Toshiba Personal Computer Satellite/Satellite PRO Maintenance Manual TOSHIBA CORPORATION [CONFIDENTIAL]
Copyright © 2010 by Toshiba Corporation. All rights reserved. Under the copyright laws, this manual cannot be reproduced in any form without the prior written permission of Toshiba. No patent liability is assumed with respect to the use of the information contained herein. Toshiba Personal Computer STREAMLINE-M 10 SERIES MAINTENANCE MANUAL Maintenance Manual First edition April, 2010 Disclaimer The information presented in this manual has been reviewed and validated for accuracy.
Preface This maintenance manual describes how to perform hardware service maintenance for the Toshiba Personal Computer STREAMLINE-M 10 SERIES MAINTENANCE MANUAL, referred to as the STREAMLINE-M 10 SERIES MAINTENANCE MANUAL Series in this manual. The procedures described in this manual are intended to help service technicians isolate faulty Field Replaceable Units (FRUs) and replace them in the field.
The manual is divided into the following parts: Chapter 1 Hardware Overview describes the STREAMLINE-M 10 SERIES MAINTENANCE MANUAL Series system unit and each FRU. Chapter 2 Troubleshooting Procedures explains how to diagnose and resolve FRU problems. Chapter 3 Test and Diagnostics describes how to perform test and diagnostic operations for maintenance service. Chapter 4 Replacement Procedures describes the removal and replacement of the FRUs.
Some operations require you to simultaneously use two or more keys. We identify such operations by the key top symbols separated by a plus (+) sign. For example, Ctrl + Pause (Break) means you must hold down Ctrl and at the same time press Pause (Break). If three keys are used, hold down the first two and at the same time press the third.
Table of Contents Chapter 1 1.1 Features ....................................................................... Fehler! Textmarke nicht definiert. 1.2 2.5-inch HDD.............................................................. Fehler! Textmarke nicht definiert. 1.3 Power Supply .............................................................. Fehler! Textmarke nicht definiert. 1.4 Batteries ...................................................................... Fehler! Textmarke nicht definiert. 1.4.
Chapter 3 3.1 The Diagnostic Test .............................................................................................................. 3 3.2 Executing the Diagnostic Test ............................................................................................. 4 3.3 Display Configuration ........................................................................................................ 7 3.4 Audio sound Test ..........................................................................
4.1 General ........................................................................ Fehler! Textmarke nicht definiert. Safety Precautions ....................................................... Fehler! Textmarke nicht definiert. Before You Begin ....................................................... Fehler! Textmarke nicht definiert. Disassembly Procedures ............................................. Fehler! Textmarke nicht definiert. Assembly Procedures .................................................
Removing the RGB Board .......................................... Fehler! Textmarke nicht definiert. Installing the RGB Board ........................................... Fehler! Textmarke nicht definiert. 4.10 WLAN Card................................................................ Fehler! Textmarke nicht definiert. Removing the WLAN Card ........................................ Fehler! Textmarke nicht definiert. Installing the WLAN Card ..........................................
4.20 Motherboard................................................................ Fehler! Textmarke nicht definiert. Removing the Motherboard ........................................ Fehler! Textmarke nicht definiert. Installing the Motherboard .......................................... Fehler! Textmarke nicht definiert. 4.21 Thermal Module ......................................................... Fehler! Textmarke nicht definiert. Removing the Thermal Module ..................................
Figure 2-9 Camera troubleshooting process ............................................................................... 27 Figure 2-10 Bluetooth troubleshooting process .......................................................................... 29 Figure 2-11 2 in 1 card troubleshooting process ......................................................................... 31 Figure 2-12 HDD troubleshooting process ..................................................................................
Figure 4.22 Removing the minicard brackets ....................... Fehler! Textmarke nicht definiert. Figure 4.23 Removing the display assembly ........................ Fehler! Textmarke nicht definiert. Figure 4.24 Removing the USB & Audio Board .................. Fehler! Textmarke nicht definiert. Figure 4.25 Disconnect the FFC and remove two screws .... Fehler! Textmarke nicht definiert. Figure 4.26 Removing the HDD Board ................................ Fehler! Textmarke nicht definiert. Figure 4.
Appendix D Keyboard Scan/Character Codes ......................................................................... D-1 Appendix E Key Layout ............................................................................................................ E-1 Appendix F Series Screw Torque List ....................................................................................... F-1 Appendix G Reliability ...........................................................................................................
Chapter 1 Hardware Overview
1 Hardware Overview Chapter 1 Contents 1.1 Features .................................................................................................................. 1-1 1.2 2.5-inch HDD ....................................................................................................... 1-10 1.3 Power Supply ....................................................................................................... 1-11 1.4 Batteries .................................................................
1 Hardware Overview Figures Figure 1-1A ID Parts Description Placement Part A.......................................................... 1-6 Figure 1-2 SATA HDD ................................................................................................. 1-10 Tables Table 1-1 HDD Specifications ..................................................................................... 1-10 Table 1-2 Quick/Normal Charging Time .....................................................................
Fehler! Verwenden Sie die Registerkarte 'Start', um 標題 2 dem Text zuzuweisen, der hier angezeigt werden soll. Fehler! Verwenden Sie die Registerkarte 'Start', um 標題 2 dem Text zuzuweisen, der hier angezeigt werden soll. 1 Hardware Overview 1.1 Features The Toshiba Satellite T230/T235/Pro T230/Pro T235/PORTEGE T230 is a small-size PC notebook equipped with a Dual Core Processor, providing high-speed processing capabilities and advanced features.
1 Hardware Overview Fehler! Verwenden Sie die Registerkarte 'Start', um 標題 2 dem Text zuzuweisen, der hier angezeigt werd Display The LCD display comes with the following: y 13.3" W (16:9) HD+ (1366x768) CSV LED Graphics (BTO) Intel® Arrandale Chipset for integrated graphics display Keyboard The computer is equipped with a Toshiba standard 300mm keyboard, which has 86/87 keys support without stick-point. It is a Win7-compliant keyboard with optional Windows keys and application keys.
Fehler! Verwenden Sie die Registerkarte 'Start', um 標題 2 dem Text zuzuweisen, der hier angezeigt werden soll. Fehler! Verwenden Sie die Registerkarte 'Start', um 標題 2 dem Text zuzuweisen, der hier angezeigt werden soll. 1 Hardware Overview Sound system The integrated sound system is composed of two Realtek Azalia internal speakers, an internal microphone (BTO with internal camera), and standard Microphone-IN and Headphone-OUT ports. Internal Camera (BTO) It supports 0.3M and 1.
1 Hardware Overview Fehler! Verwenden Sie die Registerkarte 'Start', um 標題 2 dem Text zuzuweisen, der hier angezeigt werd Broadcom 802.11 bgn/bg 4313 (WLAN/BT) w/Bluetooth V3.
Fehler! Verwenden Sie die Registerkarte 'Start', um 標題 2 dem Text zuzuweisen, der hier angezeigt werden soll. Fehler! Verwenden Sie die Registerkarte 'Start', um 標題 2 dem Text zuzuweisen, der hier angezeigt werden soll. 1 Hardware Overview 3G (BTO) The 3G module employs a PCI Express Mini Card. It enables computer users to have mobile access to the internet or to a corporate network.
1 Hardware Overview Fehler! Verwenden Sie die Registerkarte 'Start', um 標題 2 dem Text zuzuweisen, der hier angezeigt werd Figure 1-1A shows the computer and its system unit configuration.
Fehler! Verwenden Sie die Registerkarte 'Start', um 標題 2 dem Text zuzuweisen, der hier angezeigt werden soll. Fehler! Verwenden Sie die Registerkarte 'Start', um 標題 2 dem Text zuzuweisen, der hier angezeigt werden soll.
1 Hardware Overview Fehler! Verwenden Sie die Registerkarte 'Start', um 標題 2 dem Text zuzuweisen, der hier angezeigt werd The system unit of the computer consists of the following components: Processor (BTO) The computer is equipped with one of the following Intel® processors: Intel® Arrandale Processor Memory (BTO) The computer has two SODIMM slots which come standard with 1GB/2GB/4GB, accepting BTO for your memory requirements. It can incorporate up to 8 GB of main memory.
Fehler! Verwenden Sie die Registerkarte 'Start', um 標題 2 dem Text zuzuweisen, der hier angezeigt werden soll. Fehler! Verwenden Sie die Registerkarte 'Start', um 標題 2 dem Text zuzuweisen, der hier angezeigt werden soll.
1 Hardware Overview Fehler! Verwenden Sie die Registerkarte 'Start', um 標題 2 dem Text zuzuweisen, der hier angezeigt werd 1.2 2.5-inch HDD The computer contains an extremely low-profile and lightweight, high-performance HDD. The HDD incorporates a 9.5 mm magnetic disk and mini-Winchester type magnetic heads. The HDD interface conforms to Serial ATA. Storage capacities supported are 160, 250, 320, 500 and 640 GB. The HDD is shown in Figure 1-2 and some of its specifications are listed in Table 1-1.
Fehler! Verwenden Sie die Registerkarte 'Start', um 標題 2 dem Text zuzuweisen, der hier angezeigt werden soll. Fehler! Verwenden Sie die Registerkarte 'Start', um 標題 2 dem Text zuzuweisen, der hier angezeigt werden soll. 1 Hardware Overview 1.3 Power Supply The power supply unit provides constant voltage (19V) for the system board and performs the following functions: 1. Power input monitor y Checks whether the AC adapter (DC power supply) is connected to the computer.
1 Hardware Overview Fehler! Verwenden Sie die Registerkarte 'Start', um 標題 2 dem Text zuzuweisen, der hier angezeigt werd 6. Output monitor y Monitors the voltage output to the system block (load/logic circuit side). y Monitors the voltage, over-voltage, input/output current of the battery pack. y Monitors the internal temperature of the battery pack. y Monitors the supply voltage from the AC adapter.
Fehler! Verwenden Sie die Registerkarte 'Start', um 標題 2 dem Text zuzuweisen, der hier angezeigt werden soll. Fehler! Verwenden Sie die Registerkarte 'Start', um 標題 2 dem Text zuzuweisen, der hier angezeigt werden soll. 1 Hardware Overview 1.4 Batteries The computer has the following two types of batteries: Main Battery Pack Real Time Clock (RTC) Battery 1.4.1 Main Battery The main battery pack serves as the computer's main power source when the AC adapter is not attached.
1 Hardware Overview Fehler! Verwenden Sie die Registerkarte 'Start', um 標題 2 dem Text zuzuweisen, der hier angezeigt werd NOTE: The time required for normal charge depends on the power consumption by the system. Using a fluorescent lamp and frequently accessing the disk consumes more power and lengthens the charge time. Any of the following can stops battery charge: 1. The battery becomes fully charged. 2. The AC adapter or battery pack is removed. 3. The battery or AC adapter voltage is abnormal.
Chapter 2 Troubleshooting Procedures
2 Troubleshooting Procedures Chapter 2 Contents 2.1 Troubleshooting Introduction ......................................................................................2 2.2 Troubleshooting Flowchart ..........................................................................................3 2.3 Power Supply Troubleshooting ...................................................................................9 2.4 Display Troubleshooting .................................................................
2 Troubleshooting Procedures Figures Figure 2-1 Troubleshooting flowchart (1/2)……………………………………………….5 Figure 2-1 Troubleshooting flowchart (2/2)……………………………………………….6 Figure 2-2 Power Supply Troubleshooting Process……………………………………….9 Figure 2-3 Display troubleshooting process……………………………………………...14 Figure 2-4 Keyboard troubleshooting process……………………………………………17 Figure 2-5 External USB device troubleshooting process………………………………..19 Figure 2-6 TouchPad troubleshooting process…………………………………………...
2 Troubleshooting Procedures 1. Display 7. Wireless LAN 13. 4 in 1 card 2. HDD 8. Camera 14. CRT 3. Keyboard 9. Bluetooth 15. LAN 4. USB ports 10. Headphone 16. 3D sensor 5. Touchpad 11.MIC 17. HDMI 6. Speaker/Head 12. 3G 19. Wimax 18. E-SATA The Diagnostics Disk operations are described in Chapter 3. Detailed replacement procedures are given in Chapter 4. The following tools are necessary for implementing the troubleshooting procedures: 1. Phillips screwdriver (2 mm) 2.
2 Troubleshooting Procedures determining which troubleshooting procedures to execute. Before performing any troubleshooting procedures, verify the following: z Ask the user if a password is registered, if it is, ask him or her to enter the password. z Verify with the customer that Toshiba Windows XP/Win7/Linux is installed on the hard disk. Operating systems that were not preinstalled by Toshiba can cause the computer to malfunction. z Make sure all optional equipment is removed from the computer.
2 Troubleshooting Procedures STA RT C o n n e c t th e A C a d a p te r to th e D C IN s o c k e t Is th e D C -IN L E D o n ? No P e rfo rm th e P o w e r S u p p ly T ro u b le s h o o tin g p ro c e d u re s in s e c tio n 2 .3 Y es Is th e B a tte ry L E D o n ? No P e rfo rm th e P o w e r S u p p ly T ro u b le s h o o tin g p ro c e d u re s in s e c tio n 2 .3 No P e rfo rm th e P o w e r S u p p ly T ro u b le s h o o tin g p ro c e d u re s in s e c tio n 2 .
2 Troubleshooting Procedures A Does typed characters appear correctly? No Perform the Keyboard Troubleshooting procedures in section 2.5 No Perform the HDD Troubleshooting procedures in section 2.13 Yes After confirming which diagnostics test has detected an error, perform the appropriate procedure as outlined below. Yes Insert USB memory disk.
2 Troubleshooting Procedures If the diagnostics program cannot detect an error, the problem may be intermittent. The test program should be executed several times to isolate the problem. When a problem has been located, perform the appropriate troubleshooting procedures as follows: 1. If an error is detected by the battery test, perform the Power Supply Troubleshooting procedures in Section 2.3 2. If an error is detected by the display test, perform the Display Troubleshooting procedures in Section 2.4 3.
2 Troubleshooting Procedures Other problems that are not covered by the diagnostics program may be discovered by a user. 1. If an error is detected when using an external USB device, perform the external USB Devices Troubleshooting procedures in Section 2.6 2. If an error is detected when using the speakers, perform the Speaker Troubleshooting procedures in Section 2.8 3. If an error is detected when using the Wireless LAN, perform the Wireless LAN Troubleshooting procedures in Section 2.9 4.
2 Troubleshooting Procedures 2.
2 Troubleshooting Procedures as instructed. The flowchart in Figure 2-2 gives a summary of the process.
2 Troubleshooting Procedures Table 2-2 DC-IN LED DC-IN LED Power supply status Solid on AC power exists (LED is Green). Off No AC power exists. To check the power supply status, install a battery pack and connect an AC adaptor to the DC-IN port on the computer and to a power supply. If the DC-IN LED or Battery LED is not lit, go to Procedure 2. Procedure 2 Adaptor / battery replacement A faulty adaptor may not supply power or may not charge the battery. Perform Check 1.
2 Troubleshooting Procedures Procedure 3 Power supply connection check The power supply wiring diagram is shown below: AC adaptor cord AC power cord AC adaptor System board Battery Any of the connectors may be disconnected. Perform Check 1. Check 1 Disconnect the AC power cord from wall outlet. Check the power cable for breaks. If the power cord is damaged, connect a new AC power cord. If there is no damage, go to Check 2.
2 Troubleshooting Procedures Procedure 4 Diagnostic check The power supply may not charge the battery pack. Perform the following procedures: 1. Reinstall the battery pack. 2. Attach the AC adaptor and turn on the power. If you cannot turn on the power, go to Procedure 5. 3. Run the Diagnostic test following the procedures described in Chapter 3, Tests and Diagnostics. If no problem is detected, the battery is functioning normally.
2 Troubleshooting Procedures 2.4 Display Troubleshooting STA RT P e r fo r m e x te r n a l d is p la y c h e c k (P r o c e d u re 1 ) D o e s th e e x te r n a l d is p la y f u n c tio n o k ? No P e r fo r m d ia g n o s tic c h e c k ( P ro c e d u r e 2 ) Y es W a s a d is p la y p ro b le m d e te c te d ? No D is p la y is n o t f a u lty . C o n tin u e tro u b le s h o o tin g re fe r to F ig u re 2 .
2 Troubleshooting Procedures This section describes how to determine if the computer’s display is functioning properly. The process is outlined in Figure 2-3. Start with Procedure 1 and continue with the other procedures as instructed. Procedure 1: External display check Procedure 2: Diagnostic check Procedure 3: Connector and replacement check Procedure 1 External display check Connect an external display to the computer’s external monitor port, and then boot the computer.
2 Troubleshooting Procedures Procedure 3 Connector and replacement check The LCD module and system board are connected to the display circuits. Any of these components may be damaged. Refer to Chapter 4, Replacement Procedures, for instructions on how to disassemble the computer and then perform the following checks: Check 1 Make sure the DDR module is seated properly. Test display again. If the problem still exits, replace the DDR RAM module. If the problem still exists, perform Check 2.
2 Troubleshooting Procedures 2.5 Keyboard Troubleshooting START P e r f o r m d ia g n o s tic c h e c k (P ro c e d u re 2 ) W a s a k e y b o a rd p r o b le m d e te c te d ? No K e y b o a r d is n o t f a u lty . C o n tin u e tr o u b le s h o o tin g - r e f e r to F ig u r e 2 .
2 Troubleshooting Procedures To determine if the computer’s keyboard is functioning properly, perform the following procedures. Figure 2-4 outlines the process. Start with Procedure 1 and continue with the other procedures as instructed. Procedure 1: Diagnostic check Procedure 2: Connector and replacement check Procedure 1 Diagnostic check Run the test and Diagnostics Program, which will automatically execute the Keyboard Test.
2 Troubleshooting Procedures 2.
2 Troubleshooting Procedures To determine if the computer’s external USB devices are functioning properly, perform the following procedures. Figure 2-5 outlines the process. Start with Procedure 1 and continue as instructed. Procedure 1: External device and connection check Procedure 2: Replace system board Procedure 1 External device and connection check The USB device may be damaged or the connection may be faulty. Use windows application to check device can work fine or not.
2 Troubleshooting Procedures 2.7 Touch pad Troubleshooting STA RT P e rfo rm T o u c h p a d check (P ro c e d u re 1 ) D oes T ouchpad fu n c tio n o k ? No P e rfo rm d ia g n o s tic check (P ro c e d u re 2 ) Y es W as a T ouchpad p ro b le m d e te c te d ? No T o u c h p a d is n o t fa u lty .
2 Troubleshooting Procedures To determine if the computer’s built-in TouchPad is functioning properly, perform the following procedures. Figure 2-6 outlines the process. Start with Procedure 1 and continue as instructed. Procedure 1: Perform Touchpad test Procedure 2: Touchpad connection check Procedure 3: Touchpad replacement check Procedure 1 Perform Touchpad test Run the Diagnostic Program, which will automatically execute the Touchpad test.
2 Troubleshooting Procedures 2.8 Speaker Troubleshooting START P e r f o r m a u d io s o u r c e te s t (P ro c ed u re 1 ) D o a ll s o u r c e s h a v e s a m e p r o b le m ? No S p e a k ers are n o t f a u lty .
2 Troubleshooting Procedures To determine if the computer’s built-in speakers are functioning properly, perform the following procedures. Figure 2-7 outlines the process. First adjust the speaker volume to an appropriate level. Start with Procedure 1 and continue as instructed. Procedure 1: Audio source test Procedure 2: Earphone test Procedure 3: Connection check Procedure 4: Replacement check Procedure 1 Audio source test Try different audio sources (e.g.
2 Troubleshooting Procedures 2.9 Wireless LAN Troubleshooting START Perform Wireless LAN connection check (Procedure 1) Was a wireless LAN problem delected? No Wireless LAN system is not faulty.
2 Troubleshooting Procedures The wireless LAN antenna wire, wireless LAN unit or system board may each be the source of a wireless LAN fault. Any of these components may be damaged. To determine if the computer’s wireless LAN system is functioning properly, perform the following procedures. Figure 2-8 outlines the process. Start with Procedure 1 and continue with the other procedures as instructed.
2 Troubleshooting Procedures 2.
2 Troubleshooting Procedures The Camera board or system board may be the reason of a Camera fault. Either of these two components may be damaged. To determine if the computer’s Camera is functioning properly, perform the following procedures. Figure 2-9 outlines the process. Start with Procedure 1 and continue with the other procedures as instructed.
2 Troubleshooting Procedures 2.
2 Troubleshooting Procedures The Bluetooth antenna wire, Bluetooth module or system board may be the reason of a Bluetooth fault. Any of these components may be damaged. To determine if the computer’s Bluetooth is functioning properly, perform the following procedures. Figure 2-10 outlines the process. Start with Procedure 1 and continue with the other procedures as instructed.
2 Troubleshooting Procedures 2.12 4in1 card Troubleshooting START Perform 4 in 1 CARD test (Procedure 1) Do errors occur during 4 IN 1 CARD test? No 4 IN 1 unit is not faulty. Yes Perform 4 IN 1 card socket replacement check (Procedure 2) Replace system board END Figure 2-11 4 in 1 card troubleshooting process This section describes how to determine if the 4 IN 1 Card is functioning properly. The process is summarized in Figure 2-11.
2 Troubleshooting Procedures Procedure 2: 4 in 1 card socket check Procedure 1 4 in 1card test The 4 in 1 Card test card contains a 4 in 1 card test program. Ensure the card in fully inserted into the socket before running the program. If an error occurs during the 4 in 1 card test, perform Procedure 2. If no error occurs, it is likely that the original 4 in 1 card was faulty.
2 Troubleshooting Procedures 2.
2 Troubleshooting Procedures The HDD or system board may be the reason of a HDD fault. Either of these two components may be damaged. To determine if the computer’s HDD is functioning properly, perform the following procedures. Figure 2-12 outlines the process. Start with Procedure 1 and continue with the other procedures as instructed.
2 Troubleshooting Procedures 2.
2 Troubleshooting Procedures Procedure 2: CRT set check Procedure 1 CRT connection check The CRT cable may be damaged or the connections may be loose. Perform Check 1: Check 1 Make sure CRT cable is firmly plugged into both the CRT set and the CRT port of the computer. If the cable is connected correctly, go to Check 2. Check 2 Make sure the CRT port is firmly secured to the system board of the computer. If the malfunction remains, go to Check 3. Check 3 The CRT cable may be damaged.
2 Troubleshooting Procedures 2.15 LAN Troubleshooting STA R T P e rfo rm d ia g n o s tic check (P ro ced u re 2 ) W as a L A N p ro b le m d e te c te d ? N o L A N is n o t fa u lty .
2 Troubleshooting Procedures To determine if the computer’s LAN port is functioning properly, perform the following procedures. Figure 2-14 outlines the process. Start with Procedure 1 and continue as instructed. Procedure 1: Diagnostic test Procedure 2: Connection and replacement check Procedure 1 Diagnostic test Run T&D Program on DOS model, which will display the LAN test result. If tests and diagnostics result abnormal go to Procedure 2. If an error is not located, the 3D functioning is properly.
2 Troubleshooting Procedures 2.16 MIC Troubleshooting Figure 2-15. MIC troubleshooting process The MIC module or system board may be the reason of a MIC fault. Either of these two components may be damaged. To determine if the computer’s MIC is functioning properly, perform the following procedures. Figure 2-15 outlines the process. Start with Procedure 1 and continue with the other procedures as instructed.
2 Troubleshooting Procedures Procedure 2: Connector and replacement check Procedure 1 Windows Application test Run the functioning Program (record.exe) on Windows model, which will display the MIC test result. If tests and diagnostics result abnormal go to Procedure 2. If an error is not located, the MIC module functioning is properly. Procedure 2 Connector and replacement check The MIC module or system board may be disconnected or damaged.
2 Troubleshooting Procedures 2.17 3D Sensor Troubleshooting Figure 2-16. 3D sensor troubleshooting process The operation or system board may be the reason of 3D sensor fault. Either of these two may be damaged. To determine if the computer’s 3D is functioning properly, perform the following procedures. Figure 2-16 outlines the process. Start with Procedure 1 and continue with the other procedures as instructed.
2 Troubleshooting Procedures Procedure 2 Replacement check Disassemble the computer following the steps described in Chapter 4, Replacement Procedures, and perform the following checks. Check 1 Make sure that 3D sensor test operation is correct, go to Check 2. Check 2 The system board may be damaged. Replace it with a new one following the instructions in Chapter 4.
2 Troubleshooting Procedures 2.18 3G Troubleshooting START P e r f o r m W in d o w s a p p lic a tio n te s t (P ro c e d u re 1 ) W a s a 3 G p r o b le m d e te c te d ? No 3 G s y s te m is n o t f a u lty . C o n tin u e tr o u b le s h o o tin g - r e f e r to F ig u r e 2 .
2 Troubleshooting Procedures functioning properly, perform the following procedures. Figure 2-17 outlines the process. Start with Procedure 1 and continue with the other procedures as instructed. Procedure 1: Windows Application check Procedure 2: Connector and replacement check Procedure 1 Windows Application check 1.> Please use TOSHIBA wireless manager. It displays the name of telecommunication company, and intensity of an electric wave. 2.> Please choose “About” and click “System Info”.
2 Troubleshooting Procedures Procedure 2 Connector and replacement check The 3G antenna, 3G unit or system board may be disconnected or damaged. Disassemble the computer following the steps described in Chapter 4, Replacement Procedures, and perform the following checks. Check 1 Make sure that the 3G antenna is firmly connected to the 3G module (refer to Chapter 4 for instructions) and that the 3G module is securely slotted into the system board. If the problem persists, go to Check 2.
2 Troubleshooting Procedures 2.
2 Troubleshooting Procedures Procedure 1: HDMI connection check Procedure 2: HDMI set check Procedure 1 HDMI connection check The CRT cable may be damaged or the connections may be loose. Perform Check 1: Check 1 Make sure HDMI cable is firmly plugged into both the CRT set and the CRT port of the computer. If the cable is connected correctly, go to Check 2. Check 2 Make sure the HDMI port is firmly secured to the system board of the computer. If the malfunction remains, go to Check 3.
2 Troubleshooting Procedures 2.20 E-SATA Troubleshooting START Perform E-SATA device check (Procedure 1) Is E-SATA transmission ok? Yes Perform diagnostic check (Procedure 2) No Was an E-SATA problem detected? No E-SATA port and transmission are not faulty.
2 Troubleshooting Procedures To determine if the computer’s E-SATA system is functioning properly, perform the following procedures. Figure 2-19 outlines the process. Start with Procedure 1 and continue with the other procedures as instructed. Procedure 1: E-SATA device check Procedure 2: Windows Application check Procedure 3: Connection and replacement check Procedure 1 E-SATA device check Connect an E-SATA device to the computer’s E-SATA port, and then boot the computer for Windows7.
2 Troubleshooting Procedures 2.21 Wimax Troubleshooting START Perform Wimax connection check (Procedure 1) Was a Wimax problem delected? No Wimax system is not faulty.
2 Troubleshooting Procedures The Wimax antenna wire, Wimax unit or system board may each be the source of a Wimax fault. Any of these components may be damaged. To determine if the computer’s Wimax system is functioning properly, perform the following procedures. Figure 2-20 outlines the process. Start with Procedure 1 and continue with the other procedures as instructed.
Chapter 3 Tests and Diagnostic
3. Tests and Diagnostics 3.1 The Diagnostic Test .................................................................................................................. 3 3.2 Executing the Diagnostic Test................................................................................................... 4 3.3 Display Configuration .............................................................................................................. 7 3.4 Audio sound Test...................................................
3. Tests and Diagnostics 3.1 The Diagnostic Test This chapter explains how to use the Test & Diagnostic program to test the functions of the (Base on Streamline S10 T&D version 1.0) hardware modules. The program consists of a series of tests that run automatically when the Diagnostics Program items are selected and executed. NOTES: To start the diagnostics, follow these steps 1. Check all cables for loose connections. 2. Exit this program when you are at Main Menu.
3. Tests and Diagnostics 3.2 Executing the Diagnostic Test Free-DOS is required to run the DIAGNOSTICS PROGRAM. To start the DIAGNOSTIC PROGRAM, follow these steps: Insert the diagnostics USB memory and turn on the computer. (The diagnostics USB memory contains the Free-DOS boot files.) And then follow the instructions for T&D program installed in USB memory.
3.
3. Tests and Diagnostics If an error is detected and a test fails, the following message displays: Then press any key for next actions, the below display presented.
3. Tests and Diagnostics 3.3 Display Configuration This Item will show the unit configuration. It includes: CPU (CPU type; Cache ; CPU speed ;CPU FSB) DDRAM SIZE Panel ID HDD type & capacity (Vendor ID. Model.) VRAM size / VGA CHIP TYPE Battery cell (3cell; 6cell.
3. Tests and Diagnostics 3.4 Audio sound test The audio sound test allows the user to aurally confirm the speaker functions. And the speaker will send out music during test. Before the Audio Test, you will see below note: Press any key, then the program will test below item: 1. Line out Left channel test 2. Line out Right channel test 3. Playing 44K wave file 4.
3.
3. Tests and Diagnostics Press any key, the program will return to the below display, and you can press “Y” or “N” to judge the result.
3. Tests and Diagnostics 3.5 Fan ON/OFF Test The fan test allows the user to test aurally whether the fan is working. And follow the below procedures for this test: The computer will let the fan be “ON” after any key pressed. Feel the wind or listen the rotating sound to check whether the fan is working or not. NOTE: Remember to approach fan outlet that is near left side of unit whether fan is “ON”. The computer will stop the fan working after any key pressed.
3.
3. Tests and Diagnostics 3.6 Main Battery Charge Test NOTE: The AC adaptor should be connected to successfully run this test . 45W with 19V DC for ALL SKU This test shows and measures the main battery: Battery type (Lion) Manufacturer (Sanyo/Panasonic/Sony) Remain charge capacity (0 ~ 100%) Charge function (PASS/FAIL) - “Battery Is Full” showed when “remain charge capacities” is 100% The screen should display as below, if the charge function is OK, will show:.
3 Tests and Diagnostics 3. 7 FDD Test NOTE: Before running the FDD test, prepare a formatted work diskette (1.44 MB). Need to insert FDD when power on machine. Otherwise the Floppy can not be detected. The Floppy Disk Test includes three subtests of the: 1. Sequential seek/verify function (Range: Track 0 ~ 79) 2. Funnel code seek/verify function (Range: Track 0 ~ 79) 3.
3. Tests and Diagnostics 3.8 Memory check This test will check if the computer’s Memory Frequency and Size is correct in every slot. Before Memory test start, you should choice the below item: 1. Memory Read test 2. Memory Write test 3. Memory Read & Write test 4. Memory INFO test 5.
3 Tests and Diagnostics When you execute this test, after you press the related number, the test picture will show as below: Memory Read Test Memory Write Test Satellite/Satellite PRO T230 Series Maintenance Manual 16
3. Tests and Diagnostics Memory Read & Write Test Memory Info Test NOTE: Base on normal status, the Memory Info speed show 800/667, then the RAM is DDR2; if speed show 1066, and then the RAM is DDR3.
3 Tests and Diagnostics 3.9 Keyboard Test The keyboard test checks the all keys function. NOTE: The Num Lock and the Overlay mode must be off to execute the keyboard test. Before keyboard test starts, the keyboard matrix code should be chosen as below display: 1. S (US, for America) 2. J (Japan, for Japan) 3. K(UK, for Europe) When you execute this test, the keyboard layout is drawn on the display. When any key is pressed, the corresponding key on the screen changes to black as shown below.
3.
3. Tests and Diagnostics 3.10 Mouse (Pad) Test The Mouse test allows the user to select and assign values to the following, using the Touch Pad or “Tab” key to move between selections: 1. Mouse Speed (on a scale from slow to fast) 2. Acceleration (Off, Low, Medium, High) 3. Button Assignments (Left + Right / Right button, either Unassigned or Drag Lock) 4. Swap Buttons (Left /Right) NOTE: The Touch Pad test cannot be used to test an external USB mouse.
3. Tests and Diagnostics 3.11 LCD Pixels Mode Test This LCD pixels mode test checks whether video display is fine. This test includes two modes of the test: 1. Text Mode - including 40*25 (16 colors) and 80*25 (2/16colors). 2. VGA Mode - including 320*200 (2/4/16 colors), 640*200 (2/16 colors), 640*350 (2/16 colors), 640*480 (2/16/256 colors). The screen should display as below, indicating whether the test is passed or failed after the question.
3. Tests and Diagnostics 3.12 Magnetic Switch Test The Magnetic switch test checks the Magnetic function of the unit. When LCD cover closed, the Magnetic should enable to turn off the display. Follow below steps to run this test: 1. Close the LCD cover. 2. Open the LCD. Then it will indicate whether the test is passed or failed. 1>.
3. Tests and Diagnostics 2>.
3. Tests and Diagnostics 3.13 LAN Test The LAN test checks the LAN full-duplex environment. NOTE: LAN loopback needs to plug in before test begins. And LAN information will show on the test screen: IO Base – Port: A000H IRQ – BH, it’s “IRQ B”. Node – it is “MAC Address”. Line Speed –1000 Mbps or 100Mbps or 10 Mbps. Bus ID – it’s “09”. The LAN test includes three subtests of the: 1. Speed1000 2. Speed100 3. Speed10 The subtests run automatically.
3.
3. Tests and Diagnostics 3.14 RTC Test Checks the computer’s RTC (Real Time Clock) and calendar functions by comparing the FreeDOS and CMOS values. The test runs automatically. The screen should display as below, indicating whether the test is passed or failed when finished. The screen will show below picture, if RTC test is OK. The screen will show below picture, if RTC test is FAIL.
3.
3. Tests and Diagnostics 3.15 3D G-sensor test NOTE: please keep 90 degree between logic upper and LCD panel when test The display of a test program and the set method of PC are shown below. Display of a Test Program, The portion which PC and Test-Fixture contact is green.
3. Tests and Diagnostics Front Upper 90° Set method of PC <4> Test 5: Left Upper 90° Set method of PC <5> Test Result A test result is displayed when a test is completed. A display of result is O.K. or NG. And an error flag is returned at the end of a program. If the picture shows as below, it means the 3D G-sensor function is OK.
3.
3. Tests and Diagnostics 3.16 HDD Test NOTE: You can press “Ctrl + Fn + Break” key to stop HDD test if you want The HDD test allows the user to verify the HDD ok or not.
3.
3.
3. Tests and Diagnostics 3.
3. Tests and Diagnostics 3.18 Write DMI When you want to write DMI data, please select which data you want to write, the figure below will be displayed: 1. Write Product (32) 2. Write Serial (32) 3. Write Version (32) 4. Write OEM String (64) 5. Back to test title After write OK, you should reboot the system that can make the setting effective, or you can write next data before reboot system, the figure below will displayed: If press “5” and press “ENTER”, program will back to test title.
3. Tests and Diagnostics NOTE: should input correct DMI data, and should reboot the system that can make the setting effective.
3. Tests and Diagnostics 3.19 Toshiba Logo set Set the computer’s Toshiba Logo for other region except Japan SKU. The screen should display as below, indicating whether the test is passed or failed when finished.
3.
3. Tests and Diagnostics 3.20 Dynabook Logo set Set the computer’s Dynabook Logo for Japan SKU. The screen should display as below, indicating whether the test is passed or failed when finished.
3.
3. Tests and Diagnostics 3.21 TP TYPE R/W TEST This T/P TYPE R/W test checks the computer’s T/P TYPE and users write T/P vendor ID into EEPROM. The test runs automatically. The screen should display as below, indicating whether the test is passed or failed when finished.
3.
3.
3. Tests and Diagnostics 3.22 EE-PROM SETTING This EE-PROM SETTING will set the computer’s function status into EEPROM, included supported function and no support function. NOTE: Should perform EE-PROM SETTING once change M/B. It defined as normal rule. The screen should display as below: If press “1” to set MIC function status in EE-PROM, the screen should display as below: Please check related information to judge this unit whether has MIC function.
3.
3.
3.
3.
Chapter 4 Replacement Procedures
4 Replacement Procedures Chapter 4 4.1 Contents General ................................................................................................................... 4-1 Safety Precautions .......................................................................................... 4-3 Before You Begin........................................................................................... 4-5 Disassembly Procedures .................................................................................
4 Replacement Procedures 4.8 Power Board ......................................................................................................... 4-29 Removing the Power Board ......................................................................... 4-29 Installing the Power Board ........................................................................... 4-30 4.9 RGB Board ...........................................................................................................
4 Replacement Procedures Installing the Bluetooth Combined With Cable Module.............................. 4-48 4.19 Thermal Fan ......................................................................................................... 4-50 Removing the Thermal Fan .......................................................................... 4-50 Installing the Thermal Fan ........................................................................... 4-51 4.20 Motherboard ......................................
4 Replacement Procedures Figures Figure 4.1 Removing the Battery Pack .................................................................................. 4-9 Figure 4.2 Removing the HDD door.................................................................................... 4-11 Figure 4.3 Removing the HDD ............................................................................................ 4-12 Figure 4.4 Removing the HDD bracket ......................................................................
4 Replacement Procedures Figure 4.32 Removing the Thermal Module........................................................................ 4-55 Figure 4.33 Reapply Shinetsu 7762 grease on the thermal module and remove any release papers ...................................................................................................................... 4-56 Figure 4.34 Removing two screws from LCD Bezel ........................................................... 4-57 Figure 4.35 Prying up the LCD Bezel ....
Fehler! Verwenden Sie die Registerkarte 'Start', um 標題 2 dem Text zuzuweisen, der hier angezeigt werden soll. Fehler! Verwenden Sie die Registerkarte 'Start', um 標題 2 dem Text zuzuweisen, der hier angezeigt 4 Replacement Procedures werden soll. 4.1 General This chapter explains how to disassemble the laptop and replace Field Replaceable Units (FRUs). Some replacement procedures may not require you to remove all the surrounding FRUs to replace only one FRU.
Fehler! Verwenden Sie die Registerkarte 'Start', um 標題 2 dem Text 4 Replacement Procedures zuzuweisen, der hier angezeigt werden soll. Fehler! Verwenden Sie die Registerkarte 'Start', um 標題 2 dem Text zuzuweisen, der hier angezeigt werden soll. 4.2 Battery 4.3 HDD 4.5 Keyboard 4.6 Logic Upper Assembly 4.4 Memory 4.7 Touch Pad Bracket and Touch Pad Button Board 4.8 Power Board 4.9 RGB Board 4.10 WLAN Card 4.11 WWAN Card 4.13 Display Assembly 4.12 Minicard Brackets 4.22 LCD Bezel 4.
Fehler! Verwenden Sie die Registerkarte 'Start', um 標題 2 dem Text zuzuweisen, der hier angezeigt werden soll. Fehler! Verwenden Sie die Registerkarte 'Start', um 標題 2 dem Text zuzuweisen, der hier angezeigt werden soll. 4 Replacement Procedures Safety Precautions Before you begin disassembly read the following safety precautions carefully. Be sure to follow them while you are working. DANGER: 1. Always use the genuine batteries or replacement batteries authorized by Toshiba.
4 Replacement Procedures Fehler! Verwenden Sie die Registerkarte 'Start', um 標題 2 dem Text zuzuweisen, der hier angezeigt werden soll. Fehler! Verwenden Sie die Registerkarte 'Start', um 標題 2 dem Text zuzuweisen, der hier angezeigt werden soll. 3. Before removing a FRU or other component, make sure that all the component cables have been disconnected to avoid the risk of electrical shock caused by accidental contact with the energized components. 4.
Fehler! Verwenden Sie die Registerkarte 'Start', um 標題 2 dem Text zuzuweisen, der hier angezeigt werden soll. Fehler! Verwenden Sie die Registerkarte 'Start', um 標題 2 dem Text zuzuweisen, der hier angezeigt werden soll. 4 Replacement Procedures Before You Begin Before you begin to disassemble the laptop, keep in mind the precautions and advice in this section. Always begin disassembly by removing the AC adapter and battery pack. Remove the optional parts and accessories as well.
4 Replacement Procedures Fehler! Verwenden Sie die Registerkarte 'Start', um 標題 2 dem Text zuzuweisen, der hier angezeigt werden soll. Fehler! Verwenden Sie die Registerkarte 'Start', um 標題 2 dem Text zuzuweisen, der hier angezeigt werden soll.
Fehler! Verwenden Sie die Registerkarte 'Start', um 標題 2 dem Text zuzuweisen, der hier angezeigt werden soll. Fehler! Verwenden Sie die Registerkarte 'Start', um 標題 2 dem Text zuzuweisen, der hier angezeigt 4 Replacement Procedures werden soll. Tools and Equipment For your safety and that of other people in the working environment, it is strongly recommended that you use electrostatic discharge (ESD) equipment.
4 Replacement Procedures Fehler! Verwenden Sie die Registerkarte 'Start', um 標題 2 dem Text zuzuweisen, der hier angezeigt werden soll. Fehler! Verwenden Sie die Registerkarte 'Start', um 標題 2 dem Text zuzuweisen, der hier angezeigt werden soll.
Fehler! Verwenden Sie die Registerkarte 'Start', um 標題 2 dem Text zuzuweisen, der hier angezeigt werden soll. Fehler! Verwenden Sie die Registerkarte 'Start', um 標題 2 dem Text zuzuweisen, der hier angezeigt 4 Replacement Procedures werden soll. 4.2 Battery Removing the Battery Pack Remove the battery pack according to the following procedures and Figure 4.1. CAUTION: When handling the battery packs, use care not to short circuit the terminals. Do not drop, hit, twist, or bend the battery packs.
4 Replacement Procedures Fehler! Verwenden Sie die Registerkarte 'Start', um 標題 2 dem Text zuzuweisen, der hier angezeigt werden soll. Fehler! Verwenden Sie die Registerkarte 'Start', um 標題 2 dem Text zuzuweisen, der hier angezeigt werden soll. Installing the Battery Pack Install the battery pack according to the following procedures. CAUTION: The battery packs contain a lithium ion battery, which can explode due to improper replacement, use, handling, or disposal.
Fehler! Verwenden Sie die Registerkarte 'Start', um 標題 2 dem Text zuzuweisen, der hier angezeigt werden soll. Fehler! Verwenden Sie die Registerkarte 'Start', um 標題 2 dem Text zuzuweisen, der hier angezeigt 4 Replacement Procedures werden soll. 4.3 HDD Removing the HDD CAUTION: Do not press on the top or bottom of the drive. Applying such pressure can either corrupt the data in the drive or damage the drive. Remove the HDD (hard disk drive) according to the following procedures and Figures 4.2, 4.
4 Replacement Procedures Fehler! Verwenden Sie die Registerkarte 'Start', um 標題 2 dem Text zuzuweisen, der hier angezeigt werden soll. Fehler! Verwenden Sie die Registerkarte 'Start', um 標題 2 dem Text zuzuweisen, der hier angezeigt werden soll. 2. Remove the two M2x3 screws and remove the HDD by pulling the tab attached to the HDD. OU T M2×3*2 IN Figure 4.3 Removing the HDD NOTE: Do not disassemble the HDD pack when it is working normally. Disassemble or replace the HDD pack only if it fails. 3.
Fehler! Verwenden Sie die Registerkarte 'Start', um 標題 2 dem Text zuzuweisen, der hier angezeigt werden soll. Fehler! Verwenden Sie die Registerkarte 'Start', um 標題 2 dem Text zuzuweisen, der hier angezeigt 4 Replacement Procedures werden soll. 3 4 M3×3*4 2 1 Figure 4.4 Removing the HDD bracket CAUTION: Do not apply pressure to the top or bottom of the drive. Installing the HDD Install the HDD according to the following procedures. CAUTION: To avoid damage, always hold the HDD only by its sides. 1.
Fehler! Verwenden Sie die Registerkarte 'Start', um 標題 2 dem Text 4 Replacement Procedures zuzuweisen, der hier angezeigt werden soll. Fehler! Verwenden Sie die Registerkarte 'Start', um 標題 2 dem Text zuzuweisen, der hier angezeigt werden soll. 4.4 Memory Removing the Optional Memory Remove the optional memory according to the following procedures and Figure 4.5 and 4.6 after checking that the laptop is turned off. CAUTION: Remove the optional memory after turning off the laptop.
Fehler! Verwenden Sie die Registerkarte 'Start', um 標題 2 dem Text zuzuweisen, der hier angezeigt werden soll. Fehler! Verwenden Sie die Registerkarte 'Start', um 標題 2 dem Text zuzuweisen, der hier angezeigt 4 Replacement Procedures werden soll. 5. Pull the memory up and out at a 45 degree angle, using care to avoid touching the connectors. Figure 4.6 Removing the memory from the laptop 6. Repeat steps 4 and 5 to remove the other memory.
4 Replacement Procedures Fehler! Verwenden Sie die Registerkarte 'Start', um 標題 2 dem Text zuzuweisen, der hier angezeigt werden soll. Fehler! Verwenden Sie die Registerkarte 'Start', um 標題 2 dem Text zuzuweisen, der hier angezeigt werden soll. Installing the Optional Memory Install the optional memory according to the following procedures after checking that the laptop is turned off. CAUTION: Install the optional memory after turning off the laptop.
Fehler! Verwenden Sie die Registerkarte 'Start', um 標題 2 dem Text zuzuweisen, der hier angezeigt werden soll. Fehler! Verwenden Sie die Registerkarte 'Start', um 標題 2 dem Text zuzuweisen, der hier angezeigt 4 Replacement Procedures werden soll. 4.5 Keyboard Removing the Keyboard Remove the Keyboard according to the following procedures and Figures 4.7, 4.8, 4.9 and 4.10. 1. Turn the laptop upside down and remove the two M2x6 screws as indicated in Figure 4.7. M2×6*2 Figure 4.7 Removing two screws 2.
4 Replacement Procedures Fehler! Verwenden Sie die Registerkarte 'Start', um 標題 2 dem Text zuzuweisen, der hier angezeigt werden soll. Fehler! Verwenden Sie die Registerkarte 'Start', um 標題 2 dem Text zuzuweisen, der hier angezeigt werden soll. Figure 4.
Fehler! Verwenden Sie die Registerkarte 'Start', um 標題 2 dem Text zuzuweisen, der hier angezeigt werden soll. Fehler! Verwenden Sie die Registerkarte 'Start', um 標題 2 dem Text zuzuweisen, der hier angezeigt 4 Replacement Procedures werden soll. 3. Lift the keyboard up and move it upward. Figure 4.9 Lifting up the keyboard 4. Disconnect the keyboard FPC from the motherboard and remove the keyboard.
4 Replacement Procedures Fehler! Verwenden Sie die Registerkarte 'Start', um 標題 2 dem Text zuzuweisen, der hier angezeigt werden soll. Fehler! Verwenden Sie die Registerkarte 'Start', um 標題 2 dem Text zuzuweisen, der hier angezeigt werden soll. Figure 4.
Fehler! Verwenden Sie die Registerkarte 'Start', um 標題 2 dem Text zuzuweisen, der hier angezeigt werden soll. Fehler! Verwenden Sie die Registerkarte 'Start', um 標題 2 dem Text zuzuweisen, der hier angezeigt werden soll. 4 Replacement Procedures Installing the keyboard Cover and Keyboard Install the keyboard cover and keyboard according to the following procedures. 1. Connect the FPC on the back of the keyboard to the motherboard and place the keyboard in the correct position. 2.
4 Replacement Procedures Fehler! Verwenden Sie die Registerkarte 'Start', um 標題 2 dem Text zuzuweisen, der hier angezeigt werden soll. Fehler! Verwenden Sie die Registerkarte 'Start', um 標題 2 dem Text zuzuweisen, der hier angezeigt werden soll. 4.6 Logic Upper Assembly Removing the Logic Upper Assembly Remove the logic upper assembly according to the following procedures and Figures 4.11, 4.12 and 4.13. 1. Turn the laptop upside down and remove the nine M2x6 screws. M2×6*9 Figure 4.
Fehler! Verwenden Sie die Registerkarte 'Start', um 標題 2 dem Text zuzuweisen, der hier angezeigt werden soll. Fehler! Verwenden Sie die Registerkarte 'Start', um 標題 2 dem Text zuzuweisen, der hier angezeigt 4 Replacement Procedures werden soll. 2. Turn the laptop over and open it. Disconnect the power board FFC and touchpad FFC from the motherboard and remove the four M2x3 and one M2x6 screws. M2×3*4 M2×6*1 Figure 4.
4 Replacement Procedures Fehler! Verwenden Sie die Registerkarte 'Start', um 標題 2 dem Text zuzuweisen, der hier angezeigt werden soll. Fehler! Verwenden Sie die Registerkarte 'Start', um 標題 2 dem Text zuzuweisen, der hier angezeigt werden soll. 3. Pry up the logic upper assembly from its top and remove it from the logic lower assembly. Figure 4.13 Removing the logic upper assembly Installing the Logic Upper Assembly Install the logic upper assembly according to the following procedures. 7.
Fehler! Verwenden Sie die Registerkarte 'Start', um 標題 2 dem Text zuzuweisen, der hier angezeigt werden soll. Fehler! Verwenden Sie die Registerkarte 'Start', um 標題 2 dem Text zuzuweisen, der hier angezeigt werden soll. 4 Replacement Procedures 10. Turn the laptop upside down and secure it with nine M2x6 screws as indicated in Figure 4.11.
4 Replacement Procedures Fehler! Verwenden Sie die Registerkarte 'Start', um 標題 2 dem Text zuzuweisen, der hier angezeigt werden soll. Fehler! Verwenden Sie die Registerkarte 'Start', um 標題 2 dem Text zuzuweisen, der hier angezeigt werden soll. 4.7 Touch Pad Bracket and TP Button Board Removing the Touch Pad Bracket and TP Button Board Remove the Touch Pad Bracket and TP Button Board according to the following procedures and Figures 4.14, and 4.15. 1.
Fehler! Verwenden Sie die Registerkarte 'Start', um 標題 2 dem Text zuzuweisen, der hier angezeigt werden soll. Fehler! Verwenden Sie die Registerkarte 'Start', um 標題 2 dem Text zuzuweisen, der hier angezeigt 4 Replacement Procedures werden soll. 2. Flip over the touch pad bracket and remove the TP button board from the bracket. Figure 4.
4 Replacement Procedures Fehler! Verwenden Sie die Registerkarte 'Start', um 標題 2 dem Text zuzuweisen, der hier angezeigt werden soll. Fehler! Verwenden Sie die Registerkarte 'Start', um 標題 2 dem Text zuzuweisen, der hier angezeigt werden soll. Installing the Touch Pad Bracket and TP Button Board Install the Touch Pad Bracket and TP Button Board according to the following procedures. 1. Seat the TP button board in the correct position on the touch pad bracket. 2.
Fehler! Verwenden Sie die Registerkarte 'Start', um 標題 2 dem Text zuzuweisen, der hier angezeigt werden soll. Fehler! Verwenden Sie die Registerkarte 'Start', um 標題 2 dem Text zuzuweisen, der hier angezeigt 4 Replacement Procedures werden soll. 4.8 Power Board Removing the Power Board Remove the Power Board according to the following procedures and Figures 4.16 and 4.17. 1. Peel the power board FFC off the logic upper assembly as indicated in Figure 4.16. Figure 4.
4 Replacement Procedures Fehler! Verwenden Sie die Registerkarte 'Start', um 標題 2 dem Text zuzuweisen, der hier angezeigt werden soll. Fehler! Verwenden Sie die Registerkarte 'Start', um 標題 2 dem Text zuzuweisen, der hier angezeigt werden soll. 2. Turn the logic upper assembly upside down. Remove one M2x4 screw and remove the power board from the logic upper assembly. M2×4*1 Figure 4.17 Removing the power board Installing the Power Board Install the Power Board according to the following procedures. 1.
Fehler! Verwenden Sie die Registerkarte 'Start', um 標題 2 dem Text zuzuweisen, der hier angezeigt werden soll. Fehler! Verwenden Sie die Registerkarte 'Start', um 標題 2 dem Text zuzuweisen, der hier angezeigt 4 Replacement Procedures werden soll. 4.9 RGB Board Removing the RGB Board Remove the RGB Board according to the following procedures and Figures 4.18 and 4.19. 1. Disconnect the FFC from the motherboard and peel it off the logic lower assembly. 2.
4 Replacement Procedures Fehler! Verwenden Sie die Registerkarte 'Start', um 標題 2 dem Text zuzuweisen, der hier angezeigt werden soll. Fehler! Verwenden Sie die Registerkarte 'Start', um 標題 2 dem Text zuzuweisen, der hier angezeigt werden soll. 3. Lift the board up to an angle and then remove it from the logic lower assembly as indicated in Figure 4.19. Figure 4.19 Removing the RGB Board Installing the RGB Board Install the RGB Board according to the following procedures. 1.
Fehler! Verwenden Sie die Registerkarte 'Start', um 標題 2 dem Text zuzuweisen, der hier angezeigt werden soll. Fehler! Verwenden Sie die Registerkarte 'Start', um 標題 2 dem Text zuzuweisen, der hier angezeigt 4 Replacement Procedures werden soll. 4.10 WLAN Card Removing the WLAN Card Remove the WLAN card according to the following procedures and Figure 4.20. 1. Disconnect two antenna cables from the WLAN card. 2. Remove the two M2x3 screws securing the WLAN card. The card pops up automatically. 3.
4 Replacement Procedures Fehler! Verwenden Sie die Registerkarte 'Start', um 標題 2 dem Text zuzuweisen, der hier angezeigt werden soll. Fehler! Verwenden Sie die Registerkarte 'Start', um 標題 2 dem Text zuzuweisen, der hier angezeigt werden soll. Installing the WLAN Card Install the WLAN card according to the following procedures. 1. Insert the WLAN card into the connector on the motherboard at an angle of 45 degrees. 2. Press the WLAN card down and secure it with two M2x3 screws. 3.
Fehler! Verwenden Sie die Registerkarte 'Start', um 標題 2 dem Text zuzuweisen, der hier angezeigt werden soll. Fehler! Verwenden Sie die Registerkarte 'Start', um 標題 2 dem Text zuzuweisen, der hier angezeigt 4 Replacement Procedures werden soll. 4.11 WWAN Card Removing the WWAN Card Remove the WWAN card according to the following procedures and Figure 4.21. 1. Disconnect two antenna cables from the WWAN card. 2. Remove the two M2x3 screws securing the WWAN card. The card pops up automatically. 3.
4 Replacement Procedures Fehler! Verwenden Sie die Registerkarte 'Start', um 標題 2 dem Text zuzuweisen, der hier angezeigt werden soll. Fehler! Verwenden Sie die Registerkarte 'Start', um 標題 2 dem Text zuzuweisen, der hier angezeigt werden soll. Installing the WWAN Card Install the WWAN card according to the following procedures. 1. Insert the WWAN card into the connector on the motherboard at an angle of 45 degrees. 2. Press the WWAN card down and secure it with two M2x3 screws. 3.
Fehler! Verwenden Sie die Registerkarte 'Start', um 標題 2 dem Text zuzuweisen, der hier angezeigt werden soll. Fehler! Verwenden Sie die Registerkarte 'Start', um 標題 2 dem Text zuzuweisen, der hier angezeigt 4 Replacement Procedures werden soll. 4.12 Minicard Brackets Removing the Minicard Brackets There are two minicard brackets on the logic lower assembly. Remove each of the minicard brackets according to the following procedures and Figures 4.22. 1.
4 Replacement Procedures Fehler! Verwenden Sie die Registerkarte 'Start', um 標題 2 dem Text zuzuweisen, der hier angezeigt werden soll. Fehler! Verwenden Sie die Registerkarte 'Start', um 標題 2 dem Text zuzuweisen, der hier angezeigt werden soll. 2. Repeat step one with the other minicard bracket.
Fehler! Verwenden Sie die Registerkarte 'Start', um 標題 2 dem Text zuzuweisen, der hier angezeigt werden soll. Fehler! Verwenden Sie die Registerkarte 'Start', um 標題 2 dem Text zuzuweisen, der hier angezeigt 4 Replacement Procedures werden soll. 4.13 Display Assembly Removing the Display Assembly CAUTION: Use care to avoid the antenna cable being caught between the display assembly and the laptop. Remove the display assembly according to the following procedures and Figure 4.23. 1.
4 Replacement Procedures Fehler! Verwenden Sie die Registerkarte 'Start', um 標題 2 dem Text zuzuweisen, der hier angezeigt werden soll. Fehler! Verwenden Sie die Registerkarte 'Start', um 標題 2 dem Text zuzuweisen, der hier angezeigt werden soll. Installing the Display Assembly Install the display assembly according to the following procedures. 1. Seat the display hinge brackets in the correct position on the logic lower assembly and secure it with three M2x6 screws. 2.
Fehler! Verwenden Sie die Registerkarte 'Start', um 標題 2 dem Text zuzuweisen, der hier angezeigt werden soll. Fehler! Verwenden Sie die Registerkarte 'Start', um 標題 2 dem Text zuzuweisen, der hier angezeigt 4 Replacement Procedures werden soll. 4.14 USB & Audio Board Removing the USB & Audio Board Remove the USB & Audio Board according to the following procedures and Figure 4.24. 1. Disconnect the FFC from the motherboard and peel it off the logic lower assembly. 2.
4 Replacement Procedures Fehler! Verwenden Sie die Registerkarte 'Start', um 標題 2 dem Text zuzuweisen, der hier angezeigt werden soll. Fehler! Verwenden Sie die Registerkarte 'Start', um 標題 2 dem Text zuzuweisen, der hier angezeigt werden soll. 1. Seat the USB & Audio board in the correct position on the logic lower assembly and secure it with two M2x3 screws. 2. Adhere the FFC to the logic lower assembly and connect it to the motherboard.
Fehler! Verwenden Sie die Registerkarte 'Start', um 標題 2 dem Text zuzuweisen, der hier angezeigt werden soll. Fehler! Verwenden Sie die Registerkarte 'Start', um 標題 2 dem Text zuzuweisen, der hier angezeigt 4 Replacement Procedures werden soll. 4.15 HDD Board Removing the HDD Board Remove the HDD Board according to the following procedures and Figures 4.25 and 4.26. 1. Disconnect the FFC from the motherboard and peel it off the logic lower assembly. 2.
4 Replacement Procedures Fehler! Verwenden Sie die Registerkarte 'Start', um 標題 2 dem Text zuzuweisen, der hier angezeigt werden soll. Fehler! Verwenden Sie die Registerkarte 'Start', um 標題 2 dem Text zuzuweisen, der hier angezeigt werden soll. 3. Turn the logic lower assembly upside down and remove the HDD board as indicated in Figure 4.26. Figure 4.26 Removing the HDD Board Installing the HDD Board Install the HDD Board according to the following procedures. 1.
Fehler! Verwenden Sie die Registerkarte 'Start', um 標題 2 dem Text zuzuweisen, der hier angezeigt werden soll. Fehler! Verwenden Sie die Registerkarte 'Start', um 標題 2 dem Text zuzuweisen, der hier angezeigt 4 Replacement Procedures werden soll. 4.16 LED Board Removing the LED Board Remove the LED Board according to the following procedures and Figure 4.27. 1. Disconnect the LED cable from the motherboard and pull it out of the routing channel. 2. Pry the fixing ribs outward as indicated in Figure 4.
4 Replacement Procedures Fehler! Verwenden Sie die Registerkarte 'Start', um 標題 2 dem Text zuzuweisen, der hier angezeigt werden soll. Fehler! Verwenden Sie die Registerkarte 'Start', um 標題 2 dem Text zuzuweisen, der hier angezeigt werden soll. 4.17 Speakers Removing the Speakers Remove the Speakers according to the following procedures and Figure 4.28. 1. Disconnect the cable from the motherboard. 2. Remove the two speakers from the logic lower assembly. Figure 4.
Fehler! Verwenden Sie die Registerkarte 'Start', um 標題 2 dem Text zuzuweisen, der hier angezeigt werden soll. Fehler! Verwenden Sie die Registerkarte 'Start', um 標題 2 dem Text zuzuweisen, der hier angezeigt werden soll. 4 Replacement Procedures 1. Seat the left and right speaker in the correct position. 2. Connect the speaker cable to the motherboard.
4 Replacement Procedures Fehler! Verwenden Sie die Registerkarte 'Start', um 標題 2 dem Text zuzuweisen, der hier angezeigt werden soll. Fehler! Verwenden Sie die Registerkarte 'Start', um 標題 2 dem Text zuzuweisen, der hier angezeigt werden soll. 4.18 Bluetooth Combined With Cable Module Removing the Bluetooth Combined With Cable Module Remove the Bluetooth combined with cable module according to the following procedures and Figure 4.29. 1. Disconnect the Bluetooth cable from the motherboard. 2.
Fehler! Verwenden Sie die Registerkarte 'Start', um 標題 2 dem Text zuzuweisen, der hier angezeigt werden soll. Fehler! Verwenden Sie die Registerkarte 'Start', um 標題 2 dem Text zuzuweisen, der hier angezeigt werden soll. 4 Replacement Procedures 2. Connect the Bluetooth cable to the motherboard.
4 Replacement Procedures Fehler! Verwenden Sie die Registerkarte 'Start', um 標題 2 dem Text zuzuweisen, der hier angezeigt werden soll. Fehler! Verwenden Sie die Registerkarte 'Start', um 標題 2 dem Text zuzuweisen, der hier angezeigt werden soll. 4.19 Thermal Fan Removing the Thermal Fan Remove the thermal fan according to the following procedures and Figure 4.30. 1. Disconnect the cable from the motherboard. 2. Remove one M2x4 screw from the thermal fan. 3.
Fehler! Verwenden Sie die Registerkarte 'Start', um 標題 2 dem Text zuzuweisen, der hier angezeigt werden soll. Fehler! Verwenden Sie die Registerkarte 'Start', um 標題 2 dem Text zuzuweisen, der hier angezeigt werden soll. 4 Replacement Procedures Installing the Thermal Fan Install the thermal fan according to the following procedures. 1. Seat the thermal fan in the correct position on the logic lower assembly. 2. Secure the thermal fan with one M2x4 screw. 3. Connect the cable to the motherboard.
4 Replacement Procedures Fehler! Verwenden Sie die Registerkarte 'Start', um 標題 2 dem Text zuzuweisen, der hier angezeigt werden soll. Fehler! Verwenden Sie die Registerkarte 'Start', um 標題 2 dem Text zuzuweisen, der hier angezeigt werden soll. 4.20 Motherboard Removing the Motherboard Remove the motherboard according to the following procedures and Figure 4.31. 1. Pull the DC IN connector out of the logic lower assembly. 2. Remove the five M2x3 screws as indicated in Figure 4. 31. M2×3*5 Figure 4.
Fehler! Verwenden Sie die Registerkarte 'Start', um 標題 2 dem Text zuzuweisen, der hier angezeigt werden soll. Fehler! Verwenden Sie die Registerkarte 'Start', um 標題 2 dem Text zuzuweisen, der hier angezeigt werden soll. 4 Replacement Procedures Installing the Motherboard Install the motherboard according to the following procedures. 1. Seat the motherboard in the correct position on the logic lower assembly. 2. Put the DC IN connector in the DC IN trough on the logic lower assembly. 3.
4 Replacement Procedures Fehler! Verwenden Sie die Registerkarte 'Start', um 標題 2 dem Text zuzuweisen, der hier angezeigt werden soll. Fehler! Verwenden Sie die Registerkarte 'Start', um 標題 2 dem Text zuzuweisen, der hier angezeigt werden soll. 4.21 Thermal Module Removing the Thermal Module Remove the thermal module according to the following procedures and Figure 4.32. CAUTION: When removing the thermal module, keep the following in mind: 1. The unit can become very hot during operation.
Fehler! Verwenden Sie die Registerkarte 'Start', um 標題 2 dem Text zuzuweisen, der hier angezeigt werden soll. Fehler! Verwenden Sie die Registerkarte 'Start', um 標題 2 dem Text zuzuweisen, der hier angezeigt 4 Replacement Procedures werden soll. 3 2 1 4 Figure 4.32 Removing the Thermal Module Installing the Thermal Module Install the Thermal Module according to the following procedures. 1. Reapply Shinetsu 7762 grease on the thermal module as shown in Figure 4.33.
4 Replacement Procedures Fehler! Verwenden Sie die Registerkarte 'Start', um 標題 2 dem Text zuzuweisen, der hier angezeigt werden soll. Fehler! Verwenden Sie die Registerkarte 'Start', um 標題 2 dem Text zuzuweisen, der hier angezeigt werden soll. Thermal pad ThermalGrease Thermal pad Figure 4.33 Reapply Shinetsu 7762 grease on the thermal module and remove any release papers 2. Seat the thermal module on the motherboard and secure it with four M2x4.
Fehler! Verwenden Sie die Registerkarte 'Start', um 標題 2 dem Text zuzuweisen, der hier angezeigt werden soll. Fehler! Verwenden Sie die Registerkarte 'Start', um 標題 2 dem Text zuzuweisen, der hier angezeigt 4 Replacement Procedures werden soll. 4.22 LCD Bezel Removing the LCD Bezel Remove the LCD bezel according to the following procedures and Figures 4.34, 4.35 and 4.36. 1. Remove the two screw rubbers on the LCD bezel. 2. Remove the two M2x6 screws. M2×6*2 Figure 4.
4 Replacement Procedures Fehler! Verwenden Sie die Registerkarte 'Start', um 標題 2 dem Text zuzuweisen, der hier angezeigt werden soll. Fehler! Verwenden Sie die Registerkarte 'Start', um 標題 2 dem Text zuzuweisen, der hier angezeigt werden soll. Figure 4.35 Prying up the LCD Bezel 5. Push up the hinge caps to free it from the LCD hinges and remove the LCD bezel. Figure 4.
Fehler! Verwenden Sie die Registerkarte 'Start', um 標題 2 dem Text zuzuweisen, der hier angezeigt werden soll. Fehler! Verwenden Sie die Registerkarte 'Start', um 標題 2 dem Text zuzuweisen, der hier angezeigt werden soll. 4 Replacement Procedures Installing the LCD Bezel Install the LCD bezel according to the following procedures. 1. Place the LCD bezel on the LCD cover assembly.
4 Replacement Procedures Fehler! Verwenden Sie die Registerkarte 'Start', um 標題 2 dem Text zuzuweisen, der hier angezeigt werden soll. Fehler! Verwenden Sie die Registerkarte 'Start', um 標題 2 dem Text zuzuweisen, der hier angezeigt werden soll. 4.23 LCD Module Removing the LCD Module Remove the LCD module according to the following procedures and Figures 4.37, 4.38, 4.39 and 4.40. 1. Remove the six M2x4 screws securing the LCD module to the LCD cover assembly. 2.
Fehler! Verwenden Sie die Registerkarte 'Start', um 標題 2 dem Text zuzuweisen, der hier angezeigt werden soll. Fehler! Verwenden Sie die Registerkarte 'Start', um 標題 2 dem Text zuzuweisen, der hier angezeigt 4 Replacement Procedures werden soll. M2×4*6 Figure 4.37 Removing the LCD Module from the LCD cover assembly 3. Disconnect the cable from the camera module.
4 Replacement Procedures Fehler! Verwenden Sie die Registerkarte 'Start', um 標題 2 dem Text zuzuweisen, der hier angezeigt werden soll. Fehler! Verwenden Sie die Registerkarte 'Start', um 標題 2 dem Text zuzuweisen, der hier angezeigt werden soll. Figure 4.38 Disconnect the cable from the camera module. 4. Lift the LCD module out of the LCD cover assembly. 5. Remove the six M2x3 screws and then remove the LCD hinges. M2×3*6 1 2 3 1 2 3 Figure 4.
Fehler! Verwenden Sie die Registerkarte 'Start', um 標題 2 dem Text zuzuweisen, der hier angezeigt werden soll. Fehler! Verwenden Sie die Registerkarte 'Start', um 標題 2 dem Text zuzuweisen, der hier angezeigt 4 Replacement Procedures werden soll. 6. Turn the LCD module over and place it face down on a protective surface, such as a foam pad. 7. Disconnect the LVDS cable connector. Then remove the tape and peel the LVDS cable from the LCD panel. Figure 4.
4 Replacement Procedures Fehler! Verwenden Sie die Registerkarte 'Start', um 標題 2 dem Text zuzuweisen, der hier angezeigt werden soll. Fehler! Verwenden Sie die Registerkarte 'Start', um 標題 2 dem Text zuzuweisen, der hier angezeigt werden soll. Installing the LCD Module Install the inverter board according to the following procedures. 1. Connect the LVDS cable to the LCD panel connector. 2.
Fehler! Verwenden Sie die Registerkarte 'Start', um 標題 2 dem Text zuzuweisen, der hier angezeigt werden soll. Fehler! Verwenden Sie die Registerkarte 'Start', um 標題 2 dem Text zuzuweisen, der hier angezeigt 4 Replacement Procedures werden soll. 4.24 Camera Module Removing the Camera Module Remove the Camera Module according to the following procedures and Figure 4.42. 1. Peel the camera module off the LCD cover assembly. Figure 4.
4 Replacement Procedures Fehler! Verwenden Sie die Registerkarte 'Start', um 標題 2 dem Text zuzuweisen, der hier angezeigt werden soll. Fehler! Verwenden Sie die Registerkarte 'Start', um 標題 2 dem Text zuzuweisen, der hier angezeigt werden soll. 1. Seat the camera module in the correct position on the LCD cover assembly. Press the camera module down to make sure it is adhered to the LCD cover assembly.
Fehler! Verwenden Sie die Registerkarte 'Start', um 標題 2 dem Text zuzuweisen, der hier angezeigt werden soll. Fehler! Verwenden Sie die Registerkarte 'Start', um 標題 2 dem Text zuzuweisen, der hier angezeigt 4 Replacement Procedures werden soll. 4.25 Antennas for WLAN Removing the Antennas for WLAN Remove the Antennas for WLAN according to the following procedures and Figures 4.43 and 4.44. 1. Pull the antennas out from the cable routing channel on the LCD cover assembly. Figure 4.
4 Replacement Procedures Fehler! Verwenden Sie die Registerkarte 'Start', um 標題 2 dem Text zuzuweisen, der hier angezeigt werden soll. Fehler! Verwenden Sie die Registerkarte 'Start', um 標題 2 dem Text zuzuweisen, der hier angezeigt werden soll. 2. Peel off the foil adhered on antennas as indicated in Figure 4.44, and then peel off the antennas from the LCD cover assembly. Figure 4.
Fehler! Verwenden Sie die Registerkarte 'Start', um 標題 2 dem Text zuzuweisen, der hier angezeigt werden soll. Fehler! Verwenden Sie die Registerkarte 'Start', um 標題 2 dem Text zuzuweisen, der hier angezeigt werden soll. 4 Replacement Procedures Installing the Antennas for WLAN Install the Antennas for WLAN according to the following procedures. 1. Stick the antennas in the correct position on the LCD cover assembly.
Appendix A Appendix A Handling the LCD Module Precautions for handling the LCD module The LCD module can be easily damaged during assembly or disassembly. Observe the following precautions when handling it to prevent damaging it. 1. When installing the LCD module in the display assembly, make sure that you seat it so that it is properly aligned and maximum visibility of the display is maintained. 2.
3. If the panel’s surface gets dirty or moist, wipe it with cotton or a soft cloth. If it is still dirty, try breathing on the surface to create a light condensate and wipe it again. If the surface is very dirty, we recommend a CRT cleaning agent. Apply the agent to a soft cloth and then wipe the panel’s surface. Do not apply cleanser directly to the panel. CRT Cleaner 4. If water or other liquid is left on the panel’s surface for a long period, it can change the screen’s tint or stain it.
5. Glass is used in the panel, so be careful not to drop it or let it strike a hard object, which could cause breakage or cracks. 6. CMOS-LSI circuits are used in the module, so guard against damage from electrostatic discharge. Be sure to wear a wrist or ankle grounding device when handling the module.
7. Do not expose the module to direct sunlight or strong ultraviolet rays for long periods. 8. Do not store the module at temperatures below its specifications. Cold can cause the liquid crystals to freeze, lose their elasticity or otherwise suffer damage. 9. Do not disassemble the LCD module. Disassembly can cause malfunctions.
10. If you transport the module, do not use packing material that contains epoxy resin (amine) or silicon glue (alcohol or oxime). These materials can release gas that can damage the panel’s polarization.
Appendix B Appendix B Board Layout B.
B.
Satellite/Satellite PRO T230/T230D Maintenance Manual B-3
Table B-1 System Board ICs (top and bottom) Number Name U5 Clock Generator (RTM890N-631-VB-GRT) U15 EC (KB926QFE0) U9 BIOS ROM (4MB SPI) U16 EC ROM (256KB SPI) UA1 CODEC (ALC269Q-VB5-GR) UC1 Card Reader Controller (JMB385-QGAZ0C) UL1 LAN Controller (RTL8105E/RTL8111E -VB-GR) UL2 LAN Transformer U1 Arrandale BGA CPU U8 Calpella PCH U6 HDMI level shift IC (ASM1442) Table B-2 System Board Connectors (top and bottom) B-4 Number Name JFAN Fan conn. JLVDS LVDS conn.
PJP2 11.6” Battery conn. JPJP3 13” Battery conn. JLED LED/B conn. JBJ RTC Battery.
C. Appendix C Pin Assignments System Board C.1 JFAN Table C-1 FAN I/F pin assignments (3-pin) Pin No. C.2 Signal name 1 +FAN1 3 GND I/O Pin No. Signal Name 2 FAN_SPEED1 I/O - JLVDS Table C-2 LVDS I/F pin assignments (30-pin) Pin No. Signal name I/O Pin No.
C.3 JP1 Table C-3 JP1 pin assignments (20-pin) Pin No. C.4 Signal name I/O Pin No. Signal Name I/O 1 RJ45_GND - 2 RJ45_MIDI1+ - 3 RJ45_MIDI1- - 4 GND - 5 RJ45_MIDI0+ - 6 RJ45_MIDI0- - 7 GND - 8 UMA_CRT_CLK - 9 UMA_CRT_DAT A - 10 UMA_CRT_VSYN C - 11 UMA_CRT_HSY NC - 12 GND - 13 CRT_R O 14 CRT_G O 15 CRT_B O 16 GND - 17 +3VS O 18 +5VS - 19 +5VS 20 +5VS - JHDMI Table C-4 HDMI I/F pin assignments (19-pin) Pin No. C.5 Signal name I/O Pin No.
Pin No. Signal name I/O Pin No. Signal Name 1 +5VS 2 +5VS 3 +5VS 4 +5VS 5 GND 6 SATA_PTX_C _DRX_P1 7 SATA_PTX_C _DRX_N1 I/O 8 GND 9 SATA_PRX_D TX_N1 I/O 10 SATA_PRX_D TX_P1 11 GND 12 GND I/O I/O I/O C.6 JESATA Table C-7 eSATA/USB I/F pin assignments (11-pin) Pin No. C.7 Signal name 1 +USB_VCCB 3 USB20_P3_RL 5 GND 7 SATA_PTX_C_DRX_N 5 9 SATA_PRX_DTX_N5 11 GND I/O Pin No.
Pin No. C.9 Signal name I/O Pin No. Signal Name 1 +3VALW - 2 NA 3 ON/OFFBTN# O 4 GND I/O JWLAN Table C-10 WLAN Connector pin assignments (52-pin) Pin No. C-4 Signal name I/O Pin No. Signal Name A1 NC A2 +3V_WLAN A3 NC A4 GND A5 BT_CTRL A6 +1.
C.10 J3G Table C-11 3G Connector pin assignments (52-pin) Pin No. Signal name I/O Pin No.
C.11 JLED Table C-14 LED/B Connector pin assignments (12-pin) Pin No. Signal name I/O Pin No. Signal Name 1 +5VALW 2 +5VS 3 DC_IN 4 PWR_ON_LED# 5 PWR_SUSP_LED# 6 BATT_FULL_LED# 7 BATT_LOW_LED# 8 HDD_LED 9 WIMAX_LED 10 WL_BT_LED# 11 MEDIA_LED 12 GND I/O C.12 JDDRL1 Table C-15 SODIMM I/F pin assignments (204-PIN) C-6 Pin No. Signal name I/O Pin No.
39 DDR_A_D16 I/O 40 DDR_A_D20 I/O 41 DDR_A_D17 I/O 42 DDR_A_D21 I/O 43 GND - 44 GND - 45 DDR_A_DQS#2 O 46 DDR_A_DM2 O 47 DDR_A_DQS2 O 48 GND - 49 GND - 50 DDR_A_D22 I/O 51 DDR_A_D18 I/O 52 DDR_A_D23 I/O 53 DDR_A_D19 I/O 54 GND - 55 GND - 56 DDR_A_D28 I/O 57 DDR_A_D24 I/O 58 DDR_A_D29 I/O 59 DDR_A_D25 I/O 60 GND - 61 GND - 62 DDR_A_DQS#3 O 63 DDR_A_DM3 O 64 DDR_A_DQS3 O 65 GND - 66 GND - 67 DDR_A_D26 I/O 68 DDR_A_D30 I/O
C-8 115 DDR_A_CAS# O 116 DDRA_ODT0 O 117 +1.5V - 118 +1.5V - 119 DDR_A_MA13 O 120 DDRA_ODT1 O 121 DDRA_SCS1# O 122 NC - 123 +1.5V - 124 +1.
189 GND - 190 GND - 191 DDR_A_D58 I/O 192 DDR_A_D62 I/O 193 DDR_A_D59 I/O 194 DDR_A_D63 I/O 195 GND - 196 GND - 197 GND - 198 PM_EXTTS# O 199 +3VS - 200 PM_SMBDATA I/O 201 GND - 202 PM_SMBCLK I/O 203 +0.75VS - 204 +0.75VS - C.13 JDDRH1 Table C-16 SODIMM I/F pin assignments (204-PIN) Pin No. Signal name I/O Pin No.
C-10 47 DDR_B_DQS2 O 48 GND - 49 GND - 50 DDR_B_D22 I/O 51 DDR_B_D18 I/O 52 DDR_B_D23 I/O 53 DDR_B_D19 I/O 54 GND - 55 GND - 56 DDR_B_D28 I/O 57 DDR_B_D24 I/O 58 DDR_B_D29 I/O 59 DDR_B_D25 I/O 60 GND - 61 GND - 62 DDR_B_DQS#3 O 63 DDR_B_DM3 O 64 DDR_B_DQS3 O 65 GND - 66 GND - 67 DDR_B_D26 I/O 68 DDR_B_D30 I/O 69 DDR_B_D27 I/O 70 DDR_B_D31 I/O 71 GND - 72 GND - 73 DDRB_CKE0 O 74 DDRB_CKE1 I/O 75 +1.5V - 76 +1.
123 +1.5V - 124 +1.
197 GND - 198 PM_EXTTS# O 199 +3VS - 200 PM_SMBDATA I/O 201 +3VS - 202 PM_SMBCLK I/O 203 +0.75VS - 204 +0.75VS - C.14 JKB Table C-17Keyboard Connector pin assignments (34-pin) Pin No. Signal name I/O Pin No.
9 GND 10 USB20_P0 11 USB20_N0 12 GND 13 NBA_PLUG 14 MIC_SENSE 15 GNDA 16 HP_R 17 HP_L 18 MIC1_R 19 MIC1_L 20 GNDA C.16 JREAD Table C-21 CARD READER connector pin assignments (46-pin) Pin No. Signal name I/O Pin No.
C.17 JGSIM Table C-22 JGSIM CARD connector pin assignments (10-pin) Pin No. Signal name I/O Pin No. Signal Name 1 +UIM_PWR 2 UIM_RESET 3 UIM_CLK 4 USB20_P10 5 GND 6 UIM_VPP 7 UIM_DATA 8 USB20_N10 9 NC 10 NC I/O C.18 JSPK Table C-23 SPK connector pin assignments (4-pin) Pin No. Signal name I/O Pin No. Signal Name 1 SPK_R1 2 SPK_R2 3 SPK_L1 4 SPK_L2 I/O C.19 JTP Table C-24 TP /B connector pin assignments (10-pin) Pin No. Signal name I/O Pin No.
3 GND - 4 GND - C.21 PJP2 Table C-29 11.6” Battery connector pin assignments (9-pin) Pin No. Signal name I/O Pin No. Signal Name I/O 1 BATT_S1 - 2 BATT_S1 - 3 BATT_P3 - 4 BATT_P4 - 5 BATT_P5 - 6 EC_SMDA I/O 7 EC_SMCA I/O 8 GND 9 GND - - C.22 PJP3 Table C-29 13” Battery connector pin assignments (9-pin) Pin No. Signal name I/O Pin No.
Appendix D Appendix D Keyboard Scan/Character Codes Table D-1 Scan codes (set 1 and set 2) (1/4) Code set 1 Cap No.
Table D-1 Scan codes (set 1 and set 2) (2/4) D-2 Code set 1 Cap No.
Table D-1 Scan codes (set 1 and set 2) (3/4) Code set 1 Cap No.
Table D-1 Scan codes (set 1 and set 2) (4/4) Cap No. Keytop Code set 1 Code set 2 122 F11 57 D7 78 F0 78 *3 123 F12 58 D8 07 F0 07 *3 124 PrintSc *6 *6 *6 *6 *6 126 Pause *7 *7 *7 *7 *7 X Fn — — — — *4 X Win E0 5B E0 DB E0 1F E0 F0 1F x App E0 5D E0 DD E0 2F E0 F0 2F Note Make Break Make Break Notes: 1. 2. 3. 4. 5. 6. 7. D-4 * * * * * * * Scan codes differ by mode. Scan codes differ by overlay function.
Table D-2 Scan codes with left Shift key Cap Key Code set 1 No.
Table D-3 Scan codes in Numlock mode Cap Key Code set 1 No.
Table D-5 Scan codes in overlay mode Cap No. Code set 1 Keytop Code set 2 Make Break Make Break 09 8 (8) 48 C8 75 F0 75 10 9 (9) 49 C9 7D F0 7D 11 P (*) 37 B7 7C F0 7C 23 U (4) 4B CB 6B F0 6B 24 I (5) 4C CC 73 F0 73 25 O (6) 4D CD 74 F0 74 26 ; (–) 4A CA 7B F0 7B 37 J (1) 4F CF 69 F0 69 38 K (2) 50 D0 72 F0 72 39 L (3) 51 D1 7A F0 7A 40 / (+) 4E CE 79 F0 79 52 M (0) 52 D2 70 F0 70 54 . (.
Table D-7 No.126 key scan code Key top Pause Shift Code set 1 Code set 2 Make Make Common E1 1D 45 E1 9D Ctrl E0 46 E0 C6 C5 E1 14 77 E1 F0 E0 7E E0 F0 7E 14 F0 77 *: This key generates only make codes.
Appendix E Key Layout 1. United Status (US) Keyboard Figure US keyboard 2. Traditional Chinese (CH) Keyboard Figure CH keyboard 3.
Figure TI keyboard 4. Korean (KO) Keyboard Figure KO keyboard 5.
Figure UK keyboard 6. US International (UI) Keyboard Figure UI keyboard 7.
Figure HB keyboard 8. Danish (DM) Keyboard Figure DM keyboard 9.
Figure SW keyboard 10. Arabic (ARE) Keyboard Figure ARE keyboard 11.
Figure CZ keyboard 12. Russian (RU) Keyboard Figure RU keyboard 13.
Figure PO keyboard 14. Slovakian (SL) Keyboard Figure SL keyboard 15.
Figure IT keyboard 16. French (FR) Keyboard Figure FR keyboard 17.
Figure GR keyboard 18. Greek (GK) Keyboard Figure GK keyboard 19.
Figure HG keyboard 20. Spanish (SP) Keyboard Figure SP keyboard 21.
Figure TR keyboard 22. Turkish F (TF-F) Keyboard Figure TF-F keyboard 23.
Figure SD keyboard 24. Belgian (BE) Keyboard Figure BE keyboard 25.
Figure YU keyboard 26. Norwegian (NW) Keyboard Figure NW keyboard 27.
Figure ND keyboard 28. Canadian Multinational (AC) Keyboard Figure AC keyboard 29.
Figure CB keyboard 30. Romania (RO) Keyboard Figure RO keyboard 31.
Figure BU keyboard 32. Japanese (JP) Keyboard Figure JP keyboard 32.
Figure LA keyboard Satellite/Satellite PRO T230/T230D Maintenance Manual E-17
F. Appendix F Series Screw Torque List (NDU10/11) Table F-1 Series Screw Torque List SCREW P/N SCREW SPEC Q'ty SCREW TORQUE LOCATION LCD ASSY MA000007GG0 MACA25001G0 MMCK20060G0 M2x3 (NI 白 鎳) M2x4 (ZK 黑 鋅) M2x6 (ZK 黑 鋅) 6 LCD HINGE BRK ASSY L&R TO LCD PANEL 1.2~1.5Kgf.cm 13.1" 6 LCD HINGE L&R TO LCD COVER 1.5~2.0Kgf.cm 2 LCD BEZEL TO COVER 1.5~2.0Kgf.cm MB MAA000012G0 MAA000012G0 MA000007GG0 M2x5 (NI 白 鎳) M2x5 (NI 白 鎳) M2x3 (NI 白 鎳) 2 HDD(H=10.2mm) 1.5~2.0Kgf.
MA000007GG0 M2x3 (NI 白 鎳) 2 HDD BOARD TO LOW 1.2~1.5Kgf.cm LOGIC ASSY MA000007GG0 MMCK20060G0 MMCK20060G0 MA000007GG0 MMCK20060G0 MMCK20060G0 MMCK20060G0 MA000007GG0 MA0000049G0 F-2 M2x3 (NI 白 鎳) M2x6 (ZK 黑 鋅) M2x6 (ZK 黑 鋅) M2x3 (NI 白 鎳) M2x6 (ZK 黑 鋅) M2x6 (ZK 黑 鋅) M2x6 (ZK 黑 鋅) M2x3 (NI 白 鎳) M2*4.5 半 牙 (ZK 黑鋅) 5 MB TO LOG LOW 1.2~1.5Kgf.cm 2 LCD HINGE R TO LOW 1.5~2.0Kgf.cm 2 LCD HINGE L TO LOW 1.5~2.0Kgf.cm 4 LOG UP TO LOG LOW 1.2~1.5Kgf.cm (KB AREA) 1 LOG UP TO LOG LOW 1.5~2.
Appendix G Appendix G Reliability The following table shows MTBF (Mean Time Between Failures) for each component.
