Personal Computer User Manual

ManualsBrandsToshiba ManualsDesktopTecra M10

TOSHIBA Satellite Pro M10 Series

Portable Personal Computer

Maintenance Manual

TOSHIBA CORPORATION

File Number 960-431

Summary of content (460 pages)

PAGE 1
TOSHIBA Satellite Pro M10 Series Portable Personal Computer Maintenance Manual TOSHIBA CORPORATION File Number 960-431
PAGE 2
Copyright © 2003 by TOSHIBA Corporation. All rights reserved. Under the copyright laws, this manual cannot be reproduced in any form without the prior written permission of TOSHIBA. No patent liability is assumed with respect to the use of the information contained herein. TOSHIBA Satellite Pro M10 Series Portable Personal Computer Maintenance Manual First edition February 2003 Disclaimer This manual has been validated and reviewed for accuracy.
PAGE 3
Preface This maintenance manual describes how to perform hardware service maintenance for the TOSHIBA Satellite Pro M10 Series Portable Personal Computer, referred to as Satellite Pro M10 Series in this manual. The procedures described in this manual are intended to help service technicians isolate faulty Field Replaceable Units (FRUs) and replace them in the field. SAFETY PRECAUTIONS Four types of messages are used in this manual to bring important information to your attention.
PAGE 4
The manual is divided into the following parts: Chapter 1 Hardware Overview describes the Satellite Pro M10 Series system unit and each FRU. Chapter 2 Troubleshooting Procedures explains how to diagnose and resolve FRU problems. Chapter 3 Test and Diagnostics describes how to perform test and diagnostic operations for maintenance service. Chapter 4 Replacement Procedures describes the removal and replacement of the FRUs.
PAGE 5
Conventions This manual uses the following formats to describe, identify, and highlight terms and operating procedures. Acronyms On the first appearance and whenever necessary for clarification acronyms are enclosed in parentheses following their definition. For example: Read Only Memory (ROM) Keys Keys are used in the text to describe many operations. The key top symbol as it appears on the keyboard is printed in boldface type.
PAGE 6
vi Satellite Pro M10 Series Maintenance Manual (960-431)
PAGE 7
Table of Contents Chapter 1 Hardware Overview 1.1 Features .................................................................................................................... 1-1 1.2 System Unit Block Diagram .................................................................................... 1-8 1.3 3.5-inch Floppy Disk Drive ................................................................................... 1-14 1.4 2.5-inch Hard Disk Drive........................................................
PAGE 8
Chapter 3 Tests and Diagnostics 3.1 The Diagnostic Test ................................................................................................. 3-1 3.2 Executing the Diagnostic Test ................................................................................. 3-3 3.3 Subtest Names.......................................................................................................... 3-7 3.4 System Test..................................................................................
PAGE 9
Chapter 4 Replacement Procedures 4.1 General..................................................................................................................... 4-1 4.2 Memory Modules................................................................................................... 4-12 4.3 HDD....................................................................................................................... 4-15 4.4 Slim Select Bay Module .......................................................
PAGE 10
4.32 TFT FL (Model 15.0 SXGA+ Samsung LTN150P3-L03) .................................. 4-126 4.33 TFT FL (Model 15.0 SXGA+ SHARP LQ150F1LH43)..................................... 4-136 4.34 TFT FL (Model 15.0 UXGA SHARP LQ150U1LW13)..................................... 4-154 Appendices Appendix A Handling the LCD Module ......................................................................... A-1 Appendix B Board Layout ...............................................................................
PAGE 11
Chapter 1 Hardware Overview
PAGE 12
1 Hardware Overview 1-ii Satellite Pro M10 Series Maintenance Manual (960-431)
PAGE 13
1 Hardware Overview Chapter 1 Contents 1.1 Features.......................................................................................................................1-1 1.2 System Unit Block Diagram.......................................................................................1-8 1.3 3.5-inch Floppy Disk Drive......................................................................................1-14 1.4 2.5-inch Hard Disk Drive ..........................................................
PAGE 14
1 Hardware Overview Figures Figure 1-1 Front of the computer .....................................................................................1-6 Figure 1-2 System unit configuration...............................................................................1-7 Figure 1-3 System unit block diagram .............................................................................1-8 Figure 1-4 3.5-inch FDD .............................................................................................
PAGE 15
1.1 Features 1 1 Hardware Overview Features 1.1 Features The TOSHIBA Satellite Pro M10 Series Portable Personal Computer uses extensive Large Scale Integration (LSI), and Complementary Metal-Oxide Semiconductor (CMOS) technology extensively to provide compact size, minimum weight, low power usage and high reliability. The computer is built and configured to order, to best meet the customer’s needs.
PAGE 16
1 Hardware Overview 1.1 Features CD-RW/DVD-ROM Drive A full-size, CD-RW/DVD-ROM drive module that lets the user run CD/DVDs without using an adaptor. It reads DVD-ROMs at maximum 8 speed and CD-ROMs at maximum 24 speed. It writes CD-R at up to 8 speed and CD-RW at up to 8 speed. For reading, this drive supports the same formats as the DVD-ROM drive. DVD Multi Drive A full-size DVD Multi drive enables DVD-RAM media to be read, written and erased with random access like a diskette.
PAGE 17
1.1 Features 1 Hardware Overview Sound system This computer supports software sound (AC97 Audio). The sound system is equipped with AC97 Audio, a CODEC chip, stereo speakers, an internal microphone, and jacks for headphone and external microphone. The sound system is equipped with the following: • • • • • Stereo speakers Volume control Headphone jack Internal microphone External microphone jack PC Card Slot A PC Card Slot accommodates two 5mm cards (Type II) or one 10.
PAGE 18
1 Hardware Overview 1.1 Features Parallel port A Centronics compatible parallel port enables connection of a printer or other parallel device. The port supports Extended Capabilities Port (ECP) conforming to IEEE1284. Video out This video-out mini-jack enables transfer of NTSC or PAL data (video and right/left audio) to external devices such as a TV. Internal LAN (BTO) The computer can be equipped with LAN circuits on a built-to-order basis.
PAGE 19
1.1 Features 1 Hardware Overview TOSHIBA Console button This button launches an application automatically. The default is TOSHIBA Console. TV button This button sets the display device to TV (Video-out). Press it again to return to LCD. CD/DVD Play button (provided with some models) This button directly launches various CD and DVD functions. The user can also turn on the computer’s power by holding down this button for one second and turn off the power by holding it down for 0.5 second.
PAGE 20
1 Hardware Overview 1.1 Features Docking interface port A 242-pin, docking interface port enables connection of an optional Advanced Port Replicator II. It provides additional features as follows: • • • • • • • • • • • AC adaptor One Parallel port One Serial port One PS/2 mouse port One PS/2 keyboard port One Line-in jack One Line-out jack Two USB ports (comply with USB 2.
PAGE 21
1.
PAGE 22
1 Hardware Overview 1.2 1.2 System Unit Block Diagram System Unit Block Diagram Figure 1-3 is a block diagram of the system unit. IMVP4 (Voltage Regulator) CPU: Intel Pentium M 1.3, 1.4, 1.5, 1.6 GHz ADM1032 (Thermal senser) Micro FCPGA LCD TFT 14.1" XGA 15.0" XGA 15.0" SXGA+ 15.
PAGE 23
1.2 System Unit Block Diagram 1 Hardware Overview The system unit is composed of the following major components: Processor • Intel Pentium M Processor 1.3GHz – – – – – Processor core speed: 1.3GHz at 1.35V Processor bus speed: 400MHz at 1.05V Integrated L1 cache memory: 64KB Integrated L2 cache memory: 1MB Integrated NDP • Intel Pentium M Processor 1.4GHz – – – – – Processor core speed: 1.4GHz at 1.35V Processor bus speed: 400MHz at 1.
PAGE 24
1 Hardware Overview • 1.2 System Unit Block Diagram Intel ICH4-M (I/O Controller Hub) – PCI Rev.2.2 support (6 PCI REQ/GNT pairs) – Bus master IDE controller (Ultra ATA 100/66/33) – USB 2.0 controller 6 ports (EHCI: Enhanced Host Controller) – I/O APIC – SMBus Controller – FWH I/F (BIOS) – LPC I/F (EC/KBC, Super I/O) – IRQ Controller – Serial Interrupt functions – Power Management functions – Deeper Sleep (C4) support – ACPI 1.0 support – Suspend/Resume control – AC'97 2.
PAGE 25
1.2 System Unit Block Diagram 1 Hardware Overview Card Controller: • Name: YEBISU3S • This gate array has the following functions and components. – PCI Interface (PCI Rev. 2.2) – Chipset Interface – CardBus/PC Card Controller (Yenta2 Ver. 2.2) – SD Card Controller (SDHC Ver. 1.2) – SD I/O Card Controller (Ver. 1.0) – Smart Media Controller (SMHC Ver.01/SMIL 1.0) – Smart Card I/F – SIO (UART) Controller (MS Debug Port Specification Ver. 1.
PAGE 26
1 Hardware Overview 1.2 System Unit Block Diagram KBC/EC (Keyboard Controller/Embedded Controller) • • One M306K9FCLRP chip functions as both KBC and EC. KBC has the following functions: – Scan controller to check status of keyboard matrix – Interface controller between the keyboard scan controller and the system • EC has the following functions: – Power supply sequence control – System I/F – Thermal conditions control – Flash rewriting PSC (Power Supply Controller) • One TMP87PM48U chip is used.
PAGE 27
1.2 System Unit Block Diagram 1 Hardware Overview CD Play Controller • • One OZ168 is used. The OZ168 allows music CD play while the computer is off. Sound CODEC • • One AD1981B is used. The AD1981B is an AC'97 Audio CODEC LSI, which is compliant with the industry standard "Audio CODEC '97" specification (Revision 2.3). RS232 Transceiver • • One MAX3243 chip is used.
PAGE 28
1 Hardware Overview 1.3 1.3 3.5-inch Floppy Disk Drive 3.5-inch Floppy Disk Drive The external USB 3.5-inch FDD is a thin, high-performance reliable drive that supports 720KB (formatted) 2DD and 1.44MB (formatted) 2HD disks. The FDD is shown in Figure 1-4. The specifications for the FDD are listed in Table 1-1. Figure 1-4 3.5-inch FDD Table 1-1 3.
PAGE 29
1.4 2.5-inch Hard Disk Drive 1.4 1 Hardware Overview 2.5-inch Hard Disk Drive The removable HDD is a random-access, non-volatile storage device. It has a non-removable 2.5-inch magnetic disk and mini-Winchester type magnetic heads. The computer supports a 30, 40, or 60GB HDD. The HDD is shown in figure 1-5. Specifications are listed in Table 1-2. Figure 1-5 2.5-inch HDD Table 1-2 2.5-inch HDD specifications TOSHIBA MK3021GAS TOSHIBA MK4021GAS TOSHIBA MK4019GAX HITACHI DK23EA-30 (30.
PAGE 30
1 Hardware Overview 1.5 1.5 DVD-ROM Dvive DVD-ROM Drive The DVD-ROM drive is capable of driving either 12cm (4.72-inch) or 8cm (3.15-inch) DVD/CDs without an adaptor. It reads DVDs at maximum 8-speed and reads CDs at maximum 24-speed. The DVD-ROM drive is shown in Figure 1-6. Specifications for the DVD-ROM drive are listed in Table 1-3. Figure 1-6 DVD-ROM drive Table 1-3 DVD-ROM drive specifications Item DVD-ROM mode ATAPI Burst (Mbytes/s) CD-ROM mode 33.3 (Ultra DMA) 16.
PAGE 31
1.6 Multi Drive 1.6 1 Hardware Overview Multi Drive The Multi drive accommodates either 12cm (4.72-inch) or 8cm (3.15-inch) CDs and CDR/RWs or DVDs. It reads DVDs at a maximum 8-speed and CDs at a maximum 24-speed. The Multi drive is shown in Figure 1-7. Specifications for the Multi drive are listed in Table 1-4.
PAGE 32
1 Hardware Overview 1.6 Multi Drive Table 1-4 Multi drive specifications (2/2) TEAC DW-224E-36 Item ATAPI Burst (Mbytes/s) Access time (ms) Average 1/3 Stroke Access Data Buffer Capacity (Mbytes) Supported Format DVD-ROM (Play mode) CD-ROM (Play mode) 33.3 (Ultra DMA mode 2) 16.
PAGE 33
1.7 DVD Multi Drive 1.7 1 Hardware Overview DVD Multi Drive The DVD Multi drive (Panasonic UJ-810BTJ7-A) is capable of driving either 12cm (4.72inch) or 8cm (3.15-inch) DVD/CDs without an adaptor. The DVD Multi drive is shown in Figure 1-8. Specifications for the DVD Multi drive are listed in Table 1-5. Figure 1-8 DVD Multi drive Table 1-5 DVD Multi drive specifications Item ATAPI Burst (Mbytes/s) Access time (ms) Random Access (Ave.) Random Seek (Ave.) Full Stroke Access (Ave.
PAGE 34
1 Hardware Overview 1.8 1.8 Power Supply Power Supply The power supply distributes 11 different voltages to the system board and performs the following functions: 1.
PAGE 35
1.8 Power Supply 1 Hardware Overview 6. Power ON/OFF sequence When power is turned on or off, the PSC starts the power on or off sequence. • SQ0-4 = power ON sequence • SQ5-B = power OFF sequence 7. Battery charging control The PSC controls the following. • The quick charge ON/OFF • The trickle charge ON/OFF • The detection of full charge 8. Detection of the low battery The PSC detects the low battery point by the battery voltage, current and temperature.
PAGE 36
1 Hardware Overview 1.8 Power Supply The power supply output rating is specified in Table 1-6. Table 1-6 Power supply board output rating Power supplied Yes/No Name Voltage (V) Stand by CPU (core) PPV 1.3 No No No CPU (bus), MCH-M, ICH4-M PTV 1.075 No No No VGAC BGV 1.35 Yes No No HDD, Keyboard, Touch Pad, Accupoint, Mini PCI, Bluetooth, FL P5V 5.0 No No No ICH4-M, FWH, Clock Generator, ADM1032AR, SD Card, Mini PCI, Super I/O, FIR, IEEE 1394, LCD, CODEC P3V 3.
PAGE 37
1.9 Batteries 1.9 1 Hardware Overview Batteries The computer has three types of batteries: Main battery pack Optional secondary battery pack (installed in the Slim Select Bay) RTC battery The battery specifications are listed in Table 1-7. Table 1-7 Battery specifications Battery name Material Output voltage Capacity Main battery Lithium-Ion 10.8 V 6,600 mAh or 4400mAH Secondary battery Lithium-Ion 10.8 V 3,600 mAh RTC battery Lithium-Ion 3.0 V 17mAh 1.9.
PAGE 38
1 Hardware Overview 1.9 Batteries 1.9.3 Battery Charging Control Battery charging is controlled by a power supply microprocessor mounted on the system board. The power supply microprocessor controls whether the charge is on or off and detects a full charge when the AC adaptor and battery are attached to the computer. The system charges the battery using quick charge or trickle charge. Battery Charge When the AC adaptor is attached, battery charge starts.
PAGE 39
1.9 Batteries 1 Hardware Overview Detection of full charge A full charge is detected when the battery is charging, and under any of the following conditions: 1. The battery charging current drops under the predetermined limit. 2. The charging time exceeds the limit. 3. The battery’s temperature exceeds 60°C. 1.9.4 RTC battery The RTC battery provides power to keep the current date, time and other setup information in memory while the computer is turned off.
PAGE 40
1 Hardware Overview 1-26 1.
PAGE 41
Chapter 2 Troubleshooting Procedures
PAGE 42
2 Troubleshooting Procedures 2-ii Satellite Pro M10 Series Maintenance Manual (960-431)
PAGE 43
2 Troubleshooting Procedures Chapter 2 Contents 2.1 Troubleshooting ......................................................................................................... 2-1 2.2 Troubleshooting Flowchart........................................................................................ 2-3 2.3 Power Supply Troubleshooting ................................................................................. 2-7 2.4 2.5 2.6 2.7 2.8 Procedure 1 Power Status Check ...........................
PAGE 44
2 Troubleshooting Procedures Procedure 3 2.9 2.10 2.11 2.12 2.13 2.14 2-iv Connector and Replacement Check ........................................... 2-42 Optical Disk Drive Troubleshooting........................................................................ 2-43 Procedure 1 Drive Cleaning Check................................................................ 2-43 Procedure 2 Diagnostic Test Program Execution Check ...............................
PAGE 45
2 Troubleshooting Procedures Figures Figure 2-1 Troubleshooting flowchart............................................................................. 2-4 Figure 2-2 Printer port LED .......................................................................................... 2-21 Tables Table 2-1 Battery LED ................................................................................................... 2-7 Table 2-2 DC IN LED ........................................................................
PAGE 46
2 Troubleshooting Procedures 2-vi Satellite Pro M10 Series Maintenance Manual (960-431)
PAGE 47
2.1 Troubleshooting 2 Troubleshooting Procedures 2 2.1 Troubleshooting Chapter 2 describes how to determine if a Field Replaceable Unit (FRU) in the computer is causing the computer to malfunction. The FRUs covered are: 1. System Board 5. Display 9. Sound components 2. Floppy Disk Drive 6. Optical Disk Drive 10. Bluetooth 3. Hard Disk Drive 7. Modem 11. Wireless LAN 4. Keyboard 8. LAN The Diagnostics Disk operations are described in Chapter 3.
PAGE 48
2 Troubleshooting Procedures 2.1 Troubleshooting 20. CD-RW media that supports four-speed writing and is formatted with DirectCD (media manufactured by RICOH or Mitsubishi Chemical are recommended). 21. RJ11 connector checker and modular cable or RJ11 connector checker LED 22. LAN wraparound connector 23. Music CD 24.
PAGE 49
2.2 Troubleshooting Flowchart 2.2 2 Troubleshooting Procedures Troubleshooting Flowchart Use the flowchart in Figure 2-1 as a guide for determining which troubleshooting procedures to execute. Before going through the flowchart steps, verify the following: Ask the user if a password is registered and, if it is, ask him or her to enter the password.
PAGE 50
2 Troubleshooting Procedures 2.2 Troubleshooting Flowchart START Connect the AC adaptor to the DC IN socket. Does the DC IN LED glow? No Perform the Power Supply Troubleshooting Procedures in section 2.3. No Perform the Power Supply Troubleshooting Procedures in section 2.3. Yes Perform the Power Supply Troubleshooting Procedures in section 2.3. Yes Perform the System Board Troubleshooting Procedures in section 2.4. No Perform the Display Troubleshooting Procedures in section 2.8.
PAGE 51
2.2 Troubleshooting Flowchart 2 Troubleshooting Procedures 1 Do typed characters appear correctly? No Perform the Keyboard Troubleshooting Procedures in section 2.7. No Perform the Floppy Disk Drive Troubleshooting Procedures in section 2.5. Yes Insert the diagnostics disk into the FDD, then run the diagnostics test program. Is the diagnostics test loaded? Yes Perform each test.
PAGE 52
2 Troubleshooting Procedures 2.2 Troubleshooting Flowchart If the diagnostics program cannot detect an error, the problem may be intermittent. The Running Test program should be executed several times to isolate the problem. Check the Log Utilities function to confirm which diagnostic test detected an error, then perform the appropriate troubleshooting procedures as follows: 1.
PAGE 53
2.3 Power Supply Troubleshooting 2.3 2 Troubleshooting Procedures Power Supply Troubleshooting The power supply controls many functions and components. To determine if the power supply is functioning properly, start with Procedure 1 and continue with the other Procedures as instructed.
PAGE 54
2 Troubleshooting Procedures 2.3 Power Supply Troubleshooting Table 2-2 DC IN LED DC IN LED Power supply status Lights green DC power is being supplied from the AC adaptor. Blinks orange Power supply malfunction*3 Doesn’t light Any condition other than those above. *3 When the power supply controller detects a malfunction, the DC IN LED blinks and an error code is displayed. To check the power supply status, install a battery pack and connect an AC adaptor.
PAGE 55
2.3 Power Supply Troubleshooting Procedure 2 2 Troubleshooting Procedures Error Code Check If the power supply microprocessor detects a malfunction, the DC IN LED blinks orange. The blink pattern indicates an error as shown below. Start Off for 2 seconds Error code (8 bit) “1” On for one second “0” On for a half second Interval between data bits Off for a half second The error code begins with the least significant digit. Example: Error code 12h (Error codes are given in hexadecimal format.
PAGE 56
2 Troubleshooting Procedures 2.3 Power Supply Troubleshooting 1st Battery Error code Meaning 20h Main battery overvoltage is detected. (Not supported) 21h Main battery charge current is more than 6.05 A. 22h Main battery discharge current is more than 0.5 A when there is no load. 23h Main battery charge current is more than 4.3 A when DC IN direct charge is off. 24h Current sensing IC is not normal. 25h Main battery charge current is more than 0.3A when the battery isn't being charged.
PAGE 57
2.3 Power Supply Troubleshooting 2 Troubleshooting Procedures 1R5-C1V output Error code Meaning 50h 1R5-C1V voltage is over 1.80V when the computer is powered on or off. 51h 1R5-C1V voltage is less than 1.275V when the computer is powered on. 52h 1R5-C1V voltage is less than 1.275V when the computer is booting up. 53h 1R5-C1V voltage is less than 1.275V when the computer is suspended. 54h 1R5-C1V voltage is abnormal when the computer is shutting down. 55h 1R5-C1V voltage is less than 1.
PAGE 58
2 Troubleshooting Procedures 2.3 Power Supply Troubleshooting BGVSNS-B1P output Error code Meaning 80h BGVSNS-B1P voltage is over 1.62V when the computer is powered on or off. 81h BGVSNS-B1P voltage is less than 0.68V when the computer is powered on. 82h BGVSNS-B1P voltage is less than 0.68V when the computer is booting up. 83h BGVSNS-B1P voltage is more than 0.68V when the computer is powered off. 84h BGVSNS-B1P voltage is less than 0.68V when the computer is suspended.
PAGE 59
2.3 Power Supply Troubleshooting 2 Troubleshooting Procedures 1R2-P1V output Error code Meaning B0h 1R2-P1V voltage is more than 1.44V when the computer is powered on or off. B1h 1R2-P1V voltage is less than 1.02V when the computer is powered on. B2h 1R2-P1V voltage is less than 1.02V when the computer is booting up. B3h 1R2-P1V voltage is more than 1.02V when the computer is powered off. 2R5-B2V output Error code Meaning C0h 2R5-B2V voltage is more than 3.
PAGE 60
2 Troubleshooting Procedures Check 2 2.3 Power Supply Troubleshooting In the case of error code 10h or 12h: Make sure the AC adaptor cord and AC power cord are firmly plugged into the DC IN 15 V socket and wall outlet. If the cables are connected correctly, go to the following step: Connect a new AC adaptor and/or AC power cord, if necessary. If the error still exists, go to Procedure 5. Check 3 In the case of error code 2Xh or 3Xh: Make sure the battery pack is correctly installed in the computer.
PAGE 61
2.3 Power Supply Troubleshooting Procedure 3 2 Troubleshooting Procedures Connection Check The power supply wiring diagram is shown below: AC adaptor cord AC adaptor DC-IN Jack PJ8800 System board PJ117 PJ8810 Main battery pack AC power cord Slim Select Bay 2nd battery pack Any of the connectors may be disconnected. Perform Check 1. Check 1 Disconnect the AC power cord from wall outlet. Check the power cable for breaks. If the power cord is damaged, connect a new AC power cord.
PAGE 62
2 Troubleshooting Procedures Procedure 4 2.3 Power Supply Troubleshooting Quick Charge Check The power supply may not charge the battery pack. Perform the following procedures: 1. Reinstall the battery pack. 2. Attach the AC adaptor and turn on the power. If you cannot turn on the power, go to Procedure 5. 3. Run the Diagnostic test, go to System test and execute subtest 06 (quick charge) described in Chapter 3. 4. When quick charge is complete, the diagnostics test displays the result code.
PAGE 63
2.3 Power Supply Troubleshooting Procedure 5 2 Troubleshooting Procedures Replacement Check The system board may be disconnected or damaged. Disassemble the computer following the steps described in Chapter 4, Replacement Procedures, and perform the following Check 1: Check 1 Replace the AC adaptor with a new one. If the AC adaptor is still not functioning properly, perform Check 2. Check 2 Use a multimeter to make sure that F8800, F8801, F8810 and F8820 fuses on the system board are not blown.
PAGE 64
2 Troubleshooting Procedures 2.4 2.4 System Board Troubleshooting System Board Troubleshooting This section describes how to determine if the system board is defective or not functioning properly. Start with Procedure 1 and continue with the other procedures as instructed.
PAGE 65
2.4 System Board Troubleshooting Procedure 1 2 Troubleshooting Procedures Message Check When the power is turned on, the system performs the Initial Reliability Test (IRT) installed in the BIOS ROM. The IRT tests each IC on the system board and initializes it. If an error message is shown on the display, perform Check 1. If there is no error message, go to Procedure 2. If TOSHIBA MS-DOS or TOSHIBA Windows XP is properly loaded, go to Procedure 3.
PAGE 66
2 Troubleshooting Procedures Check 2 2.4 System Board Troubleshooting The IRT checks the system board. When the IRT detects an error, the system stops or an error message appears. If one of the following error messages (1) through (17), (24) or (25) displays, go to Procedure 4. If error message (18) displays, go to the Keyboard Troubleshooting Procedures in Section 2.7. If error message (19) or (20) displays, go to the HDD Troubleshooting Procedures in Section 2.6.
PAGE 67
2.4 System Board Troubleshooting Procedure 2 2 Troubleshooting Procedures Printer Port LED Check on Boot Mode The printer port LED displays the IRT status and test status by turning lights on and off as an eight-digit binary value for boot mode. Figure 2-2 shows the printer port LED. Figure 2-2 Printer port LED To use the printer port LED follow the steps below: 1. Plug the printer port LED into the computer’s parallel port. 2. Turn on the computer’s power. 3.
PAGE 68
2 Troubleshooting Procedures 2.4 System Board Troubleshooting Table 2-3 Printer port LED boot mode status (1/6) LED Status Test item Message FFh Start Register initialization for boot block B0h Flash ROM check PIT ch.
PAGE 69
2.
PAGE 70
2 Troubleshooting Procedures 2.
PAGE 71
2.
PAGE 72
2 Troubleshooting Procedures 2.
PAGE 73
2.
PAGE 74
2 Troubleshooting Procedures Check 1 2.4 System Board Troubleshooting If any of the following error codes display, go to Procedure 4. B0h, B1h, B2h, B3h, B7h, B8h, 00h, 01h, 02h, 03h, 04h, 06h, 07h, 05h, D0h, D1h, D2h, D3h, D4h, D5h, 70h, 74h, 75h, 71h, 72h, 73h, 76h, 77h, 81h, 82h, 83h, 78h, 79h, 08h, 09h, 0Ah, 0Dh, 18h, 19h, 1Fh, 20h, 25h, 30h, 40h, 41h, 22h, 42h, 80h, 83h, C0h, C1h, A6h Check 2 If error codes 81h or 82h are displayed, go to the following sections: Section 2.
PAGE 75
2.4 System Board Troubleshooting Procedure 3 2 Troubleshooting Procedures Diagnostic Test Program Execution Check Execute the following tests from the Diagnostic Test Menu. Refer to Chapter 3, Tests and Diagnostics, for more information on how to perform these tests. 1. System test 2. Memory test 3. Keyboard test 4. Display test 5. Floppy Disk test 6. Printer test 7. Hard Disk test 8. Real Timer test 9. NDP test 10. Expansion test 11. Sound test 12. CD-ROM/DVD-ROM test 13.
PAGE 76
2 Troubleshooting Procedures 2.5 2.5 FDD Troubleshooting FDD Troubleshooting This section describes how to determine if the FDD is functioning properly. Perform the steps below starting with Procedure 1 and continuing with the other procedures as required. Procedure 1: FDD Head Cleaning Check Procedure 2: Diagnostic Test Program Execution Check Procedure 3: Connector Check and Replacement Check Procedure 1 FDD Head Cleaning Check FDD head cleaning is one option available in the Diagnostic Program.
PAGE 77
2.5 FDD Troubleshooting Procedure 2 2 Troubleshooting Procedures Diagnostic Test Program Execution Check Insert the Diagnostics Disk in the FDD, turn on the computer and run the test. Refer to Chapter 3, Tests and Diagnostics, for more information about the diagnostics test procedures. Floppy disk drive test error codes and their status names are listed in Table 2-4. Make sure the floppy disk is formatted correctly and that the write protect tab is disabled.
PAGE 78
2 Troubleshooting Procedures Procedure 3 2.5 FDD Troubleshooting Connector Check and Replacement Check The 3.5-inch FDD is connected to the USB board. Check 1 Make sure that the FDD cable is firmly connected to the USB port, and that the USB board is firmly connected to the system board. FDD PJ2033 USB Board (FQDUS*) PJ2042 PJ2040 System Board (FQDSY*) FDD cable If any of the connections are loose, reconnect firmly and repeat Procedure 2.
PAGE 79
2.6 HDD Troubleshooting 2.6 2 Troubleshooting Procedures HDD Troubleshooting This section describes how to determine if the HDD is functioning properly. Perform the steps below starting with Procedure 1 and continuing with the other procedures as required.
PAGE 80
2 Troubleshooting Procedures Procedure 2 2.6 HDD Troubleshooting Partition Check Insert the TOSHIBA MS-DOS system disk and restart the computer. Perform the following checks: Check 1 Type C: and press Enter. If you cannot change to drive C, go to Check 2. If you can change to drive C, go to Check 3. Check 2 Type FDISK and press Enter. Choose Display Partition Information from the FDISK menu. If drive C is listed, go to Check 3.
PAGE 81
2.6 HDD Troubleshooting Procedure 3 2 Troubleshooting Procedures Format Check The computer’s HDD is formatted using the MS-DOS FORMAT program. To format the HDD, follow the steps below. Check 1 Format the HDD and transfer system files using FORMAT C:/S/U. If the following message appears on the display, the HDD is formatted. Format complete If an error message appears on the display, go to Procedure 4.
PAGE 82
2 Troubleshooting Procedures Procedure 4 2.6 HDD Troubleshooting Diagnostic Test Program Execution Check The HDD test program is stored in the diagnostics disk. Perform all of the HDD tests in the Hard Disk Drive Test. Refer to Chapter 3, Tests and Diagnostics, for more information about the HDD test program. If an error is detected during the HDD test, an error code and status will be displayed. The error codes and statuses are listed in Table 2-5.
PAGE 83
2.6 HDD Troubleshooting Procedure 5 2 Troubleshooting Procedures Connector Check and Replacement Check The HDD or the system board may be disconnected or damaged. Disassemble the computer following the steps described in Chapter 4, Replacement Procedures and perform the following checks: Check 1 Make sure the HDD is firmly connected to PJ1509 on the system board. HDD PJ1509 System board If the connections are loose, reconnect firmly and repeat Procedure 1. If there is still an error, go to Check 2.
PAGE 84
2 Troubleshooting Procedures 2.7 2.7 Keyboard Troubleshooting Keyboard Troubleshooting To determine if the computer’s keyboard is functioning properly, perform the following procedures. Start with Procedure 1 and continue with the other procedures as instructed.
PAGE 85
2.7 Keyboard Troubleshooting Procedure 3 2 Troubleshooting Procedures Connector and Replacement Check The keyboard, Touch pad, switch board or system board may be disconnected or damaged. Disassemble the computer following the steps described in Chapter 4, Replacement Procedures and perform the following checks. If the keyboard malfunctions, start with Check 1.If the Touch pad malfunctions, start with Check 3. If the switch board malfunctions, start with Check 5.
PAGE 86
2 Troubleshooting Procedures Check 5 2.7 Keyboard Troubleshooting Make sure the switch board I/F cable is firmly connected to the system board and to the switch board. Switch board PJ2025 System board Switch board I/F cable If any of the connections are loose, reconnect firmly and repeat Procedure 1. If there is still an error, go to Check 6. Check 6 The switch board or the I/F cable may be damaged. Replace them with new ones following the instructions in Chapter 4.
PAGE 87
2.8 Display Troubleshooting 2.8 2 Troubleshooting Procedures Display Troubleshooting This section describes how to determine if the computer’s display is functioning properly. Start with Procedure 1 and continue with the other procedures as instructed.
PAGE 88
2 Troubleshooting Procedures Procedure 3 2.8 Display Troubleshooting Connector and Replacement Check The FL, FL inverter board, LCD module, and system board are connected to the display circuits. Any of these components may be damaged. Refer to Chapter 4, Replacement Procedures, for instructions on how to disassemble the computer and then perform the following checks: If the FL does not light, perform Check 1. If characters or graphics are not displayed clearly, perform Check 3.
PAGE 89
2.9 Optical Disk Drive Troubleshooting 2.9 2 Troubleshooting Procedures Optical Disk Drive Troubleshooting This section describes how to determine if the computer’s internal optical disk drive (CD-R/RW drive, DVD-ROM drive, Multi drive, DVD-R/-RW drive or DVD-RAM drive) is functioning properly. Perform the steps below starting with Procedure 1 and continue with the other procedures as required.
PAGE 90
2 Troubleshooting Procedures Procedure 3 2.9 Optical Disk Drive Troubleshooting Connector Check and Replacement Check The optical disk drive is installed in the system board. The drive may be disconnected, or the drive or system board may be damaged. Disassemble the computer following the steps described in Chapter 4, Replacement Procedures and perform the following checks: Check 1 Make sure the drive is properly installed in the Slim Select Bay of the computer.
PAGE 91
2.10 Modem Troubleshooting 2 Troubleshooting Procedures 2.10 Modem Troubleshooting This section describes how to determine if the computer's modem is functioning properly. Perform the steps below starting with Procedure 1 and continuing with the other procedures as required.
PAGE 92
2 Troubleshooting Procedures Procedure 2 2.10 Modem Troubleshooting Connector Check and Replacement Check The Modem is installed as a modem daughter card (MDC). If the modem malfunctions, there may be a bad connection between the MDC and the system board. Or the MDC, the system board or their connectors might be damaged.
PAGE 93
2.11 LAN Troubleshooting 2 Troubleshooting Procedures 2.11 LAN Troubleshooting This section describes how to determine if the computer's LAN port is functioning properly. Perform the steps below starting with Procedure 1 and continuing with the other procedure as required. Procedure 1: Diagnostic Test Program Execution Check Procedure 2: Connector Check and Replacement Check Procedure 1 Diagnostic Test Program Execution Check The LAN Diagnostic test program is stored on the computer's diagnostic disk.
PAGE 94
2 Troubleshooting Procedures Procedure 2 2.11 LAN Troubleshooting Connector Check and Replacement Check If the LAN port malfunctions, there may be a bad connection between the RJ-45/RJ-11 jacks and the System Board. Or the System Board may be damaged. Disassemble the computer following the steps described in Chapter 4, Replacement Procedures and perform the following checks: Check 1 Make sure the RJ-45/RJ-11 jacks are firmly connected to system board PJ124.
PAGE 95
2.12 Sound Troubleshooting 2 Troubleshooting Procedures 2.12 Sound Troubleshooting This section describes how to determine if the computer's sound functions are functioning properly. Perform the steps below starting with Procedure 1 and continuing with the other procedures as required.
PAGE 96
2 Troubleshooting Procedures Procedure 2 2.12 Sound Troubleshooting Connector Check The sound function wiring diagram is shown below: Right speaker cable Sound board PJ5007 PJ5002 PJ5006 System board PJ5004 Right Speaker PJ5005 Left Speaker Left speaker cable Internal Mic. Any of the connections may be disconnected.
PAGE 97
2.12 Sound Troubleshooting Procedure 3 2 Troubleshooting Procedures Replacement Check Check 1 If the stereo speakers don't sound properly, the stereo speakers may be defective or damaged. Replace them with new ones. If the stereo speakers still do not work properly, go to Check 3. Check 2 If the internal microphone does not work correctly, the internal microphone may be defective or damaged. Replace it with a new one. If the internal microphone still does not work correctly, go to Check 3.
PAGE 98
2 Troubleshooting Procedures 2.13 Bluetooth Troubleshooting 2.13 Bluetooth Troubleshooting This section describes how to determine if the computer's Bluetooth functions are working properly. Perform the steps below starting with Procedure 1 and continuing with the other procedure as required.
PAGE 99
2.13 Bluetooth Troubleshooting Procedure 2 2 Troubleshooting Procedures Connector Check and Replacement Check If the Bluetooth function malfunctions, there may be a bad connection between the antenna cable, the Bluetooth module, and the system board (FQDSY*). Or the antenna cable or other boards may be damaged. Disassemble the computer following the steps described in Chapter 4, Replacement Procedures and perform the following checks: Check 1 The Bluetooth function wiring diagram is shown below.
PAGE 100
2 Troubleshooting Procedures 2.14 Wireless LAN Troubleshooting 2.14 Wireless LAN Troubleshooting This section describes how to determine if the computer's Wireless LAN is functioning properly. Perform the steps below starting with Procedure 1 and continuing with the other procedure as required.
PAGE 101
2.14 Wireless LAN Troubleshooting Procedure 2 2 Troubleshooting Procedures Connector Check and Replacement Check If the Wireless LAN port malfunctions, there may be a bad connection between the antenna boards, the Wireless LAN Mini PCI card, and the system board (FQDSY*). Or the antenna board, the Mini PCI card, or the system board may be damaged.
PAGE 102
2 Troubleshooting Procedures 2-56 2.
PAGE 103
Chapter 3 Tests and Diagnostics
PAGE 104
3 Tests and Diagnostics 3-ii Satellite Pro M10 Series Maintenance Manual (960-431)
PAGE 105
3 Tests and Diagnostics Chapter 3 Contents 3.1 The Diagnostic Test ................................................................................................... 3-1 3.2 Executing the Diagnostic Test ................................................................................... 3-3 3.3 Subtest Names............................................................................................................ 3-7 3.4 System Test................................................................
PAGE 106
3 Tests and Diagnostics 3.25.2 3.26 3.27 3.28 Operations .......................................................................................... 3-69 Floppy Disk Drive Utilities...................................................................................... 3-71 3.26.1 Function Description .......................................................................... 3-71 3.26.2 Operations ..........................................................................................
PAGE 107
3.1 The Diagnostic Test 3 Tests and Diagnostics 3 3.1 The Diagnostic Test This chapter explains how to use the Diagnostic Test program to test the functions of the computer’s hardware modules. The Diagnostic Test Program is stored on the Diagnostic Disk. The Diagnostic Test program consists of eight programs that are grouped into the Service Program Module (DIAGNOSTIC TEST MENU). NOTE: To start the diagnostics, follow these steps: 1. Check all cables for loose connections. 2.
PAGE 108
3 Tests and Diagnostics 3.1 The Diagnostic Test You will need the following equipment to perform some of the Diagnostic test programs. The Diagnostics Disk (all tests) A formatted working disk for the floppy disk drive test An external FDD attachment A cleaning kit to clean the floppy disk drive heads (Head Cleaning) A cleaning kit to clean the DVD-ROM drive heads (Head Cleaning) A PC card wraparound connector for the I/O card test (Expansion test) (Rev.
PAGE 109
3.2 Executing the Diagnostic Test 3.2 3 Tests and Diagnostics Executing the Diagnostic Test Toshiba MS-DOS is required to run the DIAGNOSTICS TEST PROGRAM. To start the DIAGNOSTIC TEST PROGRAM, follow these steps: 1. Insert the Diagnostics disk in the floppy disk drive and turn on the computer while pressing U. (The Diagnostics Disk contains the MS-DOS boot files.) NOTE: To execute the CD-ROM or DVD-ROM test, make sure the CD-ROM and CDROM drive or DVD-ROM and DVD-ROM drive is installed in the computer.
PAGE 110
3 Tests and Diagnostics 3.2 Executing the Diagnostic Test 2. To execute the DIAGNOSTIC TEST MENU from the DIAGNOSTICS MENU, set the highlight bar to 1, and press Enter. The following DIAGNOSTIC TEST MENU will appear: TOSHIBA Personal Computer xxxxxxx DIAGNOSTICS Version X.XX (C) Copyright TOSHIBA Corp.
PAGE 111
3.2 Executing the Diagnostic Test 3 Tests and Diagnostics 3. Select the option you want to execute and press Enter. When “1-SYSTEM TEST” is selected, the following message will appear: SYSTEM TEST SUB-TEST : PASS COUNT: WRITE DATA: ADDRESS : XXXXXXX XX XXXXX XX XXXXX xxxxxxx DIAGNOSTIC TEST VX.
PAGE 112
3 Tests and Diagnostics 3.2 Executing the Diagnostic Test 5. The following message will appear: ERROR STOP : YES/NO Then, use the left or right arrow keys to move the cursor to the desired option and press Enter. Selecting YES stops the test program when an error is found and displays the operation guide on the right side of the display screen as shown below: ERROR STATUS NAME [[ HALT OPERATION ]] 1: Test end 2: Continue 3: Retry These three selections have the following functions respectively: 1.
PAGE 113
3.3 Subtest Names 3.3 3 Tests and Diagnostics Subtest Names Table 3-1 lists the subtest names for each test program in the DIAGNOSTIC TEST MENU. Table 3-1 Subtest names (1/3) No. Test Name Subtest No.
PAGE 114
3 Tests and Diagnostics 3.3 Subtest Names Table 3-1 Subtest names (2/3) No. 3-8 Test Name Subtest No.
PAGE 115
3.3 Subtest Names 3 Tests and Diagnostics Table 3-1 Subtest names (3/3) No. Test Name Subtest No.
PAGE 116
3 Tests and Diagnostics 3.4 3.4 System Test System Test To execute the System Test select 1 from the DIAGNOSTIC TEST MENU, press Enter and follow the directions on the screen. Move the highlight bar to the subtest you want to execute and press Enter. Subtest 01 ROM Checksum This subtest executes a checksum test of the BIOS ROM on the System Board. Subtest 02 Dock/Undock Subtest 04 Fan On/Off This subtest checks CPU fan operation using the on/off command.
PAGE 117
3.4 System Test Subtest 07 3 Tests and Diagnostics DMI read Reads the factory setting for the serial and DMI numbers. Model Name Version Number Serial Number Model Number PCN/BND Number UUID Number : : : : : : XXXXXX XXXXXX-XXXXX XXXXXXXXXX XXXXXX-XXXXX XXXXXXXXXXXXXXXXXXXX XXXXXXXXXXXXXXXXXXXXXXXXX To exit this subtest and return to the SYSTEM TEST menu, press Enter. Subtest 08 DMI write The following messages appear in order. When this subtest is executed. Input each information.
PAGE 118
3 Tests and Diagnostics Subtest 10 3.4 System Test CPU Temperature This subtest measures the CPU temperature to see if the cooling functions of the computer are effectively working. When the subtest starts, the following message appears on the display: CPU TEMP = XX deg C Throttling level = XXXXh The number of the CPU TEMP indicates the CPU temperature at the moment in decimal notation. For example, if the number is 57, the CPU temperature is 57 degrees.
PAGE 119
3.5 Memory Test 3.5 3 Tests and Diagnostics Memory Test To execute the Memory Test, select 2 from the DIAGNOSTIC TEST MENU, press Enter and follow the directions on the screen. Move the highlight bar to the subtest you want to execute and press Enter. Subtest 01 Conventional memory This subtest writes constant data to conventional memory (0 to 640 KB), then reads the new data and compares the result with the original data. Subtest 02 Protected Mode NOTE: The CONFIG.
PAGE 120
3 Tests and Diagnostics Subtest 04 3.5 Memory Test Cache Memory To test the cache memory, a pass-through write-read comparison of ‘5A’ data is run repeatedly to the test area (‘7000’:‘Program’ size to ‘7000’:‘7FFF’ (32 KB)) to check the hit-miss ratio (on/off status) for CPU cache memory. One test takes 3 seconds.
PAGE 121
3.6 Keyboard Test 3.6 3 Tests and Diagnostics Keyboard Test To execute the Keyboard Test, select 3 from the DIAGNOSTIC TEST MENU, press Enter and follow the directions on the screen. Move the highlight bar to the subtest you want to execute and press Enter. Subtest 01 Pressed Key Display NOTE: The Num Lock and the Overlay mode must be off to execute this subtest. When you execute this subtest, the keyboard layout is drawn on the display as shown below.
PAGE 122
3 Tests and Diagnostics Subtest 02 3.6 Keyboard Test Pressed Key Code Display When a key is pressed, the scan code, character code, and key top name are displayed on the screen in the format shown below. The Ins, Caps Lock, Num Lock, Scroll Lock, Alt, Ctrl, Left Shift, and Right Shift keys are displayed in reverse screen mode when pressed. The scan codes, character codes, and key top names are shown in Appendix D.
PAGE 123
3.6 Keyboard Test Subtest 04 3 Tests and Diagnostics Touch Pad This Subtest checks the functions of the touch pad as shown below. A) Touch Pad pressure sensing direction and parameter. B) Touch Pad switch function check. This test reports the pointing stick motion response from the touch pad and touch pad switch. When the touch pad is pressed towards the upper left, the display changes according to the following illustration. If a touch pad switch is pressed, the
PAGE 124
3 Tests and Diagnostics Subtest 05 3.6 Keyboard Test USB Test ( Port0,Port1 ) test This Subtest checks USB. The USB TEST Module (ZD0003P01) and USB Cable (ZD0003P02) must be connected to the computer. The following message will appear. Select a port to test and press Enter. Test port number select (1:Port0, 2:Port1, 3:Port0&1) ? If the test ends successfully, OK is displayed. If nothing is displayed, there may be a problem with the USB port. Check the wraparound connection and repeat the test.
PAGE 125
3.6 Keyboard Test Subtest 07 3 Tests and Diagnostics Button Test When this subtest displays messages shown below in order, press the corresponding button. NOTE: This subtest must be completed within 10 seconds. Press Press Press Press Press Press Press Press Press Subtest 08 [CD] button [MP3] button [Back] button [Play] button [Stop] button [Next] button [IE] button [Mail] button [TV] button IPS This Subtest checks the functions of the accupoint.
PAGE 126
3 Tests and Diagnostics 3.7 3.7 Display Test Display Test To execute the Display Test, select 4 from the DIAGNOSTIC TEST MENU, press Enter and follow the directions on the screen. The Display test contains seven subtests that test the display in various modes. Move the highlight bar to the subtest you want to execute and press Enter. Subtest 01 VRAM Read/Write for VGA This subtest writes constant data AAh and 55h and address data to video RAM 8MB.
PAGE 127
3.7 Display Test Subtest 04 3 Tests and Diagnostics Gradation & Mode test for VGA This subtest displays gradations for each mode. Execute the test, then press Enter to change the mode. The display below appears on the screen when this subtest is executed. Pressing Enter changes the size of the displayed image. [ Mode 12 ] Pressing Enter changes the size of the displayed image.
PAGE 128
3 Tests and Diagnostics 3.7 Display Test Pressing Enter changes the size of the displayed image. [ Mode 3 ] Pressing Enter changes the size of the displayed image in the following order: Mode 111 Mode 112 Mode 114 Mode 115 Mode 117 640*480 640*480 800*600 800*600 1024*768 64K 16M 64K 16M 64K [Mode 111 640*480 64K] To exit this subtest and return to the DISPLAY TEST menu, press Ctrl + Break.
PAGE 129
3.7 Display Test Subtest 06 3 Tests and Diagnostics “H” Pattern Display This subtest displays a full screen of “H” patterns.
PAGE 130
3 Tests and Diagnostics 3.8 3.8 Printer Test Printer Test To execute the Printer Test, select 6 from the DIAGNOSTIC TEST MENU, press Enter and follow the directions on the screen. The Printer Test contains three subtests that test the output of the printer connected to the computer. The following messages will appear after selecting the Printer Test from the DIAGNOSTIC TEST MENU. Answer each of the questions with an appropriate response to execute the test.
PAGE 131
3.8 Printer Test Subtest 02 3 Tests and Diagnostics Function This subtest is for IBM compatible printers, and tests the following functions: Normal print Double-width print Compressed print Emphasized print Double-strike print All characters print This subtest prints the various print types shown below: Subtest 03 Wrap around NOTE: To execute this subtest, a printer wraparound connector must be connected to the printer port in the Port Replicator.
PAGE 132
3 Tests and Diagnostics 3.9 3.9 Async Test Async Test To execute the Async Test, select 7 from the DIAGNOSTIC TEST MENU, press Enter and follow the directions displayed on the screen. The Async test contains two subtests that test the asynchronous communication functions. Move the highlight bar to the subtest you want to execute and press Enter.
PAGE 133
3.9 Async Test Subtest 06 3 Tests and Diagnostics FIR/SIR Point to Point (send) NOTE: To execute subtests 06 and 07, each computer must have access to the other computer’s infrared port. This subtest sends 20h through 7Eh data to the receive side, then receives the sent data and compares it to the original data through the FIR/SIR port. Subtest 07 FIR/SIR Point to Point (receive) This subtest is used with subtest 06 described above.
PAGE 134
3 Tests and Diagnostics 3.10 3.10 Hard Disk Test Hard Disk Test To execute the Hard Disk Test, select 8 from the DIAGNOSTIC TEST MENU, press Enter, and follow the directions on the screen. The hard disk test contains ten subtests that test the hard disk drive functions. NOTE: To execute the subtest 02,03,04,06,09 or 10, the system requires you to enter password. The contents of the hard disk will be erased when the subtest 02, 03, 04, 06,09, or 10 is executed.
PAGE 135
3.10 Hard Disk Test 3 Tests and Diagnostics 3. The Hard Disk Test message will appear after you respond to the Detail Status prompt. Select the number of the subtest you want to execute and press Enter. The following message will appear during each subtest.
PAGE 136
3 Tests and Diagnostics Subtest 04 3.10 Hard Disk Test Cross Talk & Peak Shift This subtest writes eight types of worst pattern data (listed below) to a cylinder, then reads the data while moving from cylinder to cylinder.
PAGE 137
3.11 Real Timer Test 3.11 3 Tests and Diagnostics Real Timer Test To execute the Real Timer Test, select 9 from the DIAGNOSTIC TEST MENU, press Enter and follow the directions on the screen. The real timer test contains three Subtests that test the computer’s real timer functions. Move the highlight bar to the Subtest you want to execute and press Enter. Subtest 01 Real Time A new date and time can be input during this Subtest. To execute the real time subtest follow these steps: 1.
PAGE 138
3 Tests and Diagnostics Subtest 03 3.11 Real Timer Test Real Time Carry CAUTION: When you execute this Subtest, the current date and time are erased. This Subtest checks the real time clock increments, making sure the date and time are displayed in the following format: Current date : Current time : 12-31-1999 23:59:58 PRESS [Enter] KEY TO EXIT TEST Press Enter to exit.
PAGE 139
3.12 NDP Test 3.12 3 Tests and Diagnostics NDP Test To execute the NDP test, select 10 from the DIAGNOSTICS TEST MENU, press Enter and follow the directions on the screen. The NDP test contains one Subtest that tests the computer’s NDP functions. Subtest 01 NDP This test checks the following functions of the coprocessor: Control word Status word Bus Addition Multiplication Press Ctrl + Break to exit.
PAGE 140
3 Tests and Diagnostics 3.13 Expansion Test 3 3.13 Expansion Test To execute the expansion test, select 11 from the DIAGNOSTICS TEST MENU, press Enter and follow the directions on the screen. The expansion test contains two subtests. NOTE: To execute this subtest, the PC card wraparound connector is required.
PAGE 141
3.14 CD-ROM/DVD-ROM Test 3 Tests and Diagnostics 3.14 CD-ROM/DVD-ROM Test To execute the CD-ROM/DVD-ROM test, select 13 from the DIAGNOSTICS TEST MENU, press Enter and follow the directions on the screen. The CD-ROM/DVD-ROM test contains six Subtests that test the computer’s CD-ROM/DVD-ROM functions. Subtest 01 Sequential Read This Subtest is a sequential reading of one-block units (2K bytes) of all the logical addresses.
PAGE 142
3 Tests and Diagnostics 3.15 LAN Test 3.15 LAN Test To execute the LAN test, select 14 from the DIAGNOSTICS TEST MENU, press Enter and follow the directions on the screen. The LAN test contains one Subtest that tests the computer’s LAN function. Subtest 01 MAC Display This Subtest displays the MAC address of the computer’s LAN function.
PAGE 143
3.16 Wireless LAN Test (Agere) 3 Tests and Diagnostics 3.16 Wireless LAN Test (Agere) This section describes how to perform the wireless LAN transmitting-receiving test with the test program. Note: Use another computer (with Agere wireless LAN card) that can communicate by the wireless LAN as a reference machine to perform this test.
PAGE 144
3 Tests and Diagnostics Subtest 01 3.16 Wireless LAN Test (Agere) Transmit & Receive test This sub test checks transmit and receive functions. Transmit test Press 1 to select the test and press Enter in the target machine as a responder. The following message will appear: ############################################################# #### Wireless LAN sub system repair test VX.
PAGE 145
3.16 Wireless LAN Test (Agere) 3 Tests and Diagnostics When the machine has passed the test, “OK” message will appear in the test machine. Then press Enter in the target machine; the “OK” message will appear also in the target machine. Press Enter to return to the main menu. Receive test In receive test reverse the procedures of the transmit test.
PAGE 146
3 Tests and Diagnostics 3.16 Wireless LAN Test (Agere) Press 0 to select the test and press Enter in the target machine. The following message will appear: ############################################################# #### Wireless LAN sub system repair test VX.
PAGE 147
3.16 Wireless LAN Test (Agere) Subtest 02 3 Tests and Diagnostics Mac Address test This subtest reads MAC Address. If there is no problem, the “OK” message will appear. Subtest 03 Wireless LAN (WEP64/128) test This subtest reads the WEP of the wireless LAN card installed in the target machine.
PAGE 148
3 Tests and Diagnostics 3.17 Wireless LAN Test (Atheros) 3.17 Wireless LAN Test (Atheros) This section describes how to perform the wireless LAN transmitting-receiving test with the test program. Note: Use another computer (with Atheros wireless LAN card) that can communicate by the wireless LAN as a responder machine to perform this test. In this test, the following items are tested: * Test PC [Initiator] side (1) SKU (destination code) check (2) Mac Address check (3) Communication test (802.
PAGE 149
3.17 Wireless LAN Test (Atheros) 3 Tests and Diagnostics Setting the responder machine Note: Release the write-protection of the floppy disk for the test. Insert a floppy disk containing the test program into the FDD for the responder machine and turn on the responder machine. The Wireless LAN test menu will appear. ############################################################### #### Atheros WLAN sub system repair test VX.XX #### ############################################################### * * * 1 ..
PAGE 150
3 Tests and Diagnostics 3.17 Wireless LAN Test (Atheros) When the tester machine has passed the test, "OK" message will appear in the tester machine. Press Enter to return to the main menu. When the tester machine has not passed the test, "NG" message will appear in the tester machine. Pressing Enter on the screen shows the following message. ************************************************************* * * * 8.
PAGE 151
3.18 Sound/LAN/Modem Test 3 Tests and Diagnostics 3.18 Sound/LAN/Modem Test This section describes how to perform the Sound/LAN/Modem test with the test program. CAUTION: The system is capable of producing high volume sound. When you use a headphone, be careful to set the volume low and adjust it as necessary. Using a headphone at full volume might damage your ears. Toshiba MS-DOS is required to run the DIAGNOSTICS TEST PROGRAM.
PAGE 152
3 Tests and Diagnostics Subtest 01 3.18 Sound/LAN/Modem Test Microphoned recording & play This subtest checks the function of the CODEC A/D D/A converter. Both the microphone and headphone terminal can be checked at the same time. Before executing this subtest, connect an external microphone to the computer. IF necessary, connect a headphone to the computer to check whether the headphone jack of the computer is working properly. When the subtest is selected, the following message appears. ....
PAGE 153
3.18 Sound/LAN/Modem Test 3 Tests and Diagnostics To execute a subtest continuously, select the test number and press Enter. To exit the Sound/LAN/Modem test, remove the test program disk from the USB FDD and turn the computer off. Subtest 02 Sin Wave This subtest is executed by the load format of COM file (ADSIN.COM). The program expands sin wave data table to data in 16-64KB, and creates play data (It sounds like continuous beep).
PAGE 154
3 Tests and Diagnostics Subtest 03 3.18 Sound/LAN/Modem Test LAN Test (a) Select 3 to execute and press Enter. The following message will appear: COMPLETED Repeat count = 00000 Error count = 00000 XXXX (XXXXX) LAN TEST Vol.X.XX 100Mbps Auto-negotiation TxRx Test Destination Address = xxxxxxxxxxxx Source Address = xxxxxxxxxxxx ** 100Base-TX Full-Duplex ** < TRANSMIT > < RECEIVE > NOTE: The menu displayed by your computer may be slightly different from the one shown above.
PAGE 155
3.18 Sound/LAN/Modem Test Subtest 04 3 Tests and Diagnostics Modem Test (a) Select 4 to execute and press Enter. The following message will appear: ICH MDC Test Program with Modem Sound ( PCB Interface ) Version X.X * Scorpio Modem Initialize :OK * Digital Loopback Test :OK * Modem Sound Test :( Operator’s Check!! ) (b) After a few seconds, the following message will appear: ...Press Key ( Y = OK , N =NG ) If you hear the modem sound from the speakers, press Y. Otherwise, press N.
PAGE 156
3 Tests and Diagnostics 3.19 IEEE1394 Test Program 3.19 IEEE1394 Test Program This section describes how to perform the IEEE1394 test with the test program. Toshiba MS-DOS is required to run the DIAGNOSTICS TEST PROGRAM. To start the DIAGNOSTIC TEST PROGRAM, follow these steps: (a) Insert the Diagnostics disk in the floppy disk drive and turn on the computer. (The Diagnostics Disk contains the MS-DOS boot files.
PAGE 157
3.19 IEEE1394 Test Program Subtest 01 3 Tests and Diagnostics IEEE1394 test This program checks the data transporting between responder machine and target machine. NOTE: Subtest 02 Use another computer that can communicate by IEEE1394 (i. Link) cable as a reference machine to perform this test. Responder tool This program initializes the machine responder. Subtest 03 ID Check This program checks the GUID.
PAGE 158
3 Tests and Diagnostics 3.20 Bluetooth Test 3.20 Bluetooth Test This section describes how to perform the Bluetooth test program to check if the Bluetooth functions of computer are working properly. To start the Bluetooth test program, follow the steps below: NOTE: Use another computer that can communicate by the Bluetooth as a reference machine to perform this test. Insert a floppy disk containing the test program into the target machine and turn on the target machine.
PAGE 159
3.20 Bluetooth Test Subtest 01 3 Tests and Diagnostics BD_ADDR check This subtest checks the BD_ADDR functions. When the Bluetooth test menu is displayed, press 1 to select the test and press Enter. The following message will appear: ----------------------------------------------------------------------------Bluetooth Subsystem T&D for PCSE(BD_ADDR) VerX.XX Copyright (C) by TOSHIBA Co.
PAGE 160
3 Tests and Diagnostics 3.20 Bluetooth Test If the target machine has any problem, it displays Error CODE. The following message is desplayed. ----------------------------------------------------------------------------Bluetooth Subsystem T&D for PCSE(BD_ADDR) VerX.XX Copyright (C) by TOSHIBA Co.
PAGE 161
3.20 Bluetooth Test 3 Tests and Diagnostics If the machine detects a malfunction, it indicates the error code as shown below. The error code begins with the least significant digit. Error code Table 3-2 Error code for Bluetooth test (BD_ADDR) (1/2) Error code 0x01 0x02 0x03 0x04 0x05 0x06 0x07 0x08 0x09 0x0a 0x0b 0x0c 0x0d 0x0e 0x0f 0x10 0x11 0x12 0x13 0x14 0x15 0x16 0x17 0x18 0x19 0x1a 0x1b 0x1c 0x1d 0x1e 0x1f Meaning Unknown HCI Command. No Connection. Hardware Failure. Page Timeout.
PAGE 162
3 Tests and Diagnostics 3.20 Bluetooth Test Table 3-2 Error code for Bluetooth test (BD_ADDR) (2/2) Error code 0x20 0x21 0x22 0x23 0x24 0x25 0x26 0x27 0x28 0x29 0x2a 0x2b 0x2c 0x2d 0x2e 0x2f Meaning Unsupported LMP Parameter Value. Role Change Not Allowed. LMP Response Timeout. LMP Error Transaction Collosion. LMP PDU Not Allowed. Not Exist Not Exist Not Exist Not Exist Not Exist Not Exist Not Exist Not Exist Not Exist Not Exist Not Exist ** See the Specification of the Bluetooth System in detail.
PAGE 163
3.20 Bluetooth Test 3 Tests and Diagnostics When the Bluetooth test menu is displayed, press T to select the test and press Enter in the test machine. The following message will appear: ----------------------------------------------------------------------------Bluetooth Subsystem T&D for PCSE(CS-Air) VerX.XX Copyright (C) by TOSHIBA Co.
PAGE 164
3 Tests and Diagnostics 3.20 Bluetooth Test If the target machine has any problem, the following message “INCOMPLETE” is displayed with the Error CODE. ----------------------------------------------------------------------------Bluetooth Subsystem T&D for PCSE(CS-Air) VerX.XX Copyright (C) by TOSHIBA Co.
PAGE 165
3.20 Bluetooth Test 3 Tests and Diagnostics If the machine detects a malfunction, it indicates the error code as shown below. The error code begins with the least significant digit. Error code Table 3-3 Error code for Bluetooth test (BD_ADDR of the DUT) (1/2) Error code 0x01 0x02 0x03 0x04 0x05 0x06 0x07 0x08 0x09 0x0a 0x0b 0x0c 0x0d 0x0e 0x0f 0x10 0x11 0x12 0x13 0x14 0x15 0x16 0x17 0x18 0x19 0x1a 0x1b 0x1c 0x1d 0x1e 0x1f Meaning Unknown HCI Command. No Connection. Hardware Failure. Page Timeout.
PAGE 166
3 Tests and Diagnostics 3.20 Bluetooth Test Table 3-3 Error code for Bluetooth test (BD_ADDR of the DUT) (2/2) Error code 0x20 0x21 0x22 0x23 0x24 0x25 0x26 0x27 0x28 0x29 0x2a 0x2b 0x2c 0x2d 0x2e 0x2f Meaning Unsupported LMP Parameter Value. Role Change Not Allowed. LMP Response Timeout. LMP Error Transaction Collosion. LMP PDU Not Allowed.
PAGE 167
3.21 Error Code and Error Status Names 3 Tests and Diagnostics 3.21 Error Code and Error Status Names Table 3-4 lists the error codes and error status names for the Diagnostic Test.
PAGE 168
3 Tests and Diagnostics 3.
PAGE 169
3.
PAGE 170
3 Tests and Diagnostics 3.22 Hard Disk Test Detail Status 3.22 Hard Disk Test Detail Status When an error occurs in the hard disk test, the following message is displayed: HDC status = XXXXXXXX Detailed information about the hard disk test error is displayed on the screen by an eight-digit number. The first four digits represent the hard disk controller (HDC) error status number and the last four digits are not used.
PAGE 171
3.22 Hard Disk Test Detail Status 3 Tests and Diagnostics Table 3-6 Error register contents Bit Name Description 7 BBK1 (Bad block mark) “0” … Not used “1” … A bad block mark is detected. 6 UNC (Uncorrectable) “0” … There is no uncorrectable data error. “1” … Uncorrectable data error has been detected. 5 —— Not used 4 IDNF (Identification) “0” … Not used “1” … There was no ID field in the requested sector.
PAGE 172
3 Tests and Diagnostics 3.23 Head Cleaning 3.23 Head Cleaning 3.23.1 Function Description This function cleans the heads in the FDD by executing a series of head load/seek and read operations. A cleaning kit is necessary to perform this program. 3.23.2 Operations 1. Selecting test 4 from the DIAGNOSTIC MENU and pressing Enter displays the following messages: DIAGNOSTICS - FLOPPY DISK HEAD CLEANING : VX.XX Mount cleaning disk(s) on drive(s). Press any key when ready. 2.
PAGE 173
3.24 Log Utilities 3 Tests and Diagnostics 3.24 Log Utilities 3.24.1 Function Description This function logs error information generated while a test is in progress and stores the results in RAM. This function can store data on a floppy disk or output the data to a printer. If the power switch is turned off, the error information will be lost. The error information is displayed in the following order: 1. Error count (CNT) 2. Test name (TS-NAME) 3. Subtest number (TS-NAME) 4. Pass count (PASS) 5.
PAGE 174
3 Tests and Diagnostics 3.24 Log Utilities 2. The error information displayed on the screen can be manipulated by the following number keys: 1 scrolls the display to the next page. 2 scrolls the display to the previous page. 3 returns to the Diagnostic Menu. 4 erases all error log information in RAM. 5 outputs the error log information to a printer. 6 reads the log information from a floppy disk. 7 writes the log information to a floppy disk. 3.
PAGE 175
3.25 Running Test 3 Tests and Diagnostics 3.25 Running Test 3.25.1 Function Description This function automatically executes the following tests in sequence: 1. 2. 3. 4. 5. 6. 7. 8. System test (subtest 01) Memory test (subtests 01, 02, 04, and 06) Real timer test (subtest 02) Display test (subtest 01) FDD test (subtest 02) HDD test (subtests 01 and 05) Printer test (subtest 03) if selected Async test (subtest 01) (not supported in this model) 3.25.
PAGE 176
3 Tests and Diagnostics 3.25 Running Test 4. Select No and press Enter. The following message will appear: Mount the work disk(s) on the drive(s), then press [Enter] key. [Warning : The contents of the disk(s), will be destroyed.] 5. This program is executed continuously. To terminate the program, press Ctrl +Break.
PAGE 177
3.26 Floppy Disk Drive Utilities 3 Tests and Diagnostics 3.26 Floppy Disk Drive Utilities 3.26.1 Function Description This function formats the FDD, copies the floppy disk and displays the dump list for both the FDD and HDD. 1. FORMAT NOTE: This program is only for testing a floppy disk drive. The option is different from the Toshiba MS-DOS FORMAT command. This program can format a 5.25-inch or 3.
PAGE 178
3 Tests and Diagnostics 3.26 Floppy Disk Drive Utilities 3.26.2 Operations 1. Selecting 7 from the DIAGNOSTIC MENU and pressing Enter displays the following message: [ FDD UTILITIES ] 1 2 3 4 9 - FORMAT COPY DUMP HDD ID READ EXIT TO DIAGNOSTICS MENU 2. FORMAT program (a) Selecting FORMAT displays the following message: DIAGNOSTICS - FLOPPY DISK FORMAT : VX.
PAGE 179
3.26 Floppy Disk Drive Utilities 3 Tests and Diagnostics 3. COPY program (a) When COPY is selected, the following message appears: FLOPPY DISK FORMAT & COPY : VX.XX Type select (0:2DD,3:2HD) ? (b) Selecting a media/drive type number will display a message similar to the one below: Insert source disk into drive A: Press any key when ready. (c) Remove the Diagnostics Disk from the FDD, insert the source disk and press any key. The following message will appear, indicating the program has started.
PAGE 180
3 Tests and Diagnostics 3.26 Floppy Disk Drive Utilities 4. DUMP program (a) When DUMP is selected, the following message appears: DIAGNOSTICS-HARD DISK & FLOPPY DISK DUMP : VX.XX Drive type select (1:FDD, 2:HDD) ? (b) When FDD is selected, the following message appears. Select a format type number. When HDD is selected, the display will go to step (g). Select drive number (1:A, 2:B) ? (c) Select a drive number and the following message will be displayed.
PAGE 181
3.26 Floppy Disk Drive Utilities 3 Tests and Diagnostics 5. HDD-ID READ Selecting HDD ID READ displays the following HDD ID configuration: [HDD ID Read (VX.XX)] [Drive #X] ID code (h) = XXXX No. of Cylinders = XXXX XXXX Removable Cylinders = XXXX XXXX No. of Heads = XXXX XXXX Unformat Bytes/Track = XXXX XXXX Unformat Bytes/Sector = XXXX XXXX Sectors/Track = XXXX XXXX Gap Length = XXXX XXXX Sync. Bytes = XXXX XXXX Reserved (h) = XXXX Serial No. = YYY...
PAGE 182
3 Tests and Diagnostics 3.27 System Configuration 3 3.27 System Configuration 3.27.1 Function Description The System Configuration program contains the following configuration information for the computer: 1. Processor Type 2. VGA Controller 3. MS-DOS Version 4. BIOS ROM version (1st ID, 2nd ID) 5. Boot ROM version 6. KBC version 7. PS Microprocessor Version 8. Total Memory Size 9. Battery code 10. Sound System 11. The number of printer ports 12. The number of ASYNC ports 13.
PAGE 183
3.27 System Configuration 3.27.2 3 Tests and Diagnostics Operations Selecting 8 from the DIAGNOSTIC MENU and pressing Enter displays the following system configuration: System Configuration Display : Ver x.xx [Machine Name : ] -------------------------------------------------------------------------------* - ProcessorType = xx - xxxxx (?? Step) **- VGA Controller = xxxxxx * - MS-DOS Version = Vx.xx * - BIOS-ROM Version = vx.xx 1st ID = xxH, 2nd ID = xxH * - BOOT-ROM Version = vx.xx * - KBC Version = Vx.
PAGE 184
3 Tests and Diagnostics 3.28 SETUP 3.28.1 Function Description 3.28 SETUP This program displays the current system setup information as listed below: 1. Memory (a) Total 2. System Date/Time (a) Date (b) Time 3. Battery (a) Battery Save Mode 4. Password 5. HDD Password (a) HDD (b) HDD Password Mode (c) User Password 6. Boot Priority (a) Boot Priority (b) HDD Priority (c) Network Boot Protocol 7. Display (a) Power On Display (b) LCD Display Stretch (c) TV Type 8.
PAGE 185
3.28 SETUP 3 Tests and Diagnostics 11. Drives I/O (a) Built-in HDD (b) Select Bay 12. PCI Bus (a) PCI Bus 13. PC Card (a) Controller Mode 14. Peripheral (a) Internal Pointing Device (b) Parallel Port Mode (c) Hard Disk Mode 15. Legacy Emulation (a) USB keyboard/Mouse Legacy Emulation (b) USB-FDD Legacy Emulation 16.
PAGE 186
3 Tests and Diagnostics 3.28.2 3.28 SETUP Accessing the SETUP Program Selecting 0 from the DIAGNOSTICS MENU and pressing Enter displays the TSETUP screen. The TSETUP screen is divided into two pages: SYSTEM SETUP (1/2) and SYSTEM SETUP (2/2). SYSTEM SETUP (1/2) ACPI BIOS version - x.
PAGE 187
3.28 SETUP 3 Tests and Diagnostics SYSTEM SETUP (2/2) CONFIGURATION Device Config. = Setup by OS Serial Parallel I/O PORTS = COM1(3F8H/IRQ4) = LPT1(378H/IRQ7/CH3) DRIVES I/O Built-in HDD = Primary IDE(1F0H/IRQ14) Select Bay = Secondary IDE(170H/IRQ15) PCI BUS PCI BUS = IRQ10, IRQ11 ACPI BIOS version - x.
PAGE 188
3 Tests and Diagnostics 3.28 SETUP Moving Within the SETUP Menu and Changing Values 1. Press Å and Æ to move between the two columns. Press PgDn and PgUp to move between the two pages. Press ↑ and ↓ to move between items in a column. 2. Press either the space bar to change the value. Accepting Changes and Exiting the SETUP Window 1. Press End to accept the changes you made. The following message is displayed: Are you sure? (Y/N) The changes you made will cause the system to reboot. 2.
PAGE 189
3.28 SETUP 3 Tests and Diagnostics SETUP Options The SETUP screen is divided into functionally related groups. This section describes each group and its options. 1. Memory This group of options displays the computer’s memory. (a) Total This field displays the total amount of memory installed and is automatically calculated by the computer. You cannot change this value. 2. System Date/Time Use this option to set the computer’s system date/time.
PAGE 190
3 Tests and Diagnostics 3.28 SETUP Display Auto Off Use this option to disable or set the duration of the display automatic power off function. This function causes the computer to turn the LCD panel’s illumination off if you make no entry for the set period of time. Disabled Disables display automatic power off. xx Min. Automatically turns off power to the LCD panel’s illumination if the panel is not used for the duration set. The duration xx can be set to 1, 3, 5, 10, 15, 20 or 30 minutes.
PAGE 191
3.28 SETUP 3 Tests and Diagnostics 4. Password This option allows you to set or reset the user password for power on. Not Registered Change or remove the password. (Default) For details on setting the user password refer to the User’s Manual. 5. HDD Password This group of options displays the HDD password. You cannot change these values. (a) HDD (b) HDD Password Mode (c) User Password 6.
PAGE 192
3 Tests and Diagnostics 3.28 SETUP (b) HDD Priority This option enables to select the priority for the Built-in HDD, optional second HDD or PC card. Built-in HDD → Second HDD → PC Card (Default) Second HDD → Built-in HDD → PC Card Built-in HDD → PC Card → Second HDD Second HDD → PC Card → Built-in HDD PC Card → Built-in HDD → Second HDD PC Card → Second HDD → Built-in HDD (c) Network Boot Protocol Use this option to set the starting method via a network.
PAGE 193
3.28 SETUP 3 Tests and Diagnostics (c) TV Type This option lets you make settings for television display. NTSC(US) (Default) NTSC(JAPAN) PAL 8. Others Whether or not you need to configure the computer with these options depends primarily on the kind of software or peripherals you use. (a) Power-up Modes Use this option to choose between resume and boot mode. This option can also be set by hotkeys. Boot Turns on boot mode. (Default) Resume Turns on resume mode.
PAGE 194
3 Tests and Diagnostics 3.28 SETUP (c) Level 2 Cache Use this option to enable or disable the level 2 cache. Enabled Enables the level 2 cache. (Default) Disabled Disables the level 2 cache. (d) Dynamic CPU Frequency Mode Use this option to choose from the following settings: Dynamically Switchable Enables the dynamic CPU frequency change function. Always High Disables the dynamic CPU frequency change function and always runs the processor at its maximum speed.
PAGE 195
3.28 SETUP 3 Tests and Diagnostics (f) Panel Power On/Off This option lets you set the Panel Power On/Off function. It is effective only in Resume mode. Enabled Enables the Panel Power On/Off. Disabled Disables the Panel Power On/Off (Default) 9. Configuration This field displays the configuration method. The devices are initialized when the PNP OS loads. Setup by OS First, devices necessary for loading the OS will be initialized. After the PNP OS loads, other devices will be initialized by the OS.
PAGE 196
3 Tests and Diagnostics COM level 3.28 SETUP Interrupt level I/O address COM1 4 3F8H COM2 3 2F8H COM3 4 3E8H COM3 5 3E8H COM3 7 3E8H COM4 3 2E8H COM4 5 2E8H COM4 7 2E8H Not Used (Serial port default) Disables port (b) Parallel This option sets the interrupt request level (IRQ) and I/O port base address for the parallel port. When the Printer Port Mode is set to Std.
PAGE 197
3.28 SETUP 3 Tests and Diagnostics OPTIONS DMA = Channel 3 (Default) For most printers, the port should be set to ECP. With some other parallel devices, the setting should be Std. Bi-Direct. 11. Drives I/O This option displays the address and interrupt level for hard disk drive, CD/DVDROM drive and PC card. It is for information only and cannot be changed. (a) Built-in HDD Primary IDE (1F0H/IRQ14) The Built-in HDD is ready for use. No Drive The Built-in HDD is not installed.
PAGE 198
3 Tests and Diagnostics 3.28 SETUP 14. Peripheral Use this option to select the parallel port mode and hard disk mode. (a) Internal Pointing Device This option enables and disables the Touch Pad and accupoint. Enabled Enables the Touch Pad and accupoint. (Default) Disabled Disables the Touch Pad and accupoint. (b) Ext Keyboard "Fn" Use this option to set the Fn key equivalent when you are using an external keyboard. Selecting this option displays the following subwindow. Enabled Enables the feature.
PAGE 199
3.28 SETUP 3 Tests and Diagnostics (c) Parallel Port Mode The options in this tab are ECP and Standard Bi-directional. ECP Sets the port mode to Extended Capabilities Port (ECP). For most printers, the port should be set to ECP. (Default) Std. Bi-Direct. This setting should be used with some other parallel devices. (d) Hard Disk Mode Use this item to select the hard disk mode. Enhanced IDE (Normal) Standard IDE Select this mode when using an operating system that supports Enhanced IDE.
PAGE 200
3 Tests and Diagnostics 3.28 SETUP 16. PCI LAN This option enables/disables the Built-in LAN functions. (a) Built-in LAN 3-94 Enabled Enables Built-in LAN functions. (Default) Disabled Disables Built-in LAN functions.
PAGE 201
Chapter 4 Replacement Procedures
PAGE 202
4 Replacement Procedures 4-ii Satellite Pro M10 Series Maintenance Manual (960-431)
PAGE 203
4 Replacement Procedures Chapter 4 4.1 Contents General....................................................................................................................... 4-1 Safety Precautions................................................................................................ 4-2 Before You Begin ................................................................................................ 4-3 Disassembly Procedures ......................................................................
PAGE 204
4 Replacement Procedures 4.7 Keyboard.................................................................................................................. 4-29 Removing the Keyboard .................................................................................... 4-29 Installing the Keyboard...................................................................................... 4-33 4.8 Switch Board............................................................................................................
PAGE 205
4 Replacement Procedures Installing the Cooling Fan.................................................................................. 4-56 4.18 RTC Battery ............................................................................................................. 4-57 Removing the RTC Battery ............................................................................... 4-58 Installing the RTC Battery................................................................................. 4-58 4.
PAGE 206
4 Replacement Procedures Removing the TFT FL (Model 14.1 XGA LG. Philips LP141X7-C1TO) ........ 4-90 Installing the TFT FL (Model 14.1 XGA LG. Philips LP141X7-C1TO).......... 4-96 4.29 TFT FL (Model 15.0 XGA Samsung LTN150X6-L01) ........................................ 4-102 Removing the TFT FL (Model 15.0 XGA Samsung LTN150X6-L01) .......... 4-102 Installing the TFT FL (Model 15.0 XGA Samsung LTN150X6-L01)............ 4-110 4.30 TFT FL (Model 15.0 XGA LG. Philips LP150X06 A2) ..........................
PAGE 207
4 Replacement Procedures Figures Figure 4-1 Removing the battery..................................................................................... 4-8 Figure 4-2 Removing a PC Card ................................................................................... 4-10 Figure 4-3 Removing an SD card .................................................................................. 4-11 Figure 4-4 Removing the memory slot cover ................................................................
PAGE 208
4 Replacement Procedures Figure 4-31 Removing the wireless LAN card................................................................ 4-47 Figure 4-32 Removing the screws from the bottom of the computer.............................. 4-49 Figure 4-33 Disconnecting the cable ............................................................................... 4-50 Figure 4-34 Removing the screws from the top cover ....................................................
PAGE 209
4 Replacement Procedures Figure 4-63 Disconnecting the FL tube ground wire ...................................................... 4-87 Figure 4-64 Removing the FL tube ................................................................................. 4-88 Figure 4-65 Removing the outside tape/cover tape ......................................................... 4-91 Figure 4-66 Removing the control PCB, top case and cover assembly ..........................
PAGE 210
4 Replacement Procedures Figure 4-92 Removing the frame................................................................................... 4-121 Figure 4-93 Removing the panel ................................................................................... 4-122 Figure 4-94 Removing the sheets .................................................................................. 4-123 Figure 4-95 Removing the FL .......................................................................................
PAGE 211
4 Replacement Procedures Figure 4-124 Applying the protective cover-G ............................................................... 4-151 Figure 4-125 Applying the protective cover-S ................................................................ 4-152 Figure 4-126 Applying the tapes ..................................................................................... 4-153 Figure 4-127 Removing the covers and tapes .................................................................
PAGE 212
4 Replacement Procedures 4-xii Satellite Pro M10 Series Maintenance Manual (960-431)
PAGE 213
4.1 General 4 4 Replacement Procedures p 4.1 General This section explains how to disassemble the computer and replace Field Replaceable Units (FRUs). It may not be necessary to remove all the FRUs in order to replace one. The chart below is a guide to which FRUs need to be removed in order to remove others.
PAGE 214
4 Replacement Procedures 4.1 General Safety Precautions Before you begin disassembly, read the following safety precautions and observe them carefully as you work. DANGER: 1. Always use the genuine battery that is authorized by TOSHIBA or compatible with the unit. Since other battery packs have different specifications, they may be incompatible with the unit, and may burst or explode. Never heat or disassemble the battery pack, as that could cause leakage of alkaline solution.
PAGE 215
4.1 General 4 Replacement Procedures Before You Begin Look over the procedures in this section before you begin disassembling the computer. Familiarize yourself with the disassembly and reassembly steps. Begin each procedure by removing the AC adapter and the battery pack as instructed in this section: 1. Do not disassemble the computer unless it is operating abnormally. 2. Use only the correct and approved tools. 3.
PAGE 216
4 Replacement Procedures 4.1 General Disassembly Procedures The computer has three basic types of cable connectors: Pressure Plate Connectors Coaxial Cable Connectors Normal Pin Connectors To disconnect a Pressure Plate connector, lift up the tabs on either side of the connector’s plastic pressure plate and slide the cable out of the connector. To connect the cable to a Pressure Plate connector, make sure the pressure plate is fully lifted and slide the cable into the connector.
PAGE 217
4.1 General 4 Replacement Procedures Tools and Equipment The use of Electrostatic Discharge (ESD) equipment is very important for your safety and the safety of those around you. Proper use of these devices will increase the success rate of your repairs and lower the cost for damaged or destroyed parts. The following equipment is necessary to disassemble and reassemble the computer: One M2 point size 0 Phillips screwdriver to remove and replace screws. One 4 mm flat-blade screwdriver.
PAGE 218
4 Replacement Procedures 4.1 General Screw Tightening Torque When you fasten screws, be sure to follow the torque list below. CAUTION: Overtightening can damage components and screws; undertightening can result in electrical shorts or other damage if screws or components come loose. NOTE: TOSHIBA recommends that you use an electric screw driver for quick and easy operations. M2 0.17 N·m (1.7 kgf·cm) M2.5 0.30 N·m (3.0 kgf·cm) M3 0.57 N·m (5.6 kgf·cm) M2.5×4 PSP TITE 0.204 N·m (2.0 kgf·cm) M2.
PAGE 219
4.1 General 4 Replacement Procedures Color of Screw Shaft To avoid mistakes on the screw length, screw shafts are colored as follows: ❑ Even number length screw: brown ❑ Odd number length screw: white ❑ Special length screw: blue Screws whose lengths are indicated to one or more decimal places such as 2.5 mm or 2.8 mm.
PAGE 220
4 Replacement Procedures 4.1 General Removing the Battery Pack To remove the battery pack, follow the steps below and refer to Figure 4-1. CAUTION: When handling battery packs, be careful not to short circuit the terminals. Also do not drop, hit or otherwise apply impact; do not scratch or break the casing and do not twist or bend the battery pack. 1. Turn the computer upside down. 2. Slide the battery latch toward the front to release it, then rotate the battery pack from the right and lift it out.
PAGE 221
4.1 General 4 Replacement Procedures Installing the Battery Pack To install the battery pack, follow the steps below and refer to Figure 4-1. CAUTION: The battery pack is a lithium ion battery, which can explode if not properly replaced, used, handled or disposed of. Dispose of the battery as required by local ordinances or regulations. Use only batteries recommended by TOSHIBA as replacements. NOTE: Check the battery's terminals visually. If they are dirty, wipe them clean with a dry cloth. 1.
PAGE 222
4 Replacement Procedures 4.1 General Removing an Optional PC Card To remove a PC Card (option), follow the steps below and refer to Figure 4-2. CAUTION: Before you remove a PC Card, refer to the card's documentation and to your operating system documentation for proper procedures and precautions. 1. Turn the computer right side up. 2. Press the eject button for the PC Card you want to remove to extend the button. 3. Press the extended eject button to pop the PC Card out slightly. 4.
PAGE 223
4.1 General 4 Replacement Procedures Removing an Optional SD Card To remove an SD card (option), follow the steps below and refer to Figure 4-3. CAUTION: Before you remove an SD card, refer to the card's documentation and to your operating system documentation for proper procedures and precautions. 1. Turn the computer right side up. 2. Push the SD card in and release it to pop the card out slightly. 3. Grasp the SD card and pull it out.
PAGE 224
4 Replacement Procedures 4.2 4.2 Memory Modules Memory Modules Removing a Memory Module To remove a memory module make sure the computer is in boot mode and powered off, follow the steps below and refer to Figures 4-4 and 4-5. CAUTION: Do not try to remove a memory module with the computer turned on. You can damage the computer and the memory. 1. Turn the computer upside down. 2. Remove two M2×4 black flat-head screws from the memory slot cover. 3. Lift off the memory slot cover.
PAGE 225
4.2 Memory Modules 4 Replacement Procedures 4. Gently press out on two latches. One end of the memory module will pop up. 5. Grasp the memory module and pull it out.
PAGE 226
4 Replacement Procedures 4.2 Memory Modules Installing a Memory Module To install a memory module, make sure that the computer is in boot mode and powered off, follow the steps below and refer to Figures 4-4 and 4-5. CAUTION: Do not touch the connectors on the memory module or on the computer. Debris on the connectors may cause memory access problems. 1. Fit the memory module’s connectors into the computer’s connectors and press carefully to ensure firm contact. 2.
PAGE 227
4.3 HDD 4.3 4 Replacement Procedures HDD CAUTION: When handling the HDD, do not press the top surface as shown by the arrow. Hold it by the sides. Removing the HDD To remove the HDD, follow the steps below and refer to Figures 4-6 to 4-8. 1. Turn the computer upside down. 2. Remove two M2.5×12 black flat-head screws securing the HDD cover. 3. Lift off the HDD cover. M2.
PAGE 228
4 Replacement Procedures 4.3 HDD 4. Pull the HDD gently out of the slot. HDD Figure 4-7 Removing the HDD pack NOTE: The following steps describe how to disassemble the HDD pack; however, do not disassemble if the HDD is working properly.
PAGE 229
4.3 HDD 4 Replacement Procedures 5. Place the HDD pack on a flat surface, and remove four M3×4 silver flat-head screws. 6. Remove the HDD bracket. M3×4 silver flat-head screws HDD M3×4 silver flat-head screws HDD bracket Figure 4-8 Removing screws and HDD bracket CAUTION: Do not apply pressure to the top or bottom of the HDD.
PAGE 230
4 Replacement Procedures 4.3 HDD Installing the HDD To install the HDD, follow the steps below and refer to Figures 4-6 to 4-8. CAUTION: Don't hold the HDD by its top and bottom flat surfaces. It may damage the HDD. 1. Seat the HDD in the bracket. 2. Secure the bracket with four M3×4 silver flat-head screws. CAUTION: Do not apply pressure to the middle of the HDD pack. It may damage the HDD bracket. Hold the HDD by its corners. 3. Hold the HDD pack by its corners and insert it into the computer.
PAGE 231
4.4 Slim Select Bay Module 4.4 4 Replacement Procedures Slim Select Bay Module Removing the Slim Select Bay Module To remove the slim select bay module, follow the steps below and refer to Figures 4-9 and 410. 1. If a screw (M3×4 black flat-head screw) is set in the lock position, remove it. 2. Slide the latch toward the back of the computer to release it, and then pull the module out of the slim select bay.
PAGE 232
4 Replacement Procedures 4.4 Slim Select Bay Module NOTE: If you are going to replace an ODD, follow the steps below to disassemble the slim select bay module. 3. Remove two M2×8 black screws securing the connector cover. 4. Remove the connector cover and ODD interface board. 5. Remove five M2×3 thin silver flat-head screws securing the ODD bracket. 6. Remove the ODD bracket.
PAGE 233
4.4 Slim Select Bay Module 4 Replacement Procedures Installing the Slim Select Bay Module To install the slim select bay module, follow the steps below and refer to Figures 4-9 and 410. 1. Seat the ODD in the ODD bracket. 2. Secure the ODD bracket to the ODD with five M2×3 thin silver flat-head screws. 3. Connect the ODD interface board to the ODD. 4. Seat the connector cover and secure it to the ODD with two M2×8 black screws. 5.
PAGE 234
4 Replacement Procedures 4.5 4.5 Modem Daughter Card Modem Daughter Card Removing the Modem Daughter Card To remove the modem daughter card (MDC), follow the steps below and refer to Figures 411 and 4-12. 1. Remove one M2.5×6 black flat-head screw and two M2.5×4 black flat-head screws securing the CPU/MDC slot cover. 2. Remove the CPU/MDC slot cover. M2.5×4 black flat-head screws M2.
PAGE 235
4.5 Modem Daughter Card 4 Replacement Procedures 3. Remove two M2×4 screws securing the MDC. 4. Carefully lift up the MDC to disconnect it from PJ2017 on the system board. 5. Carefully disconnect the modem cable from JP1 on the MDC.
PAGE 236
4 Replacement Procedures 4.5 Modem Daughter Card Installing the Modem Daughter Card To install the modem daughter card (MDC), follow the steps below and refer to Figures 4-11 and 4-12. 1. Carefully connect the modem cable to JP1 on the MDC. 2. Seat the MDC and press carefully on the right end of the card to connect it to PJ2017 on the system board. Be careful not to damage the card or connector. 3. Secure the MDC with two M2×4 screws. 4. Seat the CPU/MDC slot cover. 5. Secure the cover with one M2.
PAGE 237
4.6 CPU 4.6 4 Replacement Procedures CPU Removing the CPU To remove the CPU, follow the steps below and refer to Figures 4-13 and 4-16. 1. Remove one M2.5×6 black flat-head screw and two M2.5×4 black flat-head screw securing the CPU/MDC slot cover, if necessary. 2. Remove two M2×4 black screws securing the metal brace to remove it.
PAGE 238
4 Replacement Procedures 4.6 CPU 3. Remove the cooling module. Cooling module Figure 4-14 Removing the cooling module 4. Turn the cam to the unlock position with a flat-blade screwdriver to unlock the CPU.
PAGE 239
4.6 CPU 4 Replacement Procedures 5. Lift up the CPU.
PAGE 240
4 Replacement Procedures 4.6 CPU Installing the CPU To install the CPU, follow the steps below and refer to Figures 4-13 to 4-17. 1. Make sure the cam is in the open position. 2. Seat the CPU in the CPU socket, aligning the triangle mark on the CPU with that on the socket. Make sure the alignment is exact to avoid damaging pins on the CPU. 3. Press the interposer gently with your fingers and turn the cam on the CPU socket to the lock position with a flat-blade screwdriver to secure the CPU. 4.
PAGE 241
4.7 Keyboard 4.7 4 Replacement Procedures Keyboard Removing the Keyboard To remove the keyboard, follow the steps below and refer to Figures 4-18 to 4-21. 1. Open the display panel. 2. Insert your fingernails into notches in the keyboard brace and the computer, and pry up to unlatch the brace at twelve points and remove it.
PAGE 242
4 Replacement Procedures 4.7 Keyboard 3. Remove two M2.5×2.6 black flat-head screws securing the keyboard. 4. Rotate out the keyboard and lay it on top of the palm rest. M2.5×2.
PAGE 243
4.7 Keyboard 4 Replacement Procedures 5. Remove one M2.5×16 black screw securing the metal plate to remove it. M2.
PAGE 244
4 Replacement Procedures 4.7 Keyboard 6. Disconnect the keyboard cable from PJ123 on the system board, and remove the keyboard.
PAGE 245
4.7 Keyboard 4 Replacement Procedures Installing the Keyboard To install the keyboard, follow the steps below and refer to Figures 4-18 to 4-21. 1. Lay the keyboard on the palm rest upside down. 2. Connect the keyboard cable to PJ123 on the system board. 3. Seat the metal plate and secure it with one M2.5×16 black screw. 4. Turn the keyboard right side up and seat it. 5. Secure the keyboard with two M2.5×3 black flat-head screws. 6. Seat the keyboard brace and press to secure twelve latches.
PAGE 246
4 Replacement Procedures 4.8 4.8 Switch Board Switch Board Removing the Switch Board To remove the switch board, make sure the computer is in boot mode and powered off, follow the steps below and refer to Figure 4-22. 1. Disconnect the switch board cable from PJ2025 on the system board. 2. Remove two M2.5×3 black flat-head screws. 3. Remove the switch board. M2.
PAGE 247
4.8 Switch Board 4 Replacement Procedures Installing the Switch Board To install the switch board, make sure that the computer is in boot mode and powered off, follow the steps below and refer to Figure 4-22. 1. Seat the switch board. 2. Secure the switch board with two M2.5×3 black flat-head screws. 3. Connect the switch board cable to PJ2025 on the system board. Route the switch board cable under the speaker cables.
PAGE 248
4 Replacement Procedures 4.9 4.9 Speakers Speakers Removing the Speakers To remove the speakers, follow the steps below and refer to Figures 4-23 and 4-24. 1. Turn the computer upside down. 2. Remove two M2.5×16 black screws. M2.
PAGE 249
4.9 Speakers 4 Replacement Procedures 3. Remove one M2.5×4 black flat-head screw securing each speaker. 4. Disconnect two speaker cables from PJ5004 and PJ5005 on the system board. 5. Free two speaker cables from their hooks. 6. Remove one M2.5×4 black flat-head screw from each of the speaker. 7. Remove the speakers. M2.
PAGE 250
4 Replacement Procedures 4.9 Speakers Installing the Speakers To install the speakers, follow the steps below and refer to Figures 4-23 and 4-24. 1. Seat each of the speaker and secure it from one latch. 2. Secure each of the speaker with one M2.5×4 black flat-head screw. 3. Route two speaker cables through their hooks. 4. Connect the right speaker cable (red) to PJ5004 on the system board. 5. Connect the left speaker cable (blue) to PJ5005 on the system board. 6.
PAGE 251
4.10 Palm Rest 4 Replacement Procedures 4.10 Palm Rest Removing the Palm Rest To remove the palm rest, follow the steps below and refer to Figures 4-25 and 4-26. 1. Turn the computer upside down. 2. Remove seven M2.5×12 black screws. M2.5×12 black screws M2.
PAGE 252
4 Replacement Procedures 4.10 Palm Rest 3. Turn the computer right side up and open the display panel. 4. Disconnect the pad cable from PJ2003 on the system board. 5. Remove two M2.5×5 black flat-head screws securing the palm rest. 6. Release two latches to remove the palm rest. M2.
PAGE 253
4.10 Palm Rest 4 Replacement Procedures Installing the Palm Rest To install the palm rest, follow the steps below and refer to Figures 4-25 and 4-26. 1. Insert four tabs of the palm rest into the slits on the top cover to seat the palm rest. Secure the palm rest with two latches. 2. Secure the palm rest with two M2.5×5 black flat-head screws 3. Connect the pad cable to PJ2003 on the system board. 4. Close the display panel and turn the computer upside down. 5. Secure seven M2.5×12 black screws.
PAGE 254
4 Replacement Procedures 4.11 Touch Pad 4.11 Touch Pad Removing the Touch Pad To remove the touch pad, follow the steps below and refer to Figures 4-27 and 4-28. 1. Remove two M2.5×5 black flat-head screws and two M2.5×4 screws from the back of the palm rest. M2.5×4 screws Palm rest M2.
PAGE 255
4.11 Touch Pad 4 Replacement Procedures 2. Hold the palm rest with both hands and then slightly bend it to release two latches securing each sides of the touch pad cover. Be careful not to bend the palm rest excessively, or it will be broken. 3. Remove the touch pad cover and touch pad. 4. Disconnect the pad cable from the connector on the touch pad.
PAGE 256
4 Replacement Procedures 4.12 Internal Microphone 4.12 Internal Microphone Removing the Internal Microphone To remove the internal microphone, follow the steps below and refer to Figure 4-29. 1. Remove one strip of tape securing the internal microphone cable. 2. Disconnect the internal microphone cable from PJ5002 on the sound board. 3. Remove the internal microphone.
PAGE 257
4.13 Bluetooth Module 4 Replacement Procedures 4.13 Bluetooth Module Removing the Bluetooth Module To remove the Bluetooth module, follow the steps below and refer to Figure 4-30. NOTE: The Bluetooth module is an option in some models. 1. Disconnect the Bluetooth antenna coaxial cable (brown) from module's connector using an antenna coaxial cable disconnector. 2. Turn up the insulator. 3. Disconnect the Bluetooth module cable from PJ4900 on the system board. 4.
PAGE 258
4 Replacement Procedures 4.13 Bluetooth Module Installing the Bluetooth Module To install the Bluetooth module, make sure that the computer is in boot mode and powered off, follow the steps below and refer to Figure 4-30. NOTE: The Bluetooth module is an option in some models. 1. Connect the Bluetooth module cable to the connector on the Bluetooth module. 2. Seat the Bluetooth module and secure it with two M2×4 screws. 3. Connect the Bluetooth module cable to PJ4900 on the system board. 4.
PAGE 259
4.14 Wireless LAN Mini PCI Card 4 4 Replacement Procedures s 4.14 Wireless LAN Mini PCI Card Removing the Wireless LAN Mini PCI Card To remove the wireless LAN Mini PCI card, make sure the computer is in boot mode and powered off, follow the steps below and refer to Figure 4-31. 1. Remove one strip of tape securing the antenna coaxial cables. 2. Disconnect two antenna coaxial cables from the wireless LAN Mini PCI card using an antenna coaxial cable disconnector. 3. Gently press out on the latches.
PAGE 260
4 Replacement Procedures 4.14 Wireless LAN Mini PCI Card Installing the Wireless LAN Mini PCI Card To install the wireless LAN Mini PCI card, follow the steps below and refer to Figure 4-31. 1. Fit the wireless LAN Mini PCI card’s connector into the computer’s connectors and press it carefully to ensure firm contact. CAUTION: Do not touch the connectors on the wireless LAN Mini PCI card or on the computer. Debris on the connectors may cause the card to malfunction or to get damaged. 2.
PAGE 261
4.15 Top Cover with Display Assembly 4 Replacement Procedures 4.15 Top Cover with Display Assembly Removing the Top Cover with Display Assembly To remove the top cover with display assembly, follow the steps below and refer to Figures 4-32 to 4-35. 1. Turn the computer upside down. 2. Remove one M2.5×6 black flat-head screw and two M2.5×4 black flat-head screw securing the CPU/MDC slot cover to remove it, if necessary. 3. Remove the following five screws: • Two M2.5×16 black flat-head screws • Three M2.
PAGE 262
4 Replacement Procedures 4.15 Top Cover with Display Assembly 4. Turn the computer right side up and open the display panel. 5.
PAGE 263
4.15 Top Cover with Display Assembly 4 Replacement Procedures 6. Remove following screws from the top cover: • Three M2.5×5 black screws • One M2.5×4 brass flat-head screw • One M2.5×12 black flat-head screw M2.5×5 black screws M2.5×12 black flat-head screw M2.
PAGE 264
4 Replacement Procedures 4.15 Top Cover with Display Assembly 7. Lift up the display assembly to release six latches securing the top cover with the bottom case, and then remove the top cover and display assembly.
PAGE 265
4.15 Top Cover with Display Assembly 4 Replacement Procedures Installing the Top Cover with Display Assembly To install the top cover with display assembly, follow the steps below and refer to Figures 432 to 4-35. 1. Seat the top cover with display assembly and secure it with six latches. 2. Secure the top cover with following screws: • Three M2.5×5 black screws • One M2.5×4 brass flat-head screw • One M2.5×12 black flat-head screw 3.
PAGE 266
4 Replacement Procedures 4.16 Sound Board 4.16 Sound Board Removing the Sound Board To remove the sound board, follow the steps below and refer to Figure 4-36. 1. Remove two M2.5×4 screws securing the sound board. 2. Gently lift up the sound board to disconnect it from PJ5006 on the system board. Sound board's connector PJ5006 Sound board M2.5×4 screws Figure 4-36 Removing the sound board Installing the Sound Board To install the sound board, follow the steps below and refer to Figure 4-36. 1.
PAGE 267
4.17 Cooling Fan 4 Replacement Procedures 4.17 Cooling Fan Removing the Cooling Fan To remove the cooling fan, follow the steps below and refer to Figures 4-37. CAUTION: The cooling fan can become very hot during operation. Wait for the fan to cool before removing it. Do not touch the fan rotor or fan blades or apply impact to the cooling fan module. 1. Remove one strip of tape securing the cooling fan cable. 2. Remove the cooling fan cable from PJ8770 on the system board. 3. Remove two M2.
PAGE 268
4 Replacement Procedures 4.17 Cooling Fan Installing the Cooling Fan To install the cooling fan, follow the steps below and refer to Figures 4-37. CAUTION: When you remove the cooling fan, wipe the grease off of the bottom of the heat sink and top of the CPU. Apply new grease. 1. Seat the cooling fan and secure it with two M2.5×6 black flat-head screws. 2. Connect the cooling fan cable to PJ8770 on the system board. 3. Secure the cooling fan cable with one strip of tape.
PAGE 269
4.18 RTC Battery 4 Replacement Procedures 4.18 RTC Battery WARNING: When it is necessary to replace the RTC battery, be sure to use genuine batteries or replacement batteries authorized by TOSHIBA. Installing the wrong battery could cause a battery explosion or other damage. If the RTC battery is found abnormal, it must not be installed. Replace it with a new battery, and dispose of the old one according to the local regulations.
PAGE 270
4 Replacement Procedures 4.18 RTC Battery Removing the RTC Battery To remove the RTC battery, follow the steps below and refer to Figure 4-38. 1. Remove two strips of tape securing the RTC battery cable. 2. Disconnect the RTC battery cable from PJ9999 on the system board. 3. Remove one strip of tape securing the RTC battery. 4. Lift out the RTC battery.
PAGE 271
4.19 System Board 4 Replacement Procedures 4.19 System Board Removing the System Board To remove the system board, follow the steps below and refer to Figures 4-39 to 4-41. 1. Lift the AC adaptor jack out of its slot.
PAGE 272
4 Replacement Procedures 4.19 System Board 2. Rotate the system board from the right side to lift it out of the bottom case. Be careful not to catch the bottom case on the eject buttons of the PC Card Slot. 3. Disconnect the AC adaptor jack from PJ8800 on the system board.
PAGE 273
4.19 System Board 4 Replacement Procedures 4. Remove two strips of tape securing the modem cable. 5. Disconnect the modem cable from PJ2018 on the system board. PJ2018 Modem cable Tapes Figure 4-41 Removing the modem cable Installing the System Board To install the system board, follow the steps below and refer to Figures 4-39 to 4-41. 1. Connect the modem cable to PJ2018 on the system board. 2. Secure the modem cable with two strips of tape. 3. Connect AC adaptor jack to PJ8800 on the system board.
PAGE 274
4 Replacement Procedures 4.20 VGA Board 4.20 VGA Board Removing the VGA Board To remove the VGA board, follow the steps below and refer to Figure 4-42. 1. Remove three M2×4 screws securing the VGA board. 2. Gently lift up the VGA board to disconnect it from PJ100 on the system board. M2×4 screws VGA board's connector PJ100 VGA board Figure 4-42 Removing the VGA board Installing the VGA Board To install the VGA board, follow the steps below and refer to Figure 4-42. 1.
PAGE 275
4.21 USB Board 4 Replacement Procedures 4.21 USB Board Removing the USB Board To remove the USB board, follow the steps below and refer to Figure 4-43. 1. Remove one M2×4 screw securing the USB board. 2. Remove the USB board. M2×4 screw USB board Figure 4-43 Removing the USB board Installing the USB Board To install the USB board, follow the steps below and refer to Figure 4-43. 1. Seat the USB board and secure it with one M2×4 screw.
PAGE 276
4 Replacement Procedures 4 4.22 Display Mask s 4.22 Display Mask Removing the Display Mask To remove the display mask, follow the steps below and refer to Figures 4-44 and 4-45. 1. Remove two mask seals at the bottom corners of the display assembly. 2. Remove two M2.5×6 black flat-head screws securing the display mask. NOTE: Support the display with your hand when you remove the screws. Mask seals M2.
PAGE 277
4.22 Display Mask 4 Replacement Procedures 3. Release the twenty-seven latches on the display mask in the following order: • Seven latches on the bottom • six latches each on the right and left sides • eight latches on the top.
PAGE 278
4 Replacement Procedures 4.22 Display Mask Installing the Display Mask To install the display mask, follow the steps below and refer to Figures 4-44 and 4-45. 1. Place the display mask in position, and fasten the twenty-seven latches in the following order: • Eight latches on the top • Six latches each on the right and left sides • Seven latches on the bottom. 2. Secure the display mask with two M2.5×6 black flat-head screws. NOTE: Hold the display by the back with your hand while tightening the screws.
PAGE 279
4.23 FL Inverter Board 4 Replacement Procedures 4.23 FL Inverter Board Removing the FL Inverter Board To remove the FL inverter board, follow the steps below and refer to Figures 4-46 and 4-47. 1. Remove one M2×4 flat-head screw securing the FL inverter board. 2. Turn over the insulator securing the HV cable.
PAGE 280
4 Replacement Procedures 4.23 FL Inverter Board 3. Rotate out the FL inverter board and disconnect the FL cable from CN1 on the FL inverter board. 4. Disconnect the HV cable from CN2 on the FL inverter board. 5. Remove the FL inverter board.
PAGE 281
4.23 FL Inverter Board 4 Replacement Procedures Installing the FL Inverter Board To install the FL inverter board, follow the steps below and refer to Figures 4-46 and 4-47. 1. Connect the FL inverter cable to CN1 and the HV cable to CN2. 2. Seat the FL inverter board. 3. Secure the FL inverter board with one M2×4 flat-head screw. 4. Secure the HV cable with the insulator.
PAGE 282
4 Replacement Procedures 4.24 LCD Module 4.24 LCD Module NOTE: Be careful not to apply pressure to the ICs along the edge of LCD module. The ICs are easily damaged. NOTE: For environmental reasons, do not throw away a malfunctioning LCD module (or FL). Please follow local ordinances or regulations for its disposal. Removing the LCD Module To remove the LCD Module, follow the steps below and refer to Figures 4-48 to 4-50. 1. Remove four masking seals that cover the screws. 2.
PAGE 283
4.24 LCD Module 4 Replacement Procedures 3. Carefully rotate out the top of the LCD module to access the LCD/FL cable. 4. Remove the tape securing the LCD/FL cable. 5. Disconnect the LCD/FL cable. 6. Remove the LCD module.
PAGE 284
4 Replacement Procedures 4.24 LCD Module 7. Remove four silver super flat-head M2×3 screws securing two metal braces.
PAGE 285
4.24 LCD Module 4 Replacement Procedures Installing the LCD Module To install the LCD module, follow the steps below and refer to Figures 4-48 to 4-50. 1. Seat two metal braces and secure each with two silver super flat-head M2×3 screws. 2. Connect the LCD/FL cable to the LCD module. 3. Secure the LCD/FL cable with the tape. 4. Seat the LCD module and secure it with four M2×4 flat-head screws. CAUTION: Make sure the cables lie inside the guide.
PAGE 286
4 Replacement Procedures 4.25 Antenna Coaxial Cables 4.25 Antenna Coaxial Cables Removing the Antenna Coaxial Cables To remove the antenna coaxial cables, follow the steps below and refer to Figures 4-51 to 453. NOTE: When you open or close the top cover, hold it by the sides close to the hinges to prevent damage. 1. Turn over the insulator securing the antenna coaxial cables. 2. Free the antenna coaxial cables from their hooks.
PAGE 287
4.25 Antenna Coaxial Cables 4 Replacement Procedures 3. Turn over the insulator securing the antenna coaxial cables. 4. Remove a strip of tape covering the antenna coaxial cables. 5. Free the antenna coaxial cables from their groove. 6. Remove two M2.5×4 black flat-head screws securing the plastic cover. 7. Remove the plastic cover. M2.
PAGE 288
4 Replacement Procedures 4.25 Antenna Coaxial Cables 8. Turn the computer right side up and open the display panel. 9. Pull out the antenna coaxial cables from the hinge. 10. Remove four strips of tape securing the antenna coaxial cables. 11. Remove the antennas.
PAGE 289
4.25 Antenna Coaxial Cables 4 Replacement Procedures Installing the Antenna Coaxial Cables To install the antenna coaxial cables, follow the steps below and refer to Figures 4-51 to 4-53. 1. Seat the antennas and route the antenna coaxial cables. 2. Secure the antenna coaxial cable with four strips of tape. 3. Thread the antenna coaxial cable through the hinge. 4. Close the display panel. 5. Seat the plastic cover and secure it with two M2.5×4 black flat-head screws. 6.
PAGE 290
4 Replacement Procedures 4.26 LCD/FL Cable 4.26 LCD/FL Cable Removing the LCD/FL Cable To remove the LCD/FL cable and antenna coaxial cable, follow the steps below and refer to Figures 4-54 to 4-56. NOTE: When you open or close the top cover, hold it by the sides close to the hinges to prevent damage. 1. Remove two M2.5×4 black flat-head screws securing the plastic cover. 2. Remove the plastic cover. M2.
PAGE 291
4.26 LCD/FL Cable 4 Replacement Procedures 3. Turn the computer right side up and open the display panel. 4. Remove one M2.5×6 tapping screw securing the metal brace. 5. Remove the metal brace. M2.
PAGE 292
4 Replacement Procedures 4.26 LCD/FL Cable 6. Close the display panel. 7. Remove the LCD/FL cable. LCD/FL cable Figure 4-56 Removing the LCD/FL cable Installing the LCD/FL Cable To install the LCD/FL cable, follow the steps below and refer to Figures 4-54 to 4-56. 1. Route the LCD/FL cable. 2. Seat the metal plate and secure it with one M2.5×6 tapping screw. 3. Set the plastic brace and the metal plate. 4. Seat the plastic cover and secure it with two M2.5×4 black flat-head screws.
PAGE 293
4.27 TFT FL (Model 14.1 XGA Samsung LTN141XF-L02) 4 Replacement Procedures 4 4.27 TFT FL (Model 14.1 XGA Samsung LTN141XF-L02) Removing the TFT FL (Model 14.1 XGA Samsung LTN141XF-L02) To remove the TFT FL (Model 14.1 XGA Samsung LTN141XF-L02), follow the steps below and refer to Figures 4-57 to 4-65. 1. Flip the LCD module over and remove the PCB cover and three pieces of tape. CAUTION: Use care not to damage the PCB.
PAGE 294
4 Replacement Procedures 4.27 TFT FL (Model 14.1 XGA Samsung LTN141XF-L02) 2. Remove the two screws for fixing the power supply board. CAUTION: Use care not to damage the PCB.
PAGE 295
4.27 TFT FL (Model 14.1 XGA Samsung LTN141XF-L02) 4 Replacement Procedures 3. Release the 18 hooks and remove the upper chassis from the frame. There are six hooks at the top, four hooks on each of the left- and right-hand sides, and four hooks at the bottom.
PAGE 296
4 Replacement Procedures 4.27 TFT FL (Model 14.1 XGA Samsung LTN141XF-L02) 4. Remove the panel assembly from the backlight assembly. CAUTION: Use care not to damage the TCP during working.
PAGE 297
4.27 TFT FL (Model 14.1 XGA Samsung LTN141XF-L02) 4 Replacement Procedures 5. Remove the two clips. 6.
PAGE 298
4 Replacement Procedures 4.27 TFT FL (Model 14.1 XGA Samsung LTN141XF-L02) 7. Remove the two screws for fixing the back cover of the FL tube.
PAGE 299
4.27 TFT FL (Model 14.1 XGA Samsung LTN141XF-L02) 4 Replacement Procedures 8. Disconnect the ground wire of the FL tube from the frame.
PAGE 300
4 Replacement Procedures 4.27 TFT FL (Model 14.1 XGA Samsung LTN141XF-L02) 9. Remove the FL tube from the frame.
PAGE 301
4.27 TFT FL (Model 14.1 XGA Samsung LTN141XF-L02) 4 Replacement Procedures Installing the TFT FL (Model 14.1 XGA Samsung LTN141XF-L02) To install the TFT FL (Model 14.1 XGA Samsung LTN141XF-L02), follow the steps below and refer to Figures 4-57 to 4-65. 1. Place the FL tube on the correct location in the frame. 2. Connect the ground wire to the frame. 3. Fix the back cover of the FL tube with the two screws. 4. Attach these: • Reflective sheet • Light guide plate (LGP) • Diffuser sheet • Prism sheet 5.
PAGE 302
4 Replacement Procedures 4.28 TFT FL (Model 14.1 XGA LG. Philips LP141X7-C1TO) 4.28 TFT FL (Model 14.1 XGA LG. Philips LP141X7-C1TO) Removing the TFT FL (Model 14.1 XGA LG. Philips LP141X7-C1TO) To remove the TFT FL (Model 14.1 XGA LG. Philips LP141X7-C1TO), follow the steps below and refer to figures 4-66 to 4-69. Removing the outside tape/cover tape 1. Remove the tape adhesive (1) used for the B/L wire fixing. CAUTION: Pressure or stress should not be given on the B/L wire 2.
PAGE 303
4.28 TFT FL (Model 14.1 XGA LG.
PAGE 304
4 Replacement Procedures 4.28 TFT FL (Model 14.1 XGA LG. Philips LP141X7-C1TO) Removing the control PCB, top case and cover assembly 6. Remove the FPC cable (1) used for the control PCB connecting. CAUTION: Pressure or stress should not be given on the FPC cable. 7. Remove the control PCB (2). CAUTION: At first, move the control PCB to the left 8. Remove the top case (3) CAUTION: Pressure or stress should not be given on the top case and gate TCP 9. Remove the screw and cover assembly (4).
PAGE 305
4.28 TFT FL (Model 14.1 XGA LG. Philips LP141X7-C1TO) 4 Replacement Procedures Removing the source PCB and gate PCB 10. Remove the source PCB (1). CAUTION: Pressure or stress should not be given on the PCB and TCP during removing double tape. 11. Remove the gate PCB (2). CAUTION: Pressure or stress should not be given on the PCB and TCP during removing double tape.
PAGE 306
4 Replacement Procedures 4.28 TFT FL (Model 14.1 XGA LG. Philips LP141X7-C1TO) Removing the board assembly, tape pad sheet, light guide, cover bottom and lamp assembly 12. Remove the board assembly (1). CAUTION: This process should be made in the clean room with no scratch nor particle on the Polarize and B/L assembly . 13. Remove the tape pad (2) used for sheets fixing. 14. Remove the sheets and light guide (3).
PAGE 307
4.28 TFT FL (Model 14.1 XGA LG.
PAGE 308
4 Replacement Procedures 4.28 TFT FL (Model 14.1 XGA LG. Philips LP141X7-C1TO) Installing the TFT FL (Model 14.1 XGA LG. Philips LP141X7-C1TO) To install the TFT FL (Model 14.1 LG. XGA Philips LP141X7-C1TO), follow the steps below and refer to figures 4-69 to 4-72. Attaching the double tape, lamp assembly, cover bottom, sheets, light guide, tape adhesive and board assembly 1. Attach the lamp assembly with the double tape (1). (Lamp housing fixing) 2.
PAGE 309
4.28 TFT FL (Model 14.1 XGA LG.
PAGE 310
4 Replacement Procedures 4.28 TFT FL (Model 14.1 XGA LG. Philips LP141X7-C1TO) Attaching the source PCB and gate PCB 9. Attach the source PCB (1). CAUTION: Stress should not be given on the TCP. 10. Attach the gate PCB (2). CAUTION: Stress should not be given on the TCP.
PAGE 311
4.28 TFT FL (Model 14.1 XGA LG. Philips LP141X7-C1TO) 4 Replacement Procedures Attaching the cover bottom, screw, top case, control PCB and FPC 11. Attach the bottom cover and screw (1). CAUTION: Pressure should not be given on the source TCP. 12. Attach the top case (2). CAUTION: Pressure should not be given on the gate TCP. 13. Attach the control PCB (3). CAUTION: Move the control PCB to the right. 14. Attach the FPC cable (4) used for the control PCB connecting.
PAGE 312
4 Replacement Procedures 4.28 TFT FL (Model 14.1 XGA LG. Philips LP141X7-C1TO) Attaching the outside tape and cover shield 15. Attach the tape adhesive (1) used for B/L wire fixing. CAUTION: Pressure or stress should not be given on the B/L wire fixing. 16. Attach the tape adhesive (2) used for top case fixing. 17. Attach the cover shield (3). CAUTION: Pressure or stress should not be given on the control PCB.
PAGE 313
4.28 TFT FL (Model 14.1 XGA LG.
PAGE 314
4 Replacement Procedures 4.29 TFT FL (Model 15.0 XGA Samsung LTN150X6-L01) 4 4.29 TFT FL (Model 15.0 XGA Samsung LTN150X6-L01) Removing the TFT FL (Model 15.0 XGA Samsung LTN150X6-L01) CAUTION: Exercise care during FL removal not to damage the LCD panel and not to let dust or other foreign matter into the LCD panel. Foreign matter is detrimental to the display quality of the LCD. To remove the TFT FL (Model 15.0 XGA Samsung LTN150X6-L01), follow the steps below and refer to Figures 4-73 to 4-81. 1.
PAGE 315
4.29 TFT FL (Model 15.0 XGA Samsung LTN150X6-L01) 4 Replacement Procedures 2. Remove two screws securing the PCB. Screw Screw Figure 4-74 Removing the screws securing the PCB 3. Remove four screws on the right and left sides of the chassis.
PAGE 316
4 Replacement Procedures 4.29 TFT FL (Model 15.0 XGA Samsung LTN150X6-L01) 4. Release eight hooks (four hooks on the bottom side first and four hooks on the right and left side) and remove the top chassis from the LCD module starting from the bottom end. CAUTION: When you release hooks on the top chassis, be careful not to apply pressure to the FL. The FL can be damaged easily.
PAGE 317
4.29 TFT FL (Model 15.0 XGA Samsung LTN150X6-L01) 4 Replacement Procedures 5. Turn the LCD module face up and remove the panel assembly from the mold-frame. Handle with care not to damage COF.
PAGE 318
4 Replacement Procedures 4.29 TFT FL (Model 15.0 XGA Samsung LTN150X6-L01) 6. Remove two clips and six sheets (protector, prism(L,U), diffuser, LGP, and reflector sheet) from the back light assembly.
PAGE 319
4.29 TFT FL (Model 15.0 XGA Samsung LTN150X6-L01) 4 Replacement Procedures 7. Turn the back light assembly face down and remove two screws to remove the lamp cover from the mold frame.
PAGE 320
4 Replacement Procedures 4.29 TFT FL (Model 15.0 XGA Samsung LTN150X6-L01) 8. Free the HV cable from the mold-frame’s cable guide.
PAGE 321
4.29 TFT FL (Model 15.0 XGA Samsung LTN150X6-L01) 4 Replacement Procedures 9. Pull the FL assembly out of its groove on the mold frame.
PAGE 322
4 Replacement Procedures 4.29 TFT FL (Model 15.0 XGA Samsung LTN150X6-L01) Installing the TFT FL (Model 15.0 XGA Samsung LTN150X6-L01) To install the TFT FL (Model 15.0 XGA Samsung LTN150X6-L01), follow the steps below and refer to Figures 4-73 to 4-81. 1. Seat the FL in its groove on the mold frame. 2. Route the HV cable through its guide. 3. Lay the lamp cover on the mold frame and secure it with two screws. 4. Lay six sheets on the back light assembly and secure them with two clips. 5.
PAGE 323
4.30 TFT FL (Model 15.0 XGA LG. Philips LP150X06 A2) 4 Replacement Procedures 4.30 TFT FL (Model 15.0 XGA LG. Philips LP150X06 A2) CAUTION: When you replace the fluorescent lamp, wear finger covers or gloves to avoid contaminating or damaging the LCD panel. Be careful not to let dust or other foreign matter into the module. Removing the TFT FL (Model 15.0 XGA LG. Philips LP150X06 A2) To remove the TFT FL (Model 15.0 XGA LG. Philips LP150X06 A2), follow the steps below and refer to figures 4-82 to 4-85. 1.
PAGE 324
4 Replacement Procedures 4.30 TFT FL (Model 15.0 XGA LG. Philips LP150X06 A2) 5. Disassembly of Top Case. Pressure or stress should not be given on Top Case and Gate TCP.
PAGE 325
4.30 TFT FL (Model 15.0 XGA LG. Philips LP150X06 A2) 4 Replacement Procedures 6. Disassembly of Source PCB. Pressure or stress should not be given on PCB and TCP during removing double tape. 7. Disassembly of Gate PCB. Pressure or stress should not be given on PCB and TCP during removing double tape.
PAGE 326
4 Replacement Procedures 4.30 TFT FL (Model 15.0 XGA LG. Philips LP150X06 A2) 8. Disassembly of Board Ass’y. This process should be made in Clean room with no scratch nor particle on Polarizer and B/L Ass’y. 9. Disassembly of Tape Adhesive used for Sheets fixing (4 Point). 10. Disassembly of Sheets and Light guide. No penetration of foreign body is indispensable with no scratch on the surface of each Sheets. 11. Disassembly of Screw and Cover Ass’y bottom (L).
PAGE 327
4.30 TFT FL (Model 15.0 XGA LG. Philips LP150X06 A2) 4 Replacement Procedures Installing the TFT FL (Model 15.0 XGA LG. Philips LP150X06 A2) To install the TFT FL (Model 15.0 LG. XGA Philips LP150X06 A2), follow the steps below and refer to Figures 4-86 to 4-89. 1. Detach a protect film from Double Tape at the Cover Ass’y Bottom(L) 2. Assembly of Cover Ass’y bottom(L) and Screw. Maximum value of torque with Screw should be below 2.0kgf.cm 3. Assembly of Light guide and Sheets.
PAGE 328
4 Replacement Procedures 4.30 TFT FL (Model 15.0 XGA LG. Philips LP150X06 A2) 6. Assembly of Source PCB. Stress should not be given on TCP 7. Assembly of Gate PCB.
PAGE 329
4.30 TFT FL (Model 15.0 XGA LG. Philips LP150X06 A2) 8. 4 Replacement Procedures Assembly of Top Case. Pressure should not be given on Source TCP.
PAGE 330
4 Replacement Procedures 4.30 TFT FL (Model 15.0 XGA LG. Philips LP150X06 A2) 9. Assembly of Tape shield and Tape Adhesive used for Top case fixing. Pressure or stress should not be given on Top case during this process 10. Assembly of Cover shield (C). Pressure or stress should not be given on control PCB. Usage of gloves with anti-electric discharge coating is recommended. To eliminate possible damage on circuits occurred by ESC. 11. Assembly of Cover shield (G).
PAGE 331
4.31 TFT FL (Model 15.0 XGA Chi Mei N150X2-L01) 4 Replacement Procedures 4.31 TFT FL (Model 15.0 XGA Chi Mei N150X2-L01) Removing the TFT FL (Model 15.0 XGA Chi Mei N150X2-L01) To remove the TFT FL (Model 15.0 XGA Chi Mei N150X2-L01), follow the steps below and refer to figures 4-90 to 4-95. 1. Remove the CU tape, yellow tape and protector film_X.
PAGE 332
4 Replacement Procedures 4.31 TFT FL (Model 15.0 XGA Chi Mei N150X2-L01) 2. Remove two screws securing the X-PCB. 3. Remove eight screws securing the metal frame. 4. Release a hook. Screw Screw Screw Screw Metal frame Screw Detail of the hook Screw Screw Screw Screw Screw Figure 4-91 Removing the screws securing the X-PCB and metal frame.
PAGE 333
4.31 TFT FL (Model 15.0 XGA Chi Mei N150X2-L01) 4 Replacement Procedures 5. Push the latch out of lower frame from the lamp holder and then the latch on both sides. Be careful not to distort the frame.
PAGE 334
4 Replacement Procedures 4.31 TFT FL (Model 15.0 XGA Chi Mei N150X2-L01) 6. Unfold the X-PCB. Be careful not to distort the TCP. 7. Turn the LCD module right side up. 8. Remove the panel.
PAGE 335
4.31 TFT FL (Model 15.0 XGA Chi Mei N150X2-L01) 4 Replacement Procedures 9. Remove three spacers from the BEFIII-M sheet. 10. Remove the BEFIII-M sheet, BEFIII-T sheet, diffuser sheet, and two strips of tape. Be careful not to damage the sheets.
PAGE 336
4 Replacement Procedures 4.31 TFT FL (Model 15.0 XGA Chi Mei N150X2-L01) 11. Remove two screws securing the FL. 12. Remove the FL.
PAGE 337
4.31 TFT FL (Model 15.0 XGA Chi Mei N150X2-L01) 4 Replacement Procedures Installing the TFT FL (Model 15.0 XGA Chi Mei N150X2-L01) To install the TFT FL (Model 15.0 XGA Chi Mei N150X2-L01), follow the steps below and refer to Figures 4-90 to 4-95. 1. Seat the FL and secure it with two screws. 2. Seat the diffuser sheet, BEMIII-T sheet and the BEFIII-M sheet. 3. Apply two strips of tape to the LCD module. 4. Apply three spacers to the BEFIII-M sheet. 5. Seat the panel. 6. Turn the LCD module upside down.
PAGE 338
4 Replacement Procedures 4.32 TFT FL (Model 15.0 SXGA+ Samsung LTN150P3-L03) 4 4.32 TFT FL (Model 15.0 SXGA+ Samsung LTN150P3-L03) Removing the TFT FL (Model 15.0 SXGA+ Samsung LTN150P3-L03) CAUTION: Exercise care during FL removal not to damage the LCD panel and not to let dust or other foreign matter into the LCD panel. Foreign matter is detrimental to the display quality of the LCD. To remove the TFT FL (Model 15.0 SXGA+ Samsung LTN150P3-L03), follow the steps below and refer to Figures 4-96 to 4-104.
PAGE 339
4.32 TFT FL (Model 15.0 SXGA+ Samsung LTN150P3-L03) 4 Replacement Procedures 2. Remove two screws securing the PCB.
PAGE 340
4 Replacement Procedures 4.32 TFT FL (Model 15.0 SXGA+ Samsung LTN150P3-L03) 3. Remove four screws on the right and left sides of the chassis.
PAGE 341
4.32 TFT FL (Model 15.0 SXGA+ Samsung LTN150P3-L03) 4 Replacement Procedures 4. Release nine hooks (four hooks on the bottom side first and five hooks on the right and left side) and remove the top chassis from the LCD module starting from the bottom end. CAUTION: When you release hooks on the top chassis, be careful not to apply pressure to the FL. The FL can be damaged easily.
PAGE 342
4 Replacement Procedures 4.32 TFT FL (Model 15.0 SXGA+ Samsung LTN150P3-L03) 5. Turn the LCD module face up and remove the panel assembly from the mold-frame.
PAGE 343
4.32 TFT FL (Model 15.0 SXGA+ Samsung LTN150P3-L03) 4 Replacement Procedures 6. Remove two clips and five sheets (prism(L,U), diffuser, LGP, and reflector sheet) from the back light assembly.
PAGE 344
4 Replacement Procedures 4.32 TFT FL (Model 15.0 SXGA+ Samsung LTN150P3-L03) 7. Turn the back light assembly face down and remove two screws to remove the lamp cover from the mold frame.
PAGE 345
4.32 TFT FL (Model 15.0 SXGA+ Samsung LTN150P3-L03) 4 Replacement Procedures 8. Free the HV cable from the mold-frame’s cable guide.
PAGE 346
4 Replacement Procedures 4.32 TFT FL (Model 15.0 SXGA+ Samsung LTN150P3-L03) 9. Pull the FL assembly out of its groove on the mold frame.
PAGE 347
4.32 TFT FL (Model 15.0 SXGA+ Samsung LTN150P3-L03) 4 Replacement Procedures Installing the TFT FL (Model 15.0 SXGA+ Samsung LTN150P3-L03) To install the TFT FL (Model 15.0 SXGA+ Samsung LTN150P3-L03), follow the steps below and refer to Figures 4-96 to 4-104. 1. Seat the FL in its groove on the mold frame. 2. Route the HV cable through its guide. 3. Lay the lamp cover on the mold frame and secure it with two screws. 4. Lay five sheets on the back light assembly and secure them with two clips. 5.
PAGE 348
4 Replacement Procedures 4.33 TFT FL (Model 15.0 SXGA+ SHARP LQ150F1LH43) 4.33 TFT FL (Model 15.0 SXGA+ SHARP LQ150F1LH43) Removing the TFT FL (Model 15.0 SXGA+ SHARP LQ150F1LH43) To remove the TFT FL (Model 15.0 SXGA+ SHARP LQ150F1LH43), follow the steps below and refer to Figures 4-105 to 4-113. 1. Turn the LCD module upside down. 2. Remove the protective cover-S, protective cover-G, fixing tape, and HV cable fixing tape. Be careful not to damage the TCP or ICs.
PAGE 349
4.33 TFT FL (Model 15.0 SXGA+ SHARP LQ150F1LH43) 4 Replacement Procedures 3. Remove four screws from the side of the LCD module. Screw Screw Loosen the screws with 1.1kgf⋅cm of torque. Screw Screw Figure 4-106 Removing the screws 4. Turn the LCD module right side up. 5. Remove the top frame. When you remove it, wear gloves or finger guards to avoid contaminating or damaging the LCD panel. 3 Release the U-shaped side of the top frame.
PAGE 350
4 Replacement Procedures 4.33 TFT FL (Model 15.0 SXGA+ SHARP LQ150F1LH43) 6. Turn the LCD module upside down. 7. Remove four screws securing the PCBs. 8. Disconnect the FPC. 9. Fold out the PCBs. Screw Screw Screw Open the connector cover and disconnect the connector. FPC Loosen the screws with 0.9kgf¥cm of torque. Do not grasp both ends. Screw Do not grasp both ends. Fold out the PCBs as this illustration.
PAGE 351
4.33 TFT FL (Model 15.0 SXGA+ SHARP LQ150F1LH43) 4 Replacement Procedures 10. Turn the LCD module right side up. 11. Remove the LCD panel from the backlight unit. When you remove the LCD panel, wear finger covers or gloves to avoid contaminating or damaging the LCD panel and the backlight unit.
PAGE 352
4 Replacement Procedures 4.33 TFT FL (Model 15.0 SXGA+ SHARP LQ150F1LH43) 12. Turn the backlight unit upside down taking care not to damage or contaminate the sheets. 13. Remove two screws securing the lamp cover to remove it. Loosen the screws with 1.1kgf¥cm of torque.
PAGE 353
4.33 TFT FL (Model 15.0 SXGA+ SHARP LQ150F1LH43) 4 Replacement Procedures 14. Turn the backlight unit right side up. 15. Remove the upper diffuser sheet, lens sheet, and light guide sheet. Be careful not to damage or contaminate the sheets because they are reused. Upper diffuser sheet Lens sheet Light guide sheet Figure 4-111 Removing the sheets 16. Remove four strips of double-faced tape, and dispose of them.
PAGE 354
4 Replacement Procedures 4.33 TFT FL (Model 15.0 SXGA+ SHARP LQ150F1LH43) 17. Turn the backlight unit upside down. 18. Gentry remove the FL taking care not to damage it. P-chassis FL Figure 4-113 Removing the FL NOTE: Be careful not to fold the reflective sheet back when you remove the FL assembly.
PAGE 355
4.33 TFT FL (Model 15.0 SXGA+ SHARP LQ150F1LH43) 4 Replacement Procedures Installing the TFT FL (Model 15.0 SXGA+ SHARP LQ150F1LH43) To install the TFT FL (Model 15.0 SXGA+ SHARP LQ150F1LH43), follow the steps below and refer to Figures 4-114 to 4-126. 1. Apply four strips of double-faced tape to the frame. Double-face tape (3) Apply the tape along the indentation in the frame. Do not let any tape protrude beyond the indentation.
PAGE 356
4 Replacement Procedures 4.33 TFT FL (Model 15.0 SXGA+ SHARP LQ150F1LH43) 2. Install a new FL unit into the frame. Frame FL Z Z Install the FL into the frame making sure it does not stick out from the frame. Let the reflective sheet inside the reflector Fit the wire firmly into the groove Cross section of Z—Z Figure 4-115 Installing the FL NOTE: Be careful not to fold the reflective sheet when you install the FL unit.
PAGE 357
4.33 TFT FL (Model 15.0 SXGA+ SHARP LQ150F1LH43) 4 Replacement Procedures 3. Seat the lamp cover on the backlight unit and secure it with two screws. Lamp cover Tighten the screws with 0.9kgf•cm of torque. Screw Screw Figure 4-116 Installing the lamp cover 4. Install the light guide sheet in the backlight unit. Insert the light guide sheet straight to avoid deforming any sheets.
PAGE 358
4 Replacement Procedures 4.33 TFT FL (Model 15.0 SXGA+ SHARP LQ150F1LH43) 5. Strip all of the liner on the double-faced tape applied to the frame. 6. Lay the lens sheet and upper diffuser sheet on the backlight unit. Be careful not to contaminate or damage any sheets. Lens sheet Upper diffuser sheet Light guide sheet Be careful not to contaminate or damage any sheets. Do not let any sheets lie on the rib of the frame. Do not let any sheets lie on the rib of the frame.
PAGE 359
4.33 TFT FL (Model 15.0 SXGA+ SHARP LQ150F1LH43) 4 Replacement Procedures 7. Seat the LCD panel on the backlight unit assembled by the steps above. Make sure there are no dust between the LCD panel and the backlight. If you find any foreign matter, remove it. 8. Make sure the LCD panel fits into the panel guide ribs. LCD panel Guide rib Backlight unit Make sure the LCD panel fits into the panel guide ribs.
PAGE 360
4 Replacement Procedures 4.33 TFT FL (Model 15.0 SXGA+ SHARP LQ150F1LH43) 9. Fold the TCP of the source PCB down. 10. Secure the source PCB with two screws. 11. Fold the TCP of the gate PCB down. 12. Secure the gate PCB with two screws. TCP of source PCB Do not grasp both ends. Do not grasp both ends.
PAGE 361
4.33 TFT FL (Model 15.0 SXGA+ SHARP LQ150F1LH43) 4 Replacement Procedures 13. Connect the FPC to the connector on the source PCB. Make sure the latch secures the connector correctly. See the notches on both the edge of the FPC, and see the contour of the connector. Insert the FPC into the connector firmly. The FPC must have no inclination. Lock the connector firmly. NG: The FPC has inclination. Source PCB Pin* Screw NG: The FPC does not connect firmly.
PAGE 362
4 Replacement Procedures 4.33 TFT FL (Model 15.0 SXGA+ SHARP LQ150F1LH43) 14. Install the top frame. Secure the top frame and the lamp cover with six latches. Top frame Hook the U-shaped side of the top frame to the P-chassis. Lay the top frame on the lamp cover. Be sure the top frame does not interfere with the TCP.
PAGE 363
4.33 TFT FL (Model 15.0 SXGA+ SHARP LQ150F1LH43) 4 Replacement Procedures 15. Secure four screws on the side of the module. Screw Screw Tighten the screws with 0.9kgf⋅cm of torque. Screw Screw Figure 4-123 Securing the screws 16. Apply the protective cover-G. Align the edge of the cover with the edge of the gate PCB.
PAGE 364
4 Replacement Procedures 4.33 TFT FL (Model 15.0 SXGA+ SHARP LQ150F1LH43) 17. Apply the protective cover-S. Apply the cover along the top frame and fold the cover to the side. Align the cover's edge with the edge of the plastic part of the connector Make sure that the amount of displacement is ±0.5 mm or less. The edge of the plastic part of the connector 0 to 1 mm Align the cover's edge with the PCB's edge. 0 to 1 mm Apply the cover's edge close to the screw.
PAGE 365
4.33 TFT FL (Model 15.0 SXGA+ SHARP LQ150F1LH43) 4 Replacement Procedures 18. Apply the fixing tape and the HV cable fixing tape. Secure the cable with tape. Be sure the cable lies flat. 0 to 1 mm HV cable fixing tape Fixing tape Apply the fixing tape around the center of the module. Be sure not to let the tape protrude beyond the frame side. 0 to 0.5mm Be sure not to let the tape lie on the screen of the LCD. Align the end of the tape with the edge of the module.
PAGE 366
4 Replacement Procedures 4.34 TFT FL (Model 15.0 UXGA SHARP LQ150U1LW13) 4.34 TFT FL (Model 15.0 UXGA SHARP LQ150U1LW13) CAUTION: When you replace the fluorescent lamp, wear finger covers or gloves to avoid contaminating or damaging the LCD panel. Be careful not to let dust or other foreign matter into the module. Removing the TFT FL (Model 15.0 UXGA SHARP LQ150U1LW13) To remove the TFT FL (Model 15.0 UXGA SHARP LQ150U1LW13), follow the steps below and refer to Figures 4-127 to 4-135. 1.
PAGE 367
4.34 TFT FL (Model 15.0 UXGA SHARP LQ150U1LW13) 4 Replacement Procedures 3. Remove five screws from the side of the LCD module. Loosen the screws with 1.0 kgf•com of torque. Screw Screw Screw Screw Screw Figure 4-128 Removing the screws 4. Turn the LCD module right side up. 5. Remove the top frame. When you remove it, wear gloves or finger guards to avoid staining or damaging the LCD panel. Release the U-shaped side of the top frame.
PAGE 368
4 Replacement Procedures 4.34 TFT FL (Model 15.0 UXGA SHARP LQ150U1LW13) 6. Turn the LCD module upside down. 7. Remove five screws securing the PCBs. 8. Disconnect the FPC. Screw Screw Screw Screw FPC Open the connector cover and disconnect the connector. Screw Loosen the screws with 1.0kgf¥cm of torque. Figure 4-130 Removing five screws and disconnecting the FPC 9. Fold out the PCBs. Do not grasp both ends. Do not grasp both ends. Fold out the PCBs as this illustration.
PAGE 369
4.34 TFT FL (Model 15.0 UXGA SHARP LQ150U1LW13) 4 Replacement Procedures 10. Turn the LCD module right side up. 11. Remove the LCD panel from the backlight unit. When you remove the LCD panel, wear finger covers or gloves to avoid staining or damaging the LCD panel and the backlight unit. LCD panel Backlight unit Figure 4-132 Removing the LCD panel 12. Turn the backlight unit upside down taking care not to damage or stain the sheets. 13. Remove two screws securing the lamp cover to remove it.
PAGE 370
4 Replacement Procedures 4.34 TFT FL (Model 15.0 UXGA SHARP LQ150U1LW13) 14. Turn the backlight unit right side up. 15. Remove three strips of shield tape, the optical sheet, the upper lens sheet, the lower lens sheet, the lower diffuser sheet and the light guide sheet. Be careful not to damage or stain the sheets because they are reused. Dispose of the removed shield tape.
PAGE 371
4.34 TFT FL (Model 15.0 UXGA SHARP LQ150U1LW13) 4 Replacement Procedures Installing the TFT FL (Model 15.0 UXGA SHARP LQ150U1LW13) To install the TFT FL (Model 15.0 UXGA SHARP LQ150U1LW13), follow the steps below and refer to Figures 4-136 to 4-147. 1. Install a new FL unit into the frame. Frame FL Z Z Install the FL into the frame making sure it does not stick out from the frame.
PAGE 372
4 Replacement Procedures 4.34 TFT FL (Model 15.0 UXGA SHARP LQ150U1LW13) 2. Seat the lamp cover on the backlight unit and secure it with two screws. Backlight unit Lamp cover V W Tighten the screws with 1.0kgf•cm of torque. Screw Screw Detail of V Detail of W Align the holes on the lamp cover with the pins on the frame. Figure 4-137 Installing the lamp cover 3. Install the light guide sheet in the backlight unit. 3 Insert the light guide sheet straight to avoid deforming any sheets.
PAGE 373
4.34 TFT FL (Model 15.0 UXGA SHARP LQ150U1LW13) 4 Replacement Procedures 4. Lay the lower diffuser sheet, the lower lens sheet, the upper lens sheet and the optical sheet on the backlight unit. Be careful not to stain or damage any sheets. Shield tape Shield tape Optical sheet Upper lens sheet Lower lens sheet X Y Lower diffuser sheet Light guide sheet Backlight unit Pin Allign the sheet with pin when you lay the sheet.
PAGE 374
4 Replacement Procedures 4.34 TFT FL (Model 15.0 UXGA SHARP LQ150U1LW13) 5. Seat the LCD panel on the backlight unit assembled by the steps above. Make sure there is no dust between the LCD panel and the backlight unit. If you find any foreign matter, remove it. LCD panel Guide rib Backlight unit Make sure the LCD panel fits into the panel guide ribs. Figure 4-140 Installing the LCD panel 6. Fold the TCP of the source PCB, then the TCP of the gate PCB down. TCP of source PCB Do not grasp both ends.
PAGE 375
4.34 TFT FL (Model 15.0 UXGA SHARP LQ150U1LW13) 4 Replacement Procedures 7. Secure the TCP of the source PCB with three screws. 8. Secure the TCP of the gate PCB with two screws. 9. Connect the FPC to the connector on the source PCB. Make sure the latch secures the connector correctly. See the notches on both the edge of the FPC, and see the contour of the connector. Insert the FPC into the connector firmly. The FPC must have no inclination. Lock the connector firmly. NG: The FPC has inclination.
PAGE 376
4 Replacement Procedures 4.34 TFT FL (Model 15.0 UXGA SHARP LQ150U1LW13) 10. Install the top frame. Top frame Hook the U-shaped side of the top frame to the P-chassis. Lay the top frame on the lamp cover. Be sure the top frame does not interfere with the TCP. Figure 4-143 Installing the top frame 11. Secure the top frame and the lamp cover with four latches.
PAGE 377
4.34 TFT FL (Model 15.0 UXGA SHARP LQ150U1LW13) 4 Replacement Procedures 12. Secure five M2×2 screws on the side of the module. Screw Screw Screw Tighten the screws with 1.0 kgf•cm of torque. Screw Screw Figure 4-145 Securing the screws 13. Apply the protective cover-G.
PAGE 378
4 Replacement Procedures 4.34 TFT FL (Model 15.0 UXGA SHARP LQ150U1LW13) 14. Apply the protective cover-S, the aluminum tape and the wire-protective tape. Apply the protective cover-S along the top frame and fold the cover to the side. Protective cover-S Align the holes on the protective cover with the pins on the P-chassis. Secure the cable with wire-protective tape. Be sure the cable lies flat.
PAGE 379
Appendices
PAGE 380
Appendices App-ii Satellite Pro M10 Series Maintenance Manual (960-431)
PAGE 381
Appendices Appendix Contents Appendix A Handling the LCD Module .......................................................................... A-1 Appendix B Board Layout .................................................................................................B-1 B.1 System Board (FQDSY*) Front View ...................................................................B-1 B.2 System Board (FQDSY*) Back View....................................................................B-4 B.
PAGE 382
Appendices C.19 PJ4015 Video Out I/F Connector (2-pin)...........................................................C-23 C.20 PJ4900 Bluetooth I/F Connector (20-pin)..........................................................C-24 C.21 PJ5004 Right Speaker I/F Connector (2-pin).....................................................C-24 C.22 PJ5005 Left Speaker I/F Connector (3-pin) .......................................................C-24 C.23 PJ5006 Sound Board (FQDSD*) I/F Connector (60-pin)...........
PAGE 383
Appendices Appendix D Keyboard Scan/Character Codes................................................................ D-1 Appendix E Key Layout .....................................................................................................E-1 E.1 United States (US) Keyboard.................................................................................E-1 E.2 United Kingdom (UK) Keyboard...........................................................................E-1 E.3 German (GR) Keyboard .......
PAGE 384
Appendices Figures Figure B-1 System board (FQDSY*) layout (front) ........................................................B-1 Figure B-2 System board (FQDSY*) layout (back).........................................................B-4 Figure B-3 VGA board (FQDVG*) layout (front)...........................................................B-7 Figure B-4 VGA board (FQDVG*) layout (back) ...........................................................B-8 Figure B-5 Sound board (FQDSD*) layout (front) .......
PAGE 385
Appendices Tables Table B-1 System board (FQDSY*) layout (front) ........................................................B-2 Table B-2 System board (FQDSY*) layout (back).........................................................B-5 Table B-3 VGA board (FQDVG*) layout (front)...........................................................B-7 Table B-4 VGA board (FQDVG*) layout (back) ...........................................................B-8 Table B-5 Sound board (FQDSD*) layout (front) ..............
PAGE 386
Appendices Table C-23 Sound board (FQDSD*) I/F connector pin assignments (60-pin) ...............C-25 Table C-24 IEEE 1394 I/F connector pin assignments (4-pin).......................................C-26 Table C-25 Cooling fan I/F connector pin assignments (3-pin) .....................................C-26 Table C-26 DC-IN I/F connector pin assignments (4-pin) .............................................C-26 Table C-27 Battery I/F connector pin assignments (10-pin) .................................
PAGE 387
Appendix A Handling the LCD Module Appendix A Appendix A Handling the LCD Module Precautions for handling the LCD module The LCD module can be easily damaged during assembly or disassembly. Observe the following precautions when handling the LCD module: 1. When installing the LCD module in the LCD cover, be sure to seat it so that it is properly aligned and maximum visibility of the display is maintained. 2.
PAGE 388
Appendix A Handling the LCD Module 3. If the panel’s surface gets dirty, wipe it with cotton or a soft cloth. If it is still dirty, try breathing on the surface to create a light condensate and wipe it again. If the surface is very dirty, we recommend a CRT cleaning agent. Apply the agent to a cloth and then wipe the panel’s surface. Do not apply cleanser directly to the panel. CRT Cleaner 4.
PAGE 389
Appendix A Handling the LCD Module 5. Glass is used in the panel, so be careful not to drop it or let it strike a hard object, which could cause breakage or cracks. 6. CMOS-LSI circuits are used in the module, so guard against damage from electrostatic discharge. Be sure to wear a wrist or ankle ground when handling the module.
PAGE 390
Appendix A Handling the LCD Module 7. Do not expose the module to direct sunlight or strong ultraviolet rays for long periods. 8. Do not store the module at temperatures below specifications. Cold can cause the liquid crystals to freeze, lose their elasticity or otherwise suffer damage.
PAGE 391
Appendix A Handling the LCD Module 9. Do not disassemble the LCD module. Disassembly can cause malfunctions. 10. If you transport the module, do not use packing material that contains epoxy resin (amine) or silicon glue (alcohol or oxime). These materials can release gas that can damage the panel’s polarization.
PAGE 392
Appendix A Handling the LCD Module A-6 Satellite Pro M10 Series Maintenance Manual (960-431)
PAGE 393
Appendix B Board Layout Appendices Appendix B Board Layout B.
PAGE 394
Appendices Appendix B Board Layout Table B-1 System board (FQDSY*) layout (front) (1/2) B-2 Mark Number Name (A) PJ123 Keyboard I/F Connector (B) PJ326 Debug Port I/F Connector (C) PJ2003 Touch Pad I/F Connector (D) PJ2015 Mini PCI Card I/F Connector (E) PJ2025 Switch Board (FQDSQ*) I/F Connector (F) PJ4900 Bluetooth I/F Connector (G) PJ5004 Right Speaker I/F Connector (H) PJ5005 Left Speaker I/F Connector (I) PJ5006 Sound Board (FQDSD*) I/F Connector (J) PJ8770 Cooling fa
PAGE 395
Appendix B Board Layout Appendices Table B-1 System board (FQDSY*) layout (front) (2/2) Mark Number Name (AA) DS2004 Battery LED (Green) (AB) DS2005 Battery LED (Orange) (AC) DS2006 HDD LED (AD) DS2008 Slim Select Bay (Green) (AE) DS2009 Slim Select Bay (Orange) (AF) DS2010 Wireless Communication LED (AG) F8800 (AH) X1 (AI) X1500 Clock for RTC (32.
PAGE 396
Appendices B.
PAGE 397
Appendix B Board Layout Appendices Table B-2 System board (FQDSY*) layout (back) (1/1) Mark Number Name (A) PJ100 VGA Board (FQDVG*) I/F Connector (B) PJ117 TOSHIBA Style Bay I/F Connector (C) PJ124 RJ-45 & RJ-11 I/F Connector (D) PJ1001 SO-DIMM Socket Connector 0 (E) PJ1002 SO-DIMM Socket Connector 1 (F) PJ1016 RGB I/F Connector (G) PJ1509 HDD I/F Connector (H) PJ1512 PC Card I/F Connector (I) PJ2007 Docking I/F Connector (J) PJ2017 MDC I/F Connector (K) PJ2018 Modem Ca
PAGE 398
Appendices Appendix B Board Layout Table B-2 System board (FQDSY*) layout (back) (2/2) B-6 Mark Number Name (AA) F8810 Fuse for Battery (10A) (AB) F8820 Fuse for Slim Select Bay (10A) (AC) S2302 Wireless Communication Switch (AD) X2002 Clock for Super I/O (14.31818MHz) (AE) X4500 Clock for 82562ET (25MHz) (AF) X6100 Clock for TSB43AB22 (24.
PAGE 399
Appendix B Board Layout B.
PAGE 400
Appendices B.4 Appendix B Board Layout VGA Board (FQDVG*) Back View Figure B-4 VGA board (FQDVG*) layout (back) Table B-4 VGA board (FQDVG*) layout (back) B-8 Mark Number Name (A) IC3002 VGAC GeForce4 420Go (B) IC3004 VRAM DDR SDRAM 128Mbit (4Mx32) (C) F4001 Fuse for LCD (3.
PAGE 401
Appendix B Board Layout B.
PAGE 402
Appendices B.
PAGE 403
Appendix B Board Layout B.
PAGE 404
Appendices B-12 Appendix B Board Layout Satellite Pro M10 Series Maintenance Manual (960-431)
PAGE 405
Apx.C Pin Assignments Appendices Appendix C Appendix C Pin Assignments System Board (FQDSY*) C.1 PJ100 VGA Board (FQDVG*) I/F Connector (200-pin) Table C-1 VGA board (FQDVG*) I/F connector pin assignments (200-pin) (1/3) Pin No. Signal name I/O Pin No.
PAGE 406
Appendices Apx.C Pin Assignments Table C-1 VGA board (FQDVG*) I/F connector pin assignments (200-pin) (2/3) Pin No. C-2 Signal name I/O Pin No.
PAGE 407
Apx.C Pin Assignments Appendices Table C-1 VGA board (FQDVG*) I/F connector pin assignments (200-pin) (3/3) Pin No. I/O Pin No.
PAGE 408
Appendices C.2 Apx.C Pin Assignments PJ117 Slim Select Bay I/F Connector (72-pin) Table C-2 Slim Select Bay I/F connector pin assignments (72-pin) Pin No. C-4 Signal name I/O Pin No.
PAGE 409
Apx.C Pin Assignments C.3 Appendices PJ123 Keyboard I/F Connector (34-pin) Table C-3 Keyboard I/F connector pin assignments (34-pin) Pin No. Signal name I/O Pin No.
PAGE 410
Appendices C.6 Apx.C Pin Assignments PJ1001 SO-DIMM Socket Connector 0 (200-pin) Table C-6 Pin No. C-6 SO-DIMM socket connector 0 pin assignments (200-pin) (1/3) Signal name I/O Pin No.
PAGE 411
Apx.C Pin Assignments Table C-6 Pin No. Appendices SO-DIMM socket connector 0 pin assignments (200-pin) (2/3) Signal name I/O Pin No.
PAGE 412
Appendices Apx.C Pin Assignments Table C-6 Pin No. C-8 SO-DIMM socket connector 0 pin assignments (200-pin) (3/3) Signal name I/O Pin No.
PAGE 413
Apx.C Pin Assignments C.7 Appendices PJ1002 SO-DIMM Socket Connector 1 (200-pin) Table C-7 Pin No. SO-DIMM socket connector 1 pin assignments (200-pin) (1/3) Signal name I/O Pin No.
PAGE 414
Appendices Apx.C Pin Assignments Table C-7 Pin No. C-10 SO-DIMM socket connector 1 pin assignments (200-pin) (2/3) Signal name I/O Pin No.
PAGE 415
Apx.C Pin Assignments Table C-7 Pin No. Appendices SO-DIMM socket connector 1 pin assignments (200-pin) (3/3) Signal name I/O Pin No.
PAGE 416
Appendices C.8 Apx.C Pin Assignments PJ1016 RGB I/F Connector (15-pin) Table C-8 RGB interface connector pin assignments (15-pin) Pin No. Signal name I/O Pin No. Signal name I/O 1 CRTRED-PXP O 2 CRTGRN-PXP O 3 CRTBLU-PXP O 4 NC - 5 GND - 6 GND - 7 GND - 8 GND - 9 P5V O 10 GND - 11 NC - 12 DDCSDA-P5P I/O 13 HSYNC-B3P I/O 14 OVSYNC-B3P I/O 15 DDCSCL-P5P I/O C.9 PJ1509 HDD I/F Connector (44-pin) Table C-9 HDD I/F connector pin assignments (44-pin) Pin No.
PAGE 417
Apx.C Pin Assignments C.10 Appendices PJ1512 PC Card I/F Connector (150-pin) Table C-10 PC Card I/F connector pin assignments (150-pin) (1/2) Pin No. Signal name I/O Pin No.
PAGE 418
Appendices Apx.C Pin Assignments Table C-10 PC Card I/F connector pin assignments (150-pin) (2/2) Pin No. C-14 Signal name I/O Pin No.
PAGE 419
Apx.C Pin Assignments C.11 Appendices PJ2003 Touch Pad I/F Connector (8-pin) Table C-11 Touch Pad I/F connector pin assignments (8-pin) Pin No. Signal name I/O Pin No. Signal name O 2 IPDDAT-P5P 1 P5V 3 IPDCLK-P5P 4 GND 5 SP-GND 6 SPY-PXP 7 SPX-PXP 8 SP-P5V C.12 I/O - PJ2007 Docking I/F Connector (242-pin) Table C-12 Pin No. Docking I/F connector pin assignments (242-pin) (1/4) Signal name I/O Pin No.
PAGE 420
Appendices Apx.C Pin Assignments Table C-12 Pin No. C-16 Docking I/F connector pin assignments (242-pin) (2/4) Signal name I/O Pin No.
PAGE 421
Apx.C Pin Assignments Table C-12 Pin No. Appendices Docking I/F connector pin assignments (242-pin) (3/4) Signal name I/O Pin No.
PAGE 422
Appendices Apx.C Pin Assignments Table C-12 Pin No. C-18 Docking I/F connector pin assignments (242-pin) (4/4) Signal name I/O Pin No.
PAGE 423
Apx.C Pin Assignments C.13 Appendices PJ2015 Mini PCI Card I/F Connector (124-pin) Table C-13 Mini PCI card I/F connector pin assignments (124-pin) (1/2) Pin No. Signal name I/O Pin No.
PAGE 424
Appendices Apx.C Pin Assignments Table C-13 Pin No. C-20 Mini PCI I/F card connector pin assignments (124-pin) (2/2) Signal name I/O Pin No.
PAGE 425
Apx.C Pin Assignments C.14 Appendices PJ2017 MDC I/F Connector (30-pin) Table C-14 MDC I/F connector pin assignments (30-pin) Pin No. Signal name I/O Pin No.
PAGE 426
Appendices C.16 Apx.C Pin Assignments PJ2020 Parallel I/F Connector (25-pin) Table C-16 Parallel I/F connector pin assignments (25-pin) Pin No. Signal name I/O Pin No.
PAGE 427
Apx.C Pin Assignments C.18 Appendices PJ2040 USB Board (FQDUB*) I/F Connector (30-pin) Table C-18 USB Board (FQDUB*) I/F connector pin assignments (30-pin) Pin No.
PAGE 428
Appendices C.20 Apx.C Pin Assignments PJ4900 Bluetooth I/F Connector (20-pin) Table C-20 Bluetooth I/F connector pin assignments (20-pin) Pin No. Signal name I/O Pin No. Signal name I/O 1 BT-P3V O 2 NC - 3 NC - 4 USBP5-S3N 5 USBP5-S3P I/O 6 NC - 7 NC - 8 -BTIFOF-S3N O 9 NC - 10 GND - 11 NC - 12 NC - 13 BTRST-S3P O 14 NC - I/O 15 NC - 16 NC - 17 NC - 18 BTMDL-P3N I 19 NC - 20 GND - C.
PAGE 429
Apx.C Pin Assignments C.23 Appendices PJ5006 Sound Board (FQDSD*) I/F Connector (60-pin) Table C-23 Sound board (FQDSD*) I/F connector pin assignments (60-pin) Pin No. Signal name I/O Pin No.
PAGE 430
Appendices C.24 Apx.C Pin Assignments PJ6100 IEEE 1394 I/F Connector (4-pin) Table C-24 IEEE 1394 I/F connector pin assignments (4-pin) Pin No. Signal name I/O Pin No. Signal name I/O 1 TPB0-P3N I/O 2 TPB0-P3P I/O 3 TPA0-P3N I/O 4 TPA0-P3P I/O C.25 PJ8770 Cooling fan I/F Connector (3-pin) Table C-25 Cooling fan I/F connector pin assignments (3-pin) Pin No. Signal name I/O Pin No. 2 1 P5V O 3 FANG-P3P I C.
PAGE 431
Apx.C Pin Assignments C.27 Appendices PJ8810 Battery I/F Connector (10-pin) Table C-27 Battery I/F connector pin assignments (10-pin) Pin No. Signal name I/O Pin No. Signal name 1 + 2 BTMP1 3 DCHG 4 M5V 5 PSCL-S5P 6 PSDA-S5P 7 GND - 8 DBT10V-S5N 9 GND - 10 GND C.28 I/O - PJ9999 RTC Battery I/F Connector (2-pin) Table C-28 RTC battery I/F connector pin assignments (2-pin) Pin No. 1 C.29 Signal name R3V I/O Pin No.
PAGE 432
Appendices Apx.C Pin Assignments VGA Board (FQDVG*) C.30 PJ4205 LCD I/F Connector (40-pin) Table C-30 LCD I/F connector pin assignments (40-pin) Pin No. C-28 Signal name I/O Pin No.
PAGE 433
Apx.C Pin Assignments C.31 Appendices PJ5500 System Board (FQDSY*) I/F Connector (200-pin) Table C-31 System board (FQDSY*) I/F connector pin assignments (200-pin) (1/3) Pin No. Signal name I/O Pin No.
PAGE 434
Appendices Apx.C Pin Assignments Table C-31 System board (FQDSY*) I/F connector pin assignments (200-pin) (2/3) Pin No. C-30 Signal name I/O Pin No.
PAGE 435
Apx.C Pin Assignments Appendices Table C-31 System board (FQDSY*) I/F connector pin assignments (200-pin) (3/3) Pin No. 137 Signal name NC I/O Pin No.
PAGE 436
Appendices Apx.C Pin Assignments Sound Board (FQDSD*) C.32 PJ5000 External Microphone I/F Connector (6-pin) Table C-32 External microphone I/F connector pin assignments (6-pin) Pin No. Signal name I/O Pin No. Signal name I/O 1 A-GND - 2 EMIC-PXP I 3 25VREF-P2V O 4 A-GND - 5 -EMICSL-P5P I 6 25VREF-P2V O C.33 PJ5002 Internal Microphone I/F Connector (2-pin) Table C-33 Internal microphone I/F connector pin assignments (2-pin) Pin No. 1 C.34 Signal name IMIC-PXP I/O Pin No.
PAGE 437
Apx.C Pin Assignments C.35 Appendices PJ5007 System Board (FQDSY*) I/F Connector (60-pin) Table C-35 System board (FQDSY*) I/F connector pin assignments (60-pin) Pin No. Signal name I/O Pin No.
PAGE 438
Appendices Apx.C Pin Assignments USB Board (FQDUB*) C.36 PJ2033 USB I/F Connector (8-pin) Table C-36 USB I/F connector pin assignments (8-pin) Pin No. Signal name A1 USB0PS-E5V A3 USBP0-S3P B1 USB0PS-E5V B3 USBP1-S3P C.37 I/O Pin No. Signal name - A2 USBP0-S3N I/O A4 GND - B2 USBP1-S3N I/O B4 GND I/O I/O I/O - PJ2042 System Board (FQDSY*) I/F Connector (30-pin) Table C-37 System Board (FQDSY*) I/F connector pin assignments (30-pin) Pin No.
PAGE 439
Appendix D Keyboard Scan/Character Codes Appendix D Appendix D Keyboard Scan/Character Codes Table D-1 Scan codes (set 1 and set 2) (1/4) Cap No.
PAGE 440
Appendix D Keyboard Scan/Character Codes Table D-1 Scan codes (set 1 and set 2) (2/4) D-2 Cap No.
PAGE 441
Appendix D Keyboard Scan/Character Codes Table D-1 Scan codes (set 1 and set 2) (3/4) Cap No.
PAGE 442
Appendix D Keyboard Scan/Character Codes Table D-1 Scan codes (set 1 and set 2) (4/4) Cap No. Keytop Code set 1 122 F11 57 D7 78 F0 78 *3 123 F12 58 D8 07 F0 07 *3 124 PrintSc *6 *6 *6 *6 *6 126 Pause *7 *7 *7 *7 *7 202 Fn — — — — *4 203 Win E0 5B E0 DB E0 1F E0 F0 1F 204 App E0 5D E0 DD E0 2F E0 F0 2F Make Code set 2 Break Make Note Break Notes: 1. 2. 3. 4. 5. 6. 7. D-4 * Scan codes differ by mode.
PAGE 443
Appendix D Keyboard Scan/Character Codes Table D-2 Scan codes with left Shift key Cap Key Code set 1 No.
PAGE 444
Appendix D Keyboard Scan/Character Codes Table D-3 Scan codes in Numlock mode Cap Key Code set 1 No.
PAGE 445
Appendix D Keyboard Scan/Character Codes Table D-5 Scan codes in overlay mode Cap No.
PAGE 446
Appendix D Keyboard Scan/Character Codes Table D-7 No.126 key scan code Key top Shift Code set 1 Code set 2 Make Make Pause Common * E1 1D 45 E1 Ctrl* E0 46 E0 C6 9D C5 E1 14 77 E1 F0 E0 7E E0 F0 7E 14 F0 77 *: This key generates only make codes.
PAGE 447
Appendix E Key Layout Appendix E Appendix E E.1 Key Layout United States (US) Keyboard Figure E-1 US keyboard E.
PAGE 448
Appendix E Key Layout E.3 German (GR) Keyboard Figure E-3 GR keyboard E.
PAGE 449
Appendix E Key Layout E.5 Spanish (SP) Keyboard Figure E-5 SP keyboard E.
PAGE 450
Appendix E Key Layout E.7 Scandinavian (SC) Keyboard Figure E-7 SC keyboard E.
PAGE 451
Appendix E Key Layout E.
PAGE 452
Appendix E Key Layout E-6 Satellite Pro M10 Series Maintenance Manual (960-431)
PAGE 453
Appendix F Wiring Diagrams Appendix F Appendix F F.1 Wiring Diagrams Parallel Port Wraparound Connector Figure F-1 Parallel port wraparound connector F.
PAGE 454
Appendix F Wiring Diagrams F.3 Serial Port Direct Cable (9-Pin to 9-Pin) Figure F-3 Serial port direct cable (9-pin to 9-pin) F.
PAGE 455
Appendix G BIOS Rewrite Procedures Appendix G Appendix G BIOS Rewrite Procedures This Appendix explains how to rewrite the system BIOS program when you update the system BIOS. Tools To rewrite the BIOS, you need the following tool: BIOS/EC/KBC rewriting disk for the computer that has renewed BIOS data. Rewriting the BIOS 1. Set the system to boot mode. 2. Turn off the power to the computer. 3. Remove the external cable and PC card. 4. Insert the BIOS/EC/KBC rewriting disk into the internal FDD. 5.
PAGE 456
Appendix G BIOS Rewrite Procedures G-2 Satellite Pro M10 Series Maintenance Manual (960-431)
PAGE 457
Appendix H EC/KBC Rewrite Procedures Appendix H Appendix H EC/KBC Rewrite Procedures This Appendix explains how to rewrite the EC/KBC system program when you update the EC/KBC system. Tools To rewrite the EC/KBC, you need the following tool: BIOS/EC/KBC rewriting disk for the computer Rewriting the EC/KBC NOTE: 1. Rewrite the EC/KBC only when instructed by a diagnostic disk release notice. 2. Connect the AC adaptor to the computer when you rewrite the EC/KBC. 3.
PAGE 458
Appendix H EC/KBC Rewrite Procedures H-2 Satellite Pro M10 Series Maintenance Manual (960-431)
PAGE 459
Appendix I Reliability Appendix I Appendix I Reliability The following table shows MTBF (Mean Time Between Failures) for each component.
PAGE 460
Appendix I Reliability I-2 Satellite Pro M10 Series Maintenance Manual (960-431)