User's Manual TECRA A50-A/W50-A Satellite Pro A50-A
Table of Contents Chapter 1 TOSHIBA Legal, Regulatory and Safety Copyright, Disclaimer and Trademarks .............................................. 1-1 Regulatory Information ......................................................................... 1-2 Video Standard Notice .......................................................................... 1-8 OpenSSL Toolkit License Issues ......................................................... 1-8 FreeType License Issues .......................................
Wireless WAN Device ......................................................................... 4-28 LAN ....................................................................................................... 4-30 Additional memory module ................................................................ 4-31 Memory media ..................................................................................... 4-42 ExpressCard ........................................................................................
Chapter 1 TOSHIBA Legal, Regulatory and Safety This chapter states the Legal, regulatory and safety information applicable to TOSHIBA computers. Copyright, Disclaimer and Trademarks Copyright © 2013 by TOSHIBA Corporation. All rights reserved. Under the copyright laws, this manual cannot be reproduced in any form without the prior written permission of TOSHIBA. No patent liability is assumed, with respect to the use of the information contained herein.
Windows, Microsoft and Windows logo are registered trademarks of Microsoft Corporation. The Bluetooth® word mark and logos are registered trademarks owned by Bluetooth SIG, Inc. and any use of such marks by Toshiba Corporation and its affiliates is under license. The terms HDMI and HDMI High-Definition Multimedia Interface, and the HDMI Logo are trademarks or registered trademarks of HDMI Licensing LLC in the United States and other countries.
turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help.
EU Declaration of Conformity This product is carrying the CE-Mark in accordance with the related European Directives. Responsible for CE-Marking is TOSHIBA EUROPE GMBH, Hammfelddamm 8, 41460 Neuss, Germany. The complete and official EU Declaration of Conformity can be found on TOSHIBA’s web site http://epps.toshiba-teg.com on the Internet.
Any consequences resulting from the use of this product in working environments that are not approved are not the responsibility of TOSHIBA. The consequences of the use of this product in non-approved working environments may be: Interference with other devices or machines in the near surrounding area. Malfunction of, or data loss from, this product caused by disturbances generated by other devices or machines in the near surrounding area.
Following information is only valid for EU-member States: Disposal of products The crossed out wheeled dust bin symbol indicates that products must be collected and disposed of separately from household waste. Integrated batteries and accumulators can be disposed of with the product. They will be separated at the recycling centres. The black bar indicates that the product was placed on the market after August 13, 2005.
These symbols may not stick depending on the country and region where you purchased. REACH - Compliance Statement The new European Union (EU) chemical regulation, REACH (Registration, Evaluation, Authorization and Restriction of Chemicals), entered into force on 1 June 2007. TOSHIBA will meet all REACH requirements and is committed to provide our customers with information about the chemical substances in our products according to REACH regulation. Please consult the following website www.toshiba-europe.
Video Standard Notice THIS PRODUCT IS LICENSED UNDER THE AVC, THE VC-1 AND MPEG-4 VISUAL PATENT PORTFOLIO LICENSE FOR THE PERSONAL AND NON-COMMERCIAL USE OF A CONSUMER FOR (I) ENCODING VIDEO IN COMPLIANCE WITH THE ABOVE STANDARDS ("VIDEO") AND/OR (II) DECODING AVC, VC-1 AND MPEG-4 VIDEO THAT WAS ENCODED BY A CONSUMER ENGAGED IN A PERSONAL AND NONCOMMERCIAL ACTIVITY AND/OR WAS OBTAINED FROM A VIDEO PROVIDER LICENSED BY MPEG LA TO PROVIDE SUCH VIDEO.
5. 6. Products derived from this software may not be called "OpenSSL" nor may "OpenSSL" appear in their names without prior written permission of the OpenSSL Project. Redistributions of any form whatsoever must retain the following acknowledgment: "This product includes software developed by the OpenSSL Project for use in the OpenSSL Toolkit (http://www.openssl.
This can be in the form of a textual message at program startup or in documentation (online or textual) provided with the package. Redistribution and use in source and binary forms, with or without modification, are permitted provided that the following conditions are met: 1. 2. 3. Redistributions of source code must retain the copyright notice, this list of conditions and the following disclaimer.
Copyright 1996-2002, 2006 by David Turner, Robert Wilhelm, and Werner Lemberg Introduction ============ The FreeType Project is distributed in several archive packages; some of them may contain, in addition to the FreeType font engine, various tools and contributions which rely on, or relate to, the FreeType Project. This license applies to all files found in such packages, and which do not fall under their own explicit license.
authors (David Turner, Robert Wilhelm, and Werner Lemberg) as the `FreeType Project', be they named as alpha, beta or final release. `You' refers to the licensee, or person using the project, where `using' is a generic term including compiling the project's source code as well as linking it to form a `program' or `executable'. This program is referred to as `a program using the FreeType engine'.
-------------Neither the FreeType authors and contributors nor you shall use the name of the other for commercial, advertising, or promotional purposes without specific prior written permission. We suggest, but do not require, that you use one or more of the following phrases to refer to this software in your documentation or advertising materials: `FreeType Project', `FreeType Engine', `FreeType library', or `FreeType Distribution'. As you have not signed this license, you are not required to accept it.
ENERGY STAR® Program Your Computer model may be ENERGY STAR® compliant. If the model you purchased is compliant, it is labeled with the ENERGY STAR logo on the computer and the following information applies. TOSHIBA is a partner in the ENERGY STAR Program and has designed this computer to meet the latest ENERGY STAR guidelines for energy efficiency.
Optical disc drive safety instructions Be sure to check the precautions at the end of this section. The drive model employs a laser system. To ensure proper use of this product, please read this instruction manual carefully and retain for future reference. Should the unit ever require maintenance, contact an authorized service location. Use of controls, adjustments or the performance of procedures other than those specified may result in hazardous radiation exposure.
General Precautions TOSHIBA computers are designed to optimize safety, minimize strain and withstand the rigors of portability. However, certain precautions should be observed to further reduce the risk of personal injury or damage to the computer. Be certain to read the general precautions below and to note the cautions included in the text of the manual.
Stress injury Carefully read the Instruction Manual for Safety and Comfort. It contains information on the prevention of stress injuries to your hands and wrists that can be caused by extensive keyboard use. It also includes information on work space design, posture and lighting that can help reduce physical stress. Heat injury Avoid prolonged physical contact with the computer. If the computer is used for long periods, its surface can become very warm.
Moving the computer While the computer is designed for flexible day-to-day usage you should exercise a few simple precautions when moving it in order to help ensure trouble-free operation. Make sure all disk/disc activity has ended before moving the computer. Turn off (shut down) the computer. Disconnect the AC adaptor and all peripherals before moving the computer. Close the display panel. Do not pick up the computer by its display panel.
Safety Icons Safety icons are used in this manual to bring important information to your attention. Each type of message is identified as shown below. Indicates a potentially hazardous situation, which could result in death or serious injury, if you do not follow instructions. A caution informs you that improper use of equipment or failure to follow instructions may cause data loss, equipment damage, or may result in minor or moderate injury. Please read.
Chapter 2 Getting Started This chapter provides an equipment checklist, and basic information to start using your computer. Some of the features described in this manual may not function properly if you use an operating system that was not pre-installed by TOSHIBA. Equipment checklist Carefully unpack your computer, taking care to save the box and packaging materials for future use.
Click Tap the Touch Pad or click the left Touch Pad control button once. Left click the mouse once. Tap the touch screen once (only for touch screen models). Right-click Click the right Touch Pad control button once. Right click the mouse once. Press and hold on the touch screen (only for touch screen models). Double-click Tap the Touch Pad or click the left Touch Pad control button twice. Left click the mouse twice. Tap the touch screen twice (only for touch screen models).
Use a virus-check program and make sure it is updated regularly. Never format storage media without checking its content - formatting destroys all stored data. It is a good idea to periodically back up the internal HDD/SSD or other main storage device to external media. General storage media is not durable or stable over long periods of time and under certain conditions may result in data loss. Before you install a device or application, save any data in memory to the HDD/SSD or other storage media.
When you connect the AC adaptor to the computer, always follow the steps in the exact order as described in this User’s Manual. Connecting the power cable to a live electrical outlet should be the last step otherwise the adaptor DC output plug could hold an electrical charge and cause an electrical shock or minor bodily injury when touched. As a general safety precaution, avoid touching any metal parts.
2. Connect the AC adaptor’s DC output plug to the DC IN 19V jack on your computer. Figure 2-4 Connecting the DC output plug to the computer 1 2 1 2 1. DC IN 19V jack 2. DC output plug Product appearance depends on the model you purchased. 3. Plug the power cord into a live wall outlet - the DC IN/Battery indicator should glow. Opening the display The display panel can be opened to a wide range of angles for optimal viewing.
Be careful not to open the display panel too far as this could put stress on the display panel’s hinges and cause damage. Do not press or push on the display panel. Do not lift the computer by the display panel. Do not close the display panel with pens or any other objects left in between the display panel and the keyboard.
Your computer may take a while the next time you turn it on, if: The battery pack was exhausted and is now recharged. The battery pack was exhausted but now has the power connected via the AC adaptor. The battery pack is re-installed/replaced. Initial setup The Windows Startup Screen will be the first screen displayed when you turn on the power. Follow the on-screen instructions on each screen in order to properly install the operating system.
Start This Charm takes you to the Start screen or, if already on the Start screen, returns you to your last app. Devices This Charm allows you to manage your hardware. Settings This Charm allows you to access your computer’s settings (volume, brightness, connecting to the internet, and more). Tiles Tiles can be accessed and launched from the Start screen. Typical Start screen tiles are the Desktop tile and Mail tile, as well as tiles representing all other applications downloaded to your system.
1. 2. If you have entered data, either save it to the HDD/SSD or to other storage media. Make sure all disk/disc activity has stopped before removing the disk/ disc. If you turn off the power while a disk (disc) is being accessed, you may lose data or damage the disk. Never turn off the power while an application is running. Doing so could cause loss of data. Never turn off the power, disconnect an external storage device or remove storage media during data read/write. Doing so can cause data loss. 3. 4.
data, which could interfere with aviation or other systems, possibly causing serious injury. Before entering Sleep Mode, be sure to save your data. Do not switch to Sleep Mode while transferring data to external media, such as USB devices, memory media or other external memory devices, as data will be lost. Do not install or remove a memory module while the computer is in Sleep Mode. The computer or the memory module could be damaged.
Close the display panel. Please note that this feature must be enabled within the Power Options. Press the power button. Please note that this feature must be enabled within the Power Options. When you turn the power back on, you can continue where you left off when you shut down the computer. When the computer is in Sleep Mode, the Power indicator will blink orange.
Saves power by shutting down the system when the computer receives no input or hardware access for the time period set by the System Hibernate feature. Allows the use of the panel power off feature. Starting Hibernation Mode To enter Hibernation Mode, follow the steps below. 1. 2. Click the Settings charm. Click Power and then select Hibernate. In order to show Hibernate in Power menu, you need to setup according to the following steps: 1.
Chapter 3 The Grand Tour This chapter identifies the various components of the computer - it is recommended that you become familiar with each before you operate the computer. Legal Footnote (Non-applicable Icons) For more information regarding Non-applicable Icons, please refer to the Legal Footnotes section. Please handle your computer carefully to avoid scratching or damaging the surface.
Memory media slot This slot lets you insert an SD™/SDHC™/ SDXC™ memory card, miniSD™/microSD™ Card and MultiMediaCard™. Refer to the Memory media section for more information. Keep foreign metal objects, such as screws, staples and paper clips, out of the Memory media slot. Foreign metal objects can create a short circuit, which can cause damage and fire, possibly resulting in serious injury.
Left side The following figures show the left side of the computer. Figure 3-2 The left side of the computer 8 1 3 2 1 7 1. Cooling vents 2. DisplayPort* 3. External RGB monitor port 4. eSATA/USB combo port* 4 3 5 4 6 5 5 5 6 5. Universal Serial Bus (USB 3.0) ports 6. Headphone/Microphone jack 7. HDMI out port* 8. Smart Card slot* * Provided with some models. Product appearance depends on the model you purchased. Cooling vents The cooling vents help the processor to avoid overheating.
Universal Serial Bus (USB 3.0) port Two Universal Serial Bus ports, which comply to the USB 3.0 standard, are provided on the left side of the computer. The USB 3.0 port is compliant with USB 3.0 standard and backward compatible with USB 2.0 devices. USB 3.0 port(s) may work as USB 2.0 port(s) when operating in USB Legacy Emulation mode. Please note that it is not possible to confirm the operation of all functions of all USB devices that are available.
Figure 3-3 The right side of the computer 1 2 3 4 5 6 1 2 3 3 5 8 1. ExpressCard slot or PC Card slot* 2. Optical disc drive* 3. Universal Serial Bus (USB 2.0) port* 4. Serial Connector* 7 7 5. LAN jack 6. DC IN 19V jack 7. Security lock slot 8. DC IN 19V jack * Provided with some models. Product appearance depends on the model you purchased. ExpressCard slot This slot allows you to install a single ExpressCard/54 device. Some models are equipped with a ExpressCard slot.
LAN jack This jack lets you connect to a LAN. The adaptor has built-in support for Ethernet LAN (10 megabits per second, 10BASE-T), Fast Ethernet LAN (100 megabits per second, 100BASE-TX) or Gigabit Ethernet LAN (1000 megabits per second, 1000BASE-T). Refer to Operating Basics, for details. Do not connect any cable other than a LAN cable to the LAN jack. It could cause damage or malfunction.
Battery pack The rechargeable lithium-ion battery pack provides power to the computer when the AC adaptor is not connected. For more detailed information on the use and operation of the battery pack please refer to the Battery section. Underside The following figures show the underside of the computer. You should ensure that the display is closed before the computer is turned over to avoid causing any damage. Figure 3-5 The underside of the computer 1 3 4 2 6 5 1. Battery lock 2.
Only the TOSHIBA Hi-Speed Port Replicator III 180W is applicable with this Docking port for TECRA W50-A series. Only the TOSHIBA Hi-Speed Port Replicator III 180W or 120W is applicable with this Docking port for TECRA A50-A/Satellite PRO A50A series. Do not attempt to use any other Port Replicator. Keep foreign objects out of the docking port. A pin or similar object can damage the computer's circuitry. Memory module slot cover The slot A and slot B memory module is located here.
Figure 3-6 The front of the computer with the display panel open 3 1 4 2 2 5 6 10 6 16 12 11 13 15 14 7 13 8 9 9 A 1. Wireless communication antennas (not shown)* 2. Microphone* 3. Web Camera LED* 4. Web Camera* 5. Display screen 6. Display hinges 7. Touch Pad ON/OFF indicator* 8. eco indicator 7 8 9 9 B 9. Touch Pad control buttons 10. Power button 11. Keyboard 12. Touch Pad 13. AccuPoint control button* 14. AccuPoint * 15. Middle button* 16.
Microphone The built-in microphone allows you to import and record sounds for your application - please refer to the Sound System and Video mode section for more information. Web Camera LED The Web Camera LED glows when the Web Camera is operating. Web Camera Web Camera is a device that allows you to record video or take photographs with your computer. You can use it for video chatting or video conferences using a communication tool. Some models are equipped with a Web Camera.
eco indicator Double tap this indicator to launch the TOSHIBA eco Utility. Touch Pad control buttons The two buttons below the Touch Pad are used like the buttons on a standard mouse - press the left button to select a menu item or to manipulate text or graphics designated by the pointer, and press the right button to display a menu or other function depending on the software you are using. Power button Press this button to turn the computer's power on or off.
NFC (Near Field Communication) detection area NFC (Near Field Communication) initiates interactions immediately between people and objects close the computer. NFC enables quick ad-hoc connections from PC to PC, or PC to device, through simple physical touch, without the pre-requisite of formal pairing. The interactions are intended to be quick, simple and delightful, simplifying the interactions with daily used devices and promoting a more social computing experience.
Under certain unusual conditions of prolonged non-use and/or exposure to high temperatures, the SSD may be vulnerable to data retention errors. Legal Footnote (HDD/SSD Capacity) For more information regarding HDD/SSD Capacity, please refer to the Legal Footnotes section. RTC battery The internal RTC battery backs up the Real Time Clock (RTC) and calendar. Video RAM The memory in a computer's graphics adaptor, used to store the image displayed on a bitmap display.
sustained battery life. Switching is automatic and does not require the user to reboot the computer. In the Manage 3D Settings menu of NVIDIA Control Panel, you can change the global 3D settings and create overrides for specific programs. The overrides will be used automatically each time the specified programs are launched. Please use the default setting for NVIDIA Optimus technology. If the program does not run normally after the setting has been changed, please restore the program to the default setting.
The Display Power Saving Technology feature can be disabled in the Intel® HD Graphics Control Panel/Intel® Graphics and Media Control Panel. You can access this control panel in the following way: Right-click on the desktop and click Graphics Properties... In Intel® HD Graphics Control Panel: 1. 2. 3. Click Power and select On battery. Click Off under Display Power Saving Technology. Click Apply.
When Intel® Rapid Start Technology is enabled, Wake-up on LAN, Wake-up on USB or Wake-up from Sleep Mode automatically functions are not available when the computer has been switched from Sleep Mode to Hibernation Mode. The partition allocation on the Solid State Drive for the Intel® Rapid Start Technology cannot be deleted even if Intel® Rapid Start Technology is disabled. Intel® Rapid Start Technology can only be used for Windows operating system.
Power on Power off (no operation) AC adaptor not connected Remaining battery capacity is above low battery trigger point • Operates Remaining battery capacity is below low battery trigger point • Operates Remaining battery capacity is exhausted Computer shuts down • LED: off • LED: flashes orange DC IN/Battery indicator Check the DC IN/Battery indicator to determine the status of the battery pack and the power status with the AC adaptor connected.
Power indicator Check the Power indicator to determine the power status of the computer the following indicator conditions should be noted: User's Manual Green Indicates power is being supplied to the computer and the computer is turned on. Flashing Orange Indicates that the computer is in Sleep Mode and that there is sufficient power available (AC adaptor or battery) to maintain this condition. No light Under any other conditions, the indicator does not light.
Chapter 4 Operating Basics This chapter describes the basic operations of your computer, and highlights the precautions that should be taken when using it. Using the Touch Pad The Touch Pad located in the palm rest may support the following gestures: Tap Tap once on the Touch Pad to activate an item, such as an app. Two-Finger Tap Tap once on the Touch Pad with two fingers together to display a menu or other function depending on the software you are using.
Some of the Touch Pad operations described in this section are only supported in certain applications. The Keyboard The number of keys available on your keyboard will depend on which country/region your computer is configured for, with keyboards being available for numerous languages. There are different types of keys, specifically typewriter keys, function keys, soft keys, Windows special keys and the keypad overlay. Never remove the key caps on your keyboard.
Function keys let you enable or disable certain features of the computer. The functions can be performed by pressing the associated function keys. Mute Pressing FN + ESC turns the volume on and off. Lock Pressing FN + F1 enters ''Lock computer mode''. To restore your desktop, you need to log on again. Power Plan Pressing FN + F2 changes the power settings. Sleep Pressing FN + F3 switches the system to Sleep Mode. Hibernate Pressing FN + F4 switches the system to Hibernation Mode.
Volume up Pressing FN + 4 increases the volume in increment. Some features will show the toast notification at the edges of the screen. Those toast notifications are disabled at factory default. You can enable them in the TOSHIBA Function Key application. To access it, click Desktop -> Desktop Assist -> Tools & Utilities -> Function Key.
Replacing the cap The AccuPoint cap is an expendable item that should be replaced after prolonged use. The spare AccuPoint cap is supplied with some models. 1. To remove the AccuPoint cap, firmly pinch the cap and pull it straight up. Figure 4-2 Removing the AccuPoint cap 1 1. AccuPoint cap Product appearance depends on the model you purchased. 2. Position a new cap on the peg and press it into place. The peg is square, so be careful to align the cap’s square hole with the peg.
becomes visible. In performing this process, you should also take care to ensure that the center of your fingerprint is on the sensor. The following illustrations show the recommended way to swipe your finger over the fingerprint sensor. Figure 4-3 Swipe the finger 1 1 1. Sensor Avoid swiping with your finger stiff or pressed too hard onto the sensor, and take care to ensure that the center of the fingerprint is touching the sensor before swiping.
Wash and dry your hands thoroughly. Remove static electricity from your fingers by touching any metal surface. Static electricity is a common cause of sensor failures, especially when the weather is dry. Clean the sensor with a lint-free cloth - do not use detergent or any other chemicals to clean the sensor.
Fingerprint utility limitations TOSHIBA does not guarantee that the fingerprint utility technology will be completely secure or error-free, or that it will accurately screen out unauthorized users at all times. TOSHIBA is not liable for any failure or damage that might arise out of the use of the fingerprint software. The fingerprint sensor compares and analyzes the unique characteristics in a fingerprint.
It is strongly recommended that you register 2 or more fingerprints. You cannot enroll the same fingerprint more than once, even on a different user account. Delete the Fingerprint Data Saved fingerprint data is stored in special non-volatile memory inside the fingerprint sensor. Therefore, if you give the computer to someone else, or dispose of it in any way, the following process is recommended to delete your fingerprint information: Delete the fingerprint data for the currently logged in user 1. 2. 3.
This is useful especially when many users are using the PCs, as user selection can be skipped. Fingerprint Authentication Procedure 1. 2. Start up the computer. The Logon Authorization screen is displayed. Choose any of the enrolled fingers and swipe the fingerprint on the sensor. If authentication is successful, the user will be logged on to Windows. If the fingerprint authentication fails, please logon using the Windows logon password.
It is necessary to register the User/BIOS Password and Windows Logon Password before using the Fingerprint Pre-Boot authentication and this Fingerprint Single Sign-On Feature. Please use the TOSHIBA Password Utility to register your User/BIOS Password. If Windows Logon is not the default for your system, see Manual to register your Windows Logon Password.
DVD Super Multi drive The drive supports the following formats: CD-ROM, DVD-ROM, DVDVideo, CD-DA, CD-Text, Photo CD™ (single/multi-session), CD-ROM Mode 1/Mode 2, CD-ROM XA Mode 2 (Form1, Form2), Enhanced CD (CDEXTRA), Addressing Method 2, DVD-R, DVD-RW, DVD+R, DVD+RW, DVD-RAM, DVD-R DL (Format1), DVD+R DL.
3. Lay the disc, label side up, in the disc tray. Figure 4-5 Inserting a disc 1 1. Laser lens When the disc tray is fully opened, the edge of the computer will cover the disc tray slightly. Therefore, you will need to turn the disc at an angle when you place it in the disc tray. After seating the disc, however, make sure it lies flat. Do not touch the laser lens or any portion of its surrounding casing as this could cause misalignment. Prevent foreign objects from entering the drive.
When the disc tray pops open slightly, wait a moment to make sure the disc has stopped spinning before pulling the disc tray fully open. 2. 3. The disc extends slightly over the sides of the disc tray so you can grasp it. Gently lift out the disc. Push the center of the disc tray to close it. Press gently until it locks into place. How to remove disc when the disc tray will not open Pressing the eject button will not open the disc tray when the computer power is off.
Blu-ray™ discs BD-R, BD-R DL discs can be written only once. The recorded data cannot be erased or changed. BD-RE, BD-RE DL discs can be recorded more than once. Writing discs You can use the DVD Super Multi drive to write data to either CD-R, CDRW, DVD-R, DVD-R DL, DVD-RW, DVD+R, DVD+R DL, DVD+RW or DVD-RAM discs.
Before writing or rewriting Based on TOSHIBA's limited compatibility testing, we suggest the following manufacturers of disc media, however, it must be noted that disc quality can affect write or rewrite success rates. Please also be aware that in no event does TOSHIBA guarantee the operation, quality or performance of any disc. CD-R: TAIYO YUDEN CO., Ltd. MITSUBISHI KAGAKU MEDIA CO., LTD. CD-RW: (Multi-Speed, High-Speed and Ultra-Speed) MITSUBISHI KAGAKU MEDIA CO., LTD.
BD-RE: Panasonic Corporation BD-RE DL: Panasonic Corporation BD-R TL: TDK. SHARP BD-RE TL: Panasonic Corporation Some types and formats of DVD-R DL and DVD+R DL discs may be unreadable. Disc created in DVD-R DL format4 (Layer Jump Recording) cannot be read.
Set the computer on a level surface and avoid places subject to vibration such as airplanes, trains or cars. In addition, do not use the computer on an unstable surface such as a stand. Keep mobile phones and other wireless communication devices away from the computer. TOSHIBA VIDEO PLAYER TOSHIBA VIDEO PLAYER is only provided with some models. Please be aware of the following limitations when you use the TOSHIBA VIDEO PLAYER: Notes on use This software can only be used on Windows operating system.
The TOSHIBA VIDEO PLAYER does not have a parental control function. In order to protect copyrights, the Windows Print Screen function is disabled when TOSHIBA VIDEO PLAYER is running. (Print Screen functions are disabled even when running other applications besides TOSHIBA VIDEO PLAYER and when TOSHIBA VIDEO PLAYER is minimized.) Please close the TOSHIBA VIDEO PLAYER to use the Print Screen function.
Operating TOSHIBA VIDEO PLAYER Notes on Using TOSHIBA VIDEO PLAYER. Screen display and available features may vary amongst videos and scenes. If the menu is opened in the Display Area using the Control window's Top Menu or Menu buttons, Touch Pad and mouse menu operations may not be able to be used. Open TOSHIBA VIDEO PLAYER Manual TOSHIBA VIDEO PLAYER features and instructions are explained in details in TOSHIBA VIDEO PLAYER Manual. Use the following procedure to open TOSHIBA VIDEO PLAYER Manual.
Do not playback video while recording television programs using other applications. Doing so may cause video playback or television program recording errors. In addition, if pre-scheduled recording starts during video playback it may cause video playback or television program recording errors. Please view video during times when there is no recording prescheduled. While playing a BD-J title, keyboard shortcut is ineffective. Resume play function cannot be used with some discs on TOSHIBA Blu-ray Disc Player.
Screen display and available features may vary amongst Blu-ray™ Videos and scenes. If the menu is opened in the Display Area using the Control window's Top Menu or Menu buttons, Touch Pad and mouse menu operations may not be able to be used. Open TOSHIBA Blu-ray Disc Player Manual TOSHIBA Blu-ray Disc Player features and instructions are explained in details in TOSHIBA Blu-ray Disc Player Manual. Use the following procedure to open TOSHIBA Blu-ray Disc Player Manual.
The computer's RTC battery is rechargeable and should be replaced only by your dealer or by a TOSHIBA service representative. The battery can explode if not properly replaced, used, handled or disposed. Dispose of the battery as required by local ordinances or regulations. Care and use of the battery pack This section provides the important safety precautions in order to handle your battery pack properly.
Procedures To recharge a battery pack, connect the AC adaptor to the DC IN 19V jack and plug the other end into a working outlet - the DC IN/Battery indicator will glow orange while the battery is being charged. Use only the computer connected to an AC power source or optional TOSHIBA Battery charger to charge the battery pack. Never attempt to charge the battery pack with any other charger. Charging Time The following table shows the approximate time required to fully charge a discharged battery.
The battery is nearly completely discharged. In this instance you should leave the AC adaptor connected for a few minutes and the battery should begin charging. The DC IN/Battery indicator may show a rapid decrease in battery operating time when you try to charge a battery under the following conditions: The battery has not been used for a long time. The battery has completely discharged and been left in the computer for a long time. In such cases you should follow the steps as detailed below: 1. 2. 3.
Hard Disk Drive power off period How often and for how long you use the HDD/SSD and external disk drives, for example, optical disc. How much charge the battery contained to begin with. How you use optional devices, such as a USB device, to which the battery supplies power. Whether you enable Sleep Mode, which can conserve battery power if you are frequently turning the computer off and on. Where you store your programs and data.
2. Disconnect the AC adaptor and turn on the computer's power - if it does not turn on then go to Step 4. 3. Operate the computer on battery power for five minutes. If you find that the battery pack has at least five minutes of operating time, continue operating until the battery pack is fully discharged, however, if the DC IN/Battery indicator flashes or there is some other warning to indicate a low battery condition, go to Step 4. 4.
3. 4. 5. 6. Remove all cables and peripherals that are connected to the computer. Close the display panel and turn the computer upside down. Slide the battery lock into its unlocked ( ) position. Slide and hold the battery release latch to disengage the battery pack and then lift it up to remove it from the computer. Figure 4-7 Releasing the battery pack 3 1 2 3 1 1. Battery lock 2. Battery release latch 2 3.
Installing a SIM Card To install a SIM card, follow the steps as detailed below: 1. 2. 3. 4. 5. 6. Click Power in the Settings charm, and then click Shut down while holding down the SHIFT key - ensure that the Power indicator is off Disconnect the AC adaptor, all cables, and any peripheral connected to the computer. Close the display panel. Turn the computer upside down and remove the battery pack (refer to Replacing the battery pack section, if required). Locate the SIM card slot.
6. Press the SIM Card gently and release it. It pops out of the slot. Figure 4-9 Removing the SIM Card 1 1. SIM Card Product appearance depends on the model you purchased. 7. 8. Grasp the SIM Card and remove it. Install the battery pack and turn your computer over. LAN The computer may have built-in support for Ethernet LAN (10 megabits per second, 10BASE-T), Fast Ethernet LAN (100 megabits per second, 100BASE-TX) or Gigabit Ethernet LAN (1000 megabits per second, 1000BASE-T).
If you are using Fast Ethernet LAN (100 megabits per second, 100BASETX), be sure to connect with a CAT5 cable or higher. You cannot use a CAT3 cable. If you are using Ethernet LAN (10 megabits per second, 10BASE-T), you can connect with a CAT3 or higher cable. Connecting the LAN cable To connect the LAN cable, follow the steps as detailed below: Connect the AC adaptor before connecting the LAN cable. The AC adaptor must remain connected during LAN use.
You should place a mat beneath the computer in order to prevent the computer's lid from becoming scratched or damaged when you are installing/replacing the memory module. In this instance you should avoid mats that are made of materials that hold or generate static electricity. When installing or removing a memory module, you must ensure that you do not touch any other internal areas of the computer. Use only memory modules approved by TOSHIBA.
6. Slide your fingernail or a thin object under the cover and lift it off. Figure 4-11 Removing the memory module cover 1 2 1 1. Screw 2. Memory module cover Product appearance depends on the model you purchased. 7. Follow this procedure to install or remove a memory module: Install procedure: Align the notch of the memory module with that of the memory slot and gently insert the module into the slot at about a 30 degree angle before holding it down until the latches on either side snap into place.
Figure 4-12 Seating the memory module 1 3 2 1 3 2 2 1 3 1. Notch 2. Slot B 3. Slot A Product appearance depends on the model you purchased. Never allow metal objects, such as screws, staples and paper clips, to enter the computer. Foreign metal objects can create a short circuit, which can cause computer damage and fire, possibly resulting in serious injury. Do not touch the connectors on the memory module or on the computer. Debris on the connectors may cause memory access problems.
Please also ensure that you hold the memory module along its left and right hand edges - the edges with the grooves in. Remove procedure: Push the latches away from the module in order to release it - a spring will force one end of the module up at an angle. And then grasp the module by its edges and remove it from the computer. Never allow metal objects, such as screws, staples and paper clips, to enter the computer.
Figure 4-13 Removing the memory module 1 2 1 1 1 1 2 1 1. Latches 2. Memory module Product appearance depends on the model you purchased. 8. Seat the memory module cover in place and secure it with the screw. Take care to ensure that the memory module cover is firmly closed. Figure 4-14 Seating the memory module cover 2 2 1 1. Memory module cover 2. Screw Product appearance depends on the model you purchased.
9. Install the battery pack - refer to Replacing the battery pack section, if required. 10. Turn your computer over. 11. Turn the computer on and make sure the available memory is recognized - to confirmed it, click Desktop -> Desktop Assist -> Control Panel -> System and Security -> System. Installing/Removing a memory module (Slot C/D) To install/remove a memory module (Slot C/D), follow the steps as detailed below: 1. 2. 3. 4. 5.
7. Slip your fingernail or a thin object under the notch at the end of the keyboard brace and lift it up to release latches and remove the keyboard brace. Figure 4-16 Removing the Keyboard brace 1 1. keyboard brace Product appearance depends on the model you purchased. 8. Lift the top edge of the keyboard while releasing the latches, rotate it and lay it face down on the palm rest. Never allow metal objects, such as screws, staples and paper clips, to enter the computer or keyboard.
9. Loosen the screw securing the memory module cover in place please note that the screw is attached to the cover in order to prevent it from being lost. Figure 4-17 Removing the memory module cover (1) 1 2 1. screw 2. Memory module cover Product appearance depends on the model you purchased. 10. Removing the memory module slot C/D cover. Figure 4-18 Removing the memory module cover (2) 1 1. Memory module cover Product appearance depends on the model you purchased. 11.
Figure 4-19 Installing the memory module 1 1 3 2 1. Notch 2. Slot C 3. Slot D Product appearance depends on the model you purchased. Never allow metal objects, such as screws, staples and paper clips, to enter the computer. Foreign metal objects can create a short circuit, which can cause computer damage and fire, possibly resulting in serious injury. Do not touch the connectors on the memory module or on the computer. Debris on the connectors may cause memory access problems.
Figure 4-20 Removing the memory module 1 1 1 1 1. Latches Product appearance depends on the model you purchased. Never allow metal objects, such as screws, staples and paper clips, to enter the computer. Foreign metal objects can create a short circuit, which can cause computer damage and fire, possibly resulting in serious injury. Do not touch the connectors on the memory module or on the computer. Debris on the connectors may cause memory access problems.
15. Close the display panel and turn the computer upside down. 16. Secure the KB screw on the underside of the computer. 17. Install the battery pack - refer to Replacing the battery pack section, if required. 18. Turn your computer over. 19. Turn the computer on and make sure the available memory is recognized - to confirmed it, click Desktop -> Desktop Assist -> Control Panel -> System and Security -> System.
protected material on another computer or other device, and you may not reproduce any copyrighted material except for your personal enjoyment. Below is a simple explanation for distinguishing SD memory cards from SDHC memory cards and SDXC memory cards. SD, SDHC and SDXC memory cards appear the same externally. However, the logo on memory cards is different, so pay careful attention to the logo when purchasing. The SD memory card logo is ( ). The SDHC memory card logo is ( ).
Set the write-protect switch to the lock position, if you do not want to record data. Memory cards have a limited lifespan, so it is important to backup important data. Do not write to a card if the battery power is low. Low power could affect writing accuracy. Do not remove a card while read/write is in progress. For more details on using memory cards, see manuals accompanying the cards. About the write-protect feature Memory media cards have a write-protect function.
Do not turn the computer off or switch to Sleep Mode or Hibernation Mode while files are being copied - doing so may cause data to be lost. Removing memory media The following instructions apply to all types of supported media devices. To remove memory media, follow the steps as detailed below: 1. 2. 3. Click the Desktop tile and open the Safely Remove Hardware and Eject Media icon on the Windows Taskbar. Select memory media. Grasp the media and remove it.
4. Press the ExpressCard gently to ensure a firm connection is made. Figure 4-23 Inserting the ExpressCard 1 2 1. ExpressCard slot 5. 2. ExpressCard After inserting the ExpressCard you should refer to its documentation and also check the configuration in Windows in order to ensure that it is correct. Removing an ExpressCard To remove an ExpressCard, follow the steps as detailed below. 1. 2. 3. 4. 5.
Inserting a Smart Card The Smart Card slot is located on the side of the computer. The Windows hot-install feature allows you to insert a Smart Card while the computer is turned on. To install a Smart Card, follow the steps as detailed below: 1. 2. Insert the Smart Card into the Smart Card slot with the metal connectors facing up. Press the Smart Card gently to ensure a firm connection is made. The computer will identify the Smart Card and display an icon in the Windows Taskbar.
As the port operation of all external monitors have not been confirmed, some monitors may not function properly. Connecting an external display Your computer comes with a built-in display, but you can also connect other external displays via available ports on the computer. External RGB monitor port An external analog monitor can be connected to the External RGB monitor port on the computer. To connect an external analog monitor, follow the steps as detailed below: 1.
2. 3. Plug the other end of the DisplayPort cable into the DisplayPort on your computer. Turn on the external monitor. The HDMI out port Some models are equipped with an HDMI out port. HDMI (High-Definition Multimedia Interface) port digitally transfers both video and audio data without reducing the quality. HDMI-compatible external display devices including televisions can be connected via the HDMI port.
Be sure to use the function key to select the display device before starting to play video. Do not change the display device while playing video. Do not change the display device under the following conditions. While data is being read or written. While communication is being carried out. Selecting HD Format To select the display mode, follow the steps as detailed below: 1. 2. 3. 4. 5. 6. 7. Click Desktop -> Desktop Assist -> Control Panel. Click Appearance and Personalization. Click Display.
You can also manually manage how the external displays will work and change the display settings by pressing P while holding down the ) key. If you disconnect the external display before you turn Windows ( the computer's power off, be sure to switch to the internal display. When you change the display output device, the audio playback device may not switch automatically.
2. Press down on the back of the computer until it clicks into place. The computer connector on the port replicator engages the computer’s docking port. When the computer is connected, the Docked light glows green. Figure 4-26 Aligning your computer with the Port Replicator 1 1. Docking port (computer) Make sure the AC adaptor is always connected to the TOSHIBA HiSpeed Port Replicator III 180W/120W while in use. Otherwise the Port Replicator will stop working, possibly resulting in data loss.
Mouse Printer To connect a Serial Device, follow the steps as detailed below: 1. 2. 3. Turn the computer’s power off. Remove the cap of the Serial port conversion cable. Connect the Serial port conversion cable to your computer. Figure 4-27 Connecting the Serial Connector 1 1. Serial Connector 2 2. Serial port conversion cable Security lock A security lock enables you to anchor your computer to a desk or other heavy object in order to help prevent unauthorized removal or theft.
Optional TOSHIBA Accessories You are able to add a number of options and accessories in order to make your computer even more powerful and convenient to use. For reference, the following list details some of the items that are available from your reseller or TOSHIBA dealer: Memory Kit DDR3 memory modules can easily be installed in the computer. The available option memory depends on TOSHIBA authorization.
3. On the Levels tab move the Microphone slider to increase or decrease the microphone volume level. If you feel the microphone volume level is inadequate, move the Microphone Boost slider to a higher level. Audio Enhancements In order to apply the sound effects for your current speaker, follow the steps below. 1. 2. 3. Click Desktop and right click on the Speakers icon on the Taskbar, and then select Playback devices from the sub menu. Select Speakers, and click Properties.
When you first launch the Realtek HD Audio Manager, you will see two device tabs. Speakers is the default output device. Microphone is the default input device. To change the default device, click the Set Default Device button under the chosen device tab. Information to view hardware information, software Click the Information button information, and language setting. Power Management The audio controller in your computer can be turned off when the audio function is not used.
Chapter 5 Utilities and Advanced Usage This chapter describes the utilities and special features of this computer, and the advanced usage of some utilities. Utilities and Applications This section describes the pre-installed utilities that come with the computer and details how to start them. For further information on their operation, you may refer to each utility's online manual, help files or README.TXT file (if applicable).
TOSHIBA Display Utility TOSHIBA Display Utility includes Desktop Text Size utility, Split Screen utility, Multiple Displays utility and other settings. Desktop Text Size allows you to make the text size bigger or smaller on the desktop according to your usage and favorite. You can change the text size on the display and on the title bar of windows by changing the scaling of the text size.
TOSHIBA Blu-ray Disc Player This software is provided for playback of Blu-ray Disc™. It has an on-screen interface and functions. To start this utility, click Desktop -> Desktop Assist -> Media & Entertainment -> TOSHIBA Blu-ray Disc Player. For details on how to use TOSHIBA Blu-ray Disc Player, see the help file. TOSHIBA eco Utility This computer is equipped with "eco mode". This mode slightly lowers performance of some devices to reduce electric power consumption.
TOSHIBA Service Station This application allows your computer to automatically search for TOSHIBA software updates or other alerts from TOSHIBA that are specific to your computer system and its programs. When enabled, this application periodically transmits to our servers a limited amount of system information, which will be treated in strict accordance with the rules and regulations as well as applicable data protection law.
Trusted Platform Module (TPM) The TPM (Trusted Platform Module) is a security encryption device for the HDD/SSD. You can install TPM by clicking Infineon TPM Software Professional Package from Applications and Drivers list. You can launch TOSHIBA Setup Utility to change the TPM settings in the Security tab. Please refer to TOSHIBA Setup Utility section for details on how to launch TOSHIBA Setup Utility. You may not have all the software listed above depending on the model you purchased.
Intelligent power supply *1 A microprocessor in the computer's intelligent power supply detects the battery's charge, automatically calculates the remaining battery capacity and protects electronic components from abnormal conditions such as a voltage overload from the AC adaptor. This can be specified in the Power Options. Battery save mode *1 This feature lets you configure the computer in order to save battery power. This can be specified in the Power Options.
Heat dispersal *1 To protect against overheating, the processor is equipped with an internal temperature sensor which activates a cooling fan or lowers the processing speed if the computer's internal temperature rises to a certain level. You are able to select whether to control this temperature by either turning on the fan first, then if necessary lowering the processor speed, or by lowering the processor speed first, then if necessary turning on the fan.
When entering the character string to register the password, enter from the keyboard character by character and do not enter as ASCII code or copy-and-paste the character string. In addition, ensure that the registered password is correct by outputting the character string to the password file. When entering a password, do not enter any characters (for example "!" or "#") produced by pressing the SHIFT or ALT keys. Delete (button) Click this button to delete a registered password.
Register or delete the Supervisor Password. Specify restrictions for general users. Starting the computer using a password If you have already registered a user password, there is one way to start the computer: Enter the password manually. The password is necessary only if the computer was shut down in Hibernation mode or boot mode. It is not needed in Sleep mode and Restart. To enter a password manually, follow the steps as detailed below: 1. Turn on the power as described in the Getting Started section.
Some options shown in grey are possible to confirm their status. TOSHIBA System Settings screen may have the following tabs: General—Allows you to view the current BIOS version or change certain settings back to their default values Sleep and Charge/Sleep Utilities—Allows you to set advanced features for sleep mode, hibernate mode, and shutdown state HDD Protection—Allows you to set the HDD Protection options.
compatible port even when the computer is turned OFF. "Power OFF" includes Sleep Mode, Hibernation Mode or shutdown state. To set USB Sleep and Charge feature, click Desktop -> Desktop Assist > Tools & Utilities -> System Settings -> Sleep and Charge/Sleep Utilities. Move the slider to enable or disable the Sleep and Charge function. The Sleep and Charge function may not work with certain external devices even if they are compliant with the USB specification.
Auto Mode (Default) is suitable for a wide range of digital audio players. While using Auto Mode, your computer can supply USB bus power at maximum 2.0A to the compatible ports while the computer is turned off. When USB device cannot be charged by Auto Mode, change to Alternate Mode. This function may not be able to be used with some connected external devices even if the appropriate mode is selected. In this situation, disable and stop using this function. Some external devices cannot use Auto Mode.
cases, use a USB port without "USB Sleep and Charge function" or disable “System ON CDP Charge Mode”. It is recommended that AC adaptor be connected to the computer while supplying USB bus power (DC5V, 1.5A). When your computer battery capacity is too low to continue, "System ON CDP Charge Mode" may not work. In those cases, connect the AC adaptor and reboot the computer. Always use the USB cable that was included with your USB device.
Panel. Doing so will automatically delete all collected information from the HDD/SSD. The TOSHIBA PC Health Monitor software does not extend or modify TOSHIBA's obligations under its standard limited warranty in any way. TOSHIBA's standard limited warranty terms and limitations apply. Starting the TOSHIBA PC Health Monitor The TOSHIBA PC Health Monitor can be started by clicking Desktop -> Desktop Assist -> Support & Recovery -> PC Health Monitor.
Setting up HDD Protection You can change HDD Protection settings. To open the utility, click Desktop -> Desktop Assist -> Tools & Utilities > System Settings -> HDD Protection. The utility can also be started from the icon in the Taskbar or from the Control Panel. HDD Protection You can enable or disable HDD Protection by moving the slider to the right or left.
different detection levels for the computer depending on whether it runs with the AC power (desktop) or with batteries (handheld or mobile usage), the detection level automatically switches according to the power connection mode. Detection Level Amplification When the AC adaptor is disconnected, HDD Detection assumes that the computer will be carried and sets the detection level to the maximum for 10 seconds.
System Recovery There is a hidden partition allocated on the HDD/SSD for the System Recovery Options in the event of a problem. You can also create recovery media and restore the system. The following items will be described in this section: Creating Recovery Media Restoring the pre-installed software from your created Recovery Media Restoring the pre-installed software from the Recovery HDD/SSD Creating Recovery Media This section describes how to create Recovery Media.
Please note that some of the disc media may not be compatible with the optical disc drive connected to your computer. You should therefore verify the optical disc drive supports the blank media you have chosen before proceeding. USB Flash Memory will be formatted and all the data in the USB Flash Memory will be lost when proceeding. 2. 3. 4. 5. Turn on your computer and allow it to load the Windows operating system from the HDD/SSD as normal.
3. 4. 5. Hold down the F12 key and then release this key one second after the computer is power on. Use the up and down cursor key to select the appropriate option from the menu according to your actual recovery media. A menu will be displayed from which you should follow the on-screen instructions.
1. 2. 3. 4. Click the Settings charm and click Change PC settings. Click General under PC settings. Scroll down to Remove everything and reinstall Windows and click Get started. Follow the on screen instructions to finish the recovery. Ordering Recovery Discs from TOSHIBA* You can order Product Recovery discs for your notebook from the TOSHIBA Europe Backup Media Online Shop. * Please note that this service is not free-of-charge. 1. 2. User's Manual Visit https://backupmedia.toshiba.eu on the Internet.
Chapter 6 Troubleshooting TOSHIBA has designed this computer for durability, however, should problems occur you are able to use the procedures detailed in this chapter to help determine the cause. All users should become familiar with this chapter as knowing what might go wrong can help prevent problems from occurring in the first place.
Check all cables to ensure they are correctly and firmly attached to the computer - loose cables can cause signal errors. Inspect all connecting cables for loose wires and all connectors for loose pins. Check that your disc media is correctly loaded Always try to make detailed notes of your observations and keep them in a permanent error log - this will help you to describe your problems to TOSHIBA Support. In addition, if a problem recurs, the log you have made will help to identify the problem faster.
Hardware If you cannot find a software problem, you should then check the setup and configuration of your hardware. First run through the items in the preliminary checklist as described previously then, if you still cannot correct the problem, try to identify the source - the next section provides checklists for individual components and peripherals.
If the indicator is glowing, the computer is on. Also, try turning the computer off and then on. If you are using an AC adaptor, verify that the computer is receiving power from the external power source by looking at the DC IN/Battery indicator. If the indicator is glowing, the computer is connected to a live external power source. The computer will not load advanced options during startup By holding down one of the following keys during startup, your computer will load advanced options as shown below.
Overheating power down If the processor's temperature reaches an unacceptably high level with either setting, the computer will automatically shut down to prevent any damage - in this instance all unsaved data in memory will be lost. Problem Procedure Computer shuts down automatically. Leave the computer off until the it reaches room temperature. If the computer has reached room temperature and it still does not start, or if it starts but shuts down quickly, contact TOSHIBA Support.
Problem Procedure Battery doesn’t If the battery is completely discharged, it will not charge when the AC begin charging immediately, in these instances you adaptor is attached. should wait a few minutes before trying again. If the battery still does not charge, you should check that the power outlet the AC adaptor is connected to its supplying power - this can be tested by plugging another appliance into it.
Real Time Clock Problem Procedure The BIOS setting and system date/ time are lost. The charge in the Real Time Clock (RTC) battery has run out - you will need to set the date and time in the TOSHIBA Setup Utility by using the following steps: 1. 2. 3. 4. 5. In the Settings charm, click Power and then select Restart. Hold down the F2 key and then release this key one second after the computer is power on - the TOSHIBA Setup Utility will load. Set the date in the System Date field.
Problem Procedure Markings appear on the computer's display panel. These marks may have come from contact with the keyboard and Touch Pad while the display panel has been closed. You should try to remove the marks by gently wiping the display panel with a clean dry cloth or, if this fails, with a good quality LCD screen cleaner. In this latter instance you should always follow the instructions with the screen cleaner and always ensure you let the display panel dry properly before closing it.
Problem Procedure You cannot access a Make sure the drive’s disc tray is securely closed. disc in the optical Press gently until it clicks into place. disc drive Open the disc tray and make sure the disc is properly seated. It should lie flat with the label facing up. A foreign object in the disc tray could block laser light from reading the disc. Make sure there is no obstruction. Remove any foreign object. Check whether the disc is dirty.
Problem Procedure On-screen pointer does not respond to pointing device operation In this instance the system might be busy - Try moving the mouse again after waiting a short while. Double-tapping (Touch Pad) does not work In this instance, you should initially try changing the double-click speed setting within the Mouse Control utility. 1. 2. 3. The on-screen pointer moves too fast or too slow In this instance, you should initially try changing the speed setting within the Mouse Control utility. 1.
Problem Procedure Double-clicking does In this instance, you should initially try changing not work the double-click speed setting within the Mouse Control utility. 1. 2. 3. The on-screen pointer moves too fast or too slow In this instance, you should initially try changing the speed setting within the Mouse Control utility. 1. 2. 3. The on-screen pointer moves erratically To access this utility, click Desktop -> Desktop Assist -> Control Panel -> Hardware and Sound -> Mouse.
Problem Procedure I cannot use the Sleep and Charge function Sleep and Charge function may be disabled. Enable the Sleep and Charge function in the TOSHIBA System Settings. When there is a current overflow of the external device connected to the compatible port, USB bus power (DC5V) supply may be stopped for safety reasons. When this happens, disconnect an external device if some external devices are connected. After that, turn the power of the computer ON/OFF to restore the function.
Problem Procedure The "USB WakeUp function" does not work. When "System ON CDP Charge Mode" or "USB Sleep and Charge function" is enabled, the "USB WakeUp" function does not work for ports that support the Sleep and Charge function. In that case, use an USB port that does not have the USB Sleep and Charge function or change to disable both "System ON CDP Charge Mode" and "USB Sleep and Charge function".
Problem Procedure Monitor does not turn on After confirming that the monitor's power switch is on, you should check the connections to make sure that the power cord/adaptor is firmly connected to the monitor and to a working power outlet. No display Try adjusting the contrast and brightness controls on the external monitor. Press the function key in order to change the display priority and ensure that it is not set for the internal display only. Check to see if the external monitor is connected.
Problem Procedure Wake-up on LAN does not work Make sure the AC adaptor is connected. The Wake-up on LAN function consumes power even when the system is off. If problems persist, consult your LAN administrator. Wireless LAN Problem Procedure Cannot access Wireless LAN Make sure the computer's Wireless communication function is on. If problems persist, contact your LAN administrator.
If a problem occurs when you are running software applications, consult the software documentation for troubleshooting suggestions and consider calling the software company's technical support department for assistance. Consult the reseller or dealer from where you purchased your computer and/or software - they are your best resource for current information and support.
Chapter 7 Appendix Specifications This section summarizes the computer’s technical specifications. Physical Dimensions Physical Dimensions shown below do not include parts that extend beyond the main body. The physical dimensions may vary depending on the model you purchased. Size Approximately 380.9 (w) x 253.9 (d) x 27.8/34.9 (h) millimeters (not including parts that extend beyond the main body).
External RGB monitor port pin assignment 5 1 15 11 10 6 Pin Signal Name Description I/O 1 CRV Red Video Signal O 2 CGV Green Video Signal O 3 CBV Blue Video Signal O 4 Reserved Reserved 5 GND Ground 6 GND Ground 7 GND Ground 8 GND Ground 9 +5V Power Supply 10 GND Ground 11 Reserved Reserved 12 SDA Data Signal I/O 13 HSYNC Horizontal Sync Signal O 14 VSYNC Vertical Sync Signal O 15 SCL Data Clock Signal O I/O (I): Input to computer I/O (O): Output
Certification agencies China: CQC U.S. and Canada: UL listed and CSA certified No. 18 AWG, Type SVT or SPT-2 Australia: AS Japan: DENANHO Europe: Austria: OVE Italy: IMQ Belgium: CEBEC The Netherlands: KEMA Denmark: DEMKO Norway: NEMKO Finland: FIMKO Sweden: SEMKO France: LCIE Switzerland: SEV Germany: VDE United Kingdom: BSI In Europe, two conductors power cord must be VDE type, H05VVH2-F or H03VVH2-F and for three conductors power cord must be VDE type, H05VV-F.
Australia Europe AS approved Approved by the appropriate agency Canada China CSA approved CCC approved Information for Wireless Devices Wireless Technology Interoperability The Wireless LAN is compatible with other LAN systems Direct Sequence Spread Spectrum (DSSS) /Orthogonal Frequency Division Multiplexing (OFDM) radio technology, and is compliant to: The IEEE 802.
Please visit http://www.pc.support.global.toshiba.com, if you have any questions about using Wireless LAN or Bluetooth Module. In Europe visit http://www.toshiba-europe.com/computers/tnt/bluetooth.htm Wireless Devices and your health Wireless products, like other radio devices, emit radio frequency electromagnetic energy. The level of energy emitted by Wireless products however is far much less than the electromagnetic energy emitted by wireless devices like for example mobile phones.
Always turn off wireless functionality if the computer is near automatic control equipment or appliances such as automatic doors or fire detectors. Radio waves can cause malfunction of such equipment, possibly resulting in serious injury. It may not be possible to make a network connection to a specified network name using the ad hoc network function. If this occurs, the new network (*) will have to be configured for all computers connected to the same network in order to re-enable network connections.
The range of the wireless signal is related to the transmit rate of the wireless communication. Communications at lower transmit range may travel larger distances. The range of your wireless devices can be affected when the antennas are placed near metal surfaces and solid high-density materials. Range is also impacted due to "obstacles" in the signal path of the radio that may either absorb or reflect the radio signal.
Europe Restrictions for Use of 2400.0-2483.5MHz Frequencies in Europe France: Outdoor use limited to 10mW e.i.r.p. within the band 2454-2483.5MHz Military Radiolocation use.Refarming of the 2.4GHz band has been ongoing in recent years to allow current relaxed regulation Full implementation planned 2012. Italy: - For private use, a general authorization is required if WAS/ RLAN’s are used outside own premises. For public use, a general authorization is required.
Russian Federation: Limited e.i.r.p 100mW. Permitted to use only for indoor applications, closed industrial and warehouse areas, and on board aircraft. 1. 2. Permitted to use for local networks of aircraft crew service communications on board aircraft in area of the airport and at all stages of flight. Permitted to use for public wireless access local networks on board aircraft during a flight at the altitude not less than 3000m.
check the current channel of operation. If operation is occurring outside of the allowable frequencies for outdoor use, as listed above, the user must contact the applicable national spectrum regulator to request a license for outdoor operation. Canada - Industry Canada (IC) This device complies with RSS-210 of the Industry Canada Rules.
The installer of this radio equipment must ensure that the antenna is located or pointed such that it does not emit RF field in excess of Health Canada limits for the general population; consult Safety Code 6, obtainable from Health Canada’s website www.hc-sc.gc.ca Caution: Radio Frequency Interference Requirements This device is restricted to indoor use due to its operation in the 5.15 to 5.25GHz frequency range. High-power radars are allocated as primary users (i.e. priority users) of the bands 5.
stations for mobile object identification systems (RFID) used in factory production lines (Other Radio Stations). 1. 2. 3. Before using this equipment, ensure that it does not interfere with any of the equipment listed above. If this equipment causes RF interference to other radio stations, promptly change the frequency being used, change the location of use, or turn off the source of emissions.
Device Authorization This device obtains the Technical Regulation Conformity Certification and it belongs to the device class of radio equipment of low-power data communication system radio station stipulated in the Telecommunications Business Law of Japan. Atheros WB222 802.11a/b/n Wireless LAN The Name of the radio equipment: WB222 DSP Research, Inc. Approval Number: D111398003 Intel® Centrino® Wireless-N 2230 Wireless LAN and Bluetooth The Name of the radio equipment: 2230BNHMW DSP Research, Inc.
Indonesia Ireland Italy Japan Korea Latvia Liechtenstein Lithuania Luxemburg Malta Monaco Netherlands Norway Philippines Poland Portugal Romania Slovak Republic Slovenia Spain Sweden Switzerland UK USA Legal Footnotes Non-applicable Icons Certain computer chassis are designed to accommodate all possible configurations for an entire product series.
performance, use your computer product only under recommended conditions. Read additional restrictions in your product documentation. Contact TOSHIBA technical service and support, refer to TOSHIBA support section for more information. 64-Bit Computing Certain 32-bit device drivers and/or applications may not be compatible with a 64-bit CPU/operating system and therefore may not function properly.
HDD/SSD Capacity 1 Gigabyte (GB) means 109 = 1,000,000,000 bytes using powers of 10. The computer operating system, however, reports storage capacity using powers of 2 for the definition of 1 GB = 230 = 1,073,741,824 bytes, and therefore shows less storage capacity. Available storage capacity will also be less if the product includes one or more pre-installed operating systems, such as Microsoft Operating System and/or pre-installed software applications, or media content.
Abbreviations User's Manual AC: Alternating Current AMT: Intel Active Management Technology ASCII: American Standard Code for Information Interchange BIOS: Basic Input/output System BD-ROM: Blu-ray Disc Read-only Memory bps: bits per second CD: Compact Disc CD-ROM: Compact Disc Read-only Memory CD-RW: Compact Disc-rewritable CMOS: Complementary Metal-oxide Semiconductor CPU: Central Processing Unit DC: Direct Current DDR: Double Data Rate DIMM: Dual Inline Memory Module DVD: D
User's Manual IEEE: Institute of Electrical and Electronics Engineers I/O: Input/Output IRQ: interrupt request ISP: Internet Service Provider KB: kilobyte LAN: Local Area Network LCD: Liquid Crystal Display LED: Light Emitting Diode MB: megabyte MBps: megabytes per second MMC: Multi Media Card OCR: Optical Character Recognition (Reader) PC: Personal Computer PCI: Peripheral Component Interconnect PCMCIA: Personal Computer Memory Card International Association RAM: Random Acce
Index A Documentation list 2-1 Dual Pointing Device AccuPoint 4-4 Touch Pad 6-9 AC adaptor additional 4-54 connecting 2-3 DC IN 19V jack 3-6 DVD Super Multi drive using writing B Battery extending life 4-26 monitoring capacity 4-25 real time clock 3-13, 4-22 save mode 5-6 types 4-22 E Equipment checklist 2-1 ExpressCard inserting 4-45 removing 4-46 Battery indicator External monitor problems 6-14 Battery pack replacing 4-27 Bluetooth 7-7 C FN + 1 ( reduce) 4-3 Cleaning the computer 1-17 FN + 2 (en
FN + F6 (Brightness Down) 4-3 removing 4-45 FN + F7 (Brightness Up) 4-3 Memory media slot 4-42 FN + F8 (Wireless) 4-3 Moving the computer 1-18 FN + F9 (Touch Pad) 4-3 MultiMediaCard removing 4-45 FN + space (Zoom) 4-3 FN + TAB (ODD) H Hard disk drive automatic power off 5-5 K Keyboard Function keys F1...
Power 6-4 Real Time Clock 6-7 Sleep and Charge function 6-11 Sound system 6-13 TOSHIBA support 6-15 Touch Pad 6-9 USB device 6-11 USB mouse 6-10 R T TOSHIBA Desktop Assist 5-1 U USB device problems 6-11 V Recovery hard disk drive 5-19 Video mode 4-56 Recovery Media 5-18, 5-20 Restarting the computer 2-9 S Video RAM 3-13 W Web Camera 3-10 SD/SDHC/SDXC Card formatting 4-43 note 4-42 Wireless communication 7-5 Security lock 4-53 Sleep and Charge function problems 6-11 Sleep Mode setting 2-9 System
