TEC POS Terminal ST-60 SERIES Owner’s Manual
CE Compliance (for EU only) This product complies with the requirements of EMC and Low Voltage Directives including their amendments. WARNING This is a Class A product. In a domestic environment this product may cause radio interference in which case the user may be required to take adequate measures. Warnung Dies ist ein Klasse A Produkt. In einer örtlichen Umgebung kann dieses Gerät Funkstörungen verursachen. ATTENTION Ce produit est de classe A.
EO1-11099 Safety Summary Safety Summary Personal safety in handling or maintaining the equipment is extremely important. Warnings and Cautions necessary for safe handling are included in this manual. All warnings and cautions contained in this manual should be read and understood before handling or maintaining the equipment. Do not attempt to effect repairs or modifications to this equipment.
EO1-11099 Safety Summary Disconnect the plug. Connect a grounding wire. If foreign objects (metal fragments, water, liquids) enter the machines, first turn off the power switches and disconnect the power cord plugs from the outlet, and then contact your authorized TOSHIBA TEC representative for assistance. Continued use of the machine in that condition may cause fire or electric shock. Disconnect the plug. Ensure that the equipment is properly grounded. Extension cables should also be grounded.
EO1-12026 TABLE OF CONTENTS Page 1. INTRODUCTION .............................................................................. 1-1 1.1 APPLICABLE MODEL .............................................................................. 1-1 1.2 ACCESSORIES ....................................................................................... 1-1 2. SPECIFICATIONS ........................................................................... 2-1 2.1 2.2 2.3 2.4 2.5 GENERAL SPECIFICATIONS .......................
EO1-12026 1. INTRODUCTION 1.1 APPLICABLE MODEL 1. INTRODUCTION Thank you for choosing the TEC ST-60 Series POS Terminal. This POS Terminal contains all the high performance register functions necessary for a specialty store POS terminal and enables the user oriented system configuration.
EO1-12026 1. INTRODUCTION 1.2 ACCESSORIES 1.2 ACCESSORIES Confirm that all the following accessories are contained in the carton. If any accessories are missing or damaged, contact your TOSHIBA TEC service representative. 1 2 3 4 5 6 7 8 9 No.
EO1-12026 2. SPECIFICATION 2.1 GENERAL SPECIFICATIONS 2. SPECIFICATIONS 2.1 GENERAL SPECIFICATIONS (1) A and B models Item Supply voltage (Autosensing) Power consumption Operating temperature Relative humidity Dimensions Weight NOTE: Description AC 100V-127V +10% -10% 50/60 Hz AC 220V-240V +10% -10% 50/60 Hz AC 100V Input Standby: 72W Operation: 72W (When HS-520 Touch Scanner and LIUST-53 Display Unit are connected.
EO1-12026 2. SPECIFICATION 2.2 ENGINE SPECIFICATIONS 2.2 ENGINE SPECIFICATIONS (1) A and B models Model Item CPU BIOS ROM RAM Capacity Type Socket Secondary Cache Interface Customer's Display Touch Panel Method UPS Hard Disk Drive Floppy Disk Drive LAN interface PC Card MCR NV-RAM A B AMD K6 266MHz AMD K6-2 333MHz 512KB Flash ROM 8MB as standard on board, Max.72MB (8MB + 64MB DIMM) EDO 64bits, non-parity, without ECC, non-buffered, 60ns, 3.
EO1-12026 2. SPECIFICATION 2.3 OPERATOR’S DISPLAY SPECIFICATIONS 2.3 OPERATOR’S DISPLAY SPECIFICATIONS Item Display Type Display Size Number of Colors Display Area Dot Size Touch Panel Adjustment Mechanism Interface with LCD 2.4 2.4.1 CUSTOMER’S DISPLAY SPECIFICATIONS ANK 20 Characters x 2 Lines Dot Display (With 2 lines Dot Display model) Item Number of displayed characters Display Color Display Area, Character Size Type font Interface with ENGINE NOTE: 2.4.2 Description 12.
EO1-12026 2. SPECIFICATION 2.5 OPTIONS 2.
EO1-12026 3. APPEARANCE 3.1 FRONT/REAR VIEW 3. APPEARANCE CAUTION: Do not place any articles on the Display Panel of the ST-60. Doing so may damage the ST-60. Do not press the Reset Switch unnecessarily. Doing so may cause an error. 3.1 FRONT/REAR VIEW ■ FRONT VIEW 12.
EO1-12026 3. APPEARANCE 3.2 CONNECTORS PS-2 Connectors: USB Connectors: Power LED (Green): HDD LED (Yellow): FDD Connector: Reset Switch: Brightness Control: Speaker Volume Control: 3.2 Connector for the PS-2 type mouse (A mouse cannot be used when the touch panel is activated.) Connector for the PS-2 type keyboard (PKBST-50/51/51C or PC Keyboard) (When the MCR is installed, this connector can be used for the PC keyboard interface.
EO1-12026 4. INSTALLATION PROCEDURE 4.1 ENVIRONMENT FOR INSTALLATION 4. 4.1 INSTALLATION PROCEDURE ENVIRONMENT FOR INSTALLATION Since heat will be built up inside the unit during operation, ventilating slits are provided to send away internal air. When installing the terminal, be sure to allow a 30mm or more clearance on the left and right side of the terminal so as not to block the ventilating slits. 4.
EO1-12026 5. ADJUSTMENT 5.1 TILT ANGLE ADJUSTMENT 5. ADJUSTMENT Tilt angle and brightness of the operator’s display, and speaker volume can be adjusted. CAUTION: Do not adjust the display angle by holding the LCD panel. Doing so may damage the unit. Be sure to hold the LCD frame. 5.1 TILT ANGLE ADJUSTMENT The tilt angle of the operator’s display can be adjusted freely in a range of 0° to 90°.
EO1-12026 6. FLOPPY DISK AND FLOPPY DISK DRIVE (OPTION) 6.1 FLOPPY DISK WRITE PROTECTION 6. FLOPPY DISK AND FLOPPY DISK DRIVE (OPTION) WARNING! Before connecting and disconnecting the optional FDDST-60-1-QM FDD unit, be sure to turn the ST-60 power OFF. CAUTION: When handling a floppy disk, care should be taken as follows: • Do not place the floppy disk close to any magnetic product. • Do not use a damaged floppy disk. • Do not bend the floppy disk. • Keep the floppy disk away from water.
EO1-12026 6. FLOPPY DISK AND FLOPPY DISK DRIVE (OPTION) 6.2 LOADING/EJECTING THE FLOPPY DISK 6.2 6.2.1 LOADING/EJECTING THE FLOPPY DISK Loading the Floppy Disk Insert the floppy disk gently with the label side facing up until it clicks. When the floppy disk is correctly inserted, the eject button pops out. 6.2.2 Ejecting the Floppy Disk CAUTION: Do not press the eject button while the active LED is lit. Doing so may destroy the data in the floppy disk.
EO1-12026 7. MAGNETIC CARD READER (OPTION) 7.1 HOW TO READ MAGNETIC CARD 7. MAGNETIC CARD READER (OPTION) The MCRST-60-3/5-QM optional magnetic card reader can be installed on the right side of the ST-60. These card readers read track 1 and 2 (MCRST-60-3-QM) or track 1, 2 and 3 (MCRST-60-5-QM) magnetic cards which comply with ISO1. 7.1 HOW TO READ MAGNETIC CARD Insert the magnetic card into the upper portion of the magnetic card reader slot and move the card downward slowly.
EO1-12026 8. GENERAL MAINTENANCE 8.1 CLEANING 8. 8.1 GENERAL MAINTENANCE CLEANING WARNING! 1. Be sure to disconnect the power cord prior to performing any maintenance. 2. Do not pour water directly on or wipe the operator’s display with a soaked cloth, as this may cause fire, electric shock, or machine failure. CAUTION: 1. Never use an organic solvent like thinners or benzene for cleaning. Using such solvents may discolor the covers. 2. Do not use any sharp object to clean the operator’s display.
EO1-12026 9. TROUBLESHOOTING 9. TROUBLESHOOTING 9. TROUBLESHOOTING WARNING! If you cannot solve a problem with the following solutions, do not attempt to repair it by yourself. Turn the power off, unplug the POS Terminal, then contact your TOSHIBA TEC representative for assistance. Symptom The power does not turn on. • • • The operator’s display is hard to see.
Toshiba TEC Corporation
