SoundStrip Sound Bar Speaker System User’s Guide: SBX5065KU ® If you need assistance: Toshiba’s Support Web site : support.toshiba.com For more information see “Troubleshooting” on page 18 in this guide. Owner’s Record The model number and serial number are on the back and underside of your SoundStrip®. Record these numbers in the spaces below. Refer to these numbers whenever you communicate with your Toshiba dealer about this SoundStrip®.
Contents Introduction .......................................................................................... 6 Safety icons used in this manual............................................................ 6 SoundStrip® speaker system controls ................................................... 7 Remote control ................................................................................... 10 SoundStrip® speaker system placement .............................................
Safety Precautions The lightning flash with an arrowhead symbol, within the equilateral triangle, is intended to alert the user to the presence of uninsulated “dangerous voltage” within the product’s enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons. The exclamation point within the equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in this User’s Guide.
Additional Safety Instructions 18. If the apparatus should emit smoke or an unusual odor, immediately disconnect the power cord from the wall outlet. Wait until the smoke or smell stops, then ask your dealer for a check and repair. Neglecting to do so may cause fire. 19. During thunderstorms, do not touch the connecting cables or the apparatus. 20. Warning: To prevent spread of fire, keep candles or other open flames away from this product at all times. 21.
Precautions On Safety Do not handle the AC power cord with wet hands. When connecting or disconnecting the AC power cord, grip the plug and not the cord itself. Pulling the cord may damage it and create a hazard. When you are not going to use the unit for a long period of time, disconnect the AC power cord. On Recycling This unit’s packaging materials are recyclable and can be reused. Please dispose of any materials in accordance with your local recycling regulations.
Introduction Safety icons This guide contains safety instructions that must be observed to avoid potential hazards that could result in personal injuries, damage to your equipment, or loss of data. These safety cautions have been classified according to the seriousness of the risk, and icons highlight these instructions as follows: Indicates an imminently hazardous situation which, if not avoided, will result in death or serious injury.
SoundStrip® front panel SoundStrip® speaker system controls (Sample Illustration) Front & Top panel controls Item: 1 2 3 Description: VOLUME button BASS VOLUME button MODE button Function: Press to adjust the volume level. Press to adjust the bass volume level. Press to select the surround mode from Stereo/SRS TruSurround HD/SRS TruBass. 4 INPUT button Press to switch between HDMI 1/2 (HDMI® IN), ARC (HDMI® ARC) , BT (Bluetooth ®), OPT 1/2 (OPTICAL IN), AUX (AUX IN) or LINE-IN.
SoundStrip® back panel 9 13 10 11 14 15 (Sample Illustration) Back panel connections Item: Description: Functions: 9 OPTICAL IN jack (1) & (2) Connects the optical audio input to another device, see “Connecting to an Audio System” on page 14. 10 AUX IN jack (L / R) Connects other AV devices through the AUX IN jack, see “Connect audio through an analog audio cable” section on page 14.
Subwoofer (Sample Illustration) Subwoofer connections Item: Description: Functions: 15 Bass port 16 Subwoofer Speaker 17 WIRELESS LINK button Press to pair the subwoofer with the SoundStrip®. WIRELESS LINK indicator The indicator is red when the wireless link is activated. 18 POWER switch Switch to turn ON/OFF the subwoofer. 19 Power cord Connects to a standard AC outlet to supply power to the subwoofer.
Remote control 1 7 2 8 3 Item: Description: Operation: 1 MUTE Press to turn the sound off. Press again to cancel. 2 Press to turn the HDMI® CEC on/off. 3 4 9 5 10 Press to adjust the volume level. Press to go to the last track or advance to the next track in Bluetooth® mode. PLAY/PAUSE Press to play/pause the track in Bluetooth® mode. 4 EQ Press to select the sound setting. (Flat/Rock/Pop/Jazz/Classic/Movie) When in stereo mode, use EQ to select your settings.
Installing the batteries Install the batteries (AAAx2), matching the polarity indicated inside the battery compartment of the remote control. 1 Open the battery cover. (Sample Illustration) Remote control - Opening the battery cover 2 Insert batteries. Make sure to match the polarity marks (+ / –) on the batteries to the marks indicated in the battery compartment. (Sample Illustration) Remote control - inserting the batteries 3 Replace the battery cover. Never throw batteries in a fire.
SoundStrip® speaker system placement The SoundStrip® can be placed freestanding on a table or mounted on a wall. For the best surround sound experience, place your subwoofer as shown below. Place the subwoofer at least 11.8” (300mm) away from the TV. TV 300mm SoundStrip Sound Bar ® Subwoofer (Sample Illustration) Subwoofer placement Placing the unit on a wall The SoundStrip® requires additional mounting hardware that must be purchased separately. 1.
SoundStrip® speaker system connections Connecting to a TV using an HDMI® (ARC) cable. This feature enables the audio signal of the TV to be sent to the SoundStrip® via the HDMI® cable. The HDMI® cable is not included and must be purchased separately. Be sure that the connected TV has an HDMI® (ARC) compatible terminal. To connect the HDMI® ARC cable: 1. Connect an HDMI® cable from the HDMI® output jack on the SoundStrip® to the HDMI® input jack on the TV. 2.
Connecting to an Audio System. You can connect your SoundStrip® to an audio system to play audio from other devices. Connect audio through a digital optical cable 1. You can connect a optical cable from the OPTICAL input jack on the SoundStrip® to the OPTICAL output jack on the other device. 2. Press the INPUT button to select the OPTICAL mode and the display will show “OPT-1” or “OPT-2”. When your SoundStrip® and TV are connected through HDMI® (ARC), an audio connection is not required.
2. Connect a 3.5mm cable (not included) from the LINE input jack on the SoundStrip® to the other device. 3. Press the INPUT button to select the LINE IN mode and the display will show “LINE-IN”. not supplied Portable music player or other Audio Devices (Sample Illustration) 3.5mm connection to audio device Connecting to a switching power supply (AC Adapter). Using a switching power supply (AC Adapter) other than the one supplied with the unit may damage the unit.
Subwoofer wireless connection In order to use the subwoofer, you must pair it with the SoundStrip®. 1. Connect the power cord to a wall outlet. 2. Turn on the SoundStrip®. 3. Turn the ON/OFF switch on the back of subwoofer to the “on” position. 4. The SoundStrip® and the subwoofer will automatically pair up. The pairing indicator located in upper right corner of the rear panel will appear red when the wireless link is activated.
Bluetooth® connection by NFC NFC (Near Field Communication) is a technology enabling short-range wireless communication between various devices, such as mobile phones and IC tags. By just touching the SoundStrip® where the “N-mark” is located with an NFC compatible device, the SoundStrip® is turned on automatically and then paired and connected with the various devices, such as mobile phones. To locate the “N-mark” on the unit, please see page 7. 1. Start and turn on the NFC function on the device.
Troubleshooting Problem: Solution: The unit does not switch on. Make sure it is plugged into a AC power outlet and the outlet is turned ON. Press the STANDBY/ON button located on the top of the SoundStrip®, and check to see if the STANDBY/ON indicator turns off. Turn the subwoofer power switch to ON. No sound from the SoundStrip® Press the VOL button of the SoundStrip®. Ensure the source you have selected is outputting audio.
Specifications These models comply with the specifications listed below. Designs and specifications are subject to change without notice. These models may not be compatible with features and/or specifications that may be added in the future. Main unit: Power requirements DC 27.5V Power output 75 watts (per channel at 4 ohms, 1 kHz/THD10%) Power consumption 27W Impedance 4 Dimensions (width x height x depth) 44.6” x 3” x 2.3” (1133 x 76 x 57mm) Weight 5.1 lbs (2.3kg) 3.
SBX5065KU_IB_R6.