Manual

Calling Service Personnel
Check the following guide for the possible cause of a problem before contacting service.
Symptom Cause Correction Page
No power. • The power plug is disconnected. • Connect the power plug securely into the 12,13
wall outlet.
The DVD video player turned off • The automatic power off function turned the • Press the PLAY button.
by itself, unit off. 17
No picture or abnormal colour • The TV is not set to receive DVD signal • Select the appropriate video input mode on
(pinkish, greenish, etc.), output, the TV so the picture from the DVD video 12,16
player appears on the TV screen.
• The video cable is not connected securely. • Connect the video cable securely into the 12,13
appropriate jacks.
• Mismatch setting between TV and this unit. • Select the correct Video Output setting. 35
• Wrong connection. • Checkthe connection. 12,13
• PROGRESSIVE button pressed on a TV • Toggle PROGRESSIVE button to turn off
equipped with component video input jacks progressive mode. 13
but does not support progressive scan.
No sound. • The equipment connected with the audio • Select the correct input mode of the audio
cable is not set to receive DVD signal output, receiver so you can listen to the sound from 12,16
the DVD video player.
• The audio cable is not connected securely. • Connect the audio cable securely into the 12-14
appropriate jacks.
• The audio receiver or %/is turned off. • Turn on the equipment connected with the 16
audio cable.
• The setting of output sound format is • Select the proper audio setting.
incorrect. 26,32,36
The playback picture has • The disc is dirty. 5
occasional distortion. • it is in fast forward or fast reverse playback.
Brightness is unstable or noises • The effect of copy protection.
are present in the playback 12
pictures.
The DVD video player does not 16
start playback.
6
16
16
5
32,36
Playback does not follow the
course of the disc's program.
Buttons do not work.
• No disc is inserted.
• An unplayable disc is inserted.
• The disc is placed upside down.
• The disc is not placed within the guide.
• The disc is dirty.
• The parental lock function is set.
• it is in the mode of repeat playback, memory
playback, etc.
• Power supply fluctuations or other
abnormalities such as static electricity may
interrupt correct operations.
• Eject the disc and clean it.
• Sometimes a small amount of picture
distortion may appear. This is not a
malfunction.
• Connect the DVD video player directly to the
TV. Avoid connecting the DVD video player
to a VCR or%//VCR combination.
• Insert a disc.
• Insert a playable disc. (Check the disc type
and color system.)
• Place the disc with the playback side down.
• Place the disc correctly inside the guide on
the disc tray.
• Clean the disc.
• Cancel the parental lock function or change
the parental lock level.
• These operations may prevent a proper
progress of the contents.
• Press and hold the ON/STANDBY button on
the front panel for more than about 3
seconds. The DVD video player turns off.
Press the button again toturn it on. if the
buttons still do not work, disconnect the
power plug and insert itinto the wall outlet
again.
• Point the remote control at the remote
sensor of the DVD video player.
• Operate the remote control within about 7 m.
The remote control does not • The remote control is not pointed atthe
work properly, remote sensor of the DVD video player. 10
• The remote control is too far from the DVD
video player. 10
• The batteries in the remote control are • Replace the batteries with new ones.
exhausted. 10
The logo and playing picture of DVD • Adjust sharpness too small or too large. • Adjust Brightness or sharpness to a certain level
player become poor. 24
The DVD player tray does not open • Tray Lock mode has been enable. • Disable the Tray Lock function 32
40
p2q 7*3990SU.pmd 40 30/9/2005, 10:31 AM