3LCD DATA PROJECTOR TLP-T70M TLP-T71M TLP-T60M TLP-T61M TLP-S40 TLP-S41 Before Using OWNER’S MANUAL (XGA) (XGA / With Document Camera) (SVGA) TLP-T70M / T60M / TLP-S40 Others Maintenance (SVGA / With Document Camera) Operations (XGA / With Document Camera) Preparations (XGA)
Before Using The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to the presence of uninsulated "dangerous voltage" within the product's enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons. The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance.
5. Heat 8. Power-Cord Protection The product should be situated away from heat sources such as radiators, heat registers, stoves, or other products (including amplifiers) that produce heat. Power-supply cords should be routed so that they are not likely to be walked on or pinched by items placed upon or against them, paying particular attention to cords at plugs, convenience receptacles, and the point where they exit from the product. 11. Object and Liquid Entry 14.
IMPORTANT SAFETY INSTRUCTIONS (Continued) 18. Servicing Unplug this product from the wall outlet and refer servicing to qualified service personnel under the following conditions: a) When the power-supply cord or plug is damaged. b) If liquid has been spilled, or objects have fallen into the product. c) If the product has been exposed to rain or water. d) If the product does not operate normally by following the operating instructions.
POWER SUPPLY CORD SELECTION If your line voltage is 220 to 240V, use one of the following types of cable. MODEL NO. / RATING Label Plug configuration Plug type WARNING Label SERIAL NO. Label MANUFACTURED; Plug configuration Line voltage EURO 220 – 240V UK 220 – 240V SERIAL NO. CAUTION Label Use a 5A fuse which is approved by ASTA or BSI to BSI362. Always replace the fuse cover after changing the fuse.
EXEMPTION CLAUSES Avoid Volatile Liquid • Toshiba Corporation bears no responsibility in the case of damages arising from natural disaster such as earthquakes, lightning, etc., fire not liable to Toshiba Corporation, operating by third parties, other accidents, or use under abnormal conditions including erroneous or improper operation and other problems. • Toshiba Corporation bears no responsibility for incidental damages (lost profit, work interruption, corruption or loss of the memory contents, etc.
Before Using Mainenance SAFETY PRECAUTIONS ................................................................................ 2 IMPORTANT SAFETY INSTRUCTIONS ......................................................... 3 LABEL LOCATIONS ........................................................................................ 8 POWER SUPPLY CORD SELECTION ............................................................ 9 IMPORTANT PRECAUTIONS .........................................................................
Preparations Checking the package contents Names of each part on the main unit Please make sure that the following items are included in the box, along with the main unit. If any item is missing, please contact the store immediately where you purchased the product.
Names of each part on the control panel and remote control Control panel Remote Control CLASS 1 LED PRODUCT (15) (1) AUTO (12) (13) SET (8) (7) (4) MUTE (11) (5) FREEZE (10) (12) (11) ON (4) (2) (3) ON/ STANDBY (3) (7) (8) (9) (10) (1) Remote control transmitter CALL KEYSTONE FAN TEMP LAMP Names of each part on the document camera (models with a document camera) INPUT (2) (13) ON / STANDBY (1) ZOOM + (8) (6) CANCEL (9) (14) INPUT MENU VOL. - (2) (6) ZOOM + VOL.
Preparing and using the remote control Placement ■ Loading dry-cell batteries into the remote control ■ Operating the remote control Placement Styles q Remove the battery cover. Point the remote control toward the projector’s infrared remote sensor, and press a button on the remote control. As shown in the figures below, this device can be placed in 4 different styles. The factory setting is “floor-mounted front projection.” Set the placement style in the default setting menu p.
Placement (Continued) Connection Projection Distance and Screen Size (with optical zooming) Before connection Use the figures, tables, and formulas below to determine the screen size and projection distance. (Screen sizes are approximate values for full-size picture with no keystone adjustment) • Read the owner’s manual of the device to connect to the projector. • Some types of computer cannot be used or connected to this projector. Check for an RGB output terminal, supported signal p.46 , etc.
Operations Turning the power on and off Connecting the power cord Turning the power off 1 2 1 Insert the power cord plug into a wall or other power outlet. When the power cord is plugged in, the following three green indicators will come on for several seconds: ON, TEMP, and LAMP. Next, the ON indicator will change to orange, indicating standby mode. (Do not perform any operations while the 3 green indicators are on.) (Supplied) Power cord connector Press the ON/STANDBY button.
Basic operations 5 Projector placement angle adjustments Turn on the power by following the instructions in “Turning on the power” p.22 . 2 Select the language and the lamp power (When using the first time). When the projector is used for the first time after purchase, menu for language and lamp power selection and configuration is displayed in English. (If the screen is out of focus, adjust it according to the step 6 .) q Use the or buttons to select the desired language and press the button.
Using handy features ■ Using auto setting (Auto setting) ■ Correcting the keystone distortion (Keystone) This function sets up the projector to the optimum state for each type of the input signal by using simple operations. Control panel FAN TEMP LAMP 1 Press the AUTO SET button. Remote Control ON ON/ STANDBY CALL INPUT ON / STANDBY KEYSTONE AUTO SET When the foot adjuster p.25 is used to change the projection angle, the picture will undergo keystone (trap- Control panel ezoidal) distortion.
Using handy features (Continued) 2 Press the ZOOM + button to bring it back to the original size. ■ Enlarging the picture size (Resize) Each time the ZOOM + button is pressed, the image size increases. (You cannot make it larger than the original size.) The image being projected can be enlarged. 1 Press the remote control’s RESIZE button. The enlargement ratio is increased each time the RESIZE button is pressed.
Using handy features (Continued) Using the menus ■ Displaying Information [Status display] You can call up on-screen menus, and conduct a number of adjustments and settings using the operation buttons p.16 on the control panel (main unit side) and remote control. This displays information about the input signal, lamp use time, etc. Press the button twice (or press the CALL button on the remote control once).
Using the menu (Continued) ■ The image adjustment menu ■ The display setting menu Use this menu to adjust image-related items. Items that can be adjusted are marked with “Yes”, and those that cannot are marked with “No”. Use this menu to set screen display-related items.
Using the document camera Please read this chapter if the model you purchased includes a document camera. ■ Uninstalling the camera 1) Place the folded document 2) Slide the connect lever in camera with the bottom the direction of an arrow. side up. ■ Preparation of the document camera (when loading the camera) Status before preparation (When stowed) 1) Set up arm 3) Rotate arm 4) Raise camera head 2) Extend arm 3) Pressing the lock lever in the direction of an arrow, slide the document camera.
Using the document camera (Continued) ■ Image projection with the document camera 1 Place the document. 5 Adjust the focus using the focus ring on the camera head Rotate the focus ring to either NEAR or FAR, whichever is better in focusing. Set the document at the top of or the side of the projector. Turn the focusing ring to adjust the focus. • Near : 100 mm to 300 mm Far : 300 mm to 5 m 6 If the screen is too dark or too bright, use the 2 Press the CAMERA button, and select camera input.
Mainenance Using the document camera (Continued) Air filter cleaning ■ Locking the white balance The air filter prevents dust and debris from getting inside the projector. Never run the projector with the filter removed. It is recommended that the air filter is cleaned regularly. “Check the air filter for dirt.” is displayed every 100 hours.
Lens and main unit cleaning Lamp replacement (Continued) 3 Remove the lamp cover. WARNING • Request cleaning and maintenance of a ceiling-mounted unit from your projector dealership. ■ Lens cleaning • Clean the lens with a commercially available blower and/or lens cleaner. • The lens is easily scratched, so do not rub it with hard objects, or strike it. ■ Main unit cleaning • Clean the main unit after unplugging the power cord. • Wipe dirt off the main unit gently with a soft cloth.
Others Trouble indications Before calling service personnel The indicator lights inform you of internal abnormalities. If you think something is wrong, check the followings before contacting customer service. Please see “Trouble indications” p.42 as well. TEMP LAMP ON No power ⇒ Problem with projector • Unplug the power cord, and contact your dealer.
Before calling service personnel (Continued) If This Happens Check The images from the document camera are blurry • Is the document imaging camera’s lens dirty? • Is the document imaging camera out of focus? p.37 • Is the location of the object being focused too dark? The images from the document camera are flickering • Is there impact from the room’s fluorescent lighting? Turn off the fluorescent lights, or change the shutter speed settings.
Specifications (Continued) ■ List of supported signals (Y/PB/PR signals) This projector supports the following RGB signals. Note, however, that depending on the computer model, the screen may show flicker or streaking. Please adjust the projector if this happens. (Press the AUTO SET button, and adjust automatically or manually. p.
Specifications (Continued) ■ CONTROL terminal ● Pin assignment 7 6 8 5 3 4 2 1 Pin No. 1 2 3 4 5 6 7 8 Signal Name RXD CTS DSR GND RTS N.C TXD N.
