User’s Manual U200
Copyright © 2006 by TOSHIBA Corporation. All rights reserved. Under the copyright laws, this manual cannot be reproduced in any form without the prior written permission of TOSHIBA. No patent liability is assumed, with respect to the use of the information contained herein.
Trademarks IBM is a registered trademark and IBM PC is a trademark of International Business Machines Corporation. Intel, Intel SpeedStep, Intel Core, Celeron and Centrino are trademarks or registered trademarks of Intel Corporation. Windows and Microsoft are registered trademarks of Microsoft Corporation. Photo CD is a trademark of Eastman Kodak. Sonic RecordNow! is a registered trademark of Sonic Solutions. Bluetooth is a trademark owned by its proprietor and used by TOSHIBA under license. i.
Working environment This product was designed to fulfill the EMC (Electromagnetic Compatibility) requirements for “residential, commercial and light industry environments”. The following environments are not approved: ■ Industrial Environments (e.g.
Modem warning notice Conformity Statement The equipment has been approved to [Commission Decision “CTR21”] for pan-European single terminal connection to the Public Switched Telephone Network (PSTN). However, due to differences between the individual PSTNs provided in different countries/regions the approval does not, of itself, give an unconditional assurance of successful operation on every PSTN network termination point.
Optical disc drive safety instructions Be sure to check the international precautions at the end of this section. Panasonic Communications DVD-ROM & CD-R/RW drive UJDA765 ■ The DVD-ROM & CD-R/RW drive UJDA765 employs a laser system. To ensure proper use of this product, please read this instruction manual carefully and retain for future reference. Should the unit ever require maintenance, contact an authorized service location.
DVD Super Multi with Double Layer Recording UJ-842 ■ The DVD Super Multi drive with Double Layer Recording model employs a laser system. To ensure proper use of this product, please read this instruction manual carefully and retain for future reference. Should the unit ever require maintenance, contact an authorized service location. ■ Use of controls, adjustments or the performance of procedures other than those specified may result in hazardous radiation exposure.
International precautions CAUTION: This appliance contains a laser system and is classified as a “CLASS 1 LASER PRODUCT.” To use this model properly, read the instruction manual carefully and keep this manual for your future reference. In case of any trouble with this model, please contact your nearest “AUTHORIZED service station.” To prevent direct exposure to the laser beam, do not try to open the enclosure.
OBS! Apparaten innehåller laserkomponent som avger laserstråining överstigande gränsen för laserklass 1. VAROITUS. Suojakoteloa si saa avata. Laite sisältää laserdiodin, joka lähetää näkymätöntä silmilie vaarallista lasersäteilyä. CAUTION: USE OF CONTROLS OR ADJUSTMENTS OR PERFORMANCE OF PROCEDURES OTHER THAN THOSE SPECIFIED IN THE OWNER’S MANUAL MAY RESULT IN HAZARDOUS RADIATION EXPOSURE.
x User’s Manual
Table of Contents Preface General Precautions Chapter 1 Introduction Equipment checklist. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-1 Features. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-4 Special features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-11 Utilities. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-13 Options . . . .
Chapter 4 Operating Basics Using the Touch Pad . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4-1 Using the Fingerprint Sensor (provided with some models) . . . . . . .4-2 Front operation buttons. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4-8 Using the USB floppy disk drive (optional) . . . . . . . . . . . . . . . . . . . .4-10 Using optical disc drives . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Chapter 8 Optional Devices PC card . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-2 Bridge media slot . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-3 Memory expansion . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-10 Battery Pack . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-15 Universal AC Adaptor . . . . . . . . . . . . . . . . . . . . . .
xiv User’s Manual
Preface Congratulations on your purchase of the U200 computer. This powerful notebook computer provides excellent expansion capability, including multimedia devices, and it is designed to provide years of reliable, high-performance computing. This manual tells how to set up and begin using your U200 computer. It also provides detailed information on configuring your computer, basic operations and care, using optional devices and troubleshooting.
Preface Chapter 7, HW Setup, explains how to configure the computer using the HW Setup program and TPM (optional). Chapter 8, Optional Devices, describes the optional hardware available. Chapter 9, Troubleshooting, provides helpful information on how to perform some diagnostic tests, and suggests courses of action if the computer doesn’t seem to be working properly. Chapter 10, Legal Footnotes, provides Legal Footnote information related to your computer.
Preface Display S ABC Names of windows or icons or text generated by the computer that appear on its display screen are presented in the type face you see to the left. Messages Messages are used in this manual to bring important information to your attention. Each type of message is identified as shown below. Pay attention! A caution informs you that improper use of equipment or failure to follow instructions may cause data loss or damage your equipment. Please read.
Preface xviii User’s Manual
General Precautions TOSHIBA computers are designed to optimize safety, minimize strain and withstand the rigors of portability. However, certain precautions should be observed to further reduce the risk of personal injury or damage to the computer. Be certain to read the general precautions below and to note the cautions included in the text of the manual. Stress injury Carefully read the Instruction Manual for Safety & Comfort.
General Precautions PC card overheating Some PC cards can become hot with prolonged use. Overheating of a PC card can result in errors or instability in the PC card operation. Also be careful when you remove a PC card that has been used for a long time. Mobile phone Use of mobile phone can interfere with the audio system. Computer operation is not impaired but it is recommended that a distance of 30 cm be maintained between the computer and a mobile phone in use.
Chapter 1 Introduction This chapter provides an equipment checklist, and it identifies the computer’s features, options and accessories. Some of the features described in this manual may not function properly if you use an operating system that was not preinstalled by TOSHIBA. Equipment checklist Carefully unpack your computer. Save the box and packing materials for future use.
Introduction Software Microsoft® Windows XP Professional ■ The following software is preinstalled: ■ Microsoft® Windows XP Professional ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ Microsoft® Internet Explorer TOSHIBA Utilities TOSHIBA SD Memory Boot Utility DVD Video Player InterVideo WinDVD Creator Fingerprint Utility (provided with some models) RecordNow! Basic for TOSHIBA (preinstalled with some models) DLA for TOSHIBA (preinstalled with some models) TOSHIBA Power Saver TOSHIBA ConfigFree TOSHIBA Assis
Introduction Microsoft® Windows XP Home Edition ■ The following software is preinstalled: ■ Microsoft® Windows XP Home Edition ■ Microsoft® Internet Explorer ■ TOSHIBA Utilities ■ TOSHIBA SD Memory Boot Utility ■ DVD Video Player ■ InterVideo WinDVD Creator ■ Fingerprint Utility (provided with some models) ■ TOSHIBA Disc Creator (preinstalled with some models) ■ TOSHIBA Direct Disc Writer (preinstalled with some models) ■ TOSHIBA Power Saver ■ TOSHIBA ConfigFree ■ TOSHIBA Assist ■ TOSHIBA Controls ■ TOSHIB
Introduction Features The computer uses TOSHIBA’s advanced Large Scale Integration (LSI), Complementary Metal-Oxide Semiconductor (CMOS) technology extensively to provide compact size, minimum weight, low power usage, and high reliability. This computer incorporates the following features and benefits: Processor Built-in The computer is equipped with one of the following Intel® processors. ■ Intel® Core™ Duo processor, which incorporates a 2MB level 2 cache memory.
Introduction Memory Slots 256, 512, 1,024 or 2,048 MB memory modules can be installed in the two memory slots for a maximum of 4,096 MB (Intel® 945GM model) or a maximum of 2,048 MB (Intel® 940GML model) system memory. Legal Footnote (Memory (Main System))*2 For more information on the Legal Footnote regarding Memory (Main System), please refer to the Legal Footnotes section in Chapter 10. Click the *2. Video RAM 128 MB of RAM is provided for video display.
Introduction Disks Hard disk drive Available in five sizes. ■ 40.0 billion bytes (37.26 GB) ■ 60.0 billion bytes (55.89 GB) ■ 80.0 billion bytes (74.53 GB) ■ 100.0 billion bytes (93.16 GB) ■ 120.0 billion bytes (111.79 GB) Part of the space on the hard disk drive is reserved as administration space. Legal Footnote (Hard Disk Drive (HDD) Capacity)*4 For more information on the Legal Footnote regarding Hard Disk Drive (HDD) Capacity, please refer to the Legal Footnotes section in Chapter 10. Click the *4.
Introduction DVD Super Multi drive Double Layer Some models are equipped with a full-size DVD Super Multi drive module that lets you record data to rewritable CD/DVDs as well as run either 12cm (4.72") or 8cm (3.15") CD/DVDs without using an adaptor. It reads DVD-ROMs at maximum 8 speed and CD-ROMs at maximum 24 speed. It writes CD-R at up to 24 speed, CD-RW at up to 16 speed, DVD-R and DVD+R at up to 8 speed, DVD-RW and DVD+RW at up to 4 speed, DVD-R DL at up to 2 speed, DVD+R DL at up to 2.
Introduction Keyboard Built-in 84 keys or 85 keys, compatible with IBM® enhanced keyboard, embedded numeric overlay, dedicated cursor control, and keys. Refer to Chapter 5, The Keyboard, for details. Pointing Device Built-in Touch Pad A Touch Pad and control buttons in the palm rest enable control of the on-screen pointer and scrolling of windows. Ports External monitor Analog VGA port supports VESA DDC2B compatible functions. Universal Serial Bus (USB 2.
Introduction Communications User’s Manual Modem An internal modem provides capability for data and fax communication supporting the V.90 (V.92) standards. The speed of data transfer and fax depends on analog telephone line conditions. It has a modem jack for connecting to a telephone line. Both the V.90 and V.92 standards are supported only in the USA, Canada, UK, France, Germany and Australia. Only V.90 is available in other regions.
Introduction Wireless LAN Some computers in this series are equipped with a Wireless LAN card that is compatible with other LAN systems based on Direct Sequence Spread Spectrum/Orthogonal Frequency Division Multiplexing radio technology that complies with the IEEE 802.11 Standard (Revision A, B or G). ■ Theoretical maximum speed: 54Mbps (IEEE802.11a, 802.11g) ■ Theoretical maximum speed: 11Mbps (IEEE802.11b) ■ Frequency Channel Selection (5 GHz: Revision A / 2.
Introduction Security Security lock slot Allows the connection of a security lock to anchor the computer to a desk or other large object. Special features The following features are either unique to TOSHIBA computers or are advanced features, which make the computer more convenient to use. User’s Manual Front operation buttons These buttons (Internet, CD/DVD, Play/Pause, Stop, Previous, Next.) allow you to manage Audio/Video and run applications. These buttons are provided with some models.
Introduction 1-12 Keypad overlay A ten-key pad is integrated into the keyboard. Refer to the Keypad overlay section in Chapter 5, The Keyboard, for instructions on using the keypad overlay. Power on password Two levels of password security, supervisor and user, are available to prevent unauthorized access to your computer. Instant security A hot key function blanks the LCD screen and disables the computer providing data security.
Introduction HDD Protection (preinstalled with some models) Using the acceleration sensor built in the computer, the HDD Protection function detects vibration, shocks, and other such occurrences in the computer, and automatically moves the HDD (Hard Disk Drive) head to the safe position to reduce the risk of damage that could be caused to the disk by head-to-disk contact.
Introduction TOSHIBA Controls This utility lets you assign applications or functions to the built-in buttons. To access this utility, click start, point to Control Panel, choose Printers and Other Hardware and click the Toshiba Controls icon. Fingerprint Utility (provided with some models) This product has a Fingerprint Utility installed for the purpose of enrolling and recognizing fingerprints.
Introduction TOSHIBA SD Memory Boot Utility The TOSHIBA SD memory boot utility allows you to create a bootable SD memory card to start the system. You can access TOSHIBA SD Memory Boot Utility from the menu bar as follows. Click start, point to All Programs, point to TOSHIBA, point to Utilities and click SD Memory Boot Utility. TOSHIBA Zooming Utility This utility allows you to enlarge or reduce the icon size on the desktop or the application window.
Introduction 1-16 TOSHIBA TouchPad On/Off Utility This utility allows you to disable/enable the Touch Pad using the Fn + F9 Hot key. TOSHIBA Mic Effect The TOSHIBA Mic Effect utility provides you with Echo Canceller and Microphone Array functions. The echo cancellation function removes or reduces any harsh echoes or howling sounds that occur when playing audio sounds recorded with a microphone through the speakers.
Introduction DLA for TOSHIBA (preinstalled with some models) DLA (Drive Letter Access) is a packet writing software which allows you to write files and/or folders to DVD-RW, CD-RW and DVD+RW discs via a drive letter like a floppy disk or other removable disks. This function is only in Windows XP Professional model.
Introduction 1-18 Universal AC Adaptor If you use your computer at more than one site frequently, it may be convenient to purchase an additional AC adaptor for each site so you will not have to carry the adaptor with you. Battery Charger The battery charger lets you charge extra batteries outside the computer. USB FDD Kit The USB floppy disk drive accommodates either 3 1/2" 1.44-megabyte or 720-kilobyte floppy disks through connection to a USB port.
Chapter 2 The Grand Tour This chapter identifies the various components of your computer. Become familiar with each component before you operate the computer. Legal Footnote (Non-applicable Icons)*8 For more information on the Legal Footnote regarding Non-applicable Icons, please refer to the Legal Footnotes section in Chapter 10. Click the *8. Front with the display closed The following figure shows the computer’s front with its LCD display panel in the closed position.
The Grand Tour i.LINK (IEEE1394) port This port allows you to connect an external device, such as a digital video camera for high-speed data transfer. Microphone A built-in microphone lets you record sound into your applications. Refer to the Sound system section in Chapter 4, Operating Basics. Microphone jack A 3.5 mm mini microphone jack enables connection of a three-conductor mini jack for monaural microphone input. Headphone jack A 3.
The Grand Tour ■ Do not connect any cable other than a LAN cable to the LAN jack. It could cause damage or malfunction. ■ Do not connect the LAN cable to a power supply. It could cause damage or malfunction. Link indicator (green) This indicator glows green when the computer is connected to a LAN and the LAN is functioning properly. LAN active indicator (orange) This indicator glows orange when data is being exchanged between the computer and the LAN.
The Grand Tour ■ Connection to any communication line other than an analog phone line could cause a PC system failure. ■ Connect the built-in modem only to ordinary analog phone lines. ■ Never connect the built-in modem to a digital line (ISDN). ■ Never connect the built-in modem to the digital connector on a public telephone or to a digital private branch exchange (PBX). ■ Never connect the built-in modem to a key telephone system for residences or offices.
The Grand Tour Volume control Use this dial to adjust the volume of the stereo speakers and the stereo headphones. Move the Volume control to the right to increase the volume and to the left to decrease the volume. To mute the sound press the Fn + Esc keys. Refer to the Hot keys section in Chapter 5, The Keyboard, for details on the Fn + Esc keys. Bridge media slot This slot lets you insert an SD card (SDIO), Memory Stick (Pro), xD picture card and MultiMediaCard. Refer to Chapter 8, Optional Devices.
The Grand Tour Back side The following figure shows the computer’s back side. Battery pack The back side of the computer Battery pack The battery pack powers the computer when the AC adaptor is not connected. For detailed information on the battery pack, refer to Chapter 6, Power and Power-Up Modes. Underside The following figure shows the underside of the computer. Make sure the display is closed before turning over your computer.
The Grand Tour Front with the display open This section shows the computer with the LCD display panel open. Refer to the appropriate illustration for details. To open the display, slide the display latch on the front of the LCD display panel and lift up. Position the LCD display panel at a comfortable viewing angle.
The Grand Tour Touch Pad A Touch Pad located in the center of the palm rest is used to control the on-screen pointer. Refer to the Using the Touch Pad section in Chapter 4, Operating Basics. Fingerprint Sensor (provided with some models) Just by swiping the finger against the fingerprint sensor, the following functions will be enabled: ■ Logon to Windows and access a security-enabled homepage through IE (Internet Explorer).
The Grand Tour System indicators LEDs above the icons, light when various computer operations are in progress. System indicators User’s Manual DC IN The DC IN indicator glows blue when DC power is supplied from the AC power adaptor. If the adaptor’s output voltage is abnormal or if the power supply malfunctions, this indicator flashes orange. Power The Power indicator glows blue when the computer is on.
The Grand Tour Keyboard indicators The figures below show the positions of the keypad overlay indicators and the Caps Lock indicator. When the Arrow mode indicator glows the keypad overlay lets you control the cursor. When the Numeric mode indicator glows the keypad overlay lets you enter numbers. When the Caps Lock indicator glows the keyboard is in all-caps mode. Caps Lock indicator Caps Lock indicator Caps Lock This indicator glows green when the alphabet keys are locked in uppercase.
The Grand Tour USB floppy disk drive (optional) The USB floppy disk drive accommodates 1.44-megabyte or 720-kilobyte floppy disks and connects to the USB port. It is supplied as standard with some models and as an option with others. USB connector Disk-In-Use Indicator Floppy disk slot Eject button USB floppy disk drive USB connector Insert this connector into one of the USB ports of your computer. Disk-In-Use Indicator This indicator lights when the floppy disk is being accessed.
The Grand Tour Optical disc drives One of the following optical disc drives is installed in the computer: DVD-ROM&CD-R/RW and DVD Super Multi drives. An ATAPI interface controller is used for CD/DVD-ROM operation. When the computer is accessing a CD/DVD, an indicator on the drive glows. For information on loading and unloading discs refer to the Using optical disc drive section in Chapter 4, Operating Basics.
The Grand Tour Formats The drives support the following formats: ■ ■ ■ ■ ■ ■ ■ ■ CD-ROM DVD-ROM CD-DA Photo CD™ (single/multi-session) CD-ROM XA Mode 2 (Form1, Form2) DVD-R DL (Format 1) DVD+R DL DVD-RAM ■ ■ ■ ■ ■ ■ ■ ■ ■ DVD -Video CD-Text CD-ROM Mode 1, Mode 2 Enhanced CD (CD-EXTRA) Addressing Method 2 DVD-R DVD-RW DVD+R DVD+RW DVD-ROM&CD-R/RW drive The full-size DVD-ROM&CD-R/RW drive module lets you record data to rewritable CDs as well as run either 12 cm (4.72") or 8 cm (3.
The Grand Tour AC adaptor The AC adaptor can automatically adjust to any voltage ranging from 100 to 240 volts and to a frequency of either 50 or 60 hertz, enabling you to use this computer in almost any country/region. The adaptor converts AC power to DC power and reduces the voltage supplied to this computer. To recharge the battery, simply connect the AC adaptor to a power source and the computer. Refer to Chapter 6, Power and Power-Up Modes for details.
Chapter 3 Getting Started This chapter provides basic information to get you started using your computer. It covers the following topics: ■ Setting up your work space - for your health and safety Be sure also to read the Instruction Manual for Safety & Comfort. This guide, which is included with the computer, explains product liability.
Getting Started General conditions In general, if you are comfortable, so is your computer, but read the following to make sure your work site provides a proper environment. ■ Select a work area that has: ■ a well-designed and functioning ventilation system that does not forcefully direct air on you ■ good air circulation ■ a comfortable ambient temperature and relative humidity.
Getting Started ■ Leave ample ventilation room for the fan. Do not block the vents. ■ If the PC interferes with radio equipment, turn the PC power off immediately. Such interference could cause equipment malfunction. ■ Never place your PC on a shaky table, uneven, tilted surface or other unstable location. Your PC may fall, causing damage to the PC or possibly injury. ■ Never leave the power to your PC on continuously for more than 24 hours. Turn the power off when this product is not in use.
Getting Started Seating and posture Maintain a comfortable working posture when using your PC where your body joints are naturally aligned to reduce stress on different parts of your body. Consider the following: Below eye level 90°angles Foot rest Posture and positioning of the computer ■ Keep hands, wrists, and forearms straight, in-line and roughly parallel to the floor. ■ Keep head level, or bent slightly forward, forward facing, and balanced. Generally the head is in-line with the torso.
Getting Started Lighting Select the right level of illumination and place your PC appropriately to minimize glare from overhead lights, desk lamps and windows. Glare on the LCD or monitor may cause eye strain, eye fatigue or headaches. Consider the following suggestions regarding lighting your work environment: ■ Position the PC so that the light source does not shine or reflect directly onto the display or shine or reflect directly into the eyes of the user.
Getting Started Strategic Rest Breaks Take short, strategically spaced rest breaks to avoid eye strain and body discomforts. For more specific recommendations on the safety and comfort of your computer environment, customers in the United States may visit the United States Department of Labor, Occupational Safety & Health Administration website at: http://www.osha.gov/SLTC/etools/computerworkstations/ Other Things to Note ■ Never turn off the power while an application is running.
Getting Started ■ Always use the Toshiba AC adaptor that was provided with your PC and the Toshiba Battery Charger (that may have been provided with your PC), or use Toshiba recommended alternate models to avoid any risk of fire or other damage to the PC. Use of an incompatible AC adaptor or Battery Charger could cause fire or damage to the PC possibly resulting in serious injury. ■ Use only the AC adaptor supplied with your computer or an equivalent adaptor that is compatible.
Getting Started Connecting the power cord to the AC adaptor (3-pin plug) Depending on the model, a 2-pin or 3-pin plug set of the above may be bundled. 2. Connect the AC adaptor’s DC output plug to the DC IN 15V jack on the left side of the computer. DC IN 15V jack Connecting the adaptor to the computer 3. Plug the power cord into a live wall outlet. The Battery and DC IN indicators on the front of the computer should glow.
Getting Started 2. While holding down the palm rest with one hand so that the main body is not raised, lift the panel slowly. Adjust the angle of the panel to provide optimal clarity. Be careful not to open the display panel too far as this could put stress on the display panel’s hinges and cause damage. Use reasonable care when opening and closing the LCD display panel. Opening it vigorously or slamming it shut could damage the computer.
Getting Started Starting up for the first time When you first turn on the power, the computer’s initial screen is the Microsoft Windows XP Startup Screen Logo. Follow the on-screen directions for each screen. During setup, you can click the Back button to return to the previous screen. Be sure to read the Windows End User License Agreement display carefully. Turning off the power The power can be turned off in one of the following modes: Shut down (Boot), Hibernation or Standby Mode.
Getting Started ■ When the AC adaptor is connected, the computer will go into Standby Mode according to the settings in the TOSHIBA Power Saver utility. ■ To restore operation from Standby Mode, press the power button or press any key. The latter action only works on the internal keyboard if the Wake-up on Keyboard option is enabled in HW Setup.
Getting Started 3. Press the power button. This feature must be enabled. Refer to the Setup Actions tab in TOSHIBA Power Saver Utility described in the Control Panel. Open Performance and Maintenance and open TOSHIBA Power Saver. When you turn the power back on, you can continue where you left when you shut down the computer. ■ When the computer is shut down in Standby Mode, the power indicator blinking orange.
Getting Started ■ Saves power by shutting down the system when the computer receives no input or hardware access for the duration set by the System hibernate feature. ■ You can use the panel power off feature. Starting Hibernation Mode You can also enable Hibernation Mode by pressing Fn + F4. Refer to Chapter 5, The Keyboard, for details. To enter Hibernation Mode, follow the steps below. 1. Click start. 2. Select Turn Off Computer. 3. Open the Turn Off Computer dialog box. 4. Click Hibernate.
Getting Started Restarting the computer Certain conditions require that you reset the system. For example, if: ■ You change certain computer settings. ■ An error occurs and the computer does not respond to your keyboard commands. ■ There are three ways to reset the computer system: 1. Click start then click Turn off computer. From the Turn off computer menu select Restart. 2. Press Ctrl + Alt + Del to display the Windows Task Manager, then select Shut Down and Restart. 3.
Getting Started Restoring Express Media Player (preinstalled with some models) Please use the Express Media Player Recovery CD to reinstall the “Express Media Player” before you reinstall a Windows® operating system. (Depends on configuration) To restore Express Media Player, follow the steps below. 1. Load the Express Media Player Recovery CD in the optical media drive and turn off the computer’s power. 2. Hold down the F12 key and turn on the power.
Getting Started 3-16 User’s Manual
Chapter 4 Operating Basics This chapter describes the basic operations of your computer and precautions when using it, as well as the handling of CD/DVD. Using the Touch Pad To use the Touch Pad, simply touch and move your fingertip across it in the direction you want the on-screen pointer to go. Fingerprint Sensor Touch Pad Touch Pad control buttons Touch Pad and Touch Pad control buttons Two buttons below the Touch Pad are used like the buttons on a mouse pointer.
Operating Basics You can also tap the Touch Pad to perform functions similar to those of the left button. Click: Tap once Double-click: Tap twice Drag and drop: Tap to select the material you want to move. Leave your finger on the Touch Pad after the second tap and move the material. Using the Fingerprint Sensor (provided with some models) This product has a Fingerprint Utility installed for the purpose of enrolling and recognizing fingerprints.
Operating Basics Observe the following before you place your finger on the sensor whether for fingerprint enrollment/registration or recognition. ■ Wash and dry your hands thoroughly. ■ Remove static electricity from your fingers by touching any metal surface. Static electricity is a common cause of sensor failures, especially when the weather is dry. ■ Clean the sensor with a lint-free cloth. Do not use detergent to clean the sensor.
Operating Basics Fingerprint Sensor Limitations. ■ The fingerprint sensor compares and analyzes the unique characteristics in a fingerprint. ■ A warning message will be displayed when recognition is abnormal or recognition is not successful within a fixed duration. ■ The recognition success rate may differ from user to user. ■ Toshiba does not guarantee that this fingerprint recognition technology will be error-free.
Operating Basics Set Up Procedure Please use the following procedure when first using fingerprint authentication. Fingerprint Registration Enroll the required authentication data using the User Enrollment Wizard. ■ The fingerprint authentication uses the same Windows logon ID and password. If the Windows logon password has not been setup, please do so before registration. ■ Up to 21 fingerprint patterns can be registered on this sensor. 1.
Operating Basics Window Logon via Fingerprint Authentication In place of the usual Windows logon by ID and password, fingerprint authentication also allows logon to Windows. This is useful especially when many users are using the same computer as it allows the user selection screen to be skipped. Fingerprint Authentication Procedure 1. Start up the computer. 2. The Logon Authorization screen is displayed. Choose any of the enrolled fingers and swipe the fingerprint on the sensor.
Operating Basics How to Enable Fingerprint Power-on Security Settings It is necessary to first enroll your fingerprint with the Protector Suite QL application prior to enabling and configuring the Fingerprint Power-on Security System. Check that your fingerprint is enrolled before configuring the settings. See Manual for Fingerprint Registration/Enrollment instructions. 1. Swipe your finger across the Fingerprint Sensor. 2. MENU appears in the lower right corner of the screen.
Operating Basics Fingerprint Utility limitations TOSHIBA does not guarantee that the Fingerprint Utility technology will be completely secure or error-free. TOSHIBA does not guarantee that the Fingerprint Utility will accurately screen out unauthorized users at all times. TOSHIBA is not liable for any failure or damage that might arise out of the use of the fingerprint software or utility.
Operating Basics User’s Manual Internet button Press this button to launch an Internet browser. If the computer’s power is off, you can press this button to turn on the computer’s power and launch the browser automatically in one step. CD/DVD button Pressing this button will launch an application program that allows for watching CD/DVD.
Operating Basics Using the USB floppy disk drive (optional) An optional USB floppy disk drive accommodates 1.44-megabyte or 720-kilobyte floppy disks and connects to the USB port. Refer to Chapter 2, The Grand Tour, for more information. It is supplied as standard with some models and as an option with others. Connecting the USB floppy disk drive To connect the drive, plug the floppy disk drive’s USB connector into a computer’s USB port. Make sure the USB connector is properly aligned with the socket.
Operating Basics Using optical disc drives The full-size drive provides high-performance execution of CD/DVD-ROM-based programs. You can run either 12 cm (4.72") or 8 cm (3.15") CD/DVDs without an adaptor. An ATAPI interface controller is used for CD/DVD-ROM operation. When the computer is accessing a CD/DVD-ROM, an indicator on the drive glows. Use the WinDVD application to view DVD-Video discs.
Operating Basics 3. Lay the CD/DVD, label side up, in the disc tray. Laser lens Inserting a CD/DVD When the disc tray is fully opened, the edge of the computer will extend slightly over the CD/DVD tray. Therefore, you will need to turn the CD/DVD at an angle when you place it in the disc tray. After seating the CD/DVD, however, make sure it lies flat, as shown in figure 4-8. ■ Do not touch a laser lens and its circumference portion. Doing so could cause misalignment.
Operating Basics 5. Push the center of the disc tray to close it. Press gently until it locks into place. If the CD/DVD is not seated properly when the disc tray is closed, the CD/DVD might be damaged. Also, the disc tray might not open fully when you press the eject button. Closing the CD/DVD disc tray Removing discs To remove the CD/DVD, follow the steps below. Do not press the eject button while the computer is accessing the media drive.
Operating Basics 2. The CD/DVD extends slightly over the sides of the disc tray so you can hold it. Hold the CD/DVD gently and lift it out. Removing a CD/DVD 3. Push the center of the disc tray to close it. Press gently until it locks into place. How to remove CD/DVD when the disc tray will not open Pressing the eject button will not open the disc tray when the computer power is off.
Operating Basics Writing CDs on DVD-ROM&CD-R/RW drive Depending on the type of drive installed, you may be able to write CDs. The DVD-ROM&CD-R/RW drive lets you write as well as read CD-ROMs. Observe the precautions in this section to ensure the best performance for writing CDs. For information on loading and unloading CDs refer to the Using optical disc drives section. ■ Refer to the Writable discs section in Chapter 2 for details about the types of writable CD/DVD discs.
Operating Basics ■ Do not write while virus check software is running. Wait for it to finish, then disable virus detection programs including any software that checks files automatically in the background. ■ Do not use hard disk utilities, including those intended to enhance hard disk drive access speeds. They may cause unstable operation and damage data. ■ Write from the computer’s hard disk drive to the CD. Do not try to write from shared devices such as a LAN server or any other network device.
Operating Basics Writing CD/DVDs on DVD Super Multi drive You can use the DVD Super Multi drive to write data to either CD-R/RW or DVD-R/-R DL/-RW/+R/+R DL/+RW/-RAM discs. The TOSHIBA Disc Creator (optional), the TOSHIBA Direct Disc Writer (optional), the RecordNow! Basic for TOSHIBA (optional) and the DLA for TOSHIBA (optional) are provided for writing. ■ Refer to the Writable discs section in Chapter 2 for details about the types of writable CD/DVD discs.
Operating Basics Before writing or rewriting ■ Based on TOSHIBA’s limited compatibility testing, we suggest the following manufacturers of CD-R/RW and DVD-R/-R DL/+R/+R DL/-RW/+RW/-RAM disc. However, in no event does TOSHIBA guarantee the operation, quality or performance of any disc. Disc quality can affect write or rewrite success rates. CD-R: TAIYO YUDEN CO., LTD. MITSUBISHI CHEMICAL CORPORATION RICOH Co., Ltd. CD-RW: (Multi-Speed and High-Speed) MITSUBISHI CHEMICAL CORPORATION RICOH Co., Ltd.
Operating Basics This drive cannot use discs that allow writing faster than 16 speed (DVD-R, DVD+R), 6 speed (DVD-RW), 4 speed (DVD+RW), 5 speed (DVD-RAM), 4 speed (DVD-R DL, Double Layer supported model only), 8 speed (DVD+R DL, Double Layer supported model only). ■ If the disc is poor in quality, dirty or damaged, writing or rewriting errors may occur. Be careful to check the disc for dirt or damage before you use it.
Operating Basics ■ Do not write while a virus check software is running. Wait for it to finish and then disable virus detection programs including any software that checks files automatically in the background. ■ Do not use hard disk utilities, including those intended to enhance hard disk drive access speed. They may cause unstable operation and data damage. ■ CD-RW (Ultra Speed +) media is not supported. If used, data may be lost or damaged. ■ Write from the computer’s hard disk drive to the CD/DVD.
Operating Basics RecordNow! Basic for TOSHIBA (preinstalled with some models) This function is only in Windows XP Professional model. Note the following limitations when you use RecordNow!: ■ DVD-Video cannot be created using RecordNow!. ■ DVD-Audio cannot be created using RecordNow!. ■ You cannot use RecordNow!’s “Audio CD for Car or Home CD Player” function to record music to the DVD-R/-R DL/-RW or DVD+R/+R DL/+RW discs.
Operating Basics TOSHIBA Disc Creator(preinstalled with some models) This function is only in Windows XP Home Edition model. Note the following limitations when you use TOSHIBA Disc Creator: ■ DVD-Video cannot be created using TOSHIBA Disc Creator. ■ DVD-Audio cannot be created using TOSHIBA Disc Creator. ■ You cannot use TOSHIBA Disc Creator’s “Audio” function to record music to the DVD-R/-R DL/-RW or DVD+R/+R DL/+RW discs.
Operating Basics Data Verification To verify that data is written or rewritten correctly, follow the steps below before you write or rewrite a Data CD/DVD. 1. Display the setting dialog box by one of the following two steps: 2. Click the setting button ( 3. 4. 5. 6. ) for writing on the main toolbar in the Data CD/DVD mode. Select Setting for writing -> Data CD/DVD in the Setting menu. Mark the Verify written data check box. Select File Open or Full Compare mode. Click the OK button.
Operating Basics TOSHIBA Direct Disc Writer (preinstalled with some models) This function is only in Windows XP Home Edition model. Note the following limitations when you use TOSHIBA Direct Disc Writer: ■ This software supports only rewritable discs (DVD+RW, DVD-RW, and CD-RW). It does not support DVD+R/+R DL, DVD-R/-R DL, and CD-R discs that are not rewritable.
Operating Basics How to make a DVD-Video Simplified steps for making a DVD-Video from video data captured from a DV-Camcorder: 1. Click Start -> All Programs -> InterVideo WinDVD Creator2 -> InterVideo WinDVD Creator to launch WinDVD Creator. 2. Click Capture button then capture the video data from the DV-> Camcorder via IEEE1394. 3. Click Edit button then drag the video clips from Video Library tab to the edit track. 4. Click Make Movie button in the top bar. 5.
Operating Basics ■ While recording video to DVD or tape, please close all other programs. ■ Do not run software like a screen saver because it can put a heavy load on the CPU. ■ Do not run communication applications like a modem or a LAN. 2. Before recording the video to DVD ■ When you record to DVD discs, please use only media recommended by TOSHIBA. ■ Do not set the working drive to a slow device like a USB 1.1 hard disk drive or it will fail to write the DVD.
Operating Basics 4. About recorded DVDs ■ Some DVD-ROM drives for personal computers or other DVD players may not be able to read DVD-R/+R/-R DL/+R DL/-RW/+RW/-RAM discs. ■ When playing your recorded disc on your computer, please use the WinDVD software application. ■ If you use an over-used rewritable disc, the full formatting might be locked. Please use a brand new disc. Media care This section provides tips on protecting data stored on your CD/DVDs and floppy disks. Handle your media with care.
Operating Basics 5. Never put a floppy disk in a location where water or other liquid may contact it or where it is excessively damp. It could cause data loss. Never use a wet or damp floppy disk. It could damage the floppy disk drive or other devices. 6. Data may be lost if the floppy disk is twisted, bent, or exposed to direct sunlight, extreme heat or cold. 7. Do not place heavy objects on your floppy disks. 8. Do not eat, smoke, or use erasers near your floppy disks.
Operating Basics SoundMAX control panel The SoundMAX control panel lets you control additional functions for the Microphone Enhancement and Audio Power Management. To launch the SoundMAX Control Panel, follow the steps below. 1. Click start and click Control Panel. 2. If you are viewing the Control Panel in Category View, click on Switch to Classic View. 3. Double-click the SoundMAX icon. The Microphone Setup allows you to optimize the microphone input settings for your particular configuration.
Operating Basics Region selection Telecommunication regulations vary from one region to another, so you will need to make sure the internal modem’s settings are correct for the region in which it will be used. The built-in modem can be used only in specified countries and regions. Using the modem in an area not specified for use may cause a system failure. Check the specified areas carefully before using it. To select a region, follow the steps below. 1.
Operating Basics Open dialog box, if the modem and Telephony Current Location region code do not match. A warning dialog box is displayed if current settings for region code and telephony location are incorrect. Modem Selection If the computer cannot recognize the internal modem, a dialog box is displayed. Select the COM port for your modem to use. Dialing Properties Select this item to display the dialing properties.
Operating Basics 2. Plug the other end of the modular cable into a telephone jack. Telephone jack Modular cable Modem jack Connecting the internal modem Do not pull on the cable or move the computer while the cable is connected. If you use a storage device such as an optical disc drive or hard disk drive connected to a 16-bit PC card, you might experience the following modem problems: ■ Modem speed is slow or communication is interrupted. ■ Skips may occur in sound.
Operating Basics Wireless communications The computer’s wireless communication function supports both Wireless LAN and Bluetooth devices. All models are provided with Wireless Communication switch. Some models are equipped with both Wireless LAN and Bluetooth functions. Wireless LAN The Wireless LAN is compatible with other LAN systems based on Direct Sequence Spread Spectrum /Orthogonal Frequency Division Multiplexing radio technology that complies with IEEE802.
Operating Basics Bluetooth wireless technology Some models in this series are equipped with Bluetooth™ wireless technology that eliminates the need for cables between electronic devices such as desktop computers, printers and mobile phones. You cannot use the built-in Bluetooth functions and an optional Bluetooth SD card 3 simultaneously. Bluetooth wireless technology has the following features: Worldwide operation The Bluetooth radio transmitter and receiver operate in the 2.
Operating Basics Release Notes related to the Bluetooth™ Stack for Windows® by TOSHIBA 1. Install: On Windows2000 or Windows XP, Bluetooth™ Stack for Windows® by TOSHIBA does not have a digital signature. 2. Fax application software: Regarding FAX application software, there are some software that you cannot use on this Bluetooth™ Stack. 3. Multi User: On Windows XP, the use of Bluetooth is not supported in a multi-user environment.
Operating Basics Wireless communication Indicator The wireless communication indicator indicates the status of the wireless communication functions. Indicator status Indication Indicator off Wireless communication switch is set to off. Automatic power down because of overheating. Power malfunction. Indicator glows Wireless communication switch is on. Wireless LAN or Bluetooth can be used by an application.
Operating Basics If you are using Fast Ethernet LAN (100 megabits per second, 100BASE-TX), be sure to connect with a CAT5 cable or higher. You cannot use a CAT3 cable. If you are using Ethernet LAN (10 megabits per second, 10BASE-T), you can connect with a CAT3 or higher. Connecting LAN cable To connect a LAN cable, follow the steps below. ■ Connect the AC adaptor before connecting a LAN cable. The AC adaptor must remain connected during LAN use.
Operating Basics Disconnecting LAN cable To disconnect a LAN cable, follow the steps below. Make sure the LAN Active indicator (orange LED) is out before you disconnect the computer from the LAN. 1. Pinch the lever on the connector in the computer’s LAN jack and pull out the connector. 2. Disconnect the cable from the LAN hub in the same manner. Check with your LAN administrator before disconnecting from the hub.
Operating Basics ■ Before carrying your computer, shut down the computer, disconnect the power cable and wait until the PC cools down. Failure to follow this instruction could result in minor injury. ■ Always turn off the power when you move the computer. If the power button has a lock, set it to the lock position. Also be careful not to subject the computer to impact. Failure to follow this instruction could result in damage to computer, computer failure or loss of data.
Operating Basics Taskbar Icon State Icon Description Normal HDD Protection is enabled. Protection HDD Protection is active. The hard disk drive head is in a safe position. OFF HDD Protection is disabled. TOSHIBA HDD Protection Properties You can make the HDD Protection settings by using the TOSHIBA HDD Protection Properties window. To open the window, click start, point to All Programs, point to TOSHIBA, point to Utilities and click HDD Protection setting.
Operating Basics Detection Level This function can be set to four levels. The sensitivity levels in which vibrations, impacts and similar occurrences are detected can be set to OFF, 1, 2 and 3 in ascending order. Level 3 is recommended for better protection of the computer. However, when the computer is used as handheld or in other unstable conditions, setting the detection level to 3 could result in frequent execution of HDD Protection, which will slow HDD reading and writing.
Operating Basics Heat dispersal To protect from overheating, the CPU has an internal temperature sensor. If the computer’s internal temperature rises to a certain level, the cooling fan is turned on or the processing speed is lowered. You can select whether to control the CPU temperature by turning on the fan first, then if necessary, lowering the CPU speed. Or, by lowering the CPU speed first, then if necessary, turning on the fan. Use the Cooling Method item of the Basic Setup tab in TOSHIBA Power Saver.
Chapter 5 The Keyboard The computer’s keyboard layouts are compatible with a 101/102-key enhanced keyboard. By pressing some keys in combination, all the 101/102-key keyboard functions can be executed on the computer. The number of keys on your keyboard depends on which country/region’s keyboard layout your computer is configured with. Keyboards for numerous languages are available. There are six types of keys: typewriter keys, function keys, soft keys, Hot keys, Windows special keys and keypad overlay.
The Keyboard Function keys: F1 … F12 The function keys (not to be confused with Fn) are the 12 keys at the top of your keyboard. These keys function differently from other keys. F1 through F12 are called function keys because they execute programmed functions when pressed. Used in combination with the Fn key, keys marked with icons execute specific functions on the computer. Refer to the section, Soft keys: Fn key combinations, in this chapter.
The Keyboard Press Fn + F10 or Fn + F11 to access the integrated keypad. When activated, the keys with gray markings on the bottom edge become numeric keypad keys (Fn + F11) or cursor control keys (Fn + F10). Refer to the Keypad overlay section in this chapter for more information on how to operate these keys. The power on default for both settings is off. Press Fn + F12 (ScrLock) to lock the cursor on a specific line. The power on default is off.
The Keyboard Instant security: Press Fn + F1 to blank the screen to prevent others from accessing your data. To restore the screen and original settings, press any key or press the Touch Pad. If a screensaver password is registered, a dialog box will appear. Enter the screensaver password and click OK. If no password is set, the screen will be restored when you press any key or press the Touch Pad. Power save mode: Pressing Fn + F2 changes the power save mode.
The Keyboard Internal LCD screen Brightness: Pressing Fn + F6 decreases the LCD screen brightness in decrements. When you press these hot keys, the current setting will be displayed for two seconds by an icon. You can also change this setting through the Screen brightness item of the Basic Setup tab in TOSHIBA Power Saver. Internal LCD screen Brightness: Pressing Fn + F7 increases the LCD screen brightness in increments.
The Keyboard LCD screen resolution selection: Press Fn + Space keys to change the display resolution. Each time when you press these hot keys, the LCD screen resolution changes as follows: The available resolution depends on the model. With WXGA+, you can change the resolution between 800 × 600 and 1024 × 768 pixels. TOSHIBA Zooming Utility (reduce): To reduce the icon size on the desktop or the application window, press the 1 key while holding down the Fn key.
The Keyboard Keypad overlay Your computer’s keyboard does not have an independent numeric keypad, but its numeric keypad overlay functions like one. The keys in the centre of the keyboard with gray letters make up the numeric keypad overlay. The overlay provides the same functions as the numeric keypad on the 101/102-key enhanced keyboard. Turning on the overlays The numeric keypad overlay can be used for numeric data input or cursor and page control. Arrow mode To turn on the Arrow mode, press Fn + F10.
The Keyboard Temporarily using normal keyboard (overlay on) While using the overlay, you can temporarily access the normal keyboard without turning off the overlay: 1. Hold Fn and press any other key. All keys will operate as if the overlay were off. 2. Type upper-case characters by holding Fn + Shift and pressing a character key. 3. Release Fn to continue using the overlay.
Chapter 6 Power and Power-Up Modes The computer’s power resources include the AC adaptor, battery pack and internal batteries. This chapter gives details on making the most effective use of these resources including charging and changing batteries, tips for saving battery power, and power up modes.
Power and Power-Up Modes Power conditions continued Power on AC adaptor Battery charge not is above low connected battery trigger point Power off (no operation) • Operates • LED: Battery off DC IN off Battery charge is below low battery trigger point • Operates • LED: Battery flashes orange DC IN off Battery charge is exhausted Computer goes into Hibernation Mode and shuts down No battery installed • Cannot operate • LED: Battery off DC IN off Power indicators As shown in the above table, the Batt
Power and Power-Up Modes DC IN indicator Check the DC IN indicator to determine the power status with the AC adaptor connected: Blue Indicates the AC adaptor is connected and supplying proper power to the computer. Flashing orange Indicates a problem with the power supply. Plug the AC adaptor into another power outlet. If it still does not operate properly, contact your dealer. No light Under any other conditions, the indicator does not light.
Power and Power-Up Modes Using a battery pack other than one supplied or specified by TOSHIBA (PA3356U) for this PC would interfere with the computer’s display when open and could damage the LCD display panel. Do not change the battery pack while the AC adaptor is connected. Before you remove the battery pack, save your data and shut down the computer, or set the computer to Hibernation Mode. While entering Hibernation Mode, the computer saves the contents of memory to the hard disk drive.
Power and Power-Up Modes Real Time Clock (RTC) battery The Real Time Clock (RTC) battery provides power for the internal real time clock and calendar. It also maintains the system configuration. If the RTC battery becomes completely discharged, the system loses this data and the real time clock and calendar stop working. The following message appears when you turn on the power: S **** RTC battery is low or CMOS checksum is inconsistent **** Press [F1] key to set Date/Time.
Power and Power-Up Modes 3. Never short circuit the battery pack by either accidentally or intentionally bringing the battery terminals in contact with another conductive object. This could cause serious injury or a fire, and could also damage the battery pack. Always wrap the battery pack in plastic (or place it in a plastic bag) whenever transporting it, to avoid exposing the terminals to another conductive object which could result in serious injury.
Power and Power-Up Modes 13. Always immediately turn the power off and disconnect the power cable plug from the plug socket if you observe any of the following conditions: ■ Offensive or unusual odor ■ Excessive heat ■ Discoloration ■ Deformation ■ Smoke ■ Other unusual event during use, such as abnormal sound In such an event, immediately remove the battery pack from the PC.
Power and Power-Up Modes Note 1. Never remove the battery pack while the Wake-up on LAN function is enabled. Data will be lost. Before you remove a battery pack, disable the Wake-up on LAN function. 2. To ensure the battery pack maintains maximum capacity, operate the computer on battery power once a week until the battery pack is fully discharged. Refer to the section Extending battery life in this chapter for procedures.
Power and Power-Up Modes Time The following table shows the approximate time required to fully charge a discharged battery. Charging time (hours) Battery type Power on Power off Battery pack (4700mAh) about 5.5 to 12.0 about 3.0 RTC battery 8.0 Doesn’t charge The charging time when the computer is on is affected by ambient temperature, the temperature of the computer and how you use the computer.
Power and Power-Up Modes Monitoring battery capacity Remaining battery power can be monitored in TOSHIBA Power Saver. ■ Wait at least 16 seconds after turning on the computer before trying to monitor the remaining operating time. The computer needs this time to check the battery’s remaining capacity and to calculate the remaining operating time, based on the current power consumption rate and remaining battery capacity. The actual remaining operating time may differ slightly from the calculated time.
Power and Power-Up Modes Retaining data with power off When you turn off your computer with fully charged batteries, the batteries retain data for the following approximate time periods: Retention time Battery type State and Retention Time Battery pack (4700mAh) about 6 days (Standby Mode) about 60 days (Boot mode) RTC battery 30 days Extending battery life To maximize the life of your battery pack: ■ At least once a month, disconnect the computer from a power source and operate it on battery power u
Power and Power-Up Modes Replacing the battery pack Using a battery pack other than one supplied or specified by TOSHIBA (PA3356U) for this PC would interfere with the computer’s display when open and could damage the LCD display panel. The battery pack is classified as a consumable item. The operating life of the battery pack will gradually reduce through repeated charging and discharging. It will need to be replaced when it reaches the end of its operating life.
Power and Power-Up Modes To install a battery pack, follow the steps below. Do not touch the battery release latch while holding the computer. Or you may get injured by the dropped battery pack by unintentional release of the battery release latch. Always use the Battery pack that was provided with your computer, or a compatible Battery pack. 1. Insert the battery pack all the way to the end (1). 2.
Power and Power-Up Modes User Password field ■ Set (button) Click this button to register a password of up to 50 characters. After a password is set, you will be prompted to enter it when you start the computer. ■ After you set the password, a dialog box will be displayed asking whether you want to save it to a floppy disk or other media. If you forget the password, you can open the password file on another computer. Be sure to keep the media in a safe place.
Power and Power-Up Modes ■ Disable (button) Click this button to invalidate the token. You cannot re-validate old tokens, but you can use the same SD cards to create new tokens. After using the token created for authentication, do not leave it inserted in the SD card slot, ensure that the token is removed from the slot and stored in a safe location.
Power and Power-Up Modes If you enter the password incorrectly three times in a row, the computer shuts off. In this case, you must turn the computer back on to retry password entry. Power-up modes The computer has the following power-up modes: ■ Boot: Computer shuts down without saving data. Always save your work before you turn the computer off in boot mode. ■ Hibernation: Data in memory is saved to the hard disk drive. ■ Standby: Data is maintained in the computer’s memory.
Chapter 7 HW Setup This chapter explains how to use TOSHIBA HW Setup program to configure your computer, and provides information on setting up the Execute-Disable Bit Capability and TPM (optional). Accessing HW Setup To run HW Setup, click start, click Control Panel, click Printers and Other Hardware and select TOSHIBA HWSetup. HW Setup window The HW Setup window contains the following tabs: General, Display, Boot Priority, Keyboard, CPU, LAN, Device Config and USB.
HW Setup General This window displays the BIOS version and contains two buttons: Default and About. Default Returns all HW Setup values to the factory settings. About Displays the HW Setup version. Setup This field displays BIOS Version and date. Display This tab lets you customize your computer’s display settings for either the internal LCD screen or for an external monitor. Power On Display Lets you select the display to be used when the computer is booted.
HW Setup Boot Priority Boot Priority Options This option sets the priority for booting the computer. Select from the following settings: HDD −> FDD −> CD-ROM −> LAN The computer looks for bootable files in the following order: HDD, floppy disk drive*1, CD-ROM*2 and LAN (Default). FDD −> HDD −> CD-ROM −> LAN The computer looks for bootable files in the following order: floppy disk drive*1, HDD, CD-ROM*2 and LAN.
HW Setup To change the boot drive, follow the steps below. 1. Hold down F12 and boot the computer. 2. The following menu will be displayed with the following icons: Built-in HDD, CD-ROM, FDD (or SD memory card), Network (LAN), USB Memory boot. A bar will appear only under the selected device. 3. Use the left/right cursor keys to highlight the boot device you want and press Enter.
HW Setup HDD Priority Options Set the priority of the HDD as a startup device. Built-in HDD -> USB (Default) The priority is set as built-in HDD -> USB. USB -> Built-in HDD The priority is set as USB memory -> built-in HDD. USB Memory BIOS Support Type Set the type of the USB memory as a startup device. HDD Set the type of the USB memory to be equivalent to the HDD (Default). * Based on the HDD order in the Boot Priority Options item.
HW Setup CPU This function lets you set the CPU operating mode. This option is displayed only on models with an Intel® Core™ Duo processor and Intel® Core™ Solo processor. Dynamic CPU Frequency Mode This option lets you choose from the following settings: Dynamically Switchable CPU power consumption and clock speed automatic switching function is enabled. When the computer is in use, CPU operation is automatically switched when necessary (Default).
HW Setup Device Config Device Configuration This option lets you set the device configuration. All Devices BIOS sets all devices. Setup by OS Operating system sets devices that it can control (Default). USB USB KB/Mouse Legacy Emulation Use this option to enable or disable USB keyboard/mouse legacy emulation. If your operating system does not support USB, you can still use a USB mouse and keyboard by setting the USB KB/Mouse Legacy Emulation item to Enabled.
HW Setup Configuring the Execute-Disable Bit Capability and TPM (optional) The configurations for the Execute-Disable Bit Capability and TPM are carried out in the BIOS setup program. These functions are provided with some models. Notes before using the BIOS Setup ■ In most cases, changes to the system’s configuration should be made within Windows by using applications such as TOSHIBA HW Setup, TOSHIBA Password Utility, TOSHIBA Power Saver, Windows Device Manager and so forth.
HW Setup Ending the BIOS Setup Program Save the changes and end the program. 1. Press the End Key. The “Are you sure? (Y/N) The changes you made will cause the system to reboot.” message is displayed. 2. Press the Y key. The configured settings are saved and the BIOS setup program ends. The computer may reboot depending on the settings that were modified. Ending the BIOS Setup Program Halfway The configuration settings can be terminated halfway without saving any of the changes made. 1. Press the Esc key.
HW Setup Enhanced C-States This feature enables or disables the Enhanced C-States. This option is displayed only on models with an Intel® Core™ Duo processor and Intel® Core™ Solo processor. Enabled This lowers the power consumption (Default). Disabled This does not lower the power consumption. Execute-Disable Bit Capability This setting, which is displayed on the first page of the setup screen, configures the Execute-Disable Bit function of the CPU.
HW Setup Clear TPM Owner This setting is used to erase the data in TPM when disposing of the computer or when the owner of the computer changes, etc. Once this operation is carried out, the TPM configuration settings are erased, such that the encrypted data can no longer be decrypted and the files can no longer be read. Please backup or delete the data as necessary before carrying out this operation. The operating procedure is as follows: 1.
HW Setup 7-12 User’s Manual
Chapter 8 Optional Devices Optional devices can expand the computer’s capabilities and its versatility.
Optional Devices PC card The computer is equipped with a PC card slot that can accommodate a Type II card. Any PC card that meets industry standards (manufactured by TOSHIBA or other vendor) can be installed. The slot supports 16-bit PC cards, including PC card 16’s multifunction card and CardBus PC cards. CardBus supports the new standard of 32-bit PC cards. The bus provides superior performance for the greater demands of multimedia data transmission. PC cards can sometimes become hot during PC operation.
Optional Devices Removing a PC card To remove the PC card, follow the steps below. 1. Open the Safely Remove Hardware icon on the Task Bar. 2. Point to PC card and click. 3. Press the PC card eject button to extend it. If the PC card is not inserted all the way, the eject button may not cause it to pop out sufficiently to allows it to be grasped. Be sure to push the PC card firmly into the computer and slide the eject button again. 4. Press the extended eject button to pop the card out slightly. 5.
Optional Devices Media care Observe the following precautions when handling the card. Card care ■ Do not twist or bend cards. ■ Do not expose cards to liquids or store in humid areas or lay media close to containers of liquid. ■ Do not touch the metal part of a card or expose it to liquids or let it get dirty. ■ After using card, return it to its case. ■ The card is designed so that it can be inserted only one way. Do not try to force the card into the slot.
Optional Devices Inserting an SD card To insert an SD card, follow the steps below. 1. Insert an SD card in the Bridge media slot. 2. Press gently to ensure a firm connection. Bridge media slot SD card Inserting an SD card ■ Make sure the SD card is oriented properly before you insert it. ■ Do not turn the computer off or switch to Standby Mode or Hibernate Mode while files are being copied - doing so may cause data to be lost. Removing an SD card To remove an SD card, follow the steps below. 1.
Optional Devices ■ Make sure the Bridge media slot indicator is out before you remove the SD card or turn off the computer’s power. If you remove the SD card or turn off the power while the computer is accessing the SD card you may lose data or damage the card. ■ Do not remove an SD card while the computer is in Standby or Hibernation mode. The computer could become unstable or data in the SD card could be lost.
Optional Devices ■ The slot does not support Magic Gate functions. ■ Memory Stick Duo/PRO Duo and the Memory Stick adaptor are not compatible with the Bridge media slot. Do not insert Memory Stick Duo/ PRO Duo into the slot. Data may be lost or damaged if you use any card other than those supported. Write protection Memory Stick can be write protected to safeguard your data. To write-protect a Memory Stick, slide the lock on the back of the Memory Stick to the lock position.
Optional Devices xD picture card The computer is equipped with a Bridge media slot that can accommodate xD picture cards with various memory capacities. The xD picture card let you easily transfer data from devices, such as digital cameras that use xD picture card flash-memory. Keep foreign objects out of the Bridge media slot. Never allow metal objects, such as screws, staples and paper clips, to enter the PC or keyboard.
Optional Devices MultiMediaCard The computer is equipped with the Bridge media slot that can accommodate MultiMediaCard flash memory technology with various memory capacities. MultiMediaCards let you easily transfer data from devices, such as digital cameras and Personal Digital Assistants, that use MultiMediaCard flash-memory. The cards have a high level of security and copy protection features. Keep foreign objects out of the Bridge media slot.
Optional Devices Removing a MultiMediaCard To remove a MultiMediaCard, follow the steps below. 1. Open the Safely Remove Hardware icon on the Task Bar. 2. Point to MultiMediaCard and click. 3. Push in the card and release it to pop the card out slightly. 4. Grasp the card and remove it. Bridge media slot MultiMediaCard Removing a MultiMediaCard ■ Make sure the Bridge media slot indicator is out before you remove the MultiMediaCard or turn off the computer’s power.
Optional Devices ■ Use only memory modules approved by TOSHIBA. ■ Do not try to install or remove a memory module under the following conditions as you can damage the computer and/or the module, and you risk losing data: a. The computer is turned on. b. The computer was shut down using either Standby Mode or Hibernation Mode. c. Wake-up on LAN is enabled. ■ Be careful not to let screws or other foreign matter fall into the computer. It could cause malfunction or electric shock.
Optional Devices 6. Slip your finger under a notch at the end of the keyboard brace and lift up to release latches and remove the keyboard brace. Keyboard brace Removing the keyboard brace 7. Remove two screws securing the keyboard. Use a point size 1 Phillips screwdriver. 8. Lift up the back of the keyboard, rotate it toward you and lay in face down on the palm rest. ■ When you move the keyboard forward, do not touch the keys. Doing so could cause misalignment.
Optional Devices 9. Remove the two screws and take off the memory module cover. Screws Memory module cover Removing the memory module cover ■ Do not touch the connectors on the memory module or on the computer. Debris on the connectors may cause memory access problems. ■ The memory module cover will be hot after using the computer for long periods of time. Use care when removing. The slot A is reserved for main memory. Use the slot B for expanded memory. If only one card is installed, use the slot A.
Optional Devices 11. Replace the memory module cover and screw in the two screws. Screws Memory module cover Replace the memory module cover 12. Insert the tabs on the front of the keyboard into the corresponding notches on the computer and place the keyboard down. When seating the keyboard, be sure to connect the circuit board if the keyboard ribbon cable was pulled out while you were removing the keyboard. 13. Screw the two screws and secure the keyboard.
Optional Devices 6. Grasp the module by the sides and pull it out. ■ If you use the computer for a long time, the memory modules and the circuits located close to the memory modules will become hot. In this case, let them cool to room temperature before you replace them. ■ Do not touch the connectors on the memory module or on the computer. Debris on the connectors may cause memory access problems. Latches Removing the memory module 7.
Optional Devices Battery Charger The battery charger provides a convenient way to charge battery packs without requiring the use of your computer. The battery charger holds up to two battery packs (lithium ion). USB floppy disk drive (USB FDD Kit) The USB floppy disk drive module can be connected to the USB port. For details on connecting the USB floppy disk drive module, refer to Chapter 4, Operating Basics.
Optional Devices i.LINK (IEEE1394) i.LINK (IEEE1394) is used for high-speed data transfer for a range of compatible devices such as ■ Digital video cameras ■ Hard disk drives ■ MO drives ■ Writable optical disc drives i.LINK uses a four-pin connector, which does not carry any electric current. External devices will need their own power supply to operate. Precautions ■ Make a back-up of your data before transferring it to the computer. There is a possibility that the original data will be damaged.
Optional Devices Connecting 1. Make sure the connectors are properly aligned and plug the i.LINK (IEEE1394) cable into the computer. i.LINK (IEEE1394) port i.LINK (IEEE1394) connector Connecting the i.LINK (IEEE1394) cable into the computer 2. Plug the other end of the cable into the device. Note the following when you use i.LINK: ■ You may need to install drivers for your i.LINK devices. ■ Not all i.LINK devices have been tested. Therefore, compatibility with all i.LINK devices cannot be guaranteed.
Optional Devices Wireless Optical Mouse with Bluetooth Technology The Wireless optical mouse with Bluetooth Technology is a wireless optical mouse compatible with Bluetooth. You can buy the Wireless optical mouse with Bluetooth Technology from TOSHIBA dealer. Wireless Stereo Headset with Bluetooth Technology The Wireless Stereo Headset with Bluetooth Technology is a wireless stereo headphone compatible with Bluetooth. You can buy the Wireless Stereo Headset with Bluetooth Technology from TOSHIBA dealer.
Optional Devices 8-20 User’s Manual
Chapter 9 Troubleshooting TOSHIBA designed the computer for durability. However, should problems occur, following the procedures in this chapter can help to determine the cause. All readers should become familiar with this chapter. Knowing what might go wrong can help prevent problems from occurring. Problem solving process Resolving problems will be much easier if you observe the following guidelines: ■ Stop immediately when you recognize a problem exists. Further action may result in data loss or damage.
Troubleshooting Preliminary checklist Consider the simplest solution first. The items in this checklist are easy to fix and yet can cause what appears to be a serious problem. ■ Make sure you turn on all peripheral devices before you turn on the computer. This includes your printer and any other external device you are using. ■ Before you attach an external device, turn the computer off. When you turn the computer back on it recognizes the new device.
Troubleshooting Software Hardware The problems may be caused by your software or disk. If you cannot load a software package, the media may be damaged or the program might be corrupted. Try loading another copy of the software. If an error message appears while you are using a software package, check the software documentation. These documents usually include a problem solving section or a summary of error messages. Next, check any error messages in the operating system documentation.
Troubleshooting Self test When the computer starts up, the self test will be run automatically, and the following will be displayed: S In Touch with Tomorrow TOSHIBA This message remains on the screen for a few seconds. If the self test is successful, the computer tries to load the operating system, depending on how the Boot Priority is set in the TOSHIBA HW Setup program.
Troubleshooting AC power If you have trouble turning on the computer with the AC adaptor connected, check the DC IN indicator. Refer to Chapter 6, Power and Power-Up Modes for more information. Problem Procedure AC adaptor doesn’t power the computer (DC IN indicator does not glow blue) Check the connections. Make sure the cord is firmly connected to the computer and a power outlet. Check the condition of the cord and terminals. If the cord is frayed or damaged, replace it.
Troubleshooting Problem Procedure Battery doesn’t charge when the AC adaptor is attached (Battery indicator does not glow orange.) If the battery is completely discharged, it will not begin charging immediately. Wait a few minutes. If the battery still does not charge, make sure the outlet of the AC adaptor is supplying power. Test it by plugging in an appliance. Check whether the battery is hot or cold to the touch. If the battery is too hot or too cold, it will not charge properly.
Troubleshooting Real Time Clock Problem Procedure The following message is Displayed on the LCD screen: RTC battery is low or CMOS checksum is inconsistent. Press [F1] key to set Date/Time. The charge in the RTC battery has run out - you will need to set the date and time in the BIOS setup using the following steps: 1. Press F1 key. BIOS setup will boot up. 2. Set the date in System Date. 3. Set the time in System Time. 4. Press End key. Confirmation message will appear. 5. Press Y key.
Troubleshooting Internal LCD display panel Apparent LCD problems may be related to the computer’s setup. Refer to Chapter 7, HW Setup, for more information. Problem Procedure No display Press hotkeys Fn + F5 to change the display priority, to make sure it is not set for an external monitor. Markings appear on the The marks may have come from contact with the LCD screen. keyboard or Touch Pad. Try wiping the LCD screen gently with a clean dry cloth.
Troubleshooting DVD-ROM&CD-R/RW drive For more information, refer to Chapter 4, Operating Basics. Problem Procedure You cannot access a CD/DVD in the drive Make sure the drive’s disc tray is securely closed. Press gently until it clicks into place. Open the disc tray and make sure the CD/DVD is properly seated. It should lie flat with the label facing up. A foreign object in the disc tray could block laser light from reading the CD/DVD. Make sure there is no obstruction. Remove any foreign object.
Troubleshooting Problem Procedure Cannot write correctly If you have trouble writing, make sure you are observing the following precautions: ■ Use only media recommended by TOSHIBA. ■ Do not use the mouse or keyboard during writing. ■ Use only the software supplied with the computer for recording. ■ Do not run or start other software during writing. ■ Do not jar the computer during writing. ■ Do not connect/disconnect external devices or install/remove internal cards during writing.
Troubleshooting Problem Procedure Some CD/DVDs run The software or hardware configuration may be correctly, but others do causing a problem. Make sure the hardware not configuration matches your software’s needs. Check the CD/DVD’s documentation. Check the type of CD/DVD you are using.
Troubleshooting SD card Refer also to Chapter 8, Optional Devices. Problem Procedure SD card error occurs Reseat the SD card to make sure it is firmly connected. Check the card’s documentation. You cannot write to an SD memory card Make sure the card is not write protected. You cannot read a file Make sure the target file is on the SD memory card inserted in the slot. If problems persist, contact your dealer. PC card Refer also to Chapter 8, Optional Devices.
Troubleshooting xD picture card Refer also to Chapter 8, Optional Devices. Problem Procedure xD picture card error occurs Reseat the xD picture card to make sure it is firmly connected. Check the card’s documentation. You cannot read a file Make sure the target file is on the xD picture card inserted in the slot. If problems persist, contact your dealer. MultiMediaCard Refer also to Chapter 8, Optional Devices.
Troubleshooting Problem Procedure Double-tapping does not work Try changing the double-click speed setting in the mouse control utility. 1. Click start, click Control Panel, click Printers and Other Hardware and select Mouse icon. 2. Click the Buttons tab. 3. Set the double-click speed as required and click OK. If problems persist, contact your dealer. The reaction of Touch pad is either too sensitive or not sensitive enough. Adjust the touch Sensitivity. 1. Click start and open the Control Panel. 2.
Troubleshooting Problem Procedure The mouse pointer moves too fast or too slow Try changing the speed setting in the mouse control utility. 1. Click start, click Control Panel, click Printers and Other Hardware and select Mouse icon. 2. Click the Pointer Options tab. 3. Set the speed as required and click OK. The mouse pointer moves erratically The mouse might be dirty. Refer to your mouse documentation for instructions on cleaning. If problems persist, contact your dealer.
Troubleshooting USB device Refer also to your USB device’s documentation. Problem Procedure USB device does not work Check for a firm cable connection between the USB ports on the computer and the USB device. Make sure the USB device drivers are properly installed. Refer to your Windows XP documentation for information on checking the drivers. If you are using an operating system that does not support USB, you can still use a USB mouse and/or USB keyboard.
Troubleshooting Sound system Refer also to documentation for your audio devices. Problem Procedure No sound is heard Adjust the volume control dial. Check the software volume settings. Make sure the headphone connection is secure. If problems persist, contact your dealer. Check Windows Device Manager.
Troubleshooting i.LINK (IEEE1394) device Problem Procedure i.LINK device does not function Make sure the cable is securely connected to the computer and to the device. Make sure the device’s power is turned on. Reinstall the drivers. Open the Windows Control Panel and double-click the Add Hardware icon. Follow the on-screen directions. Restart Windows. If problems persist, contact your dealer.
Troubleshooting Problem Procedure You cannot receive an incoming call Check the rings before auto answer setting in your communications application. If problems persist, contact your dealer. Problem Procedure Cannot access LAN Check for a firm cable connection between the LAN jack and the LAN hub. Wake-up on LAN does not work Make sure the AC adaptor is connected. The Wake-up on LAN function consumes power even when the system is off. If problems persist, consult your LAN administrator.
Troubleshooting Disposing of PC and PC batteries ■ Discard this PC in accordance with ordinances or rules of local regulations. For further information, contact your local government. ■ This PC contains rechargeable batteries. After repeated use, the batteries will finally lose their ability to hold a charge and you will need to replace them. Under certain applicable laws and regulation, it may be illegal to dispose of old batteries by placing them in the trash. ■ Please be kind to our shared environment.
Troubleshooting TOSHIBA support If you require any additional help using your computer or if you are having problems operating the computer, you may need to contact TOSHIBA for additional technical assistance. Before you call Some problems you experience may be related to software or the operating system, it is important to investigate other sources of assistance first. Before contacting TOSHIBA, try the following: ■ Review troubleshooting sections in the documentation for software and peripheral devices.
Troubleshooting 9-22 User’s Manual
Chapter 10 Legal Footnotes This chapter states the Disclaimers information. CPU*1 Central Processing Unit (“CPU”) Performance Legal Footnotes.
Legal Footnotes Under some conditions, your computer product may automatically shut-down. This is a normal protective feature designed to reduce the risk of lost data or damage to the product when used outside recommended conditions. To avoid risk of lost data, always make back-up copies of data by periodically storing it on an external storage medium. For optimum performance, use your computer product only under recommended conditions. Read additional restrictions in your product documentation.
Legal Footnotes LCD*5 Over a period of time, and depending on the usage of the computer, the brightness of the LCD screen will deteriorate. This is an intrinsic characteristic of LCD technology. Maximum brightness is only available when operating in AC power mode. The screen will dim when the computer is operated on battery power and you may not be able to increase the brightness of the screen.
Legal Footnotes 10-4 User’s Manual
Appendix A Specifications This appendix summarizes the computer’s technical specifications. Physical Dimensions Weight (typical) 1.86 kilograms, configured with: 12.1" WXGA, 512MB RAM, 40GB HDD, DVD-ROM&CD-R/RW, Wireless LAN. Weight will vary with other configurations. Above weights are measured at specific criteria. They are not guaranteed as the maximum weight of the actual product. Size 299 (w) × 225 (d) × 34.0/34.
Specifications Power Requirements AC adaptor 100-240 volts AC 50 or 60 hertz (cycles per second) Computer 15 VDC 4.
Specifications User’s Manual Transmitting level -10 dBm Receiving level -10 to -40 dBm Input/output impedance 600 ohms ±30% Error correcting MNP class 4 and ITU-T V.42 Data compression MNP class 5 and ITU-T V.42bis Power supply +3.
Specifications A-4 User’s Manual
Appendix B Display Controller and Modes Display controller The display controller interprets software commands into hardware commands that turn particular parts on the screen on or off. As indicated below, there are two types of video modes. ■ Intel® 945GM model supports up to 2048 horizontal × 1536 vertical pixels. ■ Intel® 940GML model supports up to 1920 horizontal × 1440 vertical pixels. Refer to the table on the next page which describes in detail supported video modes.
Display Controller and Modes Table1 Video modes (VGA) Video mode Type Resolution Character matrix (pels) Colors Scanning frequency Vertical (Hz) 0, 1 VGA Text 40 × 25 Characters 8×8 16 of 256K 70 2, 3 VGA Text 80 × 25 Characters 8×8 16 of 256K 70 0*, 1* VGA Text 40 × 25 Characters 8 × 14 16 of 256K 70 2*, 3* VGA Text 80 × 25 Characters 8 × 14 16 of 256K 70 0+, 1+ VGA Text 40 × 25 Characters 9 × 16 16 of 256K 70 2+, 3+ VGA Text 80 × 25 Characters 9 × 16 16 of 256K 70
Display Controller and Modes Table1 Video modes (VGA) continued Video mode Type Resolution Character matrix (pels) Colors Scanning frequency Vertical (Hz) D VGA Grph 320 × 200 Pels 8×8 16 of 256K 70 E VGA Grph 640 × 200 Pels 8×8 16 of 256K 70 F VGA Grph 640 × 350 Pels 8 × 14 Mono 70 10 VGA Grph 640 × 350 Pels 8 × 14 16 of 256K 70 11 VGA Grph 640 × 480 Pels 8 × 16 2 of 256K 60 12 VGA Grph 640 × 480 Pels 8 × 16 16 of 256K 60 13 VGA Grph 320 × 200 Pels 8×8 256 of
Display Controller and Modes Table 2 Video modes (Intel® 945GM model) ■ Vertical Frequency can be set up when outputting to External Monitor. ■ The screen may not be displayed properly in high resolution mode while running 3D applications, during DVD playback, etc. Reduce the resolution until the screen is displayed properly in such cases.
Display Controller and Modes Table 2 Video modes (Intel® 945GM model) continued ■ Vertical Frequency can be set up when outputting to External Monitor. ■ The screen may not be displayed properly in high resolution mode while running 3D applications, during DVD playback, etc. Reduce the resolution until the screen is displayed properly in such cases.
Display Controller and Modes Table 2 Video modes (Intel® 945GM model) continued ■ Vertical Frequency can be set up when outputting to External Monitor. ■ The screen may not be displayed properly in high resolution mode while running 3D applications, during DVD playback, etc. Reduce the resolution until the screen is displayed properly in such cases.
Display Controller and Modes Table 3 Video modes (Intel® 940GML model) ■ Vertical Frequency can be set up when outputting to External Monitor. ■ The screen may not be displayed properly in high resolution mode while running 3D applications, during DVD playback, etc. Reduce the resolution until the screen is displayed properly in such cases.
Display Controller and Modes Table 3 Video modes (Intel® 940GML model) continued ■ Vertical Frequency can be set up when outputting to External Monitor. ■ The screen may not be displayed properly in high resolution mode while running 3D applications, during DVD playback, etc. Reduce the resolution until the screen is displayed properly in such cases.
Display Controller and Modes Table 3 Video modes (Intel® 940GML model) continued ■ Vertical Frequency can be set up when outputting to External Monitor. ■ The screen may not be displayed properly in high resolution mode while running 3D applications, during DVD playback, etc. Reduce the resolution until the screen is displayed properly in such cases.
Display Controller and Modes B-10 User’s Manual
Appendix C Wireless LAN Card Specifications Form Factor PCI-Ex MiniCard Type Compatibility ■ IEEE 802.11 Standard for Wireless LANS ■ Wi-Fi (Wireless Fidelity) certified by the Wi-Fi Alliance. The ‘Wi-Fi CERTIFIED’ logo is a certification mark of the Wi-Fi Alliance. Network Operating System ■ Microsoft Windows® Networking Media Access Protocol ■ CSMA/CA (Collision Avoidance) with Acknowledgment (ACK) Data Rate ■ Theoretical maximum speed: 54Mbps (IEEE802.11a/IEEE802.
Wireless LAN Refer to the sheet “Information to the User” for regulatory information that may apply in your country/region. R-F Frequency ■ Band 5GHz (5150-5850 MHz) (Revision A) ■ Band 2.4GHz (2400-2483.5 MHz) (Revision B, G) Modulation Technique ■ DSSS-CCK, DSSS-DQPSK, DSSS-DBPSK (Revision B) ■ OFDM-BPSK, OFDM-QPSK, OFDM-16QAM, OFDM-64QAM (Revision A, G) The range of the wireless signal is related to the transmit rate of the wireless communication.
Wireless LAN 9 2452 10 2457*1 11 2462 12 2467*2 13 2472*2 *1 Factory-set default channels *2 Refer to the sheet Approved Countries/Regions for use for the countries/regions that in which these channels can be used. When installing Wireless LAN cards, the channel configuration is managed as follows: ■ For wireless clients that operate in a Wireless LAN Infrastructure, the Wireless LAN card will automatically start operation at the channel identified by the Wireless LAN Access Point.
Wireless LAN C-4 100 5500 104 5520 108 5540 112 5560 116 5580 120 5600 124 5620 128 5640 132 5660 136 5680 140 5700 149 5745 153 5765 157 5785 161 5805 165 5825 User’s Manual
Appendix D AC Power Cord and Connectors The power cord’s AC input plug must be compatible with the various international AC power outlets and the cord must meet the standards for the country/region in which it is used. All cords must meet the following specifications: Length: Minimum 2 meters Wire size: Minimum 0.75 mm2 Current rating: Minimum 2.5 amperes Voltage rating: 125 or 250 VAC (depending on country/region’s power standards) Certification agencies U.S.
AC Power Cord and Connectors In Europe, two conductors power cord must be VDE type, H05VVH2-F or H03VVH2-F and for three conductors power cord must be VDE type, H05VV-F. For the United States and Canada, two pin plug configuration must be a 2-15P (250V) or 1-15P (125V) and three pin plug configuration must be 6-15P (250V) or 5-15P (125V) as designated in the U.S. National Electrical code handbook and the Canadian Electrical Code Part II. The following illustrations show the plug shapes for the U.S.A.
Appendix E If your computer is stolen Always take care of your computer and try to prevent it from being stolen. You are the owner of a valuable technical device, which may be highly attractive to thieves, so please do not leave it unattended in a public place. To further help protect against theft, security cables can be bought for use with your notebook when it is being used at home or in the office. Make a note of your computer’s machine type, model number, and serial number, and put it in a safe place.
If your computer is stolen TOSHIBA Theft Registration Send to: Fax number: TOSHIBA Europe GmbH Technical Service and Support Leibnizstr. 2 93055 Regensburg Germany +49 (0) 941 7807 921 Country stolen: Machine type: (e.g. TOSHIBA Pocket PC e350) Model number: (e.g. PSA50 YXT) Serial number: (e.g.
Glossary The terms in this glossary cover topics related to this manual. Alternate naming is included for reference.
Glossary LCD: liquid crystal display LED: light emitting diode LSI: large scale integration MB: megabyte MS-DOS: Microsoft Disk Operating System OCR: optical character recognition (reader) PCB: printed circuit board PCI: peripheral component interconnect RAM: random access memory RGB: red, green, and blue ROM: read only memory RTC: real time clock SCSI: small computer system interface SIO: serial input/output SXGA+: super extended graphics array plus TFT: thin-film transistor UART: universal asynchronous r
Glossary analog signal: A signal whose characteristics such as amplitude and frequency vary in proportion to (are an analog of) the value to be transmitted. Voice communications are analog signals. ANSI: American National Standards Institute. An organization established to adopt and define standards for a variety of technical disciplines. For example, ANSI defined the ASCII standard and other information processing requirements. antistatic: A material used to prevent the buildup of static electricity.
Glossary bus: An interface for transmission of signals, data or electric power. byte: The representation of a single character. A sequence of eight bits treated as a single unit; also the smallest addressable unit within the system. C cache memory: High speed memory which stores data that increases processor speed and data transfer rate. When the CPU reads data from main memory, it stores a copy of this data in cache memory.
Glossary compatibility: 1) The ability of one computer to accept and process data in the same manner as another computer without modifying the data or the media upon which it is being transferred. 2) the ability of one device to connect to or communicate with another system or component. components: Elements or parts (of a system) which make up the whole (system). computer program: A set of instructions written for a computer that enable it to achieve a desired result.
Glossary delete: To remove data from a disk or other data storage device. Synonymous with erase. device driver: A program that controls communication between a specific peripheral device and the computer. The CONFIG.SYS file contains device drivers that MS-DOS loads when you turn the computer on. dialog box: A window that accepts user input to make system settings or record other information. disk drive: The device that randomly accesses information on a disk and copies it to the computer’s memory.
Glossary erase: See delete. escape: 1) A code (ASCII code 27), signaling the computer that what follows are commands; used with peripheral devices such as printers and modems. 2) A means of aborting the task currently in progress. escape guard time: A time before and after an escape code is sent to the modem which distinguishes between escapes that are part of the transmitted data, and escapes that are intended as a command to the modem. execute: To interpret and execute an instruction.
Glossary H hard disk: A non-removable disk usually referred to as drive C. The factory installs this disk and only a trained engineer can remove it for servicing. Also called fixed disk. hard disk drive (HDD): An electromechanical device that reads and writes a hard disk. See also hard disk. hardware: The physical electronic and mechanical components of a computer system: typically, the computer itself, external disk drives, etc. See also software and firmware.
Glossary I/O devices: Equipment used to communicate with the computer and transfer data to and from it. IrDA 1.1: An industry standard that enables cableless infrared serial data transfer at speeds of up to 4 Mbps. J jumper: A small clip or wire that allows you to change the hardware characteristics by electrically connecting two points of a circuit. K K: Taken from the Greek word kilo, meaning 1000; often used as equivalent to 1024, or 2 raised to the 10th power. See also byte and kilobyte.
Glossary microprocessor: A hardware component contained in a single integrated circuit that carries out instructions. Also called the central processing unit (CPU), one of the main parts of the computer. mode: A method of operation, for example, the boot mode, Standby Mode or the Hibernation Mode. modem: Derived from modulator/demodulator, a device that converts (modulates) digital data for transmission over telephone lines and then converts modulated data (demodulates) to digital format where received.
Glossary P parallel interface: Refers to a type of information exchange that transmits information one byte (8 bits) at a time. See also serial interface. parity: 1) The symmetrical relationship between two parameter values (integers) both of which are either on or off; odd or even; 0 or 1. 2) In serial communications, an error detection bit that is added to a group of data bits making the sum of the bits even or odd. Parity can be set to none, odd, or even.
Glossary Random Access Memory (RAM): High speed memory within the computer circuitry that can be read or written to. restart: Resetting a computer without turning it off (also called “warm boot” or “soft reset”). See also boot. RGB: Red, green, and blue. A device that uses three input signals, each activating an electron gun for a primary additive color (red, green, and blue) or port for using such a device. See also CRT. RJ11: A modular telephone jack. RJ45: A modular LAN jack.
Glossary T terminal: A typewriter-like keyboard and CRT display screen connected to the computer for data input/output. TFT display: A liquid crystal display (LCD) made from an array of liquid crystal cells using active-matrix technology with thin film transistor (TFT) to drive each cell. Touch Pad: A pointing device integrated into the TOSHIBA computer palm rest. TTL: Transistor-transistor logic. A logic circuit design that uses switching transistors for gates and storage.
Glossary Glossary-14 User’s Manual
Index A AC adaptor, 1-5 additional, 1-18, 8-15 connecting, 3-6 Arrow mode indicator location, 2-10 ASCII characters, 5-8 B Battery charger, 1-18, 8-16 charging, 6-8 extending life, 6-11 indicator, 2-9, 6-2 lock location, 2-6 monitoring capacity, 6-10 pack location, 2-6 real time clock, 1-5, 6-5 release latch location, 2-6 safety precautions, 6-5 save mode, 1-12 types, 6-3 Battery pack, 1-5, 1-17, 2-6 additional, 8-15 replacing, 6-12 BIOS Setup, 7-8 Bluetooth, 1-9, 4-34 Bluetooth Stack for Windows by Toshib
Index DVD-ROM&CD-R/RW drive, 1-6 using, 4-11 writing, 4-15 Front operation buttons, 1-11, 2-7 location, 2-7 Function keys, 5-2 E G Environment, 3-1 Equipment checklist, 1-1 Equipment setup general conditions, 3-2 placement, 3-3 Ergonomics lighting, 3-5 seating and posture, 3-4 work habits, 3-5 Execute-Disable Bit Capability, 7-8 External monitor, 1-8, 2-5, 8-16 port location, 2-4 Graphics controller, 1-7 F Fingerprint Utility, 1-14 Fingerprint Sensor location, 4-1 problems, 9-15 using, 4-2 Floppy dis
Index Indicators, 2-9, 6-2 Arrow mode, 2-10 Battery, 2-9 Bridge Media, 2-9 DC IN, 2-9 HDD, 2-9 Numeric mode, 2-10 Power, 2-9 Wireless communication, 2-9 K Keyboard, 1-8, 5-1 emulating enhanced keyboard, 5-2 Fn Sticky key, 5-6 Function keys F1...
Index PC card, 1-8 eject button location, 2-2 inserting, 8-2 problems, 9-12 removing, 8-3 slot location, 2-2 Pointing Device Touch Pad, 1-8, 2-8, 4-1 Touch Pad control buttons, 2-7, 4-1 Touch Pad control buttons location, 2-7 Touch Pad location, 2-7 using, 4-1 Ports external monitor, 1-8 i.
Index Soft keys enhanced keyboard, 5-2 Enter, 5-3 right Ctrl key, 5-3 ScrLock, 5-3 Sound drivers, 1-16 Sound system, 1-8, 4-28 headphone jack, 1-8, 2-2 microphone, 2-2 microphone jack, 1-8, 2-2 mute hot keys, 5-3 Stereo speakers, 2-7 volume control, 2-5 Standby, 1-13 setting, 3-10 System automatic, 1-11 Stereo speakers location, 2-7 System indicators location, 2-1 V Video modes, B-1 Video RAM, 1-5 Volume control, 2-5 location, 2-4 W Wireless communication, 4-33 indicator, 2-9, 4-36 Wireless communication
Index Index-6 User’s Manual
