TECRA M3 TOSHIBA TECRA M3 Portable Personal Computer User’s Manual
User’s Manual Copyright © 2005 by TOSHIBA Corporation. All rights reserved. Under the copyright laws, this manual cannot be reproduced in any form without the prior written permission of TOSHIBA. No patent liability is assumed, with respect to the use of the information contained herein.
User’s Manual EU Declaration of Conformity This product is carrying the CE-Mark in accordance with the related European Directives. Responsible for CE-Marking is TOSHIBA Europe GmbH, Hammfelddamm 8, 41460 Neuss, Germany. The complete and official EU Declaration of Conformity can be found on TOSHIBA’s web site http://epps.toshiba-teg.com on the Internet.
User’s Manual CE compliance This product is labelled with the CE Mark in accordance with the related European Directives, notably Electromagnetic Compatibility Directive 89/336/EEC for the notebook and the electronic accessories including the supplied power adapter, the Radio Equipment and Telecommunications Terminal Equipment Directive 99/5/EEC in case of implemented telecommunication accessories and the Low Voltage Directive 73/23/EEC for the supplied power adapter.
User’s Manual Network Compatibility Statement This product is designed to work with, and is compatible with the following networks. It has been tested to and found to conform with the additional requirements conditional in EG 201 121.
User’s Manual Description on Laser specification The optical disk drive such as CD-ROM drive, DVD-ROM drive, DVD-ROM&CD-R/RW drive, DVD Super Multi drive and DVD±R/±RW drive that is used in this computer is equipped with laser. The classification label with the following sentence is affixed to the surface of the drive.
TECRA M3 Table of Contents Preface Manual contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . xv Conventions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . xvi Abbreviations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . xvi Icons . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Table of Contents Front with the display open . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2-8 System indicators . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2-11 Keyboard indicators . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2-12 USB floppy disk drive (optional) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Table of Contents Using the USB floppy disk drive (optional) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-4 Connecting USB floppy disk drive . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-4 Disconnecting USB floppy disk drive . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-4 Changing Slim Select Bay modules . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-5 Removing a module. . . . . . . . . . . . . . . .
Table of Contents Wireless communications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4-27 Wireless LAN. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4-27 Bluetooth wireless technology. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4-28 BluetoothTM Stack for Windows® by TOSHIBA . . . . . . . . . . . . . . . . . . . . . . . . . . . .4-29 Wireless communication switch . .
Table of Contents Retaining data with power off . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Extending battery life . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Replacing the battery pack. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Removing the battery pack . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Installing the battery pack . . . . . . .
Table of Contents Slim Select Bay HDD adaptor (Black) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8-16 USB floppy disk drive. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8-17 External monitor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8-17 TV . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Table of Contents Wireless LAN . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Bluetooth . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Printer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . TV output signal. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Table of Contents xiv User’s Manual
TECRA M3 Preface Congratulations on your purchase of the TECRA M3 computer. This powerful notebook computer provides excellent expansion capability, including multimedia devices, and it is designed to provide years of reliable, high-performance computing. This manual tells how to set up and begin using your TECRA M3 computer. It also provides detailed information on configuring your computer, basic operations and care, using optional devices and troubleshooting.
Preface Chapter 4, Operating Basics, includes instructions on using the following devices: TOSHIBA Dual Pointing Device, USB floppy disk drive, Slim Select Bay modules, optical media drives, sound system, modem, Wireless communication features, LAN. It also provides tips on care of the computer, floppy disks and CD/DVDs. Chapter 5, The Keyboard, describes special keyboard functions including the keypad overlay and hot keys.
Preface Key operation Some operations require you to simultaneously use two or more keys. We identify such operations by the key top symbols separated by a plus sign (+). For example, Ctrl + C means you must hold down Ctrl and at the same time press C. If three keys are used, hold down the first two and at the same time press the third.
Preface xviii User’s Manual
TECRA M3 General Precautions TOSHIBA computers are designed to optimize safety, minimize strain and withstand the rigors of portability. However, certain precautions should be observed to further reduce the risk of personal injury or damage to the computer. Be certain to read the general precautions below and to note the cautions included in the text of the manual. Stress injury Carefully read the Safety Instruction Manual.
General Precautions Pressure or impact damage Do not apply heavy pressure to the computer or subject it to strong impact. Excessive pressure or impact can cause damage to computer components or otherwise cause malfunctions. PC card overheating Some PC cards can become hot with prolonged use. Overheating of a PC card can result in errors or instability in the PC card operation. Also be careful when you remove a PC card that has been used for a long time.
General Precautions CPU performance may also vary from specifications due to design configuration. Under some conditions, your computer product may automatically shutdown. This is a normal protective feature designed to reduce the risk of lost data or damage to the product when used outside recommended conditions. To avoid risk of lost data, always make back-up copies of data by periodically storing it on an external storage medium.
General Precautions xxii User’s Manual
TECRA M3 Chapter 1 Introduction This chapter provides an equipment checklist, and it identifies the computer’s features, options and accessories. Some of the features described in this manual may not function properly if you use an operating system that was not preinstalled by TOSHIBA. Equipment checklist Carefully unpack your computer. Save the box and packing materials for future use.
Introduction Software Microsoft® Windows XP Professional ■ The following software is preinstalled: ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ Microsoft® Windows XP Professional Microsoft Internet Explorer TOSHIBA SD Memory Boot Utility DVD Video Player TOSHIBA Dual Pointing Device utility TOSHIBA Power Saver TOSHIBA Mobile Extension TOSHIBA Assist TOSHIBA ConfigFree TOSHIBA Zooming Utility TOSHIBA PC Diagnostic Tool TOSHIBA Controls TOSHIBA Mic Effect TOSHIBA Password Utility Online manual Documentation and Backup Me
Introduction Features The computer uses TOSHIBA’s advanced Large Scale Integration (LSI), Complementary Metal-Oxide Semiconductor (CMOS) technology extensively to provide compact size, minimum weight, low power usage, and high reliability. This computer incorporates the following features and benefits: Processor Built-in The computer is equipped with an Intel® processor. Intel® Pentium® M processor, which incorporates a 32KB level 1 cache memory and a 1MB level 2 cache memory.
Introduction AC adaptor The AC adaptor provides power to the system and recharges the batteries when they are low. It comes with a detachable power cord. It encloses 2-pin or 3-pin plug type. Because it is universal, it can receive a range of AC voltage from 100 to 240 volts; however, the output current varies among different models. Using the wrong model can damage your computer. Refer to the AC adaptor section in Chapter 2, The Grand Tour. Disks Hard disk drive Available in four sizes. ■ 40.
Introduction User’s Manual DVD-ROM&CD-R/RW drive Some models are equipped with a full-size, DVD-ROM&CD-R/RW drive module that lets you run CD/DVDs without using an adaptor. It reads DVD-ROMs at maximum 8 speed and CD-ROMs at maximum 24 speed. It writes CD-R at maximum 24 speed and CD-RW at maximum 24 speed. For reading, this drive supports the same formats as the DVD-ROM drive.
Introduction Display The computer’s LCD display panel supports high-resolution video graphics. The LCD screen can be set at a wide range of viewing angles for maximum comfort and readability. Built-in 14.1" TFT LCD screen, 16 M colors, with one of the following resolutions: ■ XGA, 1024 horizontal × 768 vertical pixels ■ SXGA+, 1400 horizontal × 1050 vertical pixels Graphics controller Graphics controller maximizes display performance.
Introduction Docking interface This port enables connection of an optional Advanced Port Replicator III described in the Options section. i.LINK™ (IEEE1394) This port enables high-speed data transfer directly from external devices such as digital video cameras. Infrared The serial infrared port is compatible with Infrared Data Association (IrDA 1.1) standards. It enables cableless 4 Mbps, 1.152 Mbps, 115.2 kbps, 57.6 kbps, 38.4 kbps, 19.2 kbps or 9.6 kbps data transfer with IrDA 1.
Introduction Communications 1-8 Modem An internal modem provides capability for data and fax communication. It supports V.90 (V.92). The speed of data transfer and fax depends on analog telephone line conditions. It has a modem jack for connecting to a telephone line. Both of V.90 and V.92 are supported only in USA, Canada, UK, France, Germany and Australia. Only V.90 is available in other regions.
Introduction Wireless LAN Some computers in this series are equipped with a Wireless LAN mini-PCI card that is compatible with other LAN systems based on Direct Sequence Spread Spectrum/Orthogonal Frequency Division Multiplexing radio technology that complies with the IEEE 802.11 Standard (Revision A, B or G), and Turbo Mode. ■ Theoretical maximum speed: 54Mbps(IEEE802.11a, 802.11g) ■ Theoretical maximum speed: 11Mbps(IEEE802.
Introduction Wireless communication switch This switch turns the Wireless LAN and Bluetooth functions on and off. Slim Select Bay Modules Slim Select Bay is a single-drive bay that accommodates a CD-ROM drive, DVD-ROM drive, DVD-ROM&CD-R/RW drive, DVD Super Multi drive, DVD±R/±RW drive, secondary hard disk drive or secondary battery pack. The TOSHIBA Mobile Extension enables hot insertion of modules when you are using a plug and play operating system.
Introduction Special features The following features are either unique to TOSHIBA computers or are advanced features, which make the computer more convenient to use. User’s Manual TOSHIBA Assist button Press this button to launch an application automatically. The default is TOSHIBA Assist. TOSHIBA Presentation button Press this button to change internal display, external display, simultaneous display, or multi-monitor display.
Introduction 1-12 Intelligent power supply A microprocessor in the computer’s intelligent power supply detects the battery’s charge and calculates the remaining battery capacity. It also protects electronic components from abnormal conditions, such as voltage overload from an AC adaptor. You can monitor remaining battery capacity. Use the Battery remaining item in TOSHIBA Power Saver. Battery save mode This feature lets you save battery power.
Introduction User’s Manual Optical media drive power icon Use this to turn the power of the optical media drive on or off. Clicking on the optical media drive icon on the taskbar will turn the power of the optical media drive on or off. If the optical media drive power is off, the disc tray will not open even if the eject button is pushed. The power of the optical media drive can be turned on using the optical media drive icon.
Introduction Utilities This section describes preinstalled utilities and tells how to start them. For details on operations, refer to each utility’s online manual, help files or readme.txt files. TOSHIBA Power Saver To access this power savings management program, click start, click Control Panel, click Performance and Maintenance and select the TOSHIBA Power Saver icon.
Introduction RecordNow! Basic for TOSHIBA You can create CD/DVDs in several formats including audio CDs that can be played on a standard stereo CD player and data CD/DVDs to store the files and folders on your hard disk drive. This software can be used on a model with DVD-ROM&CD-R/RW drive, DVD Super Multi drive and DVD±R/±RW drive. TOSHIBA Assist TOSHIBA Assist is a graphical user interface that provides easy access to help and services. It is the default function launched by the TOSHIBA Assist button.
Introduction NVIDIA Rotation Settings This utility let you rotate the desktop by 0 and 180 easily. It can rotate by clicking the icon in a taskbar or pressing Ctrl+Shft+R. In a multi-monitor setup, the display that contains the cursor is effective. TOSHIBA Password Utility This utility lets you set a password that restricts access to the computer.
Introduction Options You can add a number of options to make your computer even more powerful and convenient to use. The following options are available: User’s Manual Memory expansion A 256, 512 or 1,024 MB memory module (PC2-4200) can easily be installed in the computer. Battery pack An additional battery pack can be purchased from your TOSHIBA dealer. Use it as a spare or replacement. High capacity battery pack An additional battery pack can be purchased from your TOSHIBA dealer.
Introduction Wireless LAN Kit This option enables wireless LAN functions in computers that do not have wireless preinstalled. It is installed by dealers only. Bluetooth Kit This option enables Bluetooth wireless communications in computers that do not have Bluetooth preinstalled. It is installed by dealers only. Slim Select Bay options The following modules can be installed in the Slim Select Bay. All other modules are options. 1-18 CD-ROM Refer to the Features section for details.
TECRA M3 Chapter 2 The Grand Tour This chapter identifies the various components of your computer. Become familiar with each component before you operate the computer. Certain notebook chassis are designed to accommodate all possible configurations for an entire product series. Your selected model may not have all the features and specifications corresponding to all of the icons or switches shown on the notebook chassis, unless you have selected all those features.
The Grand Tour Off On Infrared port This infrared port is compatible with Infrared Data Association (IrDA 1.1) standards. It enables cableless 4 Mbps, 1.15 Mbps, 115.2 kbps, 57.6 kbps, 38.4 kbps, 19.2 kbps or 9.6 kbps data transfer with IrDA 1.1 compatible external devices. Wireless communication switch Slide this switch to the left to turn off Wireless LAN and Bluetooth functions. Slide it to the right to turn on the functions. Some models are equipped with a Wireless communication.
The Grand Tour Security lock slot A security cable attaches to this slot. The optional security cable anchors your computer to a desk or other large object to deter theft. i.LINK (IEEE1394) port Connect an external device, such as a digital video camera to this port for high-speed data transfer. ExpressCard slot The ExpressCard slot can accommodate an ExpressCard. ExpressCard eject button This is a button for taking out an ExpressCard from the ExpressCard slot.
The Grand Tour Right side The following figure shows the computer’s right side. Headphone jack Microphone jack USB ports Slim Select Bay External monitor port The right side of the computer Headphone jack A 3.5 mm mini headphone jack enables connection of stereo headphones. Microphone jack A 3.5 mm mini microphone jack enables connection of a three-conductor mini jack for monaural microphone input. Universal Serial Bus (USB 2.0) ports Two Universal Serial Bus ports are on the right side.
The Grand Tour Back side The following figure shows the computer’s back side. Video-out jack Modem jack LAN active indicator (orange) LAN jack DC IN 15V jack Link indicator (green) The back side of the computer Video-out jack Plug an S-Video cable into this jack for video-out. The S-Video cable carries video signal. Modem jack The modem jack lets you use a modular cable to connect the modem directly to a telephone line.
The Grand Tour LAN active indicator (orange) This indicator glows orange when data is being exchanged between the computer and the LAN. DC IN 15V jack The AC adaptor connects to this jack. Use only the model of AC adaptor that comes with the computer. Using the wrong adaptor can damage your computer. DC IN 15V Underside The following figure shows the underside of the computer. Make sure the display is closed before turning over your computer.
The Grand Tour Battery release latch Slide and hold this latch to release the battery pack for removal. For detailed information on removing the battery packs, refer to Chapter 6, Power and Power-Up Modes. Docking interface This port enables connection of an optional Advanced Port Replicator III described in Chapter 8, Optional Devices. Keep foreign objects out of the docking interface port. A pin or similar object can damage the computer's circuitry. A plastic shutter protects the connector.
The Grand Tour Front with the display open This section shows the computer with the LCD display panel open. Refer to the appropriate illustration for details. To open the display, slide the display latch on the front of the LCD display panel and lift up. Position the LCD display panel at a comfortable viewing angle.
The Grand Tour User’s Manual LCD screen The LCD screen displays high-contrast text and graphics. The available resolution depends on the model. With XGA, you can change the resolution between 800 × 600 and 1024 × 768 pixels. With SXGA, between 800 × 600 and 1400 × 1050 pixels. Refer to Display Controller and Modes section in Appendix B. When the computer operates on the AC adaptor the LCD screen’s image will be somewhat brighter than when it operates on battery power.
The Grand Tour TOSHIBA Presentation button Press this button to change internal display, simultaneous display, or multi-monitor display. The default setting is the simultaneous display on LCD and CRT with resolution of 1024 × 768. When you press this button twice, the display mode returns to single display on LCD only. Setting of multi-monitor display in Windows XP, computer changes its display mode to the multi-monitor display on LCD and CRT.
The Grand Tour System indicators LEDs, next to icons, light when various computer operations are in progress. SD card DC IN Power Battery HDD Slim Select Bay Wireless communication System indicators User’s Manual SD card The SD card indicator glows green when the computer is accessing the SD card slot. DC IN The DC IN indicator glows in green when DC power is supplied from the AC power adaptor.
The Grand Tour Wireless communication The Wireless communication indicator glows when the Bluetooth and wireless LAN functions are turned on. Some models are equipped with a Wireless communication. Keyboard indicators The figures below show the positions of the keypad overlay indicators and the Caps Lock indicator. When the Arrow mode indicator glows the keypad overlay lets you control the cursor. When the Numeric mode indicator glows the keypad overlay lets you enter numbers.
The Grand Tour Arrow mode When the Arrow mode indicator lights green, you can use the keypad overlay (gray labeled keys) as cursor keys. Refer to the Keypad overlay section in Chapter 5, The Keyboard. Numeric mode You can use the keypad overlay (gray labeled keys) for numeric input when the Numeric mode indicator lights green. Refer to the Keypad overlay section in Chapter 5, The Keyboard. USB floppy disk drive (optional) The optional USB floppy disk drive accommodates 1.
The Grand Tour ■ The USB floppy disk drive should be placed on a flat, horizontal surface when in use. Do not set the drive on an incline greater than 20o while it is operating. ■ Do not set anything on top of the floppy disk drive. Optical media drives One of the following optical media drives is installed in the computer: DVD-ROM, DVD-ROM&CD-R/RW, DVD Super Multi and DVD±R/±RW drives. An ATAPI interface controller is used for CD/DVD-ROM operation.
The Grand Tour CDs ■ CD-R discs can be written only once. The recorded data cannot be erased or changed. ■ CD-RW discs can be recorded more than once. Use either 1, 2, or 4 multi speed CD-RW discs or high-speed 4- to 10-speed discs. The write speed of the ultra-speed CD-RW discs is maximum 24-speed. DVDs ■ DVD-R and DVD+R discs can be written only once. The recorded data cannot be erased or changed. ■ DVD-RW, DVD+RW and DVD-RAM discs can be recorded more than once.
The Grand Tour DVD Super Multi drive The full-size DVD Super Multi drive module lets you record data to rewritable CD/DVDs as well as run either 12 cm (4.72") or 8 cm (3.15") CD/DVDs without using an adaptor. The read speed is slower at the center of a disc and faster at the outer edge.
The Grand Tour AC adaptor The AC adaptor can automatically adjust to any voltage ranging from 100 to 240 volts and to a frequency of either 50 or 60 hertz, enabling you to use this computer in almost any country/region. And the adaptor converts AC power to DC power and reduces the voltage supplied to this computer. To recharge the battery, simply connect the AC adaptor to a power source and the computer. Refer to Chapter 6, Power and Power-Up Modes, for details.
The Grand Tour Use only the AC adaptor that came with the computer or an equivalent optional adaptor. Use of any other adaptors could damage your computer. TOSHIBA assumes no liability for any damage in such case. Use only the AC adaptor supplied as an accessory. Other AC adaptors have different voltage and terminal polarities and use of them may produce heat and smoke or even result in fire or rupture.
TECRA M3 Chapter 3 Getting Started This chapter provides basic information to get you started using your computer. It covers the following topics: ■ Setting up your work space — for your health and safety Be sure also to read the Safety Instruction Manual. This guide, which is included with the computer, explains product liability.
Getting Started General conditions In general, if you are comfortable, so is your computer, but read the following to make sure your work site provides a proper environment. ■ Make sure there is adequate space around the computer for proper ventilation. ■ Make sure the AC power cord connects to an outlet that is close to the computer and easily accessible. ■ The temperature should be 5 to 35 degrees Centigrade (41 to 95 degrees Fahrenheit) and the relative humidity should be 20 to 80 percent.
Getting Started Seating and posture The height of your chair in relation to the computer and keyboard as well as the support it gives your body are primary factors in reducing work strain. Refer to the following tips. Below eye level 90°angles Foot rest Posture and positioning of the computer ■ Place your chair so that the keyboard is at or slightly below the level of your elbow. You should be able to type comfortably with your shoulders relaxed. ■ Your knees should be slightly higher than your hips.
Getting Started Work habits A key to avoiding discomfort or injury from repetitive strain is to vary your activities. If possible, schedule a variety of tasks into your workday. If you must spend long periods at the computer, finding ways to break up the routine can reduce stress and improve your efficiency. ■ Sit in a relaxed posture. Good positioning of your chair and equipment as described earlier can reduce tension in your shoulders or neck and ease back strain. ■ Vary your posture frequently.
Getting Started ■ Use only the AC adaptor supplied with your computer or an equivalent adaptor that is compatible. Use of any incompatible adaptor could damage your computer. TOSHIBA assumes no liability for any damage caused by use of an incompatible adaptor. ■ The supplied power cord conforms to safety rules and regulations in the region the product is bought and should not be used outside this region.
Getting Started 2. Connect the AC adaptor’s DC output plug to the DC IN 15V jack on the back of the computer. DC IN 15V jack Connecting the adaptor to the computer 3. Plug the power cord into a live wall outlet. The Battery and DC IN indicators on the front of the computer should glow. Opening the display The computer’s LCD display panel can be rotated in a wide range of angles for optimal viewing. 1. Slide the display latch on the front of the computer to the right. 2.
Getting Started Turning on the power This section describes how to turn on the power. The Power button LED indicates the status. Refer to the Power indicators section in Chapter 6, Power and Power-Up Modes. ■ After you turn on the power for the first time, do not turn it off until you have set up the operating system. Refer to the section Starting up for the first time. ■ If the USB floppy disk drive is connected, make sure it is empty.
Getting Started Turning off the power The power can be turned off in one of the following modes: Shut down (Boot), Hibernation or Standby mode. Shut Down mode (Boot mode) When you turn off the power in Shut Down mode no data is saved and the computer will boot to the operating system’s main screen. 1. If you have entered data, save it to the hard disk or to a floppy disk. 2. Make sure all disk (disc) activity has stopped, then remove the CD/DVDs or floppy disk.
Getting Started ■ You can return to your previous working environment immediately when you turn on the computer. ■ Saves power by shutting down the system when the computer receives no input or hardware access for the duration set by the System hibernate feature. ■ You can use the panel power off feature. Starting Hibernation You can also enable Hibernation by pressing Fn + F4. Refer to Chapter 5, The Keyboard, for details. To enter Hibernation mode, follow the steps below. 1. Click start. 2.
Getting Started Standby mode If you have to interrupt your work, you can turn off the power without exiting from your software. Data is maintained in the computer’s main memory. When you turn on the power again, you can continue working right where you left off. ■ When the AC adaptor is connected, the computer will go into Standby mode according to the settings in the TOSHIBA Power Saver utility. ■ To restore operation from Standby mode, press the power button or press any key.
Getting Started Executing standby You can also enable Standby by pressing Fn + F3. See Chapter 5, The Keyboard, for details. You can enter standby mode in one of three ways: 1. Click start, click Turn Off Computer and click Stand By. 2. Close the computer’s LCD display panel. This feature must be enabled. Refer to the Setup Action tab in TOSHIBA Power Saver Utility described in the Control Panel. Open Performance and Maintenance and open TOSHIBA Power Saver. 3. Press the power button.
Getting Started Restoring the preinstalled software Restoring the complete system To restore the operating system and all preinstalled software, follow the steps below. Note: When sound is muted by the Fn + Esc key, turn it on before starting to restore. When you reinstall the Windows operating system, the hard disk will be reformatted and all data will be lost. 1. Load the Recovery Media in the optional optical media drive and turn off the computer’s power. 2. Hold down the F12 key and turn on the power.
TECRA M3 Chapter 4 Operating Basics This chapter gives information on basic operations including using the TOSHIBA Dual Pointing Devices, USB floppy disk drive (optional), changing Slim Select Bay modules, optical media drives, Sound System, Modem, Wireless communication features and LAN. It also provides tips on caring for your computer, floppy disks and CD/DVDs. TOSHIBA Dual Pointing Device The computer is equipped with a dual point system: a Touch Pad and an AccuPoint pointing stick.
Operating Basics Two buttons below the Touch Pad are used like the buttons on a mouse pointer. Press the left button to select a menu item or to manipulate text or graphics designated by the pointer. Press the right button to display a menu or other function depending on the software you are using. You can also tap the Touch Pad to perform functions similar to those of the left button. Click: Tap once Double-click: Tap twice Drag and drop: Tap to select the material you want to move.
Operating Basics Replacing the cap The AccuPoint cap is an expendable item that should be replaced after prolonged use. One spare AccuPoint cap is supplied with the computer. 1. To remove the AccuPoint cap, firmly pinch the cap and pull it straight up. Removing the AccuPoint cap 2. Position a new cap on the peg and press it into place. The peg is square, so be careful to align the cap’s square hole with the peg.
Operating Basics Using the USB floppy disk drive (optional) An optional USB floppy disk drive connects to any of the computer’s USB ports. It accommodates 1.44-megabyte or 720-kilobyte floppy disks. Refer to Chapter 2, The Grand Tour, for more information. Connecting USB floppy disk drive To connect the drive, plug the floppy disk drive’s USB connector into a computer’s USB port. Make sure the connector is right side up and properly aligned with the socket.
Operating Basics Changing Slim Select Bay modules This section explains how to change modules in the Slim Select Bay. The illustrations show replacement of the optical media drive with the Slim Select Bay HDD adaptor. Therefore, the text refers to those modules. However, the procedures are the same for any of the modules: DVD-ROM drive, DVD-ROM&CD-R/RW drive, DVD±R/±RW drive, DVD Super Multi drive, HDD adaptor, Slim Select Bay 2nd battery pack with separate tray.
Operating Basics 6. Grasp the optical media drive and slide it out. The optical media drive and other Slim Select Bay modules can become hot with use. Be careful when removing the module. Lock screw Slim Select Bay latch Optical media drive Removing the optical media drive Inserting a module Insert the Slim Select Bay HDD adaptor as described below. 1. Insert the Slim Select Bay HDD adaptor in the computer as shown below and press until the ejector clicks. 2.
Operating Basics Using optical media drives The text and illustrations in this section refer primarily to the optional media drive. However, operation is the same for other optical drive in the Slim Select Bay. The full-size drive provides high-performance execution of CD/DVD-ROM-based programs. You can run either 12 cm (4.72") or 8 cm (3.15") CD/DVDs without an adaptor. An ATAPI interface controller is used for CD/DVD-ROM operation.
Operating Basics 2. Grasp the disc tray gently and pull until it is fully opened. Disc tray Pulling the disc tray open 3. Lay the CD/DVD, label side up, in the disc tray. Laser lens Inserting a CD/DVD When the disc tray is fully opened, the edge of the computer will extend slightly over the CD/DVD tray. Therefore, you will need to turn the CD/DVD at an angle when you place it in the disc tray. After seating the CD/DVD, however, make sure it lies flat, as shown in figure 4-8.
Operating Basics 4. Press gently at the center of the CD/DVD until you feel it click into place. The CD/DVD should lie below the top of the spindle, flush with the spindle base. 5. Push the center of the disc tray to close it. Press gently until it locks into place. If the CD/DVD is not seated properly when the disc tray is closed, the CD/DVD might be damaged. Also, the disc tray might not open fully when you press the eject button.
Operating Basics How to remove CD/DVD when the disk tray will not open Pressing the eject button will not open the disc tray when the computer power is off. If the power is off, you can open the disc tray by inserting a slender object (about 15 mm) such as a straightened paper clip into the eject hole just to the right of the eject button. Eject hole Manual release with the eject hole Turn off the power before you use the eject hole.
Operating Basics Before writing or rewriting Please observe the following points when you write or rewrite the data. ■ We recommend the following manufacturers of CD-R and CD-RW media. Media quality can affect write or rewrite success rates. CD-R: TAIYO YUDEN CO., LTD. MITSUBISHI CHEMICAL CORPORATION RICOH Co., Ltd. Hitachi Maxell Ltd. CD-RW: MITSUBISHI CHEMICAL CORPORATION RICOH Co., Ltd. The following special media recommend the next manufacturers.
Operating Basics When writing or rewriting Note the following when you write or rewrite a CD-R or CD-RW. ■ Always copy data from the HDD to the CD. Do not use cut-and-paste. The original data will be lost if there is a write error. ■ Do not perform any of the following actions: ■ Change users in the Windows XP operating system. ■ Operate the computer for any other function, including use of a mouse or Touch Pad, closing/opening the LCD panel. ■ Start a communication application such as a modem.
Operating Basics Important message (DVD Super Multi drive) Before you write or rewrite to CD-R/RW or DVD-R/-RW/+R/+RW/-RAM disc, read and follow all setup and operating instructions in this section. If you fail to do so, the DVD Super Multi drive may not function properly, and you may fail to write or rewrite, lose data or incur other damage.
Operating Basics Before writing or rewriting ■ Based on TOSHIBA's limited compatibility testing, we suggest the following manufacturers of CD-R/RW and DVD-R/+R/-RW/+RW/-RAM disc. However, in no event does TOSHIBA guarantee the operation, quality or performance of any disc. Disc quality can affect write or rewrite success rates. CD-R: TAIYO YUDEN CO., LTD. MITSUBISHI CHEMICAL CORPORATION RICOH Co., Ltd. Hitachi Maxell Ltd. CD-RW: (Multi-Speed and High-Speed) MITSUBISHI CHEMICAL CORPORATION RICOH Co., Ltd.
Operating Basics This drive cannot use discs that allow writing faster than 8 speed (DVD-R, DVD+R), 4 speed (DVD-RW, DVD+RW), 3 speed (DVD-RAM) ■ If the disc is poor in quality, dirty or damaged, writing or rewriting errors may occur. Be careful to check the disc for dirt or damage before you use it. ■ The actual number of rewrites to CD-RW, DVD-RW, DVD+RW or DVD-RAM is affected by the quality of the disc and the way it is used. ■ There are two types of DVD-R discs: authoring and general use discs.
Operating Basics ■ Do not use hard disk utilities, including those intended to enhance HDD access speed. They may cause unstable operation and data damage. ■ CD-RW (Ultra Speed +) media is not available. If used, data may be lost or damaged. ■ Write from the computer's HDD to the CD/DVD. Do not try to write from shared devices such as a LAN server or any other network device. ■ Writing with software other than RecordNow! and InterVideo WinDVD Creator Platinum are not recommended.
Operating Basics RecordNow! Basic for TOSHIBA Note the following limitations when you use RecordNow!: ■ DVD-Video cannot be created using RecordNow!. ■ DVD-Audio cannot be created using RecordNow!. ■ You cannot use RecordNow!'s “Audio CD for Car or Home CD Player” function to record music to the DVD-R/-RW or DVD+R/+RW disc. ■ Do not use the “Exact Copy” function of RecordNow! to copy DVD-Video and DVD-ROM with copyright protection.
Operating Basics Data Verification To verify that data is written or rewritten correctly, follow the steps below before you write or rewrite a Data CD/DVD. 1. Click the Options button ( ) on the RecordNow! Console to open the Options panels. 2. Select the Data in the left-side menu. 3. Mark the Verify data written to the disc after burning check box in the Data Options. Click the OK button.
Operating Basics When using WinDVD Creator Platinum You can record video back to your digital camcorder via i.LINK (IEEE1394) using WinDVD Creator Platinum. However, there is a case where its playback sound is choppy. 1. Click start and select the Control Panel. 2. Click the Performance and Maintenance icon in the Control Panel. 3. Click the System icon in the Performance and Maintenance window. 4. Click the Advanced tab in the System Properties window. 5.
Operating Basics Important information for use Note the following limitations when you write video DVD: 1. Editing digital video ■ Log in with Administrator rights to use WinDVD Creator. ■ Make sure that your computer is running on AC power when using WinDVD Creator. ■ Operate the computer at Full Power. Do not use power-saving features. ■ While you are editing DVD, you can display previews. However, if another application is running, the preview might not display properly.
Operating Basics 2. Before recording the video to DVD ■ When you record to DVD disc, please use only discs recommended by the Drive manufacturer. ■ Do not set the working drive to a slow device like a USB 1.1 hard disk drive or it will fail to write DVD. ■ Do not perform any of the following actions: • Operate the computer for any other function, including using a mouse or Touch Pad or closing/opening the LCD panel. • Bump or cause vibration to the computer.
Operating Basics Media care This section provides tips on protecting data stored on your CD/DVDs and floppy disks. Handle your media with care. The following simple precautions will increase the lifetime of your media and protect the data stored on them: CD/DVDs 1. Store your CD/DVDs in the container they came in to protect them and keep them clean. 2. Do not bend the CD/DVD. 3. Do not write on, apply a sticker to, or otherwise mar the surface of the CD/DVD that contains data. 4.
Operating Basics Sound System Using the microphone Your computer has a built-in microphone that can be used to record monaural sounds into your applications. It can also be used to issue voice commands to applications that support such functions. Since your computer has a built-in microphone and speaker, “howling” may be heard under certain conditions. Howling occurs when sound from the speaker is picked up in the microphone and amplified back to the speaker, which amplifies it again to the microphone.
Operating Basics If the No Power Savings is selected, the audio controller always runs. If you want to a more effect for the power management, you can select another mode, the High Power Savings which can save the power than the Normal Power Savings. To select it, follow the steps below. 1. Click the Power Management tab. 2. Select the High Power Savings in the Power Mode pull-down list. 3. Input a time in Power Save Delay (Seconds).
Operating Basics To select a region, follow the steps below. 1. Click start, point to All Programs, point to TOSHIBA, point to Networking and click Modem Region Select. Do not use the Country/Region Select function in the Modem setup utility in the Control Panel if the function is available. If you change the Country/Region in the Control Panel, the change may not take effect. 2. The Region Selection icon will appear in the Windows Task Bar. 3.
Operating Basics Modem Selection If the computer cannot recognize the internal modem, a dialog box is displayed. Select the COM port for your modem to use. Dialing Properties Select this item to display the dialing properties. If you are using the computer in Japan, the Telecommunications Business Law requires that you select Japan region mode. It is illegal to use the modem in Japan with any other selection. Connecting To connect the modular cable, follow the steps below.
Operating Basics If you use a storage device such as an optical drive or HDD connected to a 16-bit PC card, you might experience the following modem problems: ■ Modem speed is slow or communication is interrupted. ■ Skips may occur in sound. Disconnecting To disconnect the internal modular cable, follow the steps below. 1. Pinch the lever on the connector in the telephone jack and pull out the connector. 2. Disconnect the cable from the computer’s modem jack in the same manner.
Operating Basics ■ The numerical values for display are the theoretical maximums for Wireless LAN standards. The actual values may differ. ■ The transmission speed over the wireless LAN and the distance over which wireless LAN can reach may vary depending on surrounding electromagnetic environment, obstacles, access point design and configuration, and client design and software/hardware configurations. The Transmit Rate (xx Mbit/s) is the theoretical maximum speed under the IEEE802.11 (a/b/g) standard.
Operating Basics BluetoothTM Stack for Windows® by TOSHIBA Please note that this software is specifically designed for the following operating systems: ■ Microsoft® Windows® 2000 Professional ■ Microsoft® Windows® XP Detailed information regarding the use with these operating systems is listed below. Please refer also to the electronic information which is included with each software. This BluetoothTM Stack is based on BluetoothTM Version 1.1/1.2 specification.
Operating Basics Wireless communication Indicator The wireless communication indicator indicates the status of the wireless communication functions. Indicator status Indication Indicator off Wireless communication switch is set to off. Automatic power down because of overheating. Power malfunction Indicator glows Wireless communication switch is on. Wireless LAN or Bluetooth is turned on by an application.
Operating Basics Connecting LAN cable To connect the LAN cable, follow the steps below. ■ Connect the AC adaptor before connecting the LAN cable. The AC adaptor must remain connected during LAN use. If you disconnect the AC Adaptor while the computer is accessing a LAN, the system may hang up. ■ Do not connect any other cable to the LAN jack except the LAN cable. Otherwise, malfunctions or damage may occur. ■ Do not connect any power supplying device to the LAN cable that is connected to the LAN jack.
Operating Basics Cleaning the computer To help ensure long, trouble-free operation, keep the computer free of dust and use care with liquids around the computer. ■ Be careful not to spill liquids into the computer. If the computer does get wet, turn the power off immediately and let the computer dry completely before you turn it on again. ■ Clean the computer using a slightly damp (with water) cloth. You can use glass cleaner on the LCD display screen.
Operating Basics Heat dispersal To protect from overheating, the CPU has an internal temperature sensor. If the computer’s internal temperature rises to a certain level, the cooling fan is turned on or the processing speed is lowered. You can select whether to control the CPU temperature by turning on the fan first, then if necessary, lowering the CPU speed. Or, by lowering the CPU speed first, then if necessary, turning on the fan. Use the Cooling Method item of the Basic Setup tab in TOSHIBA Power Saver.
Operating Basics 4-34 User’s Manual
TECRA M3 Chapter 5 The Keyboard The computer’s keyboard layouts are compatible with a 101/102-key enhanced keyboard. By pressing some keys in combination, all the 101/102-key keyboard functions can be executed on the computer. The number of keys on your keyboard depends on which country/region’s keyboard layout your computer is configured with. Keyboards for numerous languages are available.
The Keyboard Function keys: F1 … F12 The function keys (not to be confused with Fn) are the 12 keys at the top of your keyboard. These keys function differently from other keys. F1 through F12 are called function keys because they execute programmed functions when pressed. Used in combination with the Fn key, keys marked with icons execute specific functions on the computer. Refer to the section, Soft keys: Fn key combinations, in this chapter.
The Keyboard Press Fn + F10 or Fn + F11 to access the integrated keypad. When activated, the keys with gray markings on the bottom edge become numeric keypad keys (Fn + F11) or cursor control keys (Fn + F10). Refer to the Keypad overlay section in this chapter for more information on how to operate these keys. The power on default for both settings is off. Press Fn + F12 (ScrLock) to lock the cursor on a specific line. The power on default is off.
The Keyboard Instant security: Press Fn + F1 to blank the screen to prevent others from accessing your data. To restore the screen and original settings, press any key or press the Dual Pointing Device. If a screensaver password is registered, a dialog box will appear. Enter the screensaver password and click OK. If no password is set, the screen will be restored when you press any key or press the Dual Pointing Device. Power save mode: Pressing Fn + F2 changes the power save mode.
The Keyboard Display selection: Press Fn + F5 to change the active display device. When you press these hot keys, a dialog box appears. Only selectable devices will be displayed. Hold down Fn and press F5 again to change the device. When you release Fn and F5, the selected device will change. If you hold down these hot keys for five seconds the selection will return to the internal LCD. Internal LCD screen Brightness: Pressing Fn + F6 decreases the LCD screen brightness in decrements.
The Keyboard Dual Pointing Device: Pressing Fn + F9 in a windows environment enables or disables the Dual Pointing Device function. When you press these hot keys, the current setting will change and be displayed as an icon. LCD screen resolution selection: Press Fn + Space keys to change the display resolution. Each time when you press these hot keys, the LCD screen resolution changes as follows: The available resolution depends on the model.
The Keyboard Windows special keys The keyboard provides two keys that have special functions in Windows: Windows logo key activates the start menu and the other, the application key, has the same function as the secondary mouse button. This key activates the Windows start menu. This key has the same function as the secondary mouse button. Keypad overlay Your computer’s keyboard does not have an independent numeric keypad, but its numeric keypad overlay functions like one.
The Keyboard The numeric keypad overlay Temporarily using normal keyboard (overlay on) While using the overlay, you can temporarily access the normal keyboard without turning off the overlay: 1. Hold Fn and press any other key. All keys will operate as if the overlay were off. 2. Type upper-case characters by holding Fn + Shift and pressing a character key. 3. Release Fn to continue using the overlay.
The Keyboard Generating ASCII characters Not all ASCII characters can be generated using normal keyboard operation. But, you can generate these characters using their ASCII codes. With the overlay on: 1. Hold down Alt. 2. Using the overlay keys, type the ASCII code. 3. Release Alt, and the ASCII character appears on the display screen. With the overlay off: 1. Hold down Alt + Fn. 2. Using the overlay keys, type the ASCII code. 3. Release Alt + Fn, and the ASCII character appears on the display screen.
The Keyboard 5-10 User’s Manual
TECRA M3 Chapter 6 Power and Power-Up Modes The computer’s power resources include the AC adaptor, battery pack and internal batteries. This chapter gives details on making the most effective use of these resources including charging and changing batteries, tips for saving battery power, and power up modes.
Power and Power-Up Modes Table 6-1 Power conditions continued AC adaptor connected AC adaptor not connected Power on Power off (no operation) 2nd battery fully charged • Operates • No charge • LED: 2nd Battery green DC IN green • No charge • LED: 2nd battery green DC IN green 2nd Battery partially charged or no charge • Operates • Charge*2 • LED: 2nd battery orange DC IN green • Quick charge*2 • LED: 2nd battery orange DC IN green No 2nd battery installed • Operates • No charge • LED: 2nd batter
Power and Power-Up Modes Table 6-1 Power conditions continued Power on AC adaptor not connected 2nd battery charge is above low battery trigger point • Operates • LED: 2nd battery off DC IN off 2nd battery charge is below low battery trigger point • Operates • LED: 2nd battery flashes orange DC IN off 2nd battery charge is exhausted Computer shuts down *3 No 2nd battery is installed • No operation *5 • LED: 2nd battery off DC IN off Power off (no operation) 2nd battery indicator refers to the Sli
Power and Power-Up Modes Power indicators As shown in the above table, the Battery, Slim Select Bay, DC IN and Power indicators on the system indicator alert you to the computer’s operating capability and battery charge status. Battery indicators Check the Battery indicator to determine the status of the main battery and the Slim Select Bay indicator to determine the status of the 2nd battery. The following indicator lights indicate the battery status: Flashing orange The battery charge is low.
Power and Power-Up Modes Power indicator Check the Power indicator to determine the power status: Green Indicates power is being supplied to the computer and the computer is turned on. Blinking orange Indicates power is being supplied to the computer while the computer is in Standby mode. The indicator turns on for one second and off for two seconds. No light Under any other conditions, the indicator does not light.
Power and Power-Up Modes To ensure that the battery pack maintains its maximum capacity, operate the computer on battery power at least once a month until the battery pack is fully discharged. Refer to Extending battery life in this chapter for procedures. If the computer is continuously operated on AC power through an AC adaptor for an extended period, more than a month, the battery may fail to retain a charge.
Power and Power-Up Modes Safety precautions Mishandling of battery packs can cause death, serious injury or property damage. Carefully observe the following advisories: Danger: Indicates an imminently hazardous situation, which could result in death or serious injury, if you do not follow instructions. Warning: Indicates a potentially hazardous situation, which could result in death or serious injury, if you do not follow instructions.
Power and Power-Up Modes Warning 1. Never allow caustic electrolyte fluid leaked from a battery pack to contact your eyes, skin or clothing. If caustic electrolyte fluid should contact your eyes, immediately wash your eyes with large amounts of running water and seek medical attention, to help prevent eye damage. If electrolyte fluid should contact your skin immediately wash it under running water to prevent rash.
Power and Power-Up Modes Note 1. Never remove the battery pack while the Wake-up on LAN function is enabled. Data will be lost. Before you remove a battery pack, disable the Wake-up on LAN function. 2. To ensure the battery pack maintains maximum capacity, operate the computer on battery power once a week until the battery pack is fully discharged. Refer to the section Extending battery life in this chapter for procedures.
Power and Power-Up Modes Time The following table shows the approximate time required to fully charge a discharged battery. Charging time (hours) Battery type Power on Power off High capacity battery pack (8800mAh) about 9 to 21.5 about 4.5 Battery pack (4700mAh) about 5.5 to 13.0 about 3.0 2nd battery pack (3600mAh) about 4.0 to 9.5 about 3.0 RTC battery 8.
Power and Power-Up Modes Monitoring battery capacity Remaining battery power can be monitored in TOSHIBA Power Saver. ■ Wait at least 16 seconds after turning on the computer before trying to monitor the remaining operating time. The computer needs this time to check the battery’s remaining capacity and to calculate the remaining operating time, based on the current power consumption rate and remaining battery capacity. The actual remaining operating time may differ slightly from the calculated time.
Power and Power-Up Modes Retaining data with power off When you turn off your computer with fully charged batteries, the batteries retain data for the following approximate time periods: Retention time Battery type State and Retention Time High-capacity battery pack (8800mAh) about 11 days (Standby mode) about 80 days (Boot mode) Battery pack (4700mAh) about 6 days (Standby mode) about 40 days (Boot mode) 2nd battery pack (3600mAh) about 4 days about 30 days RTC battery 30 days Extending battery
Power and Power-Up Modes Replacing the battery pack When the battery pack reaches the end of its operating life you will need to install a new one. If the Battery indicator or Slim Select Bay indicator (if a Slim Select Bay 2nd battery pack is installed) flashes orange shortly after fully recharging the battery, the battery pack needs to be replaced. You might also replace a discharged battery pack with a charged spare when you are operating your computer away from an AC power source.
Power and Power-Up Modes 6. Slide and hold the battery release latch (➁) to disengage the battery pack, then remove the battery pack (➂). Battery pack Battery lock Battery release latch Releasing the battery pack 7. Return your computer to the upright position. For environmental reasons, do not throw away a spent battery pack. Please return spent battery packs to your TOSHIBA dealer. Installing the battery pack To install a battery pack, follow the steps below.
Power and Power-Up Modes 5. Secure the battery pack lock. Check the battery lock (➁) was changed to the lock position ( ). Battery pack Battery lock Securing the battery cover 6. Return your computer to the upright position. TOSHIBA Password Utility The TOSHIBA Password Utility provides two levels of password security: User and Supervisor. Passwords set in TOSHIBA Password Utility are different from the Windows password.
Power and Power-Up Modes User Password field ■ Set (button) Click this button to register a password of up to 50 characters. After a password is set, you will be prompted to enter it when you start the computer. ■ After you set the password, a dialog box will be displayed asking whether you want to save it to a floppy disk or other media. If you forget the password, you can open the password file on another computer. Be sure to keep the media in a safe place.
Power and Power-Up Modes ■ Disable (button) Click this button to invalidate the token. You cannot revalidate old tokens, but you can use the same SD cards to create new tokens. After using the token created for authentication, do not leave it inserted in the SD card slot, ensure that the token is removed from the slot and stored in a safe location.
Power and Power-Up Modes Power-up modes The computer has the following power-up modes: ■ Boot: Computer shuts down without saving data. Always save your work before you turn the computer off in boot mode. ■ Hibernation: Data in memory is saved to the hard disk. ■ Standby: Data is maintained in the computer’s memory. Refer also to the sections Turning on the power and Turning off the power in Chapter 3, Getting Started. Windows utilities You can specify the setting in TOSHIBA Power Saver.
TECRA M3 Chapter 7 HW Setup This chapter explains how to use TOSHIBA HW Setup program to configure your computer. TOSHIBA HW Setup lets you configure settings for General, Display, Boot Priority, Keyboard, CPU, LAN, Device Config, Parallel/Printer and USB. Accessing HW Setup To run HW Setup, click start, click Control Panel, click Printers and Other Hardware and select TOSHIBA HWSetup.
HW Setup General This window displays the BIOS version and contains two buttons: Default and About. Default Return all HW Setup values to the factory settings. About Display the HW Setup version. Setup This field displays BIOS Version and date. Display This tab lets you customize your computer’s display settings for either the internal LCD screen or for an external monitor.
HW Setup Boot Priority Boot Priority Options This option sets the priority for booting the computer. Select from the following settings: HDD −> FDD −> CD-ROM −> LAN The computer looks for bootable files in the following order: HDD, floppy disk drive*1, CD-ROM*2 and LAN (Default). FDD −> HDD −> CD-ROM −> LAN The computer looks for bootable files in the following order: floppy disk drive*1, HDD, CD-ROM*2 and LAN.
HW Setup To change the boot drive, follow the steps below. 1. Hold down F12 and boot the computer. 2. The following menu will be displayed with the following icons: Built-in HDD, Slim Select Bay HDD, CD-ROM, FDD (or SD memory card), Network (LAN) boot. A bar will appear only under the selected device. 3. Use the left/right cursor keys to highlight the boot device you want and press Enter. ■ If a supervisor password is set only, it is the following.
HW Setup HDD Priority Options If more than one HDD is installed in the computer, this option lets you set the priority for HDD detection. If the first detected HDD has a boot command, the system will boot from the HDD. Built-in HDD −> The computer will look for the Built-in HDD first, 2nd HDD (Default) next the 2nd HDD and then the HDD (Default). 2nd HDD −> Built-in HDD The computer will look for the 2nd HDD first, next the Built-in HDD and then the HDD.
HW Setup Wake-up on Keyboard When this feature is enabled and the computer is in Standby mode, you can turn on the computer by pressing any key. It is effective only for the internal keyboard and only when the computer is in standby mode. Enabled Enables the Wake-up on Keyboard. Disabled Disables the Wake-up on Keyboard (Default). CPU This function lets you set the CPU operating mode. It is displayed in Pentium-M® model only.
HW Setup Built-in LAN This feature enables or disables the Built-in LAN. Enabled Enables Built-in LAN functions (Default). Disabled Disables Built-in LAN functions. Device Config Device Configuration This option lets you set the device configuration. All Devices BIOS sets all devices. Setup by OS Operating system sets devices that it can control (Default). PCI Express Link ASPM This feature lets you set the PCI Express power-saving configuration.
HW Setup USB USB KB/Mouse Legacy Emulation Use this option to enable or disable USB KB/Mouse Legacy Emulation. If your operating system does not support USB, you can still use a USB mouse and keyboard by setting the USB KB/Mouse Legacy Emulation item to Enabled. Enabled Enables the USB KB/Mouse Legacy Emulation (Default). Disabled Disables the USB KB/Mouse Legacy Emulation. USB-FDD Legacy Emulation Use this option to enable or disable USB-FDD Legacy Emulation.
TECRA M3 Chapter 8 Optional Devices Optional devices can expand the computer’s capabilities and its versatility.
Optional Devices PC card The computer is equipped with a PC card slot that can accommodate a Type II card. Any PC card that meets industry standards (manufactured by TOSHIBA or other vendor) can be installed. The slot supports 16-bit PC cards, including PC card 16’s multifunction card and CardBus PC cards. CardBus supports the new standard of 32-bit PC cards. The bus provides superior performance for the greater demands of multimedia data transmission.
Optional Devices Removing a PC card To remove the PC card, follow the steps below. 1. Open the Safely Remove Hardware icon on the Task Bar. 2. Point to PC card and click. 3. Press the PC card eject button to extend it. If the PC card is not inserted all the way, the eject button may not pop out. Be sure to push the PC card firmly and press the eject button again. 4. Press the extended eject button to pop the card out slightly. 5. Grasp the PC card and draw it out.
Optional Devices 2. Press gently to ensure a firm connection. ExpressCard slot ExpressCard Inserting the ExpressCard 3. After inserting the ExpressCard, refer to the ExpressCard’s documentation and check the configuration in Windows to make sure it is appropriate for your ExpressCard. Removing an ExpressCard To remove the ExpressCard, follow the steps below. 1. Open the Safely Remove Hardware icon on the Task Bar. 2. Point to ExpressCard and click. 3. Press the ExpressCard eject button to extend it.
Optional Devices SD card The computer is equipped with an SD card slot that can accommodate Secure Digital flash memory cards with various memory capacities. SD cards let you easily transfer data from devices, such as digital cameras and Personal Digital Assistants, that use SD card flash-memory. The cards have a high level of security and copy protection features. The slot cannot accommodate Multi Media cards. Keep foreign objects out of the SD card slot.
Optional Devices 2. Press gently to ensure a firm connection. SD card slot SD card Inserting an SD card Make sure the SD card is oriented properly before you insert it. Removing an SD card To remove an SD card, follow the steps below. 1. Open the Safely Remove Hardware icon on the Task Bar. 2. Point to SD card and click. 3. Push in the SD card and release it to pop the card out slightly. 4. Grasp the SD card and remove it.
Optional Devices SD card care Set the write-protect switch to the lock position, if you do not want to record data. 1. Do not write to an SD card if the battery power is low. Low power could affect writing accuracy. 2. Do not remove an SD card while read/write is in progress. 3. The SD card is designed so that it can be inserted only one way. Do not try to force the SD card into the SD card slot. 4. Do not leave an SD card partially inserted in the slot.
Optional Devices ■ Use only memory modules approved by TOSHIBA. ■ Do not try to install or remove a memory module under the following conditions. You can damage the computer and the module. Also, data will be lost. a.The computer is turned on. b.The computer was shut down using the Standby mode or Hibernation mode. c.Wake-up on LAN is enabled. ■ Be careful not to let screws or other foreign matter fall into the computer. It could cause malfunction or electric shock.
Optional Devices 4. One screw in the position which removed the battery pack is removed. Screw Removing one screw 5. Return to your computer to the upright position. 6. Slide the display latch on the front of the computer to the right and open the LCD display panel. 7. Slip your finger under a notch at the end of the keyboard brace and lift up to release latches and remove the keyboard brace. Remove a keyboard brace after surely performing step 4.
Optional Devices 9. Lift up the back of the keyboard, rotate it toward you and lay in face down on the palm rest. ■ When you move the keyboard forward, do not touch the keys. Doing so could cause misalignment. Hold the keyboard by the sides and lay it gently on the palm rest. ■ The keyboard is connected to the computer by a ribbon cable. Be careful not to apply tension to this cable when you lift up the keyboard. Do not try to disconnect this cable. Rotate the keyboard 10.
Optional Devices 11. Fit the memory module's connectors into the socket at about a 45 degree angle and push the module down until latches on either side snap into place. Align the notch of the memory module with that of the memory slot and gently insert the module into the slot. Slot B Slot A Installing the memory module 12. The keyboard cable is pressed down with Metal brace and one screw secures the metal brace. 13.
Optional Devices 4. Push the latches to the outside to release the memory module. A spring will force one end of the memory module up. 5. Grasp the sides of the module and pull it out, then replace the insulator. ■ If you use the computer for a long time, the memory modules and the circuits locating close to the memory modules will become hot. In this case, let them cool to room temperature before you replace them. Or you will get burnt if you touch any of them.
Optional Devices Inserting To install the 2nd battery pack in the adaptor, follow the steps below. 1. Fit the side of the 2nd battery pack opposite the connector into the adaptor. 2. Lay the battery into the adaptor. The latch should close automatically to secure the 2nd battery pack. Inserting the 2nd battery pack in the adaptor Removing To remove the 2nd battery from the adaptor, follow the steps below. 1. Slide the latch in the direction of the arrow shown below. 2.
Optional Devices Battery charger The battery charger provides a convenient way to charge battery packs without requiring the use of your computer. The battery charger holds up to two battery packs (lithium ion). Hard disk drive pack An extra HDD expands the flexibility of your system and lets you carry your data without carrying the computer. Use a point size 0 Phillips screwdriver. Removing the HDD pack To remove the HDD pack, follow the steps below. 1.
Optional Devices 8. Lift the HDD pack and remove it. Plastic tab Removing the HDD pack Installing the HDD pack To install the HDD pack, follow the steps below. 1. Place the HDD into the space for HDD. Slide the HDD to connect to the connector. 2. Fold over the plastic tab so that it goes into the HDD space. Press the HDD to ensure a firm connection. Installing the HDD pack 3. Seat the cover and press down until the latches click into place. 4. Secure the cover with a screw. 5.
Optional Devices Slim Select Bay HDD adaptor (Black) You can increase your computer’s data storage capacity by installing an additional 40.0 billion bytes (37.26 GB), 60.0 billion bytes (55.89 GB), 80.0 billion bytes (74.53 GB) and 100.0 billion bytes (93.16 GB) hard disk drive in the Slim Select Bay. To install an HDD in the Slim Select Bay HDD adaptor follow the steps below. 1. Slide the lock to the unlock position and open the lid. Lock Lid Opening the lid 2.
Optional Devices 3. Close the lid and slide the lock to the lock position. Figure 8-20 Closing the lid For details on inserting the Slim Select Bay HDD adaptor in the computer’s Slim Select Bay slot, refer to Chapter 4, Operating Basics. USB floppy disk drive The USB floppy disk drive module can be connected to the USB port. For details on connecting the USB floppy disk drive module, refer to Chapter 4, Operating Basics.
Optional Devices However, the Windows Desktop appears on a display device that you used last time to shut down your computer, if the display device exists when you turn on the power. To change the display settings, press Fn + F5. If you disconnect the external monitor before you turn the computer’s power off, be sure to press Fn + F5 to switch to the internal display. Refer to Chapter 5, The Keyboard, for details on using hot keys to change the display setting.
Optional Devices If a television is connected to the computer, set the TV type in Display Properties. Follow the steps below. a. Click start and click Control Panel. b. Double-click the Display icon to open the Display Properties window. c. Click the Settings tab and click the Advanced button. d. Click the GeForce Go 6600 TE 64M/6200 TE 128M tab, click Device Settings and click Select TV format. e. Select Advanced and select TV Settings in the TV Settings window. f.
Optional Devices Even if the above does not set up, there are some as which the movies is simultaneously displayed depending on the type of the movies. d. Click OK. e. Click OK in the Display Properties screen. i.LINK (IEEE1394) i.LINK (IEEE1394) is used for high-speed data transfer for a range of compatible devices such as ■ Digital video cameras ■ Hard disk drives ■ MO drives ■ CD-RW drives i.LINK uses a four-pin connector, which does not carry electric current.
Optional Devices Connecting 1. Make sure the connectors are properly aligned and plug the i.LINK (IEEE1394) cable into the computer. i.LINK (IEEE1394) connector i.LINK (IEEE1394) port Connecting the i.LINK(IEEE1394) cable into the computer 2. Plug the other end of the cable into the device. Note the following when you use i.LINK: ■ You may need to install drivers for your i.LINK devices. ■ Not all i.LINK devices have been tested. Therefore, compatibility with all i.LINK devices cannot be guaranteed.
Optional Devices Advanced Port Replicator IIl In addition to the ports available on the computer, the Advanced Port Replicator lll provides serial port and separate ports for PS/2 mouse and PS/2 keyboard. The Advanced Port Replicator connects directly to the docking interface on the underside of the computer. The AC adaptor connects the Advanced Port Replicator to a power source. The computer must be configured properly before connecting to a LAN.
Optional Devices Parallel printer You can connect any standard Centronics-compatible parallel printer to your computer. All you need is an IBM PC™ parallel printer cable. Your dealer can supply one or you can purchase one at most computer stores. The cable’s connectors are designed so that it is impossible for you to connect them incorrectly. To connect a printer, follow these steps: 1. Turn off the computer’s power. 2. Connect the cable into the Advanced Port Replicator III’s parallel port. 3.
Optional Devices Security lock Security locks enable you to anchor your computer and optional Advanced Port Replicator III to a desk or other heavy object to help prevent unauthorized removal of the computer or Advanced Port Replicator III. The computer has a security lock slot on the left side. Attach one end of a cable to a desk and the other end to the security lock slot. 1. Turn the computer so the left side faces you. 2. Align the holes for the security lock and attach the lock.
TECRA M3 Chapter 9 Troubleshooting TOSHIBA designed the computer for durability. However, should problems occur, following the procedures in this chapter can help to determine the cause. All readers should become familiar with this chapter. Knowing what might go wrong can help prevent problems from occurring. Problem solving process Resolving problems will be much easier if you observe the following guidelines: ■ Stop immediately when you recognize a problem exists.
Troubleshooting Preliminary checklist Consider the simplest solution first. The items in this checklist are easy to fix and yet can cause what appears to be a serious problem. ■ Make sure you turn on all peripheral devices before you turn on the computer. This includes your printer and any other external device you are using. ■ Before you attach an external device, turn the computer off. When you turn the computer back on it recognizes the new device.
Troubleshooting Software Hardware The problems may be caused by your software or disk. If you cannot load a software package, the media may be damaged or the program might be corrupted. Try loading another copy of the software. If an error message appears while you are using a software package, check the software documentation. These documents usually include a problem solving section or a summary of error messages. Next, check any error messages in the OS documentation.
Troubleshooting Self test When the computer starts up, the self test will be run automatically, and the following will be displayed: S In Touch with Tomorrow TOSHIBA This message remains on the screen for a few seconds. If the self test is successful, the computer tries to load the operating system, depending on how the Boot Priority is set in the TOSHIBA HW Setup program.
Troubleshooting If the computer has reached room temperature and still does not start, or if it starts but shuts down quickly contact your dealer. Computer shuts down and its DC IN indicator is flashing in green Indicates a problem with the heat dispersal system. Please contact your dealer. AC power If you have trouble turning on the computer with the AC adaptor connected, check the DC IN indicator. Refer to Chapter 6, Power and Power-Up Modes for more information.
Troubleshooting Problem Procedure Battery doesn’t charge when the AC adaptor is attached (Battery or Slim Select bay indicator does not glow in orange.) If the battery is completely discharged, it will not begin charging immediately. Wait a few minutes. If the battery still does not charge, make sure the outlet of the AC adaptor is supplying power. Test it by plugging in an appliance. Check whether the battery is hot or cold to the touch.
Troubleshooting Real Time Clock Problem Procedure The following message is Displayed on the LCD screen: RTC battery is low or CMOS checksum is inconsistent. Press [F1] key to set Date/Time. The battery for RTC is wearing. Set the date and time in BIOS setup with the following steps: 1. Press F1 key. BIOS setup will boot up. 2. Set the date in System Date. 3. Set the time in System Time. 4. Press End key. Confirmation message will appear. 5. Press Y key.
Troubleshooting Internal LCD display panel Apparent LCD problems may be related to the computer’s setup. Refer to Chapter 7, HW Setup, for more information. Problem Procedure No display Press hotkeys Fn + F5 to change the display priority, to make sure it is not set for an external monitor. Markings appear on the They might have come from contact with the LCD screen. keyboard, Touch Pad. Try wiping the LCD screen gently with a clean dry cloth. If markings remain, use LCD screen cleaner.
Troubleshooting DVD-ROM drive For more information, refer to Chapter 4, Operating Basics Problem Procedure You cannot access a CD/ DVD in the drive Make sure the drive’s disc tray is securely closed. Press gently until it clicks into place. Check whether the drive power is on. If the power is off, click on the optical media drive icon in the task tray and turn on the power. Open the disc tray and make sure the CD/ DVD is properly seated. It should lie flat with the label facing up.
Troubleshooting DVD-ROM&CD-R/RW drive For more information, refer to Chapter 4, Operating Basics. Problem Procedure You cannot access a CD/DVD in the drive Make sure the drive’s disc tray is securely closed. Press gently until it clicks into place. Check whether the drive power is on. If the power is off, click on the optical media drive icon in the task tray and turn on the power. Open the disc tray and make sure the CD/DVD is properly seated. It should lie flat with the label facing up.
Troubleshooting Problem Procedure Cannot write correctly If you have trouble writing, make sure you are observing the following precautions: ■ Use only media recommended by TOSHIBA. ■ Do not use the mouse or keyboard during writing. ■ Use only the software supplied with the computer for recording. ■ Do not run or start other software during writing. ■ Do not jar the computer during writing. ■ Do not connect/disconnect external devices or install/remove internal cards during writing.
Troubleshooting Check the type of CD/DVD you are using. The drive supports: DVD-ROM: DVD-ROM, DVD-Video, DVD-R, DVD-RW, DVD+R, DVD+RW CD-ROM: CD-DA, CD-Text, Photo CDTM (single/multi-session), CD-ROM Mode 1, Mode 2, CD-ROM XA Mode 2 (Form1, Form2), Enhanced CD (CD-EXTRA), Addressing Method 2 Check the region code on the DVD. It must match that on the DVD±R/±RW drive. Region codes are listed in the Optical media drives section in Chapter 2, The Grand Tour.
Troubleshooting A foreign object in the disc tray could block laser light from reading the CD/DVD. Make sure there is no obstruction. Remove any foreign object. Check whether the CD/DVD is dirty. If it is, wipe it with a clean cloth dipped in water or a neutral cleaner. Refer to the Media care section in Chapter 4 for details on cleaning. Some CD/DVDs run The software or hardware configuration may be correctly, but others do causing a problem.
Troubleshooting SD card Refer also to Chapter 8, Optional Devices. Problem Procedure SD card error occurs Reseat the SD card to make sure it is firmly connected. Check the card’s documentation. You cannot write to an SD memory card Make sure the card is not write protected. You cannot read a file Make sure the target file is on the SD memory card inserted in the slot. If problems persist, contact your dealer. PC card Refer also to Chapter 8, Optional Devices.
Troubleshooting Infrared port Refer also to the documentation for your IrDA compatible device and related software. Problem Procedure Infrared devices do not work as expected Make sure there is no obstruction blocking communication between the computer and the target device. If problems persist, contact your dealer. TOSHIBA Dual Pointing Device If you are using a USB mouse, also refer to the USB section in this chapter and to your mouse documentation.
Troubleshooting Problem Procedure Double-tapping (Touch Pad) or doubleclicking (AccuPoint) does not work Try changing the double-click speed setting in the mouse control utility. 1. Click start, click Control Panel, click Printers and Other Hardware and select Mouse icon. 2. Click the Buttons tab. 3. Set the double-click speed as instructed and click OK. If problems persist, contact your dealer.
Troubleshooting USB Refer also to your USB device’s documentation. Problem Procedure USB device does not work Check for a firm cable connection between the USB ports on the computer and the USB device. Make sure the USB device drivers are properly installed. Refer to your Windows XP documentation for information on checking the drivers. If you are using an operating system that does not support USB, you can still use a USB mouse and/or USB keyboard.
Troubleshooting Sound system Refer also to documentation for your audio devices. Problem Procedure No sound is heard Adjust the volume control dial. Check the software volume settings. Make sure the headphone connection is secure. If problems persist, contact your dealer. Check Windows Device Manager.
Troubleshooting i.LINK (IEEE1394) Problem Procedure i.LINK device does not function Make sure the cable is securely connected to the computer and to the device. Make sure the device’s power is turned on. Reinstall the drivers. Open the Windows Control Panel and double-click the Add Hardware icon. Follow the on-screen directions. Restart Windows. If problems persist, contact your dealer.
Troubleshooting Problem Procedure Character display becomes garbled during a communication In data transmission, make sure the parity bit and stop bit settings correspond with those of the remote computer. Check the flow control and communication protocol. You cannot receive an incoming call Check the rings before auto answer setting in your communications application. You can also use the ATS0 command. If problems persist, contact your dealer.
Troubleshooting Bluetooth For more information on wireless communication, refer to Chapter 4, Operating Basics. Problem Procedure Cannot access Bluetooth device Make sure the computer’s wireless communication switch is set to on. Make sure the Bluetooth Manager is running and the power to the Bluetooth device is turned on. Make sure no optional Bluetooth PC card and Bluetooth SD card are installed in the computer.
Troubleshooting TV output signal Problem Procedure Display on TV is poor Make sure the TV type is correct for your area: NTSC (US, JAPAN), PAL (Europe). No display Try adjusting the contrast and brightness controls on the external monitor. Press hotkeys Fn + F5 to change the display. Refer to Chapter 5, The Keyboard. If problems persist, contact your dealer.
TECRA M3 Appendix A Specifications This appendix summarizes the computer’s technical specifications. Physical Dimensions Weight (typical) 2.26 kilograms, configured with: 14.1”XGA, 256MB RAM, 40GB HDD, DVD-ROM drive, modem, LAN (100M Bit), Wireless LAN, no Bluetooth antenna, 6cell battery pack. Weight will vary with other configurations. Above weights are measured at a specific criteria. They are not guaranteed as the maximum weight of the actual product. Size 314 (w) × 260 (d) × 31.5/34.
Specifications Power Requirements AC adaptor 100-240 volts AC 50 or 60 hertz (cycles per second) Computer 15 VDC 5.
Specifications User’s Manual Transmitting level -10 dBm Receiving level -10 to -40 dBm Input/output impedance 600 ohms ±30% Error correcting MNP class 4 and ITU-T V.42 Data compression MNP class 5 and ITU-T V.42bis Power supply +3.
Specifications A-4 User’s Manual
TECRA M3 Appendix B Display Controller and Modes Display controller The display controller interprets software commands into hardware commands that turn particular pels on or off. The display controller supports VGA, SVGA and XGA mods at internal LCD display panel. SXGA+ model supports SXGA and SXGA+ in addition to VGA, SVGA and XGA modes. ■ 14.1" XGA, 1024 horizontal × 768 vertical pixels ■ 14.
Display Controller and Modes Table1 Video modes (VGA) B-2 Video mode Type Resolution Character matrix (pels) Colors Scanning frequency Vertical (Hz) 0, 1 VGA Text 40 × 25 Characters 8×8 16 of 256K 70 2, 3 VGA Text 80 × 25 Characters 8×8 16 of 256K 70 0*, 1* VGA Text 40 × 25 Characters 8 × 14 16 of 256K 70 2*, 3* VGA Text 80 × 25 Characters 8 × 14 16 of 256K 70 0+, 1+ VGA Text 40 × 25 Characters 9 × 16 16 of 256K 70 2+, 3+ VGA Text 80 × 25 Characters 9 × 16 16 of 25
Display Controller and Modes Table1 Video modes (VGA) continued Video mode Type Resolution Character matrix (pels) Colors Scanning frequency Vertical (Hz) D VGA Grph 320 × 200 Pels 8×8 16 of 256K 70 E VGA Grph 640 × 200 Pels 8×8 16 of 256K 70 F VGA Grph 640 × 350 Pels 8 × 14 Mono 70 10 VGA Grph 640 × 350 Pels 8 × 14 16 of 256K 70 11 VGA Grph 640 × 480 Pels 8 × 16 2 of 256K 60 12 VGA Grph 640 × 480 Pels 8 × 16 16 of 256K 60 13 VGA Grph 320 × 200 Pels 8×8 256 of
Display Controller and Modes Table 2 Video modes (XGA model) Resolution LCD colors CRT colors Vertical frequency (Hz)* 640 × 480 256/256K 256/256K 60 75 85 100 800 × 600 256/256K 256/256K 60 75 85 100 1024 × 768 256/256K 256/256K 60 75 85 100 1280 × 1024 (Virtual with LCD only) 256/256K 256/256K 60 75 85 100 1600 × 1200 (Virtual with LCD only) 256/256K 256/256K 60 75 85 100 1920 × 1440 (Virtual with LCD only) 256/256K 256/256K 60 75 85 2048 × 1536 (Virtual with LCD only) 256/25
Display Controller and Modes Table 2 Video modes (XGA model) continued Resolution LCD colors CRT colors Vertical frequency (Hz)* 640 × 480 64K/64K 64K/64K 60 75 85 100 800 × 600 64K/64K 64K/64K 60 75 85 100 1024 × 768 64K/64K 64K/64K 60 75 85 100 1280 × 1024 (Virtual with LCD only) 64K/64K 64K/64K 60 75 85 100 1600 × 1200 (Virtual with LCD only) 64K/64K 64K/64K 60 75 85 100 1920 × 1440 (Virtual with LCD only) 64K/64K 64K/64K 60 75 85 2048 × 1536 (Virtual with LCD only) 64K/64K
Display Controller and Modes Table 2 Video modes (XGA model) continued Resolution LCD colors CRT colors Vertical frequency (Hz)* 640 × 480 16M/16M 16M/16M 60 75 85 100 800 × 600 16M/16M 16M/16M 60 75 85 100 1024 × 768 16M/16M 16M/16M 60 75 85 100 1280 × 1024 (Virtual with LCD only) 16M/16M 16M/16M 60 75 85 100 1600 × 1200 (Virtual with LCD only) 16M/16M 16M/16M 60 75 85 100 1920 × 1440 (Virtual with LCD only) 16M/16M 16M/16M 60 75 85 2048 × 1536 (Virtual with LCD only) 16M/16M
Display Controller and Modes Table 3 Video modes (SXGA+ model) Resolution LCD colors CRT colors Vertical frequency (Hz)* 640 × 480 256/256K 256/256K 60 75 85 100 800 × 600 256/256K 256/256K 60 75 85 100 1024 × 768 256/256K 256/256K 60 75 85 100 1280 × 1024 256/256K 256/256K 60 75 85 100 1400 × 1050 256/256K 256/256K 60 75 85 100 1600 × 1200 (Virtual with LCD only) 256/256K 256/256K 60 75 85 100 1920 × 1440 (Virtual with LCD only) 256/256K 256/256K 60 75 85 2048 × 1536 (Virtu
Display Controller and Modes Table 3 Video modes (SXGA+ model) continued Resolution LCD colors CRT colors Vertical frequency (Hz)* 640 × 480 64K/64K 64K/64K 60 75 85 100 800 × 600 64K/64K 64K/64K 60 75 85 100 1024 × 768 64K/64K 64K/64K 60 75 85 100 1280 × 1024 64K/64K 64K/64K 60 75 85 100 1400 × 1050 64K/64K 64K/64K 60 75 85 100 1600 × 1200 (Virtual with LCD only) 64K/64K 64K/64K 60 75 85 100 1920 × 1440 (Virtual with LCD only) 64K/64K 64K/64K 60 75 85 2048 × 1536 (Virtual w
Display Controller and Modes Table 3 Video modes (SXGA+ model) continued Resolution LCD colors CRT colors Vertical frequency (Hz)* 640 × 480 16M/16M 16M/16M 60 75 85 100 800 × 600 16M/16M 16M/16M 60 75 85 100 1024 × 768 16M/16M 16M/16M 60 75 85 100 1280 × 1024 16M/16M 16M/16M 60 75 85 100 1400 × 1050 16M/16M 16M/16M 60 75 85 100 1600 × 1200 (Virtual with LCD only) 16M/16M 16M/16M 60 75 85 100 1920 × 1440 (Virtual with LCD only) 16M/16M 16M/16M 60 75 85 2048 × 1536 (Virtual w
Display Controller and Modes B-10 User’s Manual
TECRA M3 Appendix C Wireless LAN Card Specifications Form Factor Mini PCI Type III Compatibility ■ IEEE 802.11 Standard for Wireless LANS ■ Wi-Fi (Wireless Fidelity) certified by the Wi-Fi Alliance. The ‘Wi-Fi CERTIFIED’ logo is a certification mark of the Wi-Fi Alliance. Network Operating System ■ Microsoft Windows® Networking Media Access Protocol ■ CSMA/CA (Collision Avoidance) with Acknowledgment (ACK) Data Rate ■ Theoretical maximum speed: 54Mbps(IEEE802.11a/ IEEE802.
Wireless LAN R-F Frequency ■ Band 5GHz (5150-5850 MHz) (Revision A, Turbo Mode) ■ Band 2.4GHz (2400-2483.5 MHz) (Revision B, G, Turbo Mode) Modulation Technique ■ DSSS-CCK, DSSS-DQPSK, DSSS-DBPSK (Revision B) ■ OFDM-BPSK, OFDM-QPSK, OFDM-16QAM, OFDM-64QAM (Revision A, G, Turbo Mode) The range of the wireless signal is related to the transmit rate of the wireless communication. Communications at lower transmit range may travel larger distances.
Wireless LAN 10 2457*1 11 2462 12 2467 13 2472 *1 Factory-set default channels When installing Wireless LAN cards, the channel configuration is managed as follows: ■ For wireless clients that operate in a Wireless LAN Infrastructure, the Wireless LAN card will automatically start operation at the channel identified by the Wireless LAN Access Point. When roaming between different access points the station can dynamically switch to another channel if required.
Wireless LAN 116 5580 120 5600 124 5620 128 5640 132 5660 136 5680 140 5700 149 5745 153 5765 157 5785 161 5805 165 5825 Wireless Channels Sets (Turbo Mode) Frequency Range Channel ID 2400-2483.
TECRA M3 Appendix D Bluetooth wireless technology Interoperability BluetoothTM Cards from TOSHIBA are designed to be interoperable with any product with Bluetooth wireless technology that is based on Frequency Hopping Spread Spectrum (FHSS) radio technology, and is compliant to: ■ Bluetooth Specification Ver.1.2, as defined and approved by The Bluetooth Special Interest Group. ■ Logo certification with Bluetooth wireless technology as defined by The Bluetooth Special interest Group.
Bluetooth wireless technology Interoperability ■ Bluetooth wireless technology is a new innovative technology, and TOSHIBA has not confirmed compatibility of its BluetoothTM products with all computers and/or equipment using Bluetooth wireless technology other than TOSHIBA portable computers. Always use BluetoothTM Cards from TOSHIBA in order to enable wireless networks over two or more (up to a total of seven) TOSHIBA portable computers using these cards.
Bluetooth wireless technology Interoperability Bluetooth wireless technology and your Health The products with Bluetooth wireless technology, like other radio devices, emit radio frequency electromagnetic energy. The level of energy emitted by devices with Bluetooth wireless technology however is far much less than the electromagnetic energy emitted by wireless devices like for example mobile phones.
Bluetooth wireless technology Interoperability L ‘ utilisation de ce dispositif est autorisée seulement aux conditions suivantes: (1) il ne doit pas produire de brouillage et (2) l’ utilisateur du dispositif doit étre prét à accepter tout brouillage radioélectrique reçu, même si ce brouillage est susceptible de compromettre le fonctionnement du dispositif. The term “IC” before the equipment certification number only signifies that the Industry Canada technical specifications were met.
Bluetooth wireless technology Interoperability (The model with embedded Wireless LAN module: PA3234U-1MPC) Relevant transmitters include FCC IDs: CJ6UPA3234WL, CJ6UPA3232BT (The model with embedded Wireless LAN module: PA3297U-1MPC) Relevant transmitters include FCC IDs: CJ6UPA3297WL, CJ6UPA3232BT (The model with embedded Wireless LAN module: PA3299U-1MPC) Relevant transmitters include FCC IDs: CJ6UPA3299WLP, CJ6UPA3232BT (The model with embedded Wireless LAN module: PA3362U-1MPC) Relevant transmitters inc
Bluetooth wireless technology Interoperability Using BluetoothTM Card from TOSHIBA equipment in Japan In Japan, the frequency bandwidth of 2,400~2,483.5 MHz for second generation low-power data communication systems such as this equipment overlaps that of mobile object identification systems (premises radio station and specified low-power radio station). 1. Sticker Please put the following sticker on computer incorporating this product.
Bluetooth wireless technology Interoperability 3. TOSHIBA Direct PC Monday - Friday: Toll Free Tel : Direct Dial : FAX : 10:00-17:00 0120-13-1100 03-3457-5916 03-5444-9450 Device Authorization This device obtains the Technical Regulation Conformity Certification and the Technical Conditions Compliance Approval, and it belongs to the device class of radio equipment of low-power data communication system radio station stipulated in the Radio Law and the Telecommunications Business of Japan.
Bluetooth wireless technology Interoperability Approved Countries/Regions for use (BluetoothTM wireless technology) BluetoothTM Card from TOSHIBA equipment is approved to the radio standard by the countries/regions in the following table. Do not use this equipment except in the countries/regions in the following table.
TECRA M3 Appendix E AC Power Cord and Connectors The power cord’s AC input plug must be compatible with the various international AC power outlets and the cord must meet the standards for the country/region in which it is used. All cords must meet the following specifications: Length: Minimum 2 meters Wire size: Minimum 0.75 mm2 Current rating: Minimum 2.5 amperes Voltage rating: 125 or 250 VAC (depending on country/region’s power standards) Certification agencies U.S.
AC Power Cord and Connectors For the United States and Canada, two pin plug configuration must be a 2-15P (250V) or 1-15P (125V) and three pin plug configuration must be 6-15P (250V) or 5-15P (125V) as designated in the U.S. National Electrical code handbook and the Canadian Electrical Code Part II. The following illustrations show the plug shapes for the U.S.A. and Canada, the United Kingdom, Australia and Europe.
TECRA M3 Appendix F If your computer is stolen Always take care of your computer and try to prevent it from being stolen. You are the owner of a valuable technical device, which may be highly attractive to thieves, so please do not leave it unattended in a public place. To further help protect against theft, security cables can be bought for use with your notebook when it is being used at home or in the office.
If your computer is stolen TOSHIBA Theft Registration Send to: Fax number: TOSHIBA Europe GmbH Technical Service and Support Leibnizstr. 2 93055 Regensburg Germany +49 (0) 941 7807 921 Country stolen: Machine type: (e.g. Satellite A50) Model number: (e.g. PSA50 YXT) Serial number: (e.g.
TECRA M3 Glossary The terms in this glossary cover topics related to this manual. Alternate naming is included for reference.
Glossary IrDA: Infrared Data Association IRQ: interrupt request KB: kilobyte LCD: liquid crystal display LED: light emitting diode LSI: large scale integration MB: megabyte MS-DOS: Microsoft Disk Operating System OCR: optical character recognition (reader) PCB: printed circuit board PCI: peripheral component interconnect RAM: random access memory RGB: red, green, and blue ROM: read only memory RTC: real time clock SCSI: small computer system interface SIO: serial input/output SXGA+: super extended graphics
Glossary analog signal: A signal whose characteristics such as amplitude and frequency vary in proportion to (are an analog of) the value to be transmitted. Voice communications are analog signals. ANSI: American National Standards Institute. An organization established to adopt and define standards for a variety of technical disciplines. For example, ANSI defined the ASCII standard and other information processing requirements. antistatic: A material used to prevent the buildup of static electricity.
Glossary bus: An interface for transmission of signals, data or electric power. byte: The representation of a single character. A sequence of eight bits treated as a single unit; also the smallest addressable unit within the system. C cache memory: High speed memory which stores data that increases processor speed and data transfer rate. When the CPU reads data from main memory, it stores a copy of this data in cache memory.
Glossary compatibility: 1) The ability of one computer to accept and process data in the same manner as another computer without modifying the data or the media upon which it is being transferred. 2) the ability of one device to connect to or communicate with another system or component. components: Elements or parts (of a system) which make up the whole (system). computer program: A set of instructions written for a computer that enable it to achieve a desired result.
Glossary delete: To remove data from a disk or other data storage device. Synonymous with erase. device driver: A program that controls communication between a specific peripheral device and the computer. The CONFIG.SYS file contains device drivers that MS-DOS loads when you turn the computer on. dialog box: A window that accepts user input to make system settings or record other information. disk drive: The device that randomly accesses information on a disk and copies it to the computer’s memory.
Glossary escape: 1) A code (ASCII code 27), signaling the computer that what follows are commands; used with peripheral devices such as printers and modems. 2) A means of aborting the task currently in progress. escape guard time: A time before and after an escape code is sent to the modem which distinguishes between escapes that are part of the transmitted data, and escapes that are intended as a command to the modem. execute: To interpret and execute an instruction.
Glossary hardware: The physical electronic and mechanical components of a computer system: typically, the computer itself, external disk drives, etc. See also software and firmware. hertz: A unit of wave frequency that equals one cycle per second. hexadecimal: The base 16 numbering system composed of the digits 0 through 9 and the letters A, B, C, D, E, and F. host computer: The computer that controls, regulates, and transmits information to a device or another computer.
Glossary J jumper: A small clip or wire that allows you to change the hardware characteristics by electrically connecting two points of a circuit. K K: Taken from the Greek word kilo, meaning 1000; often used as equivalent to 1024, or 2 raised to the 10th power. See also byte and kilobyte. KB: See kilobyte. keyboard: An input device containing switches that are activated by manually pressing marked keys. Each keystroke activates a switch that transmits a specific code to the computer.
Glossary mode: A method of operation, for example, the boot mode, standby mode or the hibernation mode. modem: Derived from modulator/demodulator, a device that converts (modulates) digital data for transmission over telephone lines and then converts modulated data (demodulates) to digital format where received. monitor: A device that uses rows and columns of pixels to display alphanumeric characters or graphic images. See also CRT.
Glossary P parallel interface: Refers to a type of information exchange that transmits information one byte (8 bits) at a time. See also serial interface. parity: 1) The symmetrical relationship between two parameter values (integers) both of which are either on or off; odd or even; 0 or 1. 2) In serial communications, an error detection bit that is added to a group of data bits making the sum of the bits even or odd. Parity can be set to none, odd, or even.
Glossary restart: Resetting a computer without turning it off (also called “warm boot” or “soft reset”). See also boot. RGB: Red, green, and blue. A device that uses three input signals, each activating an electron gun for a primary additive color (red, green, and blue) or port for using such a device. See also CRT. RJ11: A modular telephone jack. RJ45: A modular LAN jack. ROM: Read Only Memory: A nonvolatile memory chip manufactured to contain information that controls the computer’s basic operation.
Glossary T terminal: A typewriter-like keyboard and CRT display screen connected to the computer for data input/output. TFT display: A liquid crystal display (LCD) made from an array of liquid crystal cells using active-matrix technology with thin film transistor (TFT) to drive each cell. Touch Pad: A pointing device integrated into the TOSHIBA computer palm rest. TTL: Transistor-transistor logic. A logic circuit design that uses switching transistors for gates and storage.
Glossary Glossary-14 User’s Manual
TECRA M3 Index A AC adaptor 1-4, 2-17 additional 1-17, 8-13 connecting 3-4 DC IN 15V jack 2-6 Advanced Port Replicator III 1-17, 8-22 ASCII characters 5-9 B Battery 2nd 6-6 charging 6-9 extending life 6-12 indicator 2-11, 6-4 location 2-6 monitoring capacity 6-11 real time clock 1-3, 6-6 safety precautions 6-7 save mode 1-12 types 6-5 Battery charger 1-17, 8-14 Battery pack 1-3, 2-6 additional 8-12 replacing 6-13 Bluetooth 1-8, 4-28 problems 9-21 TOSHIBA Stack 1-14 Boot Priority 7-3 User’s Manual C CD-
Index DVD±R/±RW drive (DVD Dual drive) 1-5 location 2-4 problems 9-11 using 4-7 writing 4-12 DVD-ROM drive 1-4 location 2-4 problems 9-9 using 4-7 DVD-ROM&CD-R/RW drive 1-5 location 2-4 problems 9-10 using 4-7 writing 4-10 E Environment 3-1 Equipment checklist 1-1 Equipment setup general conditions 3-2 placement 3-2 Ergonomics lighting 3-3 seating and posture 3-3 work habits 3-4 ExpressCard 1-7, 8-3 inserting 8-3 location of slot 2-2 problems 9-14 removing 8-4 F Floppy disk care 4-22 Fn + Ctrl (enhanced
Index I M K Media care 4-22 CD/DVDs 4-22 floppy disks 4-22 SD card 8-7 Memory 1-3 expansion 1-17, 8-7 installing 8-8 problems 9-17 removing 8-11 Modem 1-8, 4-24 connecting 4-26 disconnecting 4-27 jack 2-5 problems 9-19 properties menu 4-25 region selection 4-24 Monitor external 1-6, 2-4, 8-17 problems 9-18 Moving the computer 4-32 i.
Index Power button location 2-8 conditions 6-1 hibernation mode 3-8 indicators 6-4 panel on/off 1-12, 6-18 problems 9-4 shut down mode (boot mode) 3-8 standby mode 3-10 system auto off 6-18 turning off 3-8 turning on 3-7 Power-up modes 6-18 Printer parallel 7-7, 8-23 Problems AC power 9-5 Analyzing symptoms 9-2 Battery 9-5 Bluetooth 9-21 Dual Pointing Device 9-15 DVD Multi drive 9-12 DVD Super Multi drive 9-12 DVD±R/±RW drive (DVD Dual drive) 9-11 DVD-ROM drive 9-9 DVD-ROM&CD-R/RW drive 9-10 ExpressCard 9-
Index Standby 1-13 setting 3-10 System automatic 1-11 T TOSHIBA Assist 1-15 TOSHIBA Assist button 1-11 TOSHIBA Controls 1-14 TOSHIBA Dual Pointing Device utility 1-15 TOSHIBA Mic Effect 1-15 TOSHIBA Mobile Extension 1-15 TOSHIBA PC Diagnostic Tool 1-15 TOSHIBA Power Saver 1-14 TOSHIBA Presentation button 1-11 TOSHIBA SD Memory Boot Utility 1-14 TOSHIBA Theft Registration F-2 TOSHIBA Zooming Utility 1-14 TV 8-18 User’s Manual U USB 1-6 location 2-4 problems 9-17 USB floppy disk drive 1-4 problems 9-13 us
Index Index-6 User’s Manual
