TOSHIBA AMERICA INFORMATION SYSTEMS STORAGE DEVICE DIVISION IRVINE, CALIFORNIA SD-M1712 DVD-ROM DRIVE USER MANUAL
CONTENTS Introduction..............................................................................1 Setup ........................................................................................3 Using the DVD-ROM Drive ......................................................6 Troubleshooting.......................................................................8 Specifications ..........................................................................9 Drive Connectors........................................
INTRODUCTION – SD-M1712 DVD-ROM Drive General Features Tray Loading Mechanism 3-way Disc Eject (eject button, software, emergency eject hole) Average Random Access Time CD-ROM DVD DVD-RAM 85ms 95ms 170ms DAE (Digital Audio Extraction) Audio Capability MPC3 Compatibility Multi-Read Capability Regionalization (RPC2 compliance) (DVD) ATAPI BUS Interface Drive Speed DVD CD DVD-RAM 16X Single Layer 10X Dual Layer 48X 2X (ver 1.0) 2X (ver 2.
CD • • • • • • • • • • • CD-DA CD+(E)G CD-MIDI CD-TEXT CD-ROM CD-ROM-XA CD-I Bridge (Photo-CD, Video CD) CD-I Multi-session (Photo-CD, CD Extra, CD-RW, CD-R) CD-R (Read) CD-RW (Read) Front Panel Figure 1.SD-M1712 DVD-ROM Drive Front Panel Loading Tray Load disc using tray. Busy Indicator When you install a disc into the DVD-ROM drive, the BUSY light flashes slowly as it attempts to locate the disc. One of the following will occur: • BUSY light goes out.
SETUP – SD-M1712 DVD-ROM The following steps must be performed to properly install your drive: • • • • • Set Drive Jumper Settings Connect Audio Cable (optional) Attach IDE BUS Cable Attach Power Cable Mount Drive Jumper Settings The mode select jumpers are 6 straight angle pins located on the rear of the DVD-ROM drive.
Placing DVD-ROM Drive inside your Computer Now that you have set the jumpers, you are ready to install your DVD-ROM drive inside your computer. Important Note: Disconnect power from your computer system before beginning installation. Remove computer cover and faceplate if required. Refer to your computer systems manual for removal information. If the DVD-ROM drive is replacing a CD-ROM or DVD-ROM, remove drive presently installed in your system.
Audio Cable (optional) - If you have a sound card and speakers, and would like to play audio CDs on your computer, you will need to install a CD/DVD audio cable. Toshiba's DVD-ROM drives use a standard 4-pin audio cable that can be purchased from most local computer suppliers. The sound cable connects to your sound card at one end and the other end connects to the digital audio connector at the left rear of the DVD-ROM drive (see DVD-ROM drive Back Panel photo for location).
USING THE DVD DVD-ROM Drive – SD-M1712 Drive Operation Inserting a Disc - Horizontally To insert a disc into a drive that is mounted horizontally, perform the following steps: Figure 1.Inserting Disc 1. Open the drive's Loading tray by pressing the Eject Button. 2. Place disc into drive's Loading tray 3. Press Eject button again or gently push on the open disc tray. Tray will automatically close.
Usage Guidelines • • • • • Keep the disc tray closed when not using the DVD-ROM Drive. Do not press down on the disc tray when opening or closing it. Do not place objects on the disc tray. Never use a damaged, broken, or deformed disc. Do not press the Open/Close button while the drive is playing a DVD movie or accessing a disc. To stop a DVD movie, click Stop button in the DVD player application program. NOTE: High-speed drives spin the disc at a high rotational speed.
TROUBLESHOOTING – SD-M1712 Solution Problem Disc tray cannot be opened • • Check that there is power to drive. Use Emergency Eject instructions to open tray. Drive is not recognized by system • Is the drive connected properly? Are all cables plugged in properly (e.g. Power Cable, Interface Cable and Audio Cables).
SPECIFICATIONS –SD-M1712 General Interface ATAPI Compatible DVD-ROM Standards DVD DVD-ROM (DVD-5, DVD-9, DVD-10, DVD-18) DVD-R, DVD-RW, DVD-RAM CD CD-DA CD-ROM CD-I Bridge (Photo-CD, Video CD) Multi-session (Photo-CD, CD Extra, CD-RW, CD-R) CD-MINI CD-TEXT CD+(E)G CD-ROM-XA CD-I CD-R (Read) CD-RW (Read) Storage Capacities DVD 4.377GB (DVD-5) 7.959GB (DVD-9) 8.754GB (DVD-10) 15.917GB (DVD-18) 3.679GB (DVD-R, Ver. 1.0) 4.377GB (DVD-R, Ver. 2.0) 2.324GB (DVD-RAM, Ver 1.0) 4.377GB (DVD-RAM, Ver 2.
Performance Rotational Speed DVD-ROM (6.0X - 16X) single layer (4.1X - 10X) dual layer DVD-R (Ver 2.0), DVD-RW (2 - 4.8X) DVD-R (Ver 1.0) (2 - 4.8X) DVD-RAM (Ver 1.0) (2X) DVD-RAM (Ver 2.1) (1X) DVD-Video CSS-disc (2 - 4.8X) CD-ROM, CD-R/RW(20.7 - 48X) CD-DA Transfer (14 - 32X) CD-DA/Video CD (4X - 7.8X) Data Transfer Rate DVD (Single) DVD (Dual) DVD-Video DVD-R, DVD-RW DVD-RAM ( Ver 1.0) DVD-RAM (Ver 2.
Spin-up Time DVD DVD-RAM (Ver 2.1) DVD-RAM (Ver 1.0) CD 1.5s Typ 1.5s Typ 1.9s Typ 1.4s Typ Data Buffer 192Kbytes Reliability MTBF Power ON Hours ON/OFF Cycles Number of Access Operating Duty Cycle MTTR Audio Number of Channels Frequency Response Distortion Output Levels Headphone Analog Line Out Digital Line Out 100,000 hours 5,436 hours/year 313 cycles/yea 600,000 accesses/year 20% of Power ON time (Reading/Seeking) 0.5 hours 2 20Hz to 20,000 Hz -80 dB (at 1kHz JIS A-weighted) 1.0V (rms Typ) 0.
Power DC Voltage and Current Requirements 5V 5%, 12V 5% +5V Sleep Standby Idle Random Access (average) 200mA 240mA 410mA (DVD) 430mA (CD) 660mA (DVD) 600mA (CD) +12V 0mA 0mA 50mA (DVD) 50mA (CD) 730mA (DVD) 830mA (CD) Physical Height Width Depth Weight 5.75" (146mm) 1.6" (41.5mm) 7.6" (193mm) 2.18lbs (.
DRIVE CONNECTORS –SD-M1712 Figure 1.SD-M1712 DVD-ROM Drive Rear Panel - Connectors Power Connector Power is supplied to your DVD-ROM drive by the connection with your computer's +5V/+12V power cable to the power socket at the back of drive. One side of the plug has chamfered edges, so the power connector fits only one way CAUTION: Severe damage to the Drive circuits may occur if power cable is plugged in upside-down with power ON.
Table 1.Interface Pin Assignments INTERFACE PIN ASSIGNMENT PIN NO. 1 2 3 4 5 I/O I I/O I/O I/O SIGNAL NAME Reset GND HD7 HD8 HD6 6 7 I/O I/O 8 9 10 11 12 13 14 15 16 17 18 19 20 14 HOST SIGNAL NAME I/O Host Data Bus BIT 7 Host Data Bus BIT 8 Host Data Bus BIT 6 PIN NO.
