3LCD DATA PROJECTOR TLP-T700 TLP-T701 TLP-T600 TLP-T601 TLP-T500 TLP-T501 TLP-T400 TLP-T401 TLP-S200 TLP-S201 (XGA / High Brightness / With PC Card Slot) Before Using OWNER’S MANUAL (XGA / With PC Card Slot & Document Camera) (XGA) (XGA / With Document Camera) (SVGA) (SVGA / With Document Camera) FAN AUTO SET TEMP LAMP VOL.- ON + VOL.
The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to the presence of uninsulated "dangerous voltage" within the product's enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons. The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance.
5. Heat 8. Power-Cord Protection The product should be situated away from heat sources such as radiators, heat registers, stoves, or other products (including amplifiers) that produce heat. Power-supply cords should be routed so that they are not likely to be walked on or pinched by items placed upon or against them, paying particular attention to cords at plugs, convenience receptacles, and the point where they exit from the product. 6. Water and Moisture 11. Object and Liquid Entry 14.
16. Damage Requiring Service 18. Servicing Unplug this product from the wall outlet and refer servicing to qualified service personnel under the following conditions: a) When the power-supply cord or plug is damaged. b) If liquid has been spilled, or objects have fallen into the product. c) If the product has been exposed to rain or water. d) If the product does not operate normally by following the operating instructions.
POWER SUPPLY CORD SELECTION If your line voltage is 220 to 240V, use one of the following types of cable. Plug configuration Plug type CAUTION Label MODEL NO. / RATING Label Plug configuration Line voltage EURO 220 – 240V UK 220 – 240V Line voltage Australian 240V 10A 200 – 240V Switzerland 240V 6A 200 – 240V SERIAL NO. Label MANUFACTURED; 310W 2.8 Plug type SERIAL NO. WARNING Label 1.4A CAUTION Label Use a 5A fuse which is approved by ASTA or BSI to BSI362.
Do not use volatile liquids, such as an insect spray, near the unit. Do not leave rubber or plastic products touching the unit for a long time. They will leave marks on the finish. If cleaning with a chemically saturated cloth, be sure to follow the product's precautions. Wireless LAN PC Card (Models equipped with PC card slot) • Do not connect the supplied wireless LAN PC card to devices other than this unit. Doing so could cause malfunction.
Before Using SAFETY PRECAUTIONS .................................................................................. IMPORTANT SAFETY INSTRUCTIONS ........................................................... LABEL LOCATIONS .......................................................................................... POWER SUPPLY CORD SELECTION .............................................................. IMPORTANT PRECAUTIONS ...........................................................................
Checking the package contents Names of each part on the main unit Please make sure that the following items are included in the box, along with the main unit. If an item is missing, please contact the store from which you purchased the product immediately. (6) (5) (4) (3) (2) (1) (17) VOL.
Names of each part on the control panel and remote control Control panel Remote Control Front (1) INPUT AUTO KEYSTONE VOL.- VOL.- VOL.+ PJ MODE LASER (18) (5) R-CLICK TEMP LAMP ON (12) (5) (13) (14) INPUT (2) (4) (7) (8) (9) (10) (3) (1) AUTO SET FREEZE AUTO KEYSTONE ON/ STANDBY MUTE RESIZE OFF (15) LA SE R (16) UT RE SIZ E OF F SE T FR EE ZE MU TE BY AU TO KEYSAUTO TONE ON STA/ ND ME L.
Names of the connection terminals ■ Removing the connection terminal cover (4) Press on the circle (“O”) while sliding the cover in the direction of the arrow. The cover will come off. (3) Preparing and using the remote control (1) (2) ■ Loading dry-cell batteries into the remote control ■ Operating the remote control Point the remote control toward the projector’s infrared remote sensor, and press a button on the remote control. q Remove the battery cover.
Preparing and using the remote control (Continued) Placement ■ Switching operation modes Placement Styles Operation modes should be switched between projector operation and computer operation. As shown in the figures below, this device can be placed in 4 different styles. The factory setting is “floor-mounted front projection.” Set the placement style in the default setting menu p.53 , in accordance with your needs.
How to use the PC card slot Before connection Please read this chapter if the model you purchased includes a PC card slot. The attached wireless LAN PC card enables you to connect the projector wirelessly with a personal computer that supports IEEE802.11b based wireless LAN. Please note that communication between all the computers based on IEEE802.11b and this projector is not guaranteed. p.33 You can also use a commercially available memory card to project JPEG image files using this projector. p.
Installing the applications Turning the power on and off Please read this chapter if the model you purchased includes a PC card slot. Connecting the power cord If you will use the supplied wireless LAN PC card function, install the application on the supplied CD-ROM onto your computer. 1 2 Insert the power cord connector into the AC IN socket of the projector. Insert the power cord plug into a wall or other power outlet.
Basic operations Turning the power on and off (Continued) Turning the power off Preparations 1 • Place the projector, and correctly connect all devices. Remote Control • To operate via the remote control, [PJ MODE] p.20 must be selected. Press the PJ MODE button. The button lights up. This light [PJ MODE] will go out 30 seconds after operations are complete. If Lights up necessary, press the button again. Press the ON/STANDBY button.
Using handy features Basic operations (Continued) 5 Projector placement angle adjustments The placement angle and the height of the projected image can be adjusted by the foot adjuster. ■ Using auto setting (Auto setting) 1 This function sets up the projector to the optimum state for each type of the input signal by using simple operations. The foot adjuster extends. Release the button to lock the position. 1 Press the AUTO SET button. w Turn the foot adjuster to fine-tune the angle.
Using handy features (Continued) ■ Freezing the image (Freeze) ■ Correcting the keystone distortion (Keystone) When the foot adjuster p.28 is used to change the projection angle, the picture will undergo keystone (trapezoidal) distortion. This projector is capable of correcting this keystone distortion. Control panel INPUT Remote Control ON/STANDBY VOL.+ VOL.- AUTO KEYSTONE PJ MODE LASER MENU / ENTER MENU R-CLICK INPUT Before correction After correction AUTO SET VOL.+ VOL.
Using handy features (Continued) Using the wireless LAN PC card ■ Displaying Information [Status display] Please read this chapter if the model you purchased includes a PC card slot. ■ Functions Yes Yes Yes No No No No No No Yes Yes No No No No No No Yes Yes No No No No No No Yes Yes Yes [Note 6] Yes [Note 6] Yes [Note 6] Yes [Note 6] Yes [Note 6] Yes [Note 6] Yes Yes No No No No No No Notes 1: The mode of supported RGB signals p.68 is shown. 2: Same as the refresh rate of the computer signal.
Using the wireless LAN PC card (Continued) ● Mount the supplied wireless LAN PC card into the projector, and select PC card input Referring to “Mounting a PC card,” p.23 mount the supplied wireless LAN PC card, then select PC card input in accordance with “Select input” p.27 . ● Projector settings The factory settings can be used as-is. If necessary, conduct the following settings, referring to “How to use the menu” p.52 and “The PC card setting menu” p.54 .
Using the wireless LAN PC card (Continued) 4 Select the screen image you wish the projector to display. Select Desktop The computer screen image is transmitted as-is. Select application window Select a running application (e.g. Microsoft® PowerPoint®), and send that application’s window only. ■ Displaying a JPEG image saved on a computer via the projector 1 Launch the Wireless Utility software application. The Screen image transmission mode window appears on the computer’s screen.
Using the wireless LAN PC card (Continued) 5 Select the projector to be transmitted. A list of the MAC addresses of the wireless LAN PC cards p.32 , p.59 mounted on the projectors that are available for transmission appears. If projector name has been set up already, it is shown instead of the MAC address. Select the checkbox of the projector to be transmitted to from is displayed on the this list. Then icon projector’s screen for few seconds. It is possible to select up-to four projectors.
Projecting images stored in a memory PC card Please read this chapter if the model you purchased includes a PC card slot. ■ JPEG files Models equipped with PC card slot are able to read JPEG files stored on a memory PC card, and display them on the screen. This allows you to give presentations without a computer, create advertising screen board using the auto slide show function, and more. (It is not possible to reproduce animation effects, such as those produced by Microsoft® PowerPoint®.
Projecting images stored in a memory PC card (Continued) Indicates that only folders are inside the folder. Indicates that an unsupported JPEG or other file is present. Indicates that the JPEG or other file is not supported. Indicates a folder for files taken/ stored by the document camera. p.50 Indicates that there is no data to be displayed in the folder. The following functions can be used via remote control operation and menu settings.
Using the document camera Please read this chapter if the model you purchased includes a document camera. ■ Preparation of the document camera • The input returns to the previous input when the CAMERA button is pressed again. • Camera input can also be selected by pressing the remote control or camera’s INPUT button. 2) Extend arm 1) Set up arm 3 Press the CAMERA button, and select camera input. Status before preparation (When stowed) W.
Using the document camera (Continued) ■ Using the overlay function 2 Press the W.BALANCE button. The LOCK indicator lights. The white balance is locked. The white balance returns to automatic adjustment when pressing the W.BALANCE button again. Then LOCK indicator goes out. The overlay function can be used to write over computer or video input images. Have a piece of white paper, and a red or blue pen ready.
Using the document camera (Continued) ■ Sending the camera’s images to a computer (Models equipped with PC card slot) Models equipped with a PC card slot can use a wireless LAN PC card to send images taken with the document camera to a computer in JPEG format, and open them, or save them to disk. 1 Preparing the computer and projector • Mount the supplied wireless LAN PC card referring to “Mounting a PC card” p.23 , and select PC card input in accordance with “Select input” p.27 .
Using the document camera (Continued) Operating a computer using the remote control ■ Storing the camera images into the memory PC card (Models equipped with PC card slot) A computer can be operated using the projector’s remote control. This function is available on any computer with the Windows 98/98SE, Windows Me, Windows 2000, or Windows XP OS, that is equipped with a USB port (The mouse remote control is not supported on OS 9 or OS X for the Macintosh).
Using the menus You can call up on-screen menus, and conduct a number of adjustments and settings, using the operation buttons p.16 on the control panel (main unit side) and remote control. ■ How to use the menus 1. Start Use this menu to adjust image-related items. Items Items that can be adjusted are marked with “Yes”, and those that cannot are marked with “No”. Display the Setting display menu Item 2.
Using the menu (Continued) ■ The display setting menu ● When the wireless LAN PC card is being used Use this menu to set screen display-related items. Item Input select mode Manual Description Item Description Auto (Switch to PC card input when the PC card is inserted) Transmission mode Ad hoc Screen size Infrastructure Channel This item cannot be changed currently. This is function for the future.
Air filter cleaning Lens and main unit cleaning The air filter prevents dust and debris from getting inside the projector. Never run the projector with the filter removed. It is recommended that the air filter is cleaned regularly. (A recommended measure is about once for every 50 hours of use.) ■ Lens cleaning • Clean the lens with a commercially available blower and/or lens cleaner. • The lens is easily scratched, so do not rub it with hard objects, or strike it.
How to use the supplied software Lamp replacement (Continued) 3 Remove the lamp cover. 3 This chapter briefly describes how to use supplied software applications other than the Wireless utility. 2 ■ How to use the Projector Configuration Tool The Projector Configuration Tool is a software utility that allows you to set up the projector for Infrastructure mode communications using a wireless LAN PC card. When using this application for the first time, conduct Preparation p.
How to use the supplied software (Continued) ■ How to use the JPEG Conversion Tool [Channel] This item cannot be changed currently. [Encryption] Click on the button to select [Off], [64 bit], or [128 bit]. [Key] This accepts input if Encryption is set to other than Off (input is required). Input a value from the keyboard. [Communication mode] Select Infrastructure by clicking the button. [SSID] This is an ID code for connecting to specific individuals over a wireless LAN.
How to use the supplied software (Continued) ● Converting files created with Microsoft® PowerPoint® Making a presentation with converted JPEG files This process provides presentations without using a computer by converting presentation files created with Microsoft® PowerPoint® into JPEG files, storing them on a memory PC card, and displaying them in a slide show. • To use this conversion mode, Microsoft® PowerPoint® must be installed on the computer. • Only static images are supported by this process.
Trouble indications Before calling service personnel The indicator lights inform you of internal abnormalities. If you think something is wrong, check the following before contacting customer service. Please see “Trouble indications” p.64 as well. TEMP LAMP or FAN TEMP LAMP ON No power ⇒ Problem with projector • Unplug the power cord, and contact your dealer. (Off) (Red lit) ON Lamp went out during use, or won’t come on ⇒ Returns to standby after about 2 minutes.
If This Happens Check Mouse remote control doesn't work • Are the USB cable and mouse remote control receiver (Models equipped with PC card slot) correctly connected? p.51 • Do your computer and OS support USB? • Is the remote control in [PC Mode]? p.
Specifications (Continued) ■ List of supported signals (Y/PB/PR signals) This projector supports the following RGB signals. Note, however, that depending on the computer model, the screen may show flicker or streaking. Please adjust the projector if this happens. (Press the AUTO SET button, and adjust automatically or manually. p.
Specifications (Continued) ■ CONTROL terminal ● Pin assignment 1 Pin No. 1 2 3 4 5 6 7 8 2 4 3 5 6 8 7 Signal Name RXD CTS DSR GND RTS N.C TXD N.
