User's Manual Z30/Z40-B
Table of Contents Chapter 1 TOSHIBA Legal, Regulatory, and Safety Copyright, Disclaimer and Trademarks .............................................. 1-1 Regulatory Information ......................................................................... 1-2 Video Standard Notice .......................................................................... 1-8 ENERGY STAR® Program .................................................................... 1-9 Disposing of the computer and the computer's battery ........
Sound System and Video mode ......................................................... 4-29 Chapter 5 Utilities and Advanced Usage Utilities and Applications ...................................................................... 5-1 Special features ..................................................................................... 5-3 Using the TOSHIBA Sleep Utility ......................................................... 5-5 TOSHIBA Password Utility .....................................................
Chapter 1 TOSHIBA Legal, Regulatory, and Safety This chapter states the legal, regulatory, and safety information applicable to TOSHIBA computers. Copyright, Disclaimer and Trademarks Copyright © 2014 TOSHIBA Corporation. All rights reserved. Under the copyright laws, this manual cannot be reproduced in any form without the prior written permission of TOSHIBA. No patent liability is assumed, with respect to the use of the information contained herein.
The Bluetooth® word mark and logos are registered trademarks owned by Bluetooth SIG, Inc. and any use of such marks by Toshiba Corporation and its affiliates is under license. The terms HDMI and HDMI High-Definition Multimedia Interface, and the HDMI Logo are trademarks or registered trademarks of HDMI Licensing LLC in the United States and other countries. DTS, the Symbol, & DTS and the Symbol together are registered trademarks and DTS Studio Sound is a trademark of DTS, Inc. © DTS, Inc.
recommended by TOSHIBA is likely to result in interference to radio and TV reception. Shielded cables must be used between the external devices and the computer’s external RGB monitor port, Universal Serial Bus (USB 3.0) ports, HDMI out port and Headphone/Microphone jack. Changes or modifications made to this equipment, not expressly approved by TOSHIBA or parties authorized by TOSHIBA could void the user’s authority to operate the equipment.
EC in case of implemented telecommunication accessories and the Low Voltage Directive 2006/95/EC for the supplied power adapter. Furthermore the product complies with the Ecodesign Directive 2009/125/EC (ErP) and its related implementing measures. This product and the original options are designed to observe the related EMC (Electromagnetic Compatibility) and safety standards.
Canadian regulatory information (Canada only) This digital apparatus does not exceed the Class B limits for radio noise emissions from digital apparatus as set out in the Radio Interference Regulation of the Canadian Department of Communications. Note that Canadian Department of Communications (DOC) regulations provide, that changes or modifications not expressly approved by TOSHIBA Corporation could void your authority to operate this equipment.
Disposal of batteries and/or accumulators The crossed out wheeled dust bin symbol indicates that batteries and/or accumulators must be collected and disposed of separately from household waste. If the battery or accumulator contains more than the specified values of lead (Pb), mercury (Hg), and/or cadmium (Cd) defined in the European Battery Directive, then the chemical symbols for lead (Pb), mercury (Hg) and/or cadmium (Cd) will appear below the crossed out wheeled dust bin symbol.
Following information is only for Turkey: Disposal of products: The crossed wheelie bin symbol means that this product should not be collected and disposed with other household wastes. When product become waste at the end-of-life, to protect environment and human health, it should be given to nearest collection recycling or disposal center. For more information about collection and recycling programs in your country please contact your local authority or the retailer where the product was purchased.
Video Standard Notice THIS PRODUCT IS LICENSED UNDER THE AVC, THE VC-1 AND MPEG-4 VISUAL PATENT PORTFOLIO LICENSE FOR THE PERSONAL AND NON-COMMERCIAL USE OF A CONSUMER FOR (I) ENCODING VIDEO IN COMPLIANCE WITH THE ABOVE STANDARDS ("VIDEO") AND/OR (II) DECODING AVC, VC-1 AND MPEG-4 VIDEO THAT WAS ENCODED BY A CONSUMER ENGAGED IN A PERSONAL AND NONCOMMERCIAL ACTIVITY AND/OR WAS OBTAINED FROM A VIDEO PROVIDER LICENSED BY MPEG LA TO PROVIDE SUCH VIDEO.
ENERGY STAR® Program Your Computer model may be ENERGY STAR® compliant. If the model you purchased is compliant, it uses the Energy Star logo and the following information applies. TOSHIBA is a partner in the ENERGY STAR Program and has designed this computer to meet the latest ENERGY STAR guidelines for energy efficiency.
observed to further reduce the risk of personal injury or damage to the computer. Be certain to read the following general precautions and to note the cautions included in the text of the manual. Provide adequate ventilation Always make sure that your computer and AC adaptor have adequate ventilation and are protected from overheating when the power is turned on or when an AC adaptor is connected to a power outlet (even if your computer is in Sleep Mode).
Heat injury Avoid prolonged physical contact with the computer. If the computer is used for long periods, its surface can become very warm. While the temperature will not feel hot to the touch, if you maintain physical contact with the computer for a long time, for example if you rest the computer on your lap or if you keep your hands on the palm rest, your skin might suffer a low-heat injury.
Make sure all disk/disc activity has ended before moving the computer. Turn off (shut down) the computer. Disconnect the AC adaptor and all peripherals before moving the computer. Close the display panel. Do not pick up the computer by its display panel. Before carrying your computer, shut it down, disconnect the AC adaptor and allow it to cool down. A failure to follow this instruction might result in minor heat injury.
A caution informs you that improper use of equipment or failure to follow instructions might cause data loss, equipment damage, or might result in minor or moderate injury. Please read. A note is a hint or advice that helps you make best use of your equipment.
Chapter 2 Getting Started This chapter provides an equipment checklist, and basic information to start using your computer. If you use an operating system that was not pre-installed by TOSHIBA, some of the features described in this manual might not function properly. Equipment checklist Carefully unpack your computer, taking care to save the box and packaging materials for future use.
Right-click Tap the Touch Pad with two fingers together or click the right Touch Pad control button once. Right-click the mouse once. Press and hold on the touch screen (only for touch screen models). Double-click Tap the Touch Pad or click the left Touch Pad control button twice. Left-click the mouse twice. Tap the touch screen twice (only for touch screen models).
Opening the display Turning on the power Initial setup Getting to know Windows Use a virus-check program and make sure that it is updated regularly. Never format storage media without checking its content - formatting destroys all stored data. It is a good idea to back up the internal storage drive or other main storage device to external media periodically. General storage media is not durable or stable over long periods of time and under certain conditions might result in data loss.
Do not use a 3-pin to 2-pin conversion plug. When you connect the AC adaptor to the computer, always follow the steps in the exact order as described in this User’s Manual. Connecting the power cable to a live electrical outlet should be the last step otherwise the adaptor DC output plug might hold an electrical charge and cause an electrical shock or minor bodily injury when touched. As a general safety precaution, avoid touching any metal parts.
Figure 2-3 Connecting the DC output plug to the computer (Z30-B) 1 2 Figure 2-4 Connecting the DC output plug to the computer (Z40-B) 1 2 1. DC IN 19V jack 2. DC output plug Product appearance depends on the model you purchased. Opening the display The display panel can be opened to a wide range of angles for optimal viewing. While holding down the palm rest with one hand so that the main body of the computer is not raised, slowly lift the display panel.
Be careful not to open the display panel too far as this might put stress on the display panel’s hinges and cause damage. Do not press or push on the display panel. Do not lift the computer by the display panel. Do not close the display panel with pens or any other objects left in between the display panel and the keyboard.
Figure 2-7 Turning on the power (Z40-B) 1 1. Power button Product appearance depends on the model you purchased. Initial setup The Windows Startup Screen is the first screen displayed when you turn on the power. To install the operating system properly, follow the on-screen instructions on each screen. When it is displayed, be sure to read the License Terms carefully. Turning off the power The power can be turned off in one of the following modes, either Shut Down Mode, Sleep Mode or Hibernation Mode.
Do not turn the computer or peripheral devices back on immediately. Wait a short period to avoid any potential damage. Restarting the computer Certain conditions require that you reset the computer, for example if: You change certain computer settings. To restart the computer, there are two ways this can be achieved: Click Start. Point to the arrow ( ) beside the Shut down button and then select Restart.
To restore the operation of the computer from Sleep Mode, press and hold the power button or any key on the keyboard for a short amount of time. Note that keyboard keys can only be used if the Wake-up on Keyboard option is enabled within the TOSHIBA HWSetup. If the computer enters Sleep Mode while a network application is active, the application might not be restored when the computer is next turned on and the system returns from Sleep Mode.
Hibernation Mode The Hibernation Mode feature saves the contents of memory to the internal storage drive when the computer is turned off so that, the next time it is turned on, the previous state is restored. Note that the Hibernation Mode feature does not save the status of any peripheral devices connected to the computer. Save your data. While entering Hibernation Mode, the computer saves the contents of memory to the internal storage drive. However, for safety sake, it is best to save your data manually.
Data save in Hibernation Mode When you turn off the power in Hibernation Mode, the computer takes a moment to save the current data in memory to the internal storage drive. After you turn off the computer, and the content of memory has been saved to the internal storage drive, turn off the power to any peripheral devices. Do not turn the computer or devices back on immediately. Wait a moment to let all capacitors fully discharge.
Chapter 3 The Grand Tour This chapter identifies the various components of the computer. It is recommended that you become familiar with each before you operate the computer. Legal Footnote (Non-applicable Icons) For more information regarding Non-applicable Icons, refer to the Legal Footnotes section. Handle your computer carefully to avoid scratching or damaging the surface.
DC IN/Battery indicator The DC IN/Battery indicator shows the condition of the DC IN and the battery charge status. White indicates the battery is fully charged while the power is being correctly supplied from the AC power adaptor. Refer to the Power Condition Descriptions section for more information on this feature. Power indicator The Power indicator normally glows white when the computer is turned on. However, if you turn off the computer into Sleep Mode, this indicator flashes amber.
Figure 3-2 The left side of the computer (Z30-B) 1 2 3 1. DC IN 19V jack 2. External RGB monitor port 3. HDMI out port* 4 5 6 4. Universal Serial Bus (USB 3.0) port 5. Headphone/Microphone jack 6. Smart Card slot* * Provided with some models. Product appearance depends on the model you purchased. DC IN 19V jack The AC adaptor connects to this jack to power the computer and charge its internal batteries.
Before removing a USB device from the USB port of your computer, click the Safely Remove Hardware and Eject Media icon on the Windows Taskbar, and then select the USB device that you want to remove. Keep foreign metal objects, such as screws, staples, and paper clips, out of the USB port. Foreign metal objects can create a short circuit, which can cause damage and fire, possibly resulting in serious injury. Headphone/ Microphone jack A 3.
SIM Card slot This slot allows you insert a SIM card which enables a high-speed access to the Internet, corporate Intranet and your email while you are away from office. Refer to the Wireless WAN device section for more information. Universal Serial Bus (USB 3.0) port Two Universal Serial Bus ports, which comply to the USB 3.0 standard, are provided on the right side of the computer. The USB 3.0 port is compliant with USB 3.0 standard and backward compatible with USB 2.0 devices. USB 3.
Back (Z30-B) The following figure shows the back of the computer. Figure 3-4 The back of the computer (Z30-B) 1 1. Cooling vents Product appearance depends on the model you purchased. Cooling vents The cooling vents help the processor to avoid overheating. Do not block the cooling vents. Keep foreign metal objects, such as screws, staples and paper clips, out of the cooling vents. Foreign metal objects can create a short circuit, which can cause damage and fire, possibly resulting in serious injury.
Docking port This port enables connection of an optional TOSHIBA Hi-Speed Port Replicator III 180W/ 120W described in TOSHIBA Hi-Speed Port Replicator III 180W/120W. Some models are equipped with the docking port. Only the TOSHIBA Hi-Speed Port Replicator III 180W or 120W is compatible with the docking port. Do not attempt to use any other Port Replicator. Keep foreign objects out of the docking port. A pin or similar object can damage the circuitry of the computer.
Figure 3-6 The front of the computer with the display panel open (Z30-B) 3 1 2 4 2 5 6 8 9 6 7 10 10 11 12 13 14 16 1. Wireless communication antennas (not shown)* 2. Microphone* 3. Web Camera LED* 4. Web Camera* 5. Display screen 6. Display hinges 7. Keyboard 8. Power button 9. AccuPoint* 14 17 18 15 10. AccuPoint control buttons* 11. Touch Pad ON/OFF indicator 12. TOSHIBA eco indicator 13. Touch Pad 14. Touch Pad control buttons 15. Fingerprint Sensor* 16. DC IN/Battery indicator 17.
Microphone The built-in microphone allows you to record sounds for your application. Refer to the Sound System and Video mode section for more information. Web Camera LED The Web Camera LED glows when the Web Camera is operating. Web Camera Web Camera is a device that allows you to record video or take photographs with your computer. You can use it for video chatting or video conferences using a communication tool. Some models are equipped with a Web Camera.
AccuPoint A pointer control device located in the center of the keyboard is used to control the on-screen pointer. Some models are equipped with an AccuPoint. AccuPoint control buttons Control buttons below the keyboard let you select menu items or manipulate text and graphics designated by the on-screen pointer. Only models equipped with an AccuPoint are equipped with AccuPoint control buttons. Touch Pad ON/OFF indicator Double tap this indicator to enable/disable the Touch Pad.
Power indicator The Power indicator normally glows white when the computer is turned on. However, if you turn the computer off into Sleep Mode, this indicator flashes amber. Internal storage drive The Internal storage drive indicator blinks indicator white whenever the computer is accessing the internal storage drive. The Grand Tour for Z40-B Front with the display closed (Z40-B) The following figure shows the front of the computer with the display panel in the closed position.
Internal storage drive The Internal storage drive indicator blinks indicator white whenever the computer is accessing the internal storage drive. Wireless communication indicator The Wireless communication indicator glows amber when the Wireless functions are turned on. Some models are equipped with Wireless functions. Wireless WAN/WiMAX The Wireless WAN/WiMAX indicator glows indicator blue when the Wireless WAN/WiMAX functions are turned on.
Universal Serial Bus (USB 3.0) port One Universal Serial Bus port, which complies to the USB 3.0 standard, is provided on the left side of the computer. The USB 3.0 port is compliant with USB 3.0 standard and backward compatible with USB 2.0 devices. USB 3.0 port(s) might work as USB 2.0 port(s) when operating in USB Legacy Emulation mode. Note that it is not possible to confirm the operation of all functions of all USB devices that are available.
Right side (Z40-B) The following figures show the right side of the computer. Figure 3-9 The right side of the computer (Z40-B) 1 2 1. Smart Card slot* 2. Headphone/Microphone jack 3. Universal Serial Bus (USB 3.0) ports 3 3 4 5 6 4. LAN jack 5. DC IN 19V jack 6. Security lock slot * Provided with some models. Product appearance depends on the model you purchased. Smart Card slot This slot allows you to install a Smart Card device. Some models are equipped with a Smart Card slot.
Keep foreign metal objects, such as screws, staples, and paper clips, out of the USB port. Foreign metal objects can create a short circuit, which can cause damage and fire, possibly resulting in serious injury. LAN jack This jack lets you connect to a LAN. The adaptor has built-in support for Ethernet LAN (10 megabits per second, 10BASE-T), Fast Ethernet LAN (100 megabits per second, 100BASE-TX) or Gigabit Ethernet LAN (1000 megabits per second, 1000BASE-T). Refer to Operating Basics, for details.
Figure 3-11 The underside of the computer (Z40-B) 2 1. Cooling vents 1 2. Docking port* * Provided with some models. Product appearance depends on the model you purchased. Cooling vents The cooling vents help the processor to avoid overheating. Docking port This port enables connection of an optional TOSHIBA Hi-Speed Port Replicator III 180W/ 120W described in TOSHIBA Hi-Speed Port Replicator III 180W/120W. Some models are equipped with the docking port.
Figure 3-12 The front of the computer with the display panel open (Z40-B) 2 3 4 2 1 5 6 9 6 8 10 10 11 12 7 13 14 16 14 17 18 15 1. Wireless communication antennas (not shown)* 2. Microphone* 3. Web Camera LED* 4. Web Camera* 5. Display screen 6. Display hinges 7. Keyboard 8. Power button 9. AccuPoint 10. AccuPoint control buttons 11. Touch Pad ON/OFF indicator 12. TOSHIBA eco indicator 13. Touch Pad 14. Touch Pad control buttons 15. Fingerprint Sensor* 16. DC IN/Battery indicator 17.
Web Camera LED The Web Camera LED glows when the Web Camera is operating. Web Camera Web Camera is a device that allows you to record video or take photographs with your computer. You can use it for video chatting or video conferences using a communication tool. Some models are equipped with a Web Camera. Do not point the web camera directly at the sun. Do not touch or press strongly on the web camera lens. Failure to do so might reduce image quality.
Touch Pad ON/OFF indicator Double tap this indicator to enable/disable the Touch Pad. The indicator for some models shows the status of the Touch Pad: Enabled: off Disabled: glows white TOSHIBA eco indicator Double tap this indicator to launch the TOSHIBA eco Utility. Touch Pad The Touch Pad located in the palm rest is used to control the movement of the on-screen pointer. To use the Touch Pad, simply touch and move your fingertip across it in the direction you want the on-screen pointer to go.
Internal Hardware Components This section describes the internal hardware components of your computer. The actual specifications might vary depending on the model you purchased. Battery pack This computer includes a battery pack inside. However, do not attempt to dismount or replace it by yourself. Contact an authorized TOSHIBA service provider, if necessary. The rechargeable lithium-ion battery pack provides power to the computer when the AC adaptor is not connected.
Under certain unusual conditions of prolonged non-use and/or exposure to high temperatures, the SSD might be vulnerable to data retention errors. Legal Footnote (Internal Storage Drive Capacity) For more information regarding internal storage drive capacity, refer to the Legal Footnotes section. Video RAM The memory in the graphics adaptor of the computer, used to store the image displayed on a bitmap display. The amount of Video RAM available depends on the system memory of the computer.
Use the default setting for NVIDIA Optimus technology. If the program does not run normally after the setting has been changed, restore the program to the default setting. If the program does not run normally, restore the Preferred graphics processor to the default setting. When you use some video playback programs to play video files, the preferred graphics processor in the "Program Settings" tab cannot be changed to the graphics other than "Integrated Graphics".
If you want to enable this feature, click Enable under Display Power Saving Technology. Power Condition Descriptions The computer operating capability and battery charge status are affected by different power conditions, including whether an AC adaptor is connected and what the battery charge level is. DC IN/Battery indicator Check the DC IN/Battery indicator to determine the status of the battery pack and the power status with the AC adaptor connected.
Chapter 4 Operating Basics This chapter describes the basic operations of your computer, and highlights the precautions that must be taken when using it. Using the Touch Screen Some models are equipped with a touch screen. You can use your finger to manipulate icons, buttons, menu items, the onscreen keyboard, and other items on the touch screen. Tap Simply tap your finger on the touch screen to act on items on the screen.
Tap Simply tap your finger on the Touch Pad to act on items on the screen. (Similar to left-click) Pinch or stretch Place two or more fingers down on the Touch Pad and move them toward each other (pinch) or away from each other (stretch). This visually zooms in or out. Two-Finger Scroll Place two fingers down and slide them vertically or horizontally from anywhere on the Touch Pad. This allows you to operate the scroll bars of a window.
Figure 4-1 CAPS LOCK indicator 1 1. CAPS LOCK indicator Product appearance depends on the model you purchased. CAPS LOCK This indicator glows green when letter keys are locked into their uppercase format. Function Key The function keys (F1 ~ F12) are the 12 keys at the top of your keyboard. Function keys let you enable or disable certain features of the computer. The functions can be performed by pressing the associated function keys. Key Combination Function FN + F1 Enters ''Lock computer mode''.
Key Combination Function FN + F11 Turns on Numeric Mode. FN + F12 Locks the cursor on a specific line. FN + ESC Turns the sound on or off. FN + Space Changes the display resolution. FN + 1 Reduces the icon size on the desktop or the font sizes within one of the supported application windows. FN + 2 Enlarges the icon size on the desktop or the font sizes within one of the supported application windows. FN + 3 Decreases the volume of the computer. FN + 4 Increases the volume of the computer.
3. Press the function key repeatedly to cycle through the available options and release the FN key when the desired option is selected. You can also click the desired option. For more information, refer to the TOSHIBA Flash Cards Help file. To access this help, click Start -> All Programs -> TOSHIBA -> Tools & Utilities -> Flash Cards.In the Settings for Flash Cards window, click the Help button.
Replacing the cap The AccuPoint cap is an expendable item that should be replaced after prolonged use. The spare AccuPoint cap is supplied with some models. 1. To remove the AccuPoint cap, gently dig the cap out (with finger). Figure 4-2 Removing the AccuPoint cap (Z30-B) 1 1. AccuPoint cap Product appearance depends on the model you purchased. 2. Position a new cap on the peg and press it into place. The peg is square, so be careful to align the cap’s square hole with the peg.
Align the first joint of the finger to the center of the sensor. Lightly touch the sensor and swipe finger levelly towards you until the sensor surface becomes visible. In performing this process, you should also take care to ensure that the center of your fingerprint is on the sensor. The following illustrations show the recommended way to swipe your finger over the fingerprint sensor. Figure 4-3 Swipe the finger 1 1 1.
Observe the following before you place your finger on the sensor whether for fingerprint enrollment/registration or recognition. Wash and dry your hands thoroughly. Remove static electricity from your fingers by touching any metal surface. Static electricity is a common cause of sensor failures, especially when the weather is dry. Clean the sensor with a lint-free cloth. Do not use detergent or any other chemicals to clean the sensor.
Also refer to the fingerprint utility Help file for more information by clicking ? in TOSHIBA Fingerprint Utility main menu. Fingerprint utility limitations TOSHIBA does not guarantee that the fingerprint utility technology will be completely secure or error-free, or that it will accurately screen out unauthorized users at all times. TOSHIBA is not liable for any failure or damage that might arise out of the use of the fingerprint software.
It is strongly recommended that you register 2 or more fingerprints. You cannot enroll the same fingerprint more than once, even on a different user account. Delete the Fingerprint Data Saved fingerprint data is stored in special non-volatile memory inside the fingerprint sensor. Therefore, if you give the computer to someone else, or dispose of it in any way, please uninstall the application or delete all the logs created by the application. Delete the fingerprint data for the currently logged in user 1.
This is useful especially when many users are using the PCs, as user selection can be skipped. Fingerprint Authentication Procedure 1. 2. Start up the computer. The Logon Authorization screen is displayed. Choose any of the enrolled fingers and swipe the fingerprint on the sensor. If authentication is successful, the user will be logged on to Windows. If the fingerprint authentication fails, please logon using the Windows logon password.
It is necessary to register the User/BIOS Password and Windows Logon Password before using the Fingerprint Pre-Boot authentication and this Fingerprint Single Sign-On Feature. Use the TOSHIBA Password Utility to register your User/BIOS Password. If Windows Logon is not the default for your system, see Manual to register your Windows Logon Password. Only one fingerprint authentication is required to replace the User/BIOS Password (and, if applicable, the HDD/SSD Password) and the Windows Logon Password.
Real-Time Clock (RTC) function The Real-Time Clock (RTC) function is supported. The battery pack provides power for the internal real-time clock and calendar function and also maintains the system configuration while the computer is turned off. If the RTC lasting time completely runs out, the system will lose this information and the real-time clock and calendar will stop working. You can change the Real-Time Clock settings in the BIOS setup utility. Refer to Troubleshooting for further information.
The battery is extremely hot or cold (if the battery is extremely hot, it might not charge at all). To ensure the battery charges to its full capacity, charge it at room temperature of between 5°C to 35°C (41 95°F). The battery is nearly completely discharged. In this instance, leave the AC adaptor connected for a few minutes and the battery should begin charging.
System Sleep Mode System Hibernation Mode Display power off period Internal storage drive power off period How often and for how long you use the internal storage drive and external disk drives, for example, optical disc How much charge the battery contained to begin with How you use optional devices, such as a USB device, to which the battery supplies power Where you store your programs and data Whether you close the display panel when you are not using the keyboard - closing the display saves power The en
Wireless WAN Device Some models are equipped with the Wireless WAN device. This device gives you the ability for a high-speed connection to the Internet, corporate intranet, and your email while you are away from the office. Installing a SIM card To install a SIM card, do the following: 1. 2. 3. 4. Click Start and then select Shut down. Remove the AC adaptor and all cables and peripherals connected to the computer. Locate the SIM card slot.
Figure 4-6 Installing the SIM Card (Z30-B) 3 1 2 Figure 4-7 Installing the SIM Card (Z40-B) 1 3 1. SIM card slot 2. SIM card 2 3. SIM card tray Never allow metal objects, such as screws, staples and paper clips, to enter the computer. Foreign metal objects can create a short circuit, which can cause computer damage and fire, possibly resulting in serious injury. Do not touch the connectors on the SIM card or on the computer. Debris on the connectors might cause access problems.
Your current location might not be shown depending on the status of GPS or the location. If you are obtaining your current location information from the computer, your current location might not be detected due to the information accuracy.
Connecting the LAN cable To connect the LAN cable, do the following: Connect the AC adaptor before connecting the LAN cable. The AC adaptor must remain connected during LAN use. If you disconnect the AC Adaptor while the computer is accessing a LAN, the system might hang up. Do not connect any other cable to the LAN jack except the LAN cable. Otherwise, malfunctions or damage might occur. Do not connect any power supplying device to the LAN cable that is connected to the LAN jack.
An adaptor is required to use miniSD/microSD Card. Not all memory media have been tested and verified to work correctly. Therefore, it is not possible to guarantee that all memory media can operate properly.
Formatting a memory media card Memory media cards are sold already formatted in conformity to specific standards. If you reformat a memory card, be sure to reformat it with a device such as digital camera or digital audio player that uses the memory cards, not with the format command provided within Windows. To format all areas of the memory card, including the protected area, you must obtain an appropriate application that applies the copy protection system.
Inserting memory media The following instructions apply to all types of supported media devices. To insert memory media, do the following: 1. 2. 3. Turn the memory media so that the contacts (metal areas) face down. Insert the memory media into the memory media slot on your computer. Press the memory media gently until it clicks into place. Figure 4-10 Inserting memory media (Z30-B) 1 2 1. Memory media slot 2. Memory media Product appearance depends on the model you purchased.
Do not remove the memory media while the computer is in Sleep or Hibernation Mode. The computer might become unstable or data in the memory media might be lost. Do not remove only the miniSD/microSD Card while leaving the adaptor in the memory media slot. Smart Card A Smart Card is a credit card sized plastic card. An extremely thin integrated circuit (IC chip) is embedded into the card on which information can be recorded.
3. After inserting the Smart Card, you should refer to its documentation and also check the configuration in Windows to ensure that it is correct. Removing a Smart Card To remove a Smart Card, do the following: 1. Click the Safely Remove Hardware and Eject Media icon on the Windows Taskbar. Before removing the Smart Card, confirm that the Smart Card is not working with any program or system. Be careful not to bend the Smart Card while removing it from the computer. 2. 3.
Figure 4-11 Connecting the RGB cable to the External RGB monitor port (Z30-B) 1 2 1. External RGB monitor port 2. RGB cable Product appearance depends on the model you purchased. When you turn on the power, the computer automatically recognizes the monitor and determines whether it is a color or monochrome device. When displaying desktop on an external RGB monitor, desktop is sometimes displayed on the center of the monitor with black bars around desktop (with small size).
Figure 4-12 Connecting the HDMI out port (Z30-B) 1 2 1. HDMI out port 2. HDMI cable Product appearance depends on the model you purchased. Do not plug/unplug an HDMI device under the following conditions: The system is starting up. The system is shutting down. When you connect a television or external monitor to the HDMI port, the display output device is set to HDMI. When you unplug the HDMI cable and replug it, wait at least 5 seconds before you replug the HDMI cable again.
You can also manually manage how the external displays work and change ) the display settings by pressing P while holding down the Windows ( key. If you disconnect the external display before you turn off the computer's power, be sure to switch to the internal display. When you change the display output device, the audio playback device might not switch automatically.
1. Align the top left and top right corner of your computer to the correct mark on the Port Replicator. Short Name 2. Top Left Corner Top Right Corner Z30-B A AB Z40-B B AB Press down on the back of the computer until it clicks into place. The computer connector on the port replicator engages the computer’s docking port. When the computer is connected, the Docked light on the Port Replicator glows green while the computer is powered on.
Security lock A security lock enables you to anchor your computer to a desk or other heavy object in order to help prevent unauthorized removal or theft. The computer has a security lock slot into which you can attach one end of the security cable, while the other end attaches to a desk or similar object. The methods used for attaching security cables differ from product to product. Refer to the instructions for the product you are using for more information.
Volume Mixer The Volume Mixer utility lets you control the audio volume for playback of devices and applications under Windows. To launch the Volume Mixer utility, right-click on the speaker icon on the Windows Taskbar, and then select Open Volume Mixer from the sub menu. To adjust the volume level of speakers or headphones, move the Speakers slider. To adjust the volume level of an application that you are using, move the slider for the corresponding application.
Dialog enhancement for clear and intelligible vocals Bass enhancement for rich, low frequency production High frequency definition for crisp details Consistent volume level across content To access the utility, click Start -> All Programs -> DTS, Inc -> DTS Studio Sound. U.S. patents apply to this product. See http://patents.dts.com.Manufactured under license from DTS Licensing Limited. Realtek HD Audio Manager You can confirm and change the audio configuration using the Realtek HD Audio Manager.
2. 3. Double-click on the circle button in the right side of the Realtek HD Audio Manager main screen. Select one from the device list for the device you plugged into. Video mode Video mode settings are configured via the Screen Resolution dialog. To open the Screen Resolution dialog, click Start -> Control Panel -> Appearance and Personalization -> Display -> Change display settings.
Chapter 5 Utilities and Advanced Usage This chapter describes the utilities and special features of this computer, and the advanced usage of some utilities. Utilities and Applications This section describes the pre-installed utilities that come with the computer and details how to start them. For further information on their operation, you may refer to each utility's online manual, help files or README.TXT file (if applicable).
TOSHIBA Accessibility The TOSHIBA Accessibility utility provides support to movement impaired users when they need to use the function keys. In use, the utility allows you to make the FN key "sticky", that is, you can press it once, release it, and they press one of the function keys in order to access its specific function. When set, the FN key remains active until another key is pressed.
TOSHIBA Service Station This application allows your computer to automatically search for TOSHIBA software updates or other alerts from TOSHIBA that are specific to your computer system and its programs. When enabled, this application periodically transmits to our servers a limited amount of system information, which will be treated in strict accordance with the rules and regulations as well as applicable data protection law.
Display automatic power off *1 This feature automatically cuts off power to the computer's display panel when there is no keyboard input for a specified time, with power being restored the next time a key is pressed. This can be specified in the Power Options. Internal storage drive This feature automatically cuts off power to the automatic power off *1 internal storage drive when it is not accessed for a specified time, with power being restored when the internal storage drive is next accessed.
Hibernation Mode This feature lets you turn off the power to the computer without exiting from your software. The contents of main memory are automatically saved to the Solid State Drive so that when you next turn the power on again, you can continue working right where you left off. Refer to the Turning off the power section, for more details. USB Wakeup function This function restores the computer from Sleep Mode depending on the external devices connected to the USB ports.
Sleep and Charge Your computer can supply USB bus power (DC5V) to the USB port even when the power of the computer is turned OFF. "Power OFF" includes Sleep Mode, Hibernation Mode, or shutdown state. This function can be used for ports that support the Sleep and Charge function. The port with the icon ( ) has Sleep and Charge function. You can use the Sleep and Charge function to charge certain USBcompatible external devices such as mobile phones or portable digital music players.
Metal paper clips or hair pins/clips can generate heat if they come into contact with USB ports. Do not allow USB ports to come into contact with metal products, for example when carrying the computer in your bag. Starting the TOSHIBA Sleep Utility To start the utility, click Start -> All Programs -> TOSHIBA -> Tools & Utilities -> Sleep Utility. Enabling Sleep and Charge This utility can be used to enable and disable the Sleep and Charge function.
User Password To start the utility, click the following items: Start -> All Programs -> TOSHIBA -> Tools & Utilities -> Password Utility -> User Password User authentication might be required to validate user rights when using TOSHIBA Password Utility to delete or change passwords, etc. Set (button) Click this button to register a password. After a password is set, you are prompted to enter it when you start the computer.
If you forget your HDD/SSD User Password, TOSHIBA will NOT be able to assist you, and your internal storage drive will be rendered COMPLETELY and PERMANENTLY INOPERABLE. TOSHIBA will NOT be held responsible for any loss of any data, any loss of use or access to your internal storage drive, or for any other losses to you or any other person or organization that result from the loss of access to your internal storage drive. If you cannot accept this risk, do not register the HDD/SSD User Password.
3. Press ENTER. If you enter the password incorrectly three times in a row, or if you do not enter the password within 1 minute, the computer shuts off. In this case, some features that can power on the computer automatically (Wake-up on LAN, Task Scheduler, etc) might not work. You must turn the computer back on to retry password entry. TOSHIBA HWSetup TOSHIBA HWSetup is the TOSHIBA configuration management tool available through the Windows operating system.
The settings or options explained here might vary depending on the model you purchased. After you changed the settings, a dialog box might appear to prompt you that the changes will take effect after the computer restarts. Make sure to restart your computer immediately to apply these changes.
Starting the TOSHIBA PC Health Monitor The TOSHIBA PC Health Monitor can be opened by clicking Start -> All Programs -> TOSHIBA -> Support & Recovery -> PC Health Monitor. The TOSHIBA PC Health Monitor main screen is displayed. This utility might be disabled by default on your computer. You can enable it by clicking Please click here to enable TOSHIBA PC Health Monitor. The "PC Health Monitor Software Notice & Acceptance" screen is displayed. Carefully read the information displayed.
HDD Protection You can enable or disable HDD Protection by moving the slider to the right or left. HDD Protection does not work when the computer is booting, in Sleep Mode, in Hibernation Mode, in transition to Hibernation Mode, recovering from Hibernation Mode, or powered off. Do not subject the computer to vibration or impact while the protection is disabled. HDD Protection Message Move the slider to the right to enable notification when viberation is detected.
Detection Level Amplification When the AC adaptor is disconnected, HDD Detection assumes that the computer will be carried and sets the detection level to the maximum for 10 seconds. Default You can reset HDD Protection settings to factory default by first clicking Default button and then Apply button. 3D Viewer This feature displays a 3D object on the screen which moves in according to tilting or vibration of the computer.
System Recovery There is a hidden partition allocated on the internal storage drive for the System Recovery Options in the event of a problem. You can also create recovery media and restore the system.
Do not write to the media when the virus check software is running. Wait for it to finish, then disable virus detection programs including any software that checks files automatically in the background. Do not use utilities, including those intended to enhance internal storage drive access speed. They might cause unstable operation and damage data. Do not shut down/log off or Sleep/Hibernate while writing or rewriting the media.
When you reinstall the Windows operating system, the internal storage drive will be reformatted and all data will be lost. 1. 2. 3. 4. 5. Load the Recovery Media into the external Optical Disc Drive or insert the recovery USB Flash Memory into one available USB port. Click Start. Point to the arrow ( ) beside the Shut down button and, then select Restart. Hold down the F12 key, and release this key one second after the computer is power on.
1. 2. 3. User's Manual Click Start. Point to the arrow ( ) beside the Shut down button and, then select Restart. While holding down 0 (zero) key on the keyboard, turn on your computer. Follow the on screen instructions to finish the recovery.
Chapter 6 Troubleshooting TOSHIBA has designed this computer for durability, however, should problems occur you are able to use the procedures detailed in this chapter to help determine the cause. You should become familiar with this chapter as knowing what might go wrong can help prevent problems from occurring in the first place. Problem-solving process If you observe the following guidelines, resolving problems will be much easier.
Check all cables to ensure that they are correctly and firmly attached to the computer - loose cables can cause signal errors. Inspect all connecting cables for loose wires and all connectors for loose pins. Check that your disc media is correctly loaded Always try to make detailed notes of your observations and keep them in a permanent error log - this helps you to describe your problems to TOSHIBA Support. In addition, if a problem recurs, the log you have made helps to identify the problem faster.
Hardware If you cannot find a software problem, you should then check the setup and configuration of your hardware. First run through the items in the preliminary checklist as described previously then, if you still cannot correct the problem, try to identify the source. The next section provides checklists for individual components and peripherals.
If you are using the AC adaptor, check that the wall outlet is working by plugging in another device, such as a lamp. Verify that the computer is on by looking at the Power indicator. If the indicator is glowing, the computer is on. Also, try turning the computer off and then on. If you are using an AC adaptor, verify that the computer is receiving power from the external power source by looking at the DC IN/Battery indicator.
Problem Procedure AC adaptor does not Check the connections to make sure that the power the computer power cord/adaptor is firmly connected to the computer and a working power outlet. Check the condition of the cord and terminals. If the cord is frayed or damaged it should be replaced, while if the terminals are soiled, they should be cleaned with a clean cotton cloth. If the AC adaptor still does not power the computer, you should contact TOSHIBA Support.
Real-Time Clock Problem Procedure The BIOS setting and system date/ time are lost. The lasting time of the Real-Time Clock (RTC) has run out. You must set the date and time in the TOSHIBA Setup Utility by using the following steps: 1. Launch the TOSHIBA Setup Utility. 2. 3. 4. Refer to the TOSHIBA Setup Utility section for further information. Set the date in the System Date field. Set the time in the System Time field. Follow the on-screen instructions to proceed.
HDD Problem Procedure Slow performance The files on the HDD might be fragmented. In this instance, you should run the disk defragmentation utility to check the condition of your files and the HDD. Refer to the operating system's documentation or online Help File for further information on operating and using the defragmentation utility. As a last resort, you should reformat the HDD and then reload the operating system and all other files and data.
Touch Pad Problem Procedure The Touch Pad does Check the Device Select settings by the following not work. steps: 1. 2. On-screen pointer does not respond to pointing device operation In this instance, the system might be busy. Try moving the mouse again after waiting a short while. Double-tapping (Touch Pad) does not work In this instance, you should initially try changing the double-click speed setting within the Mouse Control utility. 1. 2. 3. The on-screen pointer moves too fast or too slow 1.
USB mouse Problem Procedure On-screen pointer does not respond to mouse operation In this instance, the system might be busy. Try moving the mouse again after waiting a short while. Remove the mouse from the computer and then reconnect it to a free USB port in order to ensure that it is firmly attached. Double-clicking does In this instance, you should initially try changing not work the double-click speed setting within the Mouse Control utility. 1. 2. 3.
Problem Procedure USB device does not Remove the USB device from the computer and work then reconnect it to a free port in order to ensure that it is firmly attached. Ensure that any required USB device drivers are properly installed. To achieve this, you should refer to both the device documentation and the operating system documentation. Sleep and Charge function For more information and settings, refer to the Sleep and Charge section. Problem Procedure I cannot use the Sleep and Charge function.
Problem Procedure External devices connected to the compatible ports do not work when connected to a compatible port. Some external devices might not work when connected to a compatible port if the Sleep and Charge function is enabled. The "USB Wakeup function" does not work. When "System ON CDP Charge Mode" or "USB Sleep and Charge function" is enabled, the "USB WakeUp" function does not work for ports that support the Sleep and Charge function.
External monitor Also refer to Operating Basics, and to the documentation supplied with your monitor for further information. Problem Procedure Monitor does not turn on After confirming that the monitor's power switch is on, check the connections to make sure that the power cord/adaptor is firmly connected to the monitor and to a working power outlet. No display Try adjusting the contrast and brightness controls on the external monitor.
Problem Procedure Wake-up on LAN does not work Make sure that the AC adaptor is connected. The Wake-up on LAN function consumes power even when the system is off. If problems persist, consult your LAN administrator. Wireless LAN Problem Procedure Cannot access Wireless LAN Make sure that the wireless communication function of the computer is on. If problems persist, contact your LAN administrator.
If a problem occurs when you are running software applications, consult the software documentation for troubleshooting suggestions and consider calling the software company's technical support department for assistance. Consult the reseller or dealer from where you purchased your computer and/or software - they are your best resource for current information and support.
Chapter 7 Appendix Specifications This section summarizes the technical specifications of the computer. Physical Dimensions The following physical dimensions do not include parts that extend beyond the main body. The physical dimensions might vary depending on the model you purchased. Z30-B 316 (w) x 227 (d) x 13.9/17.9 (h) millimeters 316 (w) x 227 (d) x 15.9/19.9 (h) millimeters (touch screen models) Z40-B 338 (w) x 236 (d) x 20.4 (h) millimeters 338 (w) x 236 (d) x 21.
Power Requirements AC adaptor 100-240V AC 50 Hz or 60 Hz (cycles per second) Computer 19 V DC External RGB monitor port pin assignment 5 1 15 11 10 6 Pin Signal Name Description I/O 1 CRV Red Video Signal O 2 CGV Green Video Signal O 3 CBV Blue Video Signal O 4 Reserved Reserved 5 GND Ground 6 GND Ground 7 GND Ground 8 GND Ground 9 +5V Power Supply 10 GND Ground 11 Reserved Reserved 12 SDA Serial Data Signal I/O 13 HSYNC Horizontal Sync Signal O 14
AC Power Cord and Connectors The AC input plug of the power cord must be compatible with the various international AC power outlets and the cord must meet the standards for the country/region in which it is used. All cords must meet the following specifications: Wire size: Minimum 0.75 mm2 Current rating: Minimum 2.5 amperes Certification agencies China: CQC U.S. and Canada: UL listed and CSA certified No.
USA United Kingdom UL approved BS approved Australia Europe AS approved Approved by the appropriate agency Canada China CSA approved CCC approved Information for Wireless Devices Wireless Technology Interoperability The Wireless LAN is compatible with other LAN systems Direct Sequence Spread Spectrum (DSSS) /Orthogonal Frequency Division Multiplexing (OFDM) radio technology, and is compliant to: The IEEE 802.
and Wireless LAN devices simultaneously, you might occasionally experience a less than optimal network performance or even lose your network connection. If you experience any such problem, immediately turn off either one of your Bluetooth or Wireless LAN. If you have any questions about using Wireless LAN or Bluetooth Module, visit http://www.pc.support.global.toshiba.com In Europe, visit http://www.toshiba-europe.com/computers/tnt/bluetooth.
Turn off all wireless functionalities when near a person who might have a cardiac pacemaker implant or other medical electric device. Radio waves might affect pacemaker or medical device operation, possibly resulting in serious injury. Follow the instruction for your medical device when using any wireless functionality. Always turn off wireless functionality if the computer is near automatic control equipment or appliances such as automatic doors or fire detectors.
Radio Frequency Band 5 GHz (5150-5850 MHz) (Revision a and n) Band 2.4 GHz (2400-2483.5 MHz) (Revision b/g and n) The range of the wireless signal is related to the transmit rate of the wireless communication. Communications at lower transmit range might travel larger distances. The range of your wireless devices can be affected when the antennas are placed near metal surfaces and solid high-density materials.
Radio links You can easily establish links between two or more devices, with these links being maintained even if the devices are not within a line-of-sight of each other. Bluetooth Stack for Windows by TOSHIBA Please note that this software is specifically designed for the following operating systems: Windows 7 Information regarding the use of this software with these operating systems is listed below, with further details being contained with the electronic help files supplied with the software.
Europe Restrictions for Use of 2400.0-2483.5MHz Frequencies in Europe France: Outdoor use limited to 10mW e.i.r.p. within the band 2454-2483.5MHz Military Radiolocation use.Refarming of the 2.4GHz band has been ongoing in recent years to allow current relaxed regulation Full implementation planned 2012. Italy: - For private use, a general authorization is required if WAS/ RLAN’s are used outside own premises. For public use, a general authorization is required.
Russian Federation: Limited e.i.r.p 100mW. Permitted to use only for indoor applications, closed industrial and warehouse areas, and on board aircraft. 1. 2. Permitted to use for local networks of aircraft crew service communications on board aircraft in area of the airport and at all stages of flight. Permitted to use for public wireless access local networks on board aircraft during a flight at the altitude not less than 3000m.
check the current channel of operation. If operation is occurring outside of the allowable frequencies for outdoor use, as listed above, the user must contact the applicable national spectrum regulator to request a license for outdoor operation. Canada - Industry Canada (IC) This device complies with RSS-210 of the Industry Canada Rules.
Canada limits for the general population; consult Safety Code 6, obtainable from Health Canada’s website www.hc-sc.gc.ca Caution: Exposure to Radio Frequency Radiation The radiated output power of the Wireless device is far below the FCC radio frequency exposure limits. Nevertheless, the Wireless device shall be used in such a manner that the potential for human contact during normal operation is minimized.
Australia and New Zealand regulatory compliance This equipment incorporates a radio transmitting device, in normal use a separation distance of 20cm will ensure radio frequency exposure levels complies with the Australian and New Zealand Standards. Using this equipment in Japan In Japan, the frequency bandwidth of 2,400MHz to 2,483.
(1) (2) (3) 1 (4) 1. 2. 3. 4. 2.4: This equipment uses a frequency of 2.4 GHz. FH: This equipment uses FH-SS modulation. 1: The interference range of this equipment is less than 10m. : This equipment uses a frequency bandwidth from 2,400 MHz to 2,483.5 MHz. It is impossible to avoid the band of mobile object identification systems. 4. About the JEITA 5GHz Wireless LAN supports W52/W53/W56 Channel.
Radio approvals for wireless devices This equipment is approved to the radio standard by the countries/regions in the following table. If you use this equipment in the countries/regions which are not listed in the following table, contact TOSHIBA Support.
2. 3. On the BIOS setup utility screen, change AMT Setup Prompt to Enabled. Press the F10 key, and press Y key to save the settings. When the computer restarts, the message “Press < Ctrl - P > to enter Intel(R) ME Setup” appears. Press CTRL + P to enter the MEBx Setup. To disable the AMT function, do the following: 1. 2. Select MEBx Login, and enter the default password “admin” in the password field. Enter a new password.
7. 8. Select MEBx Exit, and press Y key. When the computer restarts, go to BIOS setup utility. 9. On the BIOS setup utility screen, change AMT Setup Prompt to Disabled. Press the F10 key to save the settings, and press the Y key. When using the computer with the AC adaptor connected and the AMT function set to enabled, power might still be supplied to the system memory even when the computer power is turned off, or the computer is in Sleep Mode or Hibernation Mode.
Legal Footnotes Non-applicable Icons Certain computer chassis are designed to accommodate all possible configurations for an entire product series. Therefore, be aware that your selected model might not have all the features and specifications corresponding to all of the icons or switches shown on the computer chassis. CPU Central Processing Unit (CPU) Performance Legal Footnotes.
64-bit Operating System 64-bit CPU, Chipset and BIOS (Basic Input/Output System) 64-bit Device drivers 64-bit applications Certain 32-bit device drivers and/or applications might not be compatible with a 64-bit CPU/operating system and therefore might not function properly. Memory (Main System) Part of the main system memory might be used by the graphics system for graphics performance and therefore reduce the amount of main system memory available for other computing activities.
Internal Storage Drive Capacity 1 Gigabyte (GB) means 109 = 1,000,000,000 bytes using powers of 10. The computer operating system, however, reports storage capacity using powers of 2 for the definition of 1 GB = 230 = 1,073,741,824 bytes, and therefore shows less storage capacity. Available storage capacity will also be less if the product includes one or more pre-installed operating systems, such as Microsoft Operating System and/or pre-installed software applications, or media content.
VCCI Class B Information (Japan Only) この装置は、クラスＢ情報技術装置です。この装置は、家庭環境で使 用することを目的としていますが、この装置がラジオやテレビジョン 受信機に近接して使用されると、受信障害を引き起こすことがあります。 取扱説明書に従って正しい取り扱いをしてください。 ＶＣＣＩ－Ｂ OpenSSL Toolkit License Issues LICENSE ISSUES ============== The OpenSSL toolkit stays under a dual license, i.e. both the conditions of the OpenSSL License and the original SSLeay license apply to the toolkit. See below for the actual license texts. Actually both licenses are BSD-style Open Source licenses.
6. Redistributions of any form whatsoever must retain the following acknowledgment: "This product includes software developed by the OpenSSL Project for use in the OpenSSL Toolkit" ( http://www.openssl.org/ ) THIS SOFTWARE IS PROVIDED BY THE OpenSSL PROJECT ``AS IS AND ANY EXPRESSED OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED.
Redistribution and use in source and binary forms, with or without modification, are permitted provided that the following conditions are met: 1. 2. 3. Redistributions of source code must retain the copyright notice, this list of conditions and the following disclaimer. Redistributions in binary form must reproduce the above copyright notice, this list of conditions and the following disclaimer in the documentation and/or other materials provided with the distribution.
Introduction ============ The FreeType Project is distributed in several archive packages; some of them may contain, in addition to the FreeType font engine, various tools and contributions which rely on, or relate to, the FreeType Project. This license applies to all files found in such packages, and which do not fall under their own explicit license. The license affects thus the FreeType font engine, the test programs, documentation and makefiles, at the very least.
`You` refers to the licensee, or person using the project, where `using` is a generic term including compiling the project`s source code as well as linking it to form a `program` or `executable`. This program is referred to as `a program using the FreeType engine`. This license applies to all files distributed in the original FreeType Project, including all source code, binaries and documentation, unless otherwise stated in the file in its original, unmodified form as distributed in the original archive.
Neither the FreeType authors and contributors nor you shall use the name of the other for commercial, advertising, or promotional purposes without specific prior written permission. We suggest, but do not require, that you use one or more of the following phrases to refer to this software in your documentation or advertising materials: `FreeType Project`, `FreeType Engine`, `FreeType library`, or `FreeType Distribution`. As you have not signed this license, you are not required to accept it.
Index A Touch Pad 6-8 AC adaptor additional 4-29 connecting 2-3 DC IN 19V jack 3-3, 3-15 E Equipment checklist 2-1 External monitor problems 6-12 B Battery extending life 4-15 monitoring capacity 4-14 save mode 5-4 types 4-12 G Graphics Processing Unit 3-21 H Bluetooth Bluetooth Stack for Windows by Toshiba 5-2 C HW Setup accessing 5-10 window 5-10 K Cleaning the computer 1-11 Keyboard Function keys F1...
Memory card care 4-21 Power 6-4 Real Time Clock 6-6 Sound system 6-11 TOSHIBA support 6-13 Touch Pad 6-8 USB device 6-9 USB mouse 6-9 memory media card inserting 4-22 removing 4-22 Memory media slot 4-19 Moving the computer 1-11 R P Recovery Media 5-16 Password power on 5-4 Starting the computer by password 5-9 Supervisor 5-9 user 5-8 Pointing Device Touch Pad 3-10, 3-19 Recovery Partition 5-17 Restarting the computer 2-8 S SD/SDHC/SDXC Card formatting 4-21 note 4-20 Security lock 4-29 Power conditi
T TOSHIBA HDD/SSD Alert Utility 5-2 TOSHIBA PC Diagnostic Tool 5-1 Touch Pad 3-10, 3-19, 4-1, 6-8 Touch Screen 4-1 U USB device problems 6-9 V Video mode 4-32 Video RAM 3-21 W Web Camera 3-9, 3-18 Wireless communication 7-5 User's Manual Index-3
