Satellite P30 Series TOSHIBA Satellite P30 Series User's Manual
Copyright © 2004 by TOSHIBA Corporation. All rights reserved. Under the copyright laws, this manual cannot be reproduced in any form without the prior written permission of TOSHIBA. No patent liability is assumed, with respect to the use of the information contained herein. TOSHIBA Satellite P30 Series Portable Personal Computer User's Manual First edition August 2004 Disclaimer This manual has been validated and reviewed for accuracy.
Macrovision License of Notice This product incorporates copyright protection technology that is protected by methods and claims of certain U.S. patents and other intellectual rights owned by Macrovision Corporation, and other rights owners. Use of this copyright protection technology must be authorized by Macrovision Corporation and is intended for home and other limited viewing uses only unless authorized by Macrovision Corporation. Reverse engineering or disassembly is prohibited.
■ To remove power from the computer, turn it off, remove the battery, and disconnect the AC adapter from the electrical outlet. ■ To help avoid the potential hazard of electric shock, do not connect or disconnect any cables or perform maintenance or reconfiguration of this product during an electrical storm. ■ When setting up the computer for work, place it on a level surface. ■ Do not dispose of batteries in a fire as they may explode. Check with local authorities for disposal instructions.
■ Do not use this product near water, for example, near a bathtub, washing bowl, kitchen sink or laundry tub, in a wet basement or near a swimming pool. ■ Avoid using a telephone (other than a cordless type) during an electrical storm. There may be a remote risk of electric shock from lightning. ■ Do not use the telephone to report a gas leak in the vicinity of the leak. ■ Use only the power cord indicated in this manual.
EMC Regulatory Information Contact Address: TOSHIBA America Information Systems, Inc. 9740 Irvine Boulevard Irvine, California 92618-1697 Telephone: (949)583-3000 EU Declaration of Conformity TOSHIBA declares, that the product: Satellite P30 conforms to the following Standards: Supplementary Information: "The product complies with the requirements of the Low Voltage Directive 73/23/EEC and the EMC Directive 89/336/EEC and/or the R&TTE Directive 1999/05/EEC.
Optical Disc Drive Safety Instruction ■ Be sure to check the international precautions at the end of this section. The optical drive that is used in this computer is equipped with a laser device. The classification label with the following sentence is affixed to the surface of the drive.
International precautions ■ This drive employs a laser system. To ensure proper use of this product, please read this instruction manual carefully and retain for future reference. Should the unit ever require maintenance, contact an authorized service location. ■ Use of controls, adjustments or the performance of procedures other than those specified may result in hazardous radiation exposure. ■ To prevent direct exposure to the laser beam, do not try to open the enclosure.
VORSICHT: Dieses Gerät enthält ein LaserSystem und ist als "LASERSCHUTZKLASSE 1 PRODUKT" klassifiziert. Für den richtigen Gebrauch dieses Modells lesen Sie bitte die Bedienungsanleitung sorgfältig durch und bewahren diese bitte als Referenz auf. Falls Probleme mit diesem Modell auftreten, benachrichtigen Sie bitte die nächste "autorisierte Service-Vertretung". Um einen direkten Kontakt mit dem Laserstrahl zu vermeiden darf das Gerät nicht geöffnet werden.
Modem warning notice Conformity Statement The equipment has been approved to [Commission Decision "CTR21"] for pan- European single terminal connection to the Public Switched Telephone Network (PSTN). However, due to differences between the individual PSTNs provided in different countries/regions the approval does not, of itself, give an unconditional assurance of successful operation on every PSTN network termination point.
Redial Up to two redial attempts can be made. If more than two redial attempts are made, the modem will return Black Listed. If you are experiencing problems with the Black Listed code, set the interval between redials at one minute or longer. Japan's Telecommunications Business Law permits up to two redials on analogue telephones, but the redials must be made within a total of three minutes. The internal modem is approved by Japan Approvals Institute for Telecommunications Equipment.
If problems arise If any of your telephone equipment is not operating properly, you should immediately remove it from your telephone line, as it may cause harm to the telephone network. If the telephone company notes a problem, they may temporarily discontinue service. When practical, they will notify you in advance of this disconnection. If advance notice is not feasible, you will be notified as soon as possible.
Instructions for IC CS-03 certified equipment 1. NOTICE: The Industry Canada label identifies certified equipment. This certification means that the equipment meets certain telecommunications network protective, operational and safety requirements as prescribed in the appropriate Terminal Equipment Technical Requirements document(s). The Department does not guarantee the equipment will operate to the user's satisfaction.
Important Notice Copyrighted works including, but not limited to music, video, computer programs and databases are protected by copyright laws. Unless specifically permitted under applicable copyright laws, you cannot copy, modify, assign, transmit or otherwise dispose of any copyrighted work without the consent of the owner of the copyright.
PC Card overheating Some PC Cards can become hot with prolonged use. If two cards are installed, both can become hot even if only one is used extensively. Overheating of a PC Card can result in errors or instability in the PC Card operation. Also be careful when you remove a PC Card that has been used for a long time. Mobile phones Use of mobile phones can interfere with the audio system.
Satellite P30 Series Table of Contents Preface ...........................................................................................xxii Chapter 1 Introduction Equipment checklist. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-1 Hardware . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-1 Software . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-2 Documentation . . . . . . . . . . .
Table of Contents Optical Media drive. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-10 Region codes for DVD drives and media . . . . . . . . . . . . . . . . . . . . 2-10 Writable discs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-10 CDs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-10 DVDs. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Table of Contents Writing CD/DVDs on a DVD±R/±RW drive and a DVD±R/±RW drive supporting Double Layer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-9 Important message . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-9 Disclaimer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-9 Before writing or rewriting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Table of Contents Chapter 5 The Keyboard Typewriter keys. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . F1 ... F12 function keys . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Soft keys: Fn key combinations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Emulation keys . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Hotkeys . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Table of Contents Chapter 7 Optional Devices PC cards . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-2 Installing a PC card. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-2 Removing a PC card. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-3 SD/MMC/SM/MS/MS Pro/xD Memory Cards . . . . . . . . . . . . . . . . . . . . 7-4 Installing an Memory card. . . . . . . . . . . . . . . . . . . . . . . . . . . .
Table of Contents Modem . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . LAN . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Wireless LAN . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Monitor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . i.LINK (IEEE1394). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Satellite P30 Series Preface Congratulations on your purchase of the Satellite P30 computer. This powerful notebook computer provides excellent expansion capability, including multimedia devices, and it is designed to provide years of reliable, high-performance computing. This manual tells how to set up and begin using your Satellite P30 computer. It also provides detailed information on configuring your computer, basic operations and care, using optional devices and troubleshooting.
Manual contents This manual has eight chapters, three appendixes and a Glossary. Chapter 1, Introduction, is an overview of the computer's special features, utilities, and options. Chapter 2, The Grand Tour, identifies the components of the computer and briefly explains how they function. Chapter 3, Getting Started, provides a quick overview of how to begin operating your computer and gives tips on safety and designing your work area.
Keys The keyboard keys are used in the text to describe many computer operations. A distinctive typeface identifies the key top symbols as they appear on the keyboard. For example, Enter identifies the Enter key. Key operation Some operations require you to simultaneously use two or more keys. We identify such operations by the key top symbols separated by a plus sign (+). For example, Ctrl + C means you must hold down Ctrl and at the same time press C.
Satellite P30 Series Chapter 1 Introduction This chapter provides an equipment checklist, and it identifies the computer's special features, options and accessories. Basic features are described in a separate pamphlet. Some of the features described in this manual may not function properly if you use an operating system that was not preinstalled by TOSHIBA. Equipment checklist Carefully unpack your computer. Save the box and packing materials for future use.
Introduction Software ■ The following software preinstalled on your hard disk: Microsoft® Windows® XP TOSHIBA Utilities Display Driver Touch pad driver Sound driver Miscellaneous drivers (depending on the model you purchased these will include drivers for devices such as the modem, LAN, wireless LAN and Multiple Digital Media Card Slot) ■ Online help ■ Product Recovery Disk ■ TOSHIBA Tools & Utilities CD-ROM ■ ■ ■ ■ ■ ■ The system may not function properly if you use drivers that are not preinstalled or d
Introduction Features The Satellite P30 series computer uses TOSHIBA's advanced Large Scale Integration (LSI), Complementary Metal-Oxide Semiconductor (CMOS) technology extensively to provide compact size, minimum weight, low power usage, and high reliability. This computer incorporates the following features and benefits: Processor Intel® Celeron® Processor up to 2.8 GHz Intel® Celeron® D Processor 325/330/335 or higher Mobile Intel® Pentium® 4 Processor 2.8GHz/ 3.
Introduction Memory Slot Two DDR SODIMM sockets with support for 256MB/512MB/1GB modules Two DDR SODIMM sockets with support for 256MB/512MB/1GB modules L2 Cache 128KB L2 Cache (Intel® Celeron® Processor up to 2.8GHz) 256KB L2 Cache (Intel® Celeron® D Processor 325/330/335 or higher) 512KB L2 Cache (Mobile Intel® Pentium® 4 Processor up to 3.
Introduction Power Battery Pack 12-cell Li-Ion smart battery pack with 14.8V*6450mAh capacity or 8-cell Li-Ion smart battery pack with 14.8V*4300mAh capacity (depending on the model) Approximately 12 hours or longer charging time to 100% battery capacity (system on). Approximately 4 hours charging time to 100% battery capacity (system off) Approximately 3 days discharge time in Standby Mode for the 12-cell battery and 2 days for the 8cell battery.
Introduction Disks User’s Manual Fixed hard disk Either one 40GB/60GB/80GB/100GB or larger capacity hard drive Bus Master IDE 9.5m/m 2.5" HDD Support Ultra DMA 100 CD-RW/DVD-ROM drive Some models are equipped with a full-size CDRW/DVD-ROM module that lets you record data to rewritable CD-Rs and CD-RWs as well as run either 12cm (4.72") or 8cm (3.15") CD/DVDs without using an adaptor. It reads DVD-ROMs at a maximum 8 speed and CD-ROMs at a maximum 24 speed.
Introduction DVD±R/±RW (DVD Dual) drive supporting Double Layer User’s Manual Some models are equipped with a full-size DVD Dual module that lets you record data to rewritable CD/DVDs as well as run either 12cm (4.72") or 8cm (3.15") CD/DVDs without using an adaptor. It reads DVD-ROMs at a maximum 8 speed and CD-ROMs at a maximum 24 speed.
Introduction DVD±R/±RW (DVD Dual) drive User’s Manual Some models are equipped with a full-size DVD Dual module that lets you record data to rewritable CD/DVDs as well as run either 12cm (4.72") or 8cm (3.15") CD/DVDs without using an adaptor. It reads DVD-ROMs at a maximum 8 speed and CD-ROMs at a maximum 24 speed. It writes CD-Rs at up to 16 speed, CD-RWs at a maximum 10 speed, DVD-Rs and DVD+Rs at a maximum 4 speed, and DVD-RWs and DVD+RWs at a maximum 2 speed.
Introduction DVD Super Multi drive supporting Double Layer User’s Manual Some models are equipped with a full-size DVD Super Multi drive module that lets you record data to rewritable CD/DVDs as well as run either 12cm (4.72") or 8cm (3.15") CD/DVDs without using an adaptor. It reads DVD-ROMs at a maximum 8 speed and CD-ROMs at a maximum 24 speed.
Introduction DVD Super Multi drive Some models are equipped with a full-size DVD Super Multi drive module that lets you record data to rewritable CD/DVDs as well as run either 12cm (4.72") or 8cm (3.15") CD/DVDs without using an adaptor. It reads DVD-ROMs at a maximum 8 speed and CD-ROMs at a maximum 24 speed. It writes CD-Rs at up to 16 speed, CDRWs at up to 8 speed, DVD-Rs at maximum 4 speed, DVD-RWs and DVD-RAM at maximum 2 speed, and DVD+Rs and DVD+RWs at maximum 2.4 speed.
Introduction Slots PC Card The computer is equipped with one Type II PC Card slot MODEM/LAN card PC Card 8.0 Compliant, supports 3V and 5V cards Multiple Digital Media Card (SD/ MMC/SM/MS/MS Pro/ xD) This slot lets you easily transfer data from devices, such as digital cameras and Personal Digital Assistants, that use flash-memory. You can use memory module in this slot Ports (depending on configuration) External monitor 15-pin analog VGA port supports VESA DDC2B compatible functions.
Introduction Communications Modem An internal modem provides capability for data and fax communication. It supports V.90 or V.92 depending on the region. The speed of data and fax transfer depends on the analog telephone line conditions. It has a modem jack for connecting to a telephone line.
Introduction Special features The following features are either unique to TOSHIBA computers or are advanced features, which make the computer more convenient to use. User’s Manual Hotkeys Key combinations let you quickly modify the system configuration directly from the keyboard without running a system configuration program. Display Automatic Power off This feature automatically cuts off power to the internal display when there is no input from the keyboard or pointing device for a time specified.
Introduction Low Battery Automatic Hibernation When battery power is exhausted to the point that computer operation cannot be continued, the system automatically enters Hibernation Mode and shuts down. You can activate this setting in the TOSHIBA Power Saver utility. Hibernation This feature lets you turn off the power without exiting from your software. The contents of main memory are saved to the hard disk. When you turn on the power again, you can continue working right where you left off.
Introduction Utilities This section describes the preinstalled utilities and gives advice on how to start them. For details on specific operations, refer to each utility's online manual, help files or readme files. User’s Manual TOSHIBA Power Saver There are two ways to display the Windows XP Control Panel. The default is Category View. TOSHIBA Power Saver utility is under the Performance and Maintenance item.
Introduction User’s Manual TOSHIBA Touch pad On/Off Utility Pressing Fn+F9 in a Windows environment enables or disables the Touch pad function. When you press these hot keys, the current setting will change and be displayed as an icon. RecordNow! Basic for TOSHIBA You can create CD/DVDs in several formats including audio CDs that can be played on a standard stereo CD player and data CD/DVDs to store the files and folders on your hard disk drive.
Introduction Options You can add a number of options to make your computer even more powerful and convenient to use. The following options are available: Memory Modules Two memory modules can be installed in the computer The computer comes with at least one memory module pre-installed. Use only PC2700 compatible DDR memory modules. See your TOSHIBA dealer for details User’s Manual Battery Pack An additional battery pack can be purchased from your TOSHIBA dealer.
Satellite P30 Series Chapter 2 The Grand Tour This chapter identifies the various components of your computer. Become familiar with each component before you operate the computer. Certain notebook chassis are designed to accommodate all possible configurations for an entire product series. Your selected model may not have all the features and specifications corresponding to all of the icons or switches shown on the notebook chassis, unless you have selected all those features.
The Grand Tour Power LED The Power LED flashes amber while the system is in Standby mode. The LED turns off when the computer is turned off or in hibernation mode. In normal operating mode, the LED is green. Battery LED The Battery LED indicates the battery's current charge/discharge status. It lights green when the battery is fully charged. It lights amber while the battery is being charged from the AC adapter. It flashes amber when the battery capacity is low.
The Grand Tour Right side The following figure shows the computer right side PC Card Slot i.Link port Multiple digital media card slot Volume control Universal Serial Bus (USB) Port Headphone Jack Wireless Communication Switch Microphone Jack Wireless LED The right side of the computer * Some models are not equipped with Wireless Communication Switch. * i.LINK is provided with some models. User’s Manual PC Card Slot A PC Card slot can accommodate one 5 mm PC Card (Type II).
The Grand Tour Microphone Jack A standard 3.5 mm mini microphone jack enables connection of a three conductive type mini-jack for a monaural microphone. Wireless Communication The Wireless Communication Switch turns on the wireless networking transceiver. The Wireless Communication LED next to Wireless communication switch indicates that wireless networking is turned on. Back side The following figure shows the computer back panel.
The Grand Tour LAN Jack This jack lets you connect to a LAN. The adaptor has built-in support for Ethernet LAN (10 megabits per second, 10BASE-T) and Fast Ethernet LAN (100 megabits per second, 100BASE-TX). Modem Jack In areas where an internal modem is installed as standard equipment, there is a modem jack that lets you use a modular cable to connect the modem directly to a telephone line. The modem is not supported in some marketing regions.
The Grand Tour Battery Double Lock When you slide this latch to the position of lock, the battery can not be released even you have slid the battery latch. Battery Latch Slide this latch to remove the battery pack. Front with the display open The following figure shows the front of the computer with the display open. To open the display, slide the display latch on the front of the display and lift up.
The Grand Tour Power Button Press the power button to turn the computer's power on and off. There is one LED inside of power button. The power button will shinning blue when the system is accessed. Left and Right Speakers The audio speakers. TouchPad A pointer control device located in the center of the palm rest is used to control the on-screen pointer. Refer to the Using the TouchPad section in Chapter 4, Operating Basics.
The Grand Tour Display Screen The LCD displays high-contrast text and graphics at up to 2048x1536 pixel. Refer to Appendix B, Display Modes. When the computer operates on the AC adaptor the display screen's image will be somewhat brighter than when it operates on battery power. The brightness level is intended to save battery power. To prolong the life of your display screen, use a screen saver when you're not working the computer and it is idle.
The Grand Tour Keyboard Indicators Caps Lock Arrow Mode Caps Lock User’s Manual Numeric Mode Caps Lock Arrow Mode When the Arrow mode icon lights green, you can use the keypad overlay (light gray labeled keys) as cursor keys. Refer to the Keypad Overlay section in Chapter 5, The Keyboard. Numeric Mode You can use the keypad overlay (light gray labeled keys) for numeric input when the Numeric mode icon lights green. Refer to the Keypad Overlay section in Chapter 5, The Keyboard.
The Grand Tour Optical Media drive One of the following optical media drives is installed in the computer: CD-RW/ DVD-ROM drive, DVD-ROM drive, DVD-R/-RW drive, DVD±R/ ±RW drive, DVD Super Multi drive. An ATAPI interface controller is used for CD/DVD-ROM operation. When the computer is accessing a CD/DVD, an indicator on the drive glows.
The Grand Tour Formats The drives support the following formats ■ DVD-ROM ■ DVD-Video ■ CD-DA ■ CD-Text ■ Photo CD™ (single/multi■ CD-ROM Mode 1, Mode 2 session ■ CD-ROM XA Mode 2 (Form1, ■ Enhanced CD (CD-EXTRA) Form2) ■ CD-RW/DVD-ROM drive The full- size CD-RW/DVD-ROM drive module lets you record data to rewritable CD/ DVDs as well as run either 12 cm (4.72") or 8 cm (3.15") CD/ DVDs without using an adaptor. The read speed is slower at the center of a disc and faster at the other edge.
The Grand Tour DVD±R/±RW (DVD Dual) drive The full- size DVD±R/±RW drive module lets you record data to rewritable CD/ DVDs as well as run either 12 cm (4.72") or 8 cm (3.15") CD/DVDs without using an adaptor. The read speed is slower at the center of a disc and faster at the other edge. DVD read 8 speed (maximum) DVD-R write 4 speed (maximum) DVD-RW write 2 speed (maximum) DVD+R write 4 speed (maximum) DVD+RW write 2.
The Grand Tour DVD Super Multi drive The full-siza DVD super multi drive module lets you record data to rewritable CD/DVDs as well as run either 12cm(4.72") or 8cm(3.15") CD/ DVDs without using an adaptor. The read speed is slower at the center of a disc and faster at the other edge. DVD read 8 speed (maximum) DVD-R write 4 speed (maximum) DVD-RW write 2 speed (maximum) DVD+R write 2.4 speed (maximum) DVD+RW write 2.
The Grand Tour AC adaptor The AC adaptor converts AC power to DC power and reduces the voltage supplied to the computer. It can automatically adjust to any voltage from 100 to 240 volts and to a frequency of either 50 or 60 hertz, enabling you to use the computer in almost any country/region. To recharge the battery, simply connect the AC adaptor to a power source and the computer. See Chapter 4, Operating Basics, for details. The AC adaptor Use of the wrong adaptor could damage your computer.
Satellite P30 Series Chapter 3 Getting Started This chapter provides basic information to get you started using your computer. It covers the following topics: ■ Setting up your work space - for your health and safety Be sure also to read Instruction Manual for Safety & Comfort. This guide, which is included with the computer, explains product liability.
Getting Started General conditions In general, if you are comfortable, so is your computer, but read the following to make sure your work site provides a proper environment. ■ TOSHIBA Power SaverMake sure there is adequate space around the computer for proper ventilation. ■ Make sure the AC power cord connects to an outlet that is close to the computer and easily accessible.
Getting Started Seating and posture The height of your chair in relation to the computer and keyboard as well as the support it gives your body are primary factors in reducing work strain. Refer to the following tips and to figure. 90 1 Posture and positioning of the computer ■ Place your chair so that the keyboard is at or slightly below the level of your elbow. You should be able to type comfortably with your shoulders relaxed. ■ Your knees should be slightly higher than your hips.
Getting Started Work habits A key to avoiding discomfort or injury from repetitive strain is to vary your activities. If possible, schedule a variety of tasks into your work day. If you must spend long periods at the computer, finding ways to break up the routine can reduce stress and improve your efficiency. ■ Sit in a relaxed posture. Good positioning of your chair and equipment as described earlier can reduce tension in your shoulders or neck and ease back strain. ■ Vary your posture frequently.
Getting Started Connecting the AC adaptor Attach the AC adaptor when you need to charge the battery or you want to operate from AC power. It is also the fastest way to get started, because the battery pack will need to be charged before you can operate from battery power. The AC adaptor can be connected to any power source supplying from 100 to 240 volts and 50 or 60 hertz. For details on using the AC adaptor to charge the battery pack, refer to Chapter 6, Power and Power-Up Modes.
Getting Started Opening the display ReW ritab le High Speed The display panel can be rotated in a wide range of angles for optimal viewing. 1. Slide the display latch on the front of the computer to the right to unlatch the display panel. Opening the display 2. Lift the panel up and adjust it to the best viewing angle for you. Use reasonable care when opening and closing the display panel. Opening it vigorously or slamming it shut could damage the computer.
Getting Started Turning on the power This section describes how to turn on the power. After you turn on the power for the first time, do not turn it off until you have set up the operating system. Refer to the section Starting up for the first time in this chapter. 1. Make sure the diskette drive(optional) is empty. If a diskette is in the drive, press the eject button and remove the diskette. 2. Open the display panel. 3. Press the computer's power button and release.
Getting Started Turning off the power The power can be turned off in one of the following modes: Shut down (Boot), Hibernation or Standby mode. Shut Down mode (Boot mode) When you turn off the power in Shut Down mode no data is saved and the computer will boot to the operating system's main screen. 1. If you have entered data, save it to the hard disk or to a diskette. 2. Make sure all disk activity has stopped, then remove the CD/DVD-ROM or diskette.
Getting Started Benefits of Hibernation The hibernation feature provides the following benefits: ■ Saves data to the hard disk when the computer automatically shuts down because of a low battery. For the computer to shut down in hibernation mode, the hibernation feature must be enabled in two places in TOSHIBA Power Saver: the Power Save Modes tab and the Advanced tab. Otherwise, the computer will shut down in Standby mode. If battery power becomes depleted, data saved in Standby will be lost.
Getting Started Data save in hibernation mode When you turn off the power in hibernation mode, the computer takes a moment to save current memory data to the hard disk. During this time, the Built-in HDD indicator will light. After you turn off the computer and memory is saved to the hard disk, turn off the power to any peripheral devices. Do not turn the computer or devices back on immediately. Wait a moment to let all capacitors fully discharge.
Getting Started Benefits of standby The standby feature provides the following benefits: ■ Restores the previous working environment more rapidly than does hibernation. ■ Saves power by shutting down the system when the computer receives no input or hardware access for the duration set by the System Standby feature. ■ You can use the panel power off feature. Executing standby You can also enable Standby by pressing Fn + F3. See Chapter 5, The Keyboard, for details.
Getting Started Restarting the computer Certain conditions require that you reset the system. For example, if: ■ You change certain computer settings. ■ An error occurs and the computer does not respond to your keyboard commands. There are three ways to reset the computer system: 1. Select Restart from the Turn Off Computer window in the start box. 2. If the computer is already on, press Ctrl + Alt + Del. 3.
Satellite P30 Series Chapter 4 Operating Basics This chapter gives information on basic operations including using the Touch pad, optical media drives, the internal modem, LAN, wireless LAN. It also provides tips on caring for your computer and on heat dispersal. Using the Touch pad To use the Touch pad, simply move your finger tip across it in the direction you want the on-screen pointer to go.
Operating Basics The Touch pad has similar functions to a two-button mouse with a scroll wheel. For some functions, you can tap the Touch pad instead of pressing a control button. You can customize pointing device actions in Mouse Properties. Open the Control Panel, select the Mouse icon and press Enter to open the Mouse Properties window. Click Click the left control button or tap the Touch pad one time. Double-click Click the left control button twice or tap the Touch pad twice.
Operating Basics Loading optical media discs To load a DVD/CD, follow the steps below and refer the following figures. 1. Turn on the power. 2. a. Press the eject button to open the drawer slightly. Pressing the eject button b. Pressing the eject button will not open the drawer when the computer's power is off. If the power is off, you can open the drawer by inserting a slender object (about 15 mm) such as a straightened paper clip into the eject hole just to the right of the eject button.
Operating Basics 4. Lay the DVD/CD, label side up, in the drawer. Inserting a DVD/CD Be careful not to touch the lens or the area around it. Doing so could cause the drive to malfunction. 5. Press gently at the center of the DVD/CD until you feel it click into place. The DVD/CD should lie below the top of the spindle, flush with its base. 6. Push the center of the drawer to close it. Press gently until it locks in place.
Operating Basics Removing optical media discs To remove the DVD/CD, follow the steps below and refer the following figure. Do not press the eject button while the computer is accessing the DVD drive. Wait for the Diskette/Optical Media indicator to go out before you open the drawer. Also, if the disc is spinning when you open it, wait for it to stop before you remove it. 1. To pop the drawer partially open, press the eject button. Gently pull the drawer out until it is fully opened.
Operating Basics CD/DVD Button The CD/DVD button can be defined upon user's preference. Once the button has been defined, activate this button will launch the application defined. If without specific definition it will launch CD/DVD only. Press CD/DVD or play buttons when the computer system power is off. If an audio CD is in the drive, the system enters CD playback mode and operates as a stand-alone CD player.
Operating Basics Writing CDs on a CD-RW/DVD-ROM drive You can use the CD-RW/DVD-ROM drive to write data to CD-R/RW discs. The following applications for writing are preinstalled: Record Now!/DLA, licensed by Sonic Solutions. Important message Before you write or rewrite to CD-R/RW disc, read and follow all setup and operating instructions in this section. If you fail to do so, the CD-RW/ DVD-ROM drive may not function properly, and you may fail to write or rewrite, lose data or incur other damage.
Operating Basics Before writing or rewriting Please observe the following points when you write or rewrite the data. ■ We recommend the following manufacturers of CD-R and CD-RW media. Media quality can affect write or rewrite success rates. CD-R: TAIYOYUDEN CO., LTD. MITSUBISHI CHEMICAL CORPORATION RICOH Co., Ltd. Hitachi Maxell Ltd. CD-RW: MITSUBISHI CHEMICAL CORPORATION RICOH Co., Ltd. TOSHIBA has confirmed the operation of CD-R and CD-RW media of the manufacturers above.
Operating Basics Writing CD/DVDs on a DVD±R/±RW drive and a DVD±R/ ±RW drive supporting Double Layer You can use the DVD±R/±RW drive to write data to either CD-R/RW or DVD-R/-RW/+R/+RW discs. The following applications for writing are preinstalled: Record Now!/DLA, licensed by Sonic Solutions. InterVideo WinDVD Creator 2 Platinum, which is a product of InterVideo, Inc.
Operating Basics Before writing or rewriting Please observe the following points when you write or rewrite data. ■ Based on TOSHIBA's limited compatibility testing, we suggest the following manufacturers of CD-R/RW or DVD-R/-RW/+R/+RW disc. However, in no event does TOSHIBA guarantee the operation, quality or performance of any disc. Disc quality can affect write or rewrite success rates. CD-R: TAIYOYUDEN CO., LTD. MITSUBISHI CHEMICAL CORPORATION RICOH Co., Ltd. Hitachi Maxell Ltd.
Operating Basics ■ Data deleted (erased) from a CD-RW and DVD-RW/+RW disc cannot be recovered. Check the content of the disc carefully before you delete it. If multiple drives that can write data to discs are connected, be careful not to delete data from the wrong drive. ■ In writing to a DVD-R/+R/-RW/+RW disc, some disc space is required for file management, so you may not be able to write the full capacity of the disc.
Operating Basics Writing CD/DVDs on a DVD Super Multi drive and a DVD Super Multi drive supporting Double Layer You can use the DVD Super Multi drive to write data to either CD-R/RW or DVD-R/-RW/+R/+RW/-RAM discs. The following applications for writing are preinstalled: Record Now!/DLA, licensed by Sonic Solutions.. InterVideo WinDVD Creator 2 Platinum, which is a product of InterVideo, Inc..
Operating Basics Before writing or rewriting Please observe the following points when you write or rewrite data. ■ Based on TOSHIBA's limited compatibility testing, we suggest the following manufacturers of CD-R/RW and DVD-R/+R/-RW/+RW/-RAM disc. However, in no event does TOSHIBA guarantee the operation, quality or performance of any disc. Disc quality can affect write or rewrite success rates. CD-R: TAIYOYUDEN CO., LTD. MITSUBISHI CHEMICAL CORPORATION RICOH Co., Ltd. Hitachi Maxell Ltd.
Operating Basics ■ You can use DVD-RAM discs that can be removed from a cartridge and DVD-RAM discs designed without a cartridge. You cannot use a disc with a 2.6 GB single-sided capacity or 5.2 GB double-sided capacity. ■ Other DVD-ROM drives for computers or other DVD players may not be able to read DVD-R/+R/-RW/+RW/-RAM discs. ■ Data written to a CD-R/DVD-R/+R disc cannot be deleted either in whole or in part. ■ Data deleted (erased) from a CD-RW and DVD-RW/+RW/-RAM disc cannot be recovered.
Operating Basics RecordNow! Basic for TOSHIBA Note the following limitations when you use RecordNow!: ■ DVD-Video cannot be created using RecordNow!. ■ DVD-Audio cannot be created using RecordNow!. ■ You cannot use RecordNow!'s "Audio CD for Car or Home CD Player" function to record music to the DVD-R/-RW or DVD+R/+RW disc. ■ Do not use the "Exact Copy" function of RecordNow! to copy DVDVideo and DVD-ROM with copyright protection.
Operating Basics Data Verification To verify that data is written or rewritten correctly, follow the steps below before you write or rewrite a Data CD/DVD. 1. Click the Options button ( ) on the RecordNow! Console to open the Options panels. 2. Select the Data in the left-side menu. 3. Mark the Verify data written to the disc after burning check box in the Data Options. 4. Click the OK button.
Operating Basics When WinDVD Creator Platinum is used: You can record video back to your digital camcorder via i.LINK (IEEE1394) using WinDVD Creator Platinum. However, there is a case where its playback sound is choppy. 1. Click the Windows Start button and select the Control Panel option. 2. Click the Performance and Maintenance icon in the Control Panel. 3. Click the System icon in the Performance and Maintenance window. 4. Click the Advanced tab in the System Properties window. 5.
Operating Basics Important information for use Note the following limitations when you write video DVD: 1. Editing digital video ■ Log in with Administrator rights to use WinDVD Creator. ■ Make sure that your computer is running on AC power when using WinDVD Creator. ■ Operate the computer at Full Power. Do not use power-saving features. ■ While you are editing DVD, you can display previews. However, if another application is running, the preview might not display properly.
Operating Basics 2. Before recording the video to DVD ■ When you record to DVD disc, please use only discs recommended by the Drive manufacturer. ■ Do not set the working drive to a slow device like a USB 1.1 hard disk drive or it will fail to write DVD. ■ Do not perform any of the following actions: ■ Operate the computer for any other function, including using a mouse or Touch pad or closing/opening the LCD panel. ■ Bump or cause vibration to the computer.
Operating Basics Media Care This section provides tips on protecting data stored on your CD/DVDs and diskettes. Handles your media with care. The following simple precautions will increase the lifetime of your media and protect the data stored on them: 1. Store your CD/DVDs in the container they came in to protect them and keep them clean. 2. Do not bend the CD/DVD. 3. Do not write on, apply a sticker to, or otherwise mar the surface of the CD/ DVD that contains data. 4.
Operating Basics Using the internal modem This section describes how to make settings and connect the modem. Refer to the computer's online help files for more information. Refer also to the online help files for your modem software. The internal modem does not support the voice functions described in the help files. All data and fax functions are supported. ■ In case of a lightning storm, unplug the modem cable(optional) from the telephone jack. ■ Do not connect the modem to a digital telephone line.
Operating Basics 4. Select a region from the region menu or a telephony location from the submenu. ■ When you click a region it becomes the modem's region selection, and the New Location for telephony will be set automatically. ■ When you select a telephony location, the corresponding region is automatically selected and it becomes the modem's current region setting. Properties menu Click the icon with the secondary mouse button to display the following menu.
Operating Basics Dialing Properties Select this item to display the dialing properties. If you are using the computer in Japan, technical regulations described in the Telecommunications Business Law require that you select Japan region mode. It is illegal to use the modem in Japan with any other selection. Connecting To connect the internal modem cable(optional), follow the steps below. ■ In case of a lightning storm, unplug the modem cable(optional) from the telephone jack.
Operating Basics LAN The computer is equipped with LAN circuits that support Ethernet LAN (10 megabits per second, 10BASE-T) and Fast Ethernet LAN (100 megabits per second, 100BASE-TX). This section describes how to connect/ disconnect to a LAN. Do not install or remove an optional memory module while Wake-up on LAN is enabled. Wake-up on LAN does not work without the AC adaptor. Leave it connected, if you are using this feature.
Operating Basics Wireless LAN The wireless LAN is compatible with other LAN systems that comply with the IEEE 802.11a+g, and 802.11g wireless LAN standards. It supports the following: ■ Automatic Transmit Rate Select mechanism in the transmit range of 54, 11, 5.5, 2 and 1 Mbit/s. (54 Mbps is available only with 802.11a or 802.11g.) ■ Advanced Encryption Standard (AES) data encryption, based on 128bit encryption algorithm. (Revision G, A/G combo type.) Wake-up on LAN does not function on a Wireless LAN.
Operating Basics TV-Out Use the TV-Out jack to connect to a television. Be sure to use a 4 pin type S-video cable. For more details, see Appendix B, Display Modes. TV out Setting up more than one display You can set up your computer to utilize more than one display, effectively spreading a single desktop screen across two monitors. The Display Properties window allows you to adjust more precisely the relative positioning of the two displays when they are configured as an extended desktop.
Operating Basics If an external display will not be connected next time you use your computer, you should cancel any extended desktop or clone display settings before shutting down your computer. Clone display settings are those where more than one device has been selected and is simultaneously applicable. Cleaning the computer To help ensure long, trouble-free operation, keep the computer free of dust and use care with liquids around the computer. ■ Be careful not to spill liquids into the computer.
Satellite P30 Series Chapter 5 The Keyboard The computer's keyboard layouts are compatible with a 101/102-key enhanced keyboard. By pressing some keys in combination, all the 101/ 102-key keyboard functions can be executed on the computer. The number of keys on your keyboard depends on which country/region's keyboard layout your computer is configured with. Keyboards for numerous languages are available.
The Keyboard F1 ... F12 function keys The function keys, not to be confused with Fn, are the 12 keys at the top of your keyboard. These keys are dark gray, but function differently from the other dark gray keys. F1 through F12 are called function keys because they execute programmed functions when pressed. Used in combination with the Fn key, keys marked with icons execute specific functions on the computer. See the section, Soft keys: Fn key combinations, in this chapter.
The Keyboard Press Fn + Enter to simulate Enter on the enhanced keyboard's numeric keypad. Press Fn + Ctrl to simulate the enhanced keyboard's right Ctrl key. Hotkeys Fn + ESC Volume Mute Turns the volume on and off. Fn + F1 Instant Security Enters screen saver mode and blanks the screen. To restore your desktop, press any key or use the TouchPad.
The Keyboard Fn + F11 Numeric Keypad On/Off This hot key enables/ disables the embedded numeric keypad. Numeric lock state is logically enabled. See Chapter 3, Getting Started for more information. Fn + F12 Scroll Lock On/Off Fn + Space Change Resolution Cycles sequentially from the current resolution to 800x600 to 1024x768 and back again to the original resolution. Fn + 1 Fn + 2 .
The Keyboard Keypad overlay Your computer's keyboard does not have an independent numeric keypad, but its numeric keypad overlay functions like one. The keys in the center of the keyboard with white letters make up the numeric keypad overlay. The overlay provides the same functions as the numeric keypad on the 101/102-key enhanced keyboard in figure 5-2. Turning on the overlays The numeric keypad overlay can be used for numeric data input or cursor and page control.
The Keyboard Temporarily using normal keyboard (overlay on) While using the overlay, you can temporarily access the normal keyboard without turning off the overlay: 1. Hold down Fn and press any other key. All keys will operate as if the overlay were off. 2. Type upper-case characters by holding down Fn + Shift and pressing a character key. 3. Release Fn to continue using the overlay.
Satellite P30 Series Chapter 6 Power and Power-Up Modes The computer's power resources include the AC adaptor and internal batteries. This chapter gives details on making the most effective use of these resources including charging and changing batteries, tips for saving battery power, and power up modes.
Power and Power-Up Modes AC adaptor not connected Power on Power off (no operation) Battery charge is above low battery trigger point • Operates • LED: Battery off DC IN off — Battery charge is below low battery trigger point — • Operates • Alarm sounds (depending on the TOSHIBA Power Saver utility setting) • LED: Battery flashes amber DC IN off Battery charge exhausted Computer goes into Hibernation or shuts down — No battery installed • No operation — (depending on the TOSHIBA Power Saver u
Power and Power-Up Modes DC IN indicator Check the DC IN indicator to determine the power status with the AC adaptor connected: Green Indicates the AC adaptor is connected and supplying proper power to the computer. No light Indicates the AC adaptor is not connected. Power indicator Check the Power indicator to determine the power status with the AC adaptor connected: Blue/Green The power button will shinning blue while power is being supplied to the computer and the computer is turned on.
Power and Power-Up Modes Battery pack When the AC adaptor is not connected, the computer's main power source is a removable lithium ion battery pack, also referred to in this manual as the battery. You can purchase additional battery packs for extended use of the computer away from an AC power source. The battery is a disposable item. When its operation becomes short even when fully charged, replace it with a new one.
Power and Power-Up Modes Care and use of the battery pack The battery pack is a vital component of portable computing. Taking proper care of it will help ensure longer operating time on battery power as well as a longer life for your battery pack. Follow the instructions in this section carefully to ensure safe operation and maximum performance. Safety precautions Mishandling of batteries can cause death, serious injury or property damage.
Power and Power-Up Modes 8. Never expose the battery pack to abnormal shock, vibration or pressure. The battery pack's internal protective device will fail, causing it to overheat, explode, ignite or leak caustic liquids possibly resulting in death or serious injury. 9. Never let a battery pack become wet. A wet battery pack will overheat, ignite or rupture possibly resulting in death or serious injury. Warning 1.
Power and Power-Up Modes 6. Be sure to monitor the remaining battery power. If the battery pack and real time clock battery discharge completely, Standby and Suspend will not function and data in memory will be lost. Also, the computer might register an incorrect time and date. In this case, connect the AC adaptor to recharge the batteries. 7. Never install or remove the battery pack without first turning off the power and disconnecting the AC adaptor.
Power and Power-Up Modes Time The following table shows the time required to fully charge a discharged battery. Charging time (hours) Battery type Power on Power off Battery pack about 12 or longer about 4 or longer RTC battery about 24 about 24 with AC or Battery pack The charging time when the computer is on is affected by ambient temperature, the temperature of the computer and how you use the computer.
Power and Power-Up Modes In such case, follow the steps below. 1. Fully discharge the battery by leaving it in the computer with the power on until the power automatically shuts off. 2. Plug in the AC adaptor. 3. Charge the battery until the Battery indicator glows green. Repeat these steps two or three times until the battery recovers normal capacity. Leaving the AC adaptor connected will shorten battery life.
Power and Power-Up Modes Maximizing battery operating time A battery's usefulness depends on how long it can supply power on a single charge. How long the charge lasts in a battery depends on: ■ How you configure the computer (for example, whether you enable battery power saving options). The computer provides a battery save mode to conserve battery power.
Power and Power-Up Modes Replacing the battery pack When the battery pack reaches the end of its operating life you will need to install a new one. If the Battery indicator flashes amber shortly after the battery has been fully recharged, the battery pack needs to be replaced. You might also replace a discharged battery pack with a charged spare when you are operating your computer away from an AC power source. This section explains how to remove and install the battery pack.
Power and Power-Up Modes Installing the battery pack To install a battery pack, follow the steps below. The battery pack is a lithium ion battery, which can explode if not properly replaced, used, handled or disposed of. Dispose of the battery as required by local ordinances or regulations. Use only batteries recommended by TOSHIBA as replacements. 1. Turn the computer's power off. 2. Disconnect all cables connected to the computer. 3.
Power and Power-Up Modes Panel power off/on You can set up your computer so that power turns off automatically when you close the display panel. When you open the panel, power turns on in Standby or Hibernation mode but not in boot mode. If the panel power off function is enabled and you use Shut down Windows, do not close the display until the shut down function is completed.
Satellite P30 Series Chapter 7 Optional Devices Optional devices can expand the computer's capabilities and its versatility.
Optional Devices PC cards The computer is equipped with a PC card expansion slot that can accommodate one 5 mm Type II card. Any PC card that meets industry standards (manufactured by TOSHIBA or other vendor) can be installed. The slots support 16-bit PC cards, including PC card 16's multifunction card and CardBus PC cards. CardBus supports the new standard of 32-bit PC cards. The bus provides superior performance for the greater demands of multimedia data transmission.
Optional Devices Removing a PC card 1. 2. 3. 4. 5. Click the Safety Remove Hardware icon on the Task Bar. Click the PC card you want to remove. Press the eject button of the PC card to extend it. Press the extended eject button to pop the card out slightly. Grasp the PC card and remove it.
Optional Devices SD/MMC/SM/MS/MS Pro/xD Memory Cards The computer is equipped with a Multiple Digital Media Card Slot that can accommodate SD/MMC/SM/MS/MS Pro/xD memory cards. These memory cards let you easily transfer data from devices, such as digital cameras and Personal Digital Assistants, that use flash-memory.
Optional Devices Installing an Memory card To install a memory card, follow the steps below. 1. Insert the memory card. 2. Press gently to ensure a firm connection. Inserting an memory card Be sure the memory card is oriented properly before you insert it. If Windows fails to read the memory card, remove it then reinsert it. ■ Two kinds of cards will not work at the same time. Insert only one card when using Multiple Digital Media Card Slot. ■ 5V SmartMedia card is not supported.
Optional Devices Removing a Memory card To remove a memory card, follow the steps below. 1. Click the Safety Remove Hardware icon on the Task Bar. 2. Stop a memory card device which you want to remove. 3. Grasp the card and remove it. Removing a memory card ■ Make sure the memory card indicator is out before you remove the card or turn off the computer's power. If you remove the card or turn off the power while the computer is accessing the card you may lose data or damage the card.
Optional Devices Memory card care Set the write-protect switch to the lock position, if you do not want to record data. 1. Do not write to a memory card if the battery power is low. Low power could affect writing accuracy. 2. Do not remove a memory card while read/write is in progress. 3. The memory card is designed so that it can be inserted only one way. Do not try to force the card into the slot. 4. Do not leave a memory card partially inserted in the slot.
Optional Devices Installing memory module If you use the computer for a long time, the memory modules will become hot. In this case, let the memory modules cool to room temperature before you replace them. Follow these steps to install a memory module: 1. Set the computer to boot mode and turn off the power. Do not try to install a memory module under the following conditions. You can damage the computer and the module. ■ The computer is turned on. ■ The computer was shut down using the Stand by mode.
Optional Devices 7. Push the module down so it lies flat. Latches on either side will click into place to secure the module. 1 2 Installing a module 8. Seat the cover and secure it with two screws. 9. Replace the battery pack as described in Chapter 6, Power and PowerUp Modes. 10. Turn the power on and make sure the added memory is recognized. Removing memory module If you use the computer for a long time, the memory modules will become hot.
Optional Devices 5. Grasp the module and pull it out. Do not touch the connectors on the memory module or on the computer. Debris on the connectors may cause memory access problems. Removing the memory module 6. Seat the cover and secure its screws. 7. Replace the battery. Additional battery pack You can increase the portability of the computer with additional battery packs. If you're away from an AC power source and your battery runs low, you can replace it with a freshly charged battery.
Optional Devices External monitor An external analog monitor can be connected to the external monitor port on the computer. To connect a monitor, follow the steps below. 1. Turn the computer off. 2. Connect the monitor to the external monitor port. 3. Turn the monitor's power on. 4. Turn the computer on. When you turn on the power, the computer automatically recognizes the monitor. To change the display settings, press Fn + F5.
Optional Devices Television A television can be connected to the video out port on the computer. To connect a television, follow the steps below. 1. Turn the computer off. 2. Use a video cable (not supplied) to connect the television to the video out port. 3. Turn the television on. 4. Turn the computer on. You can use the hotkeys Fn + F5 or use the TV-Out button to change the display device. Refer to Chapter 5, The Keyboard.
Optional Devices 4. Click the Advanced button and choose Displays 5. Click the TV button to open the TV Properties dialog box. 6.
Optional Devices i.LINK (IEEE1394) i.LINK (IEEE1394) is used for high-speed data transfer for a range of compatible devices such as: ■ Digital video cameras ■ Hard disk drives ■ MO drives ■ Optical media drives i.LINK uses a four-pin connector, which does not carry electric current. External devices will need their own power supply. Precautions ■ Make a back-up of your data before transferring it to the computer. There is a possibility that the original data will be damaged.
Optional Devices Security lock A security lock enables you to anchor your computer to a desk or other heavy object to help prevent unauthorized removal of the computer. Attach one end of a cable to the desk and the other end to the security lock slot on the right side of the computer.
Satellite P30 Series Chapter 8 Troubleshooting TOSHIBA designed the computer for durability. However, should problems occur, following the procedures in this chapter can help to determine the cause. All readers should become familiar with this chapter. Knowing what might go wrong can help prevent problems from occurring. Problem solving process Resolving problems will be much easier if you observe the following guidelines: ■ Stop immediately when you recognize a problem exists.
Troubleshooting Preliminary checklist Consider the simplest solution first. The items in this checklist are easy to fix and yet can cause what appears to be a serious problem. ■ Make sure you turn on all peripheral devices before you turn on the computer. This includes your printer and any other external device you are using. ■ Before you attach an external device, turn the computer off. When you turn the computer back on it recognizes the new device.
Troubleshooting Software The problems may be caused by your software or diskette. If you cannot load a software package, the media may be damaged or the program might be corrupted. Try loading another copy of the software. If an error message appears while you are using a software package, check the software documentation. These documents usually include a problem solving section or a summary of error messages. Next, check any error messages in the OS documentation.
Troubleshooting System start-up When the computer does not start properly, check the following items: ■ Self Test ■ Power Sources ■ Power-on Password Self test When the computer starts up, the self test will be run automatically, and the following will be displayed: This message remains on the screen for a few seconds. If the self test is successful, the computer tries to load the operating system. Depending on how the Boot Priority is set in the computer’s BIOS.
Troubleshooting Power When the computer is not plugged into an AC outlet, the battery pack is the primary power source. However, your computer has a number of other power resources, including intelligent power supply, Real Time Clock battery. These resources are interrelated and any one could affect apparent power problems. This section provides check lists for AC power and the battery. If you cannot resolve a problem after following them, the cause could lie with another power resource.
Troubleshooting Battery If you suspect a problem with the battery, check the DC IN indicator as well as the indicators for the battery. For information on indicators and battery operation see Chapter 6, Power and Power-Up Modes. User’s Manual Problem Procedure Battery doesn't power the computer. The battery may be discharged. Connect the AC power cord to charge the battery. Battery doesn't charge when the AC power cord is attached. (Battery indicator does not glow amber.
Troubleshooting Keyboard Keyboard problems can be caused by your setup configuration. For more information refer to Chapter 5, The Keyboard. Problem Procedure Some letter keys produce numbers. Check that the numeric keypad overlay is not selected. Press Fn + F10 and try typing again. Output to screen is garbled. Make sure the software you are using is not remapping the keyboard. Remapping involves reassigning the meaning of each key. See your software's documentation.
Troubleshooting Hard disk drive Problem Procedure Computer does not boot from hard drive. Insert a system diskette and reboot. There may be a problem with your operating system files. Refer to your OS documentation. Slow performance Your files may be fragmented. Run SCANDISK and defragmenter to check the condition of your files and disk. Refer to your OS documentation or online HELP for information on running SCANDISK and the defragmenter. Contact your dealer if the problems continue.
Troubleshooting Problem Procedure The software or hardware configuration may be Some CD/DVDs run correctly, but others do causing a problem. Make sure the hardware configuration matches your software's needs. not. Check the CD/DVD's documentation. Check the type of CD/DVD you are using.
Troubleshooting DVD±R/±RW drive (DVD Dual Drive) For more information, refer to Chapter 4, Operating Basics. Problem Procedure Some CD run correctly, The software or hardware configuration may be but others do not. causing a problem. Make sure the hardware configuration matches your software's needs. Check the CD/DVD's documentation. Check the type of CD/DVD you are using.
Troubleshooting Problem Procedure Cannot write correctly If you have trouble writing, make sure you are observing the following precautions: ■ Use only media recommended by TOSHIBA. ■ Do not use the mouse or keyboard during writing. ■ Use only the software supplied with the computer for recording. ■ Do not run or start other software during writing. ■ Do not jar the computer during writing. ■ Do not connect/ disconnect external devices or install/remove internal cards during writing.
Troubleshooting Problem Procedure Some CD run correctly, The software or hardware configuration may be but others do not. causing a problem. Make sure the hardware configuration matches your software's needs. Check the CD/DVD's documentation. Check the type of CD/DVD you are using.
Troubleshooting Diskette drive For more information on the diskette drive, refer to Chapter 2, The Grand Tour. For information on diskette care refer to Chapter 4, Operating Basics. Problem Procedure The software or hardware configuration may be Some programs run correctly, but others do causing a problem. Make sure the hardware configuration match's your software's needs. not. You cannot access the diskette drive probably causing the. Try another disk.
Troubleshooting Memory cards Refer also to Chapter 7, Optional Devices. Problem Procedure Memory card error occurs. Reseat the memory card to make sure it is firmly connected. Check the card's documentation. If problems persist, contact your dealer. Pointing device If you are using a USB mouse, also refer to the USB section in this chapter and to your mouse documentation. Touch pad User’s Manual Problem Procedure On-screen pointer does not respond to Pad operation. The system might be busy.
Troubleshooting USB mouse Problem Procedure On-screen pointer does not respond to Pad operation. The system might be busy. If the pointer is shaped as an hourglass, wait for it to resume its normal shape and try again to move it. Make sure the mouse is properly connected to the USB port. Double-tapping does not work. Try changing the double-click speed setting in the mouse control utility. 1. Open the Control Panel, select the Mouse icon and press Enter. 2. Click the Buttons tab. 3.
Troubleshooting Standby/Hibernation Problem Procedure The system will not enter Standby/ Hibernation. Is Windows Media™ Player open? The system might not enter Standby/Hibernation, if Windows Media Player is either playing a selection or finished playing a selection. Close Windows Media Player before you select Standby/ Hibernation. If problems persist, contact your dealer.
Troubleshooting Memory expansion Refer also to Chapter 7, Optional Devices, for information on installing memory modules. Problem Procedure The computer hangs up and issues beep sounds. (A long leep, three short beeps, three short beeps, and then a long beep.) Make sure the memory module installed in the expansion slot is compatible with the computer. If an incompatible module has been installed, follow the steps below. 1. Turn off the power. 2. Disconnect the AC adaptor and all periph-eral devices. 3.
Troubleshooting Problem Procedure Character display becomes garbled during a communication. In data transmission, make sure the parity bit and stop bit settings correspond with those of the remote computer. Check the flow control and communication protocol. You cannot receive an incoming call. Check the "rings before auto answer" setting in your communications application. If problems persist, contact your dealer. Problem Procedure Cannot access LAN LAN jack and the Wake up on LAN does not work.
Troubleshooting Monitor Refer also to Chapter 7, Optional Devices, and to your monitor’s documentation. Problem Procedure Monitor does not turn on. Make sure that the external monitor's power switch is on. Confirm that the external monitor's power cable is plugged into a working power outlet. No display Try adjusting the contrast and brightness controls on the external monitor. Press hotkeys Fn + F5 to change the display priority and make sure it is not set for the internal display.
Troubleshooting TOSHIBA support If you require any additional help using your computer or if you are having problems operating the computer, you may need to contact TOSHIBA for additional technical assistance. Before you call Some problems you experience may be related to software or the operating system, it is important to investigate other sources of assistance first. Before contacting TOSHIBA, try the following: ■ Review troubleshooting sections in the documentation for software and peripheral devices.
Satellite P30 Series Appendix A Specifications This appendix summarizes the computer's technical specifications. Dimensions 420mm x 293mm x 39.9mm (Front)/47mm (Rear) Weight 4.3kg/9.49lbs (Actual weight may vary depending on configuration.
Specifications Built-in Modem Network control unit (NCU) Type of NCU AA Type of line Telephone line (analog only) Type of dialing Pulse Tone Control command AT commands EIA-578 commands Monitor function Computer's speaker Communication specifications Communication System Data: Fax: Communication Protocol Data: ITU-T-Rec (Former CCITT) Bell Fax: ITU-T-Rec (Former CCITT) User’s Manual Full duplex Half duplex V.21/V.22/V.22bis/V.32/ V.32bis/V.34/V.90/ V.92(only for USA and Canada) 103/212A V.
Satellite P30 Series Appendix B Display Modes This appendix contains a table listing all the display modes currently supported by the ATI Mobility Radeon graphics controller.
Display Modes Displaying movies on a TV or CRT This section describes how to set up your system to display movies simultaneously on your computer's LCD and on an external TV or CRT monitor. Follow the steps below. 1. Open the Control Panel and click Appearance and Themes. 2. Click Display. 3. Select the Settings tab and click Advanced. 4. Click the Displays tab. 5. Select the external display device you wish to use. It must be connected to the computer in order to be selected from the menu here.
Display Modes 6. In the resulting properties box, if any additional options are available for your particular device, set then to your liking.
Display Modes 7. Finally, click the ATI Overlay tab to adjust the video overlay properties.
Satellite P30 Series Appendix C Power Cable Connectors The Satellite computer features a universal power supply you can use worldwide. This appendix shows the configuration of typical AC power cord plugs and sockets in various parts of the world. The following illustrations show the plug shapes for the U.S.A.
Satellite P30 Series Appendix D If your computer is stolen Always take care of your computer and try to prevent it from being stolen. You are the owner of a valuable technical device, which may be highly attractive to thieves, so please do not leave it unattended in a public place. To further help protect against theft, security cables can be bought for use with your notebook when it is being used at home or in the office.
If your computer is stolen TOSHIBA Theft Registration Send to: Fax number: TOSHIBA Europe GmbH Technical Service and Support Leibnizstr. 2 93055 Regensburg Germany +49 (0) 941 7807 921 Country stolen: Machine type: (e.g. Satellite A50) Model number: (e.g. PSA50 YXT) Serial number: (e.g.
Satellite P30 Series Glossary The terms in this glossary cover topics related to this manual. Alternate naming is included for reference.
Glossary RAM: random access memory ROM: read only memory RTC: real time clock SCSI: small computer system interface TFT: thin-film transistor USB: Universal Serial Bus VESA: Video Electronic Standards Association VGA: video graphics array XGA: extended graphics array A adaptor: A device that provides an interface between two dissimilar electronic devices. For example, the AC adaptor modifies the power from a wall outlet for use by the computer.
Glossary C cache memory: High speed memory which stores data that increases processor speed and data transfer rate. When the CPU reads data from main memory, it stores a copy of this data in cache memory. The next time the CPU needs that same data, it looks for it in the cache memory rather than the main memory, which saves time. The computer has two cache levels. Level one is incorporated into the processor and level two resides in external memory.
Glossary CRT: Cathode Ray Tube. A vacuum tube in which beams projected on a fluorescent screen-producing luminous spots. An example is the television set. cursor: A small, blinking rectangle or line that indicates the current position on the display screen. D DC: Direct Current. Electric current that flows in one direction. This type of power is usually supplied by batteries. default: The parameter value automatically selected by the system when you or the program do not provide instructions.
Glossary floppy disk drive (FDD): An electromechanical device that reads and writes to floppy disks. folder: An icon in Windows used to store documents or other folders. format: The process of readying a blank disk for its first use. Formatting establishes the structure of the disk that the operating system expects before it writes files or programs onto the disk. function keys: The keys labeled F1 through F12 that tell the computer to perform certain functions.
Glossary IrDA 1.1: An industry standard that enables cableless infrared serial data transfer at speeds of up to 4 Mbps. J jumper: A small clip or wire that allows you to change the hardware characteristics by electrically connecting two points of a circuit. K K: Taken from the Greek word kilo, meaning 1000; often used as equivalent to 1024, or 2 raised to the 10th power. See also byte and kilobyte. KB: See kilobyte.
Glossary N numeric keypad overlay: A feature that allows you to use certain keys on the keyboard to perform numeric entry, or to control cursor and page movement. O operating system: A group of programs that controls the basic operation of a computer. Operating system functions include interpreting programs, creating data files, and controlling the transmission and receipt (input/output) of data to and from memory and peripheral devices. output: The results of a computer operation.
Glossary ROM: Read Only Memory: A nonvolatile memory chip manufactured to contain information that controls the computer’s basic operation. You cannot access or change information stored in ROM. S SCSI: Small Computer System Interface is an industry standard interface for connection of a variety of peripheral devices. soft key: Key combinations that emulate keys on the IBM keyboard, change some configuration options, stop program execution, and access the numeric keypad overlay.
