User’s Manual Slim Port Replicator III
Slim Port Replicator III Safety Icons User’s Manual This manual contains safety instructions that must be observed to avoid potential hazards that could result in personal injuries, damage to your equipment, or loss of data.
Slim Port Replicator III n Never run a power cable/cord through a pinch point such as a door or window. n Never place a power cable/cord near a heat source. n Never use nails, staples or similar objects to fasten or attach cord in place. n Never attempt to disassemble or repair an AC adaptor. Doing any of the above may damage the cables, and/or result in a fire or electric shock, possibly resulting in serious injury.
Slim Port Replicator III Choking hazards n Never leave small parts such as covers, caps and screws within the reach of infants or small children. Swallowing a small part may cause choking and suffocation resulting in death or serious injury. If a part is swallowed, immediately take appropriate emergency action and consult a doctor. Avoid liquids, moisture and foreign objects n Never allow any liquids to spill into any part of your product, and never expose the product to rain, water, seawater or moisture.
Slim Port Replicator III Table of Contents Chapter 1 Introduction Equipment Checklist . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 Features. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 Quick Tour . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 Special Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Slim Port Replicator III Chapter 1 Introduction Thank you for your purchase of the TOSHIBA Slim Port Replicator III. This manual tells you how to set up and begin using your Slim Port Replicator III and provides tips on care and troubleshooting. Equipment Checklist Carefully unpack your Slim Port Replicator III. Save the box and packing materials for future use.
Slim Port Replicator III Quick Tour This section identifies the various components of the Slim Port Replicator III. Front View Figure 1-1 shows the Slim Port Replicator III’s front side. Power Switch Computer Connector Docking LED Eject Button Guide Pin Hooks Guide Pin Figure 1-1 The front side of the Slim Port Replicator III Power Switch NOTE NOTE User’s Manual Turns the docked computer’s power on and off.
Slim Port Replicator III Right View Figure 1-2 shows the Slim Port Replicator III’s right side. Eject Lever Figure 1-2 The right side of the Slim Port Replicator III Eject Lever NOTE Disengages the computer from the Slim Port Replicator III. Refer to chapter 2 to learn how to disconnect your computer from the Slim Port Replicator III properly. When the Computer Lock Switch is in the lock position, the eject lever cannot be moved. Back View Figure 1-3 shows the Slim Port Replicator III’s back side.
Slim Port Replicator III LAN Jack NOTE Connection point for a network cable. Supports: n Ethernet (10 megabits per second, 10BASE-T) n Fast Ethernet (100 megabits per second, 100BASE-T) n Gigabit Ethernet (1000 megabits per second, 1000BASE-T) Gigabit Ethernet support is only available if your computer model also supports it. Universal Serial Connection points for USB 2.0 or 1.1 devices. Six Bus (USB 2.0) Ports USB ports are provided on the back of the Slim Port Replicator III.
Slim Port Replicator III Left View Refer to Figure 1-4 for the location of items on the Slim Port Replicator III’s left side. Computer Lock Switch Security Lock Slot Figure 1-4 The left side of the Slim Port Replicator III Security Lock Slot Attachment point for an optional security cable (not included) used to deter theft. Computer Lock Switch In the locked position, helps prevent disconnection of the computer from the Slim Port Replicator III.
Slim Port Replicator III Chapter 2 Setting Up and Using the Slim Port Replicator III This chapter explains how to set up the Slim Port Replicator III and dock/ undock your computer. NOTE When the Slim Port Replicator III is connected to the computer, do not use the ports of the computer. If you use the ports on both the computer and the Slim Port Replicator III simultaneously, it may harm the computer and/ or data contained in it.
Slim Port Replicator III To supply AC power to the computer, connect the AC adaptor according to the steps below: WARNING The supplied power cord conforms to safety rules and regulations in the region where the product was purchased. Do not use the AC adaptor that was included with your computer. Always use the Toshiba AC adaptor that was provided with this product or use Toshiba recommended alternate adaptors to avoid any risk of fire and/or other damage to the computer and/or port replicator.
Slim Port Replicator III NOTE When the Slim Port Replicator III is connected to the computer successfully, the docking LED will glow blue if the computer is turned on. The Slim Port Replicator III is now ready for use. Disconnecting the Slim Port Replicator III To disconnect the Slim Port Replicator III, follow the steps below and save all your work first. 1. Slide the Computer lock switch to the unlock position: Figure 2-4 Sliding the Computer lock switch 2.
Slim Port Replicator III 3. To disconnect the computer, pull the eject lever towards you while sliding the computer backwards. Figure 2-6 Disconnecting a notebook from the Slim Port Replicator III 4. Lift off the computer. Figure 2-7 Lifting the Computer CAUTION Do not lift up the computer without sliding the computer backwards, otherwise the Slim Port Replicator III’s hooks may be damaged.
Slim Port Replicator III Follow these steps to secure your computer and the Slim Port Replicator III: 1. Attach your security cable (purchased separately) to a desk or other large object, following the instructions included with your security cable. 2. Set the computer lock switch on the Slim Port Replicator III to the locked position. 3. Insert the lock end of the security cable into the Slim Port Replicator III’s security lock slot. 4. Turn the key or set the combination on the end of the security cable.
Slim Port Replicator III 1. Plug one end of the network cable into the Slim Port Replicator III’s LAN jack. Gently push the cable connector in until you hear the latch click into place Figure 2-10 Connecting the LAN cable 2. Plug the other end of the cable into a LAN hub connector. NOTE When the computer is exchanging data with the LAN, the LAN Active indicator glows orange. When the computer is connected to a LAN hub but is not exchanging data, the Link indicator glows green.
Slim Port Replicator III Configuring audio playback ports (Line out) in Windows Vista® 1. Right-click the speaker icon in the Notification Area of your Windows® desktop. Windows Vista® NOTE If the speaker icon is not visible in the Notification Area, access the audio configuration utility through the Start menu as follows: Click Start, Control Panel, Hardware and Sound, and then Sound. 2. Select Playback Devices from the menu. 3.
Slim Port Replicator III Configuring audio recording ports (Microphone) in Windows Vista® 1. Right-click the speaker icon in the Notification Area of your Windows® desktop. Windows Vista® NOTE If the speaker icon is not visible in the Notification Area, access the audio configuration utility through the Start menu as follows: Click Start, Control Panel, Hardware and Sound, and then Sound. 2. Select Recording Devices from the menu. 3.
Slim Port Replicator III Chapter 3 Troubleshooting This chapter provides tips to correct problems, should any occur. It also describes how to contact TOSHIBA should you encounter problems that you cannot resolve. Before you call Toshiba, please refer to the general troubleshooting advice in this manual and in your computer’s user manual. You may also want to consult with your system administrator or company technical support staff.
Slim Port Replicator III Problem Solution(s) Docked computer enters Resume mode and shuts down If the computer’s internal temperature becomes too high, the computer will automatically enter Resume mode and shut down. Leave the computer off until its interior reaches room temperature. If the computer has reached room temperature and still does not start, or if it starts but shuts down quickly, contact Toshiba support.
Slim Port Replicator III USB issues NOTE This section refers to the TOSHIBA Hardware Setup diagnostic utility. To learn how to access the TOSHIBA Hardware Setup utility, please refer to your computer user’s guide. Problem Solution(s) USB device does not work Check that the cable connection between the USB ports on the Slim Port Replicator III and the USB device is secure. Make sure the USB device drivers are properly installed.
Slim Port Replicator III Hardware issues Problem Solution(s) Cannot operate the computer lock switch The computer lock switch cannot be operated when a security cable is attached to the security lock slot. Remove the security cable from the slot and then move the computer lock switch. Cannot operate the Eject lever Remove the security cable from the security lock slot, if applicable, and set the computer lock switch to the unlocked position. Then operate the Eject lever again.
Slim Port Replicator III Problem Solution(s) There is no sound coming from the internal speakers of my docked computer, or from the headphones/headset connected directly to my docked computer Check that the Mute all/Mute checkboxes in Windows® are not selected. To locate these settings, double-click the speaker icon in your Windows® system tray/Notification Area. By default, the internal speakers and audio ports on the computer are disabled when the computer is docked in the port replicator.
Slim Port Replicator III FCC Information FCC notice “Declaration of Conformity Information” This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
Slim Port Replicator III Disclaimer Information in this document is subject to change without notice. The manufacturer does not make any representations or warranties (implied or otherwise) regarding the accuracy and completeness of this document and shall in no event be liable for any loss of profit or any commercial damage, including but not limited to special, incidental, consequential, or other damage. January 2009, Rev1.
Slim Port Replicator III n Medical environment: The compliance to the Medical Product Directive has not been verified by Toshiba, therefore this product cannot be used as a medical product without further verification. The use in usual office environments e.g. in hospitals should be no problem if there is no restriction by the responsible administration. n Automotive environment: Please search the owner instructions of the related vehicle for advices regarding the use of this product (category).
Slim Port Replicator III Appendix A Specifications This appendix summarizes the Slim Port Replicator III’s technical specifications. Physical Dimensions Weight about 420g (14.8 ounces) Size Width: 283mm (11.2") Height: 25mm (1") Depth: 90mm (3.
Slim Port Replicator III Appendix B AC Power Cord and Connectors The power cord’s AC input plug must be compatible with the various international AC power outlets and the cord must meet the standards for the country/region in which it is used. All cords must meet the following specifications: Length: Minimum 1.7 meters Wire size: Minimum 0.75 mm2 Current rating: Minimum 2.5 amperes Voltage rating: 100 to 240 VAC (depending on country/region’s power standards) Certification agencies U.S.
Slim Port Replicator III For the United States and Canada, two pin plug configuration must be a 2-15P (250V) or 1-15P (125V) and three pin plug configuration must be 6-15P (250V) or 5-15P (125V) as designated in the U.S. National Electrical code handbook and the Canadian Electrical Code Part II. The following illustrations show the plug shapes for the U.S.A. and Canada, the United Kingdom, Australia and Europe.
Slim Port Replicator III Index C T CAT5 CAT5 CAT5E cables 15 configuring audio ports 16 playback ports (Line out) 17 recording ports (Line in) 18 connecting LAN cable 15 TOSHIBA support 23 Troubleshooting AC power 19 troubleshooting power 19 D Windows Vista® (Line in) 18 (Line out) 17 Windows® XP (Line in) 18 (Line out) 17 DC-IN 15V 9 E Eject 7 Eject Button 7 Eject button 7 Eject LED 7 Eject lever 8 Eject switch 7 Equipment checklist 6 W P port Line out (headphones, speakers) 8 Port Replicator con
GMH300063E20 *GMH300063E20*
