Operation Manual

78
79
Others
Compatible input signal list
The following table shows compatible signal types, their resolution and frequency refresh rates.
Horizontal: 15 kHz, 31 kHz to 90 kHz, Vertical: 50 Hz to 85 Hz
Signal Resolution (DPI)
Frequency Refresh
Rate (KHz)
Frequency Refresh
Rate (Hz)
NTSC - 15.73 60.00
PAL - 15.63 50.00
PAL60 - 15.73 60.00
SECAM - 15.63 50.00
VESA D 640 x 480 31.47 59.94
MAC D 640 x 480 35.00 66.67
VESA D 640 x 480 37.86 72.81
VESA D 640 x 480 37.50 75.00
VESA D 640 x 480 43.27 85.01
VESA D 800 x 600 35.16 56.25
VESA D 800 x 600 37.88 60.32
VESA D 800 x 600 48.08 72.19
VESA D 800 x 600 46.88 75.00
VESA D 800 x 600 53.67 85.06
MAC D 832 x 624 49.72 74.55
VESA D 1024 x 768 48.36 60.00
VESA D 1024 x 768 56.48 70.07
MAC D 1024 x 768 60.24 74.93
VESA D 1024 x 768 60.02 75.03
VESA D 1024 x 768 68.68 85.00
VESA D 1152 x 864 67.50 75.00
VESA D 1280 x 768 47.80 60.00
VESA D 1280 x 768 60.30 75.00
VESA D 1280 x 768 68.60 85.00
VESA D 1280 x 800 49.70 60.00
VESA D 1280 x 800 62.80 75.00
VESA D 1280 x 800 71.60 85.00
VESA D 1280 x 960 60.00 60.00
VESA D 1280 x 1024 63.98 60.02
VESA D 1400 x 1050 65.30 60.00
VESA D 1440 x 900 55.90 60.00
VESA D 1440 x 900 70.60 75.00
HDTV (1080i)(1125i) - 1920 x 1080 33.75 60.00 Interlace
HDTV (1080i)(1125i) - 1920 x 1080 28.13 50.00 Interlace
HDTV (720p)(750p) - 1280 x 720 45.00 60.00 Progressive
HDTV (720p) - 1280 x 720 37.50 50.00 Progressive
SDTV (576p)(625p) - - 31.25 50.00 Progressive
SDTV (480p)(525p) - - 31.47 59.94 Progressive
DVD YCbCr - - 15.73 59.94 Interlace
DVD YCbCr - - 15.63 50.00 Interlace
Note
Images above agged with “D” are supported by digital signal.
An image with higher or lower resolution than the projector’s native resolution
(1280 x 800) will be compressed.
Some Composite and Sync on Green signals may not be displayed correctly.
Signals other than those specied in the table above may not be displayed correctly. If
this should happen, change the refresh rate or resolution on your PC. Refer to Display
Properties help section of your PC for procedures.

•
•
•
•
Specications (Continued)
CONTROL terminal
Pin assignment
Pin
No.
Signal Name Description
D sub 9 pin connector
1 DCD Data carrier detect
2 RXD Receiving data
3 TXD Sending data
4 DTR Data terminal ready
5 GND Signal ground
6 DSR Data set ready
7 RTS Request to send
8 CTS Consent to send
9 RI Ring indicator
Note
Use a cross cable (not supplied) for RS232C control.
Interface format
<Command format>
Header: ‘#’
Delimiter: CR (0x0Dh)
Command: 3 Byte (ASCII Character)
Parameter: Variable length
(If the command has a parameter, place a colon before the parameter.)
<Response format>
Header:
‘=’
Delimiter CR (0x0Dh)
Command 3 Byte (ASCII Character, command echo)
Parameter Variable length
(If the command has a parameter, place a colon before the parameter.)
Main Commands
Item Command
Power off PON
Shutdown PSD
Status display on DON
Status display off DOF
Note
Contact your dealer for control cable and other commands.


•


•