User's Manual P50-B/P50t-B
Table of Contents Chapter 1 TOSHIBA Legal, Regulatory and Safety Copyright, Disclaimer and Trademarks .............................................. 1-1 Regulatory Information ......................................................................... 1-2 Video Standard Notice .......................................................................... 1-7 OpenSSL Toolkit License Issues ......................................................... 1-8 FreeType License Issues .......................................
Battery .................................................................................................. 4-24 LAN ....................................................................................................... 4-27 Additional memory module ................................................................ 4-29 Memory media ..................................................................................... 4-33 External Display .......................................................................
Chapter 1 TOSHIBA Legal, Regulatory and Safety This chapter states the Legal, regulatory and safety information applicable to TOSHIBA computers. Copyright, Disclaimer and Trademarks Copyright © 2014 by TOSHIBA Corporation. All rights reserved. Under the copyright laws, this manual cannot be reproduced in any form without the prior written permission of TOSHIBA. No patent liability is assumed, with respect to the use of the information contained herein.
The Bluetooth® word mark and logos are registered trademarks owned by Bluetooth SIG, Inc. and any use of such marks by Toshiba Corporation and its affiliates is under license. The terms HDMI and HDMI High-Definition Multimedia Interface, and the HDMI Logo are trademarks or registered trademarks of HDMI Licensing LLC in the United States and other countries. sMedio, and sMedio TrueLink+ are trademarks or registered trademarks of sMedio, Inc.
Only peripherals complying with the FCC class B limits may be attached to this equipment. Operation with non-compliant peripherals or peripherals not recommended by TOSHIBA is likely to result in interference to radio and TV reception. Shielded cables must be used between the external devices and the computer’s Universal Serial Bus (USB 3.0) ports, HDMI port and microphone combo jack.
Ecodesign Directive 2009/125/EC (ErP) and the related implementing measures. This product and the original options are designed to observe the related EMC (Electromagnetic Compatibility) and safety standards. However, TOSHIBA cannot guarantee that this product still observes these EMC standards if options or cables not produced by TOSHIBA are connected or implemented.
Canadian regulatory information (Canada only) This digital apparatus does not exceed the Class B limits for radio noise emissions from digital apparatus as set out in the Radio Interference Regulation of the Canadian Department of Communications. Note that Canadian Department of Communications (DOC) regulations provide, that changes or modifications not expressly approved by TOSHIBA Corporation could void your authority to operate this equipment.
Disposal of batteries and/or accumulators The crossed out wheeled dust bin symbol indicates that batteries and/or accumulators must be collected and disposed of separately from household waste. If the battery or accumulator contains more than the specified values of lead (Pb), mercury (Hg), and/or cadmium (Cd) defined in the European Battery Directive, then the chemical symbols for lead (Pb), mercury (Hg) and/or cadmium (Cd) will appear below the crossed out wheeled dust bin symbol.
Following information is only for Turkey: Disposal of products: The crossed wheelie bin symbol means that this product should not be collected and disposed with other household wastes. When product become waste at the end-of-life, to protect environment and human health, it should be given to nearest collection recycling or disposal center. For more information about collection and recycling programs in your country please contact your local authority or the retailer where the product was purchased.
NONCOMMERCIAL ACTIVITY AND/OR WAS OBTAINED FROM A VIDEO PROVIDER LICENSED BY MPEG LA TO PROVIDE SUCH VIDEO. NO LICENSE IS GRANTED OR SHALL BE IMPLIED FOR ANY OTHER USE. ADDITIONAL INFORMATION INCLUDING THAT RELATING TO PROMOTIONAL, INTERNAL AND COMMERCIAL USES AND LICENSING MAY BE OBTAINED FROM MPEG LA, L.L.C. SEE HTTP://WWW.MPEGLA.COM OpenSSL Toolkit License Issues LICENSE ISSUES ============== The OpenSSL toolkit stays under a dual license, i.e.
6. Redistributions of any form whatsoever must retain the following acknowledgment: "This product includes software developed by the OpenSSL Project for use in the OpenSSL Toolkit" ( http://www.openssl.org/ ) THIS SOFTWARE IS PROVIDED BY THE OpenSSL PROJECT ``AS IS'' AND ANY EXPRESSED OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED.
Redistribution and use in source and binary forms, with or without modification, are permitted provided that the following conditions are met: 1. 2. 3. Redistributions of source code must retain the copyright notice, this list of conditions and the following disclaimer. Redistributions in binary form must reproduce the above copyright notice, this list of conditions and the following disclaimer in the documentation and/or other materials provided with the distribution.
Introduction ============ The FreeType Project is distributed in several archive packages; some of them may contain, in addition to the FreeType font engine, various tools and contributions which rely on, or relate to, the FreeType Project. This license applies to all files found in such packages, and which do not fall under their own explicit license. The license affects thus the FreeType font engine, the test programs, documentation and makefiles, at the very least.
`You' refers to the licensee, or person using the project, where `using' is a generic term including compiling the project's source code as well as linking it to form a `program' or `executable'. This program is referred to as `a program using the FreeType engine'. This license applies to all files distributed in the original FreeType Project, including all source code, binaries and documentation, unless otherwise stated in the file in its original, unmodified form as distributed in the original archive.
Neither the FreeType authors and contributors nor you shall use the name of the other for commercial, advertising, or promotional purposes without specific prior written permission. We suggest, but do not require, that you use one or more of the following phrases to refer to this software in your documentation or advertising materials: `FreeType Project', `FreeType Engine', `FreeType library', or `FreeType Distribution'. As you have not signed this license, you are not required to accept it.
ENERGY STAR® Program Your Computer model may be ENERGY STAR® compliant. If the model you purchased is compliant, it is labeled with the ENERGY STAR logo on the computer and the following information applies. TOSHIBA is a partner in the ENERGY STAR Program and has designed this computer to meet the latest ENERGY STAR guidelines for energy efficiency.
The drive model employs a laser system. To ensure proper use of this product, please read this instruction manual carefully and retain for future reference. Should the unit ever require maintenance, contact an authorized service location. Use of controls, adjustments or the performance of procedures other than those specified may result in hazardous radiation exposure. To prevent direct exposure to the laser beam, do not try to open the enclosure. Location of the Required Label (Sample shown below.
Provide adequate ventilation Always make sure your computer and AC adaptor have adequate ventilation and are protected from overheating when the power is turned on or when an AC adaptor is connected to a power outlet (even if your computer is in Sleep Mode). In this condition, observe the following: Never cover your computer or AC adaptor with any object. Never place your computer or AC adaptor near a heat source, such as an electric blanket or heater.
Heat injury Avoid prolonged physical contact with the computer. If the computer is used for long periods, its surface can become very warm. While the temperature will not feel hot to the touch, if you maintain physical contact with the computer for a long time, for example if you rest the computer on your lap or if you keep your hands on the palm rest, your skin might suffer a low-heat injury.
Turn off (shut down) the computer. Disconnect the AC adaptor and all peripherals before moving the computer. Close the display panel. Do not pick up the computer by its display panel. Before carrying your computer, shut it down, disconnect the AC adaptor and allow it to cool down - a failure to follow this instruction may result in minor heat injury.
Chapter 2 Getting Started This chapter provides an equipment checklist, and basic information to start using your computer. Some of the features described in this manual may not function properly if you use an operating system that was not pre-installed by TOSHIBA. Equipment checklist Carefully unpack your computer, taking care to save the box and packaging materials for future use.
Right-click Click the right Touch Pad control button once. Right-click the mouse once. Press and hold on the touch screen (only for touch screen models). Double-click Tap the Touch Pad or click the left Touch Pad control button twice. Left-click the mouse twice. Tap the touch screen twice (only for touch screen models).
chance of developing a painful or disabling injury to your hand, arms, shoulders or neck. This section provides basic information to start using your computer. It covers the following topics: Connecting the AC adaptor Opening the display Turning on the power Initial setup Use a virus-check program and make sure it is updated regularly. Never format storage media without checking its content - formatting destroys all stored data.
Always use or purchase power cables that comply with the legal voltage and frequency specifications and requirements in the country of use. Failure to do so could result in a fire or electric shock, possibly resulting in serious injury. The supplied power cord conforms to safety rules and regulations in the region the computer is bought and should not be used outside this region. For use in other regions, please buy power cords that conform to safety rules and regulations in the particular region.
2. Connect the AC adaptor’s DC output plug to the DC IN 19V jack on your computer. Figure 2-3 Connecting the DC output plug to the computer 1 2 1. DC IN 19V jack 3. 2. DC output plug Plug the power cord into a live wall outlet - the DC IN/Battery indicator should glow. Opening the display The display panel can be opened to a wide range of angles for optimal viewing.
When opening or closing the display panel, place one hand on the palm rest to hold the computer in place and use the other hand to slowly open or close the display panel (Do not use excessive force when opening or closing the display panel). Turning on the power This section describes how to turn on the power - the Power indicator will then indicate the status. Please refer to the Power Condition Descriptions section for more information.
Getting to know Windows For detailed information on what is new and how to operate Windows, please refer to the Windows Help and Support. Start screen The Start screen is the launching pad for everything you can do in the Windows operating system, providing new and easy ways to access everything from your favorite apps and Web sites to your contacts and other important information. From the Start screen, you can just start typing to search for what you want.
Devices This charm allows you to manage your hardware. Settings This charm allows you to access your computer’s settings (volume, brightness, connecting to the internet, and more). Tiles Tiles can be accessed and launched from the Start screen. Typical Start screen tiles are the Desktop tile and Mail tile, as well as tiles representing all other applications downloaded to your system.
2. Make sure all disk/disc activity has stopped before removing the disk/ disc. If you turn off the power while a disk (disc) is being accessed, you may lose data or damage the disk. Never turn off the power while an application is running. Doing so could cause loss of data. Never turn off the power, disconnect an external storage device or remove storage media during data read/write. Doing so can cause data loss. 3. 4. Click the power icon ( ) on the Start screen and then select Shut down.
Before entering Sleep Mode, be sure to save your data. Do not switch to Sleep Mode while transferring data to external media, such as USB devices, memory media or other external memory devices. Data will be lost. Do not install or remove a memory module while the computer is in Sleep Mode. The computer or the memory module could be damaged.
When the computer is in Sleep Mode, the Power indicator will blink white. If you are operating the computer on battery power, you can lengthen the overall operating time by turning it off into Hibernation Mode Sleep Mode will consume more power while the computer is off. Sleep Mode limitations Sleep Mode will not function under the following conditions: Power is turned back on immediately after shutting down. Memory circuits are exposed to static electricity or electrical noise.
Starting Hibernation Mode To enter Hibernation Mode, click the power icon ( and then select Hibernate. ) on the Start screen In order to show Hibernate in Power menu, you need to setup according to the following steps: 1. Click Desktop Assist -> Control Panel -> System and Security -> Power Options on the desktop. 2. Click Choose what the power button does or Choose what closing the lid does. 3. Click Change settings that are currently unavailable. 4. Select the Hibernate check box from Shutdown settings.
Chapter 3 The Grand Tour This chapter identifies the various components of the computer - it is recommended that you become familiar with each before you operate the computer. Legal Footnote (Non-applicable Icons) For more information regarding Non-applicable Icons, please refer to the Legal Footnotes section. Please handle your computer carefully to avoid scratching or damaging the surface.
Power indicator The Power indicator glows white when the computer is turned on. However, if you turn the computer off into Sleep Mode, this indicator will blink white. Wireless communication indicator The Wireless communication indicator glows amber when the Bluetooth or Wireless LAN functions are turned on. Only some models are equipped with Bluetooth and Wireless LAN functions. Memory media slot This slot lets you insert an SD™/SDHC™/ SDXC™ memory card, miniSD™/microSD™ Card and MultiMediaCard™.
LAN jack This jack lets you connect to a LAN. The adaptor has built-in support for Ethernet LAN (10 megabits per second, 10BASE-T), or Fast Ethernet LAN (100 megabits per second, 100BASE-TX). Some models are equipped with a Gigabit Ethernet LAN (1000 megabits per second, 1000BASE-T). Refer to Operating Basics, for details. Do not connect any cable other than a LAN cable to the LAN jack. It could cause damage or malfunction. Universal Serial Bus (USB 3.
Figure 3-3 The right side of the computer 1 2 3 4 5 1. Headphone jack 2. Microphone jack 3. Universal Serial Bus (USB 3.0) port 4. Universal Serial Bus (USB 3.0) port 6 7 5. HDMI out port 6. Cooling vents 7. Security lock slot Headphone jack A 3.5 mm mini headphone jack enables connection of stereo headphones. Microphone jack A 3.5 mm mini microphone jack enables connection of a mini jack for monaural microphone input. The jack with the icon ( ) has Sleep and Music function.
Underside The following figures show the underside of the computer. You should ensure that the display is closed before the computer is turned over to avoid causing any damage. Figure 3-5 The underside of the computer 1 2 3 1. Cooling vents 3. Force shut down hole Cooling vents 2. Memory module slot The cooling vents help the processor to avoid overheating. Do not block the cooling vents. Keep foreign metal objects, such as screws, staples and paper clips, out of the cooling vents.
Figure 3-6 The front of the computer with the display panel open 1 2 3 4 5 6 7 7 8 9 8 10 11 12 Figure 3-7 Top side of the touch screen model 2 1 3 4 5 1. Microphone 2. Web Camera LED 3. Web Camera 4. Microphone* 5. Wireless communication antennas (not shown) 6. Display screen 7. Stereo speakers 8. Display hinges 9. Power button 10. Keyboard 11. Touch Pad 12. Touch Pad control buttons * Provided with some models.
Do not touch or press strongly on the web camera lens. Doing so may reduce image quality. Use an eyeglass cleaner (cleaner cloth) or other soft cloth to clean the lens if it becomes dirty. Wireless communication antennas Depending on the configuration of your computer, one or all of the antennas listed below are built-in: Wireless LAN Wireless LAN/Bluetooth Legal Footnote (Wireless LAN) For more information regarding Wireless LAN, please refer to the Legal Footnotes section. Display screen 39.6cm (15.
Keyboard Your computer’s keyboard contains character keys, control keys, function keys, and special Windows keys, providing all the functionality of a full-size keyboard. Refer to the The Keyboard section for details. Touch Pad The Touch Pad located in the palm rest is used to control the movement of the on-screen pointer. To use the Touch Pad, simply touch and move your fingertip across it in the direction you want the on-screen pointer to go.
CPU The processor type varies depending on model. To check which type of processor is included in your model, open the TOSHIBA PC Health Monitor utility by clicking Desktop Assist -> Support & Recovery -> PC Health Monitor on the desktop, and then click PC Information. Legal Footnote (CPU) For more information regarding CPU, please refer to the Legal Footnotes section. Hard Disk Drive or Solid State Drive The capacity of the hard disk drive varies depending on the model.
Video RAM The memory in a computer's graphics adaptor, used to store the image displayed on a bitmap display. The amount of Video RAM available is dependent on the computer's system memory. Click Desktop Assist -> Control Panel -> Appearance and Personalization -> Display -> Adjust resolution on the desktop. The amount of Video RAM can be verified by clicking the Advanced settings button in the Screen Resolution window.
1. 2. 3. Click Power and select On battery. Click Off under Display Power Saving Technology. Click Apply. If you want to enable this feature, under the conditions mentioned above, click On under Display Power Saving Technology. In Intel® Graphics and Media Control Panel: 1. 2. 3. 4. Click Power. Select On battery from the drop-down menu in Power Source. Clear the Display Power Saving Technology check box. Click OK.
Power on Power off (no operation) AC adaptor not connected Remaining battery capacity is above low battery trigger point • Operates Remaining battery capacity is below low battery trigger point • Operates Remaining battery capacity is exhausted Computer shuts down • LED: off • LED: flashes amber DC IN/Battery indicator Check the DC IN/Battery indicator to determine the status of the battery pack and the power status with the AC adaptor connected.
User's Manual Flashing white Indicates that the computer is in Sleep Mode and that there is sufficient power available (AC adaptor or battery) to maintain this condition. No light Under any other conditions, the indicator does not light.
Chapter 4 Operating Basics This chapter describes the basic operations of your computer, and highlights the precautions that should be taken when using it. Using the Touch Screen Some models are equipped with a touch screen. You can use your finger to manipulate icons, buttons, menu items, the onscreen keyboard, and other items on the touch screen. User's Manual Tap Simply tap your finger once on the touch screen to activate an item, such as an app.
Swipe Quickly move your finger in from the edge of the screen, without pausing when you first touch it. Swipe from the left edge: shows your recently opened apps, and so on. Swipe from the right edge: opens or closes the charms (Search, Share, Start, Devices, Settings). Swipe from the top edge: opens or closes the app command bar. For details and more advanced touch screen gestures to interact with Windows operating system, please refer to Help and Support.
Swipe Quickly move your finger in from the edge of the Touch Pad, without pausing when you first touch it. Swipe from the left edge: shows your recently opened apps. Swipe from the right edge: opens or closes the charms (Search, Share, Start, Devices, Settings). Swipe from the top edge: opens or closes the app command bar. Some of the Touch Pad operations described in this section are only supported in certain applications.
CAPS LOCK This indicator glows green when letter keys are locked into their uppercase format. NUM LOCK When the NUM LOCK indicator glows, you can use the number keys on the keyboard for number entry. Function Key The function keys (F1 ~ F12) are the twelve keys at the top of your keyboard. You can configure the function keys’ mode as "Special function mode" or "Standard F1-F12 mode" by clicking Desktop Assist -> Tools & Utilities > System Settings -> Keyboard on the desktop.
Special function mode Standard F1F12 mode Function FN + 1 FN + 1 Reduces the icon size on the desktop or the font sizes within one of the supported application windows. FN + 2 FN + 2 Enlarges the icon size on the desktop or the font sizes within one of the supported application windows. FN + Space FN + Space Changes the display resolution. FN + FN + Turns the keyboard backlight on or off.
Optical disc drives The computer may be installed with a DVD Super Multi drive or Blu-ray™ Writer drive (BDXL™). When the computer is accessing an optical disc, the indicator on the drive glows. Formats The drives support the following formats.
2. Grasp the disc tray gently and pull until it is fully opened. Figure 4-2 Pressing the eject button and pulling the disc tray open 2 1 1. Eject button 3. 2. Disc tray Lay the disc, label side up, in the disc tray. Figure 4-3 Inserting a disc 1 1. Laser lens When the disc tray is fully opened, the edge of the computer will cover the disc tray slightly. Therefore, you will need to turn the disc at an angle when you place it in the disc tray. After seating the disc, however, make sure it lies flat.
If the disc is not seated properly when the disc tray is closed, the disc might be damaged. Also, the disc tray might not open fully when you press the eject button. Removing discs To remove the disc, follow the steps as detailed below: Do not press the eject button while the computer is accessing the optical disc drive. Wait for the optical disc drive indicator to go out before you open the disc tray. Also, if the disc is spinning when you open the disc tray, wait for it to stop before you remove it. 1.
Writable discs This section describes the types of writable discs. Check the specifications of your drive to see the types of discs it can write. CDs CD-R discs can be written only once. The recorded data cannot be erased or changed. CD-RW discs including multi speed CD-RW discs, high-speed CD-RW discs and ultra-speed CD-RW discs can be recorded more than once. DVDs DVD-R, DVD+R, DVD-R DL and DVD+R DL discs can be written only once. The recorded data cannot be erased or changed.
in this section. If you fail to do so, you may find that the optical disc drive may not function properly, and you may fail to write or rewrite information successfully - this may cause you to either lose data or incur other damage to the drive or media. Disclaimer TOSHIBA does not assume responsibility for the following: Damage to any disc that may be caused by writing or rewriting with this product.
DVD+R: MITSUBISHI KAGAKU MEDIA CO., LTD. (for 8x and 16x speed media) TAIYO YUDEN CO., Ltd. (for 8x and 16x speed media) DVD+R DL: MITSUBISHI KAGAKU MEDIA CO., LTD. (for 8x speed media) DVD-RW: DVD Specifications for Recordable Disc for Version 1.1 or version 1.2 Victor Company of Japan, Ltd. (JVC) (for 2x, 4x and 6x speed media) MITSUBISHI KAGAKU MEDIA CO., LTD. (for 2x, 4x and 6x speed media) DVD+RW: MITSUBISHI KAGAKU MEDIA CO., LTD.
When writing or rewriting Please observe the following points while you write or rewrite data to a media: Always copy data from the hard disk drive to the optical media - do not use the cut-and-paste function as the original data will be lost if there is a write error. Do not perform any of the following actions: Change users in the Operating Systems. Operate the computer for any other function, including such tasks as using a mouse or Touch Pad, or closing/opening the display panel.
Close all other applications when using the CyberLink PowerDVD for TOSHIBA. Do not open any other applications or carry out any other operations during video playback. Playback may stop or not function properly in some situations. Unfinalized DVDs created on home DVD recorders may not be playable on the computer. Use DVD-Video discs with a region code which is either "the same as the factory default setting" (if applicable) or "ALL".
Display Devices & Audio If the video image is not displayed on an external display or television, stop the CyberLink PowerDVD for TOSHIBA, and change the screen resolution. To change the screen resolution, click Desktop Assist -> Control Panel -> Appearance and Personalization -> Display -> Adjust resolution on the desktop. However, video cannot be output to some external displays and televisions due to output or playback conditions.
Notes on use This software can only be used on Windows operating system. TOSHIBA VIDEO PLAYER is only provided with models configured with a DVD Super Multi drive and UHD (3840 x 2160 pixels) LCD screen. TOSHIBA VIDEO PLAYER software is supported for playback of DVD and video file. Frame dropping, audio skipping or out of sync audio and video may occur during playback of some video titles. Close all other applications when using the TOSHIBA VIDEO PLAYER.
Carry out the installation/uninstallation of the TOSHIBA VIDEO PLAYER under a user account with administrator rights. Do not change Windows Users while TOSHIBA VIDEO PLAYER is running. For some DVD or video files, using the control window to change the audio track will also change the subtitle track. This software can only playback MPEG2, MP4 and WTV files created by the preinstalled applications on the same computer. Playback may not function properly if you use the files other than these types.
If the menu is opened in the Display Area using the Control Panel's Top Menu or Menu buttons, Touch Pad and mouse menu operations may not be able to be used. Open TOSHIBA VIDEO PLAYER Manual TOSHIBA VIDEO PLAYER features and instructions are explained in details in TOSHIBA VIDEO PLAYER Manual. Use the following procedure to open TOSHIBA VIDEO PLAYER Manual. Press the F1 key when TOSHIBA VIDEO PLAYER is launched and click the Help button.
Do not playback video while recording television programs using other applications. Doing so may cause video playback or television program recording errors. In addition, if pre-scheduled recording starts during video playback it may cause video playback or television program recording errors. Please view video during times when there is no recording prescheduled. While playing a BD-J title, keyboard shortcut is ineffective. Resume play function cannot be used with some discs on TOSHIBA Blu-ray Disc Player.
Do not change the display device while running the TOSHIBA Blu-ray Disc Player. Starting TOSHIBA Blu-ray Disc Player Use the following procedure to start TOSHIBA Blu-ray Disc Player. Insert a Blu-ray™ Movie Disc in the optical disc drive while the operating system is running. When a Blu-ray™ Movie Disc is set in the Blu-ray™ drive (for models with Blu-ray™ drive), TOSHIBA Blu-ray Disc Player may start automatically. Click Desktop Assist -> Media & Entertainment -> TOSHIBA Bluray Disc Player on the desktop.
Important Safety Information for 3D Function Please refrain from or stop viewing if you feel ill or experience discomfort before or while watching 3D video images. Please refrain from viewing 3D video images if you experience convulsions, photosensitivity reaction, or heart disease. Due to the possibility of impact on vision development, viewers of 3D video images should be aged 6 or older.
The TOSHIBA VIDEO PLAYER is intended for playing DVD-Video, DVD-VR and video files and for viewing 2D home video content in 3D. The 3D playback of any video content not created by the user may require the permission of third parties, where such content is protected by copyright. The protection of intellectual property rights is essential for TOSHIBA. In this respect, TOSHIBA underlines that the Player should not be used in a manner infringing such rights.
Notes on 3D Playback for TOSHIBA Blu-ray Disc Player The 3D playback function can playback 3D video content, and your 2D home video content and other 2D content created by you (DVD or video file) in 3D using real-time 2Dto3D conversion. The 3D playback function CANNOT be used to playback 2D video contents of Blu-ray Disc or AVCHD in 3D using real-time 2Dto3D conversion. The Player's 3D playback function is meant for only personal home use.
Depending on the system environment, the player may automatically switch into 2D if you perform any of the following operations during 3D playback. Furthermore, you may experience some time lag when the switching occurs. - Opening windows or pop-ups such as [Right-Click Menu], [Settings Window], [File Select] or [Error Message]. - Using Windows features. - Using any other applications. Please make sure to use AC adapter when playing with 3D playback feature enabled.
Battery This section explains battery types, use, recharging methods and handling. Battery types The computer has different types of batteries. Battery pack When the AC adaptor is not connected, the computer's main power source is this lithium ion battery pack, also referred to in this manual as the main battery.
Procedures To recharge a battery pack, connect the AC adaptor to the DC IN 19V jack and plug the other end into a working outlet - the DC IN/Battery indicator will glow amber while the battery is being charged. Charging Time The following table shows the approximate time required to fully charge a discharged battery. Battery type Power off Power on Battery pack (43Wh, 4 cell) about 3.
Monitoring battery capacity Remaining battery power can be monitored using the following methods. Clicking the battery icon on the Windows Taskbar Via the Battery Status in the Windows Mobility Center window You should wait at least 16 seconds after turning on the computer before trying to monitor the remaining operating time.
Battery type Sleep Mode Shut Down Mode Battery pack (43Wh, 4 cell) about 30 hours about 15 days Extending battery life To maximize the life of your battery packs: At least once a month, disconnect the computer from a power source and operate it on battery power until the battery pack fully discharges. Before doing so, follow the steps as detailed below. 1. Turn off the computer's power. 2. Disconnect the AC adaptor and turn on the computer's power - if it does not turn on then go to Step 4. 3.
The Link speed (10/100/1000 megabits per second) changes automatically depending on the network conditions (connected device, cable or noise and so on). LAN cable types The computer must be configured properly before connecting to a LAN. Logging onto a LAN using the computer’s default settings could cause a malfunction in LAN operation. Check with your LAN administrator regarding set-up procedures.
2. Plug one end of the cable into the LAN jack. Press gently until you hear the latch click into place. Figure 4-5 Connecting the LAN cable 2 1 1. LAN jack 3. 2. LAN cable Plug the other end of the cable into a LAN hub connector or router. Check with your LAN administrator and hardware or software vendor before using or configuring a network connection. Additional memory module You can install additional memory into the computer in order to increase the amount of system memory that is available.
Additional memory module is a precision electronic component that may be fatally damaged by static electricity. Since the human body can carry static electricity, it is important that you discharge yourself before touching or installing any additional memory modules. To discharge your body’s static electricity, simply touch any metal close to you with bare hands. Use a point size 0 Phillips screwdriver to remove and fasten the screws the use of an incorrect screwdriver can damage the screw heads.
7. Align the notch of the memory module with that of the memory slot and gently insert the module into the slot at about a 30 degree angle before holding it down until the latches on either side snap into place. Figure 4-7 Seating the memory module 1 2 3 1. Notch 2. Slot B 3. Slot A Never allow metal objects, such as screws, staples and paper clips, to enter the computer. Foreign metal objects can create a short circuit, which can cause computer damage and fire, possibly resulting in serious injury.
8. Seat the memory module cover in place and secure it with the screw. Take care to ensure that the memory module cover is firmly closed. Figure 4-8 Seating the memory module cover 1 2 1. Memory module cover 2. Screw 9. Turn your computer over. 10. Connect the AC adaptor and turn the computer on. Make sure the added memory is recognized - to confirmed it, click Desktop Assist -> Control Panel -> System and Security -> System on the desktop.
8. Grasp the module by its edges and remove it from the computer. If you use the computer for a long time, the memory modules and the circuits locating close to the memory modules will become hot. In this case, let them cool to room temperature before you replace them. Or you will get burnt if you touch any of them. Do not touch the connectors on the memory module or on the computer. Debris on the connectors may cause memory access problems. Figure 4-9 Removing the memory module 1 1 1.
Please note that an adaptor is required to use miniSD/microSD Card. Please note that not all memory media have been tested and verified to work correctly. Therefore, it is not possible to guarantee that all memory media will operate properly.
Formatting a memory media card Memory media cards are sold already formatted in conformity to specific standards. If you reformat a memory card, be sure to reformat it with a device such as digital camera or digital audio player that uses the memory cards, not with the format command provided within Windows. Should you need to format all areas of the memory card, including the protected area, you will need to obtain an appropriate application that applies the copy protection system.
Inserting memory media The following instructions apply to all types of supported media devices. To insert memory media, follow the steps as detailed below: 1. 2. 3. Turn the memory media so that the contacts (metal areas) face down. Insert the memory media into the memory media slot on the computer. Press the memory media gently until it clicks into place. Figure 4-11 Inserting memory media 1 1. Memory media slot 2 2. Memory media Make sure the memory media is oriented properly before you insert it.
Do not remove only the miniSD/microSD Card while leaving the adaptor in the memory media slot. External Display Your computer video capabilities can be enhanced with additional displays. External displays allows you to share your desktop or extend the desktop area. Connecting an external display Your computer comes with a built-in display, but you can also connect other external displays via available ports on the computer.
Figure 4-12 Connecting the HDMI out port 2 1 1. HDMI out port 2. HDMI cable Please do not plug/unplug an HDMI device under the following conditions: The system is starting up. The system is shutting down. When you connect a television or external monitor to the HDMI port, the display output device is set to HDMI. When you unplug the HDMI cable and re-plug it, please wait at least 5 seconds before you re-plug the HDMI cable again.
Selecting HD Format To select the display mode, follow the steps as below: 1. 2. Click Desktop Assist -> Control Panel -> Appearance and Personalization -> Display -> Change display settings -> Advanced settings -> List All Modes on the desktop. Select one of the modes at List All Modes. Wireless display Your computer may support Wireless display, a wireless technology which utilizes Wi-Fi to allow the computer to be wirelessly connected to external displays including TVs as extended screens.
Security lock A security lock enables you to anchor your computer to a desk or other heavy object in order to help prevent unauthorized removal or theft. The computer has a security lock slot on its right side into which you can attach one end of the security cable, while the other end attaches to a desk or similar object. The methods used for attaching security cables differ from product to product. Please refer to the instructions for the product you are using for more information.
Volume Mixer The Volume Mixer utility lets you control the audio volume for playback of devices and applications under Windows. To launch the Volume Mixer utility, right click on the speaker icon on the Windows Taskbar, and then select Open Volume Mixer from the sub menu. To adjust the volume level of speakers or headphones, move the Speakers slider. To adjust the volume level of an application that you are using, move the slider for the corresponding application.
To open the Screen Resolution dialog, click Desktop Assist -> Control Panel -> Appearance and Personalization -> Display -> Change display settings on the desktop. If you are running some applications (for example a 3D application or video playback), you may see some disturbance, flickering or frame dropping on your screen. If that occurs, adjust the resolution of display, lowering it until the screen is displayed properly.
Chapter 5 Utilities and Advanced Usage This chapter describes the utilities and special features of this computer, and the advanced usage of some utilities. Utilities and Applications This section describes the pre-installed utilities that come with the computer and details how to start them. For further information on their operation, you may refer to each utility's online manual, help files or README.TXT file (if applicable).
TOSHIBA Display Utility TOSHIBA Display Utility includes Desktop Text Size utility, Split Screen utility, Resolution+ settings or Task Switcher utility. Desktop Text Size allows you to make the text size bigger or smaller on the desktop according to your usage and favorite. You can change the text size on the display and on the title bar of windows by changing the scaling of the text size.
TOSHIBA HDD Protection This feature uses the acceleration sensor built in the computer to detect vibration and shocks, and automatically moves the hard disk drive's read/ write head to a safe position in order to reduce the risk of damage that could be caused by headto-disk contact. Refer to the Using the Hard Disk Drive (HDD) Protection section for more details. CyberLink PowerDVD This software is provided for playback of DVD for TOSHIBA Video.
TOSHIBA eco Utility This computer is equipped with "eco mode". This mode slightly lowers performance of some devices to reduce electric power consumption. You can realize measurable power savings by using it continuously. TOSHIBA eco Utility helps control the power consumption of your computer. Various information can help you understand your degree of contribution to the environment.
CyberLink MediaStory CyberLink MediaStory helps you to quickly manage and share your multimedia content. Your photos and videos are organized by event, date in a calendar, geographical places, and by people's faces. You can easily create a polished slideshow or video of your digital life utilizing your photos and videos. This utility will not be provided if CyberLink MediaShow is installed. To access it, click CyberLink MediaStory in the Apps view.
TOSHIBA PC Health Monitor The TOSHIBA PC Health Monitor application proactively monitors a number of system functions such as power consumption, battery health and system cooling, informing you of significant system conditions. This application recognizes the system and individual component serial numbers and will track specific activities related to their usage. To access this utility, click Desktop Assist -> Support & Recovery -> PC Health Monitor on the desktop.
Display automatic power off *1 This feature automatically cuts off power to the computer's display panel when there is no keyboard input for a specified time, with power being restored the next time a key is pressed. This can be specified in the Power Options. HDD automatic power This feature automatically cuts off power to the hard disk drive when it is not accessed for a off *1 specified time, with power being restored when the hard disk drive is next accessed.
Hibernation Mode This feature lets you turn off the power to the computer without exiting from your software. The contents of main memory are automatically saved to the Hard Disk Drive so that when you next turn the power on again, you can continue working right where you left off. Refer to the Turning off the power section, for more details. USB Wakeup function This function restores the computer from Sleep Mode depending on the external devices connected to the USB ports.
Desktop Assist -> Tools & Utilities -> Password Utility -> User Password User authentication may be required to validate user rights when using TOSHIBA Password Utility to delete or change passwords, etc. Set (button) Click this button to register a password. After a password is set, you will be prompted to enter it when you start the computer. After you set the password, a dialog box will be displayed asking whether you want to save it to other media.
If you forget your HDD User Password, TOSHIBA will NOT be able to assist you, and your HDD will be rendered COMPLETELY and PERMANENTLY INOPERABLE. TOSHIBA will NOT be held responsible for any loss of any data, any loss of use or access to your HDD, or for any other losses to you or any other person or organization that result from the loss of access to your HDD. If you can’t accept this risk, don’t register the HDD User Password. When saving the HDD User Password shut down or restart the computer.
3. Press ENTER. If you enter the password incorrectly three times in a row, or if you don’t enter the password within 1 minute, the computer shuts off. In this case, some features that can power on the computer automatically (Wake-up on LAN, Task Scheduler, etc) may not work. You must turn the computer back on to retry password entry. TOSHIBA System Settings TOSHIBA System Settings is the TOSHIBA configuration management tool available through the Windows operating system.
After you changed the settings, a dialog box may appear to prompt you that the changes will take effect after the computer is restarted. Make sure to restart your computer immediately to apply these changes. USB Charge Your computer can supply USB Bus power (DC5V) to the USB port.
When there is a current overflow of the external devices connected to the compatible ports, USB bus power (DC5V) supply may be stopped for safety reasons. When Sleep and Charge function is enabled, the USB Wakeup function may not work for compatible ports. In that case, if there is a USB port that does not have the Sleep and Charge function, attach the mouse or keyboard to it. If all USB ports have the Sleep and Charge function, change to disable Sleep and Charge function.
System ON CDP Charge This function enable/disable CDP (Charging Downstream Port) to use rapid USB charge while the computer is powered on. When "System ON CDP Charge Mode" is enabled, your computer can supply USB bus power (DC5V, 1.5A) to the compatible ports while the computer is turned on. To set System ON CDP Charge Mode, click Desktop Assist -> Tools & Utilities -> System Settings -> USB on the desktop. Enabled Rapid USB battery charge at maximum 1.5A while PC is powered On.
When Sleep and Music function is enabled, it is possible to play sound from the computer’s speaker by connecting an audio cable to the Microphone jack. Using this function discharges the computer’s battery. Therefore, it is recommended that the computer be connected to an external power source via the AC Adaptor. When using the Sleep and Music function, connect the computer and Audio device with an audio cable. When using the Sleep and Music function, the volume level can not be changed from the computer.
The screen saver is disabled while TOSHIBA Media Player is playing a video file or slideshows of photos. The computer will not enter Sleep and Hibernation mode automatically, while TOSHIBA Media Player is running. The display automatic power off function is disabled while TOSHIBA Media Player is playing a video file or slideshows of photos. The Resolution+ function was specially adjusted for the internal monitor. Hence, please turn OFF Resolution+ when viewing on external monitor.
Opening TOSHIBA Media Player by sMedio TrueLink+ Manual The features and operations about TOSHIBA Media Player are explained in the TOSHIBA Media Player Manual. Use the following procedure to open TOSHIBA Media Player Online help: When TOSHIBA Media Player is running, click Help of the Settings charm. Using CyberLink MediaShow 6 for TOSHIBA This feature is supported by some models.
Make sure that your computer is running on AC power while using CyberLink MediaShow. Operate the computer at Full Power. Do not use power-saving features. CyberLink MediaShow cannot edit or play copy-protected content. Do not enter Sleep or Hibernation Mode while using CyberLink MediaShow. Do not operate CyberLink MediaShow immediately after turning on the computer. Please wait until all Disc Drive activity has stopped. Do not run software like a screen saver because it can put a heavy load on the CPU.
If you use an over-used rewritable disc, the full formatting might be locked. Please use a brand new disc. Internet Connection An Internet connection is required for uploading and downloading. TOSHIBA PC Health Monitor The TOSHIBA PC Health Monitor application proactively monitors a number of system functions such as power consumption, battery health (for models with battery) and the system cooling, informing you of significant system conditions.
Starting the TOSHIBA PC Health Monitor The TOSHIBA PC Health Monitor can be opened by clicking Desktop Assist -> Support & Recovery -> PC Health Monitor on the desktop. The TOSHIBA PC Health Monitor main screen will be displayed. This utility may be disabled by default on your computer. You can enable it by clicking Please click here to enable TOSHIBA PC Health Monitor. The "PC Health Monitor Software Notice & Acceptance" screen will be displayed. Please carefully read the information displayed.
To open the utility, click Desktop Assist -> Tools & Utilities -> System Settings -> HDD Protection on the desktop. The utility can also be started from the icon on the Windows Taskbar or from the Control Panel. HDD Protection You can enable or disable HDD Protection by moving the slider to the right or left. HDD Protection does not work when the computer is booting, in Sleep Mode, in Hibernation Mode, in transition to Hibernation Mode, recovering from Hibernation Mode, or powered off.
the detection level automatically switches according to the power connection mode. Detection Level Amplification When the AC adaptor is disconnected, HDD Detection assumes that the computer will be carried and sets the detection level to the maximum for 10 seconds. Default You can reset HDD Protection settings to factory default by first clicking Default button and then Apply button.
Be sure to connect the AC adaptor when you create Recovery Media. Be sure to close all other software programs except the Recovery Media Creator. Do not run software such as screen savers which can put a heavy load on the CPU. Operate the computer at full power. Do not use power-saving features. Do not write to the media when the virus check software is running. Wait for it to finish, then disable virus detection programs including any software that checks files automatically in the background.
Restoring the pre-installed software from your created Recovery Media If the pre-installed files are damaged, you are able to use the Recovery Media you have created to restore the computer to the state it was in when you originally received it. To perform this restoration, follow the steps below: When you reinstall the Windows operating system, the hard disk will be reformatted and all data will be lost. Please make sure that the Boot Speed is set to Normal.
However, if you have already created a "Recovery Media", you can use it to restore the recovery partition. If you have not created "Recovery Media", please contact TOSHIBA support for assistance. Restoring the pre-installed software from the Recovery Hard Disk Drive A portion of the total Hard Disk Drive space is configured as a hidden recovery partition. This partition stores files which can be used to restore pre-installed software in the event of a problem.
Chapter 6 Troubleshooting TOSHIBA has designed this computer for durability, however, should problems occur you are able to use the procedures detailed in this chapter to help determine the cause. All users should become familiar with this chapter as knowing what might go wrong can help prevent problems from occurring in the first place.
Check all cables to ensure they are correctly and firmly attached to the computer - loose cables can cause signal errors. Inspect all connecting cables for loose wires and all connectors for loose pins. Check that your disc media is correctly loaded Always try to make detailed notes of your observations and keep them in a permanent error log - this will help you to describe your problems to TOSHIBA Support. In addition, if a problem recurs, the log you have made will help to identify the problem faster.
Hardware If you cannot find a software problem, you should then check the setup and configuration of your hardware. First run through the items in the preliminary checklist as described previously then, if you still cannot correct the problem, try to identify the source - the next section provides checklists for individual components and peripherals.
If the indicator is glowing, the computer is on. Also, try turning the computer off and then on. If you are using an AC adaptor, verify that the computer is receiving power from the external power source by looking at the DC IN/Battery indicator. If the indicator is glowing, the computer is connected to a live external power source. The computer will not load advanced options during startup By holding down one of the following keys during startup, your computer will load advanced options as shown below.
Overheating power down If the processor's temperature reaches an unacceptably high level with either setting, the computer will automatically shut down to prevent any damage - in this instance all unsaved data in memory will be lost. Problem Procedure Computer shuts down automatically. Leave the computer off until the it reaches room temperature. If the computer has reached room temperature and it still does not start, or if it starts but shuts down quickly, contact TOSHIBA Support.
Problem Procedure Battery doesn’t power the computer as long as expected If you frequently recharge a partially charged battery, the battery might not charge to its full potential - in these instances you should fully discharge the battery and then attempt to charge it again. Check the Power saver option under Select a power plan in the Power Options. Real Time Clock Problem Procedure The BIOS setting and system date/ time are lost.
Internal display panel Apparent computer's display panel problems may be related to the computer's setup and configuration. Problem Procedure No display Press the function keys to adjust the display priority, and to make sure it is not set for output to an external monitor. Markings appear on the computer's display panel These marks may have come from contact with the keyboard and Touch Pad while the display panel has been closed.
Problem Procedure You cannot access a Make sure the drive’s disc tray is securely closed. CD/DVD/Blu-ray Press gently until it clicks into place. Disc™ in the drive Open the disc tray and make sure the disc is properly seated. It should lie flat with the label facing up. A foreign object in the disc tray could block laser light from reading the disc. Make sure there is no obstruction. Remove any foreign object. Check whether the disc is dirty.
Problem Procedure On-screen pointer does not respond to pointing device operation In this instance the system might be busy - Try moving the mouse again after waiting a short while. Double-tapping (Touch Pad) does not work In this instance, you should initially try changing the double-click speed setting within the Mouse Control utility. 1. 2. 3. The on-screen pointer moves too fast or too slow In this instance, you should initially try changing the speed setting within the Mouse Control utility. 1.
Problem Procedure Double-clicking does In this instance, you should initially try changing not work the double-click speed setting within the Mouse Control utility. 1. 2. 3. The on-screen pointer moves too fast or too slow In this instance, you should initially try changing the speed setting within the Mouse Control utility. 1. 2. 3. The on-screen pointer moves erratically To access this utility, click Desktop Assist -> Control Panel -> Hardware and Sound -> Mouse on the desktop.
Sleep and Charge function For more information and settings, please refer to the USB Sleep and Charge section. Problem Procedure I cannot use the Sleep and Charge function. Sleep and Charge function may be disabled. Enable the Sleep and Charge function in the TOSHIBA System Settings. When there is a current overflow of the external device connected to the compatible port, USB bus power (DC5V) supply may be stopped for safety reasons.
Problem Procedure The "USB Wakeup function" does not work. When Sleep and Charge function is enabled, the "USB WakeUp" function does not work for ports that support the Sleep and Charge function. In that case, use an USB port that does not have the USB Sleep and Charge function or change to disable Sleep and Charge function. Sound system In addition to the information in this section, please also refer to the documentation supplied with your audio device.
Problem Procedure Monitor does not turn on After confirming that the monitor's power switch is on, you should check the connections to make sure that the power cord/adaptor is firmly connected to the monitor and to a working power outlet. No display Try adjusting the contrast and brightness controls on the external monitor. Press the function key in order to change the display priority and ensure that it is not set for the internal display only. Check to see if the external monitor is connected.
Problem Procedure Wake-up on LAN does not work Make sure the AC adaptor is connected. The Wake-up on LAN function consumes power even when the system is off. Check to make sure fast startup is disabled: 1. 2. 3. 4. 5. Click Desktop Assist -> Control Panel -> System and Security -> Power Options on the desktop. Click Choose what the power button does or Choose what closing the lid does. Click Change settings that are currently unavailable. Clear the Turn on fast startup check box.
TOSHIBA support If you require any additional help using your computer or if you are having problems operating the computer, you may need to contact TOSHIBA for additional technical assistance. Before you call Some problems you experience may be related to software or the operating system so it is important that you investigate other sources of assistance first.
Chapter 7 Appendix Specifications This section summarizes the computer’s technical specifications. Physical Dimensions Physical Dimensions shown below do not include parts that extend beyond the main body. The physical dimensions may vary depending on the model you purchased. Size Approximately 377.5 (w) x 244.0 (d) x 27.0/27.0 (h) millimeters Approximately 377.5 (w) x 244.0 (d) x 27.9/27.9 (h) millimeters (not including parts that extend beyond the main body).
Computer 19V DC External RGB monitor port pin assignment 5 1 15 11 10 6 Pin Signal Name Description I/O 1 CRV Red Video Signal O 2 CGV Green Video Signal O 3 CBV Blue Video Signal O 4 Reserved Reserved 5 GND Ground 6 GND Ground 7 GND Ground 8 GND Ground 9 +5V Power Supply 10 GND Ground 11 Reserved Reserved 12 SDA Data Signal I/O 13 HSYNC Horizontal Sync Signal O 14 VSYNC Vertical Sync Signal O 15 SCL Data Clock Signal O I/O (I): Input to comput
Current rating: Minimum 2.5 amperes Certification agencies China: CQC U.S. and Canada: UL listed and CSA certified No.
Australia Europe AS approved Approved by the appropriate agency Canada China CSA approved CCC approved Information for Wireless Devices Wireless Technology Interoperability The Wireless LAN is compatible with other LAN systems Direct Sequence Spread Spectrum (DSSS) /Orthogonal Frequency Division Multiplexing (OFDM) radio technology, and is compliant to: The IEEE 802.
http://www.pc.support.global.toshiba.com if you have any questions about using Wireless LAN or Bluetooth Module. In Europe visit http://www.toshiba-europe.com/computers/tnt/bluetooth.htm Wireless Devices and your health Wireless products, like other radio devices, emit radio frequency electromagnetic energy. The level of energy emitted by Wireless products however is far much less than the electromagnetic energy emitted by wireless devices like for example mobile phones.
Always turn off wireless functionality if the computer is near automatic control equipment or appliances such as automatic doors or fire detectors. Radio waves can cause malfunction of such equipment, possibly resulting in serious injury. It may not be possible to make a network connection to a specified network name using the ad hoc network function. If this occurs, the new network (*) will have to be configured for all computers connected to the same network in order to re-enable network connections.
The range of your wireless devices can be affected when the antennas are placed near metal surfaces and solid high-density materials. Range is also impacted due to "obstacles" in the signal path of the radio that may either absorb or reflect the radio signal. Radio Frequency Interference Requirements This device is restricted to indoor use due to its operation in the 5.15 to 5.25GHz frequency range. High-power radars are allocated as primary users (i.e. priority users) of the bands 5.25 to 5.35GHz and 5.
Europe Restrictions for Use of 2400.0-2483.5MHz Frequencies in Europe France: Outdoor use limited to 10mW e.i.r.p. within the band 2454-2483.5MHz Military Radiolocation use.Refarming of the 2.4GHz band has been ongoing in recent years to allow current relaxed regulation Full implementation planned 2012. Italy: - For private use, a general authorization is required if WAS/ RLAN’s are used outside own premises. For public use, a general authorization is required.
Russian Federation: Limited e.i.r.p 100mW. Permitted to use only for indoor applications, closed industrial and warehouse areas, and on board aircraft. 1. 2. Permitted to use for local networks of aircraft crew service communications on board aircraft in area of the airport and at all stages of flight. Permitted to use for public wireless access local networks on board aircraft during a flight at the altitude not less than 3000m.
check the current channel of operation. If operation is occurring outside of the allowable frequencies for outdoor use, as listed above, the user must contact the applicable national spectrum regulator to request a license for outdoor operation. Canada - Industry Canada (IC) This device complies with RSS-210 of the Industry Canada Rules.
The installer of this radio equipment must ensure that the antenna is located or pointed such that it does not emit RF field in excess of Health Canada limits for the general population; consult Safety Code 6, obtainable from Health Canada’s website www.hc-sc.gc.
2. 3. If this equipment causes RF interference to other radio stations, promptly change the frequency being used, change the location of use, or turn off the source of emissions. Contact an authorized TOSHIBA service provider if you have problems with interference caused by this product to Other Radio Stations. 2. Indication for Wireless LAN The indication shown below appears on this equipment. (1)(2) (3)(4) (5) 1. 2. 3. 4. 5. 2.4 : This equipment uses a frequency of 2.4GHz.
Device Authorization This device obtains the Technical Regulation Conformity Certification and it belongs to the device class of radio equipment of low-power data communication system radio station stipulated in the Telecommunications Business Law of Japan. Intel® Centrino® Wireless-AC 7260 Wireless LAN and Bluetooth The Name of the radio equipment: 7260NGW DSP Research, Inc.
Cyprus Czech Rep Denmark Estonia Finland France Germany Greece Hong Kong Hungary Iceland India Indonesia Ireland Italy Japan Korea Latvia Liechtenstein Lithuania Luxemburg Malta Monaco Netherlands Norway Philippines Poland Portugal Romania Slovak Republic Slovenia Spain Sweden Switzerland UK USA Legal Footnotes Non-applicable Icons Certain computer chassis are designed to accommodate all possible configurations for an entire product series.
Under some conditions, your computer product may automatically shutdown. This is a normal protective feature designed to reduce the risk of lost data or damage to the product when used outside recommended conditions. To avoid risk of lost data, always make back-up copies of data by periodically storing it on an external storage medium. For optimum performance, use your computer product only under recommended conditions. Read additional restrictions in your product documentation.
time of publication. Recharge time varies depending on usage. Battery may not charge while computer is consuming full power. After going through many charge and discharge cycles, the battery will lose its ability to perform at maximum capacity and will need to be replaced. This is a normal phenomenon for all batteries. To purchase a new battery pack, see the accessories information that is shipped with your computer.
Copy Protection Applicable copy protection standards included in certain media may prevent or limit recording or viewing of the media.
Index A Documentation list 2-1 Dual Pointing Device Touch Pad 6-8 AC adaptor additional 4-40 connecting 2-3 DC IN 19V jack 3-2 DVD Super Multi drive using writing ASCII characters 4-5 E B Battery extending life 4-27 monitoring capacity 4-26 real time clock 4-24 save mode 5-7 types 4-24 Equipment checklist 2-1 External monitor problems 6-13 G Battery indicator Bluetooth 7-7 C Graphics Processing Unit 3-10 H Hard disk drive automatic power off 5-7 Cleaning the computer 1-17 Cooling vents 3-4, 3-5
L Hibernation Mode 2-11 panel on/off 5-7 Shut Down mode 2-8 Sleep Mode 2-9 turning off 2-8 turning on 2-6 LAN cable types 4-28 connecting 4-28 M Problems AC power 6-5 Analyzing the problem 6-2 Battery 6-5 Dual Pointing device 6-8 External monitor 6-12 Hardware and system checklist 6-4 HDD 6-7 Internal display panel 6-7 Keyboard 6-6 Memory Media Card 6-8 Overheating power down 6-5 Power 6-4 Real Time Clock 6-6 Sound system 6-12 TOSHIBA support 6-15 Touch Pad 6-8 USB device 6-10 USB mouse 6-9 Media care
setting 2-9 System automatic 5-7 Sound system problems 6-12 T TOSHIBA Desktop Assist 5-1 Touch Screen U USB device problems 6-10 V Video mode 4-41 Video RAM 3-10 W Web Camera 3-6 Wireless communication 7-5 User's Manual Index-3
