TOSHIBA TE2300 TOSHIBA TE2300 User's Manual 160 bis 200 Seiten TE2300 Manuel de l’utilisateur TOSHIBA TE 2300 *T201929-FR* T201929-FR TOSHIBA TE2300 TOSHIBA TE2300 TOSHIBA TE2300 TOSHIBA TE2300 TOSHIBA TE2300 Choose freedom. Choose freedom. computers.toshiba-europe.com computers.toshiba-europe.
TE2300 Version 1 Last Saved on 21.05.2003 10:18 User’s Manual Copyright © 2003 by TOSHIBA Corporation. All rights reserved. Under the copyright laws, this manual cannot be reproduced in any form without the prior written permission of TOSHIBA. No patent liability is assumed, with respect to the use of the information contained herein.
TE2300 Version 1 Last Saved on 21.05.2003 10:18 User’s Manual EU Declaration of Conformity This product is carrying the CE-Mark in accordance with the related European Directives. Responsible for CE-Marking is TOSHIBA Europe GmbH, Hammfelddamm 8, 41460 Neuss, Germany. TOSHIBA TE2300 iii ENGLISH using TE2300_Onine.dot –– Printed on 27.05.
TE2300 Version 1 Last Saved on 21.05.2003 10:18 User’s Manual Modem warning notice Conformity Statement The equipment has been approved to [Commission Decision “CTR21”] for pan-European single terminal connection to the Public Switched Telephone Network (PSTN). However, due to differences between the individual PSTNs provided in different countries/regions the approval does not, of itself, give an unconditional assurance of successful operation on every PSTN network termination point.
TE2300 Version 1 Last Saved on 21.05.2003 10:18 User’s Manual General Precautions TOSHIBA computers are designed to optimize safety, minimize strain and withstand the rigors of portability. However, certain precautions should be observed to further reduce the risk of personal injury, damage to the computer or impaired performance. Be certain to read the general precautions below and to note the cautions included in the text of the manual. Please also refer to the Safety Instruction Manual.
TE2300 Version 1 Last Saved on 21.05.2003 10:18 User’s Manual Mobile phone Use of mobile phones can interfere with the audio system. Computer operation is not impaired but it is recommended that a distance of 30 cm be maintained between the computer and a mobile phone in use.
TE2300 Version 1 Last Saved on 21.05.2003 10:18 User’s Manual Working environment This product was designed to fulfil the EMC (electromagnetic compatibility) requirements to be observed for so-called "Residential, commercial and light industry environments". TOSHIBA do not approve the use of this product in working environments other than the above mentioned "Residential, commercial and light industry environments".
TE2300 Version 1 Last Saved on 21.05.2003 10:18 User’s Manual Network connection (class A warning) If this product has networking capabilities and will be connected to a network, Class A radiation limits will be observed (in accordance with technical conventions). This means that if the product will be used in a domestic environment, other devices in the near surrounding may suffer interference.
TE2300 Version 1 Last Saved on 21.05.2003 10:18 User’s Manual TOSHIBA TE2300 1. Table of Contents General Precautions Preface Manual contents ........................................................................... xii Conventions..................................................................................xiii Chapter 1: Introduction Equipment checklist.....................................................................1-1 Features ...............................................................
TE2300 Version 1 Last Saved on 21.05.2003 10:18 Table of Contents Chapter 3: Getting Started Setting up your work space .........................................................3-1 Connecting the AC adaptor .........................................................3-4 Opening the display .....................................................................3-6 Turning on the power ...................................................................3-6 Starting up for the first time ..........................
TE2300 Version 1 Last Saved on 21.05.2003 10:18 Table of Contents Chapter 7: HW Setup and Passwords HW Setup.....................................................................................7-1 Chapter 8: Optional Devices PC cards ......................................................................................8-2 Memory expansion ......................................................................8-3 Additional battery pack (Black) ....................................................
TE2300 Version 1 Last Saved on 21.05.2003 10:18 Table of Contents TOSHIBA TE2300 2. Preface Congratulations on your purchase of the TOSHIBA TE2300 series computer. This powerful, lightweight notebook computer is designed to provide years of reliable, high-performance computing. This manual tells how to set up and begin using your TE2300 computer. It also provides detailed information on configuring your computer, basic operations and care, using optional devices and troubleshooting.
TE2300 Version 1 Last Saved on 21.05.2003 10:18 Preface Manual contents This manual is composed of nine chapters, nine appendixes, a glossary, and an index. Chapter 1, Introduction, is an overview of the computer’s features, capabilities, and options. Chapter 2, The Grand Tour, identifies the components of the computer and briefly explains how they function. Chapter 3, Getting Started, provides a quick overview of how to begin operating your computer and gives tips on safety and designing your work area.
TE2300 Version 1 Last Saved on 21.05.2003 10:18 Preface Conventions This manual uses the following formats to describe, identify, and highlight terms and operating procedures. Abbreviations On first appearance, and whenever necessary for clarity, abbreviations are enclosed in parentheses following their definition. For example: Read Only Memory (ROM). Acronyms are also defined in the Glossary. Icons Icons identify ports, dials, and other parts of your computer.
TE2300 Version 1 Last Saved on 21.05.2003 10:18 Preface Please read. A note is a hint or advice that helps you make best use of your equipment. TOSHIBA TE2300 xv ENGLISH using TE2300_Onine.dot –– Printed on 27.05.
TE2300 Version 1 Last Saved on 21.05.2003 10:18 Preface TOSHIBA TE2300 1. Chapter 1 Introduction This chapter provides an equipment checklist, and it identifies the computer’s features, options and accessories. Some of the features described in this manual may not function properly if you use an operating system that was not preinstalled by TOSHIBA. Equipment checklist Carefully unpack your computer. Save the box and packing materials for future use.
TE2300 Version 1 Last Saved on 21.05.
TE2300 Version 1 Last Saved on 21.05.2003 10:18 Introduction ® Some models carry Intel CentrinoTM technology, which is based on three ® ® ® separate technologies of Intel Pentium M, Intel PRO/Wireless Network ® Connection, and Intel 855 Chipset Family. Memory Slots PC2100 256 or 512 or 1024MB memory modules can be installed in the two memory slots for a maximum of 2GB system memory. Level 2 cache A 1MB level 2 cache is provided to maximize performance.
TE2300 Version 1 Last Saved on 21.05.2003 10:18 Introduction CD-RW/DVD-ROM drive Some models are equipped with a full-size, CD-RW/DVD-ROM drive module that lets you run CD/DVDs without using an adaptor. It reads DVD-ROMs at maximum 8 speed and CD-ROMs at maximum 24 speed. It writes CD-R at up to 24 speed and CD-RW at up to 10 speed. See Chapter 4, Operating Basics, for details. For reading, this drive supports the same formats as the DVD-ROM drive.
TE2300 Version 1 Last Saved on 21.05.2003 10:18 Introduction Power Battery pack The computer is powered by one rechargeable lithium-ion battery pack. RTC battery The internal RTC battery backs up the Real Time Clock (RTC) and calendar. AC adaptor The universal AC adaptor provides power to the system and recharges the batteries when they are low. It comes with a detachable power cord. Because it is universal, it can receive a range of AC voltage between 100 and 240 volts.
TE2300 Version 1 Last Saved on 21.05.2003 10:18 Introduction Multimedia Sound System Windows Sound System compatible sound system provides internal speaker as well as jacks for an external microphone and headphone. It also has a volume control dial. Video-out jack This RCA jack lets you transfer NTSC-J, NTSC-M or PAL-B data to external devices. Communications Modem An internal modem provides capability for data and fax communication. It supports V.92 (US/Canda) and V.90 (other countries/regions).
TE2300 Version 1 Last Saved on 21.05.2003 10:18 Introduction Software ® Operating System Windows XP Professional is available. Refer to the preinstalled software section at the front of this chapter. TOSHIBA Utilities A number of utilities and drivers are preinstalled to make your computer more convenient to use. Refer to the Utilities section in this chapter.
TE2300 Version 1 Last Saved on 21.05.2003 10:18 Introduction Battery save mode This feature lets you save battery power. You can specify the Power Save Mode in the Running on batteries item of the Power Save Modes window in Power Saver. Power on password. Two levels of password security are available: supervisor and user. This feature prevents unauthorized access to your computer. Instant security A hotkey function blanks the screen and disables the computer providing quick and easy data security.
TE2300 Version 1 Last Saved on 21.05.2003 10:18 Introduction Heat dispersal To protect from overheating, the CPU has an internal temperature sensor. If the computer’s internal temperature rises to a certain level, the cooling fan is turned on or the processing speed is lowered. Use the Fan item of the Power Save Modes window in Power Saver. Maximum Performance Turns on fan first, then if necessary lowers CPU processing speed. Performance Uses a combination of fan and lowering the CPU processing speed.
TE2300 Version 1 Last Saved on 21.05.2003 10:18 Introduction TOSHIBA Mobile Extension This utility enables hot insertion of Slim Select Bay modules, that is, you can remove/insert Slim Select Bay modules while the computer is on. To activate this utility, select TOSHIBA Mobile Extension from TOSHIBA Console. ConfigFree ConfigFree is a suite of utilities to allow easy control of communication device and network connections.
TE2300 Version 1 Last Saved on 21.05.2003 10:18 Introduction Advanced Port Replicator II The Port Replicator provides the ports available on the computer in addition to separate PS/2 mouse and PS/2 keyboard ports, a digital visual interface (DVI) port, i.LINK™ (IEEE1394) port, line-in jack and line-out jack. The TE2300 does not support the DVI and i.LINK ports on the Advanced Port Replicator II. Slim Select Bay options The following modules can be installed in the Slim Select Bay.
TE2300 Version 1 Last Saved on 21.05.2003 10:18 TOSHIBA TE2300 2. Chapter 2 The Grand Tour This chapter identifies the various components of your computer. Become familiar with each component before you operate the computer. Front with the display closed The figure below shows the computer’s front with its display panel in the closed position.
TE2300 Version 1 Last Saved on 21.05.2003 10:18 The Grand Tour This infrared port is compatible with Infrared Data Association (IrDA 1.1) standards. It enables cableless 4 Mbps, 1.152 Mbps, 115.2 Kbps, 57.6 Kbps, 38.4 Kbps, 19.2 Kbps or 9.6 Kbps data transfer with IrDA 1.1 compatible external devices. Infrared port Left side The figure below shows the computer’s left side.
TE2300 Version 1 Last Saved on 21.05.2003 10:18 The Grand Tour Set the switch to off in airplanes and hospitals. Check the Wireless communication indicator. It will stop glowing when the wireless communication is off. Volume control Use this dial to adjust the volume of the system speakers and headphones. Right side The figure below shows the computer’s right side. The right side of the computer TOSHIBA TE2300 2-3 ENGLISH using TE2300_Onine.dot –– Printed on 27.05.
TE2300 Version 1 Last Saved on 21.05.2003 10:18 The Grand Tour Back side The figure below shows the computer’s back side. LAN ACTIVE FAN VENT DC IN 15V LINK INDICATOR (GREEN) MODEM JACK EXTERNAL MONITOR PORT PARALLEL PORT LAN JACK INDICATOR (ORANGE) USB PORTS SERIAL PS/2 KEYBOARD/ PORT MOUSE PORT The computer’s back side DC IN 15V The AC adaptor connects to this socket. Use only the model of AC adaptor that comes with the computer. Using the wrong adaptor can damage your computer.
TE2300 Version 1 Last Saved on 21.05.2003 10:18 The Grand Tour Ether LAN jack This jack lets you connect to a LAN. The adaptor has built-in support for Ethernet LAN (10 megabits per second, 10BASE-T) and Fast Ethernet LAN (100 megabits per second, 100BASE-Tx). LAN active indicator (orange) This indicator glows orange when data is being exchanged between the computer and the LAN.
TE2300 Version 1 Last Saved on 21.05.2003 10:18 The Grand Tour Underside The figure below shows the underside of the computer. Make sure the display is closed before turning over your computer. DOCKING HOLES DOCKING PORT DOCKING HOLES MEMORY BATTERY PACK LOCK MODULE COVER SLIM SELECT BAY LOCK BATTERY RELEASE LATCH SLIM SELECT BAY LATCH BATTERY PACK The underside of the computer Docking port Use this port to connect an optional Advanced Port Replicator II.
TE2300 Version 1 Last Saved on 21.05.2003 10:18 The Grand Tour Slim Select Bay lock There are two screw holes next to the Slim Select Bay latch. One screw is initially set in the front hole, which is the unlock position. To lock the Slim Select Bay latch, set the screw in the back hole. Use a point size 0 Phillips screwdriver. Slim Select Bay latch Slide this latch to free the Slim Select Bay for removal.
TE2300 Version 1 Last Saved on 21.05.2003 10:18 The Grand Tour Display screen The full-color LCD displays high-contrast text and graphics and is compatible with the industry standard eXtended Graphics Array (XGA). The LCD consists of up to 1024 × 768 pixels or dots. The computer has a Thin-Film Transistor (TFT) display. Refer to Appendix E. When the computer operates on power through the AC adaptor, the display screen’s image will be somewhat brighter than when it operates on battery power.
TE2300 Version 1 Last Saved on 21.05.2003 10:18 The Grand Tour System Indicators The figure below shows the indicators, which light when various computer operations are in progress. DC IN POWER MAIN BATTERY DISK SLIM SELECT WIRELESS BAY COMMUNICATION The power source/system indicators Power source/system indicators DC IN The DC IN indicator glows green when DC power is supplied from the AC power adaptor.
TE2300 Version 1 Last Saved on 21.05.2003 10:18 The Grand Tour The figures below show the positions of the keypad overlay indicators and the CapsLock indicator. When the F10 key indicator glows the keypad overlay lets you enter numbers. When the F11 key indicator glows the keypad overlay lets you control the cursor. NUMERIC MODE ARROW MODE Keypad overlay indicators When the CapsLock indicator glows the keyboard is in all-caps mode.
TE2300 Version 1 Last Saved on 21.05.2003 10:18 The Grand Tour USB diskette drive Some computers in this series come with a 3 1/2" diskette drive that accommodates 1.44-megabyte or 720-kilobyte diskettes. It connects to the USB port. DISK-IN-USE INDICATOR DISKETTE SLOT EJECT BUTTON USB diskette drive Disk-In-Use Indicator This indicator lights when the diskette is being accessed. Diskette slot Insert diskette in this slot.
TE2300 Version 1 Last Saved on 21.05.2003 10:18 The Grand Tour Slim Select Bay modules The Slim Select Bay can accommodate the following modules: DVD-ROM drive, CD-RW/DVD-ROM drive, DVD multi drive, optional Slim Select Bay HDD adaptor and optional Slim Select Bay 2nd battery pack. DVD-ROM drive An optional full-size DVD-ROM drive module lets you run either 12 cm (4.72") or 8 cm (3.15") CD/DVDs without using an adaptor. It may be selected as a standard component or as an option.
TE2300 Version 1 Last Saved on 21.05.2003 10:18 The Grand Tour Check the Slim Select Bay indicator when you use the DVD-ROM drive. Do not press the eject button, disconnect a drive or turn off the computer while the light is glowing. Doing so could damage the DVD/CD or the drive. DVD-ROM drives and media are manufactured according to the specifications of six marketing regions. When you purchase DVD media, make sure it matches your drive, otherwise it will not play properly.
TE2300 Version 1 Last Saved on 21.05.2003 10:18 The Grand Tour CD-RW describes compact disks that can be recorded more than once. Use either 1, 2, or 4 multi speed CD-RW disks or high-speed 4- to 10speed disks. The write speed of the high-speed CD-RW disks is maximum 8-speed. ■ Use Drag’n Drop CD+DVD to write compact disks. The physical features of this drive are similar to those of the DVD-ROM drive. Refer to the illustration in the DVD-ROM drive section.
TE2300 Version 1 Last Saved on 21.05.
TE2300 Version 1 Last Saved on 21.05.2003 10:18 The Grand Tour Slim Select Bay HDD adaptor (Black) You can increase your computer’s data storage capacity by installing an optional, integrated, 2 1/2" HDD in the Slim Select Bay. The Slim Select Bay HDD adaptor Slim Select Bay 2nd battery pack (Black) An optional battery pack can be installed in the Slim Select Bay to increase the computer’s battery power and operating time. For details, refer to the documentation accompanying the secondary battery pack.
TE2300 Version 1 Last Saved on 21.05.2003 10:18 The Grand Tour AC adaptor The AC adaptor converts AC power to DC power and reduces the voltage supplied to the computer. It can automatically adjust to any voltage from 100 to 240 volts and to a frequency of either 50 or 60 hertz, enabling you to use the computer in almost any region. To recharge the battery, simply connect the AC adaptor to a power source and the computer. See Chapter 6, Power and Power-Up Modes, for details.
TE2300 Version 1 Last Saved on 21.05.2003 10:18 The Grand Tour TOSHIBA TE2300 3. Chapter 3 Getting Started This chapter provides basic information to get you started using your computer. It covers the following topics: ■ Setting up your work space — for your health and safety Be sure also to read the Safety Instruction Manual. This guide, which is included with the computer, explains product liability.
TE2300 Version 1 Last Saved on 21.05.2003 10:18 Getting Started Setting up your work space Establishing a comfortable work site is important for you and your computer. A poor work environment or stressful work habits can result in discomfort or serious injury from repetitive strain to your hands, wrists or other joints. Proper ambient conditions should also be maintained for the computer’s operation.
TE2300 Version 1 Last Saved on 21.05.2003 10:18 Getting Started ■ Place the computer so that it is directly in front of you when you work and make sure you have adequate space to easily operate other devices. ■ Allow adequate space behind the computer to let you freely adjust the display. The display should be angled to reduce glare and maximize visibility. ■ If you use a paper holder, set it at about the same height and distance as the computer.
TE2300 Version 1 Last Saved on 21.05.2003 10:18 Getting Started Lighting Proper lighting can improve legibility of the display and reduce eye strain. ■ Position the computer so that sunlight or bright indoor lighting does not reflect off the screen. Use tinted windows, shades or other screen to eliminate sun glare. ■ Avoid placing the computer in front of bright light that could shine directly in your eyes. ■ If possible, use soft, indirect lighting in your computer work area.
TE2300 Version 1 Last Saved on 21.05.2003 10:18 Getting Started Connecting the AC adaptor Attach the AC adaptor when you need to charge the battery or you want to operate from AC power. It is also the fastest way to get started, because the battery pack will need to be charged before you can operate from battery power. The AC adaptor can be connected to any power source supplying from 100 to 240 volts and 50 or 60 hertz.
TE2300 Version 1 Last Saved on 21.05.2003 10:18 Getting Started Opening the display The display panel can be rotated in a wide range of angles for optimal viewing. 1. 2. Slide the display latch on the front of the computer to the right to unlatch the display panel. Lift the panel up and adjust it to the best viewing angle for you. When you open the display, hold it with both hands and lift up slowly.
TE2300 Version 1 Last Saved on 21.05.2003 10:18 Getting Started Starting up for the first time When you first turn on the power, the computer’s initial screen is the ® Microsoft Windows XP Professional Startup Screen Logo. Follow the on-screen directions. Turning off the power The power can be turned off in one of the following modes: Shut down (Boot), Hibernation or Standby mode.
TE2300 Version 1 Last Saved on 21.05.2003 10:18 Getting Started Benefits of hibernation The hibernation feature provides the following benefits: ■ Saves data to the hard disk when the computer automatically shuts down because of a low battery. For the computer to shut down in hibernation mode, the hibernation feature must be enabled in two places in TOSHIBA Power Saver: the Hibernate window and the Battery Alarm item of the Alarm window. Otherwise, the computer will shut down in Standby mode.
TE2300 Version 1 Last Saved on 21.05.2003 10:18 Getting Started Data save in hibernation mode When you turn off the power in hibernation mode, the computer takes a moment to save current memory data to the hard disk. During this time, the Built-in HDD indicator will light. After you turn off the computer and memory is saved to the hard disk, turn off the power to any peripheral devices. Do not turn the computer or devices back on immediately.
TE2300 Version 1 Last Saved on 21.05.2003 10:18 Getting Started 3. Open Performance and Maintenance and open TOSHIBA Power Saver. Press the power button. This feature must be enabled. Refer to the System Power Mode item in Power Saver Utility described in the Control Panel. Open Performance and Maintenance and open TOSHIBA Power Saver. When you turn the power back on, you can continue where you left when you shut down the computer. 1.
TE2300 Version 1 Last Saved on 21.05.2003 10:18 Getting Started Restoring the complete system To restore the operating system and all preinstalled software, follow the steps below. When you reinstall the Windows operating system, the hard disk will be reformatted and all data will be lost. 1. Load the Product Recovery CD-ROM in the drive and turn off the computer’s power. 2. Hold down the F12 key and turn on the power. When In Touch with Tomorrow TOSHIBA appears, release the F12 key. 3.
TE2300 Version 1 Last Saved on 21.05.2003 10:18 Getting Started TOSHIBA TE2300 4. Chapter 4 Operating Basics This chapter gives information on basic operations including using AccuPoint II, USB diskette drive, optical media drives, the internal modem, Wireless LAN, LAN and changing Slim Select Bay modules. It also provides tips on caring for your computer, diskettes and CD/DVDs.
TE2300 Version 1 Last Saved on 21.05.2003 10:18 Operating Basics ■ You touch the AccuPoint II during power-up. ■ You apply constant, soft pressure during power-up. ■ There is a sudden temperature change. ■ Strong stress is applied to the AccuPoint II. If an error message appears, reboot the computer. If an error message does not appear, wait a moment for the pointer to stop, then continue operation. Replacing the cap The AccuPoint II cap is an expendable item that should be replaced after prolonged use.
TE2300 Version 1 Last Saved on 21.05.2003 10:18 Operating Basics Using the USB diskette drive A 3 1/2" diskette drive connects to the computer’s USB port. It accommodates 1.44-megabyte or 720-kilobyte diskettes. Refer to Chapter 2, The Grand Tour, for more information. Connecting 3 1/2" diskette drive To connect the drive, plug the diskette drive connector into a USB port. Refer to figure below. Make sure the connector is right side up and properly aligned with the socket.
TE2300 Version 1 Last Saved on 21.05.2003 10:18 Operating Basics Changing Slim Select Bay modules This section explains how to change modules in the Slim Select Bay. The illustrations show replacement of the DVD-ROM drive with the Slim Select Bay HDD adaptor. Therefore, the text refers to those modules. However, the procedures are the same for any of the other modules: CD-RW/DVD-ROM drive, DVD Multi drive, Slim Select Bay 2nd battery pack. 1.
TE2300 Version 1 Last Saved on 21.05.2003 10:18 Operating Basics SLIM SELECT BAY LATCH SLIM SELECT BAY MODULE Removing the DVD-ROM drive Installing a module Install the Slim Select Bay HDD adaptor as described below. 1. Insert the Slim Select Bay HDD adaptor in the computer as shown below and press until the ejector clicks. 2. If you want to lock the Slim Select Bay module, set the screw of the Slim Select Bay lock in the back hole.
TE2300 Version 1 Last Saved on 21.05.2003 10:18 Operating Basics Using optical media drives The text and illustrations in this section refer primarily to the DVD-ROM drive. However, operation is the same for the CD-RW/DVD-ROM and DVD Multi drives. The full-size drive provides high-performance execution of CD/DVD-ROM-based programs. You can run either 12 cm (4.72") or 8 cm (3.15") CD/DVDs without an adaptor. An ATAPI interface controller is used for CD/DVD-ROM operation.
TE2300 Version 1 Last Saved on 21.05.2003 10:18 Operating Basics Diameter 1.0mm Manual release with the eject hole 2. Grasp the drawer gently and pull until it is fully opened. Pulling the drawer open 3. Lay the CD/DVD, label side up, in the drawer. TOSHIBA TE2300 4-7 ENGLISH using TE2300_Onine.dot –– Printed on 27.05.
TE2300 Version 1 Last Saved on 21.05.2003 10:18 Operating Basics Inserting a CD/DVD When the drawer is fully opened, the edge of the computer will extend slightly over the CD/DVD tray. Therefore, you will need to turn the CD/DVD at an angle when you place it in the tray. After seating the CD/DVD, however, make sure it lies flat, as shown in the figure above. 1. Do not touch the laser lens. Doing so could cause misalignment. 2. Be careful to keep foreign matter from entering the drive.
TE2300 Version 1 Last Saved on 21.05.2003 10:18 Operating Basics Closing the DVD-ROM drawer Removing discs To remove the CD/DVD, follow the steps below and refer to the next figure. Do not press the eject button while the computer is accessing the DVDROM drive. Wait for the DVD-In-Use indicator to go out before you open the drawer. Also, if the CD/DVD is spinning when you open the drawer, wait for it to stop before you remove it. 1. To pop the drawer partially open, press the eject button.
TE2300 Version 1 Last Saved on 21.05.2003 10:18 Operating Basics Removing a CD/DVD 3. Push the center of the drawer to close it. Press gently until it locks into place. TOSHIBA TE2300 4-10 ENGLISH using TE2300_Onine.dot –– Printed on 27.05.
TE2300 Version 1 Last Saved on 21.05.2003 10:18 Operating Basics Writing CDs on CD-RW/DVD-ROM drive Depending on the type of drive installed, you may be able to write CDs. The CD-RW/DVD-ROM drive lets you write as well as read CD-ROMs. Observe the precautions in this section to ensure the best performance for writing CDs. For information on loading and unloading CDs refer to the Using optical media drive section. CD-R discs can be written to only once. CD-RW discs can be rewritten many times.
TE2300 Version 1 Last Saved on 21.05.2003 10:18 Operating Basics ■ Writing with software other than Drag’n Drop CD+DVD has not been confirmed. Therefore, operation with other software cannot be guaranteed. When writing or rewriting Note the following when you write or rewrite a CD-R or CD-RW. ■ Always copy data from the HDD to the CD. Do not use cut-and-paste. The original data will be lost if there is a write error.
TE2300 Version 1 Last Saved on 21.05.2003 10:18 Operating Basics Writing CD/DVDs on DVD Multi drive You can use the DVD Multi drive to write data to either CD-R/-RW or DVD-R/-RW/-RAM discs. Important message Before you write or rewrite to CD-R/-RW or DVD-R/-RW/-RAM disc, read and follow all set-up and operating instructions in this section. If you fail to do so, the DVD Multi drive may not function properly, and you may fail to write or rewrite, lose data or incur other damage.
TE2300 Version 1 Last Saved on 21.05.2003 10:18 Operating Basics TAIYOYUDEN CO., LTD. Mitsui Chemicals Inc. MITSUBISHI CHEMICAL CORPORATIONRICOH Co., Ltd. CD-R: Hitachi Maxell Ltd. CD-RW: MITSUBISHI CHEMICAL CORPORATION RICOH Co., Ltd. DVD-R: DVD Specifications for Recordable Disc for GeneralVersion 2.0 TAIYOYUDEN CO., LTD. PIONEER VIDEO CORPORATION MITSUBISHI CHEMICAL CORPORATION DVD-RW: DVD Specifications for Re-recordable Disc for Version 1.1 VICTOR COMPANY OF JAPAN.
TE2300 Version 1 Last Saved on 21.05.2003 10:18 Operating Basics ■ In writing to a DVD-R/-RW disc, some disc space is required for file management, so you may not be able to write the full capacity of the disc. ■ Since the disc is based on the DVD standard, it will be filled with dummy data if the written data is less than about 1 GB. Even if you write only a small amount of data, it might take time to fill in the dummy data.
TE2300 Version 1 Last Saved on 21.05.2003 10:18 Operating Basics ■ ■ ■ ■ ■ ■ Install, remove or connect external devices, including the following: PC card, USB devices, external display, i.LINK devices, optical digital devices. ■ Use the Audio/Video control button to reproduce music or voice. ■ Open the DVD Multi drive Do not use standby/hibernation while you write or rewrite. Make sure writing or rewriting is completed before going into standby/ hibernation.
TE2300 Version 1 Last Saved on 21.05.2003 10:18 Operating Basics The “Record and Verify” function automatically checks whether data has been correctly recorded onto a CD/DVD. “Byte compare” compares the original data file with the data recorded on the CD/DVD and checks that the data completely matches. Media care This section provides tips on protecting data stored on your CD/DVDs and diskettes. Handle your media with care.
TE2300 Version 1 Last Saved on 21.05.2003 10:18 Operating Basics Modem This section describes how to connect and disconnect the internal modem to and from a telephone jack. The internal modem does not support voice functions. All data and fax functions are supported. 1. In case of a lightning storm, unplug the modem cable from the telephone jack. 2. Do not connect the modem to a digital telephone line. A digital line will damage the modem.
TE2300 Version 1 Last Saved on 21.05.2003 10:18 Operating Basics The menu list (Windows XP) Setting You can enable or disable the following settings: AutoRun Mode The Region Select utility starts automatically when you start up the operating system. Open the Dialing Properties dialog box after selecting region. The dialing properties dialog box will be displayed automatically after you select the region. Location list for region selection. A submenu appears displaying location information for telephony.
TE2300 Version 1 Last Saved on 21.05.2003 10:18 Operating Basics Connecting To connect the internal modem cable, follow the steps below. 1. Plug one end of the modular cable into the modem jack. 2. Plug the other end of the modular cable into a telephone jack.
TE2300 Version 1 Last Saved on 21.05.2003 10:18 Operating Basics Wireless LAN The Wireless LAN is compatible with other LAN systems based on Direct Sequence Spread Spectrum radio technology that complies with IEEE 802.11 Wireless LAN standard (Revision A or B) and Turbo Mode. It supports the following features: ■ Automatic Transmit Rate Select mechanism in the transmit range of 54, 48, 36, 24, 18, 12, 9 and 6 Mbit/s. (Revision A) ■ Automatic Transmit Rate Select mechanism in the transmit range of 11, 5.
TE2300 Version 1 Last Saved on 21.05.2003 10:18 Operating Basics Wireless communication Indicator The wireless communication indicator indicates the status of the wireless communication functions. Indicator status Indication Indicator off Wireless communication switch is set to off. Automatic power down because of overheating. Power malfunction Indicator glows Wireless communication switch is on. Wireless LAN is turned on by an application.
TE2300 Version 1 Last Saved on 21.05.2003 10:18 Operating Basics 2. Plug one end of the cable into the LAN jack. Press gently until you hear the latch click into place. Connecting the LAN cable 3. Plug the other end of the cable into a LAN hub connector. Check with your LAN administrator before connecting to a hub. When the computer is exchanging data with the LAN, the LAN active indicator glows orange.
TE2300 Version 1 Last Saved on 21.05.2003 10:18 Operating Basics Cleaning the computer To help ensure long, trouble-free operation, keep the computer free of dust and use care with liquids around the computer. ■ Be careful not to spill liquids into the computer. If the computer does get wet, turn the power off immediately and let the computer dry completely before you turn it on again. ■ Clean the computer using a slightly damp (with water) cloth. You can use glass cleaner on the display.
TE2300 Version 1 Last Saved on 21.05.2003 10:18 Operating Basics Heat dispersal To protect from overheating, the CPU has an internal temperature sensor. If the computer’s internal temperature rises to a certain level, the cooling fan is turned on or the processing speed is lowered. You can select whether to control the CPU temperature by turning on the fan first, then if necessary, lowering the CPU speed. Or, by lowering the CPU speed first, then if necessary, turning on the fan.
TE2300 Version 1 Last Saved on 21.05.2003 10:18 Operating Basics TOSHIBA TE2300 5. Chapter 5 The Keyboard The computer’s keyboard layouts are compatible with a 101/102-key enhanced keyboard. By pressing some keys in combination, all the 101/102-key keyboard functions can be executed on the computer. The number of keys on your keyboard depends on which country/region’s keyboard layout your computer is configured with. Keyboards for numerous languages are available.
TE2300 Version 1 Last Saved on 21.05.2003 10:18 The Keyboard F1 … F12 function keys The function keys, not to be confused with Fn, are the 12 keys at the top of your keyboard. These keys are dark gray, but function differently from the other dark gray keys. F1 through F12 are called function keys because they execute programmed functions when pressed. Used in combination with the Fn key, keys marked with icons execute specific functions on the computer.
TE2300 Version 1 Last Saved on 21.05.2003 10:18 The Keyboard Press Fn + F10 or Fn + F11 to access the integrated keypad. When activated, the keys with white markings on the bottom edge become numeric keypad keys (Fn + F11) or cursor control keys (Fn + F10). Refer to the Keypad overlay section in this chapter for more information on how to operate these keys. The power on default for both settings is off. Press Fn + F12 (ScrLock) to lock the cursor on a specific line. The power on default is off.
TE2300 Version 1 Last Saved on 21.05.2003 10:18 The Keyboard Instant security: Press Fn + F1 to lock the keyboard and blank the screen to prevent others from accessing your data. To restore the screen and original settings, press any key or move the AccuPoint II. When a dialog box appears, enter the screensaver password and click OK. If no password is set, the screen will be restored when you press any key. Power save mode: Pressing Fn + F2 changes the power save mode.
TE2300 Version 1 Last Saved on 21.05.2003 10:18 The Keyboard Display Brightness: Pressing Fn + F6 decreases the display brightness in increments. When you press these hotkeys, the current setting will be displayed for two seconds by an icon. You can also change this setting through the Monitor brightness item of the Power Save Mode window in Power Saver. Display Brightness: Pressing Fn + F7 increases the display brightness in increments.
TE2300 Version 1 Last Saved on 21.05.2003 10:18 The Keyboard Windows special keys The keyboard provides two keys that have special functions in Windows : one activates the Start menu and the other has the same function as the secondary mouse button. This key activates the Windows Start menu. This key has the same function as the secondary mouse button. Keypad overlay Your computer’s keyboard does not have an independent numeric keypad, but its numeric keypad overlay functions like one.
TE2300 Version 1 Last Saved on 21.05.2003 10:18 The Keyboard The numeric keypad overlay Temporarily using normal keyboard (overlay on) While using the overlay, you can temporarily access the normal keyboard without turning off the overlay: 1. Hold Fn and press any other key. All keys will operate as if the overlay were off. 2. Type uppercase characters by holding Fn + Shift and pressing a character key. 3. Release Fn to continue using the overlay.
TE2300 Version 1 Last Saved on 21.05.2003 10:18 The Keyboard Temporarily changing modes If the computer is in Numeric mode, you can switch temporarily to Arrow mode by pressing a shift key. If the computer is in Arrow mode, you can switch temporarily to Numeric mode by pressing a shift key. Generating ASCII characters Not all ASCII characters can be generated using normal keyboard operation. But, you can generate these characters using their ASCII codes. With the overlay on: 1. Hold down Alt. 2.
TE2300 Version 1 Last Saved on 21.05.2003 10:18 The Keyboard TOSHIBA TE2300 6. Chapter 6 Power and Power-Up Modes The computer’s power resources include the AC adaptor and internal batteries. This chapter gives details on making the most effective use of these resources including charging and changing batteries, tips for saving battery power, and power up modes.
TE2300 Version 1 Last Saved on 21.05.
TE2300 Version 1 Last Saved on 21.05.2003 10:18 Power and Power-Up Modes 3 * 4 * 5 * For the computer to shut down in hibernation mode, the hibernation feature must be enabled in two places in TOSHIBA Power Saver: the Hibernate window and the Battery Alarm item of the Alarm window. If a main battery and a secondary battery are installed, the computer does not shut down until the charge in both batteries is exhausted.
TE2300 Version 1 Last Saved on 21.05.2003 10:18 Power and Power-Up Modes DC IN indicator Check the DC IN indicator to determine the power status with the AC adaptor connected: Green Indicates the AC adaptor is connected and supplying proper power to the computer. Flashing orange Indicates a problem with the power supply. Plug the AC adaptor into another outlet. If it still does not operate properly, see your dealer. No light Under any other conditions, the indicator does not light.
TE2300 Version 1 Last Saved on 21.05.2003 10:18 Power and Power-Up Modes When the computer is powered off in Resume mode, and the AC adaptor in not connected, the main battery pack and optional secondary battery pack supply power to maintain data and programs in memory. If the battery pack(s) is completely discharged, Resume does not function and the computer loses all data in memory. The following message appears when you turn on the power: WARNING: RESUME FAILURE. PRESS ANY KEY TO CONTINUE.
TE2300 Version 1 Last Saved on 21.05.2003 10:18 Power and Power-Up Modes Care and use of the battery pack The battery pack is a vital component of portable computing. Taking proper care of it will help ensure longer operating time on battery power as well as a longer life for your battery pack. Follow the instructions in this section carefully to ensure safe operation and maximum performance. Safety precautions Mishandling of batteries can cause death, serious injury or property damage.
TE2300 Version 1 Last Saved on 21.05.2003 10:18 Power and Power-Up Modes 6. 7. 8. 9. Use only the battery pack supplied with the computer or other device or an battery pack approved by the computer or device's manufacturer. Battery packs have different voltages and terminal polarities. Use of an improper battery could cause smoke, fire or rupture of the battery pack. Never subject a battery pack to heat, such as storage near a heat source.
TE2300 Version 1 Last Saved on 21.05.2003 10:18 Power and Power-Up Modes 2. 3. 4. 5. 6. 7. Never dispose of battery packs with normal trash. Bring them to your TOSHIBA dealer or to another recycling center to save resources and prevent environmental damage. Cover the terminals with electrical tape to prevent short-circuits, which could cause the battery pack to ignite or rupture. Use only battery packs recommended by TOSHIBA as replacements.
TE2300 Version 1 Last Saved on 21.05.2003 10:18 Power and Power-Up Modes The computer enters Hibernate mode only if Hibernation is enabled in two places in TOSHIBA Power Saver : the Hibernate window and the battery Alarm item of the Alarm window. You must recharge a battery pack when it becomes discharged. Procedures To recharge a battery pack while it is installed in the computer, connect the AC adaptor to the DC IN socket and plug the other end into a working outlet.
TE2300 Version 1 Last Saved on 21.05.2003 10:18 Power and Power-Up Modes ■ The battery has completely discharged and been left in the computer for a long time. ■ A cool battery is installed in a warm computer. In such case, follow the steps below. 1. Fully discharge the battery by leaving it in the computer with the power on until the power automatically shuts off. 2. Plug in the AC adaptor. 3. Charge the battery until the Battery indicator glows green.
TE2300 Version 1 Last Saved on 21.05.2003 10:18 Power and Power-Up Modes ■ Turn off hard disks ■ How often and how long you use the hard disk, CD/DVD-ROM drive and the diskette drive. ■ How much charge the battery contained to begin with. ■ How you use optional devices, such as a PC card, to which the battery supplies power. ■ Enabling Resume mode conserves battery power if you are frequently turning the computer off and on. ■ Where you store your programs and data.
TE2300 Version 1 Last Saved on 21.05.2003 10:18 Power and Power-Up Modes ■ If you have extra battery packs, rotate their use. ■ If you will not be using the system for an extended period, more than one month, remove the battery pack. ■ Disconnect the AC adaptor when the battery is fully charged. Overcharging makes the battery hot and shortens life. ■ If you are not going to use the computer for more than eight hours, disconnect the AC adaptor.
TE2300 Version 1 Last Saved on 21.05.2003 10:18 Power and Power-Up Modes BATTERY RELEASE BATTERY PACK LATCH Removing the battery pack Installing the battery pack To install a battery pack, follow the steps below. The battery pack is a lithium ion battery, which can explode if not properly replaced, used, handled or disposed of. Dispose of the battery as required by local ordinances or regulations. Use only batteries recommended by TOSHIBA as replacements. 1. 2.
TE2300 Version 1 Last Saved on 21.05.2003 10:18 Power and Power-Up Modes Password = 2. 3. Enter the password. Press Enter. The computer displays the message below while it starts up. Valid password entered, system is now starting up. If you enter the password incorrectly three times in a row, the computer shuts off. In this case, you must turn the computer back on to retry password entry. Power-up modes The computer has the following power-up modes: ■ Boot : Computer shuts down without saving data.
TE2300 Version 1 Last Saved on 21.05.2003 10:18 Power and Power-Up Modes TOSHIBA TE2300 7. Chapter 7 HW Setup and Passwords This chapter explains how to use the TOSHIBA HW Setup program to configure your computer and how to set passwords. HW Setup TOSHIBA HW Setup lets you configure settings for pointing devices, display, CPU, boot priority, keyboard, USB, LAN, general, password, device config and parallel/printer.
TE2300 Version 1 Last Saved on 21.05.2003 10:18 HW Setup and Passwords General This window displays the BIOS version and contains two buttons: Default and About. Default Return all HW Setup values to the factory settings. About Display the HW Setup version. Setup This field displays BIOS Version and date. Password User Password This option allows you to set or reset the user password for power on. Not Registered Change or remove the password. (Default) Registered Set the password.
TE2300 Version 1 Last Saved on 21.05.2003 10:18 HW Setup and Passwords 2. Enter the currently registered password. The character string you enter is displayed as a string of asterisks. Enter Password: **** If you click the OK button before entering the password, Registered will appear on the display. 3. Click the OK button.
TE2300 Version 1 Last Saved on 21.05.2003 10:18 HW Setup and Passwords Pointing Devices Pointing Devices This tab lets you select Auto-Selected and Simultaneous. Auto-Selected If a PS/2 mouse is connected to the computer when you turn on the power, the PS/2 mouse is enabled and the AccuPoint II is disabled. Otherwise, the AccuPoint II is enabled. (Default) Simultaneous Enables both the AccuPoint II and a PS/2 mouse.
TE2300 Version 1 Last Saved on 21.05.2003 10:18 HW Setup and Passwords Boot Priority Boot Priority Options This option sets the priority for booting the computer. Select from the following settings: HDD −> FDD −> CD -ROM(-> LAN) The computer looks for bootable files in the following order: HDD, diskette drive, CD-ROM* and LAN. (default) FDD −> HDD −> CD -ROM(-> LAN) The computer looks for bootable files in the following order: diskette drive, HDD, CD-ROM* and LAN.
TE2300 Version 1 Last Saved on 21.05.2003 10:18 HW Setup and Passwords A bar will appear only under the selected device. 3. Use the left/right cursor keys to highlight boot device you want and press Enter. 1. If a supervisor password is set, the menu above does not appear when you use the user password to start the computer. 2. The selection method above does not change the boot priority settings in HW Setup. 3.
TE2300 Version 1 Last Saved on 21.05.2003 10:18 HW Setup and Passwords If you select Left Ctrl + Left Alt or Right Ctrl + Right Alt for this option, you cannot use the selected keys to reboot the computer in combination with the Del key. For example, if you select Left Ctrl + Left Alt, you must use Right Ctrl, Right Alt and Del to reboot the computer. Left Ctrl, Left Alt and Del cannot be used.
TE2300 Version 1 Last Saved on 21.05.2003 10:18 HW Setup and Passwords Do not install or remove an optional memory module while Wake-up on LAN is enabled. Wake-up on LAN does not work without the AC adaptor. Leave it connected, if you are using this feature. Built-in LAN Enabled Enables built-in LAN functions. (Default) Disabled Disables built-in LAN functions. TOSHIBA TE2300 7-8 ENGLISH using TE2300_Onine.dot –– Printed on 27.05.
TE2300 Version 1 Last Saved on 21.05.2003 10:18 HW Setup and Passwords TOSHIBA TE2300 8. Chapter 8 Optional Devices Optional devices can expand the computer’s capabilities and its versatility.
TE2300 Version 1 Last Saved on 21.05.2003 10:18 Optional Devices PC cards The computer is equipped with a PC card expansion slot that can accommodate two 5 mm Type II cards or one 10.5 mm Type III card. Any PC card that meets industry standards (manufactured by TOSHIBA or other vendor) can be installed. The slots support 16-bit PC cards, including PC card 16’s multifunction card and CardBus PC cards. CardBus supports the new standard of 32-bit PC cards.
TE2300 Version 1 Last Saved on 21.05.2003 10:18 Optional Devices Removing a PC card To remove the PC card, follow the steps below. 1. 2. 3. 4. Open the Safety Remove Hardware icon on the system tray and disable the PC card. Press the eject button of the PC card you want to remove to extend the button. Press the extended eject button to pop the card out slightly. Grasp the PC card and remove it.
TE2300 Version 1 Last Saved on 21.05.2003 10:18 Optional Devices 1. If you use the computer for a long time, the memory modules will become hot. In this case, let the memory modules cool to room temperature before you replace them. 2. Do not try to install a memory module with the computer turned on or turned off in Standby and Hibernation mode. You can damage the computer and the memory module. 3.
TE2300 Version 1 Last Saved on 21.05.2003 10:18 Optional Devices Inserting the memory module 8. 9. Seat the cover and secure it with one screw. When you turn the computer on, it should automatically recognize the total memory capacity. Use the HW Setup program to verify that the added memory is recognized. If it is not recognized, check the module’s connection. Removing memory module To remove the memory module, make sure the computer is in boot mode then: 1.
TE2300 Version 1 Last Saved on 21.05.2003 10:18 Optional Devices Removing the memory module 7. Seat the cover and secure it with one screw. Additional battery pack You can increase the portability of the computer with additional battery packs (PA3286*). If you’re away from an AC power source, you can replace a low battery with a fully charged one. See Chapter 6, Power and Power-Up Modes.
TE2300 Version 1 Last Saved on 21.05.2003 10:18 Optional Devices Opening the lid 2. Insert the HDD and push forward to ensure a firm connection. Installing the HDD 3. Close the lid and slide the lock to the lock position. TOSHIBA TE2300 8-7 ENGLISH using TE2300_Onine.dot –– Printed on 27.05.
TE2300 Version 1 Last Saved on 21.05.2003 10:18 Optional Devices Closing the lid For details on installing the Slim Select Bay HDD adaptor in the Slim Select Bay, refer to Chapter 4, Operating Basics. USB FDD Kit The 3 1/2" external FDD drive module can be connected to the USB port. For details on connecting the 3 1/2" external diskette drive module, refer to Chapter 4, Operating Basics.
TE2300 Version 1 Last Saved on 21.05.2003 10:18 Optional Devices ■ ■ ■ ■ ■ Security lock slot Audio line-in, line-out jacks Universal Serial Bus (two) ports i.LINK (IEEE 1394) port (This port is not supported by the computer.) DVI port (This port is not supported by the computer.) 1. When a Port Replicator is connected to the computer, remove all cables connected to the computer. 2. The TE2300 does not support the DVI and i.LINK ports on the Advanced Port Replicator II.
TE2300 Version 1 Last Saved on 21.05.2003 10:18 Optional Devices External monitor An external analog monitor can be connected to the external monitor port on the computer, Port Replicator. The computer supports VGA and Super VGA video modes. To connect a monitor, follow the steps below. If an external monitor is connected to the computer, do not connect the Port Replicator. First disconnect the external monitor from the computer then connect the Port Replicator and use its external monitor port.
TE2300 Version 1 Last Saved on 21.05.2003 10:18 Optional Devices Television A television can be connected to the video out port on the computer. To connect a television, follow the steps below. 1. 2. Turn the computer off. Use a video cable (not supplied) to connect the television to the video out port. Connecting a television 3. 4. Turn the television on. Turn the computer on. PS/2 mouse Use the PS/2 keyboard/mouse port on the computer or optional Advanced Port Replicator to connect a PS/2 mouse.
TE2300 Version 1 Last Saved on 21.05.2003 10:18 Optional Devices To disconnect the mouse, turn off the computer and pull out the mouse connector. Consult your mouse manual for instructions on how to install necessary software. PS/2 keyboard Use the PS/2 keyboard/mouse port on the computer or optional Advanced Port Replicator to connect a PS/2 keyboard. When an external keyboard is connected, you can use both the external keyboard and the computer’s internal keyboard.
TOSHIBA TE2300 9. Chapter 9 Troubleshooting TOSHIBA designed the computer for durability. However, should problems occur, following the procedures in this chapter can help to determine the cause. All readers should become familiar with this chapter. Knowing what might go wrong can help prevent problems from occurring. Problem solving process Resolving problems will be much easier if you observe the following guidelines: ■ Stop immediately when you recognize a problem exists.
TE2300 Version 1 Last Saved on 21.05.2003 10:18 Troubleshooting ■ Make sure all options are set properly in the setup program. ■ Check all cables. Are they correctly and firmly attached? Loose cables can cause signal errors. ■ Inspect all connecting cables for loose wires and all connectors for loose pins. ■ Check that your diskette is correctly inserted and that the diskette’s write protect tab is correctly set. Make notes of your observations and keep them in a permanent error log.
TE2300 Version 1 Last Saved on 21.05.2003 10:18 Troubleshooting Hardware If you cannot find a software problem, check your hardware. First run through the items in the preliminary checklist above. If you still cannot correct the problem, try to identify the source. The next section provides checklists for individual components and peripherals. Hardware and system checklist This section discusses problems caused by your computer’s hardware or attached peripherals.
TE2300 Version 1 Last Saved on 21.05.2003 10:18 Troubleshooting If any of the following conditions are present, the self test failed: ■ The computer stops and does not proceed to display information or messages. ■ A beep sounds, and after a few seconds no new messages appear. ■ Random characters appear on the screen, and the system does not function normally. ■ The screen displays an error message. Turn off the computer and check all cable connections. If the test fails again, contact your dealer.
TE2300 Version 1 Last Saved on 21.05.2003 10:18 Troubleshooting AC power If you have trouble turning on the computer with the AC adaptor connected, check the DC IN indicator. Refer to Chapter 6, Power and Power-Up Modes for more information. Problem Procedure AC adaptor doesn’t power the computer DC IN indicator does not glow green) Check the connections. Make sure the cord is firmly connected to the computer and a power outlet. Check the condition of the cord and terminals.
TE2300 Version 1 Last Saved on 21.05.2003 10:18 Troubleshooting Unplug the AC adaptor and remove the battery to make sure the terminals are clean. If necessary wipe them with a soft dry cloth dipped in alcohol. Connect the AC adaptor and replace the battery. Make sure it is securely seated. Check the Battery indicator. If it does not glow, let the computer charge the battery for at least 20 minutes.
TE2300 Version 1 Last Saved on 21.05.2003 10:18 Troubleshooting LCD panel Apparent LCD problems may be related to the computer’s setup. Refer to Chapter 7, HW Setup and Passwords, for more information. Problem Procedure No display Press hotkeys Fn + F5 to change the display priority, to make sure it is not set for an external monitor. Markings appear on the They might have come from contact with the LCD keyboard or AccuPoint II. Try wiping the LCD gently with a clean dry cloth.
TE2300 Version 1 Last Saved on 21.05.2003 10:18 Troubleshooting DVD-ROM drive For more information, refer to Chapter 4, Operating Basics. Problem Procedure You cannot access a DVD in the drive Make sure the drive’s drawer is securely closed. Press gently until it clicks into place. Open the drawer and make sure the DVD is properly seated. It should lie flat with the label facing up. A foreign object in the drawer could block laser light from reading the DVD. Make sure there is no obstruction.
TE2300 Version 1 Last Saved on 21.05.2003 10:18 Troubleshooting CD-RW/DVD-ROM drive For more information, refer to Chapter 4, Operating Basics. Problem Procedure You cannot access a Make sure the drive’s drawer is securely closed. CD or DVD in the drive Press gently until it clicks into place. Open the drawer and make sure the CD or DVD is properly seated. It should lie flat with the label facing up. A foreign object in the drawer could block laser light from reading the CD or DVD.
TE2300 Version 1 Last Saved on 21.05.2003 10:18 Troubleshooting Cannot write correctly If you have trouble writing, make sure you are observing the following precautions : ■ Use only media recommended by TOSHIBA ■ Do not use the mouse or keyboard during writing. ■ Use only the software supplied with the computer for recording. ■ Do not run or start other software during writing. ■ Do not jar the computer during writing.
TE2300 Version 1 Last Saved on 21.05.2003 10:18 Troubleshooting Infrared port Refer also to the documentation for your IrDA compatible device and related software. Problem Procedure Infrared devices do not Check that the device is connected to an electric work as expected outlet. Make sure the outlet is supplying power by plugging in an appliance. Make sure there is no obstruction blocking communication between the computer and the target device. If problems persist, contact your dealer.
TE2300 Version 1 Last Saved on 21.05.2003 10:18 Troubleshooting AccuPoint II Problem Procedure On-screen pointer does not respond to AccuPoint II operation The system might be busy. If the pointer is shaped as an hourglass, waitfor it to resum its normal shape and try again to move it. If a PS/2 or serial mouse is connected, check the HW Setup window. The Pointing Device option should be set to Simultaneous to use both the AccuPoint II and an external PS/2 mouse.
TE2300 Version 1 Last Saved on 21.05.2003 10:18 Troubleshooting Serial mouse ® This section applies only with Windows XP operating systems. ® You cannot use a serial mouse with Windows 2000. Problem Procedure On-screen pointer Check for a firm connection between the does not respond to computer’s serial port and the cable’s 9-pin serial mouse operation connector.
TE2300 Version 1 Last Saved on 21.05.2003 10:18 Troubleshooting PC card Refer also to Chapter 8, Optional Devices. Problem Procedure PC card error occurs Reseat the PC card to make sure it is firmly connected. Make sure the connection between the external device and the card is firm. Check the card’s documentation. If problems persist, contact your dealer. Monitor Refer also to Chapter 8, Optional Devices, and to your monitor’s documentation.
TE2300 Version 1 Last Saved on 21.05.2003 10:18 Troubleshooting Check Windows Device Manager. Make sure the sound function is enabled and that settings for I/O address, Interrupt level and DMA are correct for your software and do not conflict with other hardware devices that you may have connected to the computer. If problems persist, contact your dealer. TV output signal Refer also to your Personal Conferencing Kit’s documentation.
TE2300 Version 1 Last Saved on 21.05.2003 10:18 Troubleshooting Modem Problem Procedure Communication software can't initialize modem Make sure the computer’s internal modem settings are correct. Refer to Phone and Modem Options in the Control Panel. You can hear a dial tone but can't make a call If the call is going through a PBX machine, make sure the communication application’s tone dial detection feature is disabled.
TE2300 Version 1 Last Saved on 21.05.2003 10:18 Troubleshooting Standby/Hibernation Problem Procedure The system will not enter Standby/Hibernation Is Windows Media™ Player open? The system might not enter Standby/Hibernation, if Windows Media Player is either playing a selection or finished playing a selection. Close Windows Media Player before you select Standby/Hibernation. If problems persist, contact your dealer.
TE2300 Version 1 Last Saved on 21.05.2003 10:18 Troubleshooting TOSHIBA support If you require any additional help using your computer or if you are having problems operating the computer, you may need to contact TOSHIBA for additional technical assistance. Before you call Some problems you experience may be related to software or the operating system, it is important to investigate other sources of assistance first.
TE2300 Version 1 Last Saved on 21.05.2003 10:04 Specifications TOSHIBA TE2300 A. Appendix A Specifications This appendix summarizes the computer’s technical specifications. Physical Dimensions Size 316 (w) x 275(d) x 33.9 (front)/38.1 (back) millimeters (does not include the thicker part of the bottom of the computer) Weight (typical*) 2.7kilograms (Approximate), configured with: 14"XGA display, fixed DVD-ROM drive, 256MB memory, 40GB(5400rpm) HDD.
TE2300 Version 1 Last Saved on 21.05.2003 10:04 Specifications Built-in Modem Network control unit (NCU) Type of NCU AA Type of line Telephone line (analog only) Type of dialing Pulse Tone Control command AT commands EIA-578 commands Monitor function Computer’s speaker Communication specifications Communication system Data: Fax: Full duplex Half duplex Communication protocol Data ITU-T-Rec (Former CCITT) Bell V.21/V.22/V.22bis/V.32 /V.32bis/V.34/V.
TE2300 Version 1 Last Saved on 21.05.2003 10:04 Specifications TOSHIBA TE2300 B. Appendix B AC Power Cord and Connectors The power cord’s AC input plug must be compatible with the various international AC power outlets and the cord must meet the standards for the country/region in which it is used. All cords must meet the following specifications: Length: Minimum 2 meters Wire size: Minimum 0.75 mm Current rating: Minimum 2.
TE2300 Version 1 Last Saved on 21.05.2003 10:04 AC Power Cord and Connectors For the United States and Canada, plug configuration must be a 2-15P (250 V) or 1-15P (125 V) as designated in the U.S. National Electrical code handbook and the Canadian Electrical Code Part II. The following illustrations show the plug shapes for the U.S.A. and Canada, the United Kingdom, Australia and Europe.
TE2300 Version 1 Last Saved on 21.05.2003 10:04 AC Power Cord and Connectors TOSHIBA TE2300 C. Appendix C The TOSHIBA International Warranty The TOSHIBA International Warranty is a service policy on the parts and repair on your TOSHIBA portable personal computer which is automatically available to purchasers of the computer. The cover is assured in major industrial countries of the world.
TE2300 Version 1 Last Saved on 21.05.2003 10:04 The TOSHIBA International Warranty TOSHIBA's Worldwide Computer Representatives Australia Toshiba (Australia) Pty. Limited 84-92 Talavera Road, North Ryde NSW 2113 Tel: +61-2-9887-3322 Fax: +61-2-9888-3664 http://www.isd.toshiba.com.au Austria Toshiba Europe GmbH Leibnizstr. 2 93055 Regensburg Tel: 0800-29 74 88 Fax:+49-(0)941-780 79 25 www.computer.toshiba.at Azerbaijan AZEL (Azerbaijan Electronics) Floor 5, 65 Fizuli Str.
TE2300 Version 1 Last Saved on 21.05.2003 10:04 The TOSHIBA International Warranty Greece Ideal Electronics S.A. 25 Kreontos Str. 10442 Sepolia, Athens Tel: +30-210-5193950 Fax: +30-210-5193960 http://www.ideal.gr Hungary Technotrade Informatikai Rt. Öv u, 185, 1147 Budapest Tel: +36-1-467 6100 Fax: +36-1-252 6470 http://www.technotrade.hu Ireland Toshiba Information Systems (U.K.) Limited, Toshiba Court, Weybridge Business Park, Addlestone Road, Weybridge, Surrey KT15 2UL Tel.
TE2300 Version 1 Last Saved on 21.05.2003 10:04 The TOSHIBA International Warranty Netherlands Toshiba Information Systems Benelux B.V. Rivium Boulevard 41 2909 LK Capelle a/d IJssel Tel: +31-0900-1000-1000 Fax: +31-10-2882-390 http://www.toshiba.nl Norway Scribona Norway A/S Stålfjæra 20, P.O.Box 51, Kalbakken 0901 Oslo Tel: +47-22-897-189 Fax: +47-22-897-166 http://www.toshiba.se Oman (Sultanate of Oman) Suhail&Saud Bahwan (SSB) Sarco Building, Ground Floor No. 459, Way No.
TE2300 Version 1 Last Saved on 21.05.2003 10:04 The TOSHIBA International Warranty Slovenia Inea d.o.o. Stegne 11, 1000 Ljubljana Tel: +386-1-513-81-00 Fax: +386-1-513-81-60 http://www.inea.si South Africa CS IT Solutions, CS Holdings Office Park Block D, 241 Third Road PO Box 786691 1685 Midrand Tel: +27 (0) 11 205-7000 Fax: +27-0-11-205-8586 http://www.cs.co.za/it.htm. South Africa RECTRON (Pty) Ltd.
TE2300 Version 1 Last Saved on 21.05.2003 10:04 The TOSHIBA International Warranty Or for all countries not listed, please call the Toshiba International Service Line: or E-mail: toshibawarranty@nl.unisys.com Tel: +352 460433 Fax: +31-20-488 7654 TOSHIBA addresses for the Internet/World Wide Web TOSHIBA Europe http://www.toshiba-europe.com TOSHIBA Japan http://www.toshiba.co.jp TOSHIBA America http://www.toshiba.com TOSHIBA Canada http://www.toshiba.ca TOSHIBA TE2300 C-6 ENGLISH using TE2300_Onine.
TE2300 Version 1 Last Saved on 21.05.2003 10:04 The TOSHIBA International Warranty TOSHIBA TE2300 D. Appendix D Keyboard Layouts Arabic Belgian User’s Manual D-1 TOSHIBA TE2300 D-2 ENGLISH using TE2300_Onine.dot –– Printed on 27.05.
TE2300 Version 1 Last Saved on 21.05.2003 10:04 Keyboard Layouts Danish French German TOSHIBA TE2300 D-2 ENGLISH using TE2300_Onine.dot –– Printed on 27.05.
TE2300 Version 1 Last Saved on 21.05.2003 10:04 Keyboard Layouts Greek Hebrew Italian TOSHIBA TE2300 D-3 ENGLISH using TE2300_Onine.dot –– Printed on 27.05.
TE2300 Version 1 Last Saved on 21.05.2003 10:04 Keyboard Layouts Norwegian Polish Portuguese TOSHIBA TE2300 D-4 ENGLISH using TE2300_Onine.dot –– Printed on 27.05.
TE2300 Version 1 Last Saved on 21.05.2003 10:04 Keyboard Layouts Russian Spanish Swedish TOSHIBA TE2300 D-5 ENGLISH using TE2300_Onine.dot –– Printed on 27.05.
TE2300 Version 1 Last Saved on 21.05.2003 10:04 Keyboard Layouts Swiss-German Turkish UK English TOSHIBA TE2300 D-6 ENGLISH using TE2300_Onine.dot –– Printed on 27.05.
TE2300 Version 1 Last Saved on 21.05.2003 10:04 Keyboard Layouts US English TOSHIBA TE2300 D-7 ENGLISH using TE2300_Onine.dot –– Printed on 27.05.
TE2300 Version 1 Last Saved on 21.05.2003 10:04 Keyboard Layouts TOSHIBA TE2300 E. Appendix E Display Controller and Modes Display controller The display controller interprets software commands into hardware commands that turn particular pels on or off. The controller is an advanced Video Graphics Array (VGA) that provides Super VGA (SVGA) and Extended Graphics Array (XGA) support for the internal LCD and external monitors.
TE2300 Version 1 Last Saved on 21.05.2003 10:04 Display Controller and Modes Display modes This appendix is a table of the display mode options of your computer's Graphics and Memory Controller Hub.
TE2300 Version 1 Last Saved on 21.05.2003 10:04 Display Controller and Modes TOSHIBA TE2300 F. Appendix F If your computer is stolen Always take care of your computer and try to prevent it from being stolen. You are the owner of a valuable technical device, which may be highly attractive to thieves, so please do not leave it unattended in a public place. To further help protect against theft, security cables can be bought for use with your notebook when it is being used at home or in the office.
TE2300 Version 1 Last Saved on 21.05.2003 10:04 If your computer is stolen Toshiba Theft Registration Send to: Fax number: Toshiba Europe GmbH Technical Service and Support Leibnizstr. 2 93055 Regensburg Germany +49 (0) 941 7807 925 Country stolen: Machine type: (e.g. TOSHIBA TE2300) Model number: (e.g. PT230E YXT) Serial number: (e.g. 70123456E) Date stolen: Warranty seal: (e.g.
TE2300 Version 1 Last Saved on 21.05.2003 10:04 If your computer is stolen TOSHIBA TE2300 G. Appendix G Internal Modem Guide This appendix describes how to install and the remove the internal modem. Do not disassemble the computer beyond the steps described in this instruction or touch any components not specifically described. Installing the modem board The internal modem is preinstalled. The following is for information only. To install the modem board, follow the steps below. 1.
TE2300 Version 1 Last Saved on 21.05.2003 10:04 Internal Modem Guide Removing the modem board To remove the internal modem. 1. Save your data, quit Windows and turn off the power. 2. Disconnect the AC adaptor and any other peripheral devices. 3. Turn the computer upside down and remove the battery pack. 4. Remove one screw securing the modem cover and remove the cover. 5. Remove two screws securing the modem board. 6. Lift out the modem board. 7. Disconnect the modem board cable. 8.
TE2300 Version 1 Last Saved on 21.05.2003 10:04 Internal Modem Guide TOSHIBA TE2300 H. Appendix H ASCII Character Codes This appendix shows the American Standard Code for Information Interchange (ASCII) on the following pages. The characters in the IBM char column appear on your display when you type the corresponding ASCII code (as described in Chapter 5, The Keyboard). The characters that are printed, however, depend on the software you are using.
TE2300 Version 1 Last Saved on 21.05.
TE2300 Version 1 Last Saved on 21.05.2003 10:04 ASCII Character Codes Dec code Hex code IBM char Sort seq Dec code Hex code IBM char Sort seq 032 033 034 035 036 037 038 039 040 041 042 043 044 045 046 047 048 049 050 051 052 053 054 055 056 057 058 059 060 061 062 063 20 21 22 23 24 25 26 27 28 29 2A 2B 2C 2D 2E 2F 30 31 32 33 34 35 36 37 38 39 3A 3B 3C 3D 3E 3F space ! “ # $ % & ’ ( ) * + , .
TE2300 Version 1 Last Saved on 21.05.
TE2300 Version 1 Last Saved on 21.05.
TE2300 Version 1 Last Saved on 21.05.2003 10:04 ASCII Character Codes Dec code Hex code IBM char 224 225 226 227 228 229 230 231 232 233 234 235 236 237 238 239 240 241 242 243 244 245 246 247 248 249 250 251 252 253 254 255 E0 E1 E2 E3 E4 E5 E6 E7 E8 E9 EA EB EC ED EE EF F0 F1 F2 F3 F4 F5 F6 F7 F8 F9 FA FB FC FD FE FF α ß Γ Π ∑ σ µ ϒ Φ Θ Ω δ ϕ φ Ε Λ Ξ ± ≥ ≤ ⌠ ⌡ ÷ ≈ Sort seq 83 ° √ η 2 TOSHIBA TE2300 H-6 ENGLISH using TE2300_Onine.dot –– Printed on 27.05.
TE2300 Version 1 Last Saved on 21.05.2003 10:04 ASCII Character Codes TOSHIBA TE2300 I. Appendix I Wireless LAN This appendix is intended to help you get your Wireless LAN network up and running, with a minimum of parameters. Card specifications Form Factor ■ Mini PCI TypeIII Capability ■ IEEE 802.
TE2300 Version 1 Last Saved on 21.05.2003 10:04 Wireless LAN Refer to the sheet Information to the User for regulatory information that may apply in your country/region. R-F Frequency ■ Band 5 GHz (5150-5850 MHz) (Revision A, Turbo Mode) ■ Band 2.4 GHz (2400-2483.
TE2300 Version 1 Last Saved on 21.05.2003 10:04 Wireless LAN When installing Wireless LAN cards, the channel configuration is managed as follows: ■ For wireless clients that operate in a Wireless LAN Infrastructure, the Wireless LAN card will automatically start operation at the channel identified by the Wireless LAN Access Point. When roaming between different access points the station can dynamically switch to another channel if required.
TOSHIBA TE2300 Glossary The terms in this glossary cover the topics discussed in this manual. Alternate naming is included for reference.
TE2300 Version 1 Last Saved on 21.05.
TE2300 Version 1 Last Saved on 21.05.2003 10:04 Glossary A AccuPoint II: A pointing device integrated into the TOSHIBA computer keyboard. adapter: A device that provides an interface between two dissimilar electronic devices. For example, the AC adapter modifies the power from a wall outlet for use by the computer. This term also refers to the add-in circuit cards that control external devices, such as video monitors and magnetic tape devices. allocate: To assign a space or function for a specific task.
TE2300 Version 1 Last Saved on 21.05.2003 10:04 Glossary binary: The base two number system composed of zeros and ones (off or on), used by most digital computers. The right most digit of a binary number has a value of 1, the next a value of 2, then 4, 8, 16, and so on. For example, the binary number 101 has a value of 5. See also ASCII. BIOS: Basic Input Output System. The firmware that controls data flow within the computer. See also firmware.
TE2300 Version 1 Last Saved on 21.05.2003 10:04 Glossary Centronics: The printer manufacturer whose method of data transmission between a parallel printer and a computer has become an industry standard. CGA: Color/graphics adapter. A video display protocol defined by the IBM Color/Graphics Monitor Adapter and its associated circuitry. This protocol supports two-color 640x200 and four-color 320x200 graphics, and 16-color 640x200 and 320x200 text modes.
TE2300 Version 1 Last Saved on 21.05.2003 10:04 Glossary CPS: Characters per second. Typically used to indicate the transmission speed of a printer. CPU: Central processing unit. The portion of the computer that interprets and executes instructions. CRT: Cathode Ray Tube. A vacuum tube in which beams projected on a fluorescent screen-producing luminous spots. An example is the television set. cursor: A small, blinking rectangle or line that indicates the current position on the display screen.
TE2300 Version 1 Last Saved on 21.05.2003 10:04 Glossary documentation: The set of manual and/or other instructions written for the users of a computer system or application. Computer system documentation typically includes procedural and tutorial information as well as system functions. DOS: Disk operating system. See operating system. driver: A software program, generally part of the operating system, that controls a specific piece of hardware (frequently a peripheral device such as a printer or mouse).
TE2300 Version 1 Last Saved on 21.05.2003 10:04 Glossary floppy disk drive (FDD): See diskette drive. Fn-esse: A TOSHIBA utility that lets you assign functions to hotkeys. format: The process of readying a blank disk for its first use. Formatting establishes the structure of the disk that the operating system expects before it writes files or programs onto the disk. folder: An icon in Windows used to store documents or other folders.
TE2300 Version 1 Last Saved on 21.05.2003 10:04 Glossary iLINK (IEEE1394): This port enables high-speed data transfer directly from external devices such as digital video cameras. infrared port: A cableless communications capable of using infrared signals to send serial data. input: The data or instructions you provide to a computer, communication device or other peripheral device from the keyboard or external or internal storage devices.
TE2300 Version 1 Last Saved on 21.05.2003 10:04 Glossary L level 2 cache: See cache. Light Emitting Diode (LED): A semiconductor device that emits light when a current is applied. Liquid Crystal Display (LCD): Liquid crystal sealed between two sheets of glass coated with transparent conducting material. The viewingside coating is etched into character forming segments with leads that extend to the edge of the glass.
TE2300 Version 1 Last Saved on 21.05.2003 10:04 Glossary motherboard: A name sometimes used to refer to the main printed circuit board in processing equipment. It usually contains integrated circuits that perform the processor’s basic functions and provides connectors for adding other boards that perform special functions. Sometimes called a main board. MPEG: Moving picture coding expert group is an industry standard architecture for compression of video signals.
TE2300 Version 1 Last Saved on 21.05.2003 10:04 Glossary P parallel: Refers to two or more processes or events that can occur simultaneously, and without interfering with each other. See also serial. parallel interface: Refers to a type of information exchange that transmits information one byte (8 bits) at a time. See also serial interface. parity: 1) The symmetrical relationship between two parameter values (integers) both of which are either on or off; odd or even; 0 or 1.
TE2300 Version 1 Last Saved on 21.05.2003 10:04 Glossary R Radio frequency interference (RFI) shield: A metal shield enclosing the printed circuit boards of the printer or computer to prevent radio and TV interference. All computer equipment generates radio frequency signals. The FCC regulates the amount of signals a computing device can allow past its shielding. A Class A device is sufficient for office use. Class B provides a more stringent classification for home equipment use.
TE2300 Version 1 Last Saved on 21.05.2003 10:04 Glossary soft key: Key combinations that emulate keys on the IBM keyboard, change some configuration options, stop program execution, and access the numeric keypad overlay. software: The set of programs, procedures and related documentation associated with a computer system. Specifically refers to computer programs that direct and control the computer system’s activities. See also hardware.
TE2300 Version 1 Last Saved on 21.05.2003 10:04 Glossary W Warm dock/undock: Connecting or disconnecting a device to or from the computer while the computer is suspended. warm start: Restarting or resetting a computer without turning it off. window: A portion of the screen that can display its own application or document. Often used to mean a Microsoft Windows window.
TE2300 Version 1 Last Saved on 21.05.2003 10:04 Glossary TOSHIBA TE2300 1.
TE2300 Version 1 Last Saved on 21.05.
TE2300 Version 1 Last Saved on 21.05.
