NVR Network Video Recording Software User Manual Models Please carefully read these instructions before using this product Save this manual for future use 1 SWIP-32 SWIP-16 SWIP-8
ii
iii Surveillix™ NVR Server Software Manual (Version 4) Manual Edition 27177AJ – OCTOBER 2009 Printed in USA No part of this documentation may be reproduced in any means, electronic or mechanical, for any purpose, except as expressed in the Software License Agreement. Toshiba shall not be liable for technical or editorial errors or omissions contained herein. The information in this document is subject to change without notice.
iv
v Table of Contents PREFACE ...................................................................................................................................................................... 9 About This Guide....................................................................................................................................................... 9 Technician Notes................................................................................................................................
vi Connecting a Second Monitor ............................................................................................................................ 35 Volume ............................................................................................................................................................... 36 Hybrid Sensor Setup ..........................................................................................................................................
vii Printing an Image .................................................................................................................................................... 56 Daylight SAVIng Time ............................................................................................................................................. 56 Save to JPG or AVI .................................................................................................................................................
viii Configuring TCP/IP Settings ............................................................................................................................... 82 LDAP INTEGRATION.................................................................................................................................................. 83 Features ..................................................................................................................................................................
PREFACE ABOUT THIS GUIDE This manual is a setup and maintenance guide that can be used for reference when setting up the NVR and for troubleshooting when a problem occurs. Only authorized personnel should attempt to repair this unit. Toshiba reserves the right to make changes to the NVRs represented by this manual without notice.
INTRODUCTION PRODUCT DESCRIPTION Toshiba’s NVR Software is the next great step in surveillance. The NVR Software has been designed for use on non-proprietary hardware and existing IT infrastructures, making it a cost effective next generation surveillance package. The NVR Software allows users to connect up to 32 network cameras and/or network video encoders per server. The Surveillix NVR software comes pre-configured for fast and seamless integration with non-proprietary hardware.
NVR SOFTWARE REQUIREMENTS Recommended Workstation/Server for NVR Software Total Cameras / Video Input 8/16 32 Type & Number or Processors: Intel® Q8200 2.33GHz+ Core 2 Quad X Intel® Q9550 2.
NVR SOFTWARE SPECIFICATIONS Total Cameras / Video Input Recording Rate: 8 16 30 PPS per camera (depending on hardware configuration) PTZ Control Sample Image Size Averages: 32 YES Variable Depending on Network Camera and Network Camera Settings Password Control: User Defined Access Image Compression: Dependant on Camera, MJPEG, MPEG4, H.264 Motion Detection: Up to 15 Regions Per Ch.
GETTING STARTED This chapter includes the following information: • Software CD Contents
NVR CONTENTS Identify the following components to make sure everything has been properly included with your new NVR Software CD. If any of the following items are missing, contact your dealer to arrange a replacement. Included Component List: NVR Network Video Recording Software User Manual Please carefully read these instructionsbefore using this product. Savethis manual for future use.
NVR BASICS This chapter includes the following information: • Installing the NVR Software • Registering the NVR Software • Becoming familiar with the Display screen • Defining Screen Divisions
INSTALLING THE SOFTWARE Installing NERO® Burning Rom The NVR Software has been designed to work with Nero Burning Software Version 8. When installed, Nero will enable backup to the CD ROM directly within the NVR Software. Without Nero installed, video data may still be backed up but must be saved locally first and then copied to a CD using a separate application outside the NVR Software. CAUTION: NERO Burning Rom must be installed on the PC prior to installing the NVR Software.
Registering the NVR Software Have the following information available before registering. Software Serial Number: That product Serial Number is the unique number that Toshiba provided with the purchase software. System ID: The System ID is a unique code generated using the MAC address of the computer running the software. The following steps illustrate how to obtain a unique System ID. Locating the System ID 1. From the Display screen, click Setup. 2. Click Network Cameras. 3.
5. Verify the information. 6. Click Next if the information provided is correct. 7. Once validated, the user will be provided with the Unlock Code. 8. Print the page and save for later reference. Unlocking the Upgrade 1. Return to Setup > Network Cameras > License. 2. Enter the Unlock Code generated by the Surveillix Registration Site into the License Key box. 3. Click Register and confirm that the new License Key is listed in the Channel Connection License box. 4. Click OK.
DISPLAY SCREEN Each time the DVR starts, the program defaults to the Display screen. The following diagram outlines the buttons and features used on the Display screen. You should become familiar with these options as this is the screen that will be displayed the majority of the time.
CAMERA VIEW Recording Status Special Recording Type INSTANT Camera No. and Name Recording Status Indicator The camera status for each camera is displayed in the upper right corner on the Video Display Area. The following are the different states for each camera: Recording Displayed when the camera is currently being recorded to the DVR. Motion Detection Displayed when a camera (set up for motion detection) detects motion.
SCREEN DIVISION BUTTONS The Screen Division menu allows you to view cameras in groups such as two by two, three by three and four by four. The button options are shown below. 1st Four Cameras View – Displays cameras 1-4 in the Video Display Area. To return to a different Multi-Camera View, select a different Screen Division option from the Screen Division menu. 2nd Four Cameras View – Displays cameras 5-8 in the Video Display Area.
Custom Live View Divisions Customize your Live View screen by changing the order of the cameras. Each screen division can be individually customized but a camera can only be displayed once (once in 4 camera view, once in 9 camera view, etc). Both analog and IP video cameras can be moved. Create custom live view divisions: 1. On the Live View screen click Setup, and then click General. 2. Click Sequence Setting. 3.
SETUP OPTIONS This chapter includes the following information: • Setup Overview • Camera Setup • Motion • Schedule • Network • Information • Administrative
SETUP OVERVIEW The Setup options allow you to optimize your DVR by adjusting things like camera names, reboot schedules, recording schedules and more. It is extremely important that you setup your DVR correctly for several reasons. • Recording Schedules – By optimizing the recording schedule you can increase the amount of pertinent recorded video that is saved on the DVR and keep it longer.
CAMERA SETUP Define Camera Name Selected Camera Display Select Camera Selects the camera to be edited. Selected Camera Display Displays the live camera feed from the camera selected. Sensor Connection Specify which sensors are currently in use. Camera Name Specify a name for each camera.
NETWORK VIDEO Connected Devices Automatic Camera Finder Supported IP Camera Manufacturers ACTi Arecont Vision Axis Brans D-Link IQeye Lumenera Mobotix Panasonic Pixord Samsung Securgen Sony Stardot Toshiba VivoTek Connecting a Network Device Connecting Manually 1. From the Display screen, click Setup. 2. Click Network Video. 3. Click the Add/Remove Device tab. 4. Select your network device from the Device Type list. 5. Type a Device Name. 6.
Connecting with Camera Finder 1. From the Display screen, click Setup. 2. Click the Network Video tab. 3. Click the Add/Remove Device tab. 4. Click Find Cameras to automatically find all connected Network cameras. 5. Select the check box next to the desired camera. 6. Click Get Device. 7. Type the User ID and Password of the device. 8. Click Update. Assigning a Network Device to a Channel 1. From the Display screen, click Setup. 2. Click Network Video. 3.
Assigning Audio Channels to a Network Device 1. From the Live View screen, click Setup. 2. Click Network Video. 3. Click the Audio Setup tab. 4. Click an available audio channel on the Channel List. 5. Select a network device added previously. 6. To record the network audio select the Record Network Audio check box. The audio channel will be available on the search screen. 7. To access the audio channel from the Live View screen, select the Enable Network Video in Live View check box.
Camera Configuration The Camera Configuration tab displays information on all cameras (analog and network) connected to the Surveillix DVR Displaying More Columns The Camera Configuration tab can be customized to display the information you use most. Click Select Column to add or remove specific columns.
MOTION SETUP The DVR allows the user to adjust several different Motion Settings and create motion detection areas. Display full screen video pop up on motion event Beep on motion event Display full screen video pop up on sensor event Schedule recording at a regular specified interval Reduces Analog Signal Noise from Motion Detection Create a Motion Area 1. Click Motion in Setup. 2. Select a camera from the Select Camera list. 3. Select the Detect Detail Motion Area check box. 4. Click Clear.
Activating an Alarm on a Motion Event 1. In the Motion Setup window, select a camera to edit from the Camera list. 2. Create a motion area. 3. Select the Alarm Output check box. 4. Select a Control Output to activate for the selected camera. 5. Select an Alarm Duration time when a motion event occurs. Regular Interval Recording Regular Interval Recording allows users to record a single frame every few minutes or hours when there is no motion.
GENERAL SETUP Function Beep on Login Fail Enables the DVR to beep continuously in response to a failed login attempt. Only an authorized login will stop the beeping. Sequence Setting Allows the video out picture to automatically cycle through channels at a set speed. Example: .Cycle through channels 1-6 at four-second intervals. Display Options Use Full Screen Stretch the Surveillix interface to use the full monitor screen. Display Size Select from available monitor display sizes.
Connecting to a Wide Screen Display 1. Click Exit on the Display screen and select Exit in Windows Mode. 2. Right-click the Desktop and select Properties. 3. Click the Settings tab. 4. Drag the Screen Resolution bar to the proper resolution of the connected display. Tip Refer to the display documentation for the proper resolution settings. 5. Click OK and confirm the change. 6. Double-click the Surveillix Server icon on the Desktop. 7.
Volume The volume control allows fine tuning of the volume settings on the DVR. Volume Options: • Slider Controls – Used to adjust the literal volume for the respective devices listed. • Mute Check Box – Select the mute check box to mute volume on any of the device columns or select the Mute All check box to mute all audio on the DVR. Hybrid Sensor Setup This interface is used to link Hard Contact Sensor Inputs from supported Network Devices to the DVR Software.
Auto Sequence Setting Auto Sequencing is available either in the Display screen when Auto Sequencing has been enabled or when a Spot-Monitor out signal is used to display on a spot monitor. Auto Sequencing conveniently displays video channels at specified intervals and sequences through each selected channel.
SCHEDULE SETUP Recording Schedule The Recording Schedule window allows the user to create different recording schedules based on the day, time, and type of recording desired. In addition, this window contains the System Restart options that allow the user to perform basic system maintenance by automatically scheduling the DVR to restart periodically.
Sensor Schedule The Sensors will supersede all other types of recording modes (Motion and Continuous). Regardless of the recording schedule of a particular camera, if a sensor event occurs the associated cameras will begin recording as a Sensor Event. Sensor Recordings will be flagged and searchable using the Index Search Mode. Cameras are associated to sensors in the Camera Setup menu.
Create a Recording Schedule 1. Select a day to begin creating the schedule for -or- click Single Day Selection, enabling Multi Day Selection, to create the same schedule for multiple days. 2. Highlight the Time-Blocks within the Recording Schedule window for the camera(s) selected to schedule. Once the desired Time-Blocks are highlighted, click a Recording Mode button. The Time-Blocks should now appear Blue for Motion, Yellow for Continuous and White for No Recording.
Special Day Schedule The user can create days that have a unique recording schedule. If necessary create these on days that are ‘not typical’ such as Holidays, Special Events, etc. Special Day Mode / Normal Day Mode Date Bar Configured Special Days List Creating/Editing a ‘Special Day’ Schedule 1. Click Normal Day Mode to enable the Special Day Mode. 2. Select a day by typing the date or clicking the arrow to the right of the Date Bar. 3.
System Restart Setup System Restart Setup allows the user to define a schedule wherein the DVR automatically restarts according to specified parameters. Create System Restart Schedule 1. Click Schedule on the Setup screen. 2. Click Restart Setup. 3. Select the day(s) of the week to schedule an automatic system restart and select the check box to enable shut down. Note This step alone does not trigger the DVR to restart, only to shut down. 4.
NETWORK SETUP Network Setup allows the user to adjust settings such as Ports, setup emergency PPP information for use with the Emergency Agent and enable Remote Access. Settings for Video Sent to Remote Client Use with Emergency Agent Use with Remote Connections Enable RS-232 Keyboards (PTZ) Between DVR and Remote Client Time Out Value When attempting to connect to the DVR, if the connection does not succeed during the timeout period (seconds), the connection will be terminated.
ADMINISTRATIVE SETUP Select Date Log Data Display Export Log Data (1 to 7 days) Disk Management The Disk Management window is a native Windows function. This window displays the partition scheme and health status of the Hard Disk Drives in the DVR. This window is often used to troubleshoot a DVR, or verify the amount of Hard Drive storage installed. For more information about Disk Management, consult a Windows XP manual.
User Management The User Management Console allows the administrator to create, edit, and delete user accounts. Each user account can be assigned different privileges to limit the usage of the DVR system. Users can be given administrator privileges by enabling all rights, however only the true administrator account can log into the User Management Console.
User Rank The User Ranking structure allows the option to assign a privilege system (1-10 where one has the most rights) to users of the DVR Software. For example. Since only one user is allowed to use the PTZ controls at any one time, an administrator with a higher rank can kick another user out and take control of the PTZ. The User Rank option affects: SETUP ACCESS - The DVR Software can only have 1 user accessing Setup at any given time.
Status Check / Email General 1. Click Setup on the Display screen. 2. Click Administrative. 3. Click Status Check/Email. 4. Select the Enable Email Alarm check box. 5. Enter a From Name and e-mail Address. Note This name and address will appear in the From line of the email alert message. 6. Enter the SMTP information for the “From” email account. Contact the email administrator for this information if necessary. 7.
Storage Check 1. Set up the General and Users tabs first. (see above) 2. Select the Use Storage Check check box. 3. Define the number of minutes. 4. Select an Alert Option, Beep or Popup Message, if desired. 5. Click Apply. Recording Data Check 1. Setup the General and Users tabs first. (see above) 2. Select the Recording Data Check check box. 3. Define the number of hours between data checks. 4. Select the Action Method. 5. Click Apply.
SMART Information The SMART Information tab displays Hard Drive information. SMART Alert 1. Setup the General and Users tabs first. (see above) 2. Select the Enable SMART Alarm. 3. Define the number hours between SMART checks. 4. Select the type of SMART event to trigger an action. 5. Define the maximum HDD temperature. 6. Select an action method. 7. Click Apply. Alarm Event 1. Setup the General and Users tabs first. (see above) 2. Select the Use Email Alarm check box. 3.
HDD Management HDD Management allows you to select drives to record data and add network drives.
INFORMATION The Information display allows users to define the site code necessary for connecting to remote software, save comments relative to the DVR and store tech support and contact number information. Total HDD /Available HDD Space Current Server Software Version User-Defined Contact Numbers Enter comments Site Code A user-specified unique identification name used by other DVR software to identify the DVR.
SEARCH This chapter includes the following information: • Search Overview • Daylight Saving Time • Index Search • Preview Search • Graphic Search • Motion Search
SEARCH OVERVIEW The DVR has several options that allow the user to easily search through, and find, a particular section of video. From Motion/Sensor indexing to calendar views highlighting days with recorded video; the DVR is equipped to help the user quickly find a specific video or event. The following chapter describes how to use the DVR Search features.
Adjust the Brightness of an Image 1. Select an image to adjust by double-clicking on the desired image. Multiple images cannot be adjusted at one time. 2. Move the Brightness slide bar to the right or left to adjust the brightness. 3. Reset the Brightness by moving the slider back to the center of the bar. Zooming in on an Image 1. Select an image to adjust by double-clicking on the desired image. Multiple images cannot be adjusted at one time. 2.
PERFORMING A BASIC SEARCH There are several different types of searches that can be performed on the DVR. The most basic involves selecting the date, time, camera, and clicking play. 1. Click the Calendar button to select a date. 2. Select a time by clicking the up and down arrows to the right of the time display. 3. Click OK. 4. Select one or more cameras. 5. Click Play. Video can be played forwards, backwards, or frame-by-frame. PRINTING AN IMAGE 1.
SAVE TO JPG OR AVI The DVR can export single images in a JPG Image file format and save video clips in an AVI format. Both JPG and AVI file formats are the most commonly used graphical formats today. Virtually every computer offers some type of support for these file formats which make them the most ideal formats to use. JPG Optimized for compressing full-color or grayscale photographic images, JPG images are 24-bit (16.7 million color) graphics. Use JPG to export a single image or frame.
Bookmarks Use bookmarks to mark a video clip during a search. Export bookmarked data using the Clip Backup feature. 1. Perform a search for the desired video. 2. Stop playback at the beginning of the desired clip. 3. Right-click the video and select Start Bookmark. 4. Click the play button to continue playback. 5. Stop playback at the end of the desired clip. 6. Right-click the video at the desired end point and select End Bookmark. 7. Type a name to identify the bookmark in the Title box.
Single Clip Backup Along with the Save option, a single camera backup option is also included with the Surveillix software. The single Camera or Clip Backup allows the user to backup a single camera without hAVIng to backup multiple cameras at a given time. The Clip Backup option gives the users the ability to choose a backup time frame, choose a specific camera, add memos, and even make a copy for the Backup Viewer if needed. 1. From the Search screen, click Save. 2.
INDEX SEARCH Using the Index Search can greatly decrease the amount of time spent searching through saved video. The Index Search allows a user to perform a search based on criteria such as Sensor, Motion and Instant Record events Performing an Index Search 1. Click the Calendar button on the Search screen to select the date to search. 2. Click Index Search. 3. Select the cameras and sensors to include in the search. 4. Select the Select Time check box to define a specific period. 5.
PREVIEW SEARCH Preview Search can be used in a number of circumstances to quickly find an exact moment where an event, such as a theft, occurred. The Preview Search gives a 24 Hour visual overview of a single camera by separating a 24 hour period (1 day) into 24 images, one image for each hour of the day. The search can then be further narrowed down into ten minute increments and one minute increments by selecting one of the images displayed. These example images show how the Preview Search functions.
Performing a Preview Search 1. Select a single camera by either turning off all cameras but one or double-clicking a displayed image. 2. Click Preview Search. 24 images display. If there is no recorded video during a portion of the day, “No Image” will be displayed where the image should be. 3. Refine the search by double-clicking on an image to select it. 6 images display. If needed, return to the previous 24-image view by right-clicking on an image. 4.
OBJECT SEARCH Object Search is a powerful search utility that is used to search a region on the video for any motion changes. Results are neatly displayed and can be viewed quickly. Performing an Object Search 1. Perform a Basic Search. See the instructions on Performing a Basic Search. 2. Select a single camera, either by turning off all cameras but one or by double-clicking a displayed image. 3. Click Object Search on the Search screen. 4.
MOTION SEARCH The Motion Search provides a dynamic display of the levels of motion in recorded video. Adjust the level of motion to only play clips of video at or above that level. Tip To enable motion data to be saved for Motion search, ensure that you select the following settings: On the Motion setup page under Motion Regions, select the Detect Detail Motion Area check box. On the General setup page under Display, select the Motion Detect on Continuous Recording check box.
SEARCH IN LIVE The Search in Live feature allows users to review events immediately while monitoring live video. Pause, rewind, and resume live video within seconds of an alarm event or suspicious activity. 1. Move the mouse cursor over the desired live video display on the Live Display screen. 2. Press the scroll button on the mouse. 3. The search in live Controls will display at the bottom of the image. 4. Use the controls to pause, rewind, move frame-by-frame or resume playing as desired.
NOTES:
PAN / TILT / ZOOM This chapter includes the following information: • Overview • Setting up the PTZ • Creating and Viewing a Preset Position • Creating and Viewing a Preset Pattern
PAN / TILT / ZOOM OVERVIEW The PTZ controls within the DVR allow for powerful control over the cameras. This can be extremely beneficial by increasing the usefulness of the recorded video. Using the PTZ controls you can create custom preset configurations that can continuously sweep across large areas. NOTE PTZ setup and control is only available for supported video encoders with a PTZ RS-485 pass-through. SETTING UP A PTZ CAMERA Setting up a PTZ Camera is simple.
ADVANCED PTZ SETUP PTZ signal type Adjust Speed Settings Connection Settings Note Preset and Tour options may vary depending on the camera Creating and Viewing Preset Positions A Preset Position is a user-defined location where the camera can be pointed, zoomed in, and focused. Preset positions can be defined and labeled if the camera supports this. Creating a Preset 1. Inside Setup, click PTZ and select the camera. 2. If the camera is already selected click Open PTZ Controller. 3.
PTZ Address Settings Some protocols support software address settings. The RX Addresses and ID settings are compatible with a particular line of receivers that support 2 ID addresses. The PT Driver Address is associated with the PTZ ID address set on the camera. The addresses must match for the DVR to communicate with the proper PTZ camera. This is especially important when a large number of PTZ cameras are connected to the DVR.
CONTROLLING A PTZ CAMERA The Surveillix DVRs provide control for a PAN/TILT/ZOOM camera in two different ways. The first method is to use the Graphical PTZ Controller that appears when the PTZ button is clicked on the Display screen. The second method is to use the mouse to control the camera directly from the live video display. (On-Screen Compass) Using the Graphical PTZ Controller 1. Use the Arrow buttons to control the direction of the PTZ camera. 2.
Using the On-Screen Compass 1. Click Setup on the Display screen. 2. Click PTZ. 3. Select the On Screen Compass check box to enable the feature. 4. Click Apply. 5. Click Exit to return to the Display screen. 6. Click PTZ. 7. Control the PTZ by dragging the mouse on the screen in the desired direction. Note A green line will appear to show the direction the PTZ will move. The shorter the line the less the PTZ will move.
PTZ Tour Schedule Hours 0-23 (24 hours) Cameras Create PTZ Tour Schedule 1. Click Setup on the Display screen. 2. Click PTZ. 3. Click Tour Schedule to open the PTZ Tour Schedule window. 4. In Single Select Mode select one day of the week to create a schedule for or toggle to Multi Select Mode to select multiple days with the same schedule. 5. Click and drag the mouse cursor to select blocks of time (hours 0-24) and corresponding cameras. 6. Click Select. 7.
NOTES:
BACKING UP VIDEO DATA This chapter includes the following information: • Overview • Saving Video to a DVD • Saving Video from a Single Camera • Scheduling Regular Video Backup
BACKUP OVERVIEW The Backup Center allows you to back up recorded video data from multiple dates and times to one or more locations including the DVD-RW drive, Network Storage Locations, and External Hard Drives. The DVR can easily backup important video data to an internal or external media location. The most commonly used forms of this are CD-R/RWs, External USB or FireWire Hard Drives, and Network Drives. Every DVR comes equipped with a DVD-RW drive, USB port, and Network Adapter.
General Screen Overview The General Backup Screen is used for performing bulk backup of video recorded by all cameras for a selected period, or periods, to a specified storage location. Calendar Select Additional Drive/Folder Define Drive Priority Select Remote Network Location Hour / Minutes Recording data displays in hourly (24 horizontal columns) and 10-minute (6 vertical cells) segments. Green cells indicate time with recorded video. Red cells indicate time selected for backup.
Clip Screen Overview The Clip Screen is used for backing up video recorded by individual cameras for a selected period of time to a specified storage location Performing a Clip Backup 1. Click Backup on the Display screen. 2. Click the Clip tab at the top of the Backup Center window. 3. Set the Start Time and End Time under Time Setup. 4. Select the cameras to back up in the Channel Selection box. 5. Select the Backup Drive to save the backup video to. 6.
Scheduled Screen Overview The Scheduled Backup Screen is used for performing bulk backup of video recorded by all cameras for a selected period, on a regular scheduled basis (1-24 hours). The Scheduled Backup Screen is similar to the General Backup Screen. Performing a Scheduled Backup 1. Click Backup on the Display screen. 2. Click the Schedule tab at the top of the Backup Center window. 3. Select the blocks of time to back up using the Hour/Minute Grid.
NOTES:
LAN / ISDN / PSTN CONNECTIONS This chapter includes the following information: • Overview • Configuring TCP/IP Settings • Connecting to a LAN • LAN / ISDN / PSTN Connections
LAN OVERVIEW The DVR can be easily connected to a Local Area Network (LAN) and uses Microsoft’s® powerful and secure Windows® XP Embedded operating system. This allows for easy and well-documented instructions on setting up LAN connections no matter what type of LAN you want to use. A LAN is a group of computers and other devices dispersed over a relatively limited area and connected by a communications link that allows one device to interact with any other on the network.
LDAP INTEGRATION This chapter includes the following information: • Installing LDAP
FEATURES The instructions below are for LDAP Integration with Server Software version 3.6.36 and above. • DVR server does not need to be joined to the Domain. The DVR server will query the LDAP server for accounts and authorization levels. • The DVR server creates groups within Active Directory for each of the permissions on the DVR. Simply join a Domain user to these groups to provide access to that function in the DVR.
4. Go to the Active Directory Users and Computers application. You should now see an OU called DVR with an OU inside of it named the same as the Site Code above (example 100-000). 5. You can now add users within Active Directory to the groups the DVR has created. When a user belongs to a group he or she will have access (or be denied access in the case of Audio or Camera channels) to that permission on any DVRs with that site code.
NOTES:
WEB VIEWER This chapter includes the following information: • Overview • Configuring the Web Viewer
WEB VIEWER OVERVIEW The DVR allows you to access video using Microsoft® Internet Explorer® 7. Highlights: View Live Video from most computers Username and Password protected Easy to use graphical interface Basics: 75 users can access the Web DVR simultaneously. The Web Viewer is an easy, secure way to view live video from virtually any computer with an internet connection using Microsoft Internet Explorer. In order to log in to the DVR server, a user account must be made for the user.
Configuring the Server for Remote Connection 1. Click Setup on the main display screen. 2. Click Network. 3. Clear the Disable Remote Control check box. You should now be allowed to adjust port settings if necessary. NOTE: If you are using a Firewall, it may be necessary to adjust the port settings on both the DVR and the Firewall. Contact the Network Administrator for more information. 4. Select the Web Viewer (iDVR) check box. 5. Click Apply. 6. Make sure a User account is created.
INCLUDED SOFTWARE SETUP This chapter includes the following information: • Emergency Agent Overview • Remote Software Overview • Digital Verifier • Backup Viewer
EMERGENCY AGENT OVERVIEW The Emergency Agent software is a utility that streams video across a Local Area Network to a Client PC when an alarm is detected on the DVR. The video that streams across can be stopped, played forwards and backwards, in slow motion or real speed. The utility is loaded at startup and placed in the taskbar. It constantly monitors for a signal from the DVR.
Setup Window Network Port Indicates the port which the Emergency Agent uses to listen for incoming events. This number should be changed to the same number as is set in the Emergency Port in Network Settings on the DVR. Save Directory Sets the location that recorded video footage is saved to. Notice Options Configuration settings for activating an audible indicator or popup window when the Emergency Agent receives an event.
Add Items to Alarm Confirm List 1. From the Option menu, click Setup. 2. Type the desired text in the box below the Alarm Confirmation List. NOTE: The items in the Alarm Confirmation List will be available on a list under Status Setting in main Emergency Agent screen. 3. Click Add. 4. Click OK to save changes and close the window.
SEARCH ALARM WINDOW Video Display Play Controls Go to Next Event Go to Previous Event Alarm Event Information Export Quality It may be necessary to reduce the overall size of an AVI file; for example, to email to someone. AVI file sizes can be reduced by reducing the image quality. However, reducing the image quality causes the AVI video to appear more pixilated. When size is not an issue, setting quality to 100 is highly recommended.
REMOTE SOFTWARE OVERVIEW The DVR was specifically designed to be fully operated and maintained remotely. It connects using the standard TCP/IP protocol thorough connection types such as DSL, Cable Mode, T1, ISDN, 56K Modem, LAN, and more. The Surveillix Remote software allows you to view live video, search through archived video, export images and video clips and have virtually full Setup control. Surveillix Remote Software is Microsoft Vista® compatible.
Remote Software Setup Installing Remote Software 1. On the client computer, insert the Surveillix Software CD into the CD-ROM. The CD should play automatically. 2. When prompted, select the Install Remote Software option. Follow the installation instructions carefully. 3. When the software finishes installing, close any open installation windows. Create a New Remote Connection DVR Site List Import/Export saved configurations Selected Site Information 1.
Configuring the DVR In order to access the DVR remotely, the DVR Server must be setup to allow remote connections. Time Out Value Specifies a value (in seconds) to wait for a signal from the Surveillix Remote Client. If a signal is not received by that time, the connection is dropped. Center Port Used to transfer the connection data. Image Port Used to transfer the image data. Search Port Used to transfer the search data. Configuring the Server for Remote Connection 1. Enter Setup on the DVR.
DIGITAL VERIFIER OVERVIEW JPG images and AVI video files that are exported from the Digital Video Recorder are automatically embedded with a digital signature. Digital Signatures are a way to verify the authenticity of the images to ensure that they have not been tampered with or edited in any way. Included on the Software Installation DVD supplied with the DVR is the Digital Signature Verification program. This program can be installed on any computer and loads an image in question.
BACKUP VIEWER OVERVIEW The Backup Viewer allows you to play back the exported video in its proprietary format. Video saved in this format is extremely difficult to tamper with and therefore is the ideal solution when law enforcement and the legal department are involved. This video cannot be read by any other viewer. The Backup Viewer operates essentially like the Search portion of the DVR software. For detailed explanations of these functions, refer to the chapter on Search Options in this manual.
SCS OVERVIEW SCS software is Network DVR Management Software; a powerful utility that allows 100 or more DVRs to be controlled using one computer. This software allows you to view live video, search saved video, edit and configure setup on each DVR, and import maps of buildings and other locations. The SCS software was specifically designed as an enterprise software solution.
