample opening the display panel To avoid damaging the display panel, do not force it beyond the point where it moves easily. Never lift or move the computer using the display panel. Small bright dots may appear on your TFT display when you turn on your computer.
Getting Started Using the computer for the first time 55 Your computer’s features and specifications Certain notebook chassis are designed to accommodate all possible configurations for an entire product Series. Your selected model may not have all the features and specifications corresponding to all of the icons or switches shown on the notebook chassis, unless you have selected all those features.
Getting Started Using the TouchPad™ Using the TouchPad™ The TouchPad, the small, smooth square cutout located in front of the keyboard, is sensitive to touch and enables you to move the cursor with the stroke of a finger. Simply move your finger on the TouchPad in the direction you would like to move the cursor: ❖ To move the cursor to the top of the page, push your finger forward on the TouchPad. ❖ To move the cursor to the bottom of the page, drag your finger toward yourself.
Getting Started Using the TouchPad™ 57 Using the Scroll button For applicable systems, the scroll button, located between the primary and secondary control buttons on the TouchPad, is used for rapid viewing of pages on the screen. Using the Control buttons When a step instructs you to click or choose an item, move the cursor to the item, then press and release the primary (left-hand) button. To double-click, press the primary button twice in rapid succession.
Getting Started Installing additional memory (optional) 8 Close the Printers and Other Hardware window. 9 Close the Control Panel window. NOTE The Fn + F9 shortcut can be used to enable or disable the TouchPad (see “Hot Keys” on page 185). Installing additional memory (optional) Before you install or remove a memory module, turn off the computer using the Start menu. If you install or remove a memory module while the computer is in Stand by or Hibernation mode, data will be lost.
Getting Started Installing additional memory (optional) 59 You need a standard Phillips no. 1 screwdriver to install a memory module. To avoid damaging the computer’s screws, use a standard Phillips no. 1 screwdriver that is in good condition. The computer has two memory module slots—Slot A and Slot B. You can install one or two memory modules. If you are adding memory after you have started to use the computer, begin at step 1, otherwise skip to step 2. 1 Turn off the computer via the Start menu.
Getting Started Installing additional memory (optional) 4 Using a standard Phillips no. 1 screwdriver, unscrew the screw that secures the expansion memory module slot cover, then remove the expansion memory module slot cover. Sample removing the expansion module memory slot cover 5 Put the screw and cover in a safe place so that you can retrieve them later. Static electricity can damage the memory module.
Getting Started Installing additional memory (optional) 8 61 Gently put the memory module connector down at an angle and press down until the clips snap into place. Do not force the memory module into position. The memory module should be level when secured in place. Sample inserting the memory module Avoid touching the connectors on the memory module or on the computer. Grease or dust on the connectors may cause memory access problems. 9 Replace the expansion memory module slot cover.
Getting Started Installing additional memory (optional) Removing a memory module 1 Follow steps 1 through 6 in “Installing additional memory (optional)” on page 58. Do not try to remove a memory module with the computer turned on. You can damage the computer and the device. Do not remove the memory module while the computer is in Standby mode. The computer could hang up the next time you turn it on and data in memory will be lost.
Getting Started Using an external keyboard 63 3 Gently pull the memory module diagonally to pull it out of the slot. 4 Complete the procedure by following steps 10 through 12 in “Installing additional memory (optional)” on page 58. Checking total memory When you add or remove memory, you can check that the computer has recognized the change. To do this: 1 Click Start, then click Control Panel. 2 Click Performance and Maintenance. 3 Click System.
Getting Started Connecting a local printer Connecting a local printer Before you can connect a printer, you need a suitable USB printer cable, which may have been provided with your printer. Otherwise, you can purchase one from a computer or electronics store. Your printer documentation may require you to install the printer software before physically connecting the printer to your computer.
Getting Started Setting up your printer 65 To connect a USB printer: 1 Plug the USB connector into one of the USB ports on your computer 2 Plug the printer’s power cable into a live AC outlet. Connecting a Parallel Printer To connect a parallel printer: Connecting the parallel printer cable while the computer is on may damage the printer, the computer, or both. 1 Connect the printer cable to the printer and to the computer’s parallel port.
Getting Started Setting up your printer Using the Add Printer Wizard To set up a printer with the Add Printer Wizard: 1 Click Start, Control Panel, then Printers and Other Hardware. 2 Select Printers and Faxes. The Printers and Faxes window appears. Sample Printers and Faxes window 3 Click Add Printer. The Add Printer Wizard starts. 5.375 x 8.375 ver 2.
Getting Started Setting up your printer 67 Sample Add Printer Wizard 4 Click Next. The Add Printer Wizard asks you to select your printer. TECHNICAL NOTE: If your printer is Plug and Play, the operating system recognizes it automatically. You can ignore the remainder of this section. See your printer manual. 5 If the printer you are setting up: ❖ Is not connected to a network, select Local printer attached to this computer.
Getting Started Setting up your printer 7 From the list of manufacturers and printers, select your printer, then click Next. 8 Select the port settings according to the instructions in your printer’s documentation and the port to which your printer is connected, then click Next. The Add Printer Wizard prompts you to enter a printer name. 9 Enter a name for your printer. HINT: If you are using more than one printer, make sure the name is descriptive enough to help you tell the difference.
Getting Started Connecting an optional external diskette drive 69 Connecting an optional external diskette drive Some operations, such as creating a password service diskette, require a diskette drive designed for use with 3.5inch diskettes. Sample optional external USB diskette drive To connect an optional external USB diskette drive, connect the cable to one of the USB ports. Sample connecting an optional external USB diskette drive 5.375 x 8.375 ver 2.
Getting Started Connecting external display devices Connecting external display devices Your computer comes with a built-in LCD display, but you can also connect an external display device to the available video port: ❖ An external monitor or projector via the RGB (monitor) port. ❖ A television or video display device via the S-video port. Before connecting an external monitor or video projector, configure your computer for the type of device you are connecting.
Getting Started Connecting external display devices 71 To connect the device: 1 Connect one end of the video cable to the external video device. Refer to the documentation provided with the device for the location of its video-in port. 2 Connect the other end of the video cable to the S-video port on the back of the computer. 3 Turn on the external video device. 4 Set the display mode by pressing Fn + F5, or by setting the Display Properties settings.
Getting Started Connecting external display devices 3 ❖ TV ❖ TV and LCD Release the Fn key. TECHNICAL NOTE: You can also change these settings using the Display Properties Box. Set the option for the video controller by clicking Start, then Control Panel and clicking Display. Choose the Settings tab, click the Advanced button, select Display Device, select the applicable Monitor type, click Apply or OK.
Getting Started Turning off the computer 73 Turning off the computer It is a good idea to turn off your computer when you are not using it for a while. If you are using the computer for the first time, leave the computer plugged into a power source (even though the computer is off) to fully charge the main battery. With the computer off, it may take up to three hours to recharge the main battery.
Getting Started Caring for your computer Closing the display panel When you are finished, shut the computer down and close the display panel to keep dust and dirt out of the computer. If you close the computer while it is still on, these actions will occur: ❖ If you have the LCD power-saver feature set, the LCD panel will automatically turn off until you open it again. ❖ If you have the audible warning set, the computer will beep to notify you that it is still on.
Getting Started Caring for your computer 75 Moving the computer Before moving your computer, even across the room, make sure all disk activity has ended (the disk activity lights stop glowing) and all external peripheral cables are disconnected. Never pick up the computer by its display panel or by the back (where the ports are located). Although your notebook computer is built to withstand reasonable shock and vibration, transport it in a carrying case for long trips.
Getting Started Caring for your computer 3 Insert the cable’s locking end into the security lock slot, then rotate the key a quarter turn and remove it. The computer is now securely locked to deter computer theft. Sample locking the computer 5.375 x 8.375 ver 2.
Chapter 2 Learning the Basics This chapter lists some computing tips and provides important information about basic features. Computing tips ❖ Save your work frequently. Your work temporarily stays in the computer’s memory until you save it to the disk. You will lose all unsaved work, if, for example, a system error occurs and you must restart your computer, or your battery runs out of charge while you are working. Your computer can be configured to warn you when the battery is running low.
Learning the Basics Computing tips ❖ Back up your files to storage media on a regular basis. Label the backup copies clearly and store them in a safe place. If your hard disk suddenly fails, you may lose all the data on it unless you have a separate backup copy. ❖ Use Error-Checking and Disk Defragmenter regularly to conserve disk space and help your computer perform at its optimal level. Consult your Windows® XP operating system documentation for more information on these and other utilities.
Learning the Basics Using the keyboard 79 Using the keyboard Keyboard Character keys Typing with the character keys is very much like typing on a typewriter, except that: ❖ The spacebar creates a space character instead of just passing over an area of the page. ❖ The lowercase l (el) and the number 1 are not interchangeable. ❖ The uppercase letter O and the number 0 are not interchangeable.
Learning the Basics Using the keyboard Ctrl, Fn, and Alt keys Ctrl Alt Fn . Ctrl, Fn and Alt keys The Ctrl, Fn, and Alt keys do different things depending on the program you are using. For more information, see your program documentation. Function keys The function keys (not to be confused with the Fn key) are the 12 keys at the top of the keyboard. Function keys through F12 are called function keys because they run programmed functions when you press them.
Learning the Basics Using the keyboard 81 Overlay keys Keyboard overlay keys The keys with numbers and symbols on the front of them form the numeric and cursor overlay. This overlay lets you enter numeric data or control the cursor as you would using the ten-key keypad on a desktop computer’s keyboard. Using the numeric keypad overlay The keys with the numbers on their right front are the numeric overlay keys. To turn on the numeric keypad overlay, press Fn and F11 simultaneously.
Learning the Basics Using the keyboard To use the cursor control overlay when the numeric overlay is on, press and hold down Shift while you use the cursor control keys. To return to the numeric overlay, release Shift. To turn off the numeric keypad overlay, hold down the Fn key and press F11 again. The numeric mode light on the keyboard indicator panel goes out. Using the cursor control overlay The keys with the gray arrows and symbols on their left front are the cursor control overlay keys.
Learning the Basics Starting a program 83 Starting a program The easiest way to start a program is to double-click the name of the file that contains the information you want to work on. To find the file, use My Computer or Windows Explorer.
Learning the Basics Starting a program Starting a program from Windows® Explorer If a program is not listed in the Programs menu, you can start it from Windows® Explorer. Windows® Explorer gives you a view of your computer’s contents as a hierarchy or “tree.” You can easily see the content of each drive and folder on your computer. To use this method, you should know the file name and location of the program’s executable file (this file ends with .exe).
Learning the Basics Starting a program 85 Starting a program from the Run dialog box This example uses the Run command to start WordPad: 1 Click Start, then click Run. The Run dialog box appears. Sample Run dialog box 2 In the Run dialog box: ❖ If you know the program’s location, type the command line. For a program in the Windows® folder, type just the program name. Otherwise, type the full file path. For example, to access WordPad, type: c:\Program Files\WindowsNT\Accessories\Wordpad, then click OK.
Learning the Basics Saving your work Saving your work Before you turn off the computer, save your work to the hard disk drive. Always save your data even when you are using the Stand by. If your battery fully discharges, your information will be lost. Your computer can be configured to warn you when the battery is running low, see “Power management” on page 112. Saving files 1 On the File menu of your Windows® program, click Save.
Learning the Basics Saving your work 3 87 Type a file name, then click Save. HINT: To make another copy of the file you are currently working with, choose Save As from the File menu and give the new file a different name. The Windows® XP operating system supports file names of up to 255 characters; the names can include spaces. Some applications still require MS-DOS® file names.
Learning the Basics Printing your work To save: ❖ A file you are updating, open the program’s File menu and click Save. ❖ A new file, choose Save As from the File menu, type a name for the file, and click OK. HINT: To make another copy of the file you are currently working with, choose Save As from the File menu and give the new file a different name. Printing your work Verify that the Windows® XP operating system is set up for your printer as described in “Setting up your printer” on page 65.
Learning the Basics Backing up your files 89 Backing up your files Backing up your files means copying individual files to media, such as CDs, or copying entire sections of your hard disk to another device, such as a tape drive. For those systems with a writable CD-ROM drive or DVDROM multi-function drive, you may back up file to a writable disc as follows: 1 To back up to a CD or other media, insert the media into the appropriate drive. 2 Click Start, then click My Computer.
Learning the Basics Using the DVD-ROM or multi-function drive Using the DVD-ROM or multi-function drive Optical storage has become the preferred medium for software, music, and video. Digital versatile discs (DVDs) provide a significant increase in data storage and support features that are not available on any other video platform. These features include wide-screen movies, multiple language tracks, digital surround sound, multiple camera angles, and interactive menus.
Learning the Basics Using the DVD-ROM or multi-function drive 91 DVD-ROM or multi-function drive components Your DVD-ROM or multi-function drive may look like this: Eject button Manual eject hole Sample DVD-ROM or multi-function drive Never press the eject button or turn off the computer while the drive-in-use indicator light is glowing. Doing so could damage the disc or the drive. The eject button requires power to operate. The manual eject button does not require power.
Learning the Basics Using the DVD-ROM or multi-function drive CD/DVD control and Music CD buttons The control buttons to the left of the keyboard let you to play audio CDs when the computer is off. You can also use them to play CDs and DVDs when the computer is on.
Learning the Basics Using the DVD-ROM or multi-function drive 93 The next track button skips to the following track on the disc. The previous track button returns to the preceding track on the disc. Inserting a disc Before playing an audio CD, turn the volume down. Playing the compact disc at maximum volume could damage your ears. To turn the volume down, use the Volume Control switch or access the Volume Control program (click Start, All Programs, Accessories, Entertainment, Volume Control).
Learning the Basics Using the DVD-ROM or multi-function drive Sample inserting a disc Be careful not to touch the drive’s lens (located underneath the drive’s spindle) or the area around it. Doing so could cause the drive to malfunction. 5 Gently press the center of the disc onto the spindle until it locks into place. Spindle Correct position Disc Incorrect position Incorrect position Sample positioning the disc on the spindle Make sure the disc is properly positioned on the spindle.
Learning the Basics Using the DVD-ROM or multi-function drive 6 95 Close the disc tray by pressing gently on the center of the tray until it clicks indicating that it is locked. Playing an audio CD Insert an audio CD and close the disc tray. The computer automatically detects a disc in the drive and opens the Audio CD window. To play an audio CD select the Play Audio CD using Windows Media® Player option and click OK. Sample Audio CD window The Windows Media Player window appears. 5.375 x 8.375 ver 2.
Learning the Basics Using the DVD-ROM or multi-function drive Rewind Play Fast forward Stop Volume control Previous track Next track Mute Sample Windows Media® Player screen The Windows Media Player control panel works much like an ordinary compact disc player: ❖ To play the CD or to pause, click the Play/Pause button on the CD Player control panel. ❖ To stop the CD, click the Stop button. 5.375 x 8.375 ver 2.
Learning the Basics Using the DVD-ROM or multi-function drive 97 Playing CDs using Auto-Run If you insert a CD into the DVD-ROM/multi-function drive and the Auto-Run feature does not automatically start your disk, try launching the CD manually. To do this, follow these steps: 1 Open the Start menu and select My Computer. 2 Click the DVD-ROM/multi-function drive icon. The disk drive will run the CD.
Learning the Basics Using the DVD-ROM or multi-function drive Viewing the contents of a CD or DVD CDs and DVDs contain files just like the hard disk. CDs are often used to install software or store files that require lots of space, such as photographs and large presentation files. You can use Explorer or My Computer to view the contents of any CD or DVD. Removing a disc with the computer on Never press the eject button or turn off the computer while the drive-in-use light is glowing.
Learning the Basics Using the DVD-ROM or multi-function drive 99 Removing a disc with the computer off 1 Insert a slender object, such as a straightened paper clip, into the manual eject button access hole. Never use a pencil to press the manual eject button. Pencil lead can break off inside the computer and damage it. 2 Pull the tray fully open, remove the disc and place it in its protective cover.
Learning the Basics Powering down the computer Powering down the computer ® Pushing the power button before shutting down the Windows operating system could cause you to lose your work. Make sure the system indicator panel’s disk light and the drive-inuse light are off. If you turn off the power while a disk is being accessed, you may lose data or damage the disk and/or drive. When you power down the computer, you have three options to choose from: Turn Off, Stand By, and Hibernation.
Learning the Basics Powering down the computer 101 Sample Turn off computer dialog box 2 Click Turn Off. The computer shuts down completely. For the Windows® XP Professional operating system, follow these steps to shut down the computer: 1 Click the Start button, then Shut down. The Shut Down Windows dialog box appears. 2 Select Shut down from the drop-down list. 3 Click OK. The computer shuts down completely.
Learning the Basics Powering down the computer 1 Click Start, Control Panel, then Performance and Maintenance. 2 Click the Toshiba Power Management icon. The Power Options Properties dialog box appears. 3 Click the Advanced tab, and select the options you want. ❖ When I close the lid of my portable computer Set this option to Power Off to have the computer shut down when you close the display panel.
Learning the Basics Powering down the computer 103 Using Hibernation Mode The Hibernation command shuts the computer down completely, but it first saves the current state of the computer to the hard disk. Since Hibernation mode does not require power to maintain the saved information, the system settings are retained indefinitely. Restoring information from the hard disk takes longer than restoring it from memory.
Learning the Basics Powering down the computer Configuring your computer for Hibernation 1 Open the Start menu, click Control Panel, then Performance and Maintenance. 2 Click the Toshiba Power Management icon. 3 Click the Setup Action tab. 4 Select Hibernation for the options you want. ❖ When I press the power button Set this option to Hibernate so that the computer will go into Hibernation mode when you press the power button.
Learning the Basics Powering down the computer 105 Sample Turn off computer dialog box 3 Click Hibernate. The computer saves the mode of the system, including all open programs and files, to the hard disk, and then powers down completely. Going into Hibernation mode more quickly You can also put the computer into Hibernation mode by pressing the power button or closing the display panel. 1 Click Start, Control Panel, then Performance and Maintenance. 2 Click the Toshiba Power Management icon.
Learning the Basics Powering down the computer Sample Toshiba Power Management Advanced tab 4 Click Apply. 5 Click OK, then close the Control Panel. Starting again from Hibernation mode To start the computer from Hibernation mode, press and release the power button. The computer returns to the screen you were using. If you put the computer in Hibernation mode by closing the display panel, you can start it again by opening the display panel.
Learning the Basics Powering down the computer 107 Using Standby Mode Standby mode places the computer into a power-saving mode. Standby holds the current state of the computer in memory so that, when you restart the computer, you can continue working from where you left off. Factors to consider when choosing Standby: ❖ While in Standby mode, the computer uses some battery power. The battery will eventually discharge in Stand by mode.
NOTE Learning the Basics Powering down the computer If you hold down the Shift key, Stand By becomes Hibernate in the Turn off computer dialog box. To enter hibernation mode, you must hold down the Shift key while you select Hibernate. The computer saves the status of all open programs and files, turns off the display, and enters into a low-power mode. The on/off light blinks amber, indicating the machine is in Standby mode.
Learning the Basics Powering down the computer 109 If you power down using the Stand by and the battery discharges fully, your information will be lost. Be sure to save your work first. Going into Standby mode more quickly You can also configure the computer to enter into Standby mode by either pressing the power button or closing the display panel. You can also specify an amount of time after which the computer automatically enters into Standby mode.
Learning the Basics Toshiba’s online resources Starting again from Standby mode To restart the computer from Standby mode, press the power button until the on/off light changes to green. The computer returns to the screen you were previously using. If you place the computer in Standby mode by closing the display panel, you can start it again by opening the display panel. Toshiba’s online resources Toshiba maintains a number of online sites to which you can connect.
Chapter 3 Mobile Computing This chapter covers all aspects of using your computer while traveling. Toshiba’s energy-saver design Your computer enters a low-power standby mode when it is not being used, thereby conserving energy and saving money in the process. It has a number of other features that enhance its energy efficiency. Many of these energy-saving features have been set by Toshiba.
Mobile Computing Running the computer on battery power Battery Notice Battery life may vary depending on applications, power management settings and features utilized. Recharge time varies depending on usage. The battery may not charge while the computer is consuming full power. After a period of time, the battery will lose its ability to perform at maximum capacity and will need to be replaced. This is normal for all batteries.
Mobile Computing Charging the batteries 113 Changes to these settings may result in system performance or stability issues. Users who are not completely familiar with the power management component of the system should use the preset configuration. For assistance with setup changes, contact Toshiba’s Global Support Centre. Using additional batteries If you spend a lot of time traveling and need to work for many hours without an AC power source, you may want to carry additional charged batteries with you.
Mobile Computing Charging the batteries Never leave batteries in the battery charger for more than a week at a time. Doing so may reduce the potential charge of the battery. Use only battery chargers designed to work with your notebook computer. You can order a Toshiba battery charger from Toshiba’s Web site at accessories.toshiba.com. Charging the main battery To charge the battery, plug the computer into a live wall outlet. It takes several hours to charge the battery with the computer off.
Mobile Computing Charging the batteries 115 Leave the power connected, and the battery should begin charging after a few minutes. HINT: Once the battery is fully charged, we recommend that you operate your computer on battery power until the battery discharges completely. Doing this extends battery life and helps ensure accurate monitoring of battery capacity. Charging the RTC battery Your computer has an internal real-time clock (RTC) battery.
NOTE Mobile Computing Monitoring battery power It is seldom necessary to charge the RTC battery because it charges while the computer is on. If the RTC battery is low, the real-time clock and calendar may display the incorrect time and date or stop working. When Hibernation mode is enabled and the RTC battery is completely discharged, a warning prompts you to reset the real-time clock.
Mobile Computing Monitoring battery power 117 Determining remaining battery power NOTE Wait at least 16 seconds after turning on the computer before trying to monitor the remaining battery power. The computer needs this time to check the battery’s remaining capacity and perform its calculations. 1 Click Start, Control Panel, then Performance and Maintenance. 2 Click the Toshiba Power Management icon.
Mobile Computing Monitoring battery power TECHNICAL NOTE: The computer drains the battery faster at low temperatures. Check your remaining charge frequently if you are working in temperatures below 50 degrees Fahrenheit. The computer calculates the remaining battery charge based on your current rate of power use and other factors such as the age of the battery.
Mobile Computing Monitoring battery power 119 an alarm, display a message, both, or none. You can also set the computer to enter Standby mode or Hibernate mode or to completely power down when the alarm goes off. To set an alarm: 1 Click Start, Control Panel, then Performance and Maintenance. 2 Click the Toshiba Power Management icon. 3 Click the Alarm tab and set the alarm, as desired.
Mobile Computing Monitoring battery power ❖ Whether you use any optional devices to which the battery supplies power, such as a PC Card ❖ Where you are working—since operating time decreases at low temperatures There are various ways in which you can conserve power and extend the operating time of your battery: ❖ Enable Standby or Hibernation, which saves power when you turn off the computer and turn it back on again. ❖ Use Toshiba’s power-saving options.
Mobile Computing Monitoring battery power 121 Using a hot key to set the power profile You may use a hot key to set the power profile. To set the power profile: 1 Press Fn and F2 simultaneously to display the power profile pop-up window. Sample Power Profile mode pop-up window 2 While continuing to press Fn, press F2 until you select the desired power profile. The power profile options are: Full Power, High Power, Normal, DVD Playback, Presentation, and Long Life. 3 Release the Fn key.
Mobile Computing Changing the main battery Changing the main battery When your battery power is running low, you have two options—connect the computer to an AC power source or install a charged battery. When handling a battery, be careful not to drop it or shortcircuit its terminals. Also, do not drop, hit or otherwise impact the battery. Do not scratch or break the casing and do not twist or bend the battery pack. Do not remove the battery pack while the computer is in Standby mode.
Mobile Computing Changing the main battery 123 Sample unlocking the battery 6 Push and hold the battery release latch. Sample releasing the battery 7 While still holding the release latch in the open position gently lift the battery pack out of the computer. 5.375 x 8.375 ver 2.
Mobile Computing Changing the main battery Sample removing the battery If the battery is leaking or its case is cracked, put on protective gloves to handle it, and discard it immediately following the advice in “Disposing of used batteries safely” on page 127. Inserting the battery into the computer Assuming you just removed the battery pack (see “Removing the battery from the computer” on page 122): 1 Place the battery pack in the battery compartment.
Mobile Computing Taking care of your battery 125 The battery pack has been designed so that you cannot install it with reverse polarity. Sample inserting battery NOTE When you replace your battery, slide the battery lock towards you to lock the battery pack. Taking care of your battery The following sections offer tips on how to take care of your battery and prolong its life.
Mobile Computing Taking care of your battery ❖ Avoid touching the metal terminals of the battery with another metal object. Short-circuiting the battery can cause it to overheat and may cause damage to the battery or the computer. ❖ Do not incinerate a spent battery, as this could cause it to explode and release toxic materials. ❖ If a battery is leaking or damaged, replace it immediately. Use protective gloves when handling a damaged battery.
Mobile Computing Disposing of used batteries safely 127 4 Connect the AC adapter to the computer and the power cord to a power outlet. The DC-IN or AC power-light should glow green, and the battery should glow amber to indicate that the battery pack is being charged. If the DCIN or AC power-light indicator does not glow, power is not being supplied. Check the connections for the AC adapter and power cord. 5 Charge the battery pack until the battery glows green.
Mobile Computing Traveling tips After repeated use, the batteries will finally lose their ability to hold a charge and you will need to replace them. Under federal, state and local laws, it may be illegal to dispose of old batteries by placing them in the trash. Please be kind to our shared environment. Check with your local government authority for details regarding where to recycle old batteries or how to dispose of them properly.
Chapter 4 Exploring Your Options In this chapter, you will explore other features of your notebook computer. In this chapter, you will explore some of the special features of your Satellite® Series notebook computer. Exploring the desktop The desktop is the launching pad for everything you can do in the Windows® XP Home or XP Professional operating system. You use its features to start programs, find documents, set up system components, and perform most other computing tasks.
Exploring Your Options Exploring the desktop Finding your way around the desktop Your computer’s desktop includes several standard features: icons, Start button, taskbar, system tray, and background pattern. Icons Taskbar Start button System tray ® Sample Windows XP operating system desktop Icons An icon represents a folder, file, or program that can be quickly activated by double-clicking the icon.
Exploring Your Options Exploring the desktop 131 Recycle Bin — Holds files you have deleted. You may be able to retrieve these files until you empty the Recycle Bin. TECHNICAL NOTE: If you delete a file from a diskette, it does not go into the Recycle Bin. For more information on the Recycle Bin, see Windows online Help. Internet Explorer — The Microsoft® browser that provides access to the Internet. NOTE If you place the cursor over an icon, a popup description of the file contents appears.
Exploring Your Options Exploring the desktop Taskbar Each time you open a program, a button associated with that program appears on the taskbar. With some programs, a button appears on the taskbar for each document or window you open. You can use these buttons to quickly switch between the programs or windows. To make a program or window the currently active one, click the associated taskbar button.
Exploring Your Options Setting up for communications 133 Setting up for communications Your computer comes with a built-in modem that can be connected to a standard voice-grade telephone line. The modem allows you to: ❖ Access the Internet. ❖ Communicate with your office’s local area network (LAN), or a larger corporate wide area network (WAN). For specific information about connecting to a LAN or WAN, consult your network administrator. ❖ Send a fax directly from your computer.
Exploring Your Options Setting up for communications Determining the COM port Your modem is connected to one of the computer’s COM (communications) ports. The default setting for the modem is COM3. The following procedure is intended to support you if you need to either upgrade your modem or reset the port to the default settings. If you are having trouble connecting through the modem, you may need to determine the current COM port name and possibly change it.
Exploring Your Options Setting up for communications 135 Connecting the modem to a telephone line Before you can communicate using the modem, you need to connect it to a telephone line. Your computer’s built-in modem port provides an RJ-11 jack, allowing you to connect the modem to a standard voice-grade telephone line. 1 Plug one end of a telephone cable (purchased separately) into the modem port on the back of the computer.
Exploring Your Options Setting up for communications Now you are ready to send a fax or use the modem to connect to an online service or the Internet. Connecting your computer to a network You can connect your computer to a network to increase its capabilities and functionality using one of its communication ports. Accessing a network To access a network: ❖ At the office, connect an Ethernet cable to the RJ-45 jack on your computer.
Exploring Your Options Setting up for communications 137 Using the Ethernet LAN Port When your computer starts, Windows attempts to contact a Dynamic Host Configuration Protocol (DHCP) server. If the computer is not connected to a network, it may pause a few minutes as it waits for a reply. To avoid this delay, you can reconfigure Windows to disable the LAN port. TECHNICAL NOTE: You can also use ConfigFree to reconfigure Windows to disable the LAN port.
Exploring Your Options Setting up for communications Using Wireless LAN Connectivity NOTE The transmission speed over the wireless LAN and the distance over which wireless LAN can reach may vary depending on surrounding electromagnetic environment, obstacles, access point design and configuration, and client design and software/hardware configurations. Your system may come with an optional wireless LAN module.
Exploring Your Options An overview of using the Internet 139 An overview of using the Internet The following sections give a quick introduction to the Internet and some of its exciting features, under these headings: ❖ The Internet ❖ The World Wide Web ❖ Internet Service Providers ❖ Connecting to the Internet ❖ Surfing the Internet ❖ Internet features ❖ Uploading and downloading files from the Internet The Internet The Internet is an association of thousands of networks and millions of compu
Exploring Your Options An overview of using the Internet Internet Service Providers To connect a computer directly to the Internet, many people and businesses use an Internet Service Provider (ISP). An ISP is a company that has the equipment and the telecommunication lines necessary to maintain an Internet connection. You can connect to the Internet by using a telephone and modem or through other higher-speed communication methods such as Digital Subscriber Lines (DSL), cable, and satellite links.
Exploring Your Options An overview of using the Internet 141 Surfing the Internet Once connected to the Internet, the Web browser displays a home page, for example, your ISP’s home page on the Internet or your company’s Web site home page. To visit a desired Web site, type the Web address. The Web address, or Uniform Resource Locator (URL), is a unique identifier for that computer system linked to the Internet. Web addresses can also appear within a Web page’s text, and are known as links.
❖ Exploring Your Options Exploring video features Online shopping Many Web sites offer products and services for sale. Uploading and downloading files from the Internet Transferring files from one computer to another is termed uploading (transferring data from your computer to a site on the Web), or downloading (transferring data from a site on the Web to your computer). There are several ways to upload or download data.
Exploring Your Options Changing the display properties setting 143 Changing the display properties setting 1 Right-click anywhere on your desktop and select Properties. The Display Properties dialog box appears. Sample Display Properties dialog box 2 Click the Settings tab. 3 Slide the Screen area slider bar toward Less until the setting reads 800 x 600, then click Apply. The screen blinks momentarily while the settings are adjusted.
Exploring Your Options Exploring audio features Exploring audio features You can use your computer to record sounds using an external microphone. You can play .wav sound files or audio CDs using the built-in speakers, headphones or external speakers. Recording sounds You can make audio recordings and save them as .wav files by connecting an external microphone or other sound source to the microphone jack and using the Sound Recorder feature in the operating system. DEFINITION: A .
Exploring Your Options Exploring audio features 145 Positioning bar Record Stop Play Skip forward Skip backward Sample Sound Recorder screen 3 NOTE Click the Record button and speak normally into the microphone. You can only record 60 seconds at a time. 4 When you have finished recording, click the Stop button. 5 To hear what you just recorded, click the Play button. 6 To save the file, select Save from the File menu.
4 Exploring Your Options Using the i.LINK® port Click OK. Your new settings take effect the next time you record. Using external speakers or headphones Your computer is equipped with a full stereo sound system with internal speakers. Instead of using the internal speakers, you can connect headphones or a pair of external stereo speakers. Before playing an audio CD, turn the volume down. Playing the compact disc at maximum volume could damage your ears.
Exploring Your Options Using PC Cards 147 Using PC Cards PC Cards expand your computer’s capabilities and usefulness. You can purchase additional PC Cards from your dealer. Most PC Cards conform to the PCMCIA (Personal Computer Memory Card International Association) standard. Your computer has one PC Card slot and supports Type II PC Cards. Check the documentation that came with the PC Card to see if it conforms to the PCMCIA 2.1 standard, or later.
Exploring Your Options Using PC Cards You may also hot swap a PC Card. Stop the PC Card by clicking the Safely Remove Hardware icon on the System tray. After the Safe to Remove Hardware message appears, it is safe to remove the PC Card. 2 Align the card connectors with an available PC Card slot and carefully slide the card into the slot until it locks into place. Sample inserting a PC Card To avoid damaging the PC Card or the computer, do not force the card into the PC Card slot.
Exploring Your Options Using PC Cards 149 Sample removing a PC Card Hot swapping One of the great things about PC Cards is that you can replace one PC Card with another while the computer is on. This is called “hot swapping.” Hot swapping precautions Although you can insert a PC Card at any time, to avoid data loss never remove a card while it is in use. For example: ❖ Never remove a hard disk card while the system is accessing it. ❖ Never remove a network card while you are connected to a network.
Exploring Your Options Using the Bridge Media slot Using the Bridge Media slot Your computer is equipped with a Bridge Media Slot, which supports the use of Memory Stick or Memory Stick PRO media, Secure DigitalTM (SDTM) Cards, SmartMedia™, or xD-Picture Cards. This media can be used with a variety of digital products: digital music players, cellular phones, PDAs, digital cameras, digital video camcorders, etc. NOTE Do not use the Copy Disk function for this type of media.
Exploring Your Options Using the Bridge Media slot 151 Removing Memory Stick or Memory Stick PRO media 1 Right-click the Safely Remove Hardware icon on the System tray. After the media is stopped, it is safe to remove. 2 Grasp the card and pull it straight out. Inserting an SD™ Card 1 Turn the card so that the contacts (metal areas) are face down. 2 Push the card into the slot until it locks in place. Sample inserting an SD Card Do not touch the SD™ connector (metal area).
Exploring Your Options Using the Bridge Media slot Removing an SD™ Card 1 Right-click the Safely Remove Hardware icon on the System tray. After the card is stopped, it is safe to remove. 2 Grasp the card and pull it straight out. Inserting an xD-Picture Card™ 1 Turn the card so that the contacts (metal areas) are face down. 2 Push the card into the slot until it locks in place. Sample inserting an xD-Picture Card Do not touch the xD-Picture™ Card connector (metal area).
Exploring Your Options Using the Bridge Media slot 153 Removing an xD-Picture Card™ 1 Right-click the Safely Remove Hardware icon on the System tray. After the card is stopped, it is safe to remove. 2 Grasp the card and pull it straight out. Inserting a SmartMedia Card™ 1 Turn the card so that the contacts (metal areas) are face down. 2 Push the card into the slot until it locks in place. Sample inserting an Smart Media Card Do not touch the Smart Media™ Card connector (metal area).
Exploring Your Options Using the Bridge Media slot Removing a SmartMedia Card™ 1 Right-click the Safely Remove Hardware icon on the System tray. After the card is stopped, it is safe to remove. 2 Grasp the card and pull it straight out. 5.375 x 8.375 ver 2.
Chapter 5 If Something Goes Wrong Some problems you may encounter when using your notebook computer are relatively easy to identify and solve. Others may require help from your dealer or the manufacturer of a software program. This chapter aims to help you solve many problems by yourself. It covers the problems you are most likely to encounter. If all else fails, contact Toshiba. You will find information on Toshiba’s support services at the end of this chapter.
If Something Goes Wrong Problems that are easy to fix 2 The Windows Task Manager appears. 3 Click the Applications tab. If a program has stopped responding, the words “not responding” appear beside its name in the list. Sample Windows Task Manager Applications tab 4 Select the program you want to close, then click End Task. Closing the failed program should allow you to continue working. If it does not, continue with step 3.
If Something Goes Wrong Problems that are easy to fix 157 Sample Windows Task Manager Shutdown menu, Turn Off option The computer shuts down. Your program performs an illegal operation. If you receive the message, “Your program has performed an illegal operation,” you should record the details of the message and consult the software manufacturer. To record the details: 1 Click the Details button and select the text the operating system displays.
If Something Goes Wrong Problems when you turn on the computer 6 Save the file and refer to it when you contact the software manufacturer. Problems when you turn on the computer These problems may occur when you turn on the power. The computer will not start. Make sure you attached the AC adapter and power cord/cable properly or installed a charged battery. Press and hold down the power button for a few seconds.
If Something Goes Wrong The Windows operating system is not working ® 159 The Windows® operating system is not working Once you are familiar with the desktop and used to the way the operating system responds to your work routine, you can easily detect if the operating system is not working correctly. For example: ❖ The operating system fails to start after the Starting Windows XP message appears. ❖ The operating system takes a long time to start.
If Something Goes Wrong The Windows® operating system is not working ❖ Safe Mode (with Command Prompt) ❖ Enable Boot Logging ❖ Enable VGA Mode ❖ Last known good configuration (your most recent settings that worked) ❖ Directory services restore mode (Windows® domain controllers only) ❖ Debugging Mode ❖ Disable Automatic Restart on System Failure ❖ Start Windows® normally ❖ Reboot ❖ Return to OS Choices Menu For detailed information, refer to your operating system’s documentation.
If Something Goes Wrong Resolving a hardware conflict 161 and the syntax of the address carefully. A single incorrect letter or missed character, comma instead of period (“dot”) or other mistake makes it impossible for your browser to locate the site. My browser cannot find a site I bookmarked. The World Wide Web is constantly changing. A site you bookmarked yesterday may not be available today or its server may be down for temporary repair. Try again later.
If Something Goes Wrong Resolving a hardware conflict A list of category links appear. 3 Click the Fixing a hardware problem or other appropriate link. 4 Choose from specific topics and follow the steps. If there is still a problem, the operating system should display a message that explains what the conflict is. A plan of action The smooth operation of the system depends on the interaction of all devices, programs, and features.
If Something Goes Wrong Resolving a hardware conflict 163 Direct Memory Access Similarly, the data required by the device is stored in a specific place or address in memory called the Direct Memory Access (DMA). The DMA provides a dedicated channel for adapter cards to bypass the microprocessor and access memory directly. If two or more devices use the same DMA, the data required by one device overwrites the data required by the other. That may cause a hardware conflict.
If Something Goes Wrong Resolving a hardware conflict ❖ Reconfigure the device so that its requirements do not conflict. Refer to the device’s documentation for instructions about changing settings on the device. Fixing a problem with Device Manager Device Manager provides a way to check and change the configuration of a device. Changing the default settings using Device Manager can cause other conflicts that make one or more devices unusable.
If Something Goes Wrong Resolving a hardware conflict 165 Checking device properties Device Manager provides a way to view the properties of a device. Properties include the name of the manufacturer, the type of device, the drivers installed, and the system resources assigned to the device. To check a device’s properties: 1 Click Start. 2 Click My Computer with the secondary button, then click Properties. The System Properties dialog box appears. 3 Click the Hardware tab.
If Something Goes Wrong Resolving a hardware conflict Memory problems Incorrectly connected or faulty memory modules may cause errors that seem to be device-related. It is worthwhile checking for these first: 1 Turn off the computer via the Start menu. 2 Remove the memory module. 3 Reinstall the memory module, following the instructions in “Using the computer for the first time” on page 54, and making sure it is seated properly. 4 Check for the error again.
If Something Goes Wrong Resolving a hardware conflict 167 Here are some typical problems and how to solve them: The AC power light does not come on when you plug in the AC adapter and power cord/cable. Make sure the AC adapter and power cord/cable are firmly plugged into both the wall outlet and the computer. If the AC power light still does not come on, check that the wall outlet is working properly by plugging in a lamp or other appliance.
If Something Goes Wrong Resolving a hardware conflict Check the power options using the Toshiba Power Management Utility. Have you added a device, such as a PC Card or memory module, that takes its power from the battery? Is your software using the hard disk more? Is the display power set to turn off automatically? Was the battery fully charged to begin with? All these conditions affect how long the charge lasts.
If Something Goes Wrong Resolving a hardware conflict 169 Display problems Here are some typical display problems and their solutions: The display is blank. Display Auto Off may have gone into effect. Press any key to activate the screen. You may have activated the instant password feature by pressing Fn and F1 simultaneously. If you have registered a password, press the Enter key, type the password and press Enter. If no password is registered, press Enter.
If Something Goes Wrong Resolving a hardware conflict The built-in screen flickers. Some flickering is a normal result of the way the screen produces colors. To reduce the amount of flickering, try using fewer colors. To change the number of colors displayed: 1 Point at the desktop and click with the secondary button. 2 Click Properties, and then the Settings tab. 3 Choose a lower quality color option and click OK. For more information, see Windows ® Help.
If Something Goes Wrong Resolving a hardware conflict 171 Small bright dots appear on your TFT display when you turn on your computer. Your display contains an extremely large number of thin-film transistors (TFT) and is manufactured using high-precision technology. The small bright dots that appear on your display are an intrinsic characteristic of the TFT manufacturing technology. NOTE Over a period of time, and depending on the usage of the computer, the brightness of the LCD Screen will deteriorate.
If Something Goes Wrong Resolving a hardware conflict The drive’s properties box appears. 3 Click on Properties. 4 Click the Tools tab. 5 Click the Check now button. The Check Disk box appears (for example, Check Disk C). 6 You can choose one or both options: ❖ Automatically fix file system errors ❖ Scan for and attempt recovery of bad sectors ❖ Click Start. Error-checking runs the test. Your hard disk seems very slow.
If Something Goes Wrong Resolving a hardware conflict 173 DVD-ROM or multi-function drive problems You cannot access a disc in the drive. Make sure the drive tray has closed properly. Press gently until it clicks into place. Open the drive tray and remove the disc. Make sure the drive tray is clean. Any dirt or foreign object can interfere with the laser beam. Examine the disc to see whether it is dirty. If necessary, wipe it with a clean cloth dipped in water or a neutral cleaner.
If Something Goes Wrong Resolving a hardware conflict The color of the materials used to make the disc can affect its reliability. Silver-colored CD-ROMs are the most reliable, followed by gold-colored CD-ROM. Green-colored CDROMs are the least reliable. Sound system problems You do not hear any sound from the computer. Adjust the volume control. If you are using external headphones or speakers, check that they are securely connected to your computer. The computer emits a loud, high-pitched noise.
If Something Goes Wrong Resolving a hardware conflict 175 Card Information Structure When you insert a PC Card into a slot, the computer attempts to determine the type of card and the resources it requires by reading its Card Information Structure (CIS). Sometimes the CIS contains enough information for you to use the card immediately. Other cards must be set up before you can use them. Use the Windows ® XP PC Card (PCMCIA) Wizard to set up the card.
If Something Goes Wrong Resolving a hardware conflict Resolving PC Card problems Here are some common problems and their solutions: The slots appear to be dead. PC Cards that used to work no longer work. Check the PC Card status: 1 Click Start. 2 Click My Computer icon with the secondary button, then click Properties. The System Properties dialog box appears. 3 Click the Hardware tab. 4 Click the Device Manager button. 5 Double-click the category listed as PCMCIA adapter.
If Something Goes Wrong Resolving a hardware conflict 2 177 Click Stop xxxx, where xxxx is the identifier for your PC Card. The operating system displays a message that you may safely remove the card. 3 Remove the card from the slot. Never swap modules when the computer is in Hibernation or Standby mode.
If Something Goes Wrong Resolving a hardware conflict Printer problems This section lists some of the most common printer problems: The printer will not print. Check that the printer is connected to a working power outlet, turned on and ready (on line). Check that the printer has plenty of paper. Some printers will not start printing when there are just two or three sheets of paper left in the tray. Make sure the USB printer cable is firmly attached to the computer and the printer.
If Something Goes Wrong Develop good computing habits 179 Modem problems This section lists common modem problems: The modem will not receive or transmit properly. Make sure the cable from the modem to the telephone line is firmly connected to the computer’s modem port and the telephone line jack. Check the port settings to make sure the hardware and software are referring to the same COM port. See “Determining the COM port” on page 134.
If Something Goes Wrong Develop good computing habits On a regular basis, back up the information stored on your hard disk. Here are some ways you can do this: ❖ Copy files to a CD or other media, following the steps in “Saving your work” on page 86. ❖ Connect a tape drive to the system and use specialized software to copy everything on the hard disk to a tape.
If Something Goes Wrong If you need further assistance 181 If you need further assistance If you have followed the recommendations in this chapter and are still having problems, you may need additional technical assistance. This section contains the steps to take to ask for help. Before you call Since some problems may be related to the operating system or the program you are using, it is important to investigate other sources of assistance first.
If Something Goes Wrong If you need further assistance Contacting Toshiba If you still need help and suspect that the problem is hardware-related, Toshiba offers a variety of resources to help you. You can access Toshiba on the Internet using any Internet browser by typing support.toshiba.com Toshiba voice contact Before calling Toshiba, make sure you have: ❖ Your computer’s serial number. ❖ The computer and any optional devices related to the problem.
If Something Goes Wrong Other Toshiba Internet Web sites 183 Other Toshiba Internet Web sites toshiba.com Worldwide Toshiba corporate site computers.toshiba.com Marketing and product information in the USA www.toshiba.ca Canada www.toshiba-Europe.com Europe www.toshiba.co.jp/index.htm Japan http://servicio.toshiba.com Mexico and all of Latin America Toshiba’s worldwide offices Australia Toshiba (Australia) Pty.
If Something Goes Wrong Toshiba’s worldwide offices Latin America and Caribbean Toshiba America Information Systems 9740 Irvine Blvd. Irvine, California 92618 USA Mexico Toshiba de México S.A. de C.V. Sierra Candela No.111, 6to. Piso Col. Lomas de Chapultepec. CP 11000 Mexico, DF. 800-457-7777 (within the US) 949-859-4273 (outside of the US this call may incur long-distance charges) Spain Toshiba Information Systems (España) S.A.
Appendix A Hot Keys Hot keys are keys that, when pressed in combination with the Fn key, turn system functions on and off. Hot keys have a legend on or above the key indicating the option or feature the key controls. Volume Mute Fn + This hot key enables/disables volume mute on your computer. When volume mute is enabled, no sound will come from the speakers or headphones. 185 5.375 x 8.375 ver 2.
Hot Keys Instant password security Instant password security F1 Fn + This hot key blanks the display. Without a password The Fn + F1 key combination turns off the display and activates instant security. Using the pointing device or any key will make the display’s content reappear, if no password is set for the current user. With a password The Fn + F1 key combination turns off the display and activates instant security.
Hot Keys Instant password security 187 Maintaining security when the battery is not fully charged When the battery is not fully charged (even if the computer is operating on AC power) your display may reappear automatically after a short time. To protect your desktop, you must set up a screen saver with a password before activating the password feature. To set up a password with a screen saver, go to Windows XP Help for instructions: 1 Click Start, Help and Support.
Hot Keys Power usage mode Power usage mode Fn + This hot key displays the power usage pop-up window and cycles through the battery save modes. The power usage modes in the operating system under battery power are: Long Life, Normal, and High Power; DVD Playback, Presentation and Super Long Life Sample power usage modes The power usage mode in the Windows®operating system under AC power is Full Power only. The properties of each mode are set in the Toshiba Power Management utility. 5.375 x 8.
Hot Keys Stand by mode 189 Stand by mode Fn + This hot key puts the computer into Stand by mode. ❖ A message box is displayed by default to confirm that the computer is going into Stand by mode. This message box can be set so it doesn’t display. Sample Stand by confirmation box ❖ For more information about Stand by mode, please see “Using Standby Mode” on page 107. 5.375 x 8.375 ver 2.
Hot Keys Hibernation mode Hibernation mode Fn + This hot key puts the computer into Hibernation mode. ❖ If Hibernation mode is enabled (the default) a message box is displayed by default to confirm the computer is going into Hibernation mode. The message box can be set so it doesn’t display. Sample Hibernation confirmation box ❖ If Hibernation mode is disabled, this hot key will not respond. For more information on Hibernation mode, see “Using Hibernation” on page 104. 5.375 x 8.375 ver 2.
Hot Keys Display modes 191 Display modes Fn + This hot key cycles through the power-on display options.
Hot Keys Enabling a wireless device Enabling a wireless device Fn + This hot key enables/disables the optional wireless devices in your computer. The wireless mode is: Wi-Fi enabled—This enables the Wi-Fi antenna Sample enabling a wireless device Disabling or enabling the TouchPad Fn + This hot key enables/disables the TouchPad. To use the TouchPad, see “Disabling or enabling the TouchPad” on page 57. Sample disable and enable TouchPad windows 5.375 x 8.375 ver 2.
Hot Keys Keyboard hot keys 193 Keyboard hot keys F10 + and off. Fn + off. Fn F11 This hot key turns the cursor control overlay on This hot key turns the numeric overlay on and F12 + off. Fn This hot key turns the scroll lock feature on and For more information, see “Overlay keys” on page 81. 5.375 x 8.375 ver 2.
Appendix B Power Cord/Cable Connectors Your notebook computer features a universal power supply you can use worldwide. This appendix shows the shapes of the typical AC power cord/cable connectors for various parts of the world. USA and Canada United Kingdom UL approved CSA approved BS approved Australia Europe AS approved VDA approved NEMKO approved 194 5.375 x 8.375 ver 2.
Appendix C Using ConfigFree™ with your Toshiba Computer ConfigFree™ is a set of utilities that makes it easy to control communication devices and network connections. ConfigFree also lets you identify communication problems and create profiles for easy switching between locations and communication networks. The ConfigFree utilities include the following: ❖ Connectivity Doctor—The Connectivity Doctor utility is used to analyze network connections and fix networking problems with your notebook computer.
Using ConfigFree™ with your Toshiba Computer Getting Started Getting Started This section contains information about the ConfigFree main screen, and how to start and setup ConfigFree. For more detailed information on setting up and using ConfigFree, see the Help File included in the application. Starting ConfigFree To start ConfigFree, be sure the computer has a wired or wireless connection.
Using ConfigFree™ with your Toshiba Computer ConfigFree Utilities 197 Wireless LAN Bluetooth Connectivity Doctor Profiles Sample ConfigFree Launcher ConfigFree Utilities Connectivity Doctor The Connectivity Doctor lets you analyze your network connections and fix network-connection problems. Using Connectivity Doctor, you can view detailed network information by simply moving the mouse pointer.
Using ConfigFree™ with your Toshiba Computer ConfigFree Utilities Sample Connectivity Doctor screen Moving the mouse pointer over a wired or wireless network device icon displays information about the device, such as its IP address, subnet mask, and MAC address. A wireless network device also shows information such as the network SSID and the device’s Wired Equivalent Privacy (WEP) key settings. Sample viewing device information 5.375 x 8.375 ver 2.
Using ConfigFree™ with your Toshiba Computer ConfigFree Utilities 199 If a problem, or potential problem, is detected, a triangle containing an exclamation point appears in the Connectivity Doctor screen and an orange frame describes the relevant location. You can then view a possible cause and solution for the problem by clicking the exclamation point.
Using ConfigFree™ with your Toshiba Computer ConfigFree Utilities Search for Wireless Devices The Search for Wireless Devices utility searches for wireless LAN devices and Bluetooth devices currently used in the neighborhood, and displays information about them on a virtual map. To search for wireless devices: 1 Click the icon in the system tray. 2 Click Search for Wireless Devices. A virtual map appears with a graphical representation of the wireless devices that have been detected.
Using ConfigFree™ with your Toshiba Computer ConfigFree Utilities 201 Sample viewing Wi-Fi devices The following screen shows an example of Bluetooth devices that are detected. As with the Wi-Fi screen, moving the mouse pointer over a device icon displays information about the device. Sample viewing Bluetooth devices You can connect to devices shown on the Bluetooth map: 1 Click the icon of a Bluetooth device. 5.375 x 8.375 ver 2.
Using ConfigFree™ with your Toshiba Computer ConfigFree Utilities 2 Click your own computer at the center of the map. 3 Configured devices are automatically connected. Devices not yet configured launch the Add New Connection Wizard, where you can configure and connect to the device. Profile Settings The Profile Settings utility lets you save network settings in “profiles.” ConfigFree profiles are useful for easily switching network settings and devices.
Using ConfigFree™ with your Toshiba Computer ConfigFree Utilities 203 ❖ Personal firewall settings for Internet connections. ❖ Dial-up connection settings for the default connection. ❖ File and printer sharing settings. ❖ Printer settings for the default printer. To create a profile: 1 Click the icon in the system tray. 2 Move the pointer to Profile. 3 Click Add. The Add Profile screen appears. 4 Select Capture and click OK. The Add Profile screen appears.
Using ConfigFree™ with your Toshiba Computer ConfigFree Utilities Sample Add Profile screen NOTE The online help provides real-world examples of setting up profiles for different networking environments. After you set up one or more profiles, you can check their settings and fine-tune them as necessary. Profiles can also be imported and exported. This feature is useful when transferring profile settings to other computers.
Using ConfigFree™ with your Toshiba Computer ConfigFree Utilities 205 To connect to a Toshiba Wireless Projector: 1 Click the icon in the system tray. 2 Move the mouse pointer to Toshiba Wireless Projector (DPJ), then click Connect. Launching Quick Connect prevents you from using the network to connect to a Toshiba Wireless Projector when the wireless LAN Configuration is set to Ad hoc. If you are connected to an access point, the connection is broken and reestablished later.
Using ConfigFree™ with your Toshiba Computer ConfigFree Utilities Sample Projector icon when connected with Quick Connect If the wireless mode for the wireless setting is set for 5 GHz (802.11a), Quick Connect changes this mode to 2.4 GHz (802.11b) and then connects to the projector. The wireless LAN configuration returns to the settings that were last used before the Quick Connect function was started: ❖ If the Toshiba Wireless Projector utility is closed.
Using ConfigFree™ with your Toshiba Computer Using the Automatic Switch 207 Using the Automatic Switch The Automatic Switch feature allows the computer to automatically switch profiles the next time it is powered on. This feature is particularly useful if you want your computer to automatically switch from the network configuration you use in your office to the one you use at home. The Auto Switch feature contains options for automatically switching between wired and wireless devices.
Using ConfigFree™ with your Toshiba Computer Semi-Automatic Switch Feature Semi-Automatic Switch Feature The Semi-Automatic feature alerts you when the computer connects to a Service Set Identifier (SSID) stored in a profile, When the computer connects to the designated SSID, a notification window appears. You can then click this window to connect using the settings specified in the profile. To use the Semi-Automatic Switch feature: 1 Right-click the icon in the system tray. 2 Click Auto Switch.
Glossary TECHNICAL NOTE: Some features defined in this glossary may not be available on your computer. Acronyms The following acronyms may appear in this user’s guide.
Glossary DMA direct memory access DIMM dual inline memory module DOS disk operating system DPI dots per inch DSTN dual supertwist nematic DVD digital versatile (or video) disc DVD-ROM digital versatile (or video) disc read-only memory ECP enhanced capabilities port EPROM erasable programmable read-only memory FAT file allocation table FCC Federal Communications Commission FIR fast infrared GB gigabyte HDD hard disk drive HTML Hypertext Markup Language IEEE Institute of Ele
Glossary 211 PCMCIA Personal Computer Memory Card International Association RAM random access memory RFI radio frequency interference ROM read-only memory RTC real-time clock SCSI small computer system interface SDRAM synchronous dynamic random access memory SRAM static random access memory SVGA super video graphics adapter TFT thin film transistor USB universal serial bus URL uniform resource locator WAN wide area network www World Wide Web Terms The following terms may appear
Glossary alternating current (AC) — The type of power usually supplied to residential and commercial wall outlets. AC reverses its direction at regular intervals. Compare direct current (DC). application — A computer program that you use to perform tasks of a specific type. Applications include word processors, spreadsheets, and database management systems. See also program. B backup — A copy of a file, usually on a removable disk, kept in case the original file is lost or damaged.
Glossary 213 bus — An electrical circuit that connects the central processing unit (CPU) with other parts of the computer, such as the video adapter, disk drives, and ports. It is the pathway through which data flows from one device to another. See also bus speed, frontside bus. bus speed — The speed at which the central processing unit (CPU) communicates with the other parts of the computer. byte — A sequence of eight bits. A byte is the smallest addressable unit of data.
Glossary compatibility — The extent to which computers, programs, or devices can work together harmoniously, using the same commands, formats, or language as another. configuration — (1) The collection of components that make up a single computer system. (2) How parts of the system are set up (that is, configured). controller — A device that controls the transfer of data from a computer to a peripheral device and vice versa.
Glossary 215 disable — To turn a computer option off. See also enable. disc — A round, flat piece of metal, designed to be read from and written to by optical (laser) technology, and used in the production of optical discs, such as CDs and DVDs. Compare disk. disk — A round, flat piece of material that can be magnetically influenced to hold information in digital form, and used in the production of magnetic disks, such as diskettes and hard disks. Compare disc. See also diskette, hard disk.
Glossary DVD-ROM (digital versatile [or video] disc read-only memory) — A very high-capacity storage medium that uses laser optics for reading data. Each DVD-ROM can hold as much data as several CD-ROMs. Compare CD-ROM. E emulation — A technique in which a device or program imitates another device or program. enable — To turn on a computer option. See also disable. executable file — A computer program that is ready to run. Application programs and batch files are examples of executable files.
Glossary 217 function keys — The keys labeled F1 through F12, typically located on the keyboard. Their function is determined by the operating system and/or individual programs. G gigabyte (GB) — A unit of data equal to 1,073,741,824 bytes (1024 x 1024 x 1024 bytes). See also byte. ground — A conductor to which all components of an electric circuit are connected. It has a potential of zero (0) volts, is connected to the earth, and is the point of reference for voltages in the circuit.
Glossary interlaced — A method of refreshing a computer screen, in which only every other line of pixels is refreshed. Interlaced monitors take two passes to create a complete screen image. Compare non-interlaced. internal device — See device. Internet — The decentralized, world-wide network of computers that provides electronic mail, the World Wide Web, and other services. See also World Wide Web.
Glossary M 219 megabyte (MB) — A unit of data equal to 1,048,576 bytes (1024 x 1024 bytes). See also bytes. memory — Typically refers to the computer’s main memory, where programs are run and data is temporarily stored and processed. Memory can be volatile and hold data temporarily, such as RAM, or it can be nonvolatile and hold data permanently, such as ROM. A computer’s main memory is RAM. See RAM, ROM. microprocessor — See central processing unit (CPU).
Glossary NT file system (NTFS) — An advanced file system designed for use specifically with the Windows NT operating system. O online — Available through the computer. Online may refer to information being read from your own computer’s hard disk, such as online documentation or online help, or to information coming from another company on a company network or the Internet. operating system — A set of programs that controls how the computer works.
Glossary 221 processor — See central processing unit (CPU). program — A set of instructions that can be executed by a computer. The general classes of programs (also called software) are operating system, application, and utility. See also operating system, application, utility. properties — The attributes of an object or device. For example, the properties of a file include the file’s type, size, and creation date. R RAM (random access memory) — Volatile memory that can be written to as well as read.
Glossary ROM (read-only memory) — Non-volatile memory that can be read but not written to. By non-volatile, we mean that information in ROM remains whether or not the computer is receiving power. This type of memory is used to store your computer’s BIOS, which is essential instructions the computer reads when you start it up. See also BIOS, memory. Compare RAM. S select — To highlight or otherwise specify text, data, or graphics with the intent to perform some operation on it.
Glossary U 223 universal serial bus (USB) 2.0— A serial bus that supports a data transfer rate of up to 480 Mbps (480 million bits per second). USB can connect up to 127 peripheral devices through a single allpurpose USB port. USB allows hot swapping of peripherals. See also bus, hot swapping, serial. upload — To send a file to another computer through a modem or network. See also download. USB — See universal serial bus (USB).
Index A buttons CD Player 96 DVD-ROM or multi-function drive eject 91 AC power light 52 audio features 144 Auto-Run 97 avoiding injury 41 C B battery caring for 125 changing 122 charge not lasting 167 charging 73, 113, 114 conserving power 119 disposal 127 installing 122 light 52 not charging 167 power usage hot key 121 power usage mode 188 removing 122 Bridge Media slot 150 button start 131 Card and Socket Services 147 CD creating 97 playing using Auto-Run 97 CD and DVDs caring for 99 viewing contents
CD or DVDs 99 computer 74 click 57 comfort chair 43 lighting 43 work habits 44 commands powering down 100 communications network connection 136 system resources 162 compact discs inserting 93 problem solving 173 removing 98 computer cleaning 74 lock 75 moving 75 non-system disk or disk error message 158 placement 42 precautions 45 protection 40 running on battery power 111 setting up 47, 59 turning off 101, 105, 108 turning on 55 warning resume failure message 158 work area 40 computing tips 77 connecti
external monitor not working 170 latch 54 screen is blank 169 display device external 70 display output settings 71 display panel closing 74 opening 54 Display settings hot key 143 display, external adjusting 72 disposal information 27 disposing of used batteries 127 DMA (Direct Memory Access) 163 double-click 57 DVD-ROM or multi-function drive eject button 91 inserting discs 93 DVD-ROM or multifunction drive can’t access disc 173 control buttons 92 inserting a disc 93 removing 98 removing a disc 98 E
resolving 163 Help 161 Hibernate restarting 106 using 104 Hibernation mode 73, 100 configuring 104 hot key display modes 191 display settings 143 power usage mode 188 Stand by mode 189 volume mute 185 wireless mode 192 hot key power usage mode 121 hot keys instant password 186 keyboard functions 193 hot swapping 147 precautions 149 I i.
M main battery changing 122 removing 122 memory expansion slots 59 problem solving 166 removing 62 removing expansion slot cover 60 memory module inserting 60 removing 63 Memory Stick inserting 150 removing 151 modem determining COM port 134 problem solving 179 resetting port to default settings 134 upgrading 134 module Wi-Fi Mini PC 138 monitor 70 connecting 70 not working 169 mouse connecting 63 installing 63 serial 63 moving the computer 75 N network accessing 136 dial-up connection 136 Dial-Up Netw
hot key 121 powering down using Standby 107 powering off 100 precautions 45 primary button 57 printer Add Printer Wizard 65 problem solving 178 printing a file 88 problem solving AC power 167 battery charge doesn’t last 167 battery not charging 167 can’t access disc 173 changing display properties 170 checking device properties 165 compact discs not running correctly 173 computer hangs when PC Card inserted 176 computer will not power up 158 contacting Toshiba 181, 182 corrupted/damaged data files 172 D
URL address not found 161 using Startup options 159 warning resume failure 158 Windows XP not working 159 programs not running correctly 172 starting 83 projector 70 connecting 70 protection of stored data 2 R recharging main battery 113, 114 recording adjusting quality 145 sounds 144 Recovery media 38 recycle bin icon 131 removing CDs and DVDs 98 main battery 122 PC Cards 148 restarting from Hibernate 106 restarting from Turn Off 102 RJ-11 jack 135 Run dialog box 85 running the computer on battery pow
system tray 132 T taskbar 132 television adjusting display 72 Toshiba Forum 182 Internet Web sites 183 online services 182 traveling tips 128 Turn Off restarting from 102 using 105, 108 turning computer on/off 55, 101, 105, 108 turning off the computer 100 U Universal Resource Locator (URL) 132 USB mouse connecting 63 using Hibernate 104 PC Cards 147 Standby 108 using a file extension 87 V video features exploring 142 video projector adjusting display 72 video-out S-video 70 volume mute hot key 185