TECRA M2 User’s Manual Tecra M2 TOSHIBA M2 Portable Personal Computer User’s Manual M2 TECRA M2 TECRA M2 TECRA M2 TECRA M2 TECRA M2 Choose freedom. computers.toshiba-europe.
Copyright © 2004 by TOSHIBA Corporation. All rights reserved. Under the copyright laws, this manual cannot be reproduced in any form without the prior written permission of TOSHIBA. No patent liability is assumed, with respect to the use of the information contained herein.
EU Declaration of Conformity This product is carrying the CE-Mark in accordance with the related European Directives. Responsible for CE-Marking is TOSHIBA Europe GmbH, Hammfelddamm 8, 41460 Neuss, Germany. The complete and official EU Declaration of Conformity can be found on TOSHIBA’s web site http://epps.toshiba-teg.com on the Internet.
Description on Laser specification The optical drive such as DVD-ROM drive, DVD/CD-RW drive, DVD Multi drive and DVD±R/±RW drive that is used in this computer is equipped with laser. The classification label with the following sentence is affixed to the surface of the drive.
General Precautions TOSHIBA computers are designed to optimize safety, minimize strain and withstand the rigors of portability. However, certain precautions should be observed to further reduce the risk of personal injury or damage to the computer. Be certain to read the general precautions below and to note the cautions included in the text of the manual. Stress injury Carefully read the Safety Instruction Manual.
Central Processing Unit ("CPU") Performance Disclaimer CPU Performance in your computer product may vary from specifications under the following conditions: ■ use of certain peripheral products ■ use of battery power instead of AC power ■ use of certain multimedia games or videos with special effects ■ use of standard telephone lines or low speed network connections ■ use of complex modeling software, such as high end computer aided design application ■ use of computer in areas with low air pressure (high a
Working environment This product was designed to fulfil the EMC (electromagnetic compatibility) requirements to be observed for so-called “Residential, commercial and light industry environments”. TOSHIBA do not approve the use of this product in working environments other than the above mentioned “Residential, commercial and light industry environments”.
Information on the secure use of the CD-RW Please adhere to the following information on the use of the CD-RW to minimise the risk of unsuccessful storing process. As the storing may be unsuccessful despite your adhering to these information, for example because of a defective storing medium, you should even if the software indicates a successful storage, always check if the data has been stored successfully.
Safety Instruction for Wireless Products If your computer has wireless function, all safety instructions must be read carefully and must be fully understood, before attempting to use our Wireless Products. This manual contains the safety instructions that must be observed in order to avoid potential hazards that could result in personal injuries or could damage your Wireless Products.
WARNING Turn OFF the Wireless Communication switch of Wireless Products in a congested place, such as a crowded commuter train. Keep this product away from a cardiac pacemaker at least 22cm. Radio waves can potentially affect cardiac pacemaker operation, thereby causing respiratory troubles. Turn OFF the Wireless Communication switch inside a medical facility or near medical electric equipment. Do not bring medical electric equipment close to the product.
TECRA M2 Table of Contents General Precautions Preface Manual contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . xvi Conventions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . xvii Chapter 1: Introduction Equipment checklist. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-1 Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-3 Special features . . . . . . . . . . . . . .
Table of Contents Chapter 3: Getting Started Setting up your work space . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-1 Connecting the AC adaptor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-4 Opening the display . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-5 Turning on the power . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-6 Windows XP setup. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Table of Contents Chapter 6: Power and Power-Up Modes Power conditions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-1 Power indicators . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-4 Battery types . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-5 Care and use of the battery pack . . . . . . . . . . . . . . . . . . . . . . . . 6-7 Replacing the battery pack . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Table of Contents Appendix A: Specifications Appendix B: AC Power Cord and Connectors Appendix C: Display Controller and Modes Appendix D: If your computer is stolen Appendix E: ASCII Character Codes Appendix F: Wireless LAN Appendix G: Internal Modem Guide Glossary Index TECRA M2 xiv
TECRA M2 Preface Congratulations on your purchase of the TECRA M2 computer. This powerful notebook computer provides excellent expansion capability, including multimedia devices, and it is designed to provide years of reliable, high-performance computing. This manual tells how to set up and begin using your TECRA M2 computer. It also provides detailed information on configuring your computer, basic operations and care, using optional devices and troubleshooting.
Preface Manual contents This manual is composed of the following nine chapters, seven appendixes, a glossary and an index. Chapter 1, Introduction, is an overview of the computer’s features, capabilities, and options. Chapter 2, The Grand Tour, identifies the components of the computer and briefly explains how they function. Chapter 3, Getting Started, provides a quick overview of how to begin operating your computer and gives tips on safety and designing your work area.
Preface Conventions This manual uses the following formats to describe, identify, and highlight terms and operating procedures. Abbreviations On first appearance, and whenever necessary for clarity, abbreviations are enclosed in parentheses following their definition. For example: Read Only Memory (ROM). Acronyms are also defined in the Glossary. Icons Icons identify ports, dials, and other parts of your computer.
Preface Messages Messages are used in this manual to bring important information to your attention. Each type of message is identified as shown below. Pay attention! A caution informs you that improper use of equipment or failure to follow instructions may cause data loss or damage your equipment. Please read. A note is a hint or advice that helps you make best use of your equipment.
TECRA M2 Chapter 1 Introduction This chapter provides an equipment checklist, and it identifies the computer’s features, options and accessories. Some of the features described in this manual may not function properly if you use an operating system that was not preinstalled by TOSHIBA. Equipment checklist Carefully unpack your computer. Save the box and packing materials for future use.
Introduction Software ■ The following software is preinstalled: ■ Microsoft® Windows XP Professional ■ Microsoft Internet Explorer ■ Modem driver ■ Display Driver for Windows ■ TOSHIBA Utilities ■ Wireless LAN driver ■ Bluetooth driver ■ TOSHIBA SD Memory Boot Utility ■ Sound Driver for Windows ■ DVD Video Player ■ LAN Driver ■ Infrared Device Driver ■ TOSHIBA Dual Pointing Device utility ■ TOSHIBA Power Saver ■ TOSHIBA Mobile Extension ■ TOSHIBA Console ■ TOSHIBA ConfigFree ■ TOSHIBA Zooming Utility ■ TOS
Introduction Features The computer uses TOSHIBA’s advanced Large Scale Integration (LSI), Complementary Metal-Oxide Semiconductor (CMOS) technology extensively to provide compact size, minimum weight, low power usage, and high reliability. This computer incorporates the following features and benefits: Processor Built-in The computer is equipped with an Intel® processor, which incorporates a math coprocessor, a 32 KB level 1 cache memory and a 1MB level 2 cache memory.
Introduction AC adaptor The universal AC adaptor provides power to the system and recharges the batteries when they are low. It comes with a detachable power cord. Because it is universal, it can receive a range of AC voltage from 100 to 240 volts; however, the output current varies among different models. Using the wrong model can damage your computer. See the AC adaptor section in Chapter 2, The Grand Tour. Disks Hard disk drive Available in four sizes. ■ 30.0 billion bytes (27.94 GB) ■ 40.
Introduction TECRA M2 CD-RW/DVD-ROM drive Some models are equipped with a full-size, CD-RW/DVD-ROM drive module that lets you run CD/DVDs without using an adaptor. It reads DVDROMs at maximum 8 speed and CD-ROMs at maximum 24 speed. It writes CD-R at up to 24 speed and CD-RW at up to 24 speed. For reading, this drive supports the same formats as the DVDROM drive.
Introduction DVD±R/±RW drive (DVD Dual drive) Some models are equipped with a full- size DVD±R/±RW drive module that lets you record data to rewritable CD/DVDs as well as run either 12cm (4.72") or 8cm (3.15") CD/DVDs without using an adaptor. It reads DVD-ROMs at maximum 8 speed and CD-ROMs at maximum 24 speed. It writes CD-R at up to 16 speed, CD-RW at up to 10 speed, DVD-R and DVD-RW at maximum 2 speed. DVD+R and DVD+RW at maximum 2.4 speed. This drive supports the same formats as the DVD-ROM drive.
Introduction TOSHIBA Dual Pointing Device Built-in Touch pad A Touch pad and control buttons in the palm rest enable control of the on-screen pointer and scrolling of windows. Built-in AccuPoint This pointer control stick, located in the center of the keyboard, provides convenient control of the cursor. Ports Parallel Parallel printer or other parallel device (ECP compatible). External monitor 15-pin, analog VGA port supports VESA DDC2B compatible functions. Universal Serial Bus (USB 2.
Introduction Multimedia Sound system Windows sound system compatible sound system provides internal speakers and microphone as well as jacks for an external microphone and headphone. Video-out jack (S-Video) This jack lets you transfer video data to external devices. Use an S-Video cable. Data output depends on the type of device connected to the S-Video cable. Headphone jack This jack outputs analog audio signals. Microphone jack A 3.
Introduction TECRA M2 Wireless LAN Some computers in this series are equipped with a Wireless LAN mini-PCI card that is compatible with other LAN systems based on Direct Sequence Spread Spectrum / Orthogonal Frequency Division Multiplexing radio technology that complies with the IEEE 802.11 Standard (Revision A, B or G), and Turbo Mode. ■ Automatic Transmit Rate Select mechanism in the transmit range of 54, 48, 36, 24, 18, 12, 9 and 6 Mbit/s.
Introduction Security Security lock slot Connects an optional security lock to anchor the computer to a desk or other large object. Slim Select Bay lock Slim Select Bay module can be secured by Slim Select Bay lock fixed with a lock screw in the lock position. The lock screw is inserted in the unlock position when purchased. Software Operating System Windows XP Professional operating system and TOSHIBA Utilities and drivers preinstalled on the hard disk.
Introduction HDD automatic power off This feature automatically cuts off power to the hard disk drive when it is not accessed for a time specified. Power is restored when the hard disk is accessed. You can specify the time in the HDD power off item of the Basic Setup tab in TOSHIBA Power Saver. System automatic This feature automatically shuts down the system Standby/Hibernation in standby mode or Hibernation mode when there is no input or hardware access for a time specified.
Introduction Heat dispersal To protect from overheating, the CPU has an internal temperature sensor. If the computer’s internal temperature rises to a certain level, the cooling fan is turned on or the processing speed is lowered. Use the Fan item of the Basic Setup tab in TOSHIBA Power Saver. ■ Maximum Performance ■ Performance ■ Battery optimized TECRA M2 Turns on fan first, then if necessary lowers CPU processing speed. Uses a combination of fan and lowering the CPU processing speed.
Introduction Utilities This section describes preinstalled utilities and tells how to start them. For details on operations, refer to each utility’s online manual, help files or readme.txt files. TOSHIBA Power Saver To access this power savings management program, click the Control Panel and select the TOSHIBA Power Saver icon. HW Setup This program lets you customize your hardware settings according to the way you work with your computer and the peripherals you use.
Introduction Drag’n Drop CD+DVD This easy-to-use software lets you record CD/ DVDs with just a few mouse clicks. You can create CD/DVDs in several formats including audio CDs that can be played on a standard stereo CD player and data CDs to store the files and folders on your hard drive. This software can be used on a model with CD-RW/DVD-ROM drive, DVD Multi drive and DVD±R/±RW drive. TOSHIBA Console TOSHIBA Console is a graphical user interface that provides easy access to help and services.
Introduction TOSHIBA Audio Effect This utility provides you with a hands-free environment for holding mutual communication via the Internet Protocol or Local Area Network. Refer to the Sound system section in Chapter 4, Operating Basics, for details. Options You can add a number of options to make your computer even more powerful and convenient to use.
Introduction Advanced Port Replicator III The Advanced Port Replicator III provides the ports available on the computer in addition to separate PS/2 mouse and PS/2 keyboard ports, a digital visual interface (DVI) port, i.LINK™ (IEEE1394) port, line-in jack and line-out jack, External moniter port, Universal Sirial Bus port (USB2.0) × 4, LAN jack, Modem jack. Hard disk drive You can increase your computer's data storage capacity with additional hard disk drives.
Introduction Slim Select Bay 2nd battery pack TECRA M2 The secondary battery increases your computer’s battery power and operating time when a main battery is also installed.
TECRA M2 Chapter 2 The Grand Tour This chapter identifies the various components of your computer. Become familiar with each component before you operate the computer. Front with the display closed The figure below shows the computer’s front with its display panel in the closed position.
The Grand Tour Off On Wireless communication switch Slide this switch to the left to turn off Wireless LAN and Bluetooth functions. Slide it to the right to turn on the functions (Wireless model or Wireless LAN ready model only). Left side The figure below shows the computer’s left side. COOLING VENTS i.
The Grand Tour 1 PC card slot A PC card slot can accommodate two 5 mm Type II cards or one Type III card. The slot supports 16-bit PC cards and CardBus PC cards. 0 CB Keep foreign objects out of the PC card slot. A pin or similar object can damage the computer’s circuitry. Security lock A security cable attaches to this slot. The optional security cable anchors your computer to a desk or other large object to deter theft. Right side The figure below shows the computer’s right side.
The Grand Tour External monitor port This 15-pin port lets you connect an external video display. Universal Serial Bus (USB 2.0) ports The ports comply with the USB 2.0 standard, which enables data transfer speeds 40 times faster than the USB 1.1 standard (The ports also support USB 1.1.). Keep foreign objects out of the USB connectors. A pin or similar object can damage the computer’s circuitry. Operation of all functions of all USB devices has not been confirmed.
The Grand Tour Backside The figure below shows the computer’s back panel. DC IN 15V VIDEO-OUT JACK MODEM JACK LAN ACTIVE INDICATOR (ORANGE) LINK INDICATOR (GREEN) LAN JACK The backside of the computer Video-out jack Plug an S-Video cable into this jack for video-out. The S-Video cable carries video signal. Modem jack In areas where an internal modem is installed as standard equipment, there is a modem jack that lets you use a modular cable to connect the modem directly to a telephone line.
The Grand Tour Underside The figure below shows the underside of the computer. Make sure the display is closed before turning over your computer. BATTERY LOCK BATTERY PACK NOTCHES BATTERY RELEASE LATCH SLIM SELECT BAY LATCH DOCKING INTERFACE SLIM SELECT BAY LOCK SCREW MEMORY MODULE COVER SLIM SELECT BAY HDD PACK COVER SCREW The underside of the computer TECRA M2 Battery lock Slide this lock to release the battery pack for removal.
The Grand Tour Keep foreign objects out of the docking interface port. A pin or similar object can damage the computer's circuitry. A plastic shutter protects the connector. Memory module cover This cover protects one of the memory module sockets. One or no module is preinstalled. Another memory module is under the keyboard. Refer to the Memory expansion section in Chapter 8, Optional Devices. Slim Select Bay lock Slide the lock to release or secure the Slim Select Bay ejector. .
The Grand Tour Front with the display open This section shows the computer with the display open. Refer to the appropriate illustration for details.
The Grand Tour TECRA M2 Touch pad control buttons Control buttons below the Touch Pad let you select menu items or manipulate text and graphics designated by the on-screen pointer. Touch pad A Touch pad located in the center of the palm rest is used to control the on-screen pointer. Refer to the Using the Touch pad section in Chapter 4, Operating Basics.
The Grand Tour Power button Press the power button to turn the computer’s power on and off. LCD Sensor switch This switch senses when the LCD panel is closed or opened and activates the Panel Power Off/On feature. When you close the panel the computer enters Hibernation mode and shuts down. When you open the panel the computer starts in Hibernation mode. Use the TOSHIBA Power Saver Utility to enable or disable this feature. The default is “enabled”.
The Grand Tour System indicators LEDs next to icons light when various computer operations are in progress. SD card DC IN 15V Power Battery Disk Slim Select Wireless comBay munication System indicators TECRA M2 SD card The SD card indicator glows blue when the computer is accessing the SD card slot. DC IN 15V The DC IN 15V indicator glows in green when DC power is supplied from the AC power adaptor.
The Grand Tour Wireless commnication The Wireless communication indicator glows when the Bluetooth and wireless LAN functions are turned on. Some models are equipped with a Wireless communication indicator. Keyboard indicators The figures below show the positions of the keypad overlay indicators and the Caps Lock indicator. When the F10 key indicator glows the keypad overlay lets you control the cursor. When the F11 key indicator glows the keypad overlay lets you enter numbers.
The Grand Tour Caps Lock This indicator glows green when the alphabet keys are locked in uppercase. Arrow mode When the Arrow mode indicator lights green, you can use the keypad overlay (gray labeled keys) as cursor keys. Refer to the Keypad overlay section in Chapter 5, The Keyboard. Numeric mode You can use the keypad overlay (gray labeled keys) for numeric input when the Numeric mode indicator lights green. Refer to the Keypad overlay section in Chapter 5, The Keyboard.
The Grand Tour ■ The external floppy disk drive should be placed on a flat, horizontal surface when in use. Do not set the drive on an incline greater than 20° while it is operating. ■ Do not set anything on top of the floppy disk drive. Optical media drives One of the following optical media drives is installed in the computer: DVDROM, CD-RW/DVD-ROM, DVD Multi and DVD±R/±RW drives. An ATAPI interface controller is used for CD/DVD-ROM operation.
The Grand Tour DVDs ■ DVD-R discs can be written only once. The recorded data cannot be erased orchanged. ■ DVD-RW discs can be recorded more than once. ■ DVD-RAM discs can be recorded more than once.
The Grand Tour DVD Multi drive The full-size DVD Multi drive module lets you record data to rewritable CD/ DVDs as well as run either 12 cm (4.72") or 8 cm (3.15") CD/DVDs without using an adaptor. The read speed is slower at the center of a disc and faster at the outer edge.
The Grand Tour AC adaptor The AC adaptor converts AC power to DC power and reduces the voltage supplied to the computer. It can automatically adjust to any voltage from 100 to 240 volts and to a frequency of either 50 or 60 hertz, enabling you to use the computer in almost any country/region. To recharge the battery, simply connect the AC adaptor to a power source and the computer. See Chapter 6, Power and Power-Up Modes, for details.
TECRA M2 Chapter 3 Getting Started This chapter provides basic information to get you started using your computer. It covers the following topics: ■ Setting up your work space — for your health and safety Be sure also to read the Safety Instruction Manual. This guide, which is included with the computer, explains product liability.
Getting Started General conditions In general, if you are comfortable, so is your computer, but read the following to make sure your work site provides a proper environment. ■ Make sure there is adequate space around the computer for proper ventilation. ■ Make sure the AC power cord connects to an outlet that is close to the computer and easily accessible. ■ The temperature should be 5 to 35 degrees Centigrade (41 to 95 degrees Fahrenheit) and the relative humidity should be 20 to 80 percent.
Getting Started Seating and posture The height of your chair in relation to the computer and keyboard as well as the support it gives your body are primary factors in reducing work strain. Refer to the following tips and to figure below. BELOW EYE LEVEL 90°ANGLES FOOT REST Posture and positioning of the computer ■ Place your chair so that the keyboard is at or slightly below the level of your elbow. You should be able to type comfortably with your shoulders relaxed.
Getting Started Work habits A key to avoiding discomfort or injury from repetitive strain is to vary your activities. If possible, schedule a variety of tasks into your workday. If you must spend long periods at the computer, finding ways to break up the routine can reduce stress and improve your efficiency. ■ Sit in a relaxed posture. Good positioning of your chair and equipment as described earlier can reduce tension in your shoulders or neck and ease back strain. ■ Vary your posture frequently.
Getting Started ■ Use only the AC adaptor supplied with your computer or an equivalent adaptor that is compatible. Use of any incompatible adaptor could damage your computer. TOSHIBA assumes no liability for any damage caused by use of an incompatible adaptor. ■ When you connect the AC adaptor to the computer, always follow the steps in the exact order as described in the User’s Manual.
Getting Started Use reasonable care when opening and closing the display panel. Opening it vigorously or slamming it shut could damage the computer. DISPLAY LATCH Opening the display Turning on the power This section describes how to turn on the power. After you turn on the power for the first time, do not turn it off until you have set up the operating system. Refer to the section Windows XP setup. 1. If an external floppy disk drive is connected, make sure it is empty.
Getting Started Windows XP setup When you first turn on the power, the computer’s initial screen is the Microsoft Windows XP Professional Startup Screen Logo. Follow the on-screen directions. Turning off the power The power can be turned off in one of the following modes: Shut down (Boot), Hibernation or Standby mode. Shut Down mode (Boot mode) When you turn off the power in Shut Down mode no data is saved and the computer will boot to the operating system’s main screen. 1.
Getting Started For the computer to shut down in hibernation mode, the hibernation feature must be enabled in two places : the Hibernate tab in Power Options and Setup Action tab in TOSHIBA Power Saver. Otherwise, the computer will shut down in Standby mode. If battery power becomes depleted, data saved in Standby mode will be lost. ■ You can return to your previous working environment immediately when you turn on the computer.
Getting Started Do not turn the computer or devices back on immediately. Wait a moment to let all capacitors fully discharge. Standby mode If you have to interrupt your work, you can turn off the power without exiting from your software. Data is maintained in the computer’s main memory. When you turn on the power again, you can continue working right where you left off. ■ When the AC adaptor is connected, the computer will go into Standby mode according to the settings in the TOSHIBA Power Saver utility.
Getting Started Executing standby You can also enable Standby by pressing Fn + F3. See Chapter 5, The Keyboard, for details. You can enter standby mode in one of three ways: 1. Click Start, click Turn Off Computer and click Stand by. 2. Close the display panel. This feature must be enabled. Refer to the Setup Action tab in TOSHIBA Power Saver Utility described in the Control Panel. Open Performance and Maintenance and open TOSHIBA Power Saver. 3. Slide the power button. This feature must be enabled.
Getting Started Restoring the preinstalled software If preinstalled files are damaged, use the Product Recovery disk or the TOSHIBA Tools & Utilities CD-ROM to restore them. Restoring the complete system To restore the operating system and all preinstalled software, follow the steps below. When you reinstall the Windows operating system, the hard disk will be reformatted and all data will be lost. Make sure you have a backup copy of your data, before you perform a complete system recovery. 1.
TECRA M2 Chapter 4 Operating Basics This chapter gives information on basic operations including using the TOSHIBA Dual Pointing Devices, USB floppy disk drive, the sound system, the optical media drives, the internal modem, wireless communication, LAN, and changing Slim Select Bay modules. It also provides tips on caring for your computer, diskettes and CD/DVDs. TOSHIBA Dual Pointing Device The computer is equipped with a dual point system: a Touch pad and an AccuPoint pointing stick.
Operating Basics Using the Touch pad To use the Touch pad, simply touch and move your fingertip across it in the direction you want the on-screen pointer to go. Two buttons below the Touch pad are used like the buttons on a mouse pointer. Press the left button to select a menu item or to manipulate text or graphics designated by the pointer. Press the right button to display a menu or other function depending on the software you are using.
Operating Basics Replacing the cap The AccuPoint cap is an expendable item that should be replaced after prolonged use. 1. To remove the AccuPoint cap, firmly pinch the cap and pull it straight up. Removing the AccuPoint cap 2. Position a new cap on the peg and press it into place. The peg is square, so be careful to align the cap’s square hole with the peg. Using the USB floppy disk drive (optional) An optional 3 1/2" floppy disk drive connects to the computer’s USB port. It accommodates 1.
Operating Basics If you connect the floppy disk drive after turning on the computer, it will take about 10 seconds for the computer to recognize the drive. Do not disconnect and reconnect before 10 seconds has elapsed. Disconnecting 3 1/2" floppy disk drive When you have finished using the floppy disk drive, follow the procedures below to disconnect it: 1. Wait for the indicator light to go out to make sure all diskette activity has stopped.
Operating Basics 4. Make sure the screw in the Slim Select Bay lock is set in the hole for the unlock position. 5. Slide the Slim Select Bay latch to the unlock position. 6. Grasp the DVD-ROM drive and slide it out. The DVD-ROM drive and other Slim Select Bay modules can become hot with use. Be careful when removing the module. LOCK SCREW SILM SELECT BAY LATCH SILM SELECT BAY MODULE Removing the DVD-ROM drive Inserting a module Insert the Slim Select Bay HDD adaptor as described below. 1.
Operating Basics Using optical media drives The text and illustrations in this section refer primarily to the DVD-ROM drive. However, operation is the same for other optical drive in the Slim Select Bay. The full-size drive provides high-performance execution of CD/DVD-ROMbased programs. You can run either 12 cm (4.72") or 8 cm (3.15") CD/DVDs without an adaptor. An ATAPI interface controller is used for CD/DVD-ROM operation.
Operating Basics b. Pressing the eject button will not open the drawer when the DVD-ROM drive’s power is off. If the power is off, you can open the drawer by inserting a slender object (about 15 mm) such as a straightened paper clip into the eject hole just to the right of the eject button. Manual release with the eject hole 2. Pinch the drawer gently and pull until it is fully opened. Pulling the drawer open 3. Lay the CD/DVD, label side up, in the drawer.
Operating Basics When the drawer is fully opened, the edge of the computer will extend slightly over the CD/DVD tray. Therefore, you will need to turn the CD/DVD at an angle when you place it in the tray. After seating the CD/DVD, however, make sure it lies flat, as shown in figure above. ■ Do not touch the laser lens. Doing so could cause misalignment. ■ Do not keep foreign matter from entering the drive. Check the back edge of the tray to make sure it carries no debris before closing the drive. 4.
Operating Basics Removing discs To remove the CD/DVD, follow the steps below and refer to the next figure. Do not press the eject button while the computer is accessing the DVDROM drive. Wait for the Slim Select Bay indicator to go out before you open the drawer. Also, if the CD/DVD is spinning when you open the drawer, wait for it to stop before you remove it. 1. To pop the drawer partially open, press the eject button. Gently pull the drawer out until it is fully opened.
Operating Basics Writing CDs on CD-RW/DVD-ROM drive Depending on the type of drive installed, you may be able to write CDs. The CD-RW/DVD-ROM drive lets you write as well as read CD-ROMs. Observe the precautions in this section to ensure the best performance for writing CDs. For information on loading and unloading CDs refer to the Using optical media drive section. CD-R discs can be written to only once. CD-RW discs can be rewritten many times.
Operating Basics ■ Writing with software other than Drag'n Drop CD+DVD has not been confirmed. Therefore, operation with other software cannot be guaranteed. When writing or rewriting Note the following when you write or rewrite a CD-R or CD-RW. ■ Always copy data from the HDD to the CD. Do not use cut-and-paste. The original data will be lost if there is a write error. ■ Do not perform any of the following actions: ■ Change users in the Windows XP operating system.
Operating Basics Writing CD/DVDs on DVD±R/±RW drive (DVD Dual drive) You can use the DVD±R/±RW drive to write data to either CD-R/RW or DVD-R/-RW/+R/+RW discs. The following applications for writing are supplied on CD-ROM: Drag'n Drop CD+DVD, licensed by Easy Systems Japan Ltd., and DigiOn Inc., InterVideo WinDVD Creator 2 Platinum, which is a product of InterVideo, Inc.
Operating Basics Disclaimer (DVD±R/RW drive) TOSHIBA does not bear responsibility for the following: ■ Damage to any CD-R/RW or DVD-R/-RW/+R/+RW disc that may be caused by writing or rewriting with this product. ■ Any change or loss of the recorded contents of CD-R/RW or DVD-R/ -RW/+R/+RW disc that may be caused by writing or rewriting with this product, or for any business profit loss or business interruption that may be caused by the change or loss of the recorded contents.
Operating Basics ■ If the disc is poor in quality, dirty or damaged, writing or rewriting errors may occur. Be careful to check the disc for dirt or damage before you use it. ■ The actual number of rewrites to CD-RW, DVD-RW or DVD+RW is affected by the quality of the disc and the way it is used. ■ There are two types of DVD-R discs: authoring and general use discs. Do not use authoring discs. Only general use discs can be written to by a computer drive.
Operating Basics ■ Writing with software other than Drag'n Drop CD+DVD is not recommended. When writing or rewriting Please observe/consider the following when you write or rewrite to a CD-R/ -RW, DVD-R/-RW/-RAM or DVD+R/+RW disc. ■ Do not perform any of the following actions when writing or rewriting: ■ Change users in the Windows XP operating system. ■ Operate the computer for any other function, including using a mouse or Touch Pad or closing/opening the LCD panel.
Operating Basics ■ Drag'n Drop CD+DVD cannot record in packet format. ■ You might not be able to use the DISC backup function of Drag'n Drop CD+DVD to back up a DVD-R/-RW or DVD+R/+RW disc that was made with other software on a different DVD-R/-RW or DVD+R/+RW recorder. ■ If you add data to a DVD-R disc that you have already recorded to, you might not be able to read the added data under some circumstances. It cannot be read in 16-bit operating systems, such as Windows 98SE and Windows ME.
Operating Basics Video (DVD-R/-RW/-RAM) As for "InterVideo WinDVD Creator2 Platinum", only the model that can be written in to DVD is attached. Note the following limitations when you write video to DVD: ■ When installing, uninstalling or InterVideo WinDVD Creator 2 Platinum, the computer should be set to system administrator or equivalent privilege. ■ When Drag'n Drop or similar software is resident in the computer's memory, the DVD Multi drive locks.
Operating Basics Media care This section provides tips on protecting data stored on your CD/DVDs and diskettes. Handle your media with care. The following simple precautions will increase the lifetime of your media and protect the data stored on them: CD/DVDs 1. Store your CD/DVDs in the container they came in to protect them and keep them clean. 2. Do not bend the CD/DVD. 3. Do not write on, apply a sticker to, or otherwise mar the surface of the CD/DVD that contains data. 4.
Operating Basics Sound System Using the microphone Your computer has a built-in microphone that can be used to record monaural sounds into your applications. It can also be used to issue voice commands to applications that support such functions. Since your computer has a built-in microphone and speaker, “howling” may be heard under certain conditions. Howling occurs when sound from the speaker is picked up in the microphone and amplified back to the speaker, which amplifies it again to the microphone.
Operating Basics If the No Power Savings is selected, the audio controller always runs. If you want to a more effect for the power management, you can select another mode, the High Power Savings which can save the power than the Normal Power Savings. To select it, follow the steps below. 1. Clicked the Power Management tab. 2. Select the High Power Savings in the Power Mode pull-down list. 3. Input a time in Power Save Delay (Seconds).
Operating Basics Modem This section describes how to connect and disconnect the internal modem to and from a telephone jack. The internal modem does not support voice functions. All data and fax functions are supported. ■ In case of a lightning storm, unplug the modem cable from the telephone jack. ■ Do not connect the modem to a digital telephone line. A digital line will damage the modem.
Operating Basics Properties menu Click the icon with the secondary mouse button to display properties menu on the screen. Setting You can enable or disable the following settings: AutoRun Mode The Region Select utility starts automatically when you start up the operating system. Open the Dialing Properties dialog box after selecting region. The dialing properties dialog box will be displayed automatically after you select the region. Location list for region selection.
Operating Basics ■ In case of a lightning storm, unplug the modem cable from the telephone jack. ■ Do not connect the modem to a digital telephone line. A digital line will damage the modem. 1. Plug one end of the modular cable into the modem jack. 2. Plug the other end of the modular cable into a telephone jack. Connecting the internal modem Do not pull on the cable or move the computer while the cable is connected.
Operating Basics Wireless communications The computer’s wireless communication function supports both wireless LAN and Bluetooth devices. Wireless LAN The Wireless LAN is compatible with other LAN systems based on Direct Sequence Spread Spectrum /Orthogonal Frequency Division Multiplexing radio technology that complies with IEEE802.11 wireless LAN standard (Revision A, B or G) and Turbo Mode. ■ Automatic Transmit Rate Select mechanism in the transmit range of 54, 48, 36, 24, 18, 12, 9 and 6Mbit/s.
Operating Basics Bluetooth wireless technology Bluetooth™ wireless technology eliminates the need for cables between electronic devices such as desktop computers, printers and mobile phones. You cannot use the built-in Bluetooth functions and an optional Bluetooth SD card 2 simultaneously. Bluetooth wireless technology has the following features: Worldwide operation The Bluetooth radio transmitter and receiver operate in the 2.
Operating Basics Wireless communication Indicator The wireless communication indicator indicates the status of the wireless communication functions. Indicator status Indication Indicator off Wireless communication switch is set to off. Automatic power down because of overheating. Power malfunction Indicator glows Wireless communication switch is on. Wireless LAN or Bluetooth is turned on by an application.
Operating Basics LAN The computer has built-in support for Ethernet LAN (10 megabits per second, 10BASE-T), Fast Ethernet LAN (100 megabits per second, 100BASE-Tx) and Gigabit Ethernet LAN (1000 megabits per second, 1000BASE-T). Some models are equipped with a Gigabit Ethrnet LAN. This section describes how to connect/disconnect to a LAN. Do not install or remove an optional memory module while Wake-up on LAN is enabled. The Wake-up on LAN function consumes power even when the system is off.
Operating Basics 3. Plug the other end of the cable into a LAN hub connector. Check with your LAN administrator before connecting to a hub. When the computer is exchanging data with the LAN, the LAN Active indicator glows orange. When the computer is connected to a LAN hub but is not exchanging data, the Link indicator glows green. Disconnecting LAN cable To disconnect the LAN cable, follow the steps below.
Operating Basics Moving the computer The computer is designed for rugged durability. However, a few simple precautions taken when moving the computer will help ensure trouble-free operation. ■ Make sure all disk activity has ended before moving the computer. Check the Disk and Slim Select Bay indicators on the computer. ■ If a CD/DVD is in the drives, remove it. Also make sure the drawer is securely closed. ■ Turn off the power to the computer.
TECRA M2 Chapter 5 The Keyboard The computer’s keyboard layouts are compatible with a 101/102-key enhanced keyboard. By pressing some keys in combination, all the 101/ 102-key keyboard functions can be executed on the computer. The number of keys on your keyboard depends on which country/region’s keyboard layout your computer is configured with. Keyboards for numerous languages are available. There are five types of keys: typewriter keys, keypad overlay, function keys, soft keys and cursor control keys.
The Keyboard F1 … F12 function keys The function keys (not to be confused with Fn) are the 12 keys at the top of your keyboard. These keys function differently from other keys. F1 through F12 are called function keys because they execute programmed functions when pressed. Used in combination with the Fn key, keys marked with icons execute specific functions on the computer. See the section, Soft keys: Fn key combinations, in this chapter.
The Keyboard Press Fn + F10 or Fn + F11 to access the integrated keypad. When activated, the keys with gray markings on the bottom edge become numeric keypad keys (Fn + F11) or cursor control keys (Fn + F10). Refer to the Keypad overlay section in this chapter for more information on how to operate these keys. The power on default for both settings is off. Press Fn + F12 (ScrLock) to lock the cursor on a specific line. The power on default is off.
The Keyboard Hot keys Hot keys (Fn + a function or Esc key) let you enable or disable certain features of the computers. Sound mute: Pressing Fn + Esc in a Windows environment turns sound on or off. When you press these hot keys, the current setting will change and be displayed as an icon. Instant security: Press Fn + F1 to blank the screen to prevent others from accessing your data. To restore the screen and original settings, press any key or press the Dual Pointing Device.
The Keyboard Hibernation: When you press Fn + F4, the computer enters Hibernation. To avoid entering Hibernation unexpectedly, a dialog box appears for verification. However, if you select the check box, it will not appear in the future. Display selection: Press Fn + F5 to change the active display device. When you press these hot keys, a dialog box appears. Only selectable devices will be displayed. Hold down Fn and press F5 again to change the device.
The Keyboard Wireless setting: If your computer has both Bluetooth and wireless LAN functions, you can press Fn + F8 to select which type of wireless communication you want to use. When you press these hot keys, a dialog box will appear. Continue holding down Fn and press F8 to change the setting. If wireless communication is turned off, Disabled Wireless Communication Switch will be displayed. If no wireless communication device is installed, no dialog box will appear.
The Keyboard Windows special keys The keyboard provides two keys that have special functions in Windows : Windows logo key activates the start menu and the other, the application key, has the same function as the secondary mouse button. This key activates the Windows start menu. This key has the same function as the secondary mouse button. Keypad overlay Your computer’s keyboard does not have an independent numeric keypad, but its numeric keypad overlay functions like one.
The Keyboard The numeric keypad overlay Temporarily using normal keyboard (overlay on) While using the overlay, you can temporarily access the normal keyboard without turning off the overlay: 1. Hold Fn and press any other key. All keys will operate as if the overlay were off. 2. Type upper-case characters by holding Fn + Shift and pressing a character key. 3. Release Fn to continue using the overlay.
The Keyboard Generating ASCII characters Not all ASCII characters can be generated using normal keyboard operation. But, you can generate these characters using their ASCII codes. With the overlay on: 1. Hold down Alt. 2. Using the overlay keys, type the ASCII code. 3. Release Alt, and the ASCII character appears on the display screen. With the overlay off: 1. Hold down Alt + Fn. 2. Using the overlay keys, type the ASCII code. 3. Release Alt + Fn, and the ASCII character appears on the display screen.
TECRA M2 Chapter 6 Power and Power-Up Modes The computer’s power resources include the AC adaptor and internal batteries. This chapter gives details on making the most effective use of these resources including charging and changing batteries, tips for saving battery power, and power up modes.
Power and Power-Up Modes Power on AC adaptor connected AC adaptor not connected AC adaptor not connected TECRA M2 2nd battery fully • Operates charged • No charge • LED: 2nd Battery green DC IN 15V green Power off (no operation) • No charge • LED: 2nd battery green DC IN 15V green 2nd Battery partially charged or no charge • Operates • Quick charge*2 • Charge*2 • LED: 2nd battery orange • LED: 2nd battery orange DC IN 15V green DC IN 15V green No 2nd battery installed • Operates • No charge • LED:
Power and Power-Up Modes 2nd battery indicator refers to the Slim Select Bay indicator when a secondary battery is installed. *1 When the 2nd battery is not charging. *2 When the main battery is not charging. *3 For the computer to shut down in hibernation mode, the hibernation feature must be enabled in two places in TOSHIBA Power Saver: the Hibernate window and the Battery Alarm item of the Alarm window.
Power and Power-Up Modes Power indicators As shown in the above table, the Battery, Slim Select Bay, DC IN 15V and Power indicators on the system indicator alert you to the computer’s operating capability and battery charge status. Battery indicators Check the Battery indicator to determine the status of the main battery and the Slim Select Bay indicator to determine the status of the secondary battery. The following indicator lights indicate the battery status: Flashing orange The battery charge is low.
Power and Power-Up Modes Power indicator Check the Power indicator to determine the power status: Green Indicates power is being supplied to the computer and the computer is turned on. Blinking orange Indicates power is being supplied to the computer while the computer is in Standby mode. The indicator turns on for one second and off for two seconds. No light Under any other conditions, the indicator does not light.
Power and Power-Up Modes 2nd battery (option) An optional 2nd battery can be installed in the Slim Select Bay to increase your battery operating time. Note the caution on Standby mode in the previous section Main battery. The 2nd battery pack is a lithium ion battery, which can explode if not properly replaced, used, handled or disposed of. Dispose of the battery as required by local ordinances or regulations. Use only batteries recommended by TOSHIBA as replacements.
Power and Power-Up Modes Care and use of the battery pack The battery pack is a vital component of portable computing. Taking proper care of it will help ensure longer operating time on battery power as well as a longer life for your battery pack. Follow the instructions in this section carefully to ensure safe operation and maximum performance. Safety precautions Mishandling of batteries can cause death, serious injury or property damage.
Power and Power-Up Modes 8. Never expose the battery pack to abnormal shock, vibration or pressure. The battery pack’s internal protective device will fail, causing it to overheat, explode, ignite or leak caustic liquids possibly resulting in death or serious injury. 9. Never let a battery pack become wet. A wet battery pack will overheat, ignite or rupture possibly resulting in death or serious injury. Warning 1.
Power and Power-Up Modes 6. Be sure to monitor the remaining battery power. If the battery pack and real time clock battery discharge completely, Standby and Suspend will not function and data in memory will be lost. Also, the computer might register an incorrect time and date. In this case, connect the AC adaptor to recharge the batteries. 7. Never install or remove the battery pack without first turning off the power and disconnecting the AC adaptor.
Power and Power-Up Modes Time The following table shows the approximate time required to fully charge a discharged battery. Charging time (hours) Battery type Power on Power off High capacity battery pack (8800mAh) about 10.5 to 21.5 about 4.5 Main battery pack (4400mAh) about 5.0 to 11.0 about 2.5 2nd battery pack about 4.5 to 9.
Power and Power-Up Modes Monitoring battery capacity Remaining battery power can be monitored in TOSHIBA Power Saver. ■ Wait at least 16 seconds after turning on the computer before trying to monitor the remaining operating time. The computer needs this time to check the battery’s remaining capacity and to calculate the remaining operating time, based on the current power consumption rate and remaining battery capacity. The actual remaining operating time may differ slightly from the calculated time.
Power and Power-Up Modes Retaining data with power off When you turn off your computer with fully charged batteries, the batteries retain data for the following approximate time periods.
Power and Power-Up Modes Replacing the battery pack When the battery pack reaches the end of its operating life you will need to install a new one. The life of the battery pack is generally about 500 recharges. If the Battery indicator or Slim Select Bay indicator (if a Slim Select Bay 2nd battery pack is installed) flashes orange shortly after fully recharging the battery, the battery pack needs to be replaced.
Power and Power-Up Modes 5. Slide and hold the battery release latch to free the battery pack for removal after switching the battery safety lock into unlock position (in left direction), then slide out the battery pack. BATTERY PACK BATTERY LOCK BATTERY RELEASE LATCH Releasing the battery pack For environmental reasons, do not throw away a spent battery pack. Please return spent battery packs to your TOSHIBA dealer. Installing the battery pack To install a battery, follow the steps below.
Power and Power-Up Modes 4. Secure the battery pack lock. Switch the battery safety lock into lock position.
Power and Power-Up Modes TOSHIBA Password Utility The TOSHIBA Password Utility provides two levels of password security: User and Supervisor. Passwords set in TOSHIBA Password Utility are different from the Windows password. User password To start the utility, point to or click the following items: Start -> All Programs -> TOSHIBA -> Utilities -> Password Utility The user password dialog box contains two main fields: User Password and User Token.
Power and Power-Up Modes When you format an SD Memory card, all data will be deleted. Be sure to save data on the card to other media before you format the card. ■ Disable (button) Click this button to invalidate the token. You cannot revalidate old tokens, but you can use the same SD cards to create new tokens. Supervisor password If you set a supervisor password, some functions might be restricted when a user logs on with the user password. To set a supervisor password, execute the file TOSUP.EXE.
Power and Power-Up Modes Power-up modes The computer has the following power-up modes: ■ Boot: Computer shuts down without saving data. Always save your work before you turn the computer off in boot mode. ■ Hibernation: Data in memory is saved to the hard disk. ■ Standby: Data is maintained in the computer’s main memory. Refer also to the sections Turning on the power and Turning off the power in Chapter 3, Getting Started. Windows utilities You can specify the setting in TOSHIBA Power Saver.
TECRA M2 Chapter 7 HW Setup This chapter explains how to use the TOSHIBA HW Setup program to configure your computer. TOSHIBA HW Setup lets you configure settings for Display, CPU, Boot Priority, Keyboard, USB, LAN, General, Device Config and Parallel/Printer. Some models are not equipped with Parallel/Printer tab and/or CPU tab. Accessing HW Setup To run HW Setup, click start, click Control Panel, click Printers and Other Hardware and select TOSHIBA HW Setup.
HW Setup Setup This field displays BIOS Version and date. Device Config Device Configuration This option lets you set the device configuration. All Devices BIOS sets all devices. Setup by OS Operating system sets devices that it can control. (Default) Parallel/Printer Some models are equipped with Parallel/Printer tab. This tab lets you set the Parallel Port Mode. Use the Windows Device Manager to make settings for the Parallel port.
HW Setup CPU This function lets you set the CPU operating mode. Dynamic CPU Frequency Mode This option lets you choose from the following settings: TECRA M2 Dynamically Switchable CPU power consumption and clock speed automatic switching function is enabled. When the computer is in use, CPU operation is automatically switched when necessary. (Default) Always High CPU power consumption and clock speed automatic switching function is disabled. The CPU always runs at its fastest speed.
HW Setup Boot Priority Boot Priority Options This option sets the priority for booting the computer. Select from the following settings: HDD −> FDD −> CD-ROM −> LAN The computer looks for bootable files in the following order: HDD, floppy disk drive*1, CD-ROM*2 and LAN. (Default) FDD −> HDD −> CD-ROM −> LAN The computer looks for bootable files in the following order: floppy disk drive*1, HDD, CD-ROM*2 and LAN.
HW Setup ■ PC card HDD boot is supported only by slot 0 on the computer. Support is guaranteed only for TOSHIBA PC card HDDs. ■ When you assign a PC card HDD top priority, “PC” is not displayed. However, the PC card HDD takes the position of HDD in the Boot Priority Options list above. To change the boot drive, follow the steps below. 1. Hold down F12 and boot the computer. 2.
HW Setup HDD Priority Options If more than one HDD is installed in the computer, this option lets you set the priority for HDD detection. If the first detected HDD has a boot command, the system will boot from the HDD. Built-in HDD −> 2nd HDD −> PC Card(Default) The computer will look for the Built-in HDD first, next the 2nd HDD and then the PC Card (Default). 2nd HDD −> Builtin HDD −> PC Card The computer will look for the 2nd HDD first, next the Built-in HDD and then the PC Card.
HW Setup Keyboard External Keyboard Fn key Use this option to set a key combination on an external keyboard to emulate the Fn key on the computer’s internal keyboard. Setting an Fn key equivalent will let you use Hot keys by pressing the set combination instead of the Fn key.
HW Setup Built-in LAN This feature enables or disables the Built-in LAN. Enabled Enables Built-in LAN functions. (Default) Disabled Disables Built-in LAN functions. USB USB KB/Mouse Legacy Emulation Use this option to enable or disable USB KB/Mouse Legacy Emulation. If your operating system does not support USB, you can still use a USB mouse and keyboard by setting the USB KB/Mouse Legacy Emulation item to Enabled. Enabled Enables the USB KB/Mouse Legacy Emulation.
TECRA M2 Chapter 8 Optional Devices Optional devices can expand the computer’s capabilities and its versatility.
Optional Devices PC cards The computer is equipped with a PC card expansion slot that can accommodate one 5 mm Type II card. Any PC card that meets industry standards (manufactured by TOSHIBA or other vendor) can be installed. The slot supports 16-bit PC cards, including PC card 16’s multifunction card and CardBus PC cards. CardBus supports the new standard of 32-bit PC cards. The bus provides superior performance for the greater demands of multimedia data transmission.
Optional Devices Removing a PC card To remove the PC card, follow the steps below. 1. Open the Safety Remove Hardware icon on the system tray and disable the PC card. 2. Press the PC card eject button to extend it. 3. Press the extended eject button to pop the card out slightly. 4. Pinch the PC card and draw it out. PC CARD EJECT BUTTON Removing the PC card SD cards The computer is equipped with an SD card slot that can accommodate Secure Digital flash memory cards with various memory capacities.
Optional Devices Formatting an SD card SD memory cards are sold with format in conformity to the Standards of SD memory card. If you format the SD card again, be sure to format it with the utility of TOSHIBA SD memory card format, not in the format defined as the Windows standard format. In order to run TOSHIBA SD memory card format, click windows start button, point to All Programs, point to TOSHIBA, point to Utilities and click SD memory card Format.
Optional Devices 3. Grasp the card and remove it. SD CARD Removing an SD card ■ Make sure the SD card indicator is out before you remove the card or turn off the computer’s power. If you remove the card or turn off the power while the computer is accessing the card you may lose data or damage the card. ■ Do not remove an SD card while the computer is in Standby or Hibernation mode. The computer could become unstable or data in the SD card could be lost.
Optional Devices Memory expansion This computer is equipped with two memory module sockets; Slot A is beneath the keyboard and Slot B is on the underside of the computer. You can increase the amount of RAM to 2048 MB by installing an additional memory or replacing default memories with additional memories. ■ Observe the following instructions according to the model you purchased. a. Install an additional memory module to Slot B for the computer with vacant Slot B. b.
Optional Devices Be sure to install memory module to Slot A. The computer does not boot when Slot A is vacant. Use a 0-bit, Phillips screwdriver to remove and fasten screws. Use of an incorrect screwdriver can damage the screw heads. Installing memory module (Main memory) To install a memory module, make sure the computer is in boot mode then: 1. Turn the computer off in boot mode. Refer to the Turning off the power section in Chapter 3, Getting Started. 2. Remove all cables connected to the computer. 3.
Optional Devices Removing the keybord brace, removing two screws and rotate the keyboard Use a point size 0 Phillips screwdriver. 8. Lift up the back of the keyboard, rotate it toward you and lay in face down on the palm rest. ■ When you move the keyboard forward, do not touch the keys. Doing so could cause misalignment. Hold the keyboard by the sides and lay it gently on the palm rest. ■ The keyboard is connected to the computer by a ribbon cable.
Optional Devices Do not touch the connectors on the memory module or on the computer. Debris on the connectors may cause memory access problems. 10. Insert a new module in the socket and push it down so it lies flat and is secured by two latches on either side. Installing the memory module 11. The keyboard cable is pressed down with Metal brace and one screw secures the metal brace. 12. Insert tabs on the front of the keyboard into corresponding notches on the computer and seat the keyboard.
Optional Devices Removing memory module (Main memory) To remove the memory module, make sure the computer is in boot mode then: 1. Turn the computer off and remove all cables connected to the computer. 2. Turn the computer upside down and remove the battery pack (refer to Chapter 6, Power and Power-up Modes.) 3. Follow steps 4 through 9 in Installing memory module to access the memory module. 4. Push the latches to the outside to release the module. A spring will force one end of the module up. 5.
Optional Devices Installing memory module (2nd memory) Follow the steps below to install a memory module. 1. Save data, shutdown Windows and turn the power off. 2. Remove the AC adapter cable and other cables from the computer. 3. Close the display panel and turn the computer over. Remove the battery pack. 4. Loosen a screw on the cover of the memory module slot. Removing the memory module cover 5. Insert the memory module obliquely against the connector of the memory module slot.
Optional Devices Seating the memory module cover 7. Reinstall the battery pack. After installing a memory module, turn the power of the computer on to see a total memory size. The system will calculate the total memory size. Removing memory module (2nd memory) To remove the memory module, make sure the computer is in boot mode then: 1. Save data, shutdown Windows and turn the power off. 2. Remove the AC adapter cable and other cables from the computer. 3.
Optional Devices Hard disk drive pack An extra HDD expands the flexibility of your system and lets you carry your data without carrying the computer. Use a point size 0 Phillips screwdriver. Removing the HDD pack To remove the HDD pack, follow the steps below and refer to figures below. 1. Set the computer to boot mode and turn off the power. 2. Disconnect the AC adaptor and all external cables connected to the computer. 3. Remove the main battery and optional secondary battery when it is used. 4.
Optional Devices 8. Lift the HDD pack and remove it. Removing the HDD pack Installing the HDD pack To install the hard disk drive, follow the steps below. 1. Place the HDD into the space for HDD. Slide the HDD to connect to the connector. 2. Fold over the plastic tab so that it goes into the HDD space. Press the HDD to ensure a firm connection. Installing the HDD pack 3. Seat the cover and press down until the latches click into place. 4. Secure the cover with a screw.
Optional Devices Additional battery pack You can increase the portability of the computer with additional battery packs. If you’re away from an AC power source and your battery runs low, you can replace it with a freshly charged battery. See Chapter 6, Power and Power-Up Modes. High capacity battery pack You can increase the portability of the computer with a high capacity battery pack. See Chapter 6, Power and Power-Up Modes.
Optional Devices Removing the 2nd battery pack from the adaptor Additional AC adaptor If you frequently transport the computer between different sites such as your home and office, purchasing an AC adaptor for each location will reduce the weight and bulk of your carrying load. Battery charger The battery charger provides a convenient way to charge battery packs without requiring the use of your computer. The battery charger holds up to two lithium ion battery packs.
Optional Devices 2. Insert the HDD and push forward to ensure a firm connection. Inserting the HDD 3. Close the lid and slide the lock to the lock position. Closing the lid For details on inserting the Slim Select Bay HDD adaptor in the Slim Select Bay, refer to Chapter 4, Operating Basics. External monitor An external analog monitor can be connected to the external monitor port on the computer. The computer supports VGA and Super VGA video modes. To connect a monitor, follow the steps below. 1.
Optional Devices TV You can connect a television set to the Video out jack on the computer. Follow the steps below. Using the TOSHIBA Console button 1. Connect the TV adaptor cable’s S-Video plug to the Video out jack on the computer. 2. Connect the TV adaptor cable’s S-Video plug to the S-Video jack on the TV. 3. Press the TOSHIBA Console button. You can use the hot keys Fn + F5 to change the display device. Refer to Chapter 5, The Keyboard.
Optional Devices 4. Select the GeForce FX Go5200 30M/64M tab. a. Click the GeForce FX Go5200 32M/64M button. b. Click Overlay Controls in the small menu. c. From the Full Screen Device drop down menu, select Primary Device or Secondary Device to enable movie display on an external TV or CRT monitor. Primary Device: Movies will be displayed full screen on the computer‘s internal LCD and in a window on the TV or CRT monitor.
Optional Devices ■ If you connect/disconnect an i.LINK device to/from another i.LINK device that is currently exchanging data with the computer, data frames might be dropped. ■ Make sure data transfer has ended or turn off the computer, before you: ■ Connect/disconnect an i.LINK device to/from the computer. ■ Connect/disconnect an i.LINK device to/from another i.LINK device that is connected to the computer. Connecting 1. Make sure the connectors are properly aligned and plug the i.
Optional Devices Advanced Port Replicator IIl In addition to the ports available on the computer, the Advanced Port Replicator III provides a Serial port and separate ports for PS/2 mouse and PS/2 keyboard. The Port Replicator connects directly to the docking interface on the bottom of the computer. The AC adaptor connects the Port Replicator to a power source. The computer must be configured properly before connecting to a LAN.
Optional Devices Parallel printer You can connect any standard Centronics-compatible parallel printer to your computer. All you need is an IBM PC parallel printer cable. Your dealer can supply one or you can purchase one at most computer stores. The cable’s connectors are designed so that it is impossible for you to connect them incorrectly. You can also connect a parallel printer to an optional Advanced Port Replicator III. To connect a printer, follow these steps: 1. Turn off the computer. 2.
TECRA M2 Chapter 9 Troubleshooting TOSHIBA designed the computer for durability. However, should problems occur, following the procedures in this chapter can help to determine the cause. All readers should become familiar with this chapter. Knowing what might go wrong can help prevent problems from occurring. Problem solving process Resolving problems will be much easier if you observe the following guidelines: ■ Stop immediately when you recognize a problem exists.
Troubleshooting Preliminary checklist Consider the simplest solution first. The items in this checklist are easy to fix and yet can cause what appears to be a serious problem. ■ Make sure you turn on all peripheral devices before you turn on the computer. This includes your printer and any other external device you are using. ■ Before you attach an external device, turn the computer off. When you turn the computer back on it recognizes the new device.
Troubleshooting Software The problems may be caused by your software or disk. If you cannot load a software package, the media may be damaged or the program might be corrupted. Try loading another copy of the software. If an error message appears while you are using a software package, check the software documentation. These documents usually include a problem solving section or a summary of error messages. Next, check any error messages in the OS documentation.
Troubleshooting System start-up When the computer does not start properly, check the following items: ■ Self Test ■ Power Sources ■ Power-on Password Self test When the computer starts up, the self test will be run automatically, and the following will be displayed: In Touch with Tomorrow TOSHIBA This message remains on the screen for a few seconds. If the self test is successful, the computer tries to load the operating system, depending on how the Boot Priority is set in the TOSHIBA HW Setup program.
Troubleshooting It is recommended to leave the computer off until the its interior reaches room temperature even though the DC IN 15V indicator stops blinking. If the computer has reached room temperature and still does not start, or if it starts but shuts down quickly contact your dealer. Computer shuts down and its DC IN 15V indicator is flashing in green Indicates a problem with the heat dispersal system. Please contact your dealer.
Troubleshooting Problem Procedure Battery doesn’t charge when the AC adaptor is attached (Battery or Slim Select bay indicator does not glow in orange.) If the battery is completely discharged, it will not begin charging immediately. Wait a few minutes. If the battery still does not charge, make sure the outlet of the AC adaptor is supplying power. Test it by plugging in an appliance. Check whether the battery is hot or cold to the touch.
Troubleshooting Keyboard Keyboard problems can be caused by your setup configuration. For more information refer to Chapter 5, The Keyboard. Problem Procedure Some letter keys produce numbers Check that the numeric keypad overlay is not selected. Press Fn + F11 and try typing again. Output to screen is garbled Make sure the software you are using is not remapping the keyboard. Remapping involves reassigning the meaning of each key. See your software’s documentation.
Troubleshooting DVD-ROM drive For more information, refer to Chapter 4, Operating Basics TECRA M2 Problem Procedure You cannot access a CD/ DVD in the drive Make sure the drive’s drawer is securely closed. Press gently until it clicks into place. Open the drawer and make sure the CD/DVD is properly seated. It should lie flat with the label facing up. A foreign object in the drawer could block laser light from reading the CD/DVD. Make sure there is no obstruction. Remove any foreign object.
Troubleshooting CD-RW/DVD-ROM drive For more information, refer to Chapter 4, Operating Basics. TECRA M2 Problem Procedure You cannot access a CD/DVD in the drive Make sure the drive’s drawer is securely closed. Press gently until it clicks into place. Open the drawer and make sure the CD/DVD is properly seated. It should lie flat with the label facing up. A foreign object in the drawer could block laser light from reading the CD/DVD. Make sure there is no obstruction. Remove any foreign object.
Troubleshooting TECRA M2 Problem Procedure Cannot write correctly If you have trouble writing, make sure you are observing the following precautions: ■ Use only media recommended by TOSHIBA. ■ Do not use the mouse or keyboard during writing. ■ Use only the software supplied with the computer for recording. ■ Do not run or start other software during writing. ■ Do not jar the computer during writing. ■ Do not connect/ disconnect external devices or install/remove internal cards during writing.
Troubleshooting DVD Multi drive For more information, refer to Chapter 4, Operating Basics. TECRA M2 Problem Procedure You cannot access a CD/DVD in the drive Make sure the drive’s drawer is securely closed. Press gently until it clicks into place. Open the drawer and make sure the CD/DVD is properly seated. It should lie flat with the label facing up. A foreign object in the drawer could block laser light from reading the CD/DVD. Make sure there is no obstruction. Remove any foreign object.
Troubleshooting Problem Procedure Cannot write correctly If you have trouble writing, make sure you are observing the following precautions: ■ Use only media recommended by TOSHIBA. ■ Do not use the mouse or keyboard during writing. ■ Use only the software supplied with the computer for recording. ■ Do not run or start other software during writing. ■ Do not jar the computer during writing. ■ Do not connect/ disconnect external devices or install/remove internal cards during writing.
Troubleshooting Check the type of CD/DVD you are using. The drive supports: DVD-ROM: DVD-ROM, DVD-Video, DVD-R,DVDRW, DVD+R, DVD+RW CD-ROM: CD-DA, CD-Text, Photo CD (single/ multi-session), CD-ROM Mode 1, Mode 2, CD-ROM XA Mode 2 (Form1, Form2), Enhanced CD (CD-EXTRA), CD-G (Audio CD only), Addressing Method 2 Check the region code on the DVD. It must match that on the DVD±R/±RW drive. Region codes are listed in the Optical media section in Chapter 2, The Grand Tour.
Troubleshooting SD card Refer also to Chapter 8, Optional Devices. Problem Procedure SD card error occurs Reseat the SD card to make sure it is firmly connected. Check the card’s documentation. You cannot write to an SD card Make sure the card is not write protected. You cannot read a file Make sure the target file is on the SD Card inserted in the slot. If problems persist, contact your dealer. PC card Refer also to Chapter 8, Optional Devices.
Troubleshooting TOSHIBA Dual Pointing Device If you are using a USB mouse, also refer to the USB section in this chapter and to your mouse documentation. Touch pad/AccuPoint Problem Procedure Either the Touch pad or the AccuPoint does not work. Check the Device Select settings. Open the Mouse properties icon and click the Dual Point tab. Then click the Detail Setting button and click the Device Select tab. Check that the Touch pad is not selected.
Troubleshooting Problem Procedure Double-clicking does not work Try changing the double-click speed setting in the mouse control utility. 1. Open the Control Panel, select the Mouse icon and press Enter. 2. Click the Buttons tab. 3. Set the double-click speed as instructed and click OK. The mouse pointer moves too fast or too slow Try changing the speed setting in the mouse control utility. 1. Open the Control Panel, select the Mouse icon and press Enter. 2. Click the Pointer Options tab. 3.
Troubleshooting Memory expansion Refer also to Chapter 8, Optional Devices, for information on installing memory modules. Problem Procedure Beep sounds. (Two beeps, a dash and a dot, for a defective memory module in slot A. Three beeps, a dash and two dots for slot B. When both beeps sound, both memories in slot A and B are defective.) Make sure the memory module installed in the expansion slot is compatible with the computer. If an incompatible module has been installed, follow the steps below. 1.
Troubleshooting Monitor Refer also to Chapter 8, Optional Devices, and to your monitor’s documentation. Problem Procedure Monitor does not turn on Make sure that the external monitor’s power switch is on. Confirm that the external monitor’s power cable is plugged into a working power outlet. No display Try adjusting the contrast and brightness controls on the external monitor. Press hot keys Fn + F5 to change the display priority and make sure it is not set for the internal display.
Troubleshooting Problem Procedure You place a call, but a connection can’t be made Make sure the settings are correct in your communications application. After making a call you can’t hear a ring Make sure the tone or pulse selection in your communications application is set correctly. You can also use the ATD command. Communication is cut off unexpectedly The computer will automatically cut off communication when connection with the carrier is not successful for a set time interval.
Troubleshooting Wireless LAN If the following procedures do not restore LAN access, consult your LAN administrator. For more information on wireless communication, refer to Chapter 4, Operating Basics. Problem Procedure Cannot access Wireless LAN Make sure the computer’s wireless communication switch is set to on. If problems persist, contact your LAN administrator. Bluetooth For more information on wireless communication, refer to Chapter 4, Operating Basics.
Troubleshooting TOSHIBA support If you require any additional help using your computer or if you are having problems operating the computer, you may need to contact TOSHIBA for additional technical assistance. Before you call Some problems you experience may be related to software or the operating system, it is important to investigate other sources of assistance first. Before contacting TOSHIBA, try the following: ■ Review troubleshooting sections in the documentation for software and peripheral devices.
TECRA M2 Appendix A Specifications This appendix summarizes the computer’s technical specifications. Physical Dimensions Weight (typical) 2.26 kilograms, configured with: 14"XGA, 256MB RAM, 40GB HDD, DVD-ROM drive, modem, LAN(100 Mbit), Wireless LAN, 6cell battery. Weight will vary with other configurations. Above weights are measured at a specific criteria. They are not guaranteed as the maximum weight of the actual product. Size 314 (w) x 260 (d) x 31.5/34.
Specifications Power Requirements AC adaptor 100-240 volts AC 50 or 60 hertz (cycles per second) Computer 15 VDC 5.
Specifications Network control unit (NCU) TECRA M2 Transmitting level -10 dBm Receiving level -10 to -40 dBm Input/output impedance 600 ohms ±30% Error correcting MNP class 4 and ITU-T V.42 Data compression MNP class 5 and ITU-T V.42bis Power supply +3.
TECRA M2 Appendix B AC Power Cord and Connectors The power cord’s AC input plug must be compatible with the various international AC power outlets and the cord must meet the standards for the country/region in which it is used. All cords must meet the following specifications: Length: Minimum 2 meters Wire size: Minimum 0.75 mm² Current rating: Minimum 2.5 amperes Voltage rating: 125 or 250 VAC (depending on country/region’s power standards) Certification agencies U.S.
AC Power Cord and Connectors France: UTE Switzerland: SEV Germany: VDE United Kingdom: BSI In Europe, power cords must be VDE type, H05VVH2-F and two conductor. For the United States and Canada, plug configuration must be a 2-15P (250 V) or 1-15P (125 V) as designated in the U.S. National Electrical code handbook and the Canadian Electrical Code Part II. The following illustrations show the plug shapes for the U.S.A. and Canada, the United Kingdom, Australia and Europe.
TECRA M2 Appendix C Display Controller and Modes Display controller The display controller interprets software commands into hardware commands that turn particular pels on or off. The controller is an advanced Video Graphics Array (VGA) that provides Super VGA (SVGA) and Extended Graphics Array (XGA), Super Extended Graphics Array (SXGA), Super Extended Graphics Array plus (SXGA+), support for the internal LCD and external monitors. Two models are available: ■ 14.
Display Controller and Modes Table1 Video modes (VGA) LCD colors CRT colors Scanning frequency Vertical (Hz) 8×8 16 of 256K 16 of 256K 70 80 × 25 Characters 8×8 16 of 256K 16 of 256K 70 VGA Text 40 × 25 Characters 8 × 14 16 of 256K 16 of 256K 70 2*, 3* VGA Text 80 × 25 Characters 8 × 14 16 of 256K 16 of 256K 70 0+, 1+ VGA Text 40 × 25 Characters 9 × 16 16 of 256K 16 of 256K 70 2+, 3+ VGA Text 80 × 25 Characters 9 × 16 16 of 256K 16 of 256K 70 4, 5 VGA Grph 320 × 200
Display Controller and Modes Table1 Video modes (VGA) continued Video mode Type Resolution Character matrix (pels) LCD colors CRT colors Scanning frequency Vertical (Hz) D VGA Grph 320 × 200 Pels 8×8 16 of 256K 16 of 256K 70 E VGA Grph 640 × 200 Pels 8×8 16 of 256K 16 of 256K 70 F VGA Grph 640 × 350 Pels 8 × 14 Mono Mono 70 10 VGA Grph 640 × 350 Pels 8 × 14 16 of 256K 16 of 256K 70 11 VGA Grph 640 × 480 Pels 8 × 16 2 of 256K 2 of 256K 60 12 VGA Grph 640 × 480 Pel
Display Controller and Modes Table 2 Video modes (XGA) Resolution LCD colors CRT colors Vertical frequency (Hz) 640 × 480 256/256K 256/256K 60 75 85 100 800 × 600 256/256K 256/256K 60 75 85 100 1024 × 768 256/256K 256/256K 60 75 85 100 1280 × 1024 256/256K (Virtual) 256/256K 60 75 85 100 1600 × 1200 256/256K (Virtual) 256/256K 60 75 85 100 1920 × 1440 256/256K (Virtual) 256/256K 60 75 85 2048 × 1536 256/256K (Virtual) 256/256K 60 75 Some SVGA modes are not supported at LCD+C
Display Controller and Modes Table 2 Video modes (XGA) continued Resolution LCD colors CRT colors Vertical frequency (Hz) 640 × 480 64K/64K 64K/64K 60 75 85 100 800 × 600 64K/64K 64K/64K 60 75 85 100 1024 × 768 64K/64K 64K/64K 60 75 85 100 1280 × 1024 64K/64K (Virtual) 64K/64K 60 75 85 100 1600 × 1200 64K/64K (Virtual) 64K/64K 60 75 85 100 1920 × 1440 64K/64K (Virtual) 64K/64K 60 75 85 2048 × 1536 64K/64K (Virtual) 64K/64K 60 75 Some SVGA modes are not supported at LCD+CRT s
Display Controller and Modes Table 2 Video modes (XGA) continued Resolution LCD colors CRT colors Vertical frequency (Hz) 640 × 480 16M/16M 16M/16M 60 75 85 100 800 × 600 16M/16M 16M/16M 60 75 85 100 1024 × 768 16M/16M 16M/16M 60 75 85 100 1280 × 1024 16M/16M (Virtual) 16M/16M 60 75 85 100 1600 × 1200 16M/16M (Virtual) 16M/16M 60 75 85 100 1920 × 1440 16M/16M (Virtual) 16M/16M 60 75 2048 × 1536 16M/16M (Virtual) 16M/16M 60 75 Some SVGA modes are not supported at LCD+CRT simu
Display Controller and Modes Table 3 Video modes (Super XGA+) Resolution LCD colors CRT colors Vertical frequency (Hz) 640 × 480 256/256K 256/256K 60 75 85 100 800 × 600 256/256K 256/256K 60 75 85 100 1024 × 768 256/256K 256/256K 60 75 85 100 1280 × 1024 256/256K 256/256K 60 75 85 100 1400 × 1050 256/256K 256/256K 60 1600 × 1200 256/256K (Virtual) 256/256K 60 75 85 100 1920 × 1440 256/256K (Virtual) 256/256K 60 75 85 2048 × 1536 256/256K (Virtual) 256/256K 60 75 TECRA M2
Display Controller and Modes Table 3 Video modes (Super XGA+) continued Resolution LCD colors CRT colors Vertical frequency (Hz) 640 × 480 64K/64K 64K/64K 60 75 85 100 800 × 600 64K/64K 64K/64K 60 75 85 100 1024 × 768 64K/64K 64K/64K 60 75 85 100 1280 × 1024 64K/64K 64K/64K 60 75 85 100 1400 × 1050 64K/64K 64K/64K 60 1600 × 1200 64K/64K (Virtual) 64K/64K 60 75 85 100 1920 × 1440 64K/64K (Virtual) 64K/64K 60 75 85 2048 × 1536 64K/64K (Virtual) 64K/64K 60 75 TECRA M2 C-8
Display Controller and Modes Table 3 Video modes (Super XGA+) continued Resolution LCD colors CRT colors Vertical frequency (Hz) 640 × 480 16M/16M 16M/16M 60 75 85 100 800 × 600 16M/16M 16M/16M 60 75 85 100 1024 × 768 16M/16M 16M/16M 60 75 85 100 1280 × 1024 16M/16M 16M/16M 60 75 85 100 1400 × 1050 16M/16M 16M/16M 60 1600 × 1200 16M/16M (Virtual) 16M/16M 60 75 85 100 1920 × 1440 16M/16M (Virtual) 16M/16M 60 75 2048 × 1536 16M/16M (Virtual) 16M/16M 60 75 Some SVGA modes a
TECRA M2 Appendix D If your computer is stolen Always take care of your computer and try to prevent it from being stolen. You are the owner of a valuable technical device, which may be highly attractive to thieves, so please do not leave it unattended in a public place. To further help protect against theft, security cables can be bought for use with your notebook when it is being used at home or in the office.
If your computer is stolen TOSHIBA Theft Registration Send to: Fax number: TOSHIBA Europe GmbH Technical Service and Support Leibnizstr. 2 93055 Regensburg Germany +49 (0) 941 7807 925 Country stolen: Machine type: (e.g. Tecra M2) Model number: (e.g. PTM20 YXT) Serial number: (e.g. 70123456E) Date stolen: Warranty seal: (e.g.
TECRA M2 Appendix E ASCII Character Codes This appendix shows the American Standard Code for Information Interchange (ASCII) on the following pages. The characters in the IBM char column appear on your display when you type the corresponding ASCII code (as described in Chapter 5, Keyboard). The characters that are printed, however, depend on the software you are using. For most software, the printed output for decimal codes 32 to 128 will match your screen display.
ASCII Character Codes TECRA M2 Dec code Hex code 000 001 002 003 004 005 006 007 008 009 010 011 012 013 014 015 016 017 018 019 020 021 022 023 024 025 026 027 028 029 030 031 00 01 02 03 04 05 06 07 08 09 0A 0B 0C 0D 0E 0F 10 11 12 13 14 15 16 17 18 19 1A 1B 1C 1D 1E 1F IBM char ♥ ♦ ♣ ♠ • !! ¶ § ↑ ↓ → ← ↔ ▲ ▼ Sort seq Ctrl char 000 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 NUL SOH STX ETX EOT ENQ ACK BEL BS HT LF VT FF CR SO SI DLE DC1 DC2 DC3 DC4 NAK
ASCII Character Codes Dec code Hex code IBM char Sort seq Dec code Hex code IBM char Sort seq 032 033 034 035 036 037 038 039 040 041 042 043 044 045 046 047 048 049 050 051 052 053 054 055 056 057 058 059 060 061 062 063 20 21 22 23 24 25 26 27 28 29 2A 2B 2C 2D 2E 2F 30 31 32 33 34 35 36 37 38 39 3A 3B 3C 3D 3E 3F space ! “ # $ % & ’ ( ) * + , .
ASCII Character Codes Dec code Hex code IBM char Sort seq Dec code Hex code IBM char Sort seq 096 097 098 099 100 101 102 103 104 105 106 107 108 109 110 111 112 113 114 115 116 117 118 119 120 121 122 123 124 125 126 127 60 61 62 63 64 65 66 67 68 69 6A 6B 6C 6D 6E 6F 70 71 72 73 74 75 76 77 78 79 7A 7B 7C 7D 7E 7F ’ a b c d e f g h i j k l m n o p q r s t u v w x y z { 96 97 98 99 100 101 102 103 104 105 106 107 108 109 110 111 112 113 114 115 116 117 118 119 120 121 122 123 124 125 126 127 1
ASCII Character Codes Dec code Hex code IBM char Sort seq Dec code Hex code 160 161 162 163 164 165 166 167 168 169 170 171 172 173 174 175 176 177 178 179 180 181 182 183 184 185 186 187 188 189 190 191 A0 A1 A2 A3 A4 A5 A6 A7 A8 A9 AA AB AC AD AE AF B0 B1 B2 B3 B4 B5 B6 B7 B8 B9 BA BB BC BD BE BF á í ó ú ñ Ñ a o ¿ 65 73 79 85 78 78 166 167 63 169 170 171 172 33 34 34 192 193 194 195 196 197 198 199 200 201 202 203 204 205 206 207 208 209 210 211 212 213 214 215 216 217 218 219 220 221 222 223
ASCII Character Codes TECRA M2 Dec code Hex code IBM char 224 225 226 227 228 229 230 231 232 233 234 235 236 237 238 239 240 241 242 243 244 245 246 247 248 249 250 251 252 253 254 255 E0 E1 E2 E3 E4 E5 E6 E7 E8 E9 EA EB EC ED EE EF F0 F1 F2 F3 F4 F5 F6 F7 F8 F9 FA FB FC FD FE FF α ß Γ Π ∑ σ µ ϒ Φ Θ Ω δ ϕ φ Ε Λ Ξ ± ≥ ≤ ⌠ ⌡ ÷ ≈ Sort seq 83 ° √ η 2 E-6
TECRA M2 Appendix F Wireless LAN Card Specifications Form Factor Compatibility Network Operating System Media Access Protocol Data Rate User’s Manual Mini PCI TypeIII ■ IEEE 802.11 Standard for Wireless LANS ■ Wi-Fi (Wireless Fidelity) certified by the Wi-Fi Alliance. The ‘Wi-Fi CERTIFIED’ logo is a certification mark of the Wi-Fi Alliance.
Wireless LAN Radio Characteristics Radio Characteristics of Wireless LAN Cards may vary according to: ■ Country/region where the product was purchased ■ Type of product Wireless communication is often subject to local radio regulations. Although Wireless LAN wireless networking products have been designed for operation in the license-free 2.4GHz and 5GHz band, local radio regulations may impose a number of limitations to the use of wireless communication equipment.
Wireless LAN Supported Frequency Sub-bands Subject to the radio regulations that apply in the countries/regions, your Wireless LAN card may support a different set of 5GHz / 2.4GHz channels. Consult your Authorized Wireless LAN or TOSHIBA Sales office for information about the radio regulations that apply in the countries/regions. Wireless IEEE 802.11 Channels Sets (Revision B and G) Frequency Range Channel ID 2400-2483.
Wireless LAN Wireless IEEE 802.
TECRA M2 Appendix G Internal Modem Guide This appendix describes how to install and the remove the internal modem. Do not disassemble the computer beyond the steps described in this instruction or touch any components not specifically described. Installing the internal modem The internal modem is preinstalled. The following is for information only. To install the internal modem, follow the steps below. 1. Save your data and turn off the computer. 2. Disconnect the AC adaptor and other peripheral devices.
Internal Modem Guide Removing the internal modem To remove the internal modem, follow the steps below. 1. Save your data and turn off the computer. 2. Disconnect the AC adaptor and any other peripheral device. 3. Turn the computer upside down and remove the battery pack. 4. Remove one screw securing the cover. 5. Remove the modem cover. 6. Remove two screws and remove the modem board. 7. Disconnect the modem cable. 8. Secure the modem cover with one screw. 9. Install the battery pack.
TECRA M2 Glossary The terms in this glossary cover topics related to this manual. Alternate naming is included for reference. A AccuPoint: A pointing device integrated into the TOSHIBA computer keyboard. adaptor: A device that provides an interface between two dissimilar electronic devices. For example, the AC adaptor modifies the power from a wall outlet for use by the computer.
Glossary async: Short for asynchronous. asynchronous: Lacking regular time relationship. As applied to computer communications, asynchronous refers to the method of transmitting data that does not require a steady stream of bits to be transmitted at regular time intervals. B backup: A duplicate copy of files kept as a spare in case the original is destroyed. batch file: A file that can be executed from the system prompt containing a sequence of operating system commands or executable files.
Glossary C cache memory: High speed memory which stores data that increases processor speed and data transfer rate. When the CPU reads data from main memory, it stores a copy of this data in cache memory. The next time the CPU needs that same data, it looks for it in the cache memory rather than the main memory, which saves time. The computer has two cache levels. Level one is incorporated into the processor and level two resides in external memory.
Glossary components: Elements or parts (of a system) which make up the whole (system). computer program: A set of instructions written for a computer that enable it to achieve a desired result. computer system: A combination of hardware, software, firmware, and peripheral components assembled to process data into useful information. configuration: The specific components in your system (such as the terminal, printer, and disk drives) and the settings that define how your system works.
Glossary disk drive: The device that randomly accesses information on a disk and copies it to the computer’s memory. It also writes data from memory to the disk. To accomplish these tasks, the unit physically rotates the disk at high speed past a read-write head. disk storage: Storing data on magnetic disk. Data is arranged on concentric tracks much like a phonograph record. diskette: A removable disk that stores magnetically encoded data. Also called a floppy disk.
Glossary execute: To interpret and execute an instruction. Extended Capability Port: An industry standard that provides a data buffer, switchable forward and reverse data transmission, and run length encoding (RLE) support. F fast infrared: An industry standard that enables cableless infrared serial data transfer at speeds of up to 4 Mbps. file: A collection of related information; a file can contain data, programs, or both.
Glossary host computer: The computer that controls, regulates, and transmits information to a device or another computer. hot key: The computer’s feature in which certain keys in combination with the extended function key, Fn, can be used to set system parameters, such as speaker volume. HW Setup: A TOSHIBA utility that lets you set the parameters for various hardware components. I icon: A small graphic image displayed on the screen or in the indicator panel.
Glossary K K: Taken from the Greek word kilo, meaning 1000; often used as equivalent to 1024, or 2 raised to the 10th power. See also byte and kilobyte. KB: See kilobyte. keyboard: An input device containing switches that are activated by manually pressing marked keys. Each keystroke activates a switch that transmits a specific code to the computer. For each key, the transmitted code is, in turn, representative of the (ASCII) character marked on the key.
Glossary monitor: A device that uses rows and columns of pixels to display alphanumeric characters or graphic images. See also CRT. motherboard: A name sometimes used to refer to the main printed circuit board in processing equipment. It usually contains integrated circuits that perform the processor’s basic functions and provides connectors for adding other boards that perform special functions. Sometimes called a main board.
Glossary password: A unique string of characters used to identify a specific user. The computer provides various levels of password protection such as user, supervisor and eject. pel: The smallest area of the display that can be addressed by software. Equal in size to a pixel or group of pixels. See pixel. peripheral component interconnect: An industry standard 32-bit bus. peripheral device: An I/O device that is external to the central processor and/or main memory such as a printer or a mouse.
Glossary RJ45: A modular LAN jack. ROM: Read Only Memory: A nonvolatile memory chip manufactured to contain information that controls the computer’s basic operation. You cannot access or change information stored in ROM. S SCSI: Small Computer System Interface is an industry standard interface for connection of a variety of peripheral devices. SD cards: Secure Digital cards are flash memory widely used in a variety of digital devices such as digital cameras and Personal Digital Assistants.
Glossary T terminal: A typewriter-like keyboard and CRT display screen connected to the computer for data input/output. TFT display: A liquid crystal display (LCD) made from an array of liquid crystal cells using active-matrix technology with thin film transistor (TFT) to drive each cell. TouchPad: A pointing device integrated into the TOSHIBA computer palm rest. TTL: Transistor-transistor logic. A logic circuit design that uses switching transistors for gates and storage.
TECRA M2 Index A C AC adaptor 1-4, 2-17 Connecting 3-4 AC Power Cord B-1 Accessing HW Setup 7-1 AccuPoint 2-9, 4-2 Advanced Port Replicator III 1-16, 8-21 Analyzing a problem 9-2 ASCII Character Codes E-1 ASCII characters E-1 Caps Lock 5-1 Care and use of the battery pack 6-7 CD-RW/DVD-ROM 1-5, 2-15, 4-10 CDs 2-14 Writing 4-10 Charging the batteries 6-9 Cleaning the computer 4-28 Communications 1-8 Connecting LAN cable 4-27 Connectors B-1 B Backside 2-5 Battery 2nd battery 6-6 additional 8-15 High capa
Index E I Emulating keys 5-2 Environmental Requirements A-1 Extending battery life 6-12 External monitor 2-4, 8-17 i.
Index P Panel power on/off 6-18 Parallel port 2-2 PC card slot 2-3 PC cards 8-2 Physical Dimensions A-1 Placement of the computer 3-2 Ports 1-7 Power Turning off 3-7 Turning on 3-6 Power button 2-10 Power conditions 6-1 Power indicators 6-4 Power-up modes 6-18 Preliminary checklist 9-2 Printer parallel 8-22 Problem solving process 9-1 Problems AC power 9-5 Battery 9-5 Bluetooth 9-20 CD-RW/DVD-ROM drive 9-9 DVD Multi drive 9-11 DVD±R/±RW drive 9-12 DVD-ROM drive 9-8 Floppy disk drive 9-13 Hard disk drive 9-
Index T U Temporarily changing modes 5-8 TOSHIBA Audio Effect 1-15 TOSHIBA ConfigFree 1-14 TOSHIBA Console 1-14 TOSHIBA Console button 2-9 TOSHIBA Controls 1-13 TOSHIBA Dual Pointing Device 1-7, 4-1 TOSHIBA IP Phone 1-14 TOSHIBA Mobile Extension 1-14 TOSHIBA PC DiagnosticTool 1-14 TOSHIBA Power Saver 1-13 TOSHIBA Presentation button 2-9 TOSHIBA SD Memory Boot Utility 1-13 TOSHIBA support 9-21 TOSHIBA Theft Registration D-2 TOSHIBA Zooming Utility 1-13, 5-6 Touch Pad 2-9, 4-2 Troubleshooting 9-1 TV 8-18 T
