User’s Manual TECRA A9/ TECRA S5/ TECRA P5/ Satellite Pro S200
Table of Contents Copyright. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . vi Disclaimer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . vi Trademarks . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . vi FCC information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . vii EU Declaration of Conformity . . . . . . . . . . . . . . . .
TECRA A9/ TECRA S5/ TECRA P5/ Satellite Pro S200 Right side . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-4 Back . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-5 Underside . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-7 Front with the display open . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-8 Indicators . . . . . . . . . . . .
TECRA A9/ TECRA S5/ TECRA P5/ Satellite Pro S200 System Auto Off . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-13 Chapter 7 HW Setup & BIOS Setup Accessing HW Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-1 HW Setup window . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-1 BIOS Setup Program . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
TECRA A9/ TECRA S5/ TECRA P5/ Satellite Pro S200 Non-applicable Icons*1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . CPU*2. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Memory (Main System)*3 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Battery Life*4 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Hard Disk Drive (HDD) Capacity*5 . . . . . . . . . . . . . . . .
TECRA A9/ TECRA S5/ TECRA P5/ Satellite Pro S200 Copyright © 2007 by TOSHIBA Corporation. All rights reserved. Under the copyright laws, this manual cannot be reproduced in any form without the prior written permission of TOSHIBA. No patent liability is assumed, with respect to the use of the information contained herein.
TECRA A9/ TECRA S5/ TECRA P5/ Satellite Pro S200 FCC information FCC notice "Declaration of Conformity Information" This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
TECRA A9/ TECRA S5/ TECRA P5/ Satellite Pro S200 EU Declaration of Conformity TOSHIBA declares, that this product conforms to the following Standards: Supplementary Information: “The product complies with the requirements of the Low Voltage Directive 73/23/EEC, the EMC Directive 89/336/EEC and/or the R&TTE Directive 1999/5/EC.” This product is carrying the CE-Mark in accordance with the related European Directives.
TECRA A9/ TECRA S5/ TECRA P5/ Satellite Pro S200 Network Compatibility Statement This product is designed to work with, and is compatible with the following networks. It has been tested to and found to conform with the additional requirements conditional in EG 201 121.
TECRA A9/ TECRA S5/ TECRA P5/ Satellite Pro S200 Pursuant to FCC CFR 47, Part 68: When you are ready to install or use the modem, call your local telephone company and give them the following information: ■ The telephone number of the line to which you will connect the modem ■ The registration number that is located on the device The FCC registration number of the modem will be found on either the device which is to be installed, or, if already installed, on the bottom of the computer outside of the main s
TECRA A9/ TECRA S5/ TECRA P5/ Satellite Pro S200 Fax branding The Telephone Consumer Protection Act of 1991 makes it unlawful for any person to use a computer or other electronic device to send any message via a telephone fax machine unless such message clearly contains in a margin at the top or bottom of each transmitted page or on the first page of the transmission, the date and time it is sent and an identification of the business, other entity or individual sending the message and the telephone number
TECRA A9/ TECRA S5/ TECRA P5/ Satellite Pro S200 The Ringer Equivalence Number (REN) assigned to each terminal device provides an indication of the maximum number of terminals allowed to be connected to a telephone interface. The termination on an interface may consist of any combination of devices subject only to the requirement that the sum of the Ringer Equivalence Numbers of all the devices does not exceed 5. 3.
TECRA A9/ TECRA S5/ TECRA P5/ Satellite Pro S200 Notes for use of this device in New Zealand ■ The grant of a Telepermit for a device in no way indicates Telecom acceptance of responsibility for the correct operation of that device under all operating conditions. In particular the higher speeds at which this modem is capable of operating depend on a specific network implementation which is only one of many ways of delivering high quality voice telephony to customers.
TECRA A9/ TECRA S5/ TECRA P5/ Satellite Pro S200 ■ When used in the Auto Answer mode, the S0 register must be set with a value of 3 or 4. This ensures: ■ a person calling your modem will hear a short burst of ringing before the modem answers. This confirms that the call has been successfully switched through the network. ■ caller identification information (which occurs between the first and second ring cadences) is not destroyed. ■ The preferred method of dialing is to use DTMF tones (ATDT...
TECRA A9/ TECRA S5/ TECRA P5/ Satellite Pro S200 The Telepermit label may also be shown on the packaging of the product and in the sales literature, as required in PTC 100. The charge for a Telepermit assessment is $337.50. An additional charge of $337.50 is payable where an assessment is based on reports against non-Telecom New Zealand Specifications. $112.50 is charged for each variation when submitted at the same time as the original. An invoice for $NZ1237.50 will be sent under separate cover.
TECRA A9/ TECRA S5/ TECRA P5/ Satellite Pro S200 Optical disc drive safety instructions Be sure to check the international precautions at the end of this section. Panasonic DVD-ROM&CD-R/RW UJDA780 ■ The DVD-ROM&CD-R/RW drive employs a laser system. To ensure proper use of this product, please read this instruction manual carefully and retain for future reference. Should the unit ever require maintenance, contact an authorized service location.
TECRA A9/ TECRA S5/ TECRA P5/ Satellite Pro S200 DVD Super Multi with Double Layer Recording UJ-860 ■ The DVD Super Multi drive with Double Layer Recording model employs a laser system. To ensure proper use of this product, please read this instruction manual carefully and retain for future reference. Should the unit ever require maintenance, contact an authorized service location.
TECRA A9/ TECRA S5/ TECRA P5/ Satellite Pro S200 TEAC CD-ROM CD-224E ■ The CD-ROM drive employs a laser system. To ensure proper use of this product, please read this instruction manual carefully and retain for future reference. Should the unit ever require maintenance, contact an authorized service location. ■ Use of controls, adjustments or the performance of procedures other than those specified may result in hazardous radiation exposure.
TECRA A9/ TECRA S5/ TECRA P5/ Satellite Pro S200 DVD-ROM&CD-R/RW drive DW-224E ■ The DVD-ROM&CD-R/RW drive employs a laser system. To ensure proper use of this product, please read this instruction manual carefully and retain for future reference. Should the unit ever require maintenance, contact an authorized service location. ■ Use of controls, adjustments or the performance of procedures other than those specified may result in hazardous radiation exposure.
TECRA A9/ TECRA S5/ TECRA P5/ Satellite Pro S200 DVD Super Multi with Double Layer Recording DV-W28EC ■ The DVD Super Multi drive with Double Layer Recording model employs a laser system. To ensure proper use of this product, please read this instruction manual carefully and retain for future reference. Should the unit ever require maintenance, contact an authorized service location.
TECRA A9/ TECRA S5/ TECRA P5/ Satellite Pro S200 International precautions CAUTION: This appliance contains a laser system and is classified as a “CLASS 1 LASER PRODUCT.” To use this model properly, read the instruction manual carefully and keep this manual for your future reference. In case of any trouble with this model, please contact your nearest “AUTHORIZED service station.” To prevent direct exposure to the laser beam, do not try to open the enclosure.
TECRA A9/ TECRA S5/ TECRA P5/ Satellite Pro S200 OBS! Apparaten innehåller laserkomponent som avger laserstråining överstigande gränsen för laserklass 1. VAROITUS. Suojakoteloa si saa avata. Laite sisältää laserdiodin, joka lähetää näkymätöntä silmilie vaarallista lasersäteilyä. CAUTION: USE OF CONTROLS OR ADJUSTMENTS OR PERFORMANCE OF PROCEDURES OTHER THAN THOSE SPECIFIED IN THE OWNER’S MANUAL MAY RESULT IN HAZARDOUS RADIATION EXPOSURE.
Preface Congratulations on your purchase of the TECRA A9/ TECRA S5/ TECRA P5/ Satellite Pro S200 series computer. This powerful notebook computer provides excellent expansion capability, includes multimedia functionality, and is designed to provide years of reliable, high-performance computing. This manual tells how to set up and begin using your TECRA A9/ TECRA S5/ TECRA P5/ Satellite Pro S200 computer.
TECRA A9/ TECRA S5/ TECRA P5/ Satellite Pro S200 Icons Icons identify ports, dials, and other parts of your computer. The indicator panel also uses icons to identify the components it is providing information on. Keys The keyboard keys are used in the text to describe many computer operations. A distinctive typeface identifies the key top symbols as they appear on the keyboard. For example, ENTER identifies the ENTER key. Key operation Some operations require you to simultaneously use two or more keys.
TECRA A9/ TECRA S5/ TECRA P5/ Satellite Pro S200 Terminology This term is defined in this document as follows: Start User’s Manual The word "Start" refers to the " Microsoft® Windows VistaTM.
General Precautions TOSHIBA computers are designed to optimize safety, minimize strain and withstand the rigors of portability. However, certain precautions should be observed to further reduce the risk of personal injury or damage to the computer. Be certain to read the general precautions below and to note the cautions included in the text of the manual.
TECRA A9/ TECRA S5/ TECRA P5/ Satellite Pro S200 Heat injury ■ Avoid prolonged physical contact with the computer. If the computer is used for long periods, its surface can become very warm. While the temperature will not feel hot to the touch, if you maintain physical contact with the computer for a long time, for example if you rest the computer on your lap or if you keep your hands on the palm rest, your skin might suffer a low-heat injury.
Chapter 1 Getting Started This chapter provides an equipment checklist, and basic information to start using your computer. Some of the features described in this manual may not function properly if you use an operating system that was not pre-installed by TOSHIBA. Equipment checklist Carefully unpack your computer, taking care to save the box and packaging materials for future use.
Getting Started Software The following Windows® operating system and utility software are preinstalled.
Getting Started Getting Started ■ All users should be sure to read the section Starting up for the first time. ■ Be sure to read the enclosed Instruction Manual for Safety and Comfort for information on the safe and proper use of this computer. It is intended to help you be more comfortable and productive while using a notebook computer. By following the recommendations in it you may reduce your chance of developing a painful or disabling injury to your hand, arms, shoulders or neck.
Getting Started Connecting the AC adaptor Attach the AC adaptor when you need to charge the battery or you want to operate from AC power. It is also the fastest way to get started, because the battery pack will need to be charged before you can operate from battery power. The AC adaptor can be connected to any power source supplying from 100 to 240 volts and 50 or 60 hertz. For details on using the AC adaptor to charge the battery pack, refer to Chapter 6, Power and Power-Up Modes.
Getting Started 1. Connect the power cord to the AC adaptor. Figure 1-1 Connecting the power cord to the AC adaptor (2-pin plug) Figure 1-2 Connecting the power cord to the AC adaptor (3-pin plug) Either a 2-pin or 3-pin adaptor/cord will be included with the computer depending on the model. 2. Connect the AC adaptor’s DC output plug to the DC IN 15V jack on the back of the computer. DC IN 15V jack Figure 1-3 Connecting the adaptor to the computer 3.
Getting Started Opening the display The display panel can be opened to a wide range of angles for optimal viewing. 1. Slide the display latch on the front of the computer to unlatch the display panel. 2. While holding down the palm rest with one hand so that the main body of the computer is not raised, slowly lift the display panel - this will allow the angle of the display panel to be adjusted to provide optimum clarity.
Getting Started Turning on the power This section describes how to turn on the power - the Power indicator will then indicate the status. Please refer to the Monitoring of power condition section in Chapter 6, Power and Power-Up Modes for more information. ■ After you turn on the power for the first time, do not turn it off until you have set up the operating system. Please refer to the section Starting up for the first time for more information. ■ Volume cannot be adjusted during Windows Setup. 1.
Getting Started ■ Make sure the Hard Disk Drive indicator is off. If you turn off the power while a disk (disc) is being accessed, you may lose data or damage the disk. ■ Never turn off the power while an application is running. Doing so may cause loss of data. ■ Never turn off the power, disconnect an external storage device or remove storage media during data read/write. Doing so may cause data loss. 3. Click Start. 4.
Getting Started Turning off your computer where electronic devices are regulated or controlled. When you have to turn off your computer aboard an aircraft or in places where electronic devices are regulated or controlled, always shut down the computer completely or put the computer into hibernation mode instead of allowing it to go into Standby Mode (Sleep Mode) and turn off any wireless communication switches or devices.
Getting Started When you turn the power back on, you can continue where you left when you shut down the computer. ■ When the computer is in Sleep Mode, the power indicator will blink orange. ■ If you are operating the computer on battery power, you can lengthen the overall operating time by turning it off with Hibernation Mode Sleep Mode will consume more power while the computer is off.
Getting Started Starting Hibernation Mode You can also enable Hibernation Mode by pressing FN + F4 - please refer to Chapter 5, The Keyboard, for further details. To enter Hibernation Mode, follow the steps below. 1. Click Start. 2. Click the arrow button ( ( ) in the power management buttons ) and select Hibernate from the menu. Automatic Hibernation Mode The computer can be configured to enter Hibernation Mode automatically when you press the power button or close the lid.
Getting Started ■ Press the power button and hold it down for five seconds. Once the computer has turned itself off, wait between ten and fifteen seconds before turning the power on again by pressing the power button. System Recovery Options About 1.5GB hidden partition is allocated on the hard disk drive for the System Recovery Options. This partition stores files which can be used to repair the system in the event of a problem.
Getting Started System Recovery This section describes the creation of Recovery Discs and their use. Creating Optical Recovery Discs This section describes how to create Recovery Discs. ■ Be sure to connect the AC adaptor when you create Recovery Discs. ■ Be sure to close all other software programs except the Recovery Disc Creator. ■ Do not run software such as screen savers which can put a heavy load on the CPU. ■ Operate the computer at full power. ■ Do not use power-saving features.
Getting Started If your optical disc drive can only write CDs, select 'CD' as the 'Disc Set' within the Recovery Disc Creator application. Otherwise, if your optical disc drive can write both CDs and DVDs, select the type of media you wish to create. Restoring the pre-installed software from the Recovery hard disk drive A portion of the total hard disk drive space is configured as a hidden recovery partition.
Getting Started Restoring the pre-installed software from your created Recovery Discs If the pre-installed files are damaged, you are able to either use the Recovery Discs you have created or the hard disk drive recovery process to restore the computer to the state it was in when you originally received it.
Chapter 2 The Grand Tour This chapter identifies the various components of the computer - it is recommended that you become familiar with each before you operate the computer. Legal Footnote (Non-applicable Icons)*1 For more information regarding Non-applicable Icons, please refer to the Legal Footnotes section in Appendix K or click the *1 above. Front with the display closed The following figure shows the computer’s front with its display panel in the closed position.
The Grand Tour System indicators These LED indicators allow you to monitor the status of various computer functions and are described in more detail within the System indicators section. Microphone A built-in microphone allows you to record sound into your applications - please refer to the Sound System section in Chapter 4, Operating Basics for more information. Only some models are equipped with the built-in microphone. Microphone jack A 3.
The Grand Tour Left side The following figure shows the computer’s left side. Serial port Cooling vents Universal Serial Bus (USB 2.0)ports PC Card eject button i.LINK (IEEE1394) port PC Card slot Bridge media slot Figure 2-2 The left side of the computer Serial port Use this 9-pin port to connect serial devices such as an external modem, serial mouse or serial printer. Only some models are equipped with the serial port. Cooling vents The cooling vents help keep the processor from overheating.
The Grand Tour i.LINK (IEEE1394) port This port allows you to connect an external device, such as a digital video camera for highspeed data transfer. Only some models are equipped with the iLINK port. Bridge media slot This slot lets you insert an SD/SDHC Card, Mini/Micro SD Card, Memory Stick (PRO/PRO Duo), xD picture card and MultiMediaCard. Refer to Chapter 3, Hardware, Utilities and Options. Keep foreign metal objects, such as screws, staples and paper clips, out of the Bridge media slot.
The Grand Tour Back The following figure shows the computer’s back. Modem jack DC IN 15V jack Security lock slot LAN active indicator (orange) LAN jack Link indicator (green) External monitor port Figure 2-4 The back of the computer Security lock slot A security cable can be attached to this slot and then connected to a desk or other large object in order to deter theft of the computer. Modem jack The modem jack lets you use a modular cable to connect the modem directly to a telephone line.
The Grand Tour DC IN 15V jack The AC adaptor connects to this jack in order to power the computer and charge its internal batteries. Please note that you should only use the model of AC adaptor supplied with the computer at the time of purchase - using the wrong AC adaptor can cause damage to the computer. LAN jack This jack lets you connect to a LAN.
The Grand Tour Underside The following figure shows the underside of the computer. You should ensure that the display is closed before the computer is turned over to avoid causing any damage. Notch Battery lock Battery pack Battery release latch Notch Docking port Memory module slot Figure 2-5 The underside of the computer Battery lock Slide the battery lock to release the battery pack ready for removal.
The Grand Tour Memory module slot The Slot A and Slot B memory modules are located here. The memory module slots allow for the installation, replacement and removal of memory modules. Refer to the Additional memory module section in Chapter 3, Hardware, Utilities and Options. Battery pack The battery pack provides power to the computer when the AC adaptor is not connected. For more detailed information on the use and operation of the battery pack please refer to Chapter 6, Power and Power-Up Modes.
The Grand Tour User’s Manual Display hinges The display hinges allow the display panel to be position at a variety of easy-to-view angles. Display screen Please be aware that, when the computer is operating on the AC adaptor, the image displayed on the internal screen will be somewhat brighter than when it operates on battery power. This difference in brightness levels is intended to save power when running on batteries.
The Grand Tour Power button Press this button to turn the computer's power on and off. TOSHIBA Assist button Press this button to launch the program automatically. When power-off, Sleep Mode and Hibernation Mode, press this button to start the computer and launch the program. Only some models are equipped with TOSHIBA Assist button. TOSHIBA Presentation button The TOSHIBA Presentation button has the same functionality as the Connect display button in the Mobility Center.
The Grand Tour Indicators This section explains indicator functions. System indicators LED system indicators next to their respective icons, glow when specific computer operations are in progress. Figure 2-7 System indicators User’s Manual Media slot The Media slot indicator glows green when the computer is accessing the Bridge media slot. DC IN The DC IN indicator normally glows green when power is being correctly supplied from the AC power adaptor.
The Grand Tour Keyboard indicators The following figures show the positions of the CAPS LOCK indicator and the keypad overlay indicators which show the following conditions: ■ When the CAPS LOCK indicator glows, the keyboard will produce capitals when any letter is typed. ■ When the Arrow Mode indicator glows, the keypad overlay allows you to use cursor functions. ■ When the Numeric Mode indicator glows, the keypad overlay allows you to enter numbers.
The Grand Tour Optical disc drives The computer is installed with either a CD-ROM, DVD-ROM&CD-R/RW or DVD Super Multi drive. An ATAPI interface controller is used for CD/DVDROM operation. When the computer is accessing a CD/DVD, an indicator on the drive glows. For information on loading and unloading discs refer to the Using optical disc drives section in Chapter 4, Operating Basics.
The Grand Tour DVDs ■ DVD-R and DVD+R discs can be written only once. The recorded data cannot be erased or changed. ■ DVD-RW, DVD+RW and DVD-RAM discs can be recorded more than once. Formats The drives support the following formats. CD-ROM drive The drive supports the formats CD-DA, CD-Text, Photo CD™ (single/ multisession), CD-ROM Mode1, Mode2, CD-ROM XA Mode2 (Form1, Form2), Enhanced CD (CD-EXTRA) and Addressing Method 2.
The Grand Tour The read speed is slower at the center of a disc and faster at the outer edge. DVD read 8 speed (maximum) CD read 24 speed (maximum) CD-R write 24 speed (maximum) CD-RW write 24 speed (maximum, Ultra-speed media) DVD Super Multi drive Double Layer The full-size DVD Super Multi drive module lets you record data to rewritable CD/DVDs as well as run either 12 cm (4.72") or 8cm (3.15") CD/DVDs without using an adaptor.
The Grand Tour Figure 2-10 The AC adaptor (2-pin plug) Figure 2-11 The AC adaptor (3-pin plug) ■ Depending on the model in question, either a 2-pin or 3-pin adaptor/power lead will be bundled with the computer. ■ Do not use a 3-pin to 2-pin conversion plug. ■ The supplied power cord conforms to safety rules and regulations in the region the product is bought and should not be used outside of this region.
Chapter 3 Hardware, Utilities and Options Hardware This section describes the hardware of your computer. The actual specifications may vary depending on the model you purchased. Processor CPU The computer is equipped with one of the following Intel® processors. ■ Intel® CoreTM 2 Duo Processor, which incorporates a 2MB level2 cache memory. It also supports Enhanced Intel® SpeedStep® Technology. ■ Intel® CoreTM 2 Duo Processor, which incorporates a 4MB level2 cache memory.
Hardware, Utilities and Options Memory Slots 256, 512, 1,024 or 2,048MB memory modules can be installed in the computer's two memory slots for a maximum of 4,096MB system memory. Video RAM The amount of Video RAM available is dependent on the computer's system memory. Start -> Control Panel -> Appearance and Personalization -> Personalization -> Display Settings. The amount of Video RAM can be verified by clicking the Advanced Settings... button in the Display Settings window.
Hardware, Utilities and Options Disks Hard disk drive This computer is equipped with one of the following hard disk drive types. The capacity of each hard disk drive model is different. ■ 60.0 billion bytes (55.89 GB) ■ 80.0 billion bytes (74.53 GB) ■ 120.0 billion bytes (111.79 GB) ■ 160.0 billion bytes (149.05 GB) Please note that part of the hard disk drive's overall capacity is reserved as administration space.
Hardware, Utilities and Options Graphics controller The graphics controller maximizes display performance. Refer to Display Controller and Video mode section in Appendix B for more information. Legal Footnote (Graphics Processor Unit ("GPU"))*7 For more information regarding the Graphics Processor Unit ("GPU"), please refer to the Legal Footnotes section in Appendix K or click the *7 above.
Hardware, Utilities and Options Wireless LAN Some computers in this series are equipped with a Wireless LAN card that is compatible with other LAN systems based on Direct Sequence Spread Spectrum/Orthogonal Frequency Division Multiplexing radio technology that complies with the IEEE 802.11 Standard (Revision A, B, G or N Draft Ver. 1.0). Legal Footnote (Wireless LAN)*8 For more information regarding Wireless LAN, please refer to the Legal Footnotes section in Appendix K or click the *8 above.
Hardware, Utilities and Options System automatic Sleep/Hibernation Mode *1 This feature automatically shuts down the system into either Sleep Mode or Hibernation Mode when there is no input or hardware access for a specified time. This can be specified in the Power Options. Keypad overlay A ten-key numeric keypad is integrated into the keyboard. Please refer to the Keypad overlay section in Chapter 5, The Keyboard, for information on using this feature.
Hardware, Utilities and Options Heat dispersal *1 To protect against overheating, the processor has an internal temperature sensor so that, if the computer's internal temperature rises to a certain level, the cooling fan is turned on or the processing speed is lowered. This can be specified in the Power Options.
Hardware, Utilities and Options TOSHIBA Value Added Package This section describes the TOSHIBA Component features pre-installed on the computer. TOSHIBA Power Saver TOSHIBA Power Saver provides you with the features of more various power supply managements. TOSHIBA Button Support This utility controls the following computer button functions. ■ TOSHIBA Assist ■ TOSHIBA Presentation The starting application from the button can be changed.
Hardware, Utilities and Options User’s Manual HW Setup This utility allows you to customize your hardware settings according to the way you work with the computer and the peripherals you use. TOSHIBA Accessibility The TOSHIBA Accessibility utility provides support to movement impaired users when they need to use the TOSHIBA Hot-key functions.
Hardware, Utilities and Options Utilities and Applications This section describes the pre-installed utilities that come with the computer and details how to start them. For further information on their operation, please refer to each utility's online manual, help files or README.TXT file.
Hardware, Utilities and Options Bluetooth Stack for Windows by Toshiba This software enables communication between the computer and external Bluetooth devices such as printers and mobile phones. Bluetooth functions cannot be used in models that do not have a Bluetooth module installed. TOSHIBA SD Memory Boot Utility The TOSHIBA SD memory boot utility allows you to create a bootable SD memory card to start the system. You can boot TOSHIBA SD Memory Boot Utility from the menu bar as follows.
Hardware, Utilities and Options User’s Manual TOSHIBA DVD-RAM Utility This utility has the function of Physical Format and Write-Protect to DVD-RAM. This utility is contained the setup module of TOSHIBA Disc Creator. To start this utility, click Start -> All Programs -> TOSHIBA -> CD&DVD Applications -> DVD-RAM Utility. CD/DVD Drive Acoustic Silencer This utility allows you to configure the read speed of the optical disc drive.
Hardware, Utilities and Options Optional devices Optional devices can expand the computer's capabilities and its versatility.
Hardware, Utilities and Options Do not insert a PC Card while the computer is in Sleep Mode or Hibernation Mode as you may find that some cards do not work properly. To insert a PC Card, follow the steps as detailed below: 1. Insert the PC Card into the PC Card slot on the side of the computer. 2. Press the PC Card gently to ensure a firm connection is made. PC Card slot PC Card Figure 3-1 Inserting the PC Card 3.
Hardware, Utilities and Options 5. Grasp the PC Card and remove it. PC Card PC Card eject button Figure 3-2 Removing the PC Card Bridge media slot The computer is equipped with a Bridge media slot that can accommodate some kinds of memory media with various memory capacities so that you can easily transfer data from devices, such as digital cameras and Personal Digital Assistants. ■ This Bridge media slot supports the following memory media.
Hardware, Utilities and Options Keep foreign objects out of the Bridge media slot. Never allow metal objects, such as screws, staples and paper clips, to enter the computer or keyboard. Foreign metal objects can create a short circuit, which can cause computer damage and fire, possibly resulting in serious injury. Memory card care ■ Memory media have a limited lifespan, so it is important to backup important data. ■ Do not write to memory media if the battery power is low.
Hardware, Utilities and Options Set the write-protect switch to the lock position, if you do not want to record data. Formatting an SD/SDHC memory card SD/SDHC memory cards are sold already formatted in conformity to specific standards. If you format the SD/SDHC Card again, be sure to format it with the TOSHIBA SD Memory Card Format utility, not with the format command provided within Windows.
Hardware, Utilities and Options ■ Make sure memory media is oriented properly before you insert it. If you insert the media in wrong direction, you may not be able to remove it. ■ Always use a Memory Stick Duo adaptor when inserting a Memory Stick PRO Duo into the slot. If you insert a Memory Stick PRO Duo without the adaptor, you may not be able to remove it. ■ When inserting memory media, do not touch the metal contacts. You could expose the storage area to static electricity, which can destroy data.
Hardware, Utilities and Options Additional memory module This computer is equipped with two memory slots; Slot A and Slot B. Both slots are located in the underside of the computer. You can install additional memory into the computer in order to increase the amount of system memory that is available. This section describes how to install and remove optional memory modules.
Hardware, Utilities and Options In all instances you should shut down the computer and remove the incompatible module(s). Use a point size 0 Phillips screwdriver to remove and fasten the screws the use of an incorrect screwdriver can damage the screw heads. Installing a memory module (Slot A and Slot B) The computer contains slots for two memory modules, one positioned immediately over the other - the procedures are the same for installing either module. 1.
Hardware, Utilities and Options 6. Align the notch of the memory module with that of the memory slot and gently insert the module into the slot at about a 45 degree angle before holding it down until the latches on either side snap into place. Slot B Slot A Modem module Figure 3-7 Seating the memory module ■ Never allow metal objects, such as screws, staples and paper clips, to enter the computer.
Hardware, Utilities and Options Screw Memory module cover Figure 3-8 Seating the memory module cover 8. Install the battery pack - refer to Replacing the battery pack section in Chapter 6, Power and Power-Up Modes, if required. 9. Turn your computer over. 10. Turn the computer on and make sure the added memory is recognized to confirmed it, Start -> Control Panel -> System and Maintenance -> System icon.
Hardware, Utilities and Options Latches Slot A Slot B Figure 3-9 Removing the memory module 8. Seat the memory module cover in place and secure it with one screw. Take care to ensure that the memory module cover is firmly closed. 9. Install the battery pack - refer to Replacing the battery pack section in Chapter 6, Power and Power-Up Modes, if required. 10. Turn your computer over.
Hardware, Utilities and Options 2. Connect the monitor cable to the external monitor port. External monitor port Monitor cable Figure 3-10 Connecting the monitor cable to the external monitor port 3. Turn the external monitor's power on. 4. Turn the computer's power on. When you turn on the power, the computer will automatically recognize the monitor and determine whether it is a color or monochrome device.
Hardware, Utilities and Options Connecting the USB floppy diskette drive To connect the drive, plug the floppy diskette drive’s USB connector into a computer’s USB port. Make sure the connector is properly aligned with the socket. Do not try to force the connection, doing so can damage the connecting pins.
Hardware, Utilities and Options i.LINK (IEEE1394) i.LINK (IEEE1394) is used for high-speed data transfer for a range of compatible devices such as: ■ Digital video cameras ■ Hard disk drives ■ MO drives ■ Writable optical disc drives i.LINK uses a four-pin connector, which does not carry any electric current. External devices will need their own power supply to operate. Precautions ■ Make a back-up of your data before transferring it to the computer.
Hardware, Utilities and Options Connecting 1. Make sure the connectors are properly aligned and plug the i.LINK (IEEE1394) cable into the computer. i.LINK (IEEE1394) port i.LINK (IEEE1394) connector Figure 3-13 Connecting the i.LINK (IEEE1394) cable into the computer 2. Plug the other end of the cable into the device. Note the following when you use i.LINK: ■ You may need to install drivers for your i.LINK devices. ■ Not all i.LINK devices have been tested. Therefore, compatibility with all i.
Hardware, Utilities and Options Serial port The serial connector can be used to connect to RS-232C compatible devices. RS-232C compatible devices include the following: ■ Modem ■ Mouse ■ Printer To connect a serial port, follow the steps as detailed below: 1. Turn the computer’s power off. 2. Connect the serial connector to the serial port and tighten the screws on the left and right hand side.
Hardware, Utilities and Options The following ports are available on the TOSHIBA Express Port Replicator. ■ RJ45 LAN jack ■ External monitor port ■ DC IN 15V jack ■ Security lock slot ■ Universal Serial Bus 2.0 port (four) ■ DVI port ■ Serial port ■ As the port operation of all DVI (Digital Visual Interface) monitors has not been confirmed, some DVI monitors may not function properly.
Hardware, Utilities and Options Optional accessories You are able to add a number of options and accessories in order to make your computer even more powerful and convenient to use. For reference, the following list details some of the items that are available from your reseller or TOSHIBA dealer: User’s Manual DDR2-667 Memory Module A 256MB, 512MB, 1,024MB or 2,048MB memory module (DDR2-667) can be easily installed in the computer.
Chapter 4 Operating Basics This chapter describes the basic operations of your computer, highlights the precautions that should be taken when using it. TOSHIBA Dual Pointing Device The computer is equipped with a dual point system: a Touch Pad and an AccuPoint pointing stick. Using the Touch Pad To use the Touch Pad, simply touch and move your fingertip across it in the direction you want the on-screen pointer to go.
Operating Basics You can also tap the Touch Pad to perform functions similar to those of the left button on a standard mouse. Click: Tap once Double-click: Tap twice Drag and drop: Tap twice to select the item(s) you want to move. Move the item(s) to the new desitination and then leave your finger on the Touch Pad. Using the AccuPoint To use the AccuPoint, simply push it with your finger tip in the direction you want to move the on-screen pointer.
Operating Basics Replacing the cap The AccuPoint cap is an expendable item that should be replaced after prolonged use. The spare AccuPoint cap is supplied with the computer. 1. To remove the AccuPoint cap, firmly pinch the cap and pull it straight up. AccuPoint cap Figure 4-2 Removing the AccuPoint cap 2. Position a new cap on the peg and press it into place. The peg is square, so be careful to align the cap’s square hole with the peg.
Operating Basics How to Swipe your Finger Using the following steps when swiping fingers for fingerprint registration or authentication will help to minimize authentication failures: Align the first joint of the finger at the center of the sensor, then lightly touch the sensor and swipe finger horizontally towards you until the sensor surface becomes visible. In performing this process, you should also take care to ensure that the center of your fingerprint is on the sensor.
Operating Basics ■ Do not touch the sensor with a finger or any other object which may have a build-up of static electricity on it. Observe the following before you place your finger on the sensor whether for fingerprint enrollment/registration or recognition. ■ Wash and dry your hands thoroughly. ■ Remove static electricity from your fingers by touching any metal surface. Static electricity is a common cause of sensor failures, especially when the weather is dry.
Operating Basics How to Delete the Fingerprint Data Saved fingerprint data is stored in special non-volatile memory inside the fingerprint sensor. Therefore, if you give the computer to someone else, or dispose of it in any way, the following process is recommended to delete your fingerprint information: 1. To run this program, click Start -> All Programs -> Protector Suite QL -> Control Center. 2. The Protector Suite Software screen is displayed. 3. Click Fingerprints and click Delete. 4.
Operating Basics If both the fingerprint sensor and Trusted Platform Module (TPM) security are used as identification devices, you must install and configure the Infineon TPM Professional package first before you setup and configure the fingerprint utility. Please refer to the TPM (Trusted Platform Module) Installation Guide for further information on the installation and configuration considerations relating to TPM.
Operating Basics 7. At the User's Fingers screen, select the finger that you wish to enroll from the illustration and then click Next. On this screen please be aware that any previously enrolled fingerprints would have green check marks, while the fingerprint that you are about to enroll will have a red check mark. If any of the previously enrolled fingerprints is selected again, the latest information will be enrolled and any previous information over-written. 8.
Operating Basics ■ You must ensure that you use the TOSHIBA Password Utility to register a User Password before using the Fingerprint Power-on Security and its extended function to allow fingerprints to be used to access the computer when it is turned on.
Operating Basics Only one fingerprint authentication is required to replace the User/BIOS Password (and, if applicable, the HDD(Hard Disk Drive) Password) and the Windows Logon Password. How to Enable Fingerprint Single Sign-on Feature It is necessary to first enroll your fingerprint with the Protector Suite QL application prior to enabling and configuring the Fingerprint Single Sign-on feature.
Operating Basics Loading discs To load CD/DVDs, follow the steps below. 1. When the computer’s power is on, press the eject button to open the disc tray slightly. 2. Grasp the disc tray gently and pull until it is fully opened. Disc tray Figure 4-4 Pressing the eject button and pulling the disc tray open 3. Lay the CD/DVD, label side up, in the disc tray. Laser lens Figure 4-5 Inserting a CD/DVD When the disc tray is fully opened, the edge of the computer will extend slightly over the CD/DVD tray.
Operating Basics ■ Do not touch the laser lens or any portion of its surrounding casing as this could cause misalignment. ■ Prevent foreign objects from entering the drive. Check the surface of the disc tray, especially the area behind the front edge of the disc tray, to make sure there are no such objects before closing the drive. 4. Press gently at the center of the CD/DVD until you feel it click into place. The CD/DVD should lie below the top of the spindle, flush with the spindle base. 5.
Operating Basics 2. The CD/DVD extends slightly over the sides of the disc tray so you can grasp it. Gently lift out the CD/DVD. Figure 4-7 Removing a CD/DVD 3. Push the center of the disc tray to close it. Press gently until it locks into place. How to remove CD/DVD when the disc tray will not open Pressing the eject button will not open the disc tray when the computer power is off.
Operating Basics Writing CDs on DVD-ROM&CD-R/RW drive Depending on the type of drive installed, you may be able to write CDs. The DVD-ROM&CD-R/RW drive lets you write as well as read CD-ROMs. Observe the precautions in this section to ensure the best performance for writing CDs. For information on loading and unloading CDs refer to the Media care section. ■ Refer to the Writable discs, Chapter 2 for the details about the types of writable CD/DVD discs.
Operating Basics ■ Be sure to close all other software programs except the writing software. ■ Do not run software such as a screen saver which can put a heavy load on the CPU. ■ Operate the computer at its full power setting - do not use any powersaving features. ■ Do not write information while virus checking software is running, instead waiting for it to finish, then disable the virus protection applications, including any software that checks files automatically in the background.
Operating Basics Writing CD/DVDs on DVD Super Multi drives You can use the DVD Super Multi drive to write data to either CD-R, CDRW, DVD-R, DVD-R (Dual Layer), DVD-RW, DVD+R, DVD+R (Double Layer), DVD+RW or DVD-RAM discs. The TOSHIBA Disc Creator is provided for writing. ■ Please refer to the Writable discs, Chapter 2 for details about the types of writable CD and DVD discs that can be supported by this computer.
Operating Basics Before writing or rewriting ■ Based on TOSHIBA's limited compatibility testing, we suggest the following manufacturers of CD-R, CD-RW, DVD-R, DVD-R (Dual Layer), DVD-RW, DVD+R, DVD+R (Double Layer), DVD+RW or DVDRAM media, however, it must be noted that disc quality can affect write or rewrite success rates. Please also be aware that in no event does TOSHIBA guarantee the operation, quality or performance of any disc. CD-R: TAIYO YUDEN CO., LTD. MITSUBISHI CHEMICAL CORPORATION RICOH Co.
Operating Basics DVD+RW: MITSUBISHI CHEMICAL CORPORATION RICOH Co., Ltd. DVD-RAM: (DVD Super Multi drive only) DVD Specifications for DVD-RAM Disc for Version 2.0, Version 2.1 or Version 2.2 Matsushita Electric Industrial Co., Ltd. Hitachi Maxell Ltd. ■ This drive cannot use discs that allow writing faster than 16x speed (DVD-R and DVD+R media), 8x speed (DVD-R (Dual Layer), DVD+RW and DVD+R (Double Layer) media), 6x speed (DVD-RW media), 5x speed (DVD-RAM media).
Operating Basics ■ Since the disc is based on the DVD standard, it might be filled with dummy data if the written data is less than about 1GB. Therefore, in these circumstance, even if you write only a small amount of data, it might take additional time to fill in the dummy data. ■ When multiple drives that can write data to discs are connected, be sure that you do not write to or delete data from the wrong drive.
Operating Basics ■ ■ ■ ■ ■ ■ Install, remove or connect external devices, including such items as a PC Card, SD Card, SDHC card, Memory Stick/ Memory Stick PRO/Memory Stick PRO Duo, xD picture card, MultiMediaCard, USB devices, external monitor, i.LINK devices, or optical digital devices. ■ Use the audio/video control button to reproduce music or voice. ■ Open the optical disc drive. Do not use shut down, log off, Sleep Mode or Hibernation Mode functions while writing or rewriting.
Operating Basics ■ You might not be able to use the 'Disc Backup' function of TOSHIBA Disc Creator to back up a DVD-R, DVD-R (Dual Layer), DVD-RW, DVD+R, DVD+R (Double Layer) or DVD+RW disc that was made with other software on a different optical media recorder. ■ If you add data to a DVD-R, DVD-R (Dual Layer), DVD+R or DVD+R (Double Layer) disc that you have already recorded to, you might not be able to read the added data under some circumstances.
Operating Basics Media care This section provides tips on protecting data stored on your CD's, DVD's and floppy diskettes. Handle your media with care. Following the simple precautions listed below will increase the lifetime of your media and protect the data stored on it. CD/DVDs 1. Store your CD's and DVD's in the containers they originally came in to protect them and keep them clean. 2. Do not bend the CD's or DVD's. 3.
Operating Basics 8. Data may be lost if the floppy diskette is twisted, bent, or exposed to direct sunlight, extreme heat or cold. 9. Do not place heavy objects on your floppy diskettes. 10. Do not eat, smoke, or use items such as erasers near your floppy diskettes as foreign particles inside the jacket of the floppy diskette can damage the magnetic surface. 11. Magnetic energy can destroy the data on your floppy diskettes.
Operating Basics Audio Enhancements In order to apply the sound effects for your current speaker, follow the steps below. 1. Right click on the speaker icon on the taskbar, and select Playback Devices from the sub menu. 2. Select Speakers, and click Properties. 3. On the Enhancement tab select the sound effects you would like, and click Apply. Realtek HD Audio Manager The Realtek HD Audio Manager provides you a user interface to change various audio configuration settings.
Operating Basics TOSHIBA Mic Effect TOSHIBA Mic Effect provides you with a hands-free environment for holding mutual communication via the Internet Protocol or Local Area Network. If you wish to communicate with someone on your computer, you can use a messenger application. However, with such an application, you would hear your own voice returning to you as echo during the communication if you did not use a headset system or headphone. TOSHIBA Mic Effect will reduce these echoes generated on your computer.
Operating Basics Region selection Telecommunication regulations vary from one region to another, so you will need to make sure the internal modem’s settings are correct for the region in which it will be used. The built-in modem can be used only in specified countries and regions. Using the modem in an area not specified for use may cause a system failure. Check the specified areas carefully before using it. To select a region, follow the steps as detailed below: 1.
Operating Basics Location list for region selection. Displays a sub-menu appears which details location information. Open dialog box, if the modem and Telephony Current Location region code do not match. Displays a warning if the current settings for both region code and telephony location are different. Modem Selection If the computer cannot recognize the internal modem, a dialog box is displayed from which you should select the appropriate communications port for your modem to use.
Operating Basics 2. Plug the other end of the modular cable into a telephone jack. Modular cable Modem jack Telephone jack Figure 4-9 Connecting the internal modem Do not pull on the cable or move the computer while the cable is connected. If you use a storage device such as an optical drive or hard disk drive connected to a 16-bit PC Card, you might experience the following problems with the operation of the modem: ■ The modem speed is slow or communication is periodically interrupted.
Operating Basics Wireless communications The computer’s wireless communication function supports both Wireless LAN and Bluetooth devices. Only some models are equipped with both Wireless LAN and Bluetooth functions. ■ Do not use the Wireless LAN (Wi-Fi) or Bluetooth functionalities near a microwave oven or in areas subject to radio interference or magnetic fields. Interference from a microwave oven or other source can disrupt Wi-Fi or Bluetooth operation.
Operating Basics ■ Wi-Fi Protected Access (WPA) ■ The values shown above are the theoretical maximums for Wireless LAN standards. The actual values may differ. ■ The transmission speed over the wireless LAN, and the distance over which the wireless LAN can reach, may vary depending on surrounding electromagnetic environment, obstacles, access point design and configuration, client design and software/hardware configurations.
Operating Basics Radio links You can easily establish links between two or more devices, with these links being maintained even if the devices are not within a line-of-sight of each other. Security Two advanced security mechanisms ensure a high level of security: ■ Authentication prevents access to critical data and makes it impossible to falsify the origin of a message. ■ Encryption prevents eavesdropping and maintains link privacy.
Operating Basics Wireless communication Indicator The wireless communication indicator shows the status of the computer's wireless communication functions. Indicator status Indication Indicator off The wireless communication switch is off - no wireless functionality is available. Indicator glows Wireless communication switch is on. Wireless LAN or Bluetooth is turned on by an application.
Operating Basics Connecting the LAN cable To connect the LAN cable, follow the steps as detailed below: ■ Connect the AC adaptor before connecting the LAN cable. The AC adaptor must remain connected during LAN use. If you disconnect the AC Adaptor while the computer is accessing a LAN, the system may hang up. ■ Do not connect any other cable to the LAN jack except the LAN cable. Otherwise, malfunctions or damage may occur.
Operating Basics Disconnecting the LAN cable To disconnect the LAN cable, follow the steps as detailed below: Make sure the LAN Active indicator (orange LED) is out before you disconnect the computer from the LAN. 1. Pinch the lever on the connector in the computer’s LAN jack and pull out the connector. 2. Disconnect the cable from the LAN hub or router in the same manner. Check with your LAN administrator and hardware or software vendor before disconnecting from the hub.
Operating Basics ■ Disconnect the AC adaptor and all peripherals before moving the computer. ■ Close the display panel. ■ Do not pick up the computer by its display panel. ■ Before carrying your computer, shut it down, disconnect the AC adaptor and allow it to cool down - a failure to follow this instruction may result in minor heat injury. ■ Be careful not to subject the computer to impact or shock - a failure to follow this instruction could result in damage to computer, computer failure or loss of data.
Operating Basics TOSHIBA HDD Protection Properties You can change the TOSHIBA HDD Protection settings by using the TOSHIBA HDD Protection Properties window. To open the window, click Start -> All Programs -> TOSHIBA -> Utilities -> HDD Protection Setting. The window can also be started from the icon on the Taskbar or from the Control Panel. HDD Protection You can choose whether to enable or disable TOSHIBA HDD Protection. Detection Level This function can be set to four levels.
Operating Basics Detection Level Amplification When the AC adaptor is disconnected or the lid is closed, HDD Detection assumes that the computer will be carried and sets the detection level to the maximum for 10 seconds. TOSHIBA HDD Protection Message Specify whether to display a message when TOSHIBA HDD Protection is active. ■ This function does not work when the computer is starting, in Sleep Mode, in Hibernation Mode, in transition to Hibernation Mode, recovering from Hibernation Mode, or powered off.
Chapter 5 The Keyboard The computer's keyboard layouts are compatible with a 104/105-key enhanced keyboard - by pressing some keys in combination, all of the 104/105-key enhanced keyboard functions can be performed on the computer. The number of keys available on your keyboard will depend on which country/region your computer is configured for, with keyboards being available for numerous languages.
The Keyboard Function keys: F1 … F12 The function keys (not to be confused with the special FN key) are the twelve keys at the top of your keyboard - these keys function differently from other keys. F1 through F12 are called function keys because they execute programmed functions when pressed and, when used in combination with the FN key, those keys marked with icons also execute specific functions on the computer.
The Keyboard Press FN + F10 or FN + F11 to access the computer's integrated keypad. When activated, the keys with grey markings on their bottom edge become either numeric keypad keys (FN + F11) or cursor control keys (FN + F10). Please refer to the Keypad overlay section in this chapter for more information on how to operate these keys, taking care to note that the power on default for both settings is off. Press FN + F12 (ScrLock) to lock the cursor on a specific line. The power on default is off.
The Keyboard Sleep: Pressing FN + F3 switches the system to Sleep Mode. Hibernate: Pressing FN + F4 switches the system to Hibernation Mode. Output: Pressing FN + F5 changes the active display device. Brightness Down: Pressing FN + F6 decreases the computer's display panel brightness in individual steps. Brightness Up: Pressing FN + F7 increases the computer's display panel brightness in individual steps.
The Keyboard TOSHIBA Zooming Utility (reduce): Pressing FN + 1 reduces the icon size on the desktop or the font sizes within one of the supported application windows. TOSHIBA Zooming Utility (enlarge): Pressing FN + 2 enlarges the icon size on the desktop or the font sizes within one of the supported application windows. FN Sticky key You can use the TOSHIBA Accessibility Utility to make the FN key sticky, that is, you can press it once, release it, and then press an "F number" key.
The Keyboard Arrow mode To turn on Arrow Mode, press FN + F10 - the Arrow mode indicator lights and you are able to access cursor and page control functions by using the keys. You are able to press FN + F10 again to turn off this overlay function. Numeric mode To turn on Numeric Mode, press FN + F11 - the Numeric Mode indicator lights and you are able to access numeric characters by using the keys. You are able to press FN + F11 again to turn off this overlay function.
The Keyboard Temporarily using overlay (overlay off) While using the normal keyboard function, you can temporarily use the keypad overlay without having to turn it on: 1. Hold down FN key. 2. Check the keyboard indicators as pressing the FN key will turn on the most recently used overlay function - if the Numeric Mode indicator lights you can use the overlay for numeric entry, while if the Arrow Mode indicator lights, you can use the overlay for cursor and page control function. 3.
Chapter 6 Power and Power-Up Modes The computer's power resources include the AC adaptor, battery pack and any internal batteries. This chapter provides details on making the most effective use of these resources, and includes information on charging and changing batteries, tips for saving battery power, and information on the different power-up modes.
Power and Power-Up Modes Table 6-1 Power conditions continued Power on AC adaptor not connected Battery charge is above low battery trigger point • Operates • LED: Battery off DC IN off Battery charge is below low battery trigger point • Operates • LED: Battery flashes orange DC IN off Battery charge is exhausted Computer shuts down No battery installed • No operation Power off (no operation) • LED: Battery off DC IN off Monitoring of power condition As shown in the below table, the Battery, DC
Power and Power-Up Modes DC IN indicator Check the DC IN indicator to determine the power status with the AC adaptor connected - the following indicator conditions should be noted: Green Indicates the AC adaptor is connected and is correctly supplying power to the computer. Flashing orange Indicates a problem with the power supply. You should initially try plugging the AC adaptor into another power outlet - if it still does not operate properly, you should contact your reseller or dealer.
Power and Power-Up Modes Extended Capacity Battery Pack (option) The Extended Capacity Battery Pack can be purchased separately as an optional accessory. High Capacity Battery Pack (option) The High Capacity Battery Pack can be purchased separately as an optional accessory. Real Time Clock (RTC) battery The Real Time Clock (RTC) battery provides power for the internal real time clock and calendar function and also maintains the system configuration while the computer is turned off.
Power and Power-Up Modes ■ The battery pack, Extended Battery Pack and High Capacity Battery Pack are lithium ion batteries, which can explode if not replaced, used, handled or disposed of properly. Dispose of the battery as required by local ordinances or regulations. Use only batteries recommended by TOSHIBA as replacements. ■ The computer's RTC battery is a Ni-MH battery and should be replaced only by your dealer or by a TOSHIBA service representative.
Power and Power-Up Modes Battery charging notice The battery may not begin charging immediately under the following conditions: ■ The battery is extremely hot or cold (if the battery is extremely hot, it might not charge at all). To ensure the battery charges to its full capacity, you should charge it at room temperature of between 5° to 35°C (41° to 95°F). ■ The battery is nearly completely discharged.
Power and Power-Up Modes Maximizing battery operating time A battery's usefulness depends on how long it can supply power on a single charge, while how long the charge lasts in a battery depends on: ■ Processor speed ■ Screen brightness ■ Cooling method ■ System Sleep Mode ■ System Hibernation Mode ■ Display power off period ■ Hard disk drive power off period ■ How often and for how long you use the hard disk drive and external disk(c) drives, for example, optical disc and floppy diskette drive.
Power and Power-Up Modes 4. Connect the AC adaptor to the DC IN 15V jack of the computer, and to a wall outlet that is supplying power. The DC IN indicator should glow green, and the Battery indicator should glow orange to indicate that the battery pack is being charged, however, in the event that DC IN indicator does not glow this indicates that power is not being supplied - check the connections for the AC adaptor and the power cord. 5. Charge the battery pack until the Battery indicator glows green.
Power and Power-Up Modes 6. Slide and hold the battery release latch (2) and then remove the battery pack from the computer (3). Battery pack Battery release latch Battery lock Figure 6-1 Releasing the battery pack Installing the battery pack To install a battery pack, follow the steps as detailed below: Do not touch the battery release latch while holding the computer or the battery pack might fall out due to the unintentional release of the battery release latch and cause injuries. 1.
Power and Power-Up Modes TOSHIBA Password Utility The TOSHIBA Password Utility provides two levels of password security: User and Supervisor. Passwords set by the TOSHIBA Password Utility function are different from the Windows password. User Password To start the utility, point to or click the following items: Start -> All Programs -> TOSHIBA -> Utilities ->Password Utility The User Password dialog box contains two main fields: User Password and User Token.
Power and Power-Up Modes ■ Owner String (text box) You can use this box to associate text with the password. After you enter text, click Apply or OK. When the computer is started, this text will be displayed together with the prompt asking you to enter a password. ■ If you forget your HDD User Password, TOSHIBA will NOT be able to assist you, and your HDD will be rendered COMPLETELY and PERMANENTLY INOPERABLE.
Power and Power-Up Modes Supervisor Password If you set a Supervisor Password, some functions might be restricted when a user logs on with the User Password. To set a Supervisor Password, execute the file TOSPU.EXE. The file is located at: C:\Program Files\Toshiba\PasswordUtility\TOSPU.exe This utility lets you do the following: ■ Register, delete or change the Supervisor Password. ■ Create or invalidate a Supervisor Password token.
Power and Power-Up Modes Power-up modes The computer has three different power-up modes as follows: ■ Boot Mode : The computer will shut down without saving data - in view of this you must always save your work before you turn the computer off. ■ Hibernation Mode : Data in memory will be saved to the hard disk drive. ■ Sleep Mode : Data will maintained in the computer's memory. Please refer to the sections Turning on the power and Turning off the power in Chapter 1, Getting Started for further information.
Chapter 7 HW Setup & BIOS Setup This chapter explains how to use the TOSHIBA HW Setup program to configure your computer, and provides information on settings for various functions. Accessing HW Setup To run the HW Setup program, click Start -> All Programs -> TOSHIBA -> Utilities -> HWSetup. HW Setup window The HW Setup window contains a number of tabs (General, Display, Boot Priority, Keyboard, CPU, LAN, Device Config and USB) to allow specific functions of the computer to be configured.
HW Setup & BIOS Setup General This window displays the BIOS version and contains two buttons : Default and About. Default Return all HW Setup values to the factory settings. About Display the HW Setup version. Setup This field displays the installed BIOS version and date. Display This tab lets you customize your computer’s display settings for either the internal display or an external monitor. Power On Display This tab allows you to select the display to be used when the computer is started.
HW Setup & BIOS Setup Boot Priority Boot Priority Options This tab allows you to select the priority for booting the computer - the following settings are available: FDD −> HDD −> CDROM −> LAN The computer looks for bootable files on devices in the following order: 1. floppy diskette drive*1, 2. hard disk drive, 3. CD-ROM*2, 4. LAN. HDD −> FDD −> CDROM −> LAN The computer looks for bootable files on devices in the following order: 1. hard disk drive, 2. floppy diskette drive*1, 3. CD-ROM*2, 4. LAN.
HW Setup & BIOS Setup To change the boot drive, follow the steps below. 1. Hold down F12 and boot the computer. 2. The following menu will be displayed with the following icons: Built-in hard disk drive, CD-ROM, FDD (or SD memory card), Network (LAN), USB Memory boot. Please note that a highlighted bar will only appear under the selected device. 3. Use the left/right cursor keys to highlight the boot device you want and press ENTER.
HW Setup & BIOS Setup HDD Sets the USB memory to be the equivalent of a hard disk drive (default). With this setting, the USB memory device can be used to start the computer as though it were a hard disk drive based on the hard disk drive settings within both the Boot Priority and HDD Priority options detailed previously. FDD Sets the USB memory to be the equivalent of a floppy diskette drive.
HW Setup & BIOS Setup Always High The processor's power consumption and automatic clock speed switching functions are disabled - in use the processor will always run at its highest level of power consumption and its highest speed. Always Low The processor's power consumption and automatic clock speed switching functions are disabled - in use the processor will always run at a lower level of power consumption and a low speed.
HW Setup & BIOS Setup All Devices The computer's BIOS will setup and configure all devices. Setup by OS The operating system will setup and configure all of the devices that it can control (default). USB USB KB/Mouse Legacy Emulation You can use this option to enable or disable USB keyboard/mouse legacy emulation so that, even if your operating system does not support USB devices, you can still use a standard USB mouse and keyboard - to achieve this you should set the appropriate option(s) to Enabled.
HW Setup & BIOS Setup BIOS Setup Program Settings for some features are carried out in the BIOS setup program. Notes Before Using the BIOS Setup Application ■ In most cases, changes to the system's configuration should be made within Windows by using applications such as TOSHIBA HW Setup, TOSHIBA Password Utility, Windows Device Manager and so forth.
HW Setup & BIOS Setup Ending the BIOS Setup Program Halfway The configuration settings can be terminated halfway without saving any of the changes made by following the steps detailed below: 1. Press the ESC key - the Exit without saving? (Y/N) prompt to be displayed at the bottom of the screen. 2. Press the Y key - the BIOS setup application will exit and the computer will automatically restart.
HW Setup & BIOS Setup The Disabled command does not allow use of the Intel Virtualization Technology. The Enabled command allows use of the Intel Virtualization Technology. Enabled Enables Virtualization Technology. Disabled Disables Virtualization Technology (Default). Enhanced C-States This feature enables or disables the Enhanced C-States. Please note that this option is displayed only on models with an Intel® Core™ 2 Duo processor. Enabled This lowers the power consumption (Default).
HW Setup & BIOS Setup (To access it, Power Options -> Change plan settings -> Change advanced power settings -> Battery) The operation of this function is dependent upon battery status. The Critical Battery Wake-up only operates with Windows Vista™. Enabled When the remaining battery power is about to run out while the system is in Sleep Mode, the system is automatically woken up and then switched to Hibernation Mode (Default).
HW Setup & BIOS Setup The procedure to follow is as detailed below: 1. Move the cursor to the Clear TPM Owner setting and press either the Space key or BACK SPACE key. 2. A message is displayed at which you should press the Y, E, S, and ENTER keys in sequence - the Trusted Platform Module information will then be erased. 3. The Trusted Platform Module setting will then change from being Enable to Disabled and the setting no longer displayed.
Chapter 8 Troubleshooting TOSHIBA have designed this computer for durability, however, should problems occur you are able to use the procedures detailed in this chapter to help determine the cause. All users should become familiar with this chapter as knowing what might go wrong can help prevent problems from occurring in the first place.
Troubleshooting Preliminary checklist You should always consider the simplest solution first - the items detailed in this checklist are easy to fix and yet can cause what appears to be a serious problem: ■ Make sure you turn on all peripheral devices before you turn on the computer - this includes your printer and any other external device you are using.
Troubleshooting ■ Do you hear any beeps, if so how many, are they long or short and are they high pitched or low pitched? In addition, is the computer making any unusual noises? Write down what you hear. Record your observations so you can describe them in detail to your reseller, dealer or service provider. Software Hardware The problems may be caused by your software or disk.
Troubleshooting System start-up When the computer does not start properly, check the following items: ■ Self Test ■ Power Sources ■ Power-on Password Self test When the computer starts up, the self test will be run automatically, and the following will be displayed: S In Touch with Tomorrow TOSHIBA This message remains on the screen for a few seconds.
Troubleshooting Problem Procedure Computer shuts down and DC IN indicator blinks orange Leave the computer off until the DC IN indicator stops blinking. It is recommended to leave the computer off until the interior reaches room temperature even though the DC IN indicator stops blinking. If the computer has reached room temperature and it still does not start, or if it starts but shuts down quickly, contact your reseller, dealer or service provider.
Troubleshooting Problem Procedure Battery doesn’t charge when the AC adaptor is attached (Battery indicator does not glow orange). If the battery is completely discharged, it will not begin charging immediately, in these instances you should wait a few minutes before trying again. If the battery still does not charge, you should check that the power outlet the AC adaptor is connected to is supplying power - this can be tested by plugging another appliance into it.
Troubleshooting Real Time Clock Problem Procedure The following message is Displayed on the screen: RTC battery is low or CMOS checksum is inconsistent. Press [F1] key to set Date/Time. The charge in the Real Time Clock (RTC) battery has run out - you will need to set the date and time in the BIOS setup application by using the following steps: 1. Press the F1 key - the BIOS setup application will load. 2. Set the date in the System Date field. 3. Set the time in the System Time field. 4.
Troubleshooting Internal display panel Apparent computer's display panel problems may be related to the computer's setup and configuration - please refer to Chapter 7, HW Setup & BIOS Setup, for further information. Problem Procedure No display Press the FN + F5 hot keys to adjust the display priority, and to make sure it is not set for output to an external monitor. Markings appear on the These marks may have come from contact with computer's display the keyboard and Touch Pad while the display panel.
Troubleshooting Problem Procedure Slow performance The files on the hard disk drive may be fragmented - in this instance you should run the disk Defragmentation utility to check the condition of your files and the hard disk drive. Please refer to the operating system's documentation or online Help File for further information on running and using the Defragmentation utility. As a last resort you should reformat the hard disk drive and then reload the operating system and all other files and data.
Troubleshooting DVD-ROM&CD-R/RW drive For more information, refer to Chapter 4, Operating Basics. Problem Procedure You cannot access a CD/DVD in the drive Make sure the drive’s disc tray is securely closed. Press gently until it clicks into place. Open the disc tray and make sure the CD/DVD is properly seated. It should lie flat with the label facing up. A foreign object in the disc tray could block laser light from reading the CD/DVD. Make sure there is no obstruction. Remove any foreign object.
Troubleshooting Problem Procedure Cannot write correctly If you have trouble writing, make sure you are observing the following precautions: ■ Use only media recommended by TOSHIBA. ■ Do not use the mouse or keyboard during writing. ■ Use only the software supplied with the computer for recording. ■ Do not run or start other software during writing. ■ Do not jar the computer during writing. ■ Do not connect/disconnect external devices or install/remove internal cards during writing.
Troubleshooting Check the type of CD/DVD you are using. The drive supports: DVD-ROM: DVD-ROM, DVD-Video CD-ROM: CD-DA, CD-Text, Photo CDTM (single/multi-session), CD-ROM Mode 1, Mode 2, CD-ROM XA Mode 2 (Form1, Form2), Enhanced CD (CD-EXTRA), Addressing Method 2 Recordable DVD: DVD-R/-R DL, DVD+R/+R DL, DVD-RW, DVD+RW, DVD-RAM Check the region code on the DVD. It must match that on the DVD Super Multi drive. Region codes are listed in the Optical disc drives section in Chapter 2, The Grand Tour.
Troubleshooting PC Card For further information, please refer to Chapter 3, Hardware, Utilities and Options. Problem Procedure PC Card error occurs Remove the PC Card from the computer and then reinsert it in order to ensure it is firmly connected. In the event that the PC Card is attached to an external peripheral device, ensure that this connection is properly made. If the problem persists, then you should refer to the documentation supplied with your PC Card for further information.
Troubleshooting Memory Stick/Memory Stick PRO/Memory Stick PRO Duo Refer also to Chapter 3, Hardware, Utilities and Options. Problem Procedure Memory Stick/Memory Stick PRO/Memory Stick PRO Duo error occurs Reseat the Memory Stick/Memory Stick PRO/Memory Stick PRO Duo to make sure it is firmly connected. Check the card’s documentation. You cannot write to a Memory Stick/Memory Stick PRO/Memory Stick PRO Duo Make sure the Memory Stick/Memory Stick PRO/Memory Stick PRO Duo is not write protected.
Troubleshooting Dual Pointing device If you are using a USB mouse, you should also refer to both the USB device section in this chapter, and the documentation supplied with your mouse. Touch Pad/AccuPoint Problem Procedure Either the Touch Pad or the AccuPoint does not work. Check the Device Select settings. Click Start -> Control Panel -> Hardware and Sound -> Mouse icon. Pressing FN + F9 to enable.
Troubleshooting Problem Procedure The reaction of Touch pad is either too sensitive or not sensitive enough. Adjust the touch Sensitivity. 1. Click Start -> Control Panel -> Hardware and Sound -> Mouse icon. 2. Within the Mouse Properties window, click the Advanced tab. 3. Click the Advanced feature settings button. 4. Advanced feature settings is displayed. 5. Move the slide of adjust the pointer speed in relation to the standard Windows setting. Click the OK button. 6.
Troubleshooting Problem Procedure The mouse pointer moves erratically The elements of the mouse responsible for detecting movement might be dirty - please refer to the documentation supplied with the mouse for instructions on how to clean it. If you are still unable to resolve the problem, contact your reseller, dealer or service provider. Fingerprint Sensor User’s Manual Problem Procedure Reading of the fingerprint was not successful.
Troubleshooting USB device In addition to the information in this section, please also refer to the documentation supplied with your USB device. Problem Procedure USB device does not work Remove the USB device from the computer and then reconnect it to a free port it in order to ensure it is firmly attached. Ensure that any required USB device drivers are properly installed - to achieve this you should refer to both the device documentation and the operating system documentation.
Troubleshooting Problem Procedure An error will occur if a memory module is inserted into Slot B when no memory module is inserted in Slot A. Remove the memory module from Slot B and insert it into Slot A. Sound system In addition to the information in this section, please also refer to the documentation supplied with your audio device. Problem Procedure No sound is heard Adjust the volume control dial. Check the software volume settings.
Troubleshooting External monitor Please also refer to Chapter 3, Hardware, Utilities and Options, and to the documentation supplied with your monitor for further information. Problem Procedure Monitor does not turn on After confirming that the monitor's power switch is on, you should check the connections to make sure that the power cord/adaptor is firmly connected to the monitor and to a working power outlet. No display Try adjusting the contrast and brightness controls on the external monitor.
Troubleshooting i.LINK (IEEE1394) device Problem Procedure i.LINK device does not function Make sure the cable is securely connected to the computer and to the device. Make sure the device’s power is turned on. Reinstall the drivers. Open the Windows Control Panel and double-click the Add Hardware icon. Follow the on-screen directions. Restart Windows. If problems persist, contact your dealer. Modem Refer to Appendix C, AT Commands and Appendix D, S-registers.
Troubleshooting Problem Procedure Character display becomes garbled during a communication session In data transmission, make sure the parity bit and stop bit settings correspond with those of the remote computer. Check the flow control and communication protocol. You cannot receive an incoming call Check the rings before auto answer setting in your communications application. You can also use the ATS0 command. Refer to Appendix D, S-registers. If problems persist, contact your dealer.
Troubleshooting Check to ensure the Bluetooth Manager application is running on the computer and that power to the external Bluetooth device is turned on. Check to ensure that no optional Bluetooth Adaptor is installed in the computer - the built-in Bluetooth hardware cannot operate simultaneously with another Bluetooth controller. If you are still unable to resolve the problem, contact your reseller, dealer or service provider.
Troubleshooting ■ If your hard disk drive or other storage media contains sensitive data, you should be aware that standard deletion procedures do not remove data from the media. These standard deletion procedures include: ■ Selecting Delete for a target file ■ Putting files in the Recycle Bin and emptying the Recycle Bin ■ Reformatting the media ■ Reinstalling an operating system from the recovery CD-ROM The procedures above delete only the initial part of the data used for file management.
Troubleshooting Where to write If you are still unable to solve the problem and suspect that it is hardware related, write to TOSHIBA at the nearest location listed below: Outside of Europe In Europe Australia TOSHIBA Australia Pty. Ltd. Information Systems Division 84-92 Talavera Road North Ryde N.S.W. 2113 Sydney Germany & Austria TOSHIBA Europe (I.E.) GmbH Geschäftsbereich, Deutschland-Österreich Hammfelddamm 8, D-41460 Neuss, Germany Canada TOSHIBA of Canada Ltd.
Appendix A Specifications This appendix summarizes the computer’s technical specifications. Physical Dimensions Refer to User Information Guide about Weight and Size.
Specifications Power Requirements AC adaptor 100-240 volts AC 50 or 60 hertz (cycles per second) Computer 15 V DC 5.
Specifications User’s Manual Communication speed Data transmission and reception 300/1200/2400/4800/7200/9600/12000/14400/16 800/19200/21600/24000/26400/28800/31200/33 600 bps Data reception only with V.
Appendix B Display Controller and Video mode Display controller The display controller interprets software commands into hardware commands that turn particular parts on the screen on or off. Due to the display panel's increased resolution, lines may appear broken in when displaying images in full-screen text mode. The display controller also controls the video mode and uses industry standard rules to govern the screen resolution and the maximum number of colors that can be displayed at any one time.
Appendix C AT Commands In most cases, you will not need to type AT commands manually. However, there might be some occasions when you will need to do so. This chapter describes AT commands for data mode. Fax and voice commands are taken care of by application software. The format for entering AT commands is: ATXn where X is the AT command, and n is the specific value for that command. After you type in the command press ENTER.
AT Commands A Answer command This command instructs the modem to go off-hook and answer an incoming call. Bn Communication standard setting This command determines the communication standard CCITT or Bell. B0 Selects CCITT V.22 mode when the modem is at 1200 bps. B1 Selects Bell 212A when the modem is at 1200 bps (default). B15 Selects V.21 when the modem is at 300 bps. B16 Selects Bell 103J when the modem is at 300 bps (default).
AT Commands E0 Disables echo to the computer. E1 Enables echo to the computer (default). Result Codes: OK n=0,1 ERROR Otherwise Hn Hook control This command instructs the modem to go on-hook to disconnect a call, or off-hook to make the phone line busy. H0 Modem goes on-hook (default). H1 Modem goes off-hook. Result Codes: OK n=0,1 ERROR Otherwise In Request ID information This command displays product information about the modem. I0 Returns modem identity string and driver version number.
AT Commands Result Codes: OK n=0,1,2,3 ERROR Otherwise Nn Modulation handshake This command controls whether or not the local modem performs a negotiated handshake at connection time with the remote modem when the communication speed of the two modems is different. N0 When originating or answering, this is for handshake only at the communication standard specified by S37 and the ATB command.
AT Commands Result Codes: OK n=0,1 ERROR Otherwise T Select tone dialing This command instructs the modem to send DTMF tones while dialing. Dialed digits are tone dialed until a P command or dial modifier is received. This is the default setting. Vn DCE response format This command controls whether result codes (including call progress and negotiation progress messages) are displayed as words or their numeric equivalents. V0 Displays result codes as digits. V1 Displays result codes as text (default).
AT Commands Dial tone detect Disabled:The modem dials a call regardless of whether it detects a dial tone. Enabled:The modem dials only upon detection of a dial tone, and disconnects the call if the dial tone is not detected within 10 seconds. Busy tone detect Disabled:The modem ignores any busy tones it receives. Enabled:The modem monitors for busy tones.
AT Commands &D2 If the DTR signal is not detected while in on-line data mode, the modem disconnects (default). &D3 Reset on the on-to-off DTR transition. Result Codes: OK n=0,1,2,3 ERROR Otherwise &F Load factory settings This command loads the configuration stored and programmed at the factory. This operation replaces all of the command options and the Sregister settings in the active configuration with factory values. &F Recall factory setting as active configuration. &Gn V.
AT Commands &Tn Self-test commands These tests can help to isolate problems if you experience periodic data loss or random errors. &T0 Abort. Stops any test in progress. &T1 Local analog loop. This test verifies modem operation, as well as the connection between the modem and computer. Any data entered at the local DTE is modulated, then demodulated, and returned to the local DTE. To work properly, the modem must be off-line.
AT Commands \N3 V.42, MNP, or buffered (default). The modem attempts to connect in V.42 error control mode. If this fails, it attempts to connect in MNP mode. If this fails, it connects in buffer mode and continues operation. This is also known as V.42/MNP auto reliable mode (same as &Q5). \N4 V.42 or disconnect. The modem attempts to connect in V.42 error control mode. If this fails, the modem disconnects. \N5 V.42. MNP or buffered (same as \N3). \N7 V.42. MNP or buffered (same as \N3).
Appendix D S-registers S-registers contain the settings that determine how a number of functions of the internal modem operate. For example, how many times to let the telephone ring before the modem answers and how long to wait before it hangs up if a connection fails. You can also customize certain AT commands such as the escape sequence and command line termination. The contents of the registers are changed automatically when you modify corresponding settings in your communication software.
S-registers Range:0-255 Default:0 Units:rings S1 Ring counter This register is read only. The value of S1 is incremented with each ring. If no ring occurs over a six-second interval, this register is cleared. Range:0-225 Default:0 Units:rings S2 AT escape character (user defined) This register determines the ASCII values used for an escape sequence. The default is the + character. The escape sequence allows the modem to exit data mode and enter command mode when on-line.
S-registers S5 Command line editing character (user defined) This register sets the character recognized as a backspace and pertains to asynchronous only. The modem will not recognize the backspace character if it is set to a value that is greater than 32 ASCII. This character can be used to edit a command line. When the echo command is enabled, the modem echoes back to the local DTE the backspace character, an ASCII space character, and a second backspace character.
S-registers S8 Comma pause time This register sets the time, in seconds, that the modem must pause when it encounters a comma (,) in the dial command string. In some countries/regions, S8 will set both wait before dialing and comma pause time. Range:0-255 Default:2 Units:seconds S11 DTMF dialing speed This register determines the dialing speed which is prefixed for each country/region. Range:50-255 Default:95 Units:.
S-registers S37 = 10 12000 bps S37 = 11 14400 bps S37 = 12 16800 bps S37 = 13 19200 bps S37 = 14 21600 bps S37 = 15 24000 bps S37 = 16 26400 bps S37 = 17 28800 bps S37 = 18 31200 bps S37 = 19 33600 bps AT command set result codes The following table shows the result codes.
S-registers CONNECT 4800 EC*1 11 Connection at 4800 bps CONNECT 9600 EC*1 12 Connection at 9600 bps CONNECT 14400 EC*1 13 Connection at 14400 bps CONNECT 19200 EC*1 14 Connection at 19200 bps CONNECT 7200 EC*1 24 Connection at 7200 bps CONNECT 12000 EC*1 25 Connection at 12000 bps CONNECT 16800 EC*1 86 Connection at 16800 bps CONNECT 300 EC*1 40 Connection at 300 bps CONNECT 21600 EC*1 55 Connection at 21600 bps CONNECT 24000 EC*1 56 Connection at 24000 bps CONNECT 26400 EC*1
Appendix E V.90 The TOSHIBA internal modem uses V.90 technology. The modem is capable of downstream speeds of 56kbps (kilobits per second) when connected to an Internet service provider that supports V.90. As with any modem, the actual throughput (speed of data transfer) depends on analog telephone line conditions, which can vary considerably. Therefore, many users will experience throughput in the range of 28-50kbps under normal telephone line conditions. Upstream data flows at the V.34 rate. V.
V.90 Table E-1 Result codes for a V.90 connection User’s Manual No.
V.90 * EC stands for the Error Control method, which appears only when the extended result codes configuration option is enabled. EC is replaced by one of the following symbols, depending on the error control method used. V42bis V.42 error control and V.42bis data compression V42 V.42 error control only NoEC No error control protocol AT Command User’s Manual -V90=* V.90 Dial Line Rate -V90 sets the maximum V.90 downstream that the modem attempts to connect. -V90=0 V.90 disabled -V90=1 V.
Appendix F Wireless LAN This appendix is intended to help you get your Wireless LAN network up and running, with a minimum of parameters. Card Specifications Form Factor PCI Express Mini Card Compatibility ■ IEEE 802.11 Standard for Wireless LANS ■ Wi-Fi (Wireless Fidelity) certified by the Wi-Fi Alliance. The ‘Wi-Fi CERTIFIED’ logo is a certification mark of the Wi-Fi Alliance.
Wireless LAN Radio Characteristics Radio Characteristics of Wireless LAN Cards may vary according to: ■ Country/region where the product was purchased ■ Type of product Wireless communication is often subject to local radio regulations. Although Wireless LAN wireless networking products have been designed for operation in the license-free 2.4GHz and 5GHz band, local radio regulations may impose a number of limitations to the use of wireless communication equipment.
Wireless LAN 5 2432 6 2437 7 2442 8 2447 9 2452 10 2457*1 11 2462 12 2467*2 13 2472*2 *1 Factory-set default channels *2 Refer to the sheet Approved Countries/Regions for use for the countries/regions that in which these channels can be used.
Wireless LAN User’s Manual 52 5260 56 5280 60 5300 64 5320 100 5500 104 5520 108 5540 112 5560 116 5580 120 5600 124 5620 128 5640 132 5660 136 5680 140 5700 149 5745 153 5765 157 5785 161 5805 165 5825 F-4
Appendix G Intel® Matrix Storage Manager If you are installing the operating system on a computer system which is configured for AHCI mode, you must pre-install the Intel® Matrix Storage Manager driver using the F6 installation method described in the Manually Setting up Windows (Windows Vista™) or Manually Setting up Windows Manually (Windows XP) sections. This model does not support RAID functionality.
Intel® Matrix Storage Manager Windows Setup Procedure 1. Connect the USB floppy diskette drive and insert the above disk. 2. Insert the Windows Setup DVD into the optical disc drive and boot the computer from the DVD. The Windows Setup program will start. 3. Carry out the setup process by following the instructions displayed on the setup screen. When the message "Which type of installation do you want?" appears, select Custom (advanced). 4.
Intel® Matrix Storage Manager 3. When the message "Press F6 if you need to install a third party SCSI or RAID driver" appears on the screen, press the F6 key. 4. When the message "Setup will load support for the following mass storage device(s):" appears on the screen, press the S key. 5. Select "Intel(R) 82801HEM/HBM SATA AHCI Controller (Mobile ICH8M-E/M)" and press the Enter key. 6. Follow the onscreen instructions to continue setting up windows.
Appendix H Bluetooth wireless technology Interoperability Bluetooth® Adaptors from TOSHIBA are designed to be interoperable with any product with Bluetooth wireless technology that is based on Frequency Hopping Spread Spectrum (FHSS) radio technology, and is compliant to: ■ Bluetooth Specification Ver.2.0+EDR, as defined and approved by The Bluetooth Special Interest Group. ■ Logo certification with Bluetooth wireless technology as defined by The Bluetooth Special interest Group.
Bluetooth wireless technology Interoperability ■ Bluetooth wireless technology is a new innovative technology, and TOSHIBA has not confirmed compatibility of its Bluetooth® products with all computers and/or equipment using Bluetooth wireless technology other than TOSHIBA portable computers. Always use Bluetooth® Adaptors from TOSHIBA in order to enable wireless networks over two or more (up to a total of seven) TOSHIBA portable computers using these cards.
Bluetooth wireless technology Interoperability Bluetooth wireless technology and your Health The products with Bluetooth wireless technology, like other radio devices, emit radio frequency electromagnetic energy. The level of energy emitted by devices with Bluetooth wireless technology however is far much less than the electromagnetic energy emitted by wireless devices like for example mobile phones.
Bluetooth wireless technology Interoperability L ‘ utilisation de ce dispositif est autorisée seulement aux conditions suivantes: (1) il ne doit pas produire de brouillage et (2) l’ utilisateur du dispositif doit étre prét à accepter tout brouillage radioélectrique reçu, même si ce brouillage est susceptible de compromettre le fonctionnement du dispositif. The term “IC” before the equipment certification number only signifies that the Industry Canada technical specifications were met.
Bluetooth wireless technology Interoperability Caution: Exposure to Radio Frequency Radiation The radiated output power of the Bluetooth® Adaptor from TOSHIBA is far below the FCC radio frequency exposure limits. Nevertheless, the Bluetooth® Adaptor from TOSHIBA shall be used in such a manner that the potential for human contact during normal operation is minimized.
Bluetooth wireless technology Interoperability Using Bluetooth® Adaptor from TOSHIBA equipment in Japan In Japan, the frequency bandwidth of 2,400 - 2,483.5 MHz for second generation low-power data communication systems such as this equipment overlaps that of mobile object identification systems (premises radio station and specified low-power radio station). 1. Sticker Please put the following sticker on computer incorporating this product.
Bluetooth wireless technology Interoperability Device Authorization This device obtains the Technical Conditions Compliance Approval, and it belongs to the device class of radio equipment of low-power data communication system radio station stipulated in the Telecommunications Business Law. The Name of the radio equipment: EYXF3CS JAPAN APPROVALS INSTITUTE FOR TELECOMMUNICATIONS EQUIPMENT Approval Number: D05-0074001 The following restrictions apply: Do not disassemble or modify the device.
Appendix I AC Power Cord and Connectors The power cord’s AC input plug must be compatible with the various international AC power outlets and the cord must meet the standards for the country/region in which it is used. All cords must meet the following specifications: Length: Minimum 1.7 meters Wire size: Minimum 0.75 mm2 Current rating: Minimum 2.5 amperes Voltage rating: 125 or 250 VAC (depending on country/region’s power standards) Certification agencies U.S.
AC Power Cord and Connectors Finland: FIMKO Sweden: SEMKO France: LCIE Switzerland: SEV Germany: VDE United Kingdom: BSI In Europe, two conductors power cord must be VDE type, H05VVH2-F or H03VVH2-F and for three conductors power cord must be VDE type, H05VV-F. For the United States and Canada, two pin plug configuration must be a 215P (250V) or 1-15P (125V) and three pin plug configuration must be 615P (250V) or 5-15P (125V) as designated in the U.S.
Appendix J TOSHIBA Anti-theft Protection Timer This feature allows you to set up a timer-activated BIOS password that will prevent unauthorised system access in the event of theft. When the time limit is exceeded, you are required to provide the Password or fingerprint authentication for the BIOS and Hard Disk Drive to gain access to the system. To set permissions and limits for the TOSHIBA Anti-theft Protection Timer please use the TOSHIBA Password Utility.
Appendix K Legal Footnotes This chapter states the Legal Footnotes information applicable to TOSHIBA computers. In the text in this manual, *XX is used to show which Legal Footnotes description is related to TOSHIBA computers. Description(s) related to this computer are marked with a blue *XX in this manual. Clicking on *XX will display the related description. Non-applicable Icons*1 Certain computer chassis are designed to accommodate all possible configurations for an entire product series.
Legal Footnotes ■ use of computer at temperatures outside the range of 5°C to 30°C (41°F to 86°F) or >25°C (77°F) at high altitude (all temperature references are approximate and may vary depending on the specific computer model please refer to your computer documentation or visit the Toshiba website at www.pcsupport.toshiba.com for details). CPU performance may also vary from specifications due to design configuration. Under some conditions, your computer product may automatically shutdown.
Legal Footnotes Battery Life*4 Battery life may vary considerably depending on product model, configuration, applications, power management settings and features utilized, as well as the natural performance variations produced by the design of individual components. Published battery life numbers are achieved on select models and configurations tested by Toshiba at the time of publication. Recharge time varies depending on usage. Battery may not charge while computer is consuming full power.
Legal Footnotes Wireless LAN*8 The transmission speed over the wireless LAN and the distance over which wireless LAN can reach may vary depending on surrounding electromagnetic environment, obstacles, access point design and configuration, and client design and software/hardware configurations. The actual transmission speed will be lower than the theoretical maximum speed. The Intel® Next-Gen Wireless-N adaptor is based on a draft release version of the IEEE 802.
Glossary The terms in this glossary cover topics related to this manual. Alternate naming is included for reference.
Glossary I/O: input/output IRQ: interrupt request KB: kilobyte LCD: liquid crystal display LED: light emitting diode LSI: large scale integration MB: megabyte MS-DOS: Microsoft Disk Operating System OCR: optical character recognition (reader) PCB: printed circuit board PCI: peripheral component interconnect RAM: random access memory RGB: red, green, and blue ROM: read only memory RTC: real time clock SCSI: small computer system interface SIO: serial input/output TFT: thin-film transistor UART: universal as
Glossary analog signal: A signal whose characteristics such as amplitude and frequency vary in proportion to (are an analog of) the value to be transmitted. Voice communications are analog signals. ANSI: American National Standards Institute. An organization established to adopt and define standards for a variety of technical disciplines. For example, ANSI defined the ASCII standard and other information processing requirements. antistatic: A material used to prevent the buildup of static electricity.
Glossary bus: An interface for transmission of signals, data or electric power. byte: The representation of a single character. A sequence of eight bits treated as a single unit; also the smallest addressable unit within the system. C cache memory: High speed memory which stores data that increases processor speed and data transfer rate. When the CPU reads data from main memory, it stores a copy of this data in cache memory.
Glossary compatibility: 1) The ability of one computer to accept and process data in the same manner as another computer without modifying the data or the media upon which it is being transferred. 2) the ability of one device to connect to or communicate with another system or component. components: Elements or parts (of a system) which make up the whole (system). computer program: A set of instructions written for a computer that enable it to achieve a desired result.
Glossary delete: To remove data from a disk or other data storage device. Synonymous with erase. device driver: A program that controls communication between a specific peripheral device and the computer. The CONFIG.SYS file contains device drivers that MS-DOS loads when you turn the computer on. dialog box: A window that accepts user input to make system settings or record other information. disk drive: The device that randomly accesses information on a disk and copies it to the computer’s memory.
Glossary E echo: To send back a reflection of the transmitted data to the sending device. You can display the information on the screen, or output it to the printer, or both. When a computer receives back data it transmitted to a CRT (or other peripheral device) and then retransmits the data to printer, the printer is said to echo the CRT. erase: See delete. escape: 1) A code (ASCII code 27), signaling the computer that what follows are commands; used with peripheral devices such as printers and modems.
Glossary graphics: Drawings, pictures, or other images, such as charts or graphs, to present information. H hard disk: A non-removable disk usually referred to as drive C. The factory installs this disk and only a trained engineer can remove it for servicing. Also called fixed disk. hard disk drive (HDD): An electromechanical device that reads and writes a hard disk. See also hard disk.
Glossary I/O devices: Equipment used to communicate with the computer and transfer data to and from it. J jumper: A small clip or wire that allows you to change the hardware characteristics by electrically connecting two points of a circuit. K K: Taken from the Greek word kilo, meaning 1000; often used as equivalent to 1024, or 2 raised to the 10th power. See also byte and kilobyte. KB: See kilobyte. keyboard: An input device containing switches that are activated by manually pressing marked keys.
Glossary microprocessor: A hardware component contained in a single integrated circuit that carries out instructions. Also called the central processing unit (CPU), one of the main parts of the computer. mode: A method of operation, for example, the Boot Mode, Sleep Mode or the Hibernation Mode. monitor: A device that uses rows and columns of pixels to display alphanumeric characters or graphic images. See also CRT.
Glossary P parity: 1) The symmetrical relationship between two parameter values (integers) both of which are either on or off; odd or even; 0 or 1. 2) In serial communications, an error detection bit that is added to a group of data bits making the sum of the bits even or odd. Parity can be set to none, odd, or even. password: A unique string of characters used to identify a specific user. The computer provides various levels of password protection such as user, supervisor and eject.
Glossary RGB: Red, green, and blue. A device that uses three input signals, each activating an electron gun for a primary additive color (red, green, and blue) or port for using such a device. See also CRT. RJ45: A modular LAN jack. ROM: Read Only Memory: A nonvolatile memory chip manufactured to contain information that controls the computer’s basic operation. You cannot access or change information stored in ROM.
Glossary TFT display: A liquid crystal display (LCD) made from an array of liquid crystal cells using active-matrix technology with thin film transistor (TFT) to drive each cell. Touch Pad: A pointing device integrated into the TOSHIBA computer palm rest. TTL: Transistor-transistor logic. A logic circuit design that uses switching transistors for gates and storage. U Universal Serial Bus: This serial interface lets you communicate with several devices connected in a chain to a single port on the computer.
Index A AC adaptor 3-2 additional 3-30 connecting 1-4 ASCII characters 5-7 B BIOS Setup 7-8 Battery charging 6-5 extending life 6-7 indicator 2-11, 6-2 monitoring capacity 6-6 real time clock 3-2, 6-4 save mode 3-6 types 6-3 Battery pack 2-8, 3-2 additional 6-1 replacing 6-8 Bluetooth 3-4, 4-30 Bluetooth Stack for Windows by Toshiba 3-11 problems 8-22 Boot Priority 7-3 Bridge media slot 2-4, 3-15 inserting 3-17 removing 3-18 C CD-ROM 2-4 CD-ROM drive 8-9 Cleaning the computer 4-34 Cooling vents 2-3 D
TECRA A9/ TECRA S5/ TECRA P5/ Satellite Pro S200 FN + ENTER 5-3 FN + ESC (Mute) 5-3 FN + F1 (Lock) 5-3 FN + F10 (Arrow mode) 5-3 FN + F11 (Numeric mode) 5-3 FN + F12 (ScrLock) 5-3 FN + F2 (Power Plan) 5-3 FN + F3 (Sleep) 5-4 FN + F4 (Hibernate) 5-4 FN + F5 (Output) 5-4 FN + F6 (Brightness Down) 5-4 FN + F7 (Brightness Up) 5-4 FN + F8 (Wireless) 5-4 FN + F9 (Touch Pad) 5-4 FN + space (Zoom) 5-4 Fingerprint Sensor location 2-8 problems 8-17 using 4-3 Floppy diskette care 4-22 Function keys 5-2 G Graphics c
TECRA A9/ TECRA S5/ TECRA P5/ Satellite Pro S200 Media care 4-22 CD/DVDs 4-22 Floppy diskettes 4-22 Memory 3-2 additional 3-30 installing 3-20 problems 8-18 removing 3-22 Memory Stick/Memory Stick PRO/Memory Stick PRO Duo 3-17 problems 8-14 Modem 3-4 connecting 4-27 disconnecting 4-28 jack 2-5 problems 8-21 properties menu 4-26 region selection 4-26 Moving the computer 4-34 MultiMediaCard problems 8-14 P PC Card 3-13 inserting 3-13 problems 8-13 removing 3-14 Password Starting the computer by 6-12 Superv
TECRA A9/ TECRA S5/ TECRA P5/ Satellite Pro S200 Serial port 3-28 Sleep Mode System automatic 3-6 setting 1-8 Soft keys ENTER 5-3 ScrLock 5-3 enhanced keyboard 5-2 Sound system Stereo speakers 2-9 headphone jack 2-2 microphone 2-2 microphone jack 2-2 problems 8-19 volume control dial 2-2 X xD picture card problems 8-14 T TOSHIBA Assist 3-11 TOSHIBA Assist button 3-5 TOSHIBA ConfigFree 3-11 TOSHIBA DVD-RAM Utility 3-12 TOSHIBA Disc Creator 3-11, 4-20 TOSHIBA Express Port Replicator 3-30 TOSHIBA HDD Prote
