User’s Manual M1 User’s Manual Tecra M1 *T201879-EN* T201879-EN TECRAM1 TECRAM1 TECRAM1 TECRAM1 TECRAM1 TECRAM1 TECRAM1 TECRAM1 Choose freedom. computers.toshiba-europe.com Choose freedom. computers.toshiba-europe.
TECRA M1 Version 1 Last Saved on 24.02.2003 11:06 Tecra M1 Copyright © 2003 by TOSHIBA Corporation. All rights reserved. Under the copyright laws, this manual cannot be reproduced in any form without the prior written permission of TOSHIBA. No patent liability is assumed, with respect to the use of the information contained herein.
TECRA M1 Version 1 Last Saved on 24.02.2003 11:06 Tecra M1 EU Declaration of Conformity TOSHIBA declares, that the product: PT930* conforms to the following Standards: Supplementary Information: “The product complies with the requirements of the Low Voltage Directive 73/23/EEC, the EMC Directive 89/336/EEC and/or the R&TTE Directive 1999/05/EEC.” This product is carrying the CE-Mark in accordance with the related European Directives.
TECRA M1 Version 1 Last Saved on 24.02.2003 11:06 Tecra M1 Modem warning notice Conformity Statement The equipment has been approved to [Commission Decision “CTR21”] for pan-European single terminal connection to the Public Switched Telephone Network (PSTN). However, due to differences between the individual PSTNs provided in different countries/regions the approval does not, of itself, give an unconditional assurance of successful operation on every PSTN network termination point.
TECRA M1 Version 1 Last Saved on 24.02.2003 11:06 Tecra M1 Description on Laser specification The optical drive such as CD-ROM drive, CD-RW drive, DVD-ROM drive, DVD/CD-RW drive and DVD Multi drive that is used in this computer is equipped with laser. The classification label with the following sentence is affixed to the surface of the drive.
Tecra M1 1. General Precautions TOSHIBA computers are designed to optimize safety, minimize strain and withstand the rigors of portability. However, certain precautions should be observed to further reduce the risk of personal injury or damage to the computer. Be certain to read the general precautions below and to note the cautions included in the text of the manual. Stress injury Carefully read the Safety Instruction Manual.
TECRA M1 Version 1 Last Saved on 22.02.2003 11:16 General Precautions Central Processing Unit ("CPU") Performance Disclaimer CPU Performance in your computer product may vary from specifications under the following conditions: 1. use of certain peripheral products 2. use of battery power instead of AC power 3. use of certain multimedia games or videos with special effects 4. use of standard telephone lines or low speed network connections 5.
Tecra M1 Table of Contents General Precautions Preface Manual contents ........................................................................... xii Conventions..................................................................................xiii Chapter 1: Introduction Equipment checklist.....................................................................1-1 Features .......................................................................................1-2 Special features ............................
TECRA M1 Version 1 Last Saved on 22.02.2003 11:24 Table of Contents Restarting the computer ............................................................3-13 Restoring the preinstalled software from the Product Recovery CD-ROM ....................................................................3-13 Chapter 4: Operating Basics TOSHIBA Dual Pointing Device ...................................................4-1 Using the USB diskette drive.......................................................
TECRA M1 Version 1 Last Saved on 22.02.2003 11:24 Table of Contents SD cards ......................................................................................8-5 Memory expansion ......................................................................8-8 Hard disk drive pack ..................................................................8-14 Additional battery pack ..............................................................8-16 Slim Select Bay 2nd battery pack.....................................
Tecra M1 1. Preface Congratulations on your purchase of the Tecra M1 Series computer. This powerful notebook computer provides excellent expansion capability, including multimedia devices, and it is designed to provide years of reliable, high-performance computing. This manual tells how to set up and begin using your Tecra M1 Series computer. It also provides detailed information on configuring your computer, basic operations and care, using optional devices and troubleshooting.
Tecra M1 Version 1 Last Saved on 24.02.2003 11:09 Preface Manual contents This manual offers important information about your computer, including solutions to the most common problems, and features and specifications. Refer to the online manual preinstalled on your system for the details. To open the online manual, follow either one of the steps below: 1. From Desktop, click Start, point to All programs, click TOSHIBA User’s Manual. 2. From Desktop, click TOSHIBA User’s Manual icon.
Tecra M1 Version 1 Last Saved on 24.02.2003 11:09 Preface Conventions This manual uses the following formats to describe, identify, and highlight terms and operating procedures. Abbreviations On first appearance, and whenever necessary for clarity, abbreviations are enclosed in parentheses following their definition. For example: Read Only Memory (ROM). Acronyms are also defined in the Glossary. Icons Icons identify ports, dials, and other parts of your computer.
Tecra M1 Version 1 Last Saved on 24.02.2003 11:09 Preface Key operation Some operations require you to simultaneously use two or more keys. We identify such operations by the key top symbols separated by a plus sign (+). For example, Ctrl + C means you must hold down Ctrl and at the same time press C. If three keys are used, hold down the first two and at the same time press the third.
Tecra M1 1. Chapter 1 Introduction This chapter provides an equipment checklist, and it identifies the computer’s features, options and accessories. Some of the features described in this manual may not function properly if you use an operating system that was not preinstalled by TOSHIBA. Equipment checklist Carefully unpack your computer. Save the box and packing materials for future use.
TECRA M1 Version 1 Last Saved on 24.02.
TECRA M1 Version 1 Last Saved on 24.02.2003 11:10 Introduction Memory Slots 128, 256, 512 or 1,024 MB memory modules can be installed in the two memory slots for a maximum of 2,048 MB system memory. Video RAM 32 MB or 64 MB of RAM is provided for video display. Power Battery pack The computer is powered by one rechargeable lithium-ion battery pack. RTC battery The computer has an internal battery to back up the internal Real Time Clock (RTC) and calendar.
TECRA M1 Version 1 Last Saved on 24.02.2003 11:10 Introduction CD-ROM drive A maximum 24-speed 640MB CD-ROM drive supports the following formats: • CD-ROM • CD-EXTRA • Photo CD • Audio CD • CD-ROMxA • CD-DA • CD-I • CD-Text • CD-R (read only) • CD-RW (read only) DVD-ROM drive Some models are equipped with a full-size, DVD-ROM drive module that lets you run either 12 cm (4.72") or 8 cm (3.15") CD/DVDs without using an adaptor. It runs DVD-ROMs at maximum 8 speed and CD-ROMs at maximum 24 speed.
TECRA M1 Version 1 Last Saved on 24.02.2003 11:10 Introduction DVD Multi drive Some models are equipped with a full-size DVD Multi drive module that lets you record data to rewritable CD/DVDs as well as run either 12cm (4.72") or 8cm (3.15") CD/DVDs without using an adaptor. An ATAPI interface controller is used for CD/DVD-ROM operation. The drive reads DVDs at maximum 8 speed and CDs at maximum 24 speed.
TECRA M1 Version 1 Last Saved on 24.02.2003 11:10 Introduction TOSHIBA Dual Pointing Device Built-in Touch Pad A Touch Pad and control buttons in the palm rest enable control of the on-screen pointer and scrolling of windows. Built-in AccuPoint This pointer control stick, located in the center of the keyboard, provides convenient control of the cursor. Ports Parallel Parallel printer or other parallel device (ECP compatible).
TECRA M1 Version 1 Last Saved on 24.02.2003 11:10 Introduction Multimedia Sound system Windows sound system compatible sound system provides internal speakers as well as jacks for an external microphone and headphone. Video-out jack (S-Video) This jack lets you transfer video data to external devices. Use the S Video cable for both videoout. Data output depends on the type of device connected to the S Video cable.
TECRA M1 Version 1 Last Saved on 24.02.2003 11:10 Introduction Wireless LAN Some computers in this series are equipped with a wireless LAN mini-PCI card that is compatible with other LAN systems based on Direct Sequence Spread Spectrum radio technology that complies with the IEEE 802.11 Standard (Revision B only), and IEEE 802.11 Standard (Revision A, B), and Turbo Mode. ■ Automatic Transmit Rate Select mechanism in the transmit range of 54, 48, 36, 24, 18, 12, 9 and 6 Mbit/s.
TECRA M1 Version 1 Last Saved on 24.02.2003 11:10 Introduction PC card lock A PC card can be secured by the PC card lock fixed with a lock screw in the PC card lock screw hole. Slim Select Bay lock Slim Select Bay module can be secured by Slim Select Bay lock fixed with a lock screw in the lock position. The lock screw is inserted in the unlock position when purchased. Software Standard Windows XP Professional operating system and TOSHIBA Utilities and drivers preinstalled on the hard disk.
TECRA M1 Version 1 Last Saved on 24.02.2003 11:10 Introduction System automatic Standby/ Hibernation This feature automatically shuts down the system in standby mode or Hibernation mode when there is no input or hardware access for a time specified. You can specify the time and select either System Standby or System Hibernate in the System standby and System hibernate item of the Power Save Mode window in TOSHIBA Power Saver. Keypad overlay A ten-key pad is integrated into the keyboard.
TECRA M1 Version 1 Last Saved on 24.02.2003 11:10 Introduction Hibernation This feature lets you turn off the power without exiting from your software. The contents of main memory is saved to the hard disk, when you turn on the power again, you can continue working right where you left off. Refer to the Turning off the power section in Chapter 3, Getting Started, for details. Standby If you have to interrupt your work, you can turn off the power without exiting from your software.
TECRA M1 Version 1 Last Saved on 24.02.2003 11:10 Introduction Drag’n Drop CD This easy-to-use software lets you record CDs with just a few mouse clicks. You can create CDs in several formats including audio CDs that can be played on a standard stereo CD player and data CDs to store the files and folders on your hard drive. This software can be used on a model with CD-RW/DVD-ROM drive or DVD Multi drive.
TECRA M1 Version 1 Last Saved on 24.02.2003 11:10 Introduction AC adaptor If you use your computer at more than one site frequently, it may be convenient to purchase an additional AC adaptor for each site so you will not have to carry the adaptor with you. Battery charger The battery charger lets you charge extra batteries outside the computer. Security lock A slot is available to attach a security cable to the computer to deter theft. USB FDD Kit A 3 1/2" diskette drive accommodates 1.
TECRA M1 Version 1 Last Saved on 24.02.2003 11:10 Introduction CD-ROM Refer to the Features section for details DVD-ROM Refer to the Features section for details. CD-RW/DVD-ROM Refer to the Features section for details. DVD Multi Refer to the Features section for details. Slim Select Bay HDD adaptor An adaptor lets you install an optional HDD described in Chapter 8, Optional Devices.
Tecra M1 2. Chapter 2 The Grand Tour This chapter identifies the various components of your computer. Become familiar with each component before you operate the computer. Front with the display closed Shows the computer’s front with its display panel in the closed position.
The Grand Tour Volume control Use this dial to adjust the volume of the stereo speakers and subwoofer or the stereo headphones. Off On Display latch This latch secures the LCD panel in its closed position. Slide the latch to open the display. Wireless communication switch Slide this switch toward the front of the computer to turn off Wireless LAN and Bluetooth functions. Slide it to the right to turn on the functions (Wireless model or Wireless LAN ready model only).
The Grand Tour SD card slot SD cards are used in a wide variety of external devices. This slot lets you transfer data from the device to your computer. An indicator on the left side of the slot glows when a card is being accessed. Keep foreign objects out of the SD card slot. A pin or similar object can damage the computer’s circuitry. PC card lock Slide this lock to release or secure PC cards. Security lock A security cable attaches to this slot.
The Grand Tour Right side Shows the computer’s right side. USB PORT 3 SLIM SELECT BAY The right side of the computer A third Universal Serial Bus (USB 2.0 compliant) port Universal Serial Bus (USB 2.0) port is on the right side. See Universal Serial Ports in the Left side section for details. However, the USB port 3 does not support USB KB/Mouse and USB FDD Legacy Emulation.
The Grand Tour Back side Shows the computer’s back panel. EXTERNAL MONITOR PORT DC IN 15V LAN ACTIVE INDICATOR (ORANGE) SERIAL PORT VIDEO OUT PARALLEL PORT LINK INDICATOR (GREEN) MODEM JACK LAN JACK COOLING VENTS I.LINK (IEEE 1394) PORT The back side of the computer Ether External monitor port This 15-pin port lets you connect an external video display. Serial port Use this 9-pin port to connect external serial devices such as an external modem, a serial mouse or printer.
The Grand Tour DC IN 15V The AC adaptor connects to this socket. Use only the model of AC adaptor that comes with the computer. Using the wrong adaptor can damage your computer. Video-out jack Plug an S-Video cable into this jack for video-out. The S-Video cable carries video signal. Modem jack In areas where an internal modem is installed as standard equipment, there is a modem jack that lets you use a modular cable to connect the modem directly to a telephone line. DC IN 15V 1.
The Grand Tour Underside Shows the underside of the computer. Make sure the display is closed before turning over your computer. DOCKING INTERFACE PC CARD LOCK SLIM SELECT BAY LOCK SLIM SELECT BAY NOTCHES SCREW HOLE COOLING FAN BATTERY PACK SLIM SELECT BAY LOCK SCREW BATTERY RELEASE LATCH HDD PACK COVER SCREW The underside of the computer Slim Select Bay See the Right side section in this chapter for details. Slim Select Bay lock Slide the lock to release or secure the Slim Select Bay ejector.
The Grand Tour Docking interface This port enables connection of an optional Advanced port Replicator II described in Chapter 8 Optional Devices. Keep foreign objects out of the docking interface port. A pin or similar object can damage the computer’s circuitry. A plastic shutter protects the connector. Notches Notches on the computer engage hooks on the Advanced port Replicator II to hold the connection securely. Battery pack The battery pack powers the computer when the AC adaptor is not connected.
The Grand Tour Front with the display open This section shows the computer with the display open. Refer to the appropriate illustration for details.
The Grand Tour Display screen The LCD displays high-contrast text and graphics. The computer’s LCD consists of up to 1024 x 768 pixels or 1400 x 1050 pixels. Refer to Appendix E. When the computer operates on the AC adaptor the display screen’s image will be somewhat brighter than when it operates on battery power. The lower brightness level is intended to save battery power. Press this button to launch an application TOSHIBA Console button automatically. The default is TOSHIBA Console.
The Grand Tour Microphone A built-in microphone lets you record sound into your applications. Refer to the Using the microphone section in Chapter 4, Operating Basics. Brightness Sensor The Brightness sensor adjusts the brightness of LCD to the adequate brightness according to the illuminance of the place where you are using the PC. The Brightness Sensor automatically adjusts the brightness of LCD display. However, you can compensate the brightness using TOSHIBA Brightness Sensor Control.
The Grand Tour System indicators LEDs beneath icons, light when various computer operations are in progress. DC IN 15V POWER BATTERY DISK SLIM WIRELESS SELECT BAY COMMUNICATION System indicators DC IN 15V The DC IN 15V indicator glows in green when DC power is supplied from the AC power adaptor. If the adaptor’s output voltage is abnormal or if the power supply malfunctions, this indicator flashes orange. Power The Power indicator glows in green when the computer is on.
The Grand Tour Keyboard indicators The figures below show the positions of the keypad overlay indicators and the CapsLock indicator. When the F10 key indicator glows the keypad overlay lets you control the cursor. When the F11 key indicator glows the keypad overlay lets you enter numbers. NUMERIC MODE INDICATOR ARROW MODE INDICATOR Keypad overlay indicators When the CapsLock indicator glows the keyboard is in all-caps mode.
The Grand Tour USB diskette drive (Provided with some models) A 3 1/2" diskette drive accommodates 1.44-megabyte or 720-kilobyte diskettes. It connects to the USB port. DISK-IN-USE INDICATOR EJECT BUTTON DISKETTE SLOT USB diskette drive Disk-In-Use Indicator This indicator lights when the diskette is being accessed. Diskette slot Insert a diskette in this slot. Eject button When a diskette is fully seated in the drive, the eject button pops out.
The Grand Tour Slim Select Bay modules The Slim Select Bay can accommodate the following modules: CD-ROM drive, DVD-ROM drive, CD-RW/DVD-ROM drive, DVD Multi drive, optional secondary battery pack and optional Slim Select Bay HDD adaptor. CD-ROM drive An optional full-size, maximum 24-speed CD-ROM drive module lets you run either 12 cm (4.72") or 8 cm (3.15") compact discs without using an adaptor. It may be selected as a standard component or as an option.
The Grand Tour DVD-ROM drive An optional full-size DVD-ROM drive module lets you run either 12 cm (4.72") or 8 cm (3.15") digital video disc/compact disc without using an adaptor. It may be selected as a standard component or as an option. The read speed is slower at the centre of a disc and faster at the outer edge.
The Grand Tour Code 1 2 3 4 5 6 Region Canada, United States Japan, Europe, South Africa, Middle East Southeast Asia, East Asia Australia, New Zealand, Pacific Islands, Central America, South America, Caribbean Russia, Indian Subcontinent, Africa, North Korea, Mongolia China CD-RW/DVD-ROM drive The full-size CD-RW/DVD-ROM drive module lets you record data to rewritable CDs as well as run either 12 cm (4.72") or 8 cm (3.15") CD/DVDs without using an adaptor.
The Grand Tour CD/DVD-In-Use Indicator This indicator lights when the CD/DVD is being accessed. Eject button Press the eject button to open the drawer partially. Eject hole Insert a slender object to open the drawer when the power to the computer is off. Check the Slim Select Bay indicator when you use the DVD-ROM drive. Do not press the eject button, disconnect a drive or turn off the computer while the light is glowing. Doing so could damage the DVD/CD or the drive.
The Grand Tour DVD read DVD-R write DVD-RW write DVD-RAM write CD read CD-R write CD-RW write 8 speed (maximum) 1 speed 1 speed 2 speed 24 speed (maximum) 16 speed (maximum) 8 speed (maximum) CD/DVD-IN-USE INDICATOR EJECT HOLE EJECT BUTTON The DVD Multi drive CD/DVD-In-Use Indicator This indicator lights when the CD/DVD is being accessed. Eject button Press the eject button to open the drawer partially. Eject hole Insert a slender object to open the drawer when the power to the computer is off.
The Grand Tour 4 5 6 Australia, New Zealand, Pacific Islands, Central America, South America, Caribbean Russia, Indian Subcontinent, Africa, North Korea, Mongolia China Use the WinDVD 4 application to view DVD-Video discs. CD-R and DVD-R discs can be written only once. The recorded data cannot be erased or changed. CD-RW describes discs that can be recorded more than once. Use either 1, 2, or 4 multi speed CD-RW discs or high-speed 4- to 10-speed discs.
The Grand Tour Unlock UNLOCK Lock LOCK The Slim Select Bay HDD adaptor 4. Slide the cover lock to the lock position. Weight saver module Installing a weight saver module in the Slim Select Bay lets you reduce the carrying weight of the computer. The weight saver module Tecra M1 2-21 ENGLISH using TecraM1online.dot –– Printed on 24.02.
The Grand Tour AC adaptor The AC adaptor converts AC power to DC power and reduces the voltage supplied to the computer. It can automatically adjust to any voltage from 100 to 240 volts and to a frequency of either 50 or 60 hertz, enabling you to use the computer in almost any country/region. To recharge the battery, simply connect the AC adaptor to a power source and the computer. See Chapter 6 Power and Power-Up Modes for details.
Tecra M1 3. Chapter 3 Getting Started This chapter provides basic information to get you started using your computer. It covers the following topics: ■ Setting up your work space — for your health and safety Be sure also to read the Safety Instruction Manual. This guide, which is included with the computer, explains product liability.
Getting Started Setting up your work space Establishing a comfortable work site is important for you and your computer. A poor work environment or stressful work habits can result in discomfort or serious injury from repetitive strain to your hands, wrists or other joints. Proper ambient conditions should also be maintained for the computer’s operation.
Getting Started General conditions In general, if you are comfortable, so is your computer, but read the following to make sure your work site provides a proper environment. ■ Make sure there is adequate space around the computer for proper ventilation. ■ Make sure the AC power cord connects to an outlet that is close to the computer and easily accessible. ■ The temperature should be 5 to 35 degrees Centigrade (41 to 95 degrees Fahrenheit) and the relative humidity should be 20 to 80 percent.
Getting Started Seating and posture The height of your chair in relation to the computer and keyboard as well as the support it gives your body are primary factors in reducing work strain. Refer to the following tips and to figure below. BELOW EYE LEVEL 90O ANGLES FOOT REST Posture and positioning of the computer ■ Place your chair so that the keyboard is at or slightly below the level of your elbow. You should be able to type comfortably with your shoulders relaxed.
Getting Started ■ If possible, use soft, indirect lighting in your computer work area. Use a lamp to illuminate your documents or desk, but be sure to position the lamp so that it does not reflect off the display or shine in your eyes. Work habits A key to avoiding discomfort or injury from repetitive strain is to vary your activities. If possible, schedule a variety of tasks into your work day.
Getting Started Connecting the AC adaptor Attach the AC adaptor when you need to charge the battery or you want to operate from AC power. It is also the fastest way to get started, because the battery pack will need to be charged before you can operate from battery power. The AC adaptor can be connected to any power source supplying from 100 to 240 volts and 50 or 60 hertz. For details on using the AC adaptor to charge the battery pack, refer to Chapter 6, Power and Power-Up Modes.
Getting Started Connecting the adaptor to the computer 3. Plug the power cord into a live wall outlet. The Battery and DC IN indicators on the front of the computer should glow. Tecra M1 3-7 ENGLISH using TecraM1online.dot –– Printed on 24.02.
Getting Started Opening the display The display panel can be rotated in a wide range of angles for optimal viewing. 1. Slide the display latch on the front of the computer to the right. 2. Lift the panel up and adjust it to the best viewing angle for you. Use reasonable care when opening and closing the display panel. Opening it vigorously or slamming it shut could damage the computer. DISPLAY LATCH Opening the display Tecra M1 3-8 ENGLISH using TecraM1online.dot –– Printed on 24.02.
Getting Started Turning on the power This section describes how to turn on the power. After you turn on the power for the first time, do not turn it off until you have set up the operating system. Refer to the section Starting up for the first time in this chapter. 1. Open the display. 2. Press and hold the computer’s power button for two or three seconds.
Getting Started 3. In Windows XP, click start then click Turn Off Computer. From the Turn Off Computer menu select Turn Off. 4. Turn off the power to any peripheral devices. Do not turn the computer or devices back on immediately. Wait a moment to let all capacitors fully discharge. Hibernation mode The hibernation feature saves the contents of memory to the hard disk when the computer is turned off. The next time the computer is turned on, the previous state is restored.
Getting Started Windows XP 1. Click start. 2. Select Turn Off Computer. 3. Open the Turn Off Computer dialog box. Hibernate is not displayed. 4. Press the Shift key. The Standby item will change to Hibernate. 5. Select the Hibernate. Automatic Hibernation The computer will enter Hibernate mode automatically when you press the power button or close the lid. First, however, make the appropriate settings according to the steps below. 1. Open the Control Panel. 2.
Getting Started ■ To restore operation, press the power button or press any key. The latter action works only if Wake-up on Keyboard is enabled in HW Setup. ■ If a network application is active when the computer automatically enters Standby, it might not be restored when the computer wakes up from standby. To prevent the computer from automatically entering standby mode, disable Standby in TOSHIBA Power Saver. Open the Standby setting.
Getting Started In Windows XP, open Performance and Maintenance and open TOSHIBA Power Saver. When you turn the power back on, you can continue where you left when you shut down the computer. 1. When the computer is shut down in standby mode, the power indicator flashes orange. 2. If you are operating the computer on battery power, you can lengthen the operating time by shutting down in hibernation mode. Standby mode consumes more power.
Getting Started 2. Hold down the F12 key and turn on the power. When the TOSHIBA logo appears, release the F12 key. 3. Use the left or right cursor key to select the CD-ROM icon in the display menu. For details, refer to the Boot priority section in Chapter 7, HW Setup. 4. Follow the on-screen instructions. 5. If your computer came with additional software installed, this software can not be recovered from the Recovery CD. Re-install these applications (e.g.
Tecra M1 4. Chapter 4 Operating Basics This chapter gives information on basic operations including using the TOSHIBA Dual Pointing Devices, USB diskette drive, the microphone, the internal modem, wireless communication, LAN, and changing Slim Select Bay modules. It also provides tips on caring for your computer, diskettes and CD/DVDs. TOSHIBA Dual Pointing Device The computer is equipped with a dual point system: a Touch Pad and an AccuPoint pointing stick.
Operating Basics You can also tap the Touch Pad to perform functions similar to those of the left button. Click: Tap the Touch Pad once Double-click: Tap twice Drag and drop: Tap to select the material you want to move. Leave your finger on the Touch Pad after the second tap and move the material. Using the AccuPoint To use the AccuPoint, simply push it with your finger tip in the direction you want to move the on-screen pointer.
Operating Basics Removing the AccuPoint cap 2. Position a new cap on the peg and press it into place. The peg is square, so be careful to align the cap’s square hole with the peg. Using the USB diskette drive A 3 1/2" diskette drive connects to the computer’s USB port. It accommodates 1.44-megabyte or 720-kilobyte diskettes. Refer to Chapter 2, Grand Tour, for more information. Connecting 3 1/2" diskette drive To connect the drive, plug the diskette drive connector into a USB port.
Operating Basics Connecting the USB diskette drive If you connect the diskette drive after turning on the computer, it will take about 10 seconds for the computer to recognize the drive. Do not disconnect and reconnect before 10 seconds has elapsed. Disconnecting 3 1/2" diskette drive When you have finished using the diskette drive, follow the procedures below to disconnect it: 1. Wait for the indicator light to go out to make sure all diskette activity has stopped.
Operating Basics 1. To avoid injury, do not put your hand into the Slim Select Bay slot. 2. Before removing or inserting a second battery pack, turn off the computer’s power. The TOSHIBA Mobile Extension is preinstalled to support hot swapping under Windows. Refer to Chapter 1, Introduction for information on using this utility to change modules while the computer’s power is on. Removing a module Remove the DVD-ROM drive as described below. 1. Check all disk indicators to make sure no disks are operating.
Operating Basics 2. If you want to lock the Slim Select Bay module, set the Slim Select Bay lock screw in the hole for the lock position. The lock screw is inserted in the unlock position at the time of purchasing. LOCK SCREW SLIM SELECT BAY MODULE LOCK POSITION Inserting the Slim Select Bay HDD adaptor Using optical media drives The text and illustrations in this section refer primarily to the Fixed DVDROM drive. However, operation is the same for other optical drive in the Slim Select Bay.
Operating Basics EJECT BUTTON Pressing the DVD-ROM eject button b. Pressing the eject button will not open the drawer when the DVDROM drive’s power is off. If the power is off, you can open the drawer by inserting a slender object (about 15 mm) such as a straightened paper clip into the eject hole just to the right of the eject button. Diameter 1.0 mm Manual release with the eject hole 2. Pinch the drawer gently and pull until it is fully opened. Pulling the drawer open 3.
Operating Basics Inserting a CD/DVD When the drawer is fully opened, the edge of the computer will extend slightly over the CD/DVD tray. Therefore, you will need to turn the CD/DVD at an angle when you place it in the tray. After seating the CD/DVD, however, make sure it lies flat, as shown in figure above. 1. Do not touch the laser lens. Doing so could cause misalignment. 2. Do not keep foreign matter from entering the drive.
Operating Basics Removing discs To remove the CD/DVD, follow the steps below and refer to figure below. Do not press the eject button while the computer is accessing the Fixed DVD-ROM drive. Wait for the Slim Select Bay indicator to go out before you open the drawer. Also, if the CD/DVD is spinning when you open the drawer, wait for it to stop before you remove it. 1. To pop the drawer partially open, press the eject button. Gently pull the drawer out until it is fully opened. 1.
Operating Basics Before writing or rewriting Please observe the following points when you write or rewrite the data. ■ We recommend the following manufacturers of CD-R and CD-RW media. Media quality can affect write or rewrite success rates. CD-R: TAIYOYUDEN CO., LTD. Mitsui Chemicals Inc. MITUBISHI CHEMICAL CORPORATION RICOH Co., Ltd. Hitachi Maxell Ltd. CD-RW: MITUBISHI CHEMICAL CORPORATION RICOH Co., Ltd. TOSHIBA has confirmed the operation of CD-R and CD-RW media of the manufacturers above.
Operating Basics ■ PC card, SD card, USB devices, external display, i.LINK devices, optical digital devices. ■ Use the CD/MP3 control buttons to reproduce music and voice. ■ Open the optical media drive. ■ If the media is poor in quality, dirty or damaged, writing or rewriting errors may occur. ■ Set the computer on a level surface and avoid places subject to vibration such as airplanes trains, or cars. Do not use an unstable surface such as a stand.
Operating Basics Read/write function chart Disc type Read Write 1 Drag’n Drop CD* 1 DVDfunSTUDIO* 1 DVD-MovieAlbum* 2 DVD-Video* CD-R CDRW DVDR DVDRW DVDRAM DVD +R DVD +RW Yes Yes Yes Yes Yes No No Yes Yes Yes Yes Yes No No Yes Yes Yes Yes Yes No No No No Yes Yes No No No No No No No Yes No No No No Yes Yes No No No No No No No Yes No No 2 DVD VR* (DVD VideoRecording) 1 * Software supplied with the product can be used for writing to a disc.
Operating Basics ■ There are two types of DVD discs: authoring and general use discs. Do not use authoring discs. Only general use discs can be written to by a computer drive. ■ You can use DVD-RAM discs that can be removed from a cartridge and DVDRAM discs designed without a cartridge. You cannot use a disc with a 2.6 GB single-sided capacity or 5.2 GB double-sided capacity. ■ Other DVD-ROM drives for computers or other DVD players may not be able to read DVD-R/-RW discs.
Operating Basics ■ Operate the computer in the full-power mode. Do not use powersaving features. ■ Do not write while virus check software is running. Wait for it to finish, then disable virus detection programs including any software that checks files automatically in the background. ■ Do not use hard disk utilities, including those intended to enhance HDD access speed. They may cause unstable operation and data damage. ■ Write from the computer’s HDD to the CD/DVD.
Operating Basics ■ You cannot use Drag’n Drop CD’s music CD function to record music to a DVD-R/-RW disc. ■ Do not use the DISC Backup function of Drag’n Drop CD to copy DVD-Video and DVD-ROM with copyright protection, because the copy will not play correctly. ■ DVD-RAM disc cannot be backed up with the DISC Backup function of Drag’n Drop CD. ■ You cannot backup a CD-ROM or CD-R/-RW to DVD-R/-RW using the DISC Backup function of Drag’n Drop CD.
Operating Basics ■ Do not change the resolution or the number of screen colors while MotionDV STUDIO, DVDfunSTUDIO or DVD-MovieAlbum is running. ■ Although the online manual and Help files indicate that JPEG files can be used, in fact, they cannot be used. ■ 8 cm (3.15") DVD-R/-RW discs cannot be use with DVDfunSTUDIO. ■ DVDfunSTUDIO cannot make DVD-Audio, VideoCD, and miniDVD. ■ DVD-R/-RW discs cannot be written in VR format.
Operating Basics 6. If your CD/DVDs become dusty or dirty, wipe them with a clean dry cloth. Wipe from the centre out, do not wipe in a circular direction around the CD/DVD. If necessary, use a cloth dampened in water or a neutral cleaner. Do not use benzine, thinner or similar cleaner. Diskettes 1. Store your diskettes in the container they came in to protect them and keep them clean. If a diskette is dirty, do not use cleaning fluid. Clean it with a soft damp cloth. 2.
Operating Basics The internal modem does not support voice functions. All data and fax functions are supported. 1. In case of a lightning storm, unplug the modem cable from the telephone jack. 2. Do not connect the modem to a digital telephone line. A digital line will damage the modem. Region selection Telecommunication regulations vary from one region to another, so you will need to make sure the internal modem’s settings are correct for the region in which it will be used.
Operating Basics Open the Dialing Properties dialog box after selecting region. The dialing properties dialog box will be displayed automatically after you select the region. Location list for region selection. A submenu appears displaying location information for telephony. Open dialog box, if the modem and Telephony Current Location region code do not match. A warning dialog box is displayed if current settings for region code and telephony location are incorrect.
Operating Basics If you use a storage device such as an optical drive or HDD connected to a 16-bit PC card, you might experience the following modem problems: 1. Modem speed is slow or communication is interrupted. 2. Skips may occur in sound. Disconnecting To disconnect the internal modem cable, follow the steps below. 1. Pinch the lever on the connector in the telephone jack and pull out the connector. 2. Disconnect the cable from the computer in the same manner.
Operating Basics Security 1. Be sure to enable WEP (encryption) function. Otherwise your computer will allow the illegal access by outsider through wireless LAN to cause illegal intrusion, eavesdropping, and loss or destruction of stored data. TOSHIBA strongly recommend the customer to enable the WEP function. 2. TOSHIBA is not liable for the eavesdropping of data due to the use of wireless LAN and the damage thereof.
Operating Basics Indicator status Indicator off Indicator glows Indication Wireless communication switch is set to off. Automatic power down because of overheating. Power malfunction Wireless communication switch is on. Wireless LAN or Bluetooth is turned on by an application. If you used the Task Bar to disable W-LAN, restart the computer or follow the procedures below to enable the system to recognize W-LAN.
Operating Basics Connecting the LAN cable 3. Plug the other end of the cable into a LAN hub connector. Check with your LAN administrator before connecting to a hub. Disconnecting LAN cable To disconnect the LAN cable, follow the steps below. Make sure the LAN Active indicator (orange LED) is out before you disconnect the computer from the LAN. 1. Pinch the lever on the connector in the computer’s LAN jack and pull out the connector. 2. Disconnect the cable from the LAN hub in the same manner.
Operating Basics Moving the computer The computer is designed for rugged durability. However, a few simple precautions taken when moving the computer will help ensure troublefree operation. ■ Make sure all disk activity has ended before moving the computer. Check the Disk and Slim Select Bay indicators on the computer. ■ If a CD/DVD is in the drives, remove it. Also make sure the drawer is securely closed. ■ Turn off the power to the computer.
Tecra M1 5. Chapter 5 The Keyboard The computer’s keyboard layouts are compatible with a 101/102-key enhanced keyboard. By pressing some keys in combination, all the 101/102-key keyboard functions can be executed on the computer. The number of keys on your keyboard depends on which country/region’s keyboard layout your computer is configured with. Keyboards for numerous languages are available. There are five types of keys: typewriter keys, keypad overlay, function keys, soft keys and cursor control keys.
The Keyboard F1 … F12 function keys The function keys (not to be confused with Fn) are the 12 keys at the top of your keyboard. These keys function differently from other keys. F1 through F12 are called function keys because they execute programmed functions when pressed. Used in combination with the Fn key, keys marked with icons execute specific functions on the computer. See the section, Soft keys: Fn key combinations, in this chapter.
The Keyboard Press Fn + F10 or Fn + F11 to access the integrated keypad. When activated, the keys with gray markings on the bottom edge become numeric keypad keys (Fn + F11) or cursor control keys (Fn + F10). Refer to the Keypad overlay section in this chapter for more information on how to operate these keys. The power on default for both settings is off. Press Fn + F12 (ScrLock) to lock the cursor on a specific line. The power on default is off.
The Keyboard Power save mode: Pressing Fn + F2 changes the power save mode. If you press Fn + F2 in a Windows environment, the Power Save Mode is displayed in a dialog box similar to the one below. Continue holding down Fn and press F2 again to change the setting. You can also change this setting through the Plugged in or Running on batteries item of the Power Saver Properties window in TOSHIBA Power Saver. Standby: When you press Fn + F3, the computer enters Standby.
The Keyboard LCD Display Brightness: Pressing Fn + F7 increases the display brightness in increments. When you press these hot keys, the current setting will be displayed for two seconds by a pop-up icon. You can also change this setting through the Monitor brightness item of the Power Save Mode window in Power Saver. 1. The brightness level is always set at the maximum value for about 18 seconds, when the LCD turns on.
The Keyboard Display resolution selection: Press Fn + space keys to change the display resolution. Each time when you press these hot keys, the display resolution changes as follows: From the current resolution (the original resolution) to 1024X768, from 1024X768 to 800X600, from 800X600 to the original resolution. Fn Sticky key You can use the TOSHIBA Accessibility Utility to make the Fn key sticky, that is, you can press it once, release it, and then press an “F number” key.
The Keyboard Arrow mode To turn on the Arrow mode, press Fn + F10. The Arrow mode F10 indicator lights. Now try cursor and page control using the keys shown in figure below. Press Fn + F10 again to turn off the overlay. Numeric mode To turn on the Numeric mode, press Fn + F11. The Numeric mode F11 indicator lights. Now try numeric data entry using the keys in figure below. Press Fn + F11 again to turn off the overlay.
The Keyboard 2. Check the keyboard indicators. Pressing Fn turns on the most recently used overlay. If the Numeric mode indicator lights, you can use the overlay for numeric entry. If the Arrow mode indicator lights, you can use the overlay for cursor and page control. 3. Release Fn to return to normal keyboard operation. Temporarily changing modes If the computer is in Numeric mode, you can switch temporarily to Arrow mode by pressing a shift key.
Tecra M1 6. Chapter 6 Power and Power-Up Modes The computer’s power resources include the AC adaptor and internal batteries. This chapter gives details on making the most effective use of these resources including charging and changing batteries, tips for saving battery power, and power up modes.
Power and Power-Up Modes Table 6-1 Power conditions continued AC adaptor connected AC adaptor not connected AC adaptor not connected Power on Power off (no operation) • Operates • No charge • LED: 2nd battery green DC IN green 2nd battery • Operates partially charged • Charge*2 or no charge • LED: 2nd battery orange DC IN green No 2nd battery • Operates installed • No charge • LED: 2nd battery off DC IN green Main battery • Operates charge is above • LED: Battery off low battery trigger DC IN off poi
Power and Power-Up Modes *3 For the computer to shut down in hibernation mode, the hibernation feature must be enabled in two places in TOSHIBA Power Saver: the Hibernate window and the Battery Alarm item of the Alarm window. If a main battery and a secondary battery are installed, the computer does not shut down until the charge in both batteries is exhausted. *4 When no secondary battery is installed *5 When no main battery is installed When batteries are charged, the main battery is charged first.
Power and Power-Up Modes Green Indicates the AC adaptor is connected and supplying proper power to the computer. Flashing orange Indicates a problem with the power supply. Plug the AC adaptor into another outlet. If it still does not operate properly, see your dealer. No light Under any other conditions, the indicator does not light. Power indicator Check the Power indicator to determine the power status: Green Indicates power is being supplied to the computer and the computer is turned on.
Power and Power-Up Modes 2. Do not remove the battery pack while the computer is in Standby mode. Data is stored in RAM, so if the computer loses power it will be lost. When the computer is powered off in Standby mode, and the AC adaptor is not connected, the main battery pack and optional secondary battery pack supply power to maintain data and program in memory. If the battery pack(s) is completely discharged, Standby mode does not function and the computer loses all data in memory.
Power and Power-Up Modes Care and use of the battery pack The battery pack is a vital component of portable computing. Taking proper care of it will help ensure longer operating time on battery power as well as a longer life for your battery pack. Follow the instructions in this section carefully to ensure safe operation and maximum performance. Safety precautions Mishandling of batteries can cause death, serious injury or property damage.
Power and Power-Up Modes 8. Never expose the battery pack to abnormal shock, vibration or pressure. The battery pack’s internal protective device will fail, causing it to overheat, explode, ignite or leak caustic liquids possibly resulting in death or serious injury. 9. Never let a battery pack become wet. A wet battery pack will overheat, ignite or rupture possibly resulting in death or serious injury. Warning 1.
Power and Power-Up Modes 6. Be sure to monitor the remaining battery power. If the battery pack and real time clock battery discharge completely, Standby and Suspend will not function and data in memory will be lost. Also, the computer might register an incorrect time and date. In this case, connect the AC adaptor to recharge the batteries. 7. Never install or remove the battery pack without first turning off the power and disconnecting the AC adaptor.
Power and Power-Up Modes Time The following table shows the approximate time required to fully charge a discharged battery. Charging time (hours) Battery type Power on Power off Main battery pack (6600 mAH) 16 about 3 Main battery pack (4400 mAH) 11 about 2.5 Secondary battery pack 9 about 2.5 RTC battery 8 Doesn’t charge The charging time when the computer is on is affected by ambient temperature, the temperature of the computer and how you use the computer.
Power and Power-Up Modes Monitoring battery capacity Remaining battery power can be monitored in the Power Save Modes window in Power Saver. 1. Wait at least 16 seconds after turning on the computer before trying to monitor the remaining operating time. The computer needs this time to check the battery’s remaining capacity and to calculate the remaining operating time, based on the current power consumption rate and remaining battery capacity.
Power and Power-Up Modes Retaining data with power off When you turn off your computer with fully charged batteries, the batteries retain data for the following approximate time periods: Battery pack (6600 mAH) about 12 days (Standby mode) about 43 days (Boot mode) Battery pack (4400 mAH) about 8 days (Standby mode) about 29 days (Boot mode) RTC battery 30 days Extending battery life To maximize the life of your battery pack: ■ At least once a month, disconnect the computer from a power source and op
Power and Power-Up Modes Replacing the battery pack When the battery pack reaches the end of its operating life you will need to install a new one. The life of the battery pack is generally about 500 recharges. If the Battery indicator or Slim Select Bay indicator (if a Slim Select Bay 2nd battery pack is installed) flashes orange shortly after fully recharging the battery, the battery pack needs to be replaced.
Power and Power-Up Modes For environmental reasons, do not throw away a spent battery pack. Please return spent battery packs to your TOSHIBA dealer. Installing the battery pack To install a battery, follow the steps below. The battery pack is a lithium ion battery, which can explode if not properly replaced, used, handled or disposed of. Dispose of the battery as required by local ordinances or regulations. Use only batteries recommended by TOSHIBA as replacements. 1. 2. 3. 4.
Power and Power-Up Modes If you enter the password incorrectly three times in a row, the computer shuts off. In this case, you must turn the computer back on to retry password entry. TOSHIBA Password Utility The TOSHIBA Password Utility provides two levels of password security: User and Supervisor. Passwords set in TOSHIBA Password Utility are different from the Windows password.
Power and Power-Up Modes User Token field ■ Create (button) You can use an SD card token, instead of entering the password. After you have registered a password, insert an SD card and click Create. You can use an SD card of any capacity, but it must be formatted correctly. If an unformatted card or one with an incompatible format is inserted, you will be prompted to format it with a tool named TOSHIBA SD Memory Card Format.
Power and Power-Up Modes 2. Enter the Password. 3. Press Enter. If you enter the password incorrectly three times in a row, the computer shuts off. In this case, you must turn the computer back on to retry password entry. Power-up modes The computer has the following power-up modes: ■ Boot: Computer shuts down without saving data. Always save your work before you turn the computer off in boot mode. ■ Hibernation: Data in memory is saved to the hard disk.
Power and Power-Up Modes System Auto Off This feature turns the system off automatically if it is not used for a set duration. The system shuts down in Standby mode or Hibernation mode in Windows. Tecra M1 6-17 ENGLISH using TecraM1online.dot –– Printed on 24.02.
Tecra M1 7. Chapter 7 HW Setup This chapter explains how to use TOSHIBA HW Setup program to configure your computer. HW Setup TOSHIBA HW Setup lets you configure settings for General, CPU, Boot Priority, Keyboard, LAN, Device Config, Parallel/Printer and Display. If the supervisor password is set, access to the TOSHIBA HW Setup program can be prevented when the user password is used to log on to the computer.
HW Setup There are also three buttons: OK, Cancel and Apply. OK Accepts your changes and closes the HW Setup window. Cancel Closes the window without accepting your changes. Apply Accepts all your changes without closing the HW Setup window. General This window displays the BIOS version and contains two buttons: Default and About. Setup This field displays BIOS Version and date. Default Click Default to return all HW Setup values to the factory settings.
HW Setup Boot Priority Boot Priority Options This option sets the priority for booting the computer. Select from the following settings: HDD −> FDD −> CD-ROM −> LAN The computer looks for bootable files in the following order: HDD, diskette drive, CD-ROM* and LAN. (Default) FDD −> HDD −> CD-ROM −> LAN The computer looks for bootable files in the following order: diskette drive, HDD, CD-ROM* and LAN.
HW Setup 1. If a supervisor password is set, the menu above does not appear when you use the user password to start the computer. 2. The selection method above does not change the boot priority settings in HW Setup. 3. If you press a key other than one of those above or if the selected device is not installed, the system will boot according to the current setting in HW Setup. 4. Support of PCA (ATA) card boot is guaranteed only for TOSHIBA PC card HDDs. 5.
HW Setup Keyboard External Keyboard Fn key Use this option to set a key combination on an external keyboard to emulate the Fn key on the computer’s internal keyboard. Setting an Fn key equivalent will let you use Hotkeys by pressing the set combination instead of the Fn key (PS/2 keyboard only).
HW Setup Built-in LAN This feature enables or disables the Built-in LAN. Enabled Enables Built-in LAN functions. (Default) Disabled Disables Built-in LAN functions. Device Config Device Configuration This option lets you set the device configuration. Setup by OS Operating system sets devices that it can control. (Default) All Devices BIOS sets all devices. Parallel/Printer This tab lets you set the Printer Port Type. Use the Windows Device Manager to make settings for the Parallel port.
HW Setup USB USB KB/Mouse Legacy Emulation Use this option to enable or disable USB KB/Mouse Legacy Emulation. If your operating system does not support USB, you can still use a USB mouse and keyboard by setting the USB KB/Mouse Legacy Emulation item to Enabled. Enabled Enables the USB KB/Mouse Legacy Emulation. (Default) Disabled Disables the USB KB/Mouse Legacy Emulation. USB-FDD Legacy Emulation Use this option to enable or disable USB-FDD Legacy Emulation.
Tecra M1 8. Chapter 8 Optional Devices Optional devices can expand the computer’s capabilities and its versatility. This chapter describes connection or installation of the following devices, which are available from your TOSHIBA dealer: Cards/memory ■ PC cards ■ SD cards ■ Memory expansion Power devices ■ ■ ■ ■ Additional battery pack Slim Select Bay 2nd battery pack Additional AC adaptor Battery charger Peripheral devices ■ ■ ■ ■ Slim Select Bay HDD adaptor External monitor TV i.
Optional Devices PC cards The computer is equipped with a PC card expansion slot that can accommodate one 5 mm Type II card. Any PC card that meets industry standards (manufactured by TOSHIBA or other vendor) can be installed. The slot supports 16-bit PC cards, including PC card 16’s multifunction card and CardBus PC cards. CardBus supports the new standard of 32-bit PC cards. The bus provides superior performance for the greater demands of multimedia data transmission.
Optional Devices Removing a PC card To remove the PC card, follow the steps below. 1. Slide the PC card lock into the unlocked position. 2. In Windows XP, open the Safety Remove Hardware icon on the system tray and disable the PC card. 3. Press the PC card eject button to extend it. 4. Press the extended eject button to pop the card out slightly. 5. Pinch the PC card and remove it.
Optional Devices SCREW PC CARD LOCK Securing the PC card lock in the lock position Unlocking the PC card slot To unlock the PC card slot, follow the steps below. 1. Remove the screw securing the PC card lock. 2. Slide the PC card lock to the unlocked position. The metal tongue covering the PC card slot will be retracted. 3. Secure the PC card lock with the screw. SCREW PC CARD LOCK Securing the PC card lock in the unlock position Tecra M1 8-4 ENGLISH using TecraM1online.dot –– Printed on 24.02.
Optional Devices SD cards The computer is equipped with an SD card slot that can accommodate Secure Digital flash memory cards with various memory capacities. SD cards let you easily transfer data from devices, such as digital cameras and Personal Digital Assistants, that use SD card flash-memory. The cards have a high level of security and copy protection features. The slot cannot accommodate Multi Media cards. Keep foreign objects out of the SD card slot.
Optional Devices SD CARD Inserting an SD card Make sure the SD card is oriented properly before you insert it. Removing an SD card To remove an SD card, follow the steps below. 1. Click the Safety Remove Hardware icon on the Task Bar. 2. Point to SD card and click. 3. Push in the card and release it to pop the card out slightly. 4. Pinch the card and remove it. SD CARD INDICATOR SD CARD Removing an SD card Tecra M1 8-6 ENGLISH using TecraM1online.dot –– Printed on 24.02.
Optional Devices Make sure the SD card indicator is out before you remove the card or turn off the computer’s power. If you remove the card or turn off the power while the computer is accessing the card you may lose data or damage the card. Please do not remove the SD card from the SD card slot while in Standby or in Hibernation state. If you do, PC may become unstable or the data in SD card may be lost. SD card care Set the write-protect switch to the lock position, if you do not want to record data. 1.
Optional Devices Memory expansion This computer is equipped with two memory module sockets beneath the keyboard. You can increase the amount of RAM by installing an additional memory or replacing default memories with additional memories. This section describes how to install and remove a memory module. Place a mat beneath the computer to prevent making a scratch on the lid when replacing the memory module. Avoid the mat that generates static electricity. Use only memory modules approved by TOSHIBA.
Optional Devices KEYBORD BRACE Removing the keyboard brace 6. Remove three screws (right and left at the both right and left end and in the upper middle of the keyboard) fixing the keyboard. Removing the keyboard (1) Be careful not to drop the screw inside the computer when removing. 7. Press the keyboard to the other side. Turn the keyboard upside down when a flat cable appears. Do not pull the keyboard when turning over.
Optional Devices SLITS TABS Removing the keyboard (2) Removing the keyboard (3) 8. Raise the insulation sheet covering the memory module to appear the module. Tecra M1 8-10 ENGLISH using TecraM1online.dot –– Printed on 24.02.
Optional Devices Raising the insulation sheet 9. Keep the insulation sheet raised using adhesive tape. Raising the insulation sheet 10. Insert a new module to the socket and push it downward to lie flat. Latches on either side will click into place to secure the module. Tecra M1 8-11 ENGLISH using TecraM1online.dot –– Printed on 24.02.
Optional Devices Installing a memory module Installing two memory modules Tecra M1 8-12 ENGLISH using TecraM1online.dot –– Printed on 24.02.
Optional Devices 11. Seat the insulation sheet to cover the module. Be sure to check that the insulation sheet is returned to the original position to cover the memory module. 12. Insert two tabs of the keyboard into the slits of the computer case and seat the keyboard at the original position. Fix it with three screws removed in 6. Be sure to use all screws that were removed in 6 and do not leave foreign matters such as adhesive tape used in 9 or screws removed and dropped in the computer. 13.
Optional Devices Removing the memory module 6. Follow the instructions 11 through 15 in “Installing memory module”. Hard disk drive pack An extra HDD expands the flexibility of your system and lets you carry your data without carrying the computer. Use a point size 0 Phillips screwdriver. Removing the HDD pack To remove the HDD pack, follow the steps below and refer to figures below. 1. Set the computer to boot mode and turn off the power. 2.
Optional Devices Removing the HDD pack cover 7. Raise the HDD plastic tab, pinch it and slide the HDD pack to disconnect from the connector. Be sure to slide the HDD pack first and confirm that the HDD pack has disconnected. 8. Lift the HDD pack and remove it. Removing the HDD pack Installing the HDD pack To install the hard disk drive, follow the steps below. 1. Place the HDD into the space for HDD. Slide the HDD to connect to the connector. 2.
Optional Devices Installing the HDD pack 3. Seat the cover and press down until the latches click into place. 4. Secure the cover with a screw. Additional battery pack You can increase the portability of the computer with additional battery packs. If you’re away from an AC power source and your battery runs low, you can replace it with a freshly charged battery. See Chapter 6, Power and Power-Up Modes.
Optional Devices Inserting the secondary battery pack in the adaptor Removing To remove the secondary battery from the adaptor, follow the steps below. 1. Slide the latch in the direction of the arrow shown below. 2. Push the secondary battery pack up from the bottom and lift it out.
Optional Devices Slim Select Bay HDD adaptor A integrated 2 1/2" HDD is available for insertion in the Slim Select Bay. To install an HDD in the Slim Select Bay HDD adaptor follow the steps below. 1. Slide the lock to the unlock position and open the lid. Opening the lid 2. Insert the HDD and push forward to ensure a firm connection. Inserting the HDD 3. Close the lid and slide the lock to the lock position. Tecra M1 8-18 ENGLISH using TecraM1online.dot –– Printed on 24.02.
Optional Devices Closing the lid For details on inserting the Slim Select Bay HDD adaptor in the Slim Select Bay, refer to Chapter 4, Operating Basics. External monitor An external analog monitor can be connected to the external monitor port on the computer. The computer supports VGA and Super VGA video modes. To connect a monitor, follow the steps below. 1. Turn the computer off. 2. Connect the monitor to the external monitor port. 3. Turn the monitor’s power on. 4. Turn the computer on.
Optional Devices If a television is connected to the computer, set the TV type in Display Properties. Follow the steps below. a. Click start and click Control Panel. b. Double-click the Display icon to open the Display Properties window. c. Click the Settings tab and click the Advanced button. d. Click the Display Device tab. e. Select the TV Standard that your TV supports. Changing the resolution If you want to change the resolution, follow the steps below. 1.
Optional Devices ■ If you connect/disconnect an iLINK device to/from another iLINK device that is currently exchanging data with the computer, data frames might be dropped. ■ Make sure data transfer has ended or turn off the computer, before you: ■ Connect/disconnect an iLINK device to/from the computer. ■ Connect/disconnect an iLINK device to/from another iLINK device that is connected to the computer. Connecting 1. Make sure the connectors are properly aligned and plug the i.
Optional Devices You must connect the AC adaptor before you connect to a Port Replicator. The following ports and accessories are available on the Port Replicator.
Optional Devices Security lock Security locks enable you to anchor your computer and optional Advanced Port Replicator II to a desk or other heavy object to help prevent unauthorized removal of the computer or Advanced Port Replicator. The computer has a security lock slot on the right side. Attach one end of a cable to a desk and the other end to the security lock slot. 1. Turn the computer so the right side faces you. 2. Align the holes for the security lock and attach the lock.
Tecra M1 9. Chapter 9 Troubleshooting TOSHIBA designed the computer for durability. However, should problems occur, following the procedures in this chapter can help to determine the cause. All readers should become familiar with this chapter. Knowing what might go wrong can help prevent problems from occurring. Problem solving process Resolving problems will be much easier if you observe the following guidelines: ■ Stop immediately when you recognize a problem exists.
Troubleshooting ■ Inspect all connecting cables for loose wires and all connectors for loose pins. ■ Check that your diskette or CD/DVD-ROM is correctly inserted and that the diskette’s write protect tab is correctly set. Make notes of your observations and keep them in a permanent error log. This will help you describe your problems to your dealer. If a problem recurs, the log will help you identify the problem faster.
Troubleshooting Hardware If you cannot find a software problem, check your hardware. First run through the items in the preliminary checklist above. If you still cannot correct the problem, try to identify the source. The next section provides checklists for individual components and peripherals. Hardware and system checklist This section discusses problems caused by your computer’s hardware or attached peripherals.
Troubleshooting If any of the following conditions are present, the self test failed: ■ The computer stops and does not proceed to display information or messages except the TOSHIBA logo. ■ Random characters appear on the screen, and the system does not function normally. ■ The screen displays an error message. Turn off the computer and check all cable connections as well as PC card and memory module connections. If the test fails again, contact your dealer.
Troubleshooting Problem Procedure AC adaptor doesn’t Check the connections. Make sure the cord is power the computer firmly connected to the computer and a power (DC IN indicator does outlet. not glow green) Check the condition of the cord and terminals. If the cord is frayed or damaged, replace it. If the terminals are soiled, wipe them with cotton or a clean cloth. If the AC adaptor still does not power the computer, contact your dealer.
Troubleshooting Battery doesn’t power the computer as long as expected Check the power consumption settings in TOSHIBA Power Saver Utility. Consider using a power saving mode. Password Problem Procedure Cannot enter or forgot password Contact your dealer. For information on setting a password, refer to Chapter 6, Power and Power-Up Modes, starting the computer by Password, TOSHIBA Password Utility.
Troubleshooting Markings appear on the LCD. They might have come from contact with the keyboard or Dual Pointing Device. Try wiping the LCD gently with a clean dry cloth. If markings remain, use LCD cleaner. Be sure to let the LCD dry before closing it. Problems above Refer to your software’s documentation to remain unresolved or determine if the software is causing the difficulty. other problems occur Contact your dealer if the problems continue.
Troubleshooting CD-ROM drive For more information, refer to Chapter 4, Operating Basics. Problem Procedure You cannot access a CD in the drive Make sure the drive’s drawer is securely closed. Press gently until it clicks into place. Open the drawer and make sure the CD is properly seated. It should lie flat with the label facing up. A foreign object in the drawer could block laser light from reading the CD. Make sure there is no obstruction. Remove any foreign object. Check whether the CD is dirty.
Troubleshooting A foreign object in the drawer could block laser light from reading the CD/DVD. Make sure there is no obstruction. Remove any foreign object. Check whether the CD/DVD is dirty. If it is, wipe it with a clean cloth dipped in water or a neutral cleaner. See the Media care section in Chapter 4 for details on cleaning. Some CD/DVDs run correctly, but others do not The software or hardware configuration may be causing a problem.
Troubleshooting Check whether the CD/DVD is dirty. If it is, wipe it with a clean cloth dipped in water or a neutral cleaner. See the Media care section in Chapter 4 for details on cleaning. Some CD/DVDs run correctly, but others do not The software or hardware configuration may be causing a problem. Make sure the hardware configuration matches your software’s needs. Check the CD/DVD’s documentation. Check the type of CD/DVD you are using.
Troubleshooting Problem Procedure You cannot access a CD/DVD in the drive Make sure the drive’s drawer is securely closed. Press gently until it clicks into place. Open the drawer and make sure the CD/DVD is properly seated. It should lie flat with the label facing up. A foreign object in the drawer could block laser light from reading the CD/DVD. Make sure there is no obstruction. Remove any foreign object. Check whether the CD/DVD is dirty.
Troubleshooting Cannot write correctly If you have trouble writing, make sure you are observing the following precautions: ■ Use only media recommended by TOSHIBA. ■ Do not use the mouse or keyboard during writing. ■ Use only the software supplied with the computer for recording. ■ Do not run or start other software during writing. ■ Do not jar the computer during writing. ■ Do not connect/ disconnect external devices or install/remove internal cards during writing.
Troubleshooting PC card Refer also to Chapter 8, Optional Devices. Problem Procedure PC card error occurs Reseat the PC card to make sure it is firmly connected. Make sure the connection between the external device and the card is firm. Check the card’s documentation. If problems persist, contact your dealer. Infrared port Refer also to the documentation for your IrDA compatible device and related software.
Troubleshooting The mouse pointer Try changing the speed setting in the mouse moves too fast or too control utility. slow 1. Open the Control Panel, select the Mouse icon and press Enter. 2. Click the Pointer Options tab. 3. Set the speed as instructed and click OK. Double-tapping (Touch Pad) or double-clicking (AccuPoint) does not work Try changing the double-click speed setting in the mouse control utility. 1. Open the Control Panel, select the Mouse icon and press Enter. 2. Click the Buttons tab. 3.
Troubleshooting USB Refer also to your USB device’s documentation. Problem Procedure USB device does not Check for a firm cable connection between the work USB ports on the computer and the USB device. Make sure the USB device drivers are properly installed. Refer to your Windows XP documentation for information on checking the drivers. If problems persist, contact your dealer. Memory expansion Refer also to Chapter 8, Optional Devices, for information on installing memory modules.
Troubleshooting Problem Procedure Beep sounds. (Two beeps, a dash and a dot, for a defective memory module in slot A. Three beeps, a dash and two dots for slot B. When both beeps sound, both memories in slot A and B are defective.) Make sure the memory module installed in the expansion slot is compatible with the computer. If an incompatible module has been installed, follow the steps below. 1. Disconnect the AC adaptor and all peripheral devices 2. Remove the battery. 3. Remove the memory module. 4.
Troubleshooting Reinstall the drivers. Open the Windows Control Panel and double-click the Add Hardware icon. Follow the on-screen directions. Restart Windows. If problems persist, contact your dealer. Modem Refer to the online help files for Appendix C and D. Problem Procedure Communication software can’t initialize modem Make sure the computer’s internal modem settings are correct. Refer to Phone and Modem Properties in the Control Panel.
Troubleshooting You cannot receive an incoming call Check the rings before auto answer setting in your communications application. You can also use the ATS0 command. Refer to the online help files for Appendix D, S-registers. If problems persist, contact your dealer. LAN Problem Procedure Cannot access LAN Check for a firm cable connection between the LAN jack and the LAN HUB. Wake-up on LAN does not work Make sure the AC adaptor is connected.
Troubleshooting Bluetooth function and an optional Bluetooth PC card cannot operate simutaneously. If problems persist, contact your dealer. Real Time Clock Problem Procedure The following message is Displayed on the LCD: RTC battery is low or CMOS checksum is inconsistentPress [F1] key to set Date/Time. The battery for RTC is wearing. Set the date and time in BIOS setup with the following steps: 1. Press [F1] key. BIOS setup will boot up. 2. Set the date in [System Date]. 3.
Tecra M1 A. Appendix A Specifications This appendix summarizes the computer’s technical specifications. Physical Dimensions Weight (typical) 2.6 kilograms, configured with: 14" XGA, 256 MB RAM, 30GB HDD, DVD-ROM drive, modem, LAN, 6-cell battery 2.8 kilograms, configured with: 14" SXGA+, 256 MB RAM, 30 GB HDD, CD-RW/DVD drive, modem, LAN, 9-cell battery Weight will vary with other configurations. Above weights are measured at a specific criteria.
Specifications Conditions Altitude (from sea level) Operating -60 to 3,000 meters Non-operating -60 to 10,000 meters maximum Power Requirements AC adaptor 100-240 volts AC 50 or 60 hertz (cycles per second) Computer 15 VDC 5.
Specifications Communication speed Data transmission and reception 300/1200/2400/4800/7200/9600/12000/ 14400/16800/19200/21600/24000/26400/ 28800/31200/33600 bps Data reception only with V.
Tecra M1 B. Appendix B AC Power Cord and Connectors The power cord’s AC input plug must be compatible with the various international AC power outlets and the cord must meet the standards for the country/region in which it is used. All cords must meet the following specifications: Length: Minimum 2 meters Wire size: Minimum 0.75 mm2 Current rating: Minimum 2.5 amperes Voltage rating: 125 or 250 VAC (depending on country/region’s power standards) Certification agencies U.S.
AC Power Cord and Connectors For the United States and Canada, plug configuration must be a 2-15P (250 V) or 1-15P (125 V) as designated in the U.S. National Electrical code handbook and the Canadian Electrical Code Part II. The following illustrations show the plug shapes for the U.S.A. and Canada, the United Kingdom, Australia and Europe.
Tecra M1 C. Appendix C The TOSHIBA International Warranty The TOSHIBA International Warranty is a service policy on the parts and repair on your TOSHIBA portable personal computer which is automatically available to purchasers of the computer. The cover is assured in major industrial countries of the world. It means that wherever you take your TOSHIBA mobile PC in this area, you will never be left without help should any problems arise.
The TOSHIBA International Warranty TOSHIBA’s Worldwide Computer Representatives Australia Toshiba (Australia) Pty. Limited 84-92 Talavera Road, North Ryde NSW 2113 Tel: +61-2-9887-3322 Fax: +61-2-9888-3664 http://www.isd.toshiba.com.au Austria Toshiba Europe GmbH Handelskai 388 1020 Wien Tel: +43-1-72031000 Fax: +43-1-72031002 http://www.toshiba.at Azerbaijan AZEL (Azerbaijan Electronics) Floor 5, 65 Fizuli Str. 370014 Baku Tel: +99412-974040 Fax: +99412-974042 http://www.azel.
The TOSHIBA International Warranty Hungary Technotrade Kft. Öv u, 185, 1147 Budapest Ireland See 'United Kingdom' Israel Mafil Technologies (3000) Ltd 8 Bareket Street 49517 Petah Tikwa Tel: +972-3-918-3333 Fax: +972-3-924-1310 http://www.mafil.co.il Italy Progetto Elettronica 92 .S.p.A Via de Gasperi 88a, 20017 Mazzo di Rho Tel: +39-02-9397-5551 Fax: +39-02-9397-5299 http://www.pe92.
The TOSHIBA International Warranty Oman (Sultanate of Oman) Suhail&Saud Bahwan (SSB) Sarco Building, Ground Floor No. 459, Way No. 310 Al Noor Street, Ruwi 113 Muscat Tel: +968-790 117 Fax: +968-790 192 http://www.ssbcd.co.com Poland AC Serwis Sp. Z o. o. ul. Partyzantów 71, 43-316 Bielsko-Biala Tel: +48- 33-8130-205 Fax: +48- (33-8130-209 http://www.acserwis.com.pl Portugal Toshiba Information Systems Portugal Edificio D.
The TOSHIBA International Warranty Turkey Bekom Bilgisayar Elekronik Komunikasyon Buyukdere Cad. Laie Ishani No. 62 K., 1 Mecidiyeköy, Istanbul Tel: +90 212 275 87 97 Fax: +90 212 275 8740 http://www.toshibatr.com Ukraine DKT-SERSO Lesya Ukrainka blv, 26 01133 Kiev Tel: +380-44-573-9627 Fax: +380-44-254-4646 http://www.dkt-cepco.com.ua United Arab Emirates Al-Futtaim Electronics P.O.
Tecra M1 D.
Keyboard Layouts French German Italian Tecra M1 D-2 ENGLISH using TecraM1online.dot –– Printed on 24.02.
Keyboard Layouts Norwegian Polish Portuguese Tecra M1 D-3 ENGLISH using TecraM1online.dot –– Printed on 24.02.
Keyboard Layouts Spanish Swedish Swiss-German Tecra M1 D-4 ENGLISH using TecraM1online.dot –– Printed on 24.02.
Keyboard Layouts UK English US English Tecra M1 D-5 ENGLISH using TecraM1online.dot –– Printed on 24.02.
Tecra M1 E. Appendix E Display Controller and Modes Display controller The display controller interprets software commands into hardware commands that turn particular pels on or off. The controller is an advanced Video Graphics Array (VGA) that provides Super VGA (SVGA) and Extended Graphics Array (XGA), Super Extended Graphics Array (SXGA), Super Extended Graphics Array plus (SXGA+), support for the internal LCD and external monitors. Two models are available: ■ 14.
Display Controller and Modes Video modes The computer supports video modes defined in the tables below. If your application offers a selection of mode numbers that do not match the numbers on the table, select a mode based on mode type, resolution, character matrix, number of colors and refresh rates. Also, if your software supports both graphics and text modes, the screen display may appear to operate faster using a text mode.
Display Controller and Modes Table1 Video modes (VGA) continued Video mode Type Resolution Character matrix (pels) LCD colors CRT colors Scanning frequency Vertical (Hz) D VGA Grph 320 x 200 Pels 8x8 16 of 256K 16 of 256K 70 E VGA Grph 640 x 200 Pels 8x8 16 of 256K 16 of 256K 70 F VGA Grph 640 x 350 Pels 8 x 14 Mono 70 10 VGA Grph 640 x 350 Pels 8 x 14 16 of 256K 16 of 256K 70 11 VGA Grph 640 x 480 Pels 8 x 16 2 of 256K 60 12 VGA Grph 640 x 480 Pels 8 x 16 16 of 256K
Display Controller and Modes Table 2 Video modes (XGA) Resolution LCD colors CRT colors Vertical frequency (Hz) 640 x 480 256/256K 256/256K 60 75 85 100 800 x 600 256/256K 256/256K 60 75 85 100 1024 x 768 256/256K 256/256K 60 75 85 100 1280 x 1024 256/256K (Virtual) 256/256K 60 75 85 100 1600 x 1200 256/256K (Virtual) 256/256K 60 75 85 1920 x 1440 256/256K (Virtual) 256/256K 60 2048 x 1536 256/256K (Virtual) 256/256K 60 Tecra M1 E-4 ENGLISH using TecraM1online.
Display Controller and Modes Table 2 Video modes (XGA) continued Resolution LCD colors CRT colors Vertical frequency (Hz) 640 x 480 64K/64K 64K/64K 60 75 85 100 800 x 600 64K/64K 64K/64K 60 75 85 100 1024 x 768 64K/64K 64K/64K 60 75 85 100 1280 x 1024 64K/64K (Virtual) 64K/64K 60 75 85 100 1600 x 1200 64K/64K (Virtual) 64K/64K 60 75 85 1920 x 1440 64K/64K (Virtual) 64K/64K 60 2048 x 1536 64K/64K (Virtual) 64K/64K 60 Tecra M1 E-5 ENGLISH using TecraM1online.
Display Controller and Modes Table 2 Video modes (XGA) continued Resolution LCD colors CRT colors Vertical frequency (Hz) 640 x 480 16M/16M 16M/16M 60 75 85 100 800 x 600 16M/16M 16M/16M 60 75 85 100 1024 x 768 16M/16M 16M/16M 60 75 85 100 1280 x 1024 16M/16M (Virtual) 16M/16M 60 75 85 100 1600 x 1200 16M/16M (Virtual) 16M/16M 60 75 85 1920 x 1440 16M/16M (Virtual) 16M/16M 60 2048 x 1536 16M/16M (Virtual) 16M/16M 60 Tecra M1 E-6 ENGLISH using TecraM1online.
Display Controller and Modes Table 3 Video modes (Super XGA+) Resolution LCD colors CRT colors Vertical frequency (Hz) 640 x 480 256/256K 256/256K 60 75 85 100 800 x 600 256/256K 256/256K 60 75 85 100 1024 x 768 256/256K 256/256K 60 75 85 100 1280 x 1024 256/256K 256/256K 60 75 85 100 1400 x 1050 256/256K 256/256K 60 1600 x 1200 256/256K (Virtual) 256/256K 60 75 85 1920 x 1440 256/256K (Virtual) 256/256K 60 2048 x 1536 256/256K (Virtual) 256/256K 60 Tecra M1 E-7 ENGLISH
Display Controller and Modes Table 3 Video modes (Super XGA+) continued Resolution LCD colors CRT colors Vertical frequency (Hz) 640 x 480 64K/64K 64K/64K 60 75 85 100 800 x 600 64K/64K 64K/64K 60 75 85 100 1024 x 768 64K/64K 64K/64K 60 75 85 100 1280 x 1024 64K/64K 64K/64K 60 75 85 100 1400 x 1050 64K/64K 64K/64K 60 1600 x 1200 64K/64K (Virtual) 64K/64K 60 75 85 1920 x 1440 64K/64K (Virtual) 64K/64K 60 2048 x 1536 64K/64K (Virtual) 64K/64K 60 Tecra M1 E-8 ENGLISH using
Display Controller and Modes Table 3 Video modes (Super XGA+) continued Resolution LCD colors CRT colors Vertical frequency (Hz) 640 x 480 16M/16M 16M/16M 60 75 85 100 800 x 600 16M/16M 16M/16M 60 75 85 100 1024 x 768 16M/16M 16M/16M 60 75 85 100 1280 x 1024 16M/16M 16M/16M 60 75 85 100 1400 x 1050 16M/16M 16M/16M 60 1600 x 1200 16M/16M (Virtual) 16M/16M 60 75 85 1920 x 1440 16M/16M (Virtual) 16M/16M 60 2048 x 1536 16M/16M 16M/16M 60 Tecra M1 E-9 ENGLISH using TecraM1on
Tecra M1 F. Appendix F If your computer is stolen Always take care of your computer and try to prevent it from being stolen. You are the owner of a valuable technical device, which may be highly attractive to thieves, so please do not leave it unattended in a public place. To further help protect against theft, security cables can be bought for use with your notebook when it is being used at home or in the office.
If your computer is stolen Toshiba Theft Registration Send to: Toshiba Europe GmbH Technical Service and Support Leibnizstr. 2 93055 Regensburg Germany Fax number: +49 (0) 941 7807 925 Country stolen: Machine type: (e.g. Tecra 9100) Model number: (e.g. PA1218E YXT) Serial number: (e.g. 70123456E) Date stolen: Warranty seal: (e.g. 9813 123456 049) Owner’s details Name: Company: Street: Postal Code/City: Country: Phone: Fax: Tecra M1 F-2 ENGLISH using TecraM1online.dot –– Printed on 24.02.
Tecra M1 G. Appendix G ASCII Character Codes This appendix shows the American Standard Code for Information Interchange (ASCII) on the following pages. The characters in the IBM char column appear on your display when you type the corresponding ASCII code (as described in Chapter 5, The Keyboard). The characters that are printed, however, depend on the software you are using. For most software, the printed output for decimal codes 32 to 128 will match your screen display.
ASCII Character Codes Dec code Hex code IBM char Sort seq Dec code Hex code IBM char Sort seq 032 033 034 035 036 037 038 039 040 041 042 043 044 045 046 047 048 049 050 051 052 053 054 055 056 057 058 059 060 061 062 063 20 21 22 23 24 25 26 27 28 29 2A 2B 2C 2D 2E 2F 30 31 32 33 34 35 36 37 38 39 3A 3B 3C 3D 3E 3F space ! “ # $ % & ’ ( ) * + , .
ASCII Character Codes Dec code Hex code IBM char Sort seq Dec code Hex code IBM char Sort seq 096 097 098 099 100 101 102 103 104 105 106 107 108 109 110 111 112 113 114 115 116 117 118 119 120 121 122 123 124 125 126 127 60 61 62 63 64 65 66 67 68 69 6A 6B 6C 6D 6E 6F 70 71 72 73 74 75 76 77 78 79 7A 7B 7C 7D 7E 7F ’ a b c d e f g h i j k l m n o p q r s t u v w x y z { 96 97 98 99 100 101 102 103 104 105 106 107 108 109 110 111 112 113 114 115 116 117 118 119 120 121 122 123 124 125 126 127 1
ASCII Character Codes Dec code Hex code IBM char Sort seq Dec code Hex code 160 161 162 163 164 165 166 167 168 169 170 171 172 173 174 175 176 177 178 179 180 181 182 183 184 185 186 187 188 189 190 191 A0 A1 A2 A3 A4 A5 A6 A7 A8 A9 AA AB AC AD AE AF B0 B1 B2 B3 B4 B5 B6 B7 B8 B9 BA BB BC BD BE BF á í ó ú ñ Ñ a o ¿ 65 73 79 85 78 78 166 167 63 169 170 171 172 33 34 34 192 193 194 195 196 197 198 199 200 201 202 203 204 205 206 207 208 209 210 211 212 213 214 215 216 217 218 219 220 221 222 223
ASCII Character Codes Dec code Hex code IBM char 224 225 226 227 228 229 230 231 232 233 234 235 236 237 238 239 240 241 242 243 244 245 246 247 248 249 250 251 252 253 254 255 E0 E1 E2 E3 E4 E5 E6 E7 E8 E9 EA EB EC ED EE EF F0 F1 F2 F3 F4 F5 F6 F7 F8 F9 FA FB FC FD FE FF α ß Γ Π ∑ σ µ ϒ Φ Θ Ω δ ϕ φ Ε Λ Ξ ± ≥ ≤ ⌠ ⌡ ÷ ≈ Sort seq 83 ° √ η 2 Tecra M1 G-5 ENGLISH using TecraM1online.dot –– Printed on 24.02.
Tecra M H. Appendix H V.90 The TOSHIBA internal modem uses V.90 technology. The modem is capable of downstream speeds of 56Kbps (kilobits per second) when connected to an Internet service provider that supports V.90. As with any modem, the actual throughput (speed of data transfer) depends on analog telephone line conditions, which can vary considerably. Therefore, many users will experience throughput in the range of 28-50Kbps under normal telephone line conditions. Upstream data flows at the V.34 rate.
V.90 Table E-1 Result codes for a V.90 connection No.
V.90 V42bis V.42 error control and V.42bis data compression V42 V.42 error control only NoEC No error control protocol AT Command -V90=* V.90 Dial Line Rate -V90 sets the maximum V.90 downstream that the modem attempts to connect. -V90=0 V.90 disabled -V90=1 V.90 enabled: automatic speed selection maximum modem speed (default) TECRA M1 H-3 ENGLISH using TecraM1online.dot –– Printed on 24.02.
Tecra M1 I. Appendix I Internal Modem Guide This appendix describes how to install and the remove the internal modem. Do not disassemble the computer beyond the steps described in this instruction or touch any components not specifically described. Installing the internal modem The internal modem is preinstalled. The following is for information only. To install the internal modem follow the procedures below. Installing the modem board and jack To install the modem board and jack, follow the steps below.
Internal Modem Guide Removing the internal modem To remove the internal modem, follow the steps below. 1. Save your data and turn off the computer. 2. Disconnect the AC adaptor and any other peripheral device. 3. Turn the computer upside down and remove the battery pack. 4. Remove one screw securing the cover. 5. Remove the modem cover. 6. Remove two screws and remove the modem board. 7. Disconnect the modem cable. 8. Secure the modem cover with one screw. 9. Install the battery pack.
Tecra M1 J. Appendix J Wireless LAN This appendix is intended to help you get your Wireless LAN network up and running, with a minimum of parameters. Card specifications Form Factor ■ Mini PCI TypeIII Capability ■ IEEE 802.
TECRA M1 Version 1 Last Saved on 22.02.2003 09:47 Wireless LAN R-F Frequency ■ Band 5 GHz (5150-5850 MHz) (Revision A, Turbo Mode) ■ Band 2.4 GHz (2400-2483.5 MHz) (Revision B) Modulation Technique Direct Sequence Spread Spectrum ■ CCK, DQPSK, DBPSK (Revision B) ■ OFDM-BPSK, OFDM-QPSK, OFDM16QAM, OFDM-64QAM (Revision A, Turbo Mode) The range of the wireless signal is related to the transmit rate of the wireless communication. Communications at lower transmit range may travel larger distances.
TECRA M1 Version 1 Last Saved on 22.02.2003 09:47 Wireless LAN ■ For wireless clients that operate in a Wireless LAN Infrastructure, the Wireless LAN card will automatically start operation at the channel identified by the Wireless LAN Access Point. When roaming between different access points the station can dynamically switch to another channel if required. ■ For Wireless LAN cards installed in wireless clients operating in a peer-to-peer mode, the card will use the default channel 10.
Tecra M1 1. Glossary The terms in this glossary cover topics related to this manual. Alternate naming is included for reference.
TECRA M1 Version 1 Last Saved on 23.02.
TECRA M1 Version 1 Last Saved on 23.02.2003 13:48 Glossary A AccuPoint: A pointing device integrated into the TOSHIBA computer keyboard. adaptor: A device that provides an interface between two dissimilar electronic devices. For example, the AC adaptor modifies the power from a wall outlet for use by the computer. This term also refers to the add-in circuit cards that control external devices, such as video monitors and magnetic tape devices. allocate: To assign a space or function for a specific task.
TECRA M1 Version 1 Last Saved on 23.02.2003 13:48 Glossary BIOS: Basic Input Output System. The firmware that controls data flow within the computer. See also firmware. bit: Derived from "binary digit," the basic unit of information used by the computer. It is either zero or one. Eight bits is one byte. See also byte. board: A circuit board. An internal card containing electronic components, called chips, which perform a specific function or increase the capabilities of the system.
TECRA M1 Version 1 Last Saved on 23.02.2003 13:48 Glossary chip: A small semiconductor containing computer logic and circuitry for processing, memory, input/output functions and controlling other chips. CMOS: Complementary Metal-Oxide Semiconductor. An electronic circuit fabricated on a silicon wafer that requires very little power. Integrated circuits implemented in CMOS technology can be tightly packaged and are highly reliable.
TECRA M1 Version 1 Last Saved on 23.02.2003 13:48 Glossary D data: Information that is factual, measurable or statistical that a computer can process, store, or retrieve. data bits: A data communications parameter controlling the number of bits (binary digits) used to make up a byte. If data bits = 7 the computer can generate 128 unique characters. If data bits = 8 the computer can generate 256 unique characters. DC: Direct Current. Electric current that flows in one direction.
TECRA M1 Version 1 Last Saved on 23.02.2003 13:48 Glossary DVD-ROM: A Digital Versatile Disc Read Only Memory is a high capacity, high performance disc suitable for play back of video and other high-density files. The DVD-ROM drive uses a laser to read data from the disc. E echo: To send back a reflection of the transmitted data to the sending device. You can display the information on the screen, or output it to the printer, or both.
TECRA M1 Version 1 Last Saved on 23.02.2003 13:48 Glossary G gigabyte (GB): A unit of data storage equal to 1024 megabytes. See also megabyte. graphics: Drawings, pictures, or other images, such as charts or graphs, to present information. H hard disk: A non-removable disk usually referred to as drive C. The factory installs this disk and only a trained engineer can remove it for servicing. Also called fixed disk. hard disk drive (HDD): An electromechanical device that reads and writes a hard disk.
TECRA M1 Version 1 Last Saved on 23.02.2003 13:48 Glossary interface: 1) Hardware and/or software components of a system used specifically to connect one system or device to another. 2) To physically connect one system or device to another to exchange information. 3) The point of contact between user, the computer, and the program, for example, the keyboard or a menu. interrupt request: A signal that gives a component access to the processor. I/O: Input/output.
TECRA M1 Version 1 Last Saved on 23.02.2003 13:48 Glossary M main board: See motherboard. megabyte (MB): A unit of data storage equal to 1024 kilobytes. See also kilobyte. megahertz: A unit of wave frequency that equals 1 million cycles per second. See also hertz. menu: A software interface that displays a list of options on the screen. Also called a screen. microprocessor: A hardware component contained in a single integrated circuit that carries out instructions.
TECRA M1 Version 1 Last Saved on 23.02.2003 13:48 Glossary online state: A functional state of a peripheral device when it is ready to receive or transmit data. operating system: A group of programs that controls the basic operation of a computer. Operating system functions include interpreting programs, creating data files, and controlling the transmission and receipt (input/output) of data to and from memory and peripheral devices. output: The results of a computer operation.
TECRA M1 Version 1 Last Saved on 23.02.2003 13:48 Glossary R Radio frequency interference (RFI) shield: A metal shield enclosing the printed circuit boards of the printer or computer to prevent radio and TV interference. All computer equipment generates radio frequency signals. The FCC regulates the amount of signals a computing device can allow past its shielding. A Class A device is sufficient for office use. Class B provides a more stringent classification for home equipment use.
TECRA M1 Version 1 Last Saved on 23.02.2003 13:48 Glossary stop bit: One or more bits of a byte that follow the transmitted character or group codes in asynchronous serial communications. subpixel: Three elements, one red, one green and blue (RGB), that make up a pixel on the color LCD. The computer sets subpixels independently, each may emit a different degree of brightness. See also pixel. synchronous: Having a constant time interval between successive bits, characters or events.
TECRA M1 Version 1 Last Saved on 22.02.
TECRA M1 Version 1 Last Saved on 22.02.
TECRA M1 Version 1 Last Saved on 22.02.
TECRA M1 Version 1 Last Saved on 22.02.2003 11:49 Index Utilities 1-11 V V.90 Video RAM H-1 1-3 W Weight saver 2-21 When writing or rewriting 1-2, 4-10, 9-19 Windows special keys 5-6 Windows utilities 6-16 Windows XP Professional 1-1 Windows XP/2000 setup 3-9 Wireless communication Indicator 4-22 Wireless communication switch 4-22 Wireless communications 4-21 Wireless LAN 4-21, 9-18, J-1, K-1 kit 1-14 Work habits 3-5 Writing CDs 4-9 Tecra M1 4 ENGLISH using TecraM1online.dot –– Printed on 24.02.
