TOSHIBA TE2000 Portable Personal Computer User’s Manual
Copyright © 2001 by TOSHIBA Corporation. All rights reserved. Under the copyright laws, this manual cannot be reproduced in any form without the prior written permission of TOSHIBA. No patent liability is assumed, with respect to the use of the information contained herein. TOSHIBA TE2000 Portable Personal Computer User’s Manual First edition January 2002 Disclaimer This manual has been validated and reviewed for accuracy.
EU Declaration of Conformity TOSHIBA declares, that the product: PS600* conforms to the following Standards: Supplementary Information: “The product complies with the requirements of the Low Voltage Directive 73/23/EEC, the EMC Directive 89/336/EEC and/or the R&TTE Directive 1999/05/EEC.” This product is carrying the CE-Mark in accordance with the related European Directives. Responsible for CE-Marking is TOSHIBA Europe, Hammfelddamm 8, 41460 Neuss, Germany.
Network Compatibility Statement This product is designed to work with, and is compatible with the following networks. It has been tested to and found to conform with the additional requirements conditional in EG 201 121.
Pursuant to FCC CFR 47, Part 68: When you are ready to install or use the modem, call your local telephone company and give them the following information: ❑ The telephone number of the line to which you will connect the modem ❑ The registration number that is located on the device The FCC registration number of the modem will be found on either the device which is to be installed, or, if already installed, on the bottom of the computer outside of the main system label.
If problems arise If any of your telephone equipment is not operating properly, you should immediately remove it from your telephone line, as it may cause harm to the telephone network. If the telephone company notes a problem, they may temporarily discontinue service. When practical, they will notify you in advance of this disconnection. If advance notice is not feasible, you will be notified as soon as possible.
The customer should be aware that compliance with the above conditions may not prevent degradation of service in some situations. Repairs to certified equipment should be coordinated by a representative designated by the supplier. Any repairs or alterations made by the user to this equipment, or equipment malfunctions, may give the telecommunications company cause to request the user to disconnect the equipment.
Notes for Users in Australia and New Zealand Modem warning notice for Australia Modems connected to the Australian telecoms network must have a valid Austel permit. This modem has been designed to specifically configure to ensure compliance with Austel standards when the country/region selection is set to Australia. The use of other country/region setting while the modem is attached to the Australian PSTN would result in you modem being operated in a non-compliant manner.
❑ Some parameters required for compliance with Telecom’s PTC Specifications are dependent on the equipment (PC) associated with this modem.
❑ The transmit level from this device is set at a fixed level and because of this there may be circumstances where the performance is less than optimal. Before reporting such occurrences as faults, please check the line with a standard Telepermitted telephone, and only report a fault if the phone performance is impaired. ❑ It is recommended that this equipment be disconnected from the Telecom line during electrical storms.
Information to Wireless LAN User Wireless Interoperability The TOSHIBA Wireless LAN Mini PCI Card products are designed to be interoperable with any Wireless LAN product that is based on Direct Sequence Spread Spectrum (DSSS) radio technology, and is compliant to: ❑ The IEEE 802.11 Standard on Wireless LANs (Revision B), as defined and approved by the Institute of Electrical and Electronics Engineers.
Canada – Industry Canada (IC) This device complies with RSS 210 of Industry Canada. Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of this device.
L’utilisation en extérieur est autorisé sur le canal 10 (2457 MHz) et 11 (2462 MHz). Dans le cas d’une utilisation privée, à l’extérieur d’un bâtiment, au-dessus d’un espace public, aucun enregistrement n’est nécessaire pour une distance de moins de 300m. Pour une distance supérieure à 300m un enregistrement auprès de I’IBPT est requise. Pour une utilisation publique à I’extérieur de bâtiments, une licence de I’IBPT est requise. Pour les enregistrements et licences, veuillez contacter I’IBPT.
USA-Federal Communications Commission(FCC) This device complies with Part 15 of FCC Rules. Operation of the devices in a Wireless LAN System is subject to the following two conditions: ❑ This device may not cause harmful interference. ❑ This device must accept any interference that may cause undesired operation. Caution: Exposure to Radio Frequency Radiation. The radiated output power of the TOSHIBA Wireless LAN Mini PCI Card is far below the FCC radio frequency exposure limits.
❑ Connect the equipment to an outlet on a circuit different from that to which the receiver is connected. ❑ Consult the dealer or an experienced radio/TV technician for help. TOSHIBA is not responsible for any radio or television interference caused by unauthorized modification of the devices included with this TOSHIBA Wireless LAN Mini PCI Card, or the substitution or attachment of connecting cables and equipment other than specified by TOSHIBA .
1. Sticker Please put the following sticker on devices incorporating this product. In the frequency bandwidth of this equipment, industrial device, scientific device, medical device like microwave oven, licensed premises radio station and non-licensed specified low-power radio station for mobile object identification system (RF-ID) that is used in product line of factories, (Other Radio Stations)are used.
3. TOSHIBA Direct PC Monday — Friday : 10:00 — 17:00 Toll Free Tel : 0120-13-1100 Direct Dial : 03-3457-5916 FAX : 03-5444-9450 Electronic communication device authorization This device obtains the Technical Conditions Compliance Approval, and it belongs to the device class of radio equipment of low-power data communication system radio station stipulated in the Telecommunications Business Law. The following restrictions apply: ❑ Do not disassemble or modify the device.
United States of America and Canada Tested To Comply With FCC Standards FOR HOME OR OFFICE USE. See FCC 47CFR part 15.19(b)(2) This device complies with part15 of the FCC rules and with RSS-210 / RSS-139 of the Industry Canada. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation.
TOSHIBA DVD-ROM drive SD-C2502** safety instruction ** means any letters or numbers. CAUTIONS: 1. The DVD-ROM drive employs a laser system. To ensure proper use of this product, please read this instruction manual carefully and retain for future reference. Should the unit ever require maintenance, contact an authorized service location. 2. Use of controls, adjustments or the performance of procedures other than those specified may result in hazardous radiation exposure. 3.
CAUTION: This appliance contains a laser system and is classified as a “CLASS 1 LASER PRODUCT.” To use this model properly, read the instruction manual carefully and keep this manual for your future reference. In case of any trouble with this model, please contact your nearest “AUTHORIZED service station.” To prevent direct exposure to the laser beam, do not try to open the enclosure.
VAROITUS. Suojakoteloa si saa avata. Laite sisältää laserdiodin, joka lähetää näkymätöntä silmilie vaarallista lasersäteilyä. CAUTION: USE OF CONTROLS OR ADJUSTMENTS OR PERFORMANCE OF PROCEDURES OTHER THAN THOSE SPECIFIED IN THE OWNER’S MANUAL MAY RESULT IN HAZARDOUS RADIATION EXPOSURE. VORSICHT: DIE VERWENDUNG VON ANDEREN STEURUNGEN ODER EINSTELLUNGEN ODER DAS DURCHFÜHREN VON ANDEREN VORGÄNGEN ALS IN DER BEDIENUNGSANLEITUNG BESCHRIEBEN KÖNNEN GEFÄHRLICHE STRAHLENEXPOSITIONEN ZUR FOLGE HABEN.
Location Locationofofthe therequired required label label COMPLIES WITH FDA RADIATION PERFORMANCE STANDARDS, 21 CFR SUBCHAPTER J. MANUFACTURED: Manufactured by Kyushu Matsushita Electric Co., Ltd. 1-62 4-Chome Minoshima, Hakata-Ku Fukuoka,Japan CAUTION: This appliance contains a laser system and is classified as a “CLASS 1 LASER PRODUCT.” To use this model properly, read the instruction manual carefully and keep this manual for your future reference.
ADVERSEL: USYNLIG LASERSTRÅLING VED ÅBNING, NÅR SIKKERHEDSAF-BRYDER ER UDE AF FUNKTION. UNDGÅ UDSÆTTELSE FOR STRÅLING ADVARSEL: Denne mærking er anbragt udvendigt på apparatet og indikerer, at apparatet arbejder med laserstråler af klasse 1, hviket betyder, at der anvendes laserstrlier af svageste klasse, og at man ikke på apparatets yderside kan bilve udsat for utilladellg kraftig stråling.
Matsushita CD-RW/DVD-ROM drive UJDA720** safety instruction ** means any letters or numbers. CAUTIONS: 1. The CD-RW/DVD-ROM drive employs a laser system. To ensure proper use of this product, please read this instruction manual carefully and retain for future reference. Should the unit ever require maintenance, contact an authorized service location. 2. Use of controls, adjustments or the performance of procedures other than those specified may result in hazardous radiation exposure. 3.
CAUTION: This appliance contains a laser system and is classified as a “CLASS 1 LASER PRODUCT.” To use this model properly, read the instruction manual carefully and keep this manual for your future reference. In case of any trouble with this model, please contact your nearest “AUTHORIZED service station.” To prevent direct exposure to the laser beam, do not try to open the enclosure.
VAROITUS. Suojakoteloa si saa avata. Laite sisältää laserdiodin, joka lähetää näkymätöntä silmilie vaarallista lasersäteilyä. CAUTION: USE OF CONTROLS OR ADJUSTMENTS OR PERFORMANCE OF PROCEDURES OTHER THAN THOSE SPECIFIED IN THE OWNER’S MANUAL MAY RESULT IN HAZARDOUS RADIATION EXPOSURE. VORSICHT: DIE VERWENDUNG VON ANDEREN STEURUNGEN ODER EINSTELLUNGEN ODER DAS DURCHFÜHREN VON ANDEREN VORGÄNGEN ALS IN DER BEDIENUNGSANLEITUNG BESCHRIEBEN KÖNNEN GEFÄHRLICHE STRAHLENEXPOSITIONEN ZUR FOLGE HABEN.
Location of the required label PRODUCT IS CERTIFIED BY THE MANUFACTURER TO COMPLY WITH DHHS RULES 21 CFR SUBCHAPTER J APPLICABLE AT THE DATE OF MANUFACTURE. MANUFACTURED: TOSHIBA CORPORATION 1-1, SHIBAURA 1-CHOME MINATO-KU, TOKYO 105-8001, JAPAN CAUTION: This appliance contains a laser system and is classified as a “CLASS 1 LASER PRODUCT.” To use this model properly, read the instruction manual carefully and keep this manual for your future reference.
ADVERSEL: USYNLIG LASERSTRÅLING VED ÅBNING, NÅR SIKKERHEDSAF-BRYDER ER UDE AF FUNKTION. UNDGÅ UDSÆTTELSE FOR STRÅLING ADVARSEL: Denne mærking er anbragt udvendigt på apparatet og indikerer, at apparatet arbejder med laserstråler af klasse 1, hviket betyder, at der anvendes laserstrlier af svageste klasse, og at man ikke på apparatets yderside kan bilve udsat for utilladellg kraftig stråling.
TEAC DVD-ROM drive DV-28E** safety instruction ** means any letters or numbers. This product has been designed and manufactured according to FDA regulations "title 21. CFR. chapter 1, subchapter J. based on the radiation Control for Health and Safety Act of 1968," and is classified as a class 1 laser product. There is no hazardous invisible laser radiation confined in the protective housings. The label required in this regulation is shown below.
CAUTION: This appliance contains a laser system and is classified as a “CLASS 1 LASER PRODUCT.” To use this model properly, read the instruction manual carefully and keep this manual for your future reference. In case of any trouble with this model, please contact your nearest “AUTHORIZED service station.” To prevent direct exposure to the laser beam, do not try to open the enclosure.
OBS! Apparaten innehåller laserkomponent som avger laserstråining överstigande gränsen för laserklass 1. VAROITUS. Suojakoteloa si saa avata. Laite sisältää laserdiodin, joka lähetää näkymätöntä silmilie vaarallista lasersäteilyä. CAUTION: USE OF CONTROLS OR ADJUSTMENTS OR PERFORMANCE OF PROCEDURES OTHER THAN THOSE SPECIFIED IN THE OWNER’S MANUAL MAY RESULT IN HAZARDOUS RADIATION EXPOSURE.
Optical pickup Type : PU-2200 Manufacturer : TEAC CORPORATION Laser output lens : Less than 0.25m W on the objective Wavelength : 795nm Location of the required label THIS PRODUCT COMPLIES WITH DHHS RULES 21 CFR CHAPTER 1, SUBCHAPTER J APPLICABLE AT DATE OF MANUFACTURE. MANUFACTURED: Manufactured by TEAC Corporation 3-7-3 Naka-cho, Musashino-shi, Tokyo, Japan CAUTION: This appliance contains a laser system and is classified as a “CLASS 1 LASER PRODUCT.
CLASS 1 LASER PRODUCT LASERSCHUTZKLASSE 1 PRODUKT TO EN60825 ADVERSEL: USYNLIG LASERSTRÅLING VED ÅBNING, NÅR SIKKERHEDSAF-BRYDER ER UDE AF FUNKTION. UNDGÅ UDSÆTTELSE FOR STRÅLING VORSICHT: Dieses Gerät enthält ein Laser-System und ist als “LASERSCHUTZKLASSE 1 PRODUKT” klassifiziert. Für den richtigen Gebrauch dieses Modells lesen Sie bitte die Bedienungsanleitung sorgfältig durch und bewahren diese bitte als Referenz auf.
CAUTION: USE OF CONTROLS OR ADJUSTMENTS OR PERFORMANCE OF PROCEDURES OTHER THAN THOSE SPECIFIED IN THE OWNER’S MANUAL MAY RESULT IN HAZARDOUS RADIATION EXPOSURE. VORSICHT: DIE VERWENDUNG VON ANDEREN STEURUNGEN ODER EINSTELLUNGEN ODER DAS DURCHFÜHREN VON ANDEREN VORGÄNGEN ALS IN DER BEDIENUNGSANLEITUNG BESCHRIEBEN KÖNNEN GEFÄHRLICHE STRAHLENEXPOSITIONEN ZUR FOLGE HABEN. TEAC CD-R/RW drive CD-W28E** safety instruction ** means any letters or numbers.
Location of the required label THIS PRODUCT COMPLIES WITH DHHS RULES 21 CFR CHAPTER 1, SUBCHAPTER J APPLICABLE AT DATE OF MANUFACTURE. MANUFACTURED: Manufactured by TEAC Corporation 3-7-3 Naka-cho, Musashino-shi, Tokyo, Japan CAUTION: This appliance contains a laser system and is classified as a “CLASS 1 LASER PRODUCT.” To use this model properly, read the instruction manual carefully and keep this manual for your future reference.
ADVERSEL: USYNLIG LASERSTRÅLING VED ÅBNING, NÅR SIKKERHEDSAF-BRYDER ER UDE AF FUNKTION. UNDGÅ UDSÆTTELSE FOR STRÅLING ADVARSEL: Denne mærking er anbragt udvendigt på apparatet og indikerer, at apparatet arbejder med laserstråler af klasse 1, hviket betyder, at der anvendes laserstrlier af svageste klasse, og at man ikke på apparatets yderside kan bilve udsat for utilladellg kraftig stråling.
HITACHI DVD-ROM drive GDR-8081N** safety instruction ** means any letters or numbers. CAUTIONS: 1. The DVD-ROM drive employs a laser system. To ensure proper use of this product, please read this instruction manual carefully and retain for future reference. Should the unit ever require maintenance, contact an authorized service location. 2. Use of controls, adjustments or the performance of procedures other than those specified may result in hazardous radiation exposure. 3.
CAUTION: This appliance contains a laser system and is classified as a “CLASS 1 LASER PRODUCT.” To use this model properly, read the instruction manual carefully and keep this manual for your future reference. In case of any trouble with this model, please contact your nearest “AUTHORIZED service station.” To prevent direct exposure to the laser beam, do not try to open the enclosure.
OBS! Apparaten innehåller laserkomponent som avger laserstråining överstigande gränsen för laserklass 1. VAROITUS. Suojakoteloa si saa avata. Laite sisältää laserdiodin, joka lähetää näkymätöntä silmilie vaarallista lasersäteilyä. CAUTION: USE OF CONTROLS OR ADJUSTMENTS OR PERFORMANCE OF PROCEDURES OTHER THAN THOSE SPECIFIED IN THE OWNER’S MANUAL MAY RESULT IN HAZARDOUS RADIATION EXPOSURE.
Table of Contents Preface Manual contents ............................................................................... xlvii Conventions ...................................................................................... xlvii Abbreviations ..................................................................................... xlvii Icons .................................................................................................. xlvii Keys .........................................................
Slim Select Bay modules ................................................................. 2-11 DVD-ROM drive ............................................................................... 2-12 CD-ROM drive .................................................................................. 2-13 CD-R/RW drive ................................................................................ 2-13 CD-RW/DVD-ROM drive ..................................................................
Using 3 1/2" external diskette drive ................................................ 4-10 Connecting 3 1/2" diskette drive ....................................................... 4-11 Disconnecting 3 1/2" diskette drive ................................................... 4-12 Diskette care .................................................................................... 4-12 Wireless communications ............................................................... 4-13 Wireless LAN ........................
Power indicators ................................................................................ 6-4 Battery indicators ................................................................................ 6-4 DC IN indicator ................................................................................... 6-4 Power indicator ................................................................................... 6-5 Battery types ....................................................................................
Additional AC adaptor ........................................................................ 8-9 Battery charger ................................................................................... 8-9 Slim Select Bay HDD adaptor ............................................................ 8-9 USB diskette drive ............................................................................ 8-11 Advanced Port Replicator ................................................................ 8-11 Parallel printer ...
Hibernation ....................................................................................... 9-22 Memory expansion ........................................................................... 9-23 LAN .................................................................................................. 9-23 Wireless LAN ................................................................................... 9-24 Toshiba support ...............................................................................
Preface Congratulations on your purchase of the TOSHIBA TE2000 series computer. This powerful, lightweight notebook computer is designed to provide years of reliable, high-performance computing. This manual tells how to set up and begin using your 2000 computer. It also provides detailed information on configuring your computer, basic operations and care, using optional devices and troubleshooting.
User's Manual Chapter 6, Power and Power-Up Modes, gives details on the computer’s power resources and battery save modes. Chapter 7, HW Setup and Passwords, explains how to configure the computer using the HW Setup program. It also tells how to set a password. Chapter 8, Optional Devices, describes the optional hardware available.
Conventions Key operation Some operations require you to simultaneously use two or more keys. We identify such operations by the key top symbols separated by a plus sign (+). For example, Ctrl + C means you must hold down Ctrl and at the same time press C. If three keys are used, hold down the first two and at the same time press the third.
User's Manual l
General Precautions Toshiba computers are designed to optimize safety, minimize strain and withstand the rigors of portability. However, certain precautions should be observed to further reduce the risk of personal injury or damage to the computer. Be certain to read the general precautions below and to note the cautions included in the text of the manual. Stress injury Carefully read the Instruction Manual for Safety & Comfort.
User's Manual lii
Introduction This chapter provides an equipment checklist, and it identifies the computer’s features, options and accessories. CAUTION: Some of the features described in this manual may not function properly if you use an operating system that was not preinstalled by TOSHIBA. Equipment checklist Carefully unpack your computer. Save the box and packing materials for future use.
INTRODUCTION User's Manual Windows® XP ❑ The following software is preinstalled: • • • • • • • • • • • • ❑ Documentation: • • • • ❑ Microsoft® Windows® XP Professional Modem driver Display Drivers for Windows TOSHIBA Utilities MouseWare Sound Driver DVD Video Player (Can be used only for DVD-ROM model) Easy CD Creator (Can be used only for CD-R/RW or CD-RW/DVD-ROM model) LAN Drivers TOSHIBA Power Saver TOSHIBA Console Online manual TE2000 Portable Personal Computer User’s Manual Microsoft® Windows®XP
Features ❑ INTRODUCTION • • • • • • LAN Drivers Infrared Device Driver Microsoft® Internet Explorer6.0 TOSHIBA Power Saver TOSHIBA Console Online manual Documentation: • Microsoft® Windows®2000 manual package • The same documentation that is supplied with Windows® XP Professional. If any of the items are missing or damaged, contact your dealer immediately.
INTRODUCTION User's Manual Memory Slots Level 2 cache 128 or 256 MB memory modules can be installed in the two memory slots for a maximum of 512 MB system memory. Provided to maximize performance. • Celeron™ : 128 KB • Pentium® III processor-M : 512 KB Video RAM 16 MB of RAM is provided for video display. Disks Hard disk drive The computer has an integrated, 2 1/2" hard disk drive (HDD) for nonvolatile storage of data and software. It comes in the following sizes.
Features Some models are equipped with a full-size, CD-R/RW drive module that lets you record CDs as well as run either digital versatile or compact disks without using an adaptor. It runs CDs and CD-Rs at maximum 24 speed and CDRWs at maximum 14 speed. It writes CD-Rs at maximum 8 speed and CD-RWs at maximum 8 speed.
INTRODUCTION User's Manual AccuPoint II Built-in A pointing device, the AccuPoint II, in the center of the keyboard and control buttons at the base of the keyboard enable control of the on-screen pointer and scrolling of windows. Power Battery pack The computer is powered by one rechargeable lithium-ion battery pack. RTC battery The internal RTC battery backs up the Real Time Clock (RTC) and calendar.
Features INTRODUCTION Slots PC card A PC card slot accommodates: Two 5 mm Type II One 10.5 mm Type III Refer to Chapter 8, Optional Devices, for details. Multimedia Sound System Sound Blaster™ Pro™ and Windows Sound System compatible sound system provides internal speaker as well as jacks for an external microphone and headphone. It also has a volume control dial. Video-out jack This RCA jack lets you transfer NTSC or PAL data to external devices.
INTRODUCTION User's Manual Slim Select Bay Modules Slim Select Bay is a single-drive bay that accommodates a CD-ROM drive, DVD-ROM drive, CD-R/RW drive, CDRW/DVD-ROM drive, secondary hard disk drive or secondary battery. The Slim Select Bay utility enables hot docking of modules when you are using a plug and play operating system.
Special features The following features are either unique to TOSHIBA computers or are advanced features, which make the computer more convenient to use. Hotkeys Key combinations let you quickly modify the system configuration directly from the keyboard without running a system configuration program. Keypad overlay Gray keys with gray lettering make up the keypad overlay, which lets you use the keyboard for ten-key operations or cursor control.
INTRODUCTION User's Manual Auto power on Standby Hibernation Heat dispersal This feature lets you set a time and date for the computer to turn on automatically. The feature is useful for receiving remote communications while you are asleep or away. You can specify the setting in Scheduled Tasks. If you have to interrupt your work, you can turn off the power without exiting from your software. Data is maintained in the computer’s main memory.
Utilities Supervisor Password Utility for Windows This Windows program lets you define your own “shortcut” keys to quickly launch applications and speed your work in Windows. To start the utility, click the Windows Start button, point to Programs (All Programs in Windows ® XP), point to TOSHIBA Utilities and click Fn-esse. This utility for Windows lets you register a Supervisor Password, which restricts access to set-up programs. You can also use it to modify the user password in Windows.
INTRODUCTION User's Manual Easy CD Creator This easy-to-use software lets you record CDs with just a few mouse clicks. You can create CDs in several formats including audio CDs that can be played on a standard stereo CD player and data CDs to store the files and folders on your hard drive. The CDs you create are accessible through a drive letter, just like a diskette drive. This software can be used only on models with CD-R/RW or CD-RW/DVD-ROM drives.
Options The following modules can be installed in the Slim Select Bay. The user can select either a CD-ROM drive, a DVD-ROM drive, a CD-R/CD-RW drive, a CD-RW/ DVD-ROM drive , a Slim Select Bay HDD adaptor or a Slim Select Bay 2nd battery pack to be preinstalled as a standard device. All other modules are options. CD-ROM Refer to the Features section for details. DVD-ROM Refer to the Features section for details. CD-R/RW Refer to the Features section for details.
INTRODUCTION User's Manual 1-14
Chapter 2 The Grand Tour Front with the display closed Figure 2-1 shows the computer’s front with its display panel in the closed position. DISPLAY LATCH INFRARED PORT MICROPHONE HEADPHONE Figure 2-1 Front of the computer with display closed Display latch This latch secures the LCD panel in its closed position. Slide the latch to open the display. Microphone jack A standard 3.5 mm mini microphone jack enables connection of a monaural microphone or other device for audio input.
THE GRAND TOUR Infrared port This infrared port is compatible with Infrared Data Association (IrDA 1.1) standards. It enables cableless 4 Mbps, 1.152 Mbps, 115.2 Kbps, 57.6 Kbps, 38.4 Kbps, 19.2 Kbps or 9.6 Kbps data transfer with IrDA 1.1 compatible external devices. Left side Figure 2-2 shows the computer’s left side.
Right side A CD-ROM drive, DVD-ROM drive, CD-R/RW drive, CD-RW/DVD-ROM drive, Slim Select Bay HDD adaptor, secondary battery pack can be installed in the Slim Select Bay. A weight saver can be installed when there is no module. Wireless communication switch Slide this switch toward the back of the computer to turn on Wireless LAN. Slide it toward the front of the computer to turn off the functions. On Off Volume control Use this dial to adjust the volume of the system speaker and headphones.
User's Manual Back side THE GRAND TOUR Figure 2-4 shows the computer’s back side. MODEM JACK LAN INDICATOR USB PORTS FAN VENT DC IN 15V EXTERNAL MONITOR PORT PARALLEL PORT LAN SERIAL PS/2 KEYBOARD/ JACK PORT MOUSE PORT Figure 2-4 The computer’s back side DC IN 15V DC IN 15V Fan vent The AC adaptor connects to this socket. Use only the model of AC adaptor that comes with the computer. Using the wrong adaptor can damage your computer. Provides air flow for the fan.
Underside LAN jack Ether LAN indicator This jack lets you connect to a LAN. The adaptor has built-in support for Ethernet LAN (10 megabits per second, 10BASE-T) and Fast Ethernet LAN (100 megabits per second, 100BASE-Tx). This indicator glows green when the computer is accessing the LAN. Use this 9-pin port to connect external serial devices such as an external modem, a serial mouse or printer.
User's Manual Docking port Use this port to connect an optional Port Replicator. THE GRAND TOUR CAUTION: Keep foreign objects out of the docking port. A pin or similar object can damage the computer’s circuitry. Docking holes Battery pack Battery pack lock Battery release latch These holes ensure a proper connection between the computer and an optional Port Replicator. The battery pack powers the computer when the AC adaptor is not connected.
Front with the display open Front with the display open Figure 2-6 shows the front of the computer with the display open. To open the display, slide the display latch on the front of the computer and lift the display up. Position the display at a comfortable viewing angle.
User's Manual AccuPoint II THE GRAND TOUR AccuPoint II control buttons Speaker Power source/ system indicators Sensor switch A pointer control device located in the center of the keyboard is used to control the on-screen pointer. Refer to the AccuPoint II section in Chapter 4, Operating Basics. Control buttons below the keyboard let you select menu items or manipulate text and graphics designated by the onscreen pointer.
Indicators Power source/system indicators DC IN Main battery Disk The Power indicator glows green when the computer is on. If you turn off the computer in Resume mode, this indicator blinks orange (one second on, two seconds off) while the computer shuts down. The Main battery indicator shows the condition of the charge. Green means fully charged and orange means being charged. Refer to Chapter 6, Power and Power-Up Modes. The Disk indicator glows green when the computer is accessing a disk drive.
User's Manual The figures below show the positions of the keypad overlay indicators and the CapsLock indicator. THE GRAND TOUR When the F10 key indicator glows the keypad overlay lets you enter numbers. When the F11 key indicator glows the keypad overlay lets you control the cursor. NUMERIC MODE ARROW MODE Figure 2-8 Keypad overlay indicators When the CapsLock indicator glows the keyboard is in all-caps mode.
Slim Select Bay modules Numeric mode You can use the keypad overlay (white labeled keys) for numeric input when the Numeric mode indicator lights green. Refer to the Keypad overlay section in Chapter 5, The Keyboard. The AC adaptor converts AC power to DC power and reduces the voltage supplied to the computer. It can automatically adjust to any voltage from 100 to 240 volts and to a frequency of either 50 or 60 hertz, enabling you to use the computer in almost any region.
User's Manual DVD-ROM drive THE GRAND TOUR An optional full-size DVD-ROM drive module lets you run either 12 cm (4.72") or 8 cm (3.15") digital video disk/compact disk without using an adaptor. It may be selected as a standard component or as an option. NOTE: The read speed is slower at the center of a disk and faster at the outer edge.
Slim Select Bay modules DVD-ROM drives and media are manufactured according to the specifications of six marketing regions. When you purchase DVD media, make sure it matches your drive, otherwise it will not play properly.
User's Manual CD, CD-R read 24 speed (maximum) CD-RW read 14 speed (maximum) CD-R write 8 speed (maximum) CD-RW write 8 speed (maximum) THE GRAND TOUR This drive supports the following formats: • • • • Photo CD CD-ROM CD-ROM x A CD-EXTRA • • • • CD-R CD-Rewritable CD-DA CD-Text NOTE: The physical features of this drive are similar to those of the DVD-ROM drive. Refer to the illustration in the DVD-ROM drive section. CAUTION: Check the Slim Select Bay indicator when you use the CDR/RW drive.
Slim Select Bay modules CAUTION: Check the Slim Select Bay indicator when you use the CDRW/DVD-ROM drive. Do not press the eject button, disconnect a drive or turn off the computer while the light is glowing. Doing so could damage the CD/DVD or the drive.
User's Manual Slim Select Bay 2nd battery pack THE GRAND TOUR An optional battery pack can be installed in the Slim Select Bay to increase the computer’s battery power and operating time. For details, refer to the documentation accompanying the secondary battery pack. Refer to Chapter 8, Optional Devices, for details on installing a Slim Select Bay 2nd battery pack.
Chapter 3 Getting Started This chapter provides basic information to get you started using your computer. It covers the following topics: ❑ Setting up your work space — for your health and safety NOTE: Be sure also to read Instruction Manual for Safety & Comfort. This guide, which is included with the computer, explains product liability.
User's Manual Setting up your work space GETTING STARTED Establishing a comfortable work site is important for you and your computer. A poor work environment or stressful work habits can result in discomfort or serious injury from repetitive strain to your hands, wrists or other joints. Proper ambient conditions should also be maintained for the computer’s operation.
❑ Place the computer so that it is directly in front of you when you work and make sure you have adequate space to easily operate other devices. ❑ Allow adequate space behind the computer to let you freely adjust the display. The display should be angled to reduce glare and maximize visibility. ❑ If you use a paper holder, set it at about the same height and distance as the computer.
User's Manual Lighting Proper lighting can improve legibility of the display and reduce eye strain. ❑ Position the computer so that sunlight or bright indoor lighting does not reflect off the screen. Use tinted windows, shades or other screen to eliminate sun glare. ❑ Avoid placing the computer in front of bright light that could shine directly in your eyes. ❑ If possible, use soft, indirect lighting in your computer work area.
Opening the display The display panel can be rotated in a wide range of angles for optimal viewing. 1. Slide the display latch on the front of the computer to the right to unlatch the display panel. 2. Lift the panel up and adjust it to the best viewing angle for you. NOTE: When you open the display, hold it with both hands and lift up slowly.
User's Manual 1. Connect the power cord to the AC adaptor. Figure 3-3 Connecting the power cord to the AC adaptor GETTING STARTED 2. Connect the AC adaptor’s DC output plug to the DC IN port on the back side of the computer. Figure 3-4 Connecting the adaptor to the computer 3. Plug the power cord into a live wall outlet. The Battery and DC IN indicator on the front of the computer should glow.
Turning on the power This section describes how to turn on the power. NOTE: After you turn on the power for the first time, do not turn it off until you have set up the operating system (OS) and the OS has started up. 1. If the external diskette drive is connected, make sure it is empty. If a diskette is in the drive, press the eject button and remove the diskette. 2. Open the display panel. GETTING STARTED 3. Press and hold the button for two or three seconds.6.
User's Manual Windows XP Professional/2000 setup When you first turn on the power, the computer’s initial screen is the Microsoft Windows XP Professional Startup Screen Logo. Follow the on-screen directions. If you ordered Windows 2000, the operating system is not preinstalled. Follow the steps below to install the Windows 2000 and TOSHIBA utilities. 1. Turn on the computer, load the Product Recovery CD-ROM in the drive and turn off the power. 2. Hold down the C key and turn on the power.
2. Make sure all disk activity has stopped, then remove any CDs or diskette. CAUTION: Make sure the Disk, Slim Select Bay and Slim Select Bay’s module indicators are off. If you turn off the power while a disk is being accessed, you can lose data or damage the disk. 3. If you are using Windows XP, click start then click Turn off computer. From the Turn off computer menu select Turn off. If you are using Windows 2000/98, click Start and click Shut Down. From the Shut Down menu select Shut Down. 4.
User's Manual ❑ You can return to your previous working environment immediately when you turn on the computer. ❑ Saves power by shutting down the system when the computer receives no input or hardware access for the duration set by the System hibernate feature. ❑ You can use the panel power off feature. Starting Hibernation To enter Hibernation mode, follow the steps below. Windows XP GETTING STARTED 1. Click Start. 2. Select Turn Off Computer. 3. Open the Turn Off Computer dialog box.
4. Select the Power Save Modes window. 5. Double-click Power Mode (Full Power, Normal, etc.) and open the System Power Mode window. 6. Enable the desired Hibernation settings for When I press the power button and When I close the lid. 7. Click the OK button. Data save in hibernation mode When you turn off the power in hibernation mode, the computer takes a moment to save current memory data to the hard disk. During this time, the Built-in HDD indicator will light.
User's Manual ❑ Restores the previous working environment more rapidly than does hibernation. ❑ Saves power by shutting down the system when the computer receives no input or hardware access for the duration set by the System Standby feature. ❑ You can use the panel power off feature. Executing standby You can enter standby mode in one of three ways: 1. In Windows XP, click Start, click Turn Off Computer and click Stand by.
❑ You change certain computer settings. ❑ An error occurs and the computer does not respond to your keyboard commands. There are three ways to restart the computer system: 1. If you are using Windows XP, click start then click Turn off computer. From the Turn off computer menu select Restart. If you are using Windows 2000/98, click Start and click Shut Down. From the Shut Down menu select Restart. 2. If the computer is already on, press Ctrl + Alt + Del (Windows 98 only). 3.
User's Manual similar to the one below will be shown while the software is being decompressed. Leave it until it disappears. Do not click Cancel. Figure 3-6 Software decompression window GETTING STARTED 3. 3-14 Follow the on-screen instructions.
GETTING STARTED 3-15
Chapter 4 Operating Basics This chapter gives information on basic operations including using the AccuPoint II, optical media drives, the external diskette drive, the internal modem, the LAN and changing Slim Select Bay modules. It also provides tips on caring for your computer and heat dispersal. Using AccuPoint II To use the AccuPoint II, simply push it with your finger tip in the direction you want to move the on-screen pointer.
User's Manual AccuPoint II precautions Certain conditions can affect the on-screen pointer when using AccuPoint II. For example, the pointer may travel contrary to AccuPoint II operation or an error message may appear, if ❑ ❑ ❑ ❑ You touch the AccuPoint II during power-up. You apply constant, soft pressure during power-up. There is a sudden temperature change. Strong stress is applied to the AccuPoint II. If an error message appears, reboot the computer.
Changing Slim Select Bay modules Changing Slim Select Bay modules This section explains how to change modules in the Slim Select Bay. The illustrations show replacement of the DVD-ROM drive with the Slim Select Bay HDD adaptor. Therefore, the text refers to those modules. However, the procedures are the same for any of the modules: DVD-ROM drive, CD-ROM drive, CD-R/RW drive, CD-RW/DVD-ROM drive or optional Slim Select Bay 2nd battery pack with separate tray.
User's Manual Installing a module Install the Slim Select Bay HDD adaptor as described below. 1. Insert the Slim Select Bay HDD adaptor in the computer as shown below and press until the ejector clicks. 2. If you want to lock the Slim Select Bay module, set the screw of the Slim Select Bay lock in the back hole.
Using optical media drives CD-R/RW drive Read CD, CD-R 24-speed (maximum) CD-RW 14-speed (maximum) Write CD-R 8-speed (maximum) CD-RW 8-speed (maximum) CD-RW/DVD-ROM drive Read CD 24-speed (maximum) DVD 8-speed (maximum) Write CD-R 8-speed (maximum) CD-RW 8-speed (maximum) Loading CDs OPERATING BASICS To load CDs, follow the steps below and refer to figures 4-5 to 4-9. 1. Turn on the power. 2. a.Press the eject button to open the drawer slightly.
User's Manual b. Pressing the eject button will not open the drawer when the computer’s power is off. If the power is off, you can open the drawer by inserting a slender object (about 1.5 cm) such as a straightened paper clip into the eject hole just to the right of the eject button. Figure 4-6 Manual release with the eject hole OPERATING BASICS 3. Grasp the drawer gently and pull until it is fully opened.
Using optical media drives 4. Lay the CD, label side up, in the drawer. NOTE: When the drawer is fully opened, the edge of the computer will extend slightly over the CD tray. Therefore, you will need to turn the CD at an angle when you place it in the tray. After seating the CD, however, make sure it lies flat, as shown in figure 4-8. CAUTIONS: 1. Do not touch the laser lens. Doing so could cause misalignment. 2. Be careful to keep foreign matter from entering the drive.
User's Manual 6. Push the center of the drawer to close it. Press gently until it locks into place. CAUTION: If the CD is not seated properly when the drawer is closed, the CD might be damaged. Also, the drawer might not open fully when you press the eject button. OPERATING BASICS Figure 4-9 Closing the drawer Removing CDs To remove the CD, follow the steps below and refer to figure 4-10. CAUTION: Do not press the eject button while the computer is accessing the CD-ROM drive.
Using optical media drives 2. There are indentations on the sides of the drawer to let you grasp the CD. Hold it gently and lift it out. NOTE: When the drawer is fully opened, the edge of the computer will extend slightly over the CD tray. Therefore, you will need to turn the CD at an angle when you remove it. 3. Push the center of the drawer to close it. Press gently until it locks into place. CD/DVDs care Handle your media with care.
User's Manual 5. Do not expose to direct sunlight, extreme heat or cold. Do not place heavy objects on your CD/DVDs. 6. If your CD/DVDs become dusty or dirty, wipe them with a clean dry cloth. Wipe from the center out, do not wipe in a circular direction around the CD/ DVD. If necessary, use a cloth dampened in water or a neutral cleaner. Do not use benzine, thinner or similar cleaner. Using 3 1/2" external diskette drive An optional 3 1/2" external diskette drive module connects to the USB port.
Using 3 1/2" external diskette drive NOTES: 1. The external diskette drive should be placed on a flat, horizontal surface when in use. Do not set the drive on an incline greater than 20o while it is operating. 2. Do not set anything on top of the diskette drive. 3. If you need to boot the computer from the diskette drive or if you use an OS that does not support USB, you must set the USB-FDD Legacy Emulation feature in HW Setup to Enabled. Refer to the USB section in Chapter 7.
User's Manual Disconnecting 3 1/2" diskette drive When you have finished using the diskette drive, follow the procedures below to disconnect it: 1. Wait for the indicator light to go out to make sure all diskette activity has stopped. CAUTION: If you disconnect the diskette drive or turn off the power while the computer is accessing the drive you may lose data or damage the diskette or the drive. 2. Pull the diskette drive connector out of the USB port. Diskette care Handle your diskettes with care.
Wireless communications Wireless communications Wireless LAN The wireless LAN is compatible with other LAN systems based on Direct Sequence Spread Spectrum radio technology that complies with IEEE 802.11 wireless LAN standard (Revision B). It supports the following features: ❑ Automatic Transmit Rate Select mechanism in the transmit range of 11, 5.5, 2 and 1 Mbit/s. ❑ Frequency Channel Selection (2.
User's Manual Wireless communication LED The LED indicates the status of the wireless communication functions. LED status Indication LED off Wireless communication switch is set to off. Automatic power down because of overheating. Power malfunction LED glows Wireless communication switch is on. Wireless LAN is turned on by an application. OPERATING BASICS If you used the Task Tray icon to disable W-LAN, restart the computer or follow the procedures below to enable the system to recognize W-LAN.
LAN LAN LAN circuits support Ethernet LAN (10 megabits per second, 10BASE-T) and Fast Ethernet LAN (100 megabits per second, 100BASE-Tx). This section describes how to connect/disconnect to a LAN. CAUTION: Do not install or remove an optional memory module while Wake-up on LAN is enabled. NOTE: Wake-up on LAN does not work without the AC adaptor. Leave it connected, if you are using this feature. LAN cable types CAUTION: The computer must be configured properly before connecting to a LAN.
User's Manual Using the internal modem 2. Plug one end of the cable into the LAN’s jack. Press gently until you hear the latch click into place. Figure 4-13 Connecting the LAN cable 3. Plug the other end of the cable into a LAN hub connector. Check with your LAN administrator before connecting to a hub. Disconnecting cable To disconnect the LAN cable, follow the steps below. OPERATING BASICS 1. Pinch the lever on the connector in the computer and pull out the connector. 2.
LAN Figure 4-14 The Super Long Life Properties window Network Device Switch This feature lets you select actions that will enable or disable LAN and wireless LAN functions. The following settings can be made in NetworkDeviceSwitch utility. To make settings follow the steps below. 1. Click the NetworkDeviceSwitch icon. The icon is on the Task bar. 2. Select a device or select Disable all device.
User's Manual Using the internal modem Depending on the settings in the TOSHIBA Power Saver utility, the following four events can trigger a change in the Power Savings settings. To avoid these automatic changes, clear the Control device power management checkbox in the Power Saver utility. For details, refer to the Power Saver utility’s help files. 1. You start the computer on battery power. 2. You start the computer with the AC adapter connected and disconnect the AC adapter during operation. 3.
Using the internal modem 2. The Region Selection icon will appear in the Windows Task Bar. Figure 4-14 The Region Selection icon (Windows® XP) Figure 4-15 The Region Selection icon (Windows® 2000) 3. Click the icon with the primary mouse button to display a list of regions that the modem supports. A sub menu for telephony location information will also be displayed. A check will appear next to the currently selected region and telephony location. 4.
User's Manual Cleaning the computer Figure 4-17 The menu list (Windows® 2000) Setting You can enable or disable the following settings: AutoRun Mode Region Select Utility starts automatically when you start up the operating system. Open the Dialing Properties dialog box after selecting region. OPERATING BASICS The dialing properties dialog box will be displayed automatically after you select the region. Location list for region selection. A submenu appears displaying location information for telephony.
Using the internal modem Dialing Properties Select this item to display the dialing properties. CAUTION: If you are using the computer in Japan, technical regulations described in the Telecommunications Business Law require that you select Japan region mode. It is illegal to use the modem in Japan with any other selection. Connecting To connect the internal modem cable, follow the steps below. CAUTIONS: 1. In case of a lightning storm, unplug the modem cable from the telephone jack. 2.
User's Manual Disconnecting To disconnect the internal modem cable, follow the steps below. 1. Pinch the lever on the connector in the telephone jack and pull out the connector. 2. Disconnect the cable from the computer in the same manner. 3. In the same way, pull the cable’s other connector out of the computer. Cleaning the computer OPERATING BASICS To help ensure long, trouble-free operation, keep the computer free of dust and use care with liquids around the computer.
Heat dispersal ❑ Close the display. Do not pick up the computer by its display panel or back (where the interface ports are located). ❑ ❑ Close all port covers. Use the carrying case when transporting the computer. Heat dispersal To protect from overheating, the CPU has an internal temperature sensor. If the computer’s internal temperature rises to a certain level, the cooling fan is turned on or the processing speed is lowered.
OPERATING BASICS User's Manual 4-24
Chapter 5 The Keyboard The computer’s keyboard layouts are compatible with a 101/102-key enhanced keyboard. By pressing some keys in combination, all the 101/102-key keyboard functions can be executed on the computer. The number of keys on your keyboard depends on which country/region’s keyboard layout your computer is configured with. Keyboards for numerous languages are available. There are five types of keys: typewriter keys, keypad overlay, function keys, soft keys and cursor control keys.
User's Manual F1 … F12 function keys The function keys, not to be confused with Fn, are the 12 keys at the top of your keyboard. These keys are dark gray, but function differently from the other dark gray keys. F1 through F12 are called function keys because they execute programmed functions when pressed. Used in combination with the Fn key, keys marked with icons execute specific functions on the computer. See the section, Soft keys: Fn key combinations, in this chapter.
Soft keys: Fn key combinations The keyboard is designed to provide all the features of the 101-key enhanced keyboard, shown in figure 5-1. The 101/102-key enhanced keyboard has a numeric keypad and scroll lock key. It also has additional Enter, Ctrl and Alt keys to the right of the main keyboard. Since the keyboard is smaller and has fewer keys, some of the enhanced keyboard functions must be simulated using two keys instead of one on the larger keyboard.
User's Manual Hotkeys Hotkeys (Fn + a function or Esc key) let you enable or disable certain features of the computers. Sound mute: Pressing Fn + Esc in a Windows environment turns sound on or off. When you press these hotkeys, the current setting will be displayed as an icon. Instant security: Press Fn + F1 to lock the keyboard and blank the screen to prevent others from accessing your data. To restore the screen and original settings, press any key or move the AccuPoint II.
Soft keys: Fn key combinations Hibernation: Press Fn + F4 to turn Hibernation mode on and off. When you press these hotkeys, the current setting will be displayed in a dialog box that will let you OK or cancel the displayed setting. A check box lets you select whether to hide or display the dialog box. When you turn on Hibernation, Standby will be automatically turned off, if it is enabled. Display selection: Press Fn + F5 to change the active display device.
User's Manual Wireless setting: Non functioning key combination. Emulating Fn key on external keyboard The Fn key is only on Toshiba keyboards. If you use an external keyboard attached to the computer, you can execute Fn key combinations by emulating the Fn key. See Chapter 7, HW Setup and Passwords, for details on setting the Fn key equivalent.
Keypad overlay Turning on the overlays The numeric keypad overlay can be used for numeric data input or cursor and page control. Arrow mode To turn on the Arrow mode, press Fn + F10. The Arrow mode indicator lights. Now try cursor and page control using the keys shown in figure 5-2. Press Fn + F10 again to turn off the overlay. Numeric mode To turn on the Numeric mode, press Fn + F11. The Numeric mode indicator lights. Now try numeric data entry using the keys in figure 5-2.
User's Manual Temporarily using normal keyboard (overlay on) While using the overlay, you can temporarily access the normal keyboard without turning off the overlay: 1. Hold Fn and press any other key. All keys will operate as if the overlay were off. 2. Type uppercase characters by holding Fn + Shift and pressing a character key. 3. Release Fn to continue using the overlay.
Generating ASCII characters Generating ASCII characters Not all ASCII characters can be generated using normal keyboard operation. But, you can generate these characters using their ASCII codes. With the overlay on: 1. Hold down Alt. 2. Using the overlay keys, type the ASCII code. 3. Release Alt, and the ASCII character appears on the display screen. With the overlay off: 1. Hold Alt + Fn. 2. Using the overlay keys, type the ASCII code. 3.
THE KEYBOARD User's Manual 5-10
Power and Power-Up Modes The computer’s power resources include the AC adaptor and internal batteries. This chapter gives details on making the most effective use of these resources including charging and changing batteries, tips for saving battery power, and power up modes. Power conditions The computer’s operating capability and battery charge status are affected by the power conditions: whether an AC adaptor is connected, whether a battery is installed and what the charge level is for the battery.
POWER AND POWER-UP MODES User's Manual Table 6-1 Power conditions continued Power on Power off (no operation) AC 2nd battery • Operates adaptor fully • LED: 2nd battery green connected charged 2nd battery • LED: 2nd battery green • Quick charge *2 • Operates 2 partially • Quick charge * charged • LED: 2nd battery orange or no charge • LED: 2nd battery orange DC IN green DC IN green No • Operates • No charge 2nd battery • No charge • LED: 2nd battery off installed • LED: 2nd batt
Power conditions Power on AC 2nd battery • Operates adaptor charge • LED: 2nd battery off not is above Power off (no operation) DC IN off connected low battery trigger point 2nd battery • Operates charge • LED: 2nd battery is below flash orange low battery DC IN off trigger point 2nd battery Computer goes charge is into resume mode exhausted and shuts down *3 No • No operation *5 2nd battery • LED: 2nd battery off is installed DC IN off NOTE: 2nd battery indicator refers to th
POWER AND POWER-UP MODES User's Manual Power indicators The Main battery, Slim Select Bay, DC IN and Power indicators on the system indicator panel alert you to the computer’s operating capability and battery charge status. Battery indicators Check the Main battery indicator to determine the status of the main battery and the Slim Select Bay indicator to determine the status of the secondary battery. The following indicator lights indicate the battery status: Flashing orange The battery charge is low.
Battery types Check the Power indicator to determine the power status. Green Blinking orange No light Indicates power is being supplied to the computer and the computer is turned on. Indicates the power was turned off while the computer was in Resume mode. The indicator turns on for one second and turns off for two seconds. Under any other conditions, the indicator does not light.
POWER AND POWER-UP MODES User's Manual Secondary battery (option) An optional secondary battery can be installed in the Slim Select Bay to increase your battery operating time. Note the caution on Resume mode in the previous section Main battery. CAUTION: The secondary battery pack is a lithium ion battery, which can explode if not properly replaced, used, handled or disposed of. Dispose of the battery as required by local ordinances or regulations.
Care and use of the battery pack The battery pack is a vital component of portable computing. Taking proper care of it will help ensure longer operating time on battery power as well as a longer life for your battery pack. Follow the instructions in this section carefully to ensure safe operation and maximum performance. Safety precautions 1. Be very careful not to short-circuit the battery pack. Contacting both terminals with a metal object can cause injury, fire or damage to the battery pack. 2.
POWER AND POWER-UP MODES User's Manual Charging the batteries When the power in the battery pack becomes low, the Battery indicator flashes orange indicating that only a few minutes of battery power remain. If you continue to use the computer while the Battery indicator flashes, the computer enables Resume mode (so you don’t lose data) and automatically turns off. You must recharge a battery pack when it becomes discharged.
Care and use of the battery pack ❑ The battery has not been used for a long time. ❑ The battery has completely discharged and been left in the computer for a long time. ❑ A cool battery is installed in a warm computer. In such case, follow the steps below. 1. Fully discharge the battery by leaving it in the computer with the power on until the power automatically shuts off. 2. Plug in the AC adaptor. 3. Charge the battery until the Battery indicator glows green.
POWER AND POWER-UP MODES User's Manual Maximizing battery operating time A battery’s usefulness depends on how long it can supply power on a single charge. How long the charge lasts in a battery depends on: ❑ How you configure the computer, for example, whether you enable batterypower saving options. The computer provides a battery save mode to conserve battery power.
Care and use of the battery pack To maximize the life of your battery pack: ❑ At least once a month, disconnect the computer from a power source and operate it on battery power until the battery pack fully discharges. Before doing so, follow the steps below. 1. Turn off the computer’s power. 2. Disconnect the AC adaptor and turn on the computer’s power. If it does not turn on go to step 4. 3. Operate the computer on battery power for five minutes.
POWER AND POWER-UP MODES User's Manual Replacing the battery pack When the battery pack reaches the end of its operating life you will need to install a new one. The life of the battery pack is generally about 500 recharges. If the Battery indicator flashes orange shortly after fully recharging the battery, the battery pack needs to be replaced. You might also replace a discharged battery pack with a charged spare when you are operating your computer away from an AC power source.
Replacing the battery pack POWER AND POWER-UP MODES BATTERY PACK LOCK BATTERY PACK BATTERY RELEASE LATCH Figure 6-1 Removing the battery pack Installing the battery pack To install a battery pack, follow the steps below. CAUTION: The battery pack is a lithium ion battery, which can explode if not properly replaced, used, handled or disposed of. Dispose of the battery as required by local ordinances or regulations. Use only batteries recommended by TOSHIBA as replacements. 1.
POWER AND POWER-UP MODES User's Manual 2. Insert the battery pack. BATTERY PACK Figure 6-2 Installing the battery pack 3. Secure the battery pack lock. Starting the computer by password If you registered a password as supervisor or user, you must enter it to start the computer. For more information about how to set a password, refer to Chapter 7, HW Setup and Passwords. To start up the computer with the password, follow these steps: 1.
Chapter 7 HW Setup and Passwords HW Setup TOSHIBA HW Setup lets you configure settings for pointing devices, display, CPU, boot priority, keyboard, USB, LAN, general, password, device config and parallel/printer. NOTE: If the supervisor password is set, access to the TOSHIBA HW Setup program can be prevented when the user password is used to log on to the computer. Refer to the Supervisor password readme file for details on enabling/ disabling access to HW Setup.
User's Manual HW Setup window HW SETUP AND PASSWORDS The HW Setup window contains the following tabs: Pointing Devices, Display, CPU, Boot Priority, Keyboard, USB, LAN, General, Password, Device Config and Parallel/Printer.
HW Setup HW SETUP AND PASSWORDS Figure 7-2 HW setup window (Windows® 2000) There are also three buttons: OK, Cancel and Apply. OK Cancel Apply Accepts your changes and closes the HW Setup window. Closes the window without accepting your changes. Accepts all your changes without closing the HW Setup window.
User's Manual General This window displays the BIOS version and contains two buttons: Default and About. Default Return all HW Setup values to the factory settings. HW SETUP AND PASSWORDS About Display the HW Setup version.. Setup This field displays BIOS Version and date. Password User Password This option allows you to set or reset the user password for power on. Not Registered Registered Change or remove the password. (Default) Set the password.
HW Setup To delete a user password: 1. Select Not Registered to display the following prompt: Enter Password: 2. Enter the currently registered password. The character string you enter is displayed as a string of asterisks. Enter Password: **** 3. Click the OK button. If the character string you enter matches the registered password, the password option is reset and the display changes to: Not registered If they do not match, the following message appears. You must repeat step 1.
User's Manual Parallel/Printer This tab lets you set the Printer Port Type. Use the Windows Device Manager to make settings for the Parallel port. Parallel Port Mode HW SETUP AND PASSWORDS The options in this tab are ECP and Standard Bi-directional. ECP Sets the port type to Extended Capabilities Port (ECP). For most printers, the port should be set to ECP. (Default) Standard Bi-directional This setting should be used with some other parallel devices.
HW Setup CPU NOTE: This feature appears only on computers with Mobile Intel® Pentium® III processor-M. Dynamic CPU Frequency Mode This option lets you choose from the following settings: CPU power consumption and clock speed automatic switching function is enabled. When the computer is in use, CPU operation is automatically switched when necessary. (Default) Always High CPU power consumption and clock speed automatic switching function is disabled. The CPU always runs at its fastest speed.
User's Manual CD-ROM −> LAN −> HDD −> FDDThe computer looks for bootable files in the following order: CD-ROM*, LAN, HDD, diskette drive. HW SETUP AND PASSWORDS CD-ROM −> LAN −> FDD −> HDDThe computer looks for bootable files in the following order: CD-ROM*, LAN, diskette drive and HDD. You can override the settings and manually select a boot device by pressing one of the following keys while the computer is booting: U Selects the USB diskette drive. N Selects the Network. 1 Selects the primary HDD.
HW Setup 2. The following menu will be displayed: Select Boot Device [C]: CD-ROM [N]: Network (LAN) [U]: USB Floppy Drive [1]: Primary Hard Drive (Built-in) HW SETUP AND PASSWORDS [2]: Secondary Hard Drive (Select Bay) [P]: PC Card Drive Hard Drive [D]: Default SYSTEM SETUP Device Press [C], [N], [U], [1], [2], [P] or [D] NOTES: 1. If a supervisor password is set, the menu above does not appear when you use the user password to start the computer. 2.
User's Manual Keyboard External Keyboard Fn key HW SETUP AND PASSWORDS Use this option to set a key combination on an external keyboard to emulate the Fn key on the computer’s internal keyboard. Setting an Fn key equivalent will let you use “Hotkeys” by pressing the set combination instead of the Fn key.
Supervisor password LAN Wake-up on LAN This features lets the computer’s power be turned on when it receives a wake-up signal from the LAN. Enabled Disabled Enables Wake-up on LAN. CAUTION: Do not install or remove an optional memory module while Wake-up on LAN is enabled. NOTE: Wake-up on LAN does not work without the AC adaptor. Leave it connected, if you are using this feature. Built-in LAN Enabled Disabled Enables built-in LAN functions. (Default) Disables built-in LAN functions.
HW SETUP AND PASSWORDS User's Manual 7-12
Chapter 8 Optional Devices Optional devices can expand the computer’s capabilities and its versatility.
User’s Manual PC cards The computer is equipped with a PC card expansion slot that can accommodate two 5 mm Type II cards or one 10.5 mm Type III card. Any PC card that meets industry standards (manufactured by TOSHIBA or other vendor) can be installed. The slots support 16-bit PC cards, including PC card 16’s multifunction card and CardBus PC cards. CardBus supports the new standard of 32-bit PC cards. The bus provides superior performance for the greater demands of multimedia data transmission.
PC cards 3. Check the configuration in the HW Setup window to make sure it is appropriate for your card. 4. Slide the PC card lock into the locked position. PC CARD LOCK OPTIONAL DEVICES Figure 8-2 Locking the PC card Removing a PC card To remove the PC card, follow the steps below. 1. Slide the PC card lock into the unlocked position. 2. a. In Windows® XP, open the Safety Remove Hardware icon on the system tray and disable the PC card. b.
User’s Manual PC CARD EJECT BUTTON OPTIONAL DEVICES Figure 8-3 Removing the PC card Memory expansion You can install additional memory in the computer’s memory module to increase the amount of RAM. 128,256 or 512MB memory modules can be installed in the two memory slots for a maximum of 1GB system memory.
Memory expansion 2. If you install a memory module that is not compatible with the computer, a beep will sound when you turn on the power. If the module is installed in slot A, there will be a long beep followed by a short beep. If the module is in slot B, there will be a long beep followed by two short beeps. In this case shut down the power and remove the incompatible module. 2. Remove all cables connected to the computer. 3.
OPTIONAL DEVICES User’s Manual Figure 8-7 Inserting the memory module 8. Seat the cover and secure it with two screws. 9. When you turn the computer on, it should automatically recognize the total memory capacity. Use the HW Setup program to verify that the added memory is recognized. If it is not recognized, check the module’s connection. Removing memory module To remove the memory module, make sure the computer is in boot mode then: 1.
Slim Select Bay 2nd battery pack LATCHES SLOT A SLOT B OPTIONAL DEVICES Figure 8-8 Removing the memory module 7. Seat the cover and secure it with two screws. CAUTION: If only one memory module is installed, use slot A. Do not try to operate the computer with a module installed in slot B only. Additional battery pack You can increase the portability of the computer with additional battery packs (PA3128*). If you’re away from an AC power source, you can replace a low battery with a fully charged one.
User’s Manual Installing To install the secondary battery pack in the adaptor, follow the steps below. 1. Fit the side of the secondary battery pack opposite the connector into the adaptor. OPTIONAL DEVICES 2. Lay the battery into the adaptor. The latch should close automatically to secure the secondary battery pack. Figure 8-9 Installing the secondary battery pack in the adaptor Removing To remove the secondary battery from the adaptor, follow the steps below. 1.
Slim Select Bay HDD adaptor Additional AC adaptor If you frequently transport the computer between different sites such as your home and office, purchasing an AC adaptor for each location will reduce the weight and bulk of your carrying load: PA3083*. Battery charger The battery charger (PA3091*) provides a convenient way to charge battery packs without requiring the use of your computer. The battery charger holds up to two Lithium-ion battery packs, which it charges one after the other in succession.
User’s Manual OPTIONAL DEVICES 2. Insert the HDD and push forward to ensure a firm connection. Figure 8-12 Installing the HDD 3. Close the lid and slide the lock to the lock position. Figure 8-13 Closing the lid For details on installing the Slim Select Bay HDD adaptor in the Slim Select Bay, refer to Chapter 4, Operating Basics.
Advanced Port Replicator USB diskette drive The 3 1/2" external diskette drive module can be connected to the USB port. For details on connecting the 3 1/2" external diskette drive module, refer to Chapter 4, Operating Basics. Advanced Port Replicator In addition to the ports available on the computer, the Port Replicator provides, audio line-out jack, line-in jack and separate ports for PS/2 mouse and PS/2 keyboard.
User’s Manual Parallel printer You can connect any standard Centronics-compatible parallel printer to your computer. All you need is an IBM PC™ parallel printer cable. Your dealer can supply one or you can purchase one at most computer stores. The cable’s connectors are designed so that it is impossible for you to connect them incorrectly. You can also connect a parallel printer to an optional Advanced Port Replicator. To connect a printer, follow these steps: 1. Turn off the computer. 2.
External monitor External monitor An external analog monitor can be connected to the external monitor port on the computer, Port Replicator. The computer supports VGA and Super VGA video modes. To connect a monitor, follow the steps below. CAUTION: If an external monitor is connected to the computer, do not connect the Port Replicator. First disconnect the external monitor from the computer then connect the Port Replicator and use its external monitor port.
User’s Manual Television A television can be connected to the video out port on the computer. To connect a television, follow the steps below. 1. Turn the computer off. OPTIONAL DEVICES 2. Use a video cable (not supplied) to connect the television to the video out port. Figure 8-14 Connecting a television 3. Turn the television on. 4. Turn the computer on. PS/2 mouse Use the PS/2 keyboard/mouse port on the computer or optional Advanced Port Replicator to connect a PS/2 mouse.
PS/2 keyboard 1. Turn the computer off. 2. Connect the PS/2 mouse to the PS/2 keyboard/mouse port on the computer or the mouse port on the optional Advanced Port Replicator, pressing gently to assure a firm connection. 3. Turn on the computer. To disconnect the mouse, turn off the computer and pull out the mouse connector. Consult your mouse manual for instructions on how to install necessary software.
User’s Manual Security lock A security lock enables you to anchor your computer to a desk or other heavy object to help prevent unauthorized removal of the computer. OPTIONAL DEVICES Attach one end of a cable to the desk and the other end to the security lock slot on the left side of the computer.
Chapter 9 Troubleshooting TOSHIBA designed the computer for durability. However, should problems occur, following the procedures in this chapter can help to determine the cause. All readers should become familiar with this chapter. Knowing what might go wrong can help prevent problems from occurring. Problem solving process Resolving problems will be much easier if you observe the following guidelines: ❑ Stop immediately when you recognize a problem exists.
User's Manual ❑ Check that your diskette is correctly inserted and that the diskette’s write protect tab is correctly set. Make notes of your observations and keep them in a permanent error log. This will help you describe your problems to your dealer. If a problem recurs, the log will help you identify the problem faster. Analyzing the problem TROUBLESHOOTING Sometimes the system gives clues that can help you identify why it is malfunctioning.
Hardware and system checklist Hardware and system checklist This section discusses problems caused by your computer’s hardware or attached peripherals.
User's Manual Self test When the computer starts up, the self-test will be run automatically, and the following will be displayed: In Touch with Tomorrow TOSHIBA This message remains on the screen for a few seconds. If the self test is successful, the computer tries to load the operating system. Depending on how the Boot Priority is set in the Hardware Setup or TSETUP program, the computer tries to load first from drive A then from drive C, or first from drive C then from drive A.
Hardware and system checklist Overheating power down If the computer’s internal temperature becomes too high, the computer will automatically enter Hibernation or Resume mode and shut down. Problem Procedure Computer shuts down and DC IN indicator blinks orange Leave the computer off until the DC IN indicator stops blinking. NOTE: It is recommended to leave the computer off until the its interior reaches room temperature even though the DC IN indicator stops blinking.
User's Manual Check the condition of the cord and terminals. If the cord is frayed or damaged, replace it. If the terminals are soiled, wipe them with cotton or a clean cloth. If the AC adaptor still does not power the computer, contact your dealer. Battery TROUBLESHOOTING If you suspect a problem with the battery, check the DC IN indicator as well as the Main battery and Slim Select Bay indicators. For information on indicators and battery operation see Chapter 6, Power and Power-Up Modes.
Hardware and system checklist Unplug the AC adaptor and remove the battery to make sure the terminals are clean. If necessary wipe them with a soft dry cloth dipped in alcohol. Connect the AC adaptor and replace the battery. Make sure it is securely seated. Check the Battery indicator. If it does not glow, let the computer charge the battery for at least 20 minutes.
User's Manual Keyboard Keyboard problems can be caused by your setup configuration. For more information refer to Chapter 5, The Keyboard and Chapter 7, HW Setup and Passwords. Problem Procedure Some letter keys produce numbers Check that the numeric keypad overlay is not selected. Press Fn + F10 and try typing again. Output to screen is garbled Make sure the software you are using is not remapping the keyboard. Remapping involves reassigning the meaning of each key.
Hardware and system checklist Hard disk drive Problem Procedure Computer does not boot from hard disk drive Check if a diskette is in the diskette drive. If a diskette is inserted, remove it and reboot. There may be a problem with your operating system files. Refer to your OS documentation. Slow performance Your files may be fragmented. Run SCANDISK and defragmenter to check the condition of your files and disk.
User's Manual A foreign object in the drawer could block laser light from reading the CD. Make sure there is no obstruction. Remove any foreign object. Check whether the CD is dirty. If necessary, wipe it with a clean cloth dipped in water or a neutral cleaner. See the CD/DVDs care section in Chapter 4 for details on cleaning. Check your config.sys and autoexec.bat files to make sure they have the necessary drivers and execution lines.
Hardware and system checklist A foreign object in the drawer could block laser light from reading the CD. Make sure there is no obstruction. Remove any foreign object. Check whether the CD is dirty. If necessary, wipe it with a clean cloth dipped in water or a neutral cleaner. See the CD/DVDs care section in Chapter 4 for details on cleaning. Check your config.sys and autoexec.bat files to make sure they have the necessary drivers and execution lines.
User's Manual A foreign object in the drawer could block laser light from reading the DVD. Make sure there is no obstruction. Remove any foreign object. Check whether the DVD is dirty. If it is, wipe it with a clean cloth dipped in water or a neutral cleaner. See the CD/DVDs care section in Chapter 4, Operating Basics, for details on cleaning. Check the Slim Select Bay lock on the bottom of the computer. It should be in the lock position.
Hardware and system checklist DVD does not play correctly in an optional Expansion Station Some video discs might not play properly in a Expansion Station. Play the disc in the DVD-ROM drive installed in the computer. If problems persist, contact your dealer. CD-RW/DVD-ROM drive For more information, refer to Chapter 4, Operating Basics. Problem Procedure You cannot access a CD or DVD in the drive Make sure the drive’s drawer is securely closed. Press gently until it clicks into place.
User's Manual Check the type of DVD/CD you are using. The drive supports: DVD-ROM: DVD-ROM, DVD-Video CD-ROM: Audio CD, Photo CD, ISO 9660, CD-EXTRA, CD-R, CD-Rewritable Check the region code on the DVD. It must match that on the DVD drive. Region codes are listed in the DVD-ROM drive section in Chapter 2, The Grand Tour. If problems persist, contact your dealer. Diskette drive TROUBLESHOOTING For more information, refer to Chapter 4, Operating Basics.
Hardware and system checklist Infrared port Refer also to the documentation for your IrDA compatible device and related software. Problem Procedure Infrared devices do not work as expected Check that the device is connected to an electric outlet. Make sure the outlet is supplying power by plugging in an appliance. Make sure there is no obstruction blocking communication between the computer and the target device. If problems persist, contact your dealer.
User's Manual Make sure your software is configured to recognize the printer. Check your printer and software documentation. Printer error Check your printer documentation. If problems persist, contact your dealer. Pointing device If you are using a PS/2 or serial mouse, also refer to Chapter 8, Optional Devices, and to your mouse documentation.
Hardware and system checklist Is your software configured to recognize the mouse? Check the software documentation. If problems persist, contact your dealer. Serial mouse Problem Procedure On-screen pointer Check for a firm connection between the does not respond to computer’s serial port and the cable’s 9-pin serial mouse operation connector. Did you connect the mouse before turning on the computer? Is your software configured to recognize the mouse? Check the software documentation.
User's Manual Monitor Refer also to Chapter 8, Optional Devices, and to your monitor’s documentation. Problem Procedure Monitor does not turn on Make sure that the external monitor’s power switch is on. Confirm that the external monitor’s power cable is plugged into a working power outlet. No display Try adjusting the contrast and brightness controls on the external monitor. Press hotkeys Fn + F5 to change the display priority and make sure it is not set for the internal display.
Hardware and system checklist Sound system Problem Procedure No sound is heard Adjust the volume control dial. Check the software volume settings. Make sure the headphone connection is secure. Check Windows Device Manager. Make sure the sound function is enabled and that settings for I/O address, Interrupt level and DMA are correct for your software and do not conflict with other hardware devices that you may have connected to the computer. If problems persist, contact your dealer.
User's Manual Press hotkeys Fn + F5 to change the display. Refer to Chapter 5, Keyboard. NOTE: If you turn the computer off in Resume mode while the display is on TV, the computer will select either the internal LCD or an external computer CRT as the display device. If problems persist, contact your dealer. USB Refer also to your USB device’s documentation. Problem Procedure USB device does not work Check for a firm cable connection between the USB ports on the computer and the USB device.
Hardware and system checklist Modem Refer to the online help files for Appendix C and D. Problem Procedure Communication software can't initialize modem Make sure the computer’s internal modem settings are correct. Refer to Phone and Modem Options in the Control Panel. You can hear a dial tone but can't make a call If the call is going through a PBX machine, make sure the communication application’s tone dial detection feature is disabled. You can also use the ATX command.
User's Manual A CONNECT display is quickly replaced by NO CARRIER Check the error control setting in your communications application. You can also use the AT\N command. Refer to the chapter on AT commands in online help files for Appendix C, AT Commands. Character display becomes garbled during a communication In data transmission, make sure the parity bit and stop bit settings correspond with those of the remote computer. Check the flow control and communication protocol.
Hardware and system checklist Memory expansion Refer also to Chapter 8, Optional Devices, for information on installing memory modules. Problem Procedure Beep sounds. (If slot A two beeps, If slot B three beeps, If both two and three beeps) Make sure the memory module installed in the expansion slot is compatible with the computer. If an incompatible module has been installed, follow the steps below. 1. Disconnect the AC adaptor and all peripheral devices. 2. Remove the battery pack. 3.
User's Manual Wireless LAN If the following procedures do not restore LAN access, consult your LAN administrator. For more information on wireless communication, refer to Chapter 4, Operating Basics. Problem Procedure Cannot access Wireless LAN Make sure the computer’s wireless communication switch is set to on. If problems persist, consult your LAN administrator.
TOSHIBA support Outside of Europe Australia TOSHIBA Australia Pty. Ltd. Information Systems Division 84-92 Talavera Road North Ryde N.S.W. 2113 Sydney Canada TOSHIBA of Canada Ltd. 191 McNabb Street, Markham, Ontario L3R 8H2 Singapore TOSHIBA Singapore Pte. Ltd. 438B Alexandra Road #06-01 Alexandra Technopark Singapore 119968 USA In Europe Germany & Austria TOSHIBA Europe (I.E.) GmbH Geschäftsbereich, Deutschland-Österreich Hammfelddamm 8, D-41460 Neuss, Germany France TOSHIBA Systèms France S.A.
TROUBLESHOOTING User's Manual 9-26
Specifications This appendix summarizes the computer’s technical specifications. Physical Dimensions Size With TFT display 316 (w) x 275 (d) x 33.9/38.1 (h) millimeters (does not include the thicker part of the bottom of the computer) Weight CD/DVD Display Kilograms DVD-ROM 14" XGA-TFT 2.6 kg typical* ( WEIGHT SAVER 14" XGA-TFT 2.4 kg typical ) * Weight will vary depending on whether or not and what kind of options are adopted.
User's Manual APPENDIX A 50 or 60 hertz (cycles per second) Computer 15 VDC 5.0 amperes Built-in Modem Network control unit (NCU) Type of NCU Type of line Type of dialing AA Telephone line (analog only) Pulse Tone Control command AT commands EIA-578 commands Monitor function Computer’s speaker Communication specifications Communication system Data: Fax: Communication protocol Data ITU-T-Rec (Former CCITT) Bell Fax ITU-T-Rec (Former CCITT) V.21/V.22/V.22bis/V.32 /V.32bis/V.34/V.90 103/212A V.
Appendix B Display Controller and Modes APPENDIX B Display controller The display controller interprets software commands into hardware commands that turn particular pels on or off. The controller is an advanced Video Graphics Array (VGA) that provides Super VGA (SVGA) and Extended Graphics Array (XGA) support for the internal LCD and external monitors. Two models are available: ❑ 13.3" XGA, 1024 horizontal x 768 vertical pixels ❑ 14.
User's Manual Video modes The computer supports video modes defined in the table below. If your application offers a selection of mode numbers that do not match the numbers on the table, select a mode based on mode type, resolution, character matrix, number of colors and refresh rates. Also, consider the following points: APPENDIX B ❑ ❑ ❑ If your software supports both graphics and text modes, the screen display may appear to operate faster using a text mode.
Appendix B Table Video modes continued Type Resolution Character matrix (pels) LCD colors CRT colors Scanning frequency Vertical D VGA Grph 320 x 200 Pels 8x8 16 of 256K 16 of 256K 70Hz E VGA Grph 640 x 200 Pels 8x8 16 of 256K 16 of 256K 70Hz F VGA Grph 640 x 350 Pels 8 x 14 Mono Mono 70Hz 10 VGA Grph 640 x 350 Pels 8 x 14 16 of 256K 16 of 256K 70Hz 11 VGA Grph VGA Grph 640 x 480 Pels 640 x 480 Pels 8 x 16 2 of 256K 2 of 256K 60Hz 8 x 16 16 of 256K 16 of 256K 60Hz
User's Manual Table Video modes continued APPENDIX B Video mode Type Resolution Character matrix (pels) LCD colors CRT colors Scanning frequency Vertical SVGA 640 x 480 Grph Pels 64K of 64K 64K of 64K 60Hz 75Hz 85Hz SVGA 800 x 600 Grph Pels 64K of 64K 64K of 64K 60Hz 75Hz 85Hz SVGA 1024 x 768 Grph Pels 64K of 64K 64K of 64K 60Hz 75Hz 85Hz SVGA 1280 x 1024 Grph Pels 64K of 64K 64K of 64K 60Hz 75Hz 85Hz SVGA 1600 x 1200 Grph Pels 64K of 64K 64K of 64K 60Hz SVGA 640 x 480 Grph Pels 16M
Appendix C AT Commands In most cases, you will not need to type AT commands manually. However, there might be some occasions when you will need to do so. This chapter describes AT commands for data mode. Fax and voice commands are taken care of by application software. The format for entering AT commands is: ATXn Any command issued is acknowledged with a response in either text or numeric values known as result codes.
User's Manual A Answer command This command instructs the modem to go off-hook and answer an incoming call. Bn Communication standard setting This command determines the communication standard CCITT or Bell. B0 Selects CCITT V.22 mode when the modem is at 1200 bps. B1 Selects Bell 212A when the modem is at 1200 bps (default). B15 Selects V.21 when the modem is at 300 bps. B16 Selects Bell 103J when the modem is at 300 bps (default).
Appendix C ; Return to command mode. Causes the modem to return to command mode after dialing a number, without disconnecting the call. S=n Dial a telephone number previously stored using the &Zn=X command (See &Zn=X command for more information). The range is 0-3. En Echo command This command controls whether or not the characters entered from your computer keyboard are displayed on your monitor (echoed) while the modem is in command mode. E0 Disables echo to the computer.
User's Manual Ln Monitor speaker volume This command sets speaker volume to low, medium, or high. L0 Low volume. L1 Low volume. (Same as L0) L2 Medium volume (default). L3 High volume. Result Codes: OK n=0,1,2,3 ERROR Otherwise Mn Monitor speaker mode APPENDIX C This command turns the speaker on or off. M0 The speaker is off. M1 The speaker is on until the modem detects the carrier signal (default). M2 The speaker is always on when modem is off-hook.
Appendix C Result Codes: OK n=0,1 ERROR Otherwise On Return on-line to data mode O0 Instructs the modem to exit on-line command mode and return to data mode (see AT escape sequence, +++). O1 This command issues a retrain before returning to on-line data mode. O3 This command issues a rate renegotiation before returning to on-line data mode. Result Codes: OK n=0,1,3 P Select pulse dialing This command configures the modem for pulse (non touch-tone) dialing.
User's Manual T Select tone dialing This command instructs the modem to send DTMF tones while dialing. Dialed digits are tone dialed until a P command or dial modifier is received. This is the default setting. Vn DCE response format This command controls whether result codes (including call progress and negotiation progress messages) are displayed as words or their numeric equivalents. V0 Displays result codes as digits. V1 Displays result codes as text (default).
Appendix C X5 Enable Enable OK, RING, NO CARRIER, ERROR, NODIALTONE, BUSY, CONNECT , RRING, NO BONGTONE, DELAYED, BLACKLISTED, REORDER, WARBLE, CALL WAITING DETECTED Dial tone detect Disabled: The modem dials a call regardless of whether it detects a dial tone. Enabled: The modem dials only upon detection of a dial tone, and disconnects the call if the dial tone is not detected within 10 seconds. APPENDIX C Busy tone detect Disabled: The modem ignores any busy tones it receives.
User's Manual &C0 The state of the carrier from the remote modem is ignored. DCD circuit is always on. &C1 DCD turns on when the remote modem’s carrier signal is detected, and off when the carrier signal is not detected (default). Result Codes: OK n=0,1 ERROR Otherwise &Dn DTR control APPENDIX C This command interprets how the modem responds to the state of the DTR signal and changes to the DTR signal. &D0 Ignore. The modem ignores the true status of DTR and treats it as always on.
Appendix C &Gn V.22bis guard tone control This command determines which guard tone, if any, to transmit while transmitting in the high band (answer mode). This command is only used in V.22 and V.22bis mode. This option is not used in North America and is for international use only. &G0 Guard tone disabled (default). &G1 Sets guard tone to 550 Hz. &G2 Sets guard tone to 1800 Hz. Result Codes: n=0,1,2 OK ERROR Otherwise &Kn Local flow control selection Disable flow control.
User's Manual &T0 Abort. Stops any test in progress. &T1 Local analog loop. This test verifies modem operation, as well as the connection between the modem and computer. Any data entered at the local DTE is modulated, then demodulated, and returned to the local DTE. To work properly, the modem must be off-line. Result Codes: OK n=0 CONNECT n=1 ERROR Otherwise APPENDIX C &V Display Current Configuration This command displays the current configuration of the modem.
Appendix C Nn Error control mode selection \ This command determines the type of error control used by the modem when sending or receiving data. \N0 Buffer mode. No error control. \N1 Direct mode. \N2 MNP or disconnect mode. The modem attempts to connect using MNP2-4 error control procedures. If this fails, the modem disconnects. This is also known as MNP reliable mode. \N3 V.42, MNP, or buffered (default). \N4 V.42 or disconnect. The modem attempts to connect in V.42 error control mode.
User's Manual \Vn Protocol result code \V0 Disable protocol result code appended to DCE speed. \V1 Enable protocol result code appended to DCE speed (default). Result Codes: n=0,1 OK ERROR Otherwise %B View numbers in blacklist If blacklisting is in effect, this command displays the numbers for which the last call attempted in the past two hours failed. The ERROR result code appears in regions that do not require blacklisting.
Appendix C APPENDIX C C-13
Appendix D S-registers S-registers contain the settings that determine how a number of functions of the internal modem operate. For example, how many times to let the telephone ring before the modem answers and how long to wait before it hangs up if a connection fails. You can also customize certain AT commands such as the escape sequence and command line termination. The contents of the registers are changed automatically when you modify corresponding settings in your communication software.
User's Manual S0 Auto answer ring number This register determines the number of rings the modem will count before automatically answering a call. Enter 0 (zero) if you do not want the modem to automatically answer at all. When disabled, the modem can only answer with an ATA command. Range: 0-255 Default: 0 Units: rings S1 Ring counter This register is read only. The value of S1 is incremented with each ring. If no ring occurs over a six-second interval, this register is cleared.
Appendix D S4 Response formatting character (user defined) This register determines the ASCII value used as the line feed character. The modem uses a line feed character in command mode when it responds to the computer. Range: 0-127, ASCII decimal Default: 10 (line feed) Units: ASCII S5 Command line editing character (user defined) This register sets the character recognized as a backspace and pertains to asynchronous only.
User's Manual S7 Connection completion time-out This register sets the time, in seconds, that the modem must wait before hanging up because carrier is not detected. The timer is started when the modem finishes dialing (originate), or goes off-hook (answer). In originate mode, the timer is reset upon detection of an answer tone if allowed by county restriction. The timer also specifies the wait for silence time for the @ dial modifier in seconds. S7 is not associated with the W dial modifier.
Appendix D S37 Dial line rate maximum modem speed S37 = 1 reserved S37 = 2 1200/75 bps S37 = 3 300 bps S37 = 4 reserved S37 = 5 1200 bps S37 = 6 2400 bps S37 = 7 4800 bps S37 = 8 7200 bps S37 = 9 9600 bps S37 = 10 12000 bps S37 = 11 14400 bps S37 = 12 16800 bps S37 = 13 19200 bps S37 = 14 21600 bps S37 = 15 24000 bps S37 = 16 26400 bps S37 = 17 28800 bps S37 = 18 31200 bps S37 = 19 33600 bps APPENDIX D S37 = 0 (default) D-5
User's Manual AT command set result codes The following table shows the result codes.
Appendix D Result Code Numeric Description DELAYED*2 88 Delay is in effect for the dialed number BLACKLISTED*2 89 Dialed number is blacklisted BLACKLIST FULL*2 90 Blacklist is full *1: EC only appears when the Extended Result Codes configuration option is enabled. EC is replaced by one of the following symbols, depending upon the error control method used: V.42bis - V.42 error control and V.42bis data compression. V.42 - V.42 error control only.
APPENDIX D User's Manual D-8
Appendix E V.90 The TOSHIBA internal modem uses V.90 technology. The modem is capable of downstream speeds of 56Kbps (kilobits per second) when connected to an Internet service provider that supports V.90. As with any modem, the actual throughput (speed of data transfer) depends on analog telephone line conditions, which can vary considerably. Therefore, many users will experience throughput in the range of 32-44Kbps under normal telephone line conditions. Upstream data flows at the V. 34 rate. NOTE: V.
User's Manual APPENDIX E Table E-1 Result codes for a V.90 connection No.
Appendix E AT Command -V90=* V.90 Dial Line Rate -V90 sets the maximum V.90 downstream that the modem attempts to connect. -V90=0 V.90 disabled -V90=1 V.
APPENDIX E User's Manual E-4
Appendix F Wireless LAN This document is intended to help you get your Wireless LAN network up and running, with a minimum of parameters. About Toshiba Wireless solution The Wireless LAN card Kit enables you to: ❑ Connect your computer to a peer-to-peer workgroup of Wireless computing devices. ❑ Connect your computer to a Local Area Network (LAN) Infrastructure that includes Wireless LAN Access Points, or other IEEE802.11 compliant LAN systems.
APPENDIX F User’s Manual Peer-to-peer workgroup The peer-to-peer workgroup configuration enables you to quickly set up a small Wireless workgroup, where the workgroup participants can exchange files using features such as Files and Printer Sharing as supported by Microsoft Networking. Figure F-1 Peer-to-peer Wireless workgroup You can use this option to set up a temporary or ad-hoc network in environment where no access points are available, for example in Small Office/Home Office (SOHO) environments.
Appendix F APPENDIX F Enterprise networking Figure F-2 Stand-alone Wireless LAN With the Wireless LAN Access Points you can connect to a corporate Local Area Network (LAN) infrastructure to have Wireless access to all network facilities. LAN Infrastructures may either be.
APPENDIX F User’s Manual ❑ Wireless network infrastructures connected to an existing Ethernet network as pictured in Figure F-3. Figure F-3 LAN Infrastructure Easy configuration The Wireless LAN card functions like any standard wired Ethernet card except it gives you the freedom of Wireless connections. Where an Ethernet card requires a cable connection to a hub and/or patch panel, the cable physically limits the location of the wired connection. Expanding or re-designing your network is easy.
Appendix F The Wireless LAN card is a Wireless network card that complies with the IEEE 802.11 standard on Wireless LANs (Revision B). The Wireless LAN card supports data rates up to 11 Mbit/s. ❑ Wi-Fi (Wireless Fidelity) certified by the Wireless Ethernet Compatibility Alliance (WECA). This means that your Wireless hardware will communicate with other vendors’ IEEE 802.11 compliant Wireless LAN products.
APPENDIX F User’s Manual 5. Set the correct Network Name. Figure F-4 Edit Configuration window 6. In the field Network Name, define the name of the Wireless network to which you want to connect. You can either use: • The value ANY To connect to any Wireless LAN network in the vicinity of your computer. • An exact value to connect to a specific network. Consult your LAN administrator for the value that applies to your network.
Appendix F If you wish to connect to a peer-to-peer workgroup, use the Add/Edit Configuration Profile window to: 1. Click the Start button from the Windows task bar. 2. Click on Settings, and then on Control Panel. 3. In the Control Panel window, double-click the Wireless Network icon. 4. Select to connect to a peer-to-peer workgroup. 5. Set the correct Network Name and Encryption Key. Figure F-5 Edit Configuration window : peer-to-peer 6.
APPENDIX F User’s Manual • If there is not yet such a group available, your computer will automatically start one with this name. 7. Click OK to confirm and return to the Add/Edit Configuration Profile window. 8. Click OK again to finish.
Appendix F If you cannot find other Wireless LAN networked computers, verify whether the other Wireless LAN computers are: ❑ Powered up and logged onto the network. ❑ Configured to operate with identical Microsoft Network settings concerning: • Networking Protocol • Wireless Network Name • Workgroup Name To view or modify the Station Name or Workgroup of your computer, proceed as follows: 1. Click Start on the Windows task bar. 2. Click Settings, and then click Control Panel. 3.
APPENDIX F User’s Manual ❑ Click the icon once with your right mouse button to display a menu with more options. View Wireless link quality You can use Client Manager icon on the Windows task bar to verify the link quality of your network connection. An overview of all possible icons is given in Table1. When the Client Manager icon is not indicating excellent or good radio connection, act as described in Table F-1.
Appendix F If you would like to view or modify Wireless LAN parameters, for example because you would like to connect to another network or type of network, proceed as follows: 1. Right-click on the Client Manager icon on the Windows task bar. 2. From the menu, select Configuration Profile, see Figure F-6, and select: • Add/Edit Profile to add a new profile or to modify an existing profile. • One of the existing profiles (if present) to select a profile without viewing or modifying the settings.
APPENDIX F User’s Manual Advanced configurations Although your Wireless LAN card will work fine in most network environments with the Basic Parameters, you may wish to explore the advanced parameters options as displayed in the Wireless LAN card’s Edit Configuration window. You can set advanced parameters only if your computer is connected to an existing network. Consult your LAN administrator for details.
Appendix F APPENDIX F Advanced window Use this window to set advanced parameters. Figure F-8 Advanced window Card Power Management Interference Robustness RTS/CTS Medium To extend the battery life of (mobile) Wireless devices. Can be activated in exceptional cases when troubleshooting slow performance of a Wireless LAN network that could be related to in-band interference from devices such as microwave ovens.
APPENDIX F User’s Manual Admin window You can set the following parameters in the Admin window. Figure F-9 Admin parameters Distance between access points MAC address F-14 Depending on the number of access points in a Wireless LAN network this parameter controls the network performance. Can be activated in exceptional cases when troubleshooting slow performance of the Wireless LAN network that could be related to in-band interference from devices such as microwave ovens.
Appendix F APPENDIX F Card specifications Table F-2 Physical specifications Form Factor Mini-PCI TypeIIIA Dimensions Weight Temperature and Humidity Operation 0 to 55 C Maximum humidity 95% Transit -20 to 70 C 15 to 95% (no condensation) Storage -10 to 60 C 10 to 90% (no condensation) Although the card may still operate in the range of –20 to 70 C, operation outside the range of 0 to 55 C may no longer be according to specifications.
APPENDIX F User’s Manual Receive Mode 250mA Transmit Mode 350mA Power Supply 3.3V Table F-4 Networking Characteristics Compatibility ■ IEEE 802.11 Standard for Wireless LANS (DSSS) ■ Wi-Fi (Wireless Fidelity) certified by the Wireless Ethernet Compatibility Alliance (WECA) Network Operating System ■ Microsoft Windows® Networking Host Operating System Microsoft Windows® NT v4.0: ■ NDIS4 Miniport Driver MicrosoftWindows® 98/Me/2000 ■ NDIS5 Miniport Driver Microsoft Windows® XP ■ NDIS5.
Appendix F NOTE: Refer to the flyer Information to the User for regulatory information that may apply in your country/region. Table F-5 Radio characteristics R-F Frequency Band 2.4GHz (2400-2483.
APPENDIX F User’s Manual Table F-5 lists the typical ranges when used indoors in office environments such as the following: ❑ In Open Office environments, where antennas can see each other, i.e. there are no physical obstructions between them. ❑ In Semi-open Office environments, where work space is divided by shoulderheight, hollow wall elements; antennas are at desktop level. ❑ In Closed Office environments, work space is separated by floor-to-ceiling solid walls.
Appendix G AC Power Cord and Connectors Length: Minimum 2 meters Wire size: Minimum 0.75 mm2 Current rating: Minimum 2.5 amperes Voltage rating: 125 or 250 VAC (depending on country/region’s power standards) Certification agencies U.S. and Canada: UL listed and CSA certified No.
User's Manual The following illustrations show the plug shapes for the U.S.A. and Canada, the United Kingdom, Australia and Europe.
Appendix H Internal Modem Guide This appendix describes how to install and the remove the internal modem. CAUTION: Do not disassemble the computer beyond the steps described in this instruction or touch any components not specifically described. Installing the modem board To install the modem board, follow the steps below. 1. Save your data, quit Windows and turn off the power. 2. Disconnect the AC adaptor and any other peripheral devices. 3. Turn the computer upside down and remove the battery pack. 4.
User’s Manual Removing the modem board To remove the internal modem. 1. Save your data, quit Windows and turn off the power. 2. Disconnect the AC adaptor and any other peripheral devices. 3. Turn the computer upside down and remove the battery pack. 4. Remove one screw securing the modem cover and remove the cover. 5. Remove two screws securing the modem board. 6. Lift out the modem board. 7. Disconnect the modem board cable. 8. Secure the modem board with two screws removed in step 5. APPENDIX H 9.
Appendix I Parts Numbers The computer configuration and parts numbers, printed on a label on the bottom of the computer, indicate the CPU, LCD, memory, HDD, Slim Select Bay modules and communication devices.
I-2 14"TFT-XGA P933† 14TX 13TX 40 CD-RW/ DVD-ROM RW/ DV Modem/LAN/Wireless LAN Modem/LAN/Wireless LAN M/L/WL M/L/WL M/L CRW Modem/LAN CD-R/RW 30 30G 512M 512MB 40G M/L L Modem/LAN LAN DVD CD DVD-ROM CD-ROM 20 10 Communication 20G 10G Slim Select Bay 256M 128M HDD 256MB 128MB Memory † C incidates a Mobile Intel® Celeron™ processor and P indicates a Mobile Intel® Pentium® III processor-M. * Figures indicate the CPU operating speed in megahertz.
The terms in this glossary cover the topics discussed in this manual. Alternate naming is included for reference.
GLOSSARY AccuPoint (Abbreviations continued) SO-DIMM: small-outline dual in-line memory module SVGA: super video graphics adapter SDRAM: synchronized dynamic random access memory TFT: thin-film transistor UART: universal asynchronous receiver/transmitter USB: Universal Serial Bus VESA: Video Electronic Standards Association VGA: video graphics array VRM: video ready modem VRT: voltage reduction technology A AccuPoint: A pointing device integrated into the TOSHIBA computer keyboard.
byte AUTOEXEC.BAT: A batch file that executes a series of MS-DOS commands and programs each time you start the computer. B backup: A duplicate copy of files kept as a spare in case the original is destroyed. batch file: A file that can be executed from the system prompt containing a sequence of operating system commands or executable files. See also AUTOEXEC.BAT. binary: The base two number system composed of zeros and ones (off or on), used by most digital computers.
GLOSSARY cache memory C cache memory: High speed memory which stores data that increases processor speed and data transfer rate. When the CPU reads data from main memory, it stores a copy of this data in cache memory. The next time the CPU needs that same data, it looks for it in the cache memory rather than the main memory, which saves time. The computer has two cache levels. Level one is incorporated into the processor and level two resides in external memory. CGA: Color/graphics adapter.
delete components: Elements or parts (of a system) which make up the whole (system). computer program: A set of instructions written for a computer that enable it to achieve a desired result. computer system: A combination of hardware, software, firmware, and peripheral components assembled to process data into useful information. configuration: The specific components in your system (such as the terminal, printer, and disk drives) and the settings that define how your system works.
GLOSSARY device driver device driver: A program that controls communication between a specific peripheral device and the computer. The CONFIG.SYS file contains device drivers that MS-DOS loads when you turn the computer on. driver: A software program, generally part of the operating system, that controls a specific piece of hardware (frequently a peripheral device such as a printer or mouse). dialog box: A window that accepts user input to make system settings or record other information.
host computer Extended Capability Port: An industry standard that provides a data buffer, switchable forward and reverse data transmission, and run length encoding (RLE) support. F fast infrared: An industry standard that enables cableless infrared serial data transfer at speeds of up to 4 Mbps. file: A collection of related information; a file can contain data, programs, or both. firmware: A set of instructions built into the hardware which controls and directs a microprocessor’s activities.
GLOSSARY hot dock/undock hot dock/undock: Connecting or disconnecting a device to or from the computer while the computer’s power is turned on. hotkey: The computer’s feature in which certain keys in combination with the extended function key, Fn, can be used to set system parameters, such as speaker volume. HW Setup: A TOSHIBA utility that lets you set the parameters for various hardware components. I icon: A small graphic image displayed on the screen or in the indicator panel.
modem kilobyte (KB): A unit of data storage equal to 1024 bytes. See also byte and megabit. L level 2 cache: See cache. MDA: Monochrome Display Adapter. A video display protocol defined by the IBM Monochrome Display Adapter and its associated circuitry for direct drive TTL displays that supports a monochrome 720x350 text mode. megabyte (MB): A unit of data storage equal to 1024 kilobytes. See also kilobyte. megahertz: A unit of wave frequency that equals 1 million cycles per second. See also hertz.
GLOSSARY monitor monitor: A device that uses rows and columns of pixels to display alphanumeric characters or graphic images. See CRT. motherboard: A name sometimes used to refer to the main printed circuit board in processing equipment. It usually contains integrated circuits that perform the processor’s basic functions and provides connectors for adding other boards that perform special functions. Sometimes called a main board.
RAM password: A unique string of characters used to identify a specific user. The computer provides various levels of password protection such as user, supervisor and eject. pel: The smallest area of the display that can be addressed by software. Equal in size to a pixel or group of pixels. See pixel. peripheral component interconnect: An industry standard 32-bit bus. peripheral device: An I/O device that is external to the central processor and/ or main memory such as a printer or a mouse.
GLOSSARY restart restart: Resetting a computer without turning it off (also called ‘warm boot’ or ‘soft reset’). To restart the computer, press Ctrl + Alt + Del while the computer is on. See also boot. RCA jack: A single-pin connector that carries composite video signals, which include both contrast and color information. See also S-video. RGB: Red, green, and blue.
write protection V synchronous: Having a constant time interval between successive bits, characters or events. volatile memory: Random access memory (RAM) that stores information as long as the computer is connected to a power source. system disk: A disk that has been formatted with an operating system. For MS-DOS the operating system is contained in two hidden files and the COMMAND.COM file. You can boot a computer using a system disk. Also called an operating system disk.
GLOSSARY Glossary-14
Index C AC adaptor 1-6, 2-11 DC IN 15V port 2-4 additional 1-12, 8-11 connecting 3-5 AccuPoint II 1-6, 2-7 problems 9-16 using 4-1 Advanced Port Replicator 1-12, 8-11 ASCII characters 5-9 Auto power on, See Power Cache memory CPU cache 1-4 Level 2 cache 1-4 CD-ROM drive, See also Slim Select Bay 1-4, 4-4 CD-R/RW drive, See also Slim Select Bay 1-5, 4-5 CD-RW/DVD drive, See also Slim Select Bay 1-5, 4-5 Charger, See Battery charger Cleaning the computer 4-19 COM level, See Ports, serial Cooling 1-10, 4-20
INDEX User's Manual E H Environment 3-2 Equipment checklist 1-1 Equipment setup general conditions 3-2 placement 3-2 Ergonomics lighting 3-4 seating and posture 3-3 work habits 3-4 Expansion memory, See Memory expansion Hard disk drive 1-4 automatic power off 1-9 problems 9-9 Hibernation 1-10, 5-5 problems 9-22 Hotkeys 1-9, 5-4 display brightness 5-5 display selection 5-5 hibernation 5-5 instant security 5-4 power save mode 5-4 standby 5-4 sticky key utility 5-6 wireless setting 5-6 HW Setup 1-10 acces
Index K N Numeric keypad, See Keypad overlay L O LAN, See also Wireless LAN 1-7 cable types 4-14 connecting 4-14 disconnecting 4-15 problems 9-23 using 4-14 LCD, See Display, Video modes, Monitor external Level 2 cache, See Cache memory Lock, security, See Security lock Operating system 1-8 Overlay, See Keypad overlay M Main battery, See Battery pack Memory 1-4 expansion 1-12, 8-4 installing 8-4 removing 8-6 slots 1-4 Microphone, See sound system, microphone Microprocessor, See Processor P Panel pow
INDEX User's Manual LAN 2-4 microphone, See Sound system modem 2-4 parallel 1-6, 2-4 PS/2 keyboard/mouse 1-6, 2-4 serial 1-6, 2-4 USB 1-6, 2-4 Power auto power on 1-10 button location 2-7 indicator 2-8, 6-5 panel power on/off 1-9 restarting 3-9 turning off 3-8 turning on 3-7 system auto off 1-9 Printer parallel 7-6, 8-12 problems 9-15 Problems AccuPoint II 9-16 analyzing symptoms 9-2 CD-ROM drive 9-9 CD-R/RW drive 9-10 CD-RW/DVD-ROM drive 9-13 diskette drive 9-14 DVD-ROM drive 9-11 hard disk drive 9-9 har
Index INDEX Soft keys 5-2 cursor control mode 5-3 Enter 5-3 numeric mode 5-3 right Alt key 5-3 right Ctrl key 5-3 ScrLock 5-3 Sound system 1-7 drivers 1-11 headphone 1-6, 2-1 microphone 1-6, 2-1 problems 9-19 speaker 2-7 volume control 2-2 Standby 1-10 System auto off 1-9 T TOSHIBA Power Saver 1-10 Troubleshooting, See Problems TV 8-14 U Utilities list 1-10 USB 1-6 location 2-4 problems 9-20 V Video modes, Appendix B Vide-out jack 1-7, 2-2 Video RAM 1-4 Volume control, See Sound system W Windows® XP P
INDEX User's Manual Index-6
