Dear Customer, Thank you for purchasing this Toshiba LCD TV / DVD combination. This manual will help you use the many exciting features of your new LCD TV / DVD combination. Before operating your LCD TV / DVD combination, please read this manual completely, and keep it nearby for future reference. Safety Precautions WARNING: TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE. WARNING RISK OF ELECTRIC SHOCK DO NOT OPEN.
• ALWAYS turn off the TV and unplug the power cord to avoid possible electric shock or fire. • NEVER allow your body to come in contact with any broken glass or liquid from the damaged television. The LCD panel inside the TV contains glass and a toxic liquid. If the liquid comes in contact with your mouth or eyes, or your skin is cut by broken glass, rinse the affected area thoroughly with water and consult your doctor.
23) DANGER: RISK OF SERIOUS PERSONAL INJURY, DEATH, OR EQUIPMENT DAMAGE! Never place the TV on an unstable cart, stand, or table. The TV may fall, causing serious personal injury, death, or serious damage to the TV. 24) To avoid damage to this product, never place or store the TV in direct sunlight; hot, humid areas; or areas subject to excessive dust or vibration. 25) Always place the TV on the floor or a sturdy, level, stable surface that can support the weight of the TV.
37) WARNING: RISK OF ELECTRIC SHOCK! Never spill liquids or push objects of any kind into the TV cabinet slots. 38) While it is thundering, do not touch the connecting cables or apparatus. 39) For added protection of your TV from lightning and power surges, always unplug the power cord and disconnect the antenna from the TV if you leave the TV unattended or unused for long periods of time. 40) ALWAYS unplug the TV to completely disconnect from mains power.
Removing the Pedestal Stand 1) Carefully lay the front of the TV face down on a flat, cushioned surface such as a quilt or blanket. Leave the stand protruding over the edge of the surface. Note: Extreme care should always be used when removing the pedestal stand to avoid damage to the LCD panel. 2) Remove the four screws shown in the below diagram. This will allow removal of the pedestal stand.
Notes on copyright Notes on discs On handling discs • Do not touch the playback side of the disc. Handle the disc as shown in the figure below. Playback side • Do not attach paper or tape to discs. On cleaning discs • Fingerprints and dust on the disc cause picture and sound deterioration. Wipe the disc from the center outwards with a soft cloth. Always keep the disc clean.
Playable discs This LCD TV / DVD combination can play the following discs. Disc mark Contents Disc size Maximum playback time Approx. 4 hours (single sided disc) 12 cm Audio Approx. 8 hours DVD + (double sided disc) Video Video Approx. 80 minutes disc (moving pictures) 8 cm (single sided disc) Approx. 160 minutes (double sided disc) Audio 12 cm Approx. 74 minutes (single sided disc) + Video Video CD DIGITAL VIDEO (moving 20 minutes 8 cm Approx. (single sided disc) pictures) 74 minutes 12 cm Approx.
ENERGY STAR® User Information (only for 19/24’’) ENERGY STAR User Information Statement: the factory default settings of this television meet ENERGY STAR requirements. Changing Picture Settings may increase energy consumption, possibly beyond the limits required for ENERGY STAR qualification. To ensure your television is operating at optimal energy efficiency, select [Home] mode during initial activation. To return to [Home] mode settings, select [Standard] picture mode.
Contents Important Safety Instructions...........................................3 Installation, Care, and Service.........................................3 Choosing a location for your LCD TV / DVD combination.............5 Notes on discs...................................................................................7 Chapter 1: Introduction................................................ 11 Features of your new TV.................................................................
Chapter 1: Introduction Features of your new TV The following are just a few of the many exciting features of your new Toshiba widescreen, integrated HD, LCD TV / DVD combination: • Integrated digital tuning (8VSB ATSC and QAM) eliminates the need for a separate digital converter set-top box (in most cases). • 1366 x 768 output resolution. (19SLV411U, 32SLV411U) • 1920 x 1080 output resolution. (24SLV411U) • Two HDMI® digital, high-definition multimedia interfaces 1080p input support ( page 17).
Chapter 1: Introduction TV front, top and side panel controls and connections 19SLV411U / 24SLV411U / 32SLV411U Left side panel TV front 4 5 3 6 7 8 9 10 2 1無 2無 3無 4無 5無 6無 7無 8無 1 Power On / Standby LED — Power LED (Green) = Power indicator Power LED (Red) = Power standby Remote sensor (embedded) — Point the remote control toward this remote sensor. Effective range: Disc slot — Load the disc, with label facing forward, into the disc slot to view or listen. EJECT — Press to eject the disc.
Chapter 1: Introduction TV back panel connections For an explanation of cable types and connections see pages 14-20. 19SLV411U 1 7 2 3 8 Power cord 4 5 6 32SLV411U (Please use this illustration for 24SLV411U model.) 1 7 8 2 Power cord 1無 2無 4 3 ® AUDIO/COLOR STREAM HD — ColorStream high-definition component video inputs (with standard stereo audio inputs) for connecting devices with component video output, such as a Toshiba DVD player with ColorStream®.
Chapter 2: Connecting your TV Overview of cable types Optical audio cable Cables can be purchased from most stores that sell audio/video devices. Before purchasing any cables, be sure of connector types required by your devices and the length of each cable. Optical audio cable is for connecting receivers with Dolby Digital or PCM (Pulse-Code Modulation) optical audio input to the TV’s DIGITAL AUDIO OUT terminal ( page 19).
Chapter 2: Connecting your TV Connecting a VCR, and antenna, Cable TV Connecting a camcorder Ye l l o w White Red Red Ye l l o w White Ye l l o w Red White Red White Ye l l o w You will need: • standard A/V cables To view the camcorder video: You will need: Select the VIDEO video input source on the TV.
Chapter 2: Connecting your TV Connecting a DVD player with ColorStream® (component video) Connecting a satellite receiver Green Blue Red Blue Green Red White White Red Red Green Red −− If your DVD player does not have component video, connect a standard A/V cable to AUDIO/VIDEO terminal. If your DVD player has HDMI video, see page 17. To view the DVD player: Turn ON the DVD player. Select the ColorStream HD video input source on the TV.* remote control ( page 30).
Chapter 2: Connecting your TV Connecting an HDMI or DVI device to the HDMI® input To view the HDMI device video: The HDMI input on your TV receives digital audio and uncompressed digital video from an HDMI source device, or uncompressed digital video from a DVI (Digital Visual Interface) source device.
Chapter 2: Connecting your TV REGZA-LINK® connection You can control the basic functions of connected audio/video devices using the TV’s remote control if you connect a REGZA-LINK® compatible audio receiver or playback device. For an explanation of setup and operations, see pages 50-51. TV back panel Audio receiver Playback device (REGZA-LINK® DVD player,etc.) Playback device (REGZA-LINK® DVD player,etc.
Chapter 2: Connecting your TV Connecting a digital audio system The TV’s DIGITAL AUDIO OUT terminal outputs a Dolby® * Digital or 2-channel down-mixed PCM (Pulse-Code Modulation) signal for use with an external Dolby® Digital decoder or other external audio system with optical audio input. 5無 Press t or u to select either Dolby Digital or PCM, depending on your device. ( “Selecting the optical audio output format” on page 40).
Chapter 2: Connecting your TV Connecting a personal computer (PC) With either the PC IN or HDMI connection, you can watch your computer’s display on the TV and hear the sound from the TV’s speakers. To connect a PC to the PC IN terminal on the TV: When connecting a PC to the PC IN terminal on the TV, use an analog RGB (15-pin) computer cable and a PC audio cable. • Signal names for mini D-sub 15-pin connector Pin No. Signal name Pin No. Signal name Pin No.
Chapter 3: Using the remote control Preparing the remote control for use The remote control can operate your LCD TV / DVD combination and control the basic functions of connected audio/video devices if you connect a REGZA-LINK® compatible audio receiver or playback device ( page 50). Installing the remote control batteries 1無 Open the battery lid at the bottom of remote controller. Push! 2無 Insert the batteries, corresponding to the (+) and (-) markings on the battery compartment.
Chapter 3: Using the remote control Learning about the remote control The buttons used for operating the LCD TV / DVD combination are described here. For the REGZALINK® remote control functions, see the section “ Using REGZA-LINK® ” ( page 50). turns the TV on and off. When the TV is 1無 POWER on, the power LED indicator on the TV front will be illuminated in green. 2無 EJECT 3無 TV/DVD ejects the disc from the disc slot. switches to TV or DVD mode. TV/DVD 4無 FREEZE FREEZE freezes the picture.
Chapter 3: Using the remote control 23無 Arrow buttons (pqtu) When a menu is on-screen, these buttons select or adjust programming menus. (Also see t / u.) 24無 CANCEL / EXIT closes on-screen menus. accesses the top menu of DVDs that 25無 TOP MENU contain two or more titles( page 60). begins playback of the loaded disc 26無 PLAY ( page 55). stops playback of the loaded disc 27無 STOP ( page 55). suspends disc playback temporarily or 28無 PAUSE plays back disc frame by frame ( pages 55, 56).
Chapter 4: Menu layout and navigation Main menu layout The tables below and on the next page provide a quick overview of your TV’s menu system. To open the main menus (illustrated below), press on the remote control or MENU on the TV control panel.
Chapter 4: Menu layout and navigation Setup / Installation menu layout The Installation menu contains the Terrestrial and System Status menus. To open the Installation menu (illustrated below), press panel, open the Setup menu, select Installation, and press Icon Terrestrial on the remote control or MENU on the TV control .
Chapter 5: Setting up your TV Initial Setup When you first turn on or reset the TV, the Initial Setup window will appear. 1無 In the Menu Language field, press t or u to select your preferred language. 2無 Press p or q to select Time Zone Setup and set your desired time zone with t or u and press . 3無 Next, the Location setting window will appear. For normal home use, press t or u to select Home and press . 4無 Next, ANT/CABLE In setup window will appear.
Chapter 5: Setting up your TV Note: •• You must configure the ANT/CABLE input source before programming channels ( page 26). •• The automatic channel programming process will erase channels that were previously programmed into the TV’s memory. •• To tune the TV to a channel not programmed in the channel memory, you must use the Channel Number buttons on the remote control.
Chapter 5: Setting up your TV To manually add digital subchannels on a physical channel: Setting the HDMI® audio mode Use the Channel Numbers and the Dash ( ) on the remote control to enter the channel number (for example, 56–1). If the channel is found, the number will be added to the list and the box will be unchecked. If the channel is not found, a message will appear.
Chapter 5: Setting up your TV Viewing the digital signal meter You can view the digital signal meter in the ANT/ CABLE digital TV input source only. To view the digital signal meter: 1無 Press and open the Setup menu. 2無 Highlight Installation and press . 3無 A new set of Installation menu icons will appear. Open the Terrestrial menu, highlight Signal Meter, and press . 4無 Press pqtu to select the antenna input and digital channel whose signal you want to check.
Chapter 6: Using the TV’s features Selecting the video input source to view To select the video input source to view: 1無 Press INPUT on the remote control or TV control panel. 2無 And then either: a) Press 0–6 ; or b) Repeatedly press on the remote control and then press to change the input; or c) Repeatedly press INPUT on the remote control or TV control panel to change the input. The current signal source displays in the top right corner of the Input Selection screen.
Chapter 6: Using the TV’s features 3無 Press or to highlight the video source you want to label. Tuning channels Tuning channels using the Channel Browser™ 4無 Press or to select the desired label for that input source. If a particular input is not used, you can select Hide as the label, which will cause that input to be “grayed out” in the Input Selection screen and skipped over when you press INPUT on the remote control. 5無 To save the new input labels, highlight Done and press .
Chapter 6: Using the TV’s features Elements of the Channel Browser™ 3無 Press to highlight History List, and then press or to select the setting you prefer: either On, or Off. Note: History List will be cleared every time the TV is powered off. 4無 Press to highlight ANT/CABLE List, and then press or to select On or Off.
Chapter 6: Using the TV’s features To tune to a channel or input in Select mode: Setting the Channel Tuning Mode 1無 While watching TV, press This feature allows you to choose how tuning will be handled for analog and digital channels when the TV is in Antenna mode. or to open the Channel Browser™ and surf back to a previous item or forward to the next item in the list.
Chapter 6: Using the TV’s features Tuning to the next programmed channel Switching between two channels using SurfLock™ To tune to the next programmed channel: The SurfLock™ feature temporarily “memorizes” one channel to the button, so you can return to that channel quickly from any other channel by pressing . Press panel. or on the remote control or TV control Note: This feature will not work unless you program channels into the TV’s channel memory ( page 26).
Chapter 6: Using the TV’s features To select the picture size using the menus: 1無 Select Picture Size in the Theater Settings menu. 2無 Press or to select the desired picture size setting. 3無 Highlight Done and press . Note: Some of the picture sizes may not be available depending on the receiving signal format (those will be “grayed out” in the Picture Size screen). Using these functions to change the picture size (i.e.
Chapter 6: Using the TV’s features Picture Size 4:3 Some program formats will display with sidebars and/or bars at the top and bottom. To set the scroll settings: 1無 Press and open the Picture menu. 2無 Highlight Theater Settings and press . 3無 In the Picture Size field, select either Normal TheaterWide 2 or TheaterWide 3 (you cannot scroll in any other mode). 4無 Press to highlight the Picture Scroll field.
Chapter 6: Using the TV’s features To turn on the auto aspect ratio feature: 1無 Press and open the Picture menu. 2無 Highlight Theater Settings and press . 3無 In the Auto Aspect Ratio field, select On. 4無 To save the new settings, highlight Done and press . To revert to the factory defaults, highlight Reset and press . To turn off the auto aspect ratio feature: Adjusting the picture Selecting the picture mode You can select your desired picture settings from four different modes, as described below.
Chapter 6: Using the TV’s features Adjusting the picture quality Using the closed caption mode You can adjust the picture quality (Contrast, Backlight, DynaLight™, Brightness, Color, Tint, and Sharpness.) to your personal preferences.
Chapter 6: Using the TV’s features Digital CC Settings You can customize the closed caption display characteristics by changing the background color, opacity, text size, type, edge, and color. Note: ••This feature is available for digital channels only. ••You cannot set the Caption Text and Background as the same color. To customize the closed captions: 1無 Press and open the Preferences menu. 2無 Highlight Digital CC Settings and press .
Chapter 6: Using the TV’s features Selecting stereo / SAP broadcasts Using the MTS button The multi-channel TV sound (MTS) feature allows you to output high-fidelity stereo sound. MTS also can transmit a second audio program (SAP) containing a second language, music or other audio information (when provided by individual stations). When the TV receives a stereo or SAP broadcast, the symbol “ ” or word “SAP” appears onscreen when is pressed.
Chapter 6: Using the TV’s features Using the Dolby® Digital Dynamic Range Control feature Number buttons to enter a new four-digit code, enter the code a second time to confirm, and press . This dynamic range control feature causes Dolby Digital dynamic range to be further compressed, allowing you to switch from digital to analog broadcasts at the same dynamic range. To use the Dolby Digital Dynamic Range Control: 1無 Press and open the Sound menu. 2無 Highlight Audio Setup and press .
Chapter 6: Using the TV’s features To block and unblock TV programs and movies: To download the additional rating system (if available): 1無 Press and highlight the Locks menu icon. 2無 Press to display the PIN code entering screen. 3無 Enter your four-digit PIN code and press . 4無 Press to highlight Enable Rating Blocking. 5無 Press to select On. 1無 Press and highlight the Locks menu icon. 2無 Press to display the PIN code entering screen. 3無 Enter your four-digit PIN code and press .
Chapter 6: Using the TV’s features Independent rating system for broadcasters Ratings Description and Content themes TV-MA Mature Audience Only (This program is specifically designed to be viewed by adults and may be unsuitable for children under 17.) L) Crude or indecent language S) Explicit sexual activity V) Graphic violence TV-14 Parents Strongly Cautioned (This program contains some material that many parents would find unsuitable for children under 14.
Chapter 6: Using the TV’s features Unlocking programs temporarily If you try to tune the TV to a program that exceeds the rating limits you set, the TV will enter program lock mode and the following message will appear onscreen: This program exceeds the rating limit you set. Push 'MUTE' to enter PIN. To lock channels: 1無 From the Setup menu, highlight Installation and press 2無 Press . to select Terrestrial. 3無 Press or to select Channel Options and press . The list of channels will appear.
Chapter 6: Using the TV’s features Using the panel lock feature You can lock the control panel to prevent your settings from being changed accidentally (by children, for example). When the Panel Lock is On, none of the controls on the TV control panel will operate except POWER. 4無 Press or to highlight the item you want to adjust. 5無 Press or to make the appropriate adjustments. To lock the control panel: 1無 Press and highlight the Locks menu icon.
Chapter 6: Using the TV’s features Using the Media Player Using the Media Player with USB You can enjoy photos or music contents stored on a USB storage device. Photo Viewer specifications: Data type: JPEG Exif ver2.
Chapter 6: Using the TV’s features Viewing photo files 1無 To start slide show, press There are three types of view modes. 2無 Press or to view the previous or next photo. Multi View: This view allows you to search for photos in a grid format. These pictures are displayed using thumbnail data in each image file. in the Single View mode. To set Interval Time and Repeat settings: 1無 Press to open the Quick Menu. 2無 Press or to select either Interval Time or Repeat.
Chapter 6: Using the TV’s features During playback • Press to pause. • To normal playback, press or • To locate a specific file, press • To adjust volume , press / repeatedly. . Note: During playback, you can adjust the SOUND menu functions from the Quick Menu. To set the repeat mode: 1無 Press to open the Quick Menu. 2無 Highlight Repeat, and press or to select Off, All or 1. 3無 Press . To close the Music Player 1無 Press .
Chapter 6: Using the TV’s features Contents Description Description To cancel the sleep timer: Music Music list (Multi View) See page 47. Repeatedly press until it is set to 0 minute. Sorting To sort the folders and files 1無 Press to open the Quick Menu. 2無 Press or to select Sort. 3無 Press or to select Title, New or Old to set the sorting rule. Playback See page 47. Pause See page 48. Stop See page 47. Skip See page 48. Repeat play See page 48. SOUND Settings See page 40.
Chapter 6: Using the TV’s features Using REGZA-LINK® REGZA-LINK Player Control menu functions: This is a new feature that uses CEC technology and allows you to control Toshiba REGZA-LINK® compatible devices from the TV remote via HDMI connection ( page 18). When the Enable REGZA-LINK in the REGZA-LINK Setup menu is set to On, the following REGZALINK® functions will be enabled. 1無 Press and open the Preferences menu.
Chapter 6: Using the TV’s features VOLUME and MUTE controls of Audio Receiver With your TV’s remote control, you can adjust or mute the sound volume of the Audio Receiver. • / adjust the volume level. • turns off the sound. Note: When you turn on the Audio Receiver, change its input source or adjust the sound volume, the sound will be output from the audio receiver’s speakers even if TV Speakers has been selected. Turn the TV off and on again to output the sound from the TV speakers.
Chapter 6: Using the TV’s features Displaying TV status information To display TV status information : Press on the remote control. The following information will display (if applicable): • Current input (ANT/CABLE, VIDEO, etc.) • If ANT/CABLE is the current input, either “CABLE” (for cable TV) or “ANT” (for over-the-air broadcasts).
Chapter 7: Using the TV’s advanced features Selecting the Color Temperature Using the advanced picture settings features You can change the quality of the picture by selecting from three preset Color Temperatures (Cool, Medium, and Warm), as described below. Using Dynamic Contrast Dynamic Contrast detects changes in picture quality that affect the appearance of your contrast settings and then automatically adjusts the video.
Chapter 7: Using the TV’s advanced features Using CableClear® digital Noise Reduction The CableClear® digital Noise Reduction feature allows you to reduce visible interference in your TV picture. This may be useful when receiving a broadcast with a weak signal (especially a Cable channel) or playing a noisy video cassette or disc. To change the CableClear settings: 1無 Press and open the Picture menu, highlight Noise Reduction and press . 2無 In the CableClear field, select your desired setting.
Chapter 8: Basic disc playback Disc playback This section shows you the basics on how to play a disc. Basic playback (DVD/VCD/CD)* 1無 Press POWER on the TV control panel or on the remote control. The Power LED on the front of the LCD TV / DVD combination changes to green. It may take approximately 10 seconds for a picture to appear on-screen. When using an amplifier, switch on the amplifier. 2無 Press TV/DVD on the remote control to switch to DVD mode. The DVD start-up screen will appear on-screen.
Chapter 8: Basic disc playback •• In some instances the LCD TV / DVD combination may take a minute or so to start disc playback. •• When you load a disc with the playback side facing backward, “Reading” appears on-screen but it will be replaced by “Incorrect Disc”. Eject the disc and load it again making sure the playback side is now facing forward. •• The playback resume function may not work on some discs. •• Some DVDs may have fixed playback operations designed by the DVD manufacturer.
Chapter 9: Advanced disc playback Zoom function/Scene navigation You can change the viewing scale of a picture by using the Zoom function. Once the image has been rescaled, use the arrow buttons to pan the image. Scene navigation options differ depending on the kind of disc. DVDs use the title, chapter or record time to locate the start point for playback. Audio CDs and Video CDs use the record time or track number. To view the discs title/track or chapter/ track list, press .
Chapter 9: Advanced disc playback Scene bookmark Repeat playback/A-B repeat Scene bookmarks refer to specific points in the playback range that have been marked for later access. You can create up to three markers per disc. Note: The saved scene bookmarks are only accessible during the current session. Once you eject the disc or turn off the LCD TV / DVD combination, all bookmarks will be cleared. You can choose to repeat DVD playback by title or chapter.
Chapter 9: Advanced disc playback Enabling A-B repeat mode (DVD/VCD/ CD) 1無 During playback, press at the point where you would like the playback loop to begin. This sets your “A” point. A 2無 When the playback reaches the point where you would like the playback loop to stop, press again. This sets your “B” point. A B The section between points A and B will be played repeatedly in a loop until you turn off the Repeat A-B mode. To resume normal playback: Press until Off appears on-screen.
Chapter 9: Advanced disc playback To resume normal playback: In step 2, set Mode to Normal. To change the program: 1. Set Mode to Program. 2. Press or , then or to select the playback position you want to change the track input for, then press . 3. Use the Channel Number buttons (0-9) to input the new track for the selected position. To remove a track from the programmed list: 1. Set Mode to Program. 2. Press or , then or to select the playback position, then press .
Chapter 9: Advanced disc playback Soundtrack language/Audio channel/Subtitle Playback information/VCD playback control Selecting a soundtrack language (DVD) Viewing the playback info (DVD/VCD) Press during playback. DVD mode You can select the soundtrack language when you play a multilingual DVD. Elapsed/remaining time Elapsed/remaining time for for current title current chapter During playback, press repeatedly until the preferred language track is selected.
Chapter 9: Advanced disc playback MP3, WMA, JPEG, and Audio CD operation This LCD TV / DVD combination can play MP3, WMA, and JPEG files recorded on a CD-R or CD-RW disc. To create the MP3/ WMA/ JPEG disc, you need a Windows PC with a CD-RW drive and file encoding software. You must use a Windows PC to create the MP3/WMA/JPEG disc. This LCD TV / DVD combination requires discs/recordings that meet certain technical standards in order to achieve optimal playback quality.
Chapter 9: Advanced disc playback About the file browser (CD) To view the previous or next thumbnail page: Press or . Playing an audio file (CD) 1無 Load an MP3/WMA/Audio CD in the disc slot. The file browser appears on-screen. It may automatically play by composition of an audio file.
Chapter 9: Advanced disc playback Viewing a JPEG file (CD) Viewing a slide show (CD) 1無 Load a disc containing JPEG files in the disc slot. If there are multiple JPEG files in the selected directory, you can view them in a slide show. For instructions on how to enable the slide show feature and set the interval period between pictures, go to page 69. The file browser appears on-screen. 2無 Press or to select an image file for view. A preview of the selected file is displayed in the Preview panel.
Chapter 9: Advanced disc playback MP3, WMA, JPEG and Audio CD playback modes You can choose to repeat CD playback by track or the entire disc. You can also program the file playback sequence or set the LCD TV / DVD combination to play files at random. Note: These playback modes are only applicable during the current session. Once you eject the disc or turn off the LCD TV / DVD combination, these modes will be disabled. Pressing or during playback will also cancel these modes.
Chapter 9: Advanced disc playback Programming the playback sequence (CD) 1無 In the Option panel of the file browser, press or to select Edit Mode, then press Folder-1 Folder-2 MP3-1 MP3-2 MP3-3 . . MP3-1 MP3-2 MP3-3 WMA-3 Edit Mode to select a file, then press to mark it for inclusion in the programmed playlist. A check mark will appear next to the file. In Program view, only the files you added in step 3 are displayed.
Chapter 10: Customizing disc playback Customizing disc playback You can customize the disc playback settings to suit your preferences. Configuring the disc playback settings (DVD/VCD/CD) 1無 In DVD mode, press during stop mode. Parental DRC E.B.L.
Chapter 10: Customizing disc playback Disc playback setup Tab Option Menu Subtitle Audio OSD Display Picture Mode JPEG Interval Night Mode Digital Out Parental Password Description Select the language for the DVD menu display. Select the subtitle language for disc playback. Select the audio language for disc playback. Select the language for the Setup screen display. Choose whether to show a status display whenever a button is pressed. Select the DVD source content.
Chapter 10: Customizing disc playback Parental DRC E.B.L. Menu Menu Display : Off :English Picture Subtitle ::Auto English QSoundMode Set Password On Audio Output Display :English : Interlace On JPEG Interval Audio Output OSD :English Picture Mode DivX(R) :VOD Auto JPEG Interval : 5 Seconds Screen Saver : On n Menu / n OSD Select the language for the DVD and Setup menu display. Options include: English, French, and Spanish.
Chapter 10: Customizing disc playback Night Nfov!Mode :Off ;!Fohmjti Digital Out :Bitstream !!!!!!!!!!!!!Tfu!Qbttxpse UW!Tdsffo! ;!5;4! Tvcujumf! ;!Fohmjti DRC Menu E.B.L.
Chapter 10: Customizing disc playback To temporarily cancel the parental restriction: 1) Load the restricted content DVD that you want to play. 2) Use the Channel Number buttons (0–9) to input the system password after the “Enter Password” message, then press . This suspension of the parental restriction setting applies until disc is ejected. n Password Select this option to change the access password for the parental control setting. 1) Press or to select Password, then press .
Chapter 11: Troubleshooting General troubleshooting Poor color or no color Before calling a service technician, please check this chapter for a possible cause of the problem and some solutions you can try. •• Adjust the Tint and/or Color ( page 38). Black box on-screen •• The station may have broadcast difficulties. Try another channel. Poor composite picture •• If the TV is connected to an external A/V device (e.g., DVD player, video game system, set-top box, etc.
Chapter 11: Troubleshooting Closed caption problems •• If the program or video you selected is not •• •• closed captioned, no captions will display ( page 38). If text is not available, a black rectangle may appear. If this happens, turn off the closed caption feature ( page 38). A closed-caption signal may not display correctly in the following situations: a) when a videotape has been dubbed; b) when the signal reception is weak; or c) when the signal reception is nonstandard ( page 38).
Chapter 12: Appendix Specifications Note: •• These models comply with the specifications listed below. •• Designs and specifications are subject to change without notice. •• These models may not be compatible with features and/or specifications that may be added in the future.
Chapter 12: Appendix Acceptable signal formats for PC IN and HDMI terminals PC IN signal formats Note: Depending on the connected PC, the following status may occur; incorrect display, false format detection, picture position failure, blur, or judder. But this is not a malfunction of your TV. Format Resolution V. Frequency H. Frequency Pixel Clock Frequency VGA 640 × 480 59.940Hz 31.469kHz 25.175MHz SVGA 800 × 600 60.317Hz 37.879kHz 40.000MHz XGA 1024 × 768 60.004Hz 48.363kHz 65.
Chapter 12: Appendix Limited United States Warranty for LCD TV/DVD Combination Toshiba America Information Systems, Inc. (“TAIS”) makes the following limited warranties to original consumers in the United States. THESE LIMITED WARRANTIES EXTEND TO THE ORIGINAL CONSUMER PURCHASER OR ANY PERSON RECEIVING THIS LCD TV/DVD COMBINATION AS A GIFT FROM THE ORIGINAL CONSUMER PURCHASER AND TO NO OTHER PURCHASER OR TRANSFEREE. LCD TV/ DVD COMBINATIONS PURCHASED IN THE U.S.A.
Chapter 12: Appendix THIS LIMITED WARRANTY GIVES YOU SPECIFIC LEGAL RIGHTS AND YOU MAY ALSO HAVE OTHER RIGHTS WHICH MAY VARY FROM STATE TO STATE IN THE U.S.A. SOME STATES OF THE U.S.A. DO NOT ALLOW LIMITATIONS ON THE DURATION OF AN IMPLIED WARRANTY, WHEN AN ACTION MAY BE BROUGHT, OR THE EXCLUSION OR LIMITATION OF INCIDENTAL OR CONSEQUENTIAL DAMAGES. THEREFORE, THE ABOVE PROVISIONS MAY NOT APPLY TO YOU UNDER SUCH CIRCUMSTANCES.
Chapter 12: Appendix CORPORATION, THEIR AFFILIATES, ADRs AND ASPs AND WHETHER MADE ORALLY OR IN WRITING (INCLUDING ANY STATEMENT IN ANY BROCHURE, PRESS RELEASE, ANNOUNCEMENT, ADVERTISEMENT, POINT OF SALE DISPLAY, ETC.). YOU MUST READ AND FOLLOW ALL SET-UP AND USAGE INSTRUCTIONS IN THE APPLICABLE USER GUIDES AND/OR MANUALS. IF YOU FAIL TO DO SO, THIS TELEVISION MAY NOT FUNCTION PROPERLY AND YOU MAY SUFFER DAMAGE.
Chapter 12: Appendix information, you find that service is needed, please contact TCL Customer Support toll free at 1 800 2683404. A copy of the GPL source code in this product may be obtained by contacting Toshiba Consumer Solutions at (800) 631-3811. There will be a charge to cover the costs of providing the source code. A copy of the LGPL source code in this product may be obtained by contacting Toshiba Consumer Solutions at (800) 631-3811.
Chapter 12: Appendix a whole at no charge to all third parties under the terms of this License.
Chapter 12: Appendix time. Such new versions will be similar in spirit to the present version, but may differ in detail to address new problems or concerns. Each version is given a distinguishing version number. If the Program specifies a version number of this License which applies to it and “any later version”, you have the option of following the terms and conditions either of that version or of any later version published by the Free Software Foundation.
Chapter 12: Appendix Authors: Simon-Pierre Cadieux Eric S. Raymond Gilles Vollant and with the following additions to the disclaimer: There is no warranty against interference with your enjoyment of the library or against infringement. There is no warranty that our efforts or the library will fulfill any of your particular purposes or needs. This library is provided with all faults, and the entire risk of satisfactory quality, performance, accuracy, and effort is with the user. libpng versions 0.
Note
TOSHIBA AMERICA INFORMATION SYSTEMS, INC. Corporate Headquaters: 9740 IRVINE BLVD.; IRVINE, CA 92618 U.S.A. Visual Products Service and Support Dept: 1420-B TOSHIBA DRIVE, LEBANON, TN 37087, U.S.A. . TOSHIBA OF CANADA LTD. HEAD OFFICE: 191 McNABB STREET, MARKHAM, ONTARIO, L3R 8H2, CANADA CableClear, ColorStream, GameTimer, and TheaterWide are registered trademarks of Toshiba America Information Systems, Inc.
