Integrated High Definition LED Television User’s Guide: 32L2200U 40L2200U 50L2200U If you need assistance: Toshiba's Support Web site support.toshiba.com Call Toshiba Customer Support Center: Within the United States at (800) 631-3811 Outside the United States at (949) 583-3050 For more information, see “Troubleshooting” on page 121 in this guide. Owner's Record The model number and serial number are on the back and side of your TV. Record these numbers in the spaces below.
Dear Customer, Thank you for purchasing this Toshiba LED TV. This manual will help you use the many exciting features of your new LED TV. Before operating your LED TV, carefully read this manual completely.
glass and a toxic liquid. If the liquid comes in contact with your mouth or eyes, or your skin is cut by broken glass, rinse the affected area thoroughly with water and contact your doctor immediately. • ALWAYS contact a service technician to inspect the TV any time it has been damaged or dropped. Important Safety Instructions 1) 2) 3) 4) Read these instructions. Keep these instructions. Heed all warnings. Follow all instructions. 5) Do not use this apparatus near water. 6) Clean only with dry cloth.
24) When selecting a location for the TV: • NEVER allow any part of the TV to hang over the edge of the supporting furniture. • NEVER place the TV on tall furniture (for example, entertainment centers or bookcases) without anchoring both the furniture and the TV to a suitable support. • NEVER place cloth or other material between the TV and the supporting furniture. • NEVER allow children to climb on the TV.
Choosing a location for your LED TV 38) WARNING: RISK OF ELECTRIC SHOCK! Never spill liquids or push objects of any kind into the TV cabinet slots. 39) During a lightening storm, do not touch the connecting cables or product. 40) For added protection of your TV from lightning and power surges, always unplug the power cord and disconnect the antenna from the TV if you leave the TV unattended or unused for long periods of time. 41) Always unplug the TV to completely disconnect from main power.
Note: Extreme care should always be used when removing the pedestal stand to avoid damage to the LCD panel. 2) Remove the screws shown in the below diagram. This will allow removal of the pedestal stand. 3) Once you have removed the screws holding the pedestal stand in place, remove the pedestal stand from the TV.
FCC Declaration of Conformity Compliance Statement (Part 15): Toshiba 32L2200U, 40L2200U, and 50L2200U Television models comply with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation. The party responsible for compliance to these rules is: Toshiba America Information Systems, Inc. 9740 Irvine Blvd.
Trademark Information Copyright • ClearFrame, CableClear, ColorStream, DynaLight, GameTimer, SurfLock are trademarks or registered trademarks of Toshiba America Information Systems, Inc. and/or Toshiba Corporation. This guide is copyrighted by Toshiba America Information Systems, Inc. with all rights reserved. Under the copyright laws, this guide cannot be reproduced in any form without the prior written permission of Toshiba.
Contents Chapter 1: Introduction.............................................................. 15 Features ..................................................................16 Overview of installation, setup, and use..................17 TV front and side panel controls and connections ......................................................18 TV back panel connections .....................................20 Chapter 2: Connecting Your TV................................................
Contents Connecting a Blu-ray™/DVD Player/Satellite receiver with ColorStream® (component video), or a VCR ...........................................................27 Connecting an HDMI® or DVI device to the HDMI® input................................................29 HDMI® CEC connection...........................................32 Connecting a digital audio system ..........................33 Connecting an analog audio system .......................35 Connecting a computer.........................
Contents 11 Labeling the video input sources ............................63 Tuning channels using the Channel Browser ..........65 Favorites browser .............................................66 Elements of the Channel Browser .....................67 Adding and clearing channels and inputs in the History List........................................69 Tuning to the next programmed channel ..........69 Tuning to a specific channel (programmed or unprogrammed)..........................................
Contents Using the digital audio selector.........................84 Selecting stereo/SAP broadcasts ......................85 Adjusting the audio quality................................86 Audyssey Premium Television™ (50L2200U only).........................................87 Stable Sound (32L2200U/40L2200U only) .......88 Selecting the optical audio output format .........88 Using the Dolby® Digital Dynamic Range Control feature ............................................89 Using the Locks menu ......
Contents 13 No Signal Power Down .........................................110 Using HDMI® CEC.................................................111 HDMI® CEC playback device (DVD player, etc.) control .........................111 Other HDMI® CEC functions............................113 Setting up HDMI® CEC....................................114 Displaying TV status information ..........................114 Understanding the Last Mode Memory feature .....115 Chapter 7: Using the TV’s Advanced Features .....
Contents Audio power....................................................128 Speaker type .........................................................128 Video/audio terminals ...........................................128 Video/audio input............................................128 ColorStream® (component video) HD input ....129 HDMI® input ...................................................129 Digital audio output.........................................129 PC input ..................................
Chapter 1 Introduction Safety icons This manual contains safety instructions that must be observed to avoid potential hazards that could result in personal injuries, damage to your equipment, or loss of data. These safety cautions have been classified according to the seriousness of the risk, and icons highlight these instructions as follows: Indicates an imminently hazardous situation which, if not avoided, will result in death or serious injury.
Introduction Features Features The following are just a few of the many exciting features of your new Toshiba wide screen, integrated HD, LED TV: ❖ Integrated digital tuning (8VSB ATSC and QAM)— Eliminates the need for a separate digital converter set-top box (in most cases). ❖ 1366 x 768 output resolution(32L2200U) ❖ 1920 x 1080 output resolution(40L2200U/50L2200U) ❖ Two HDMI®—Digital, High-Definition Multimedia Interfaces with 1080p input support.
Introduction Overview of installation, setup, and use 17 Overview of installation, setup, and use Follow these steps to set up your TV and begin using its many exciting features. 1 Carefully read the important safety, installation, care, and service information. Keep this manual for future reference. 2 To choose a location for the TV: ❖ Read “Important notes about your TV” on page 7. ❖ Place the TV on the floor or a sturdy, level, stable surface that can support the weight of the unit.
Introduction TV front and side panel controls and connections 10 Program channels into the TV’s channel memory. See “Auto Tuning” on page 53. 11 For details on using the TV’s features, see chapters 6 and 7. 12 For help, refer to “Troubleshooting” on page 121. 13 For technical specifications, see “Specifications” on page 127.
Introduction TV front and side panel controls and connections 19 3 POWER—Turns the TV On/Off. If the TV stops responding to the buttons on the remote control or TV control panel and you cannot turn off the TV, press and hold the POWER button on the TV control panel for a few seconds to reset the TV. 4 CHANNEL / —When no menu is onscreen, these buttons change the channel (programmed channels only, see “Storing channels in memory (optional)” on page 53).
Introduction TV back panel connections TV back panel connections For explanations of cable types and connections, see “Overview of cable types” on page 22. (Sample Illustration) 32L2200U/40L2200U - Back panel connections (Sample Illustration) 50L2200U Back panel connections 1 Digital AUDIO OUT—Optical audio output in Dolby® Digital or PCM (pulse-code modulation) format for connecting an external Dolby® Digital decoder, amplifier, or home theater system with optical audio input.
Introduction TV back panel connections 4 5 6 NOTE 21 ColorStream® HD—High-resolution component video input and shared composite video input. See “Connecting a Blu-ray™/DVD Player/Satellite receiver with ColorStream® (component video), or a VCR” on page 27. ANALOG AUDIO OUT—Analog audio outputs for connecting an audio amplifier. HDMI® IN—High-Definition Multimedia Interface input receives digital audio and uncompressed digital video from an HDMI® device or uncompressed digital video from a DVI device.
Chapter 2 Connecting Your TV Overview of cable types Before purchasing cables, know the connector types your devices require. You can purchase cables from most stores that sell audio/video devices. Coaxial (F-type) cable (Sample Illustration) Coaxial cable Coaxial (F-type) cable connects your antenna, cable TV service, and/or cable converter box to the ANT/CABLE input on your TV.
Connecting Your TV Overview of cable types 23 Standard A/V cables (composite video) usually come in sets of three, and connect to video devices with analog audio and composite video output. These cables (and the related inputs on your TV) are typically color-coded according to use: yellow for video, red for stereo right audio, and white for stereo left (or mono) audio.
Connecting Your TV Overview of cable types Optical audio cable (Sample Illustration) Optical audio cable Optical audio cable connects receivers with Dolby® Digital or PCM (pulse-code modulation) optical audio input to the TV’s Digital Audio Out terminal. See “Connecting a digital audio system” on page 33. Analog RGB (15-pin) computer cable (Sample Illustration) Analog RGB (15-pin) computer cable Analog RGB (15-pin) computer cable connects a computer to the TV’s PC IN terminal.
Connecting Your TV Connecting a VCR, antenna, cable TV, or camcorder Connecting a VCR, antenna, cable TV, or camcorder (Sample Illustration) 32L2200U/40L2200U Connecting to a VCR, antenna, cable TV, or camcorder Camcorder AUDIO OUT From cable TV or antenna From cable TV Cable box VIDEO L R IN CH 3 CH 4 TV back panel IN VIDEO/COLOR STREAM HD Y/VIDEO TV back panel OUT Stereo VCR VIDEO L AUDIO R IN CH 3 CH 4 OUT L R IN from ANT OUT to TV (Sample Illustration) 50L2200U - Connecting to a V
Connecting Your TV Connecting a VCR, antenna, cable TV, or camcorder NOTE When you use a cable box, you may not be able to use the remote control to program or access certain features on the TV. When you use ColorStream® HD or Video, switch to the appropriate AV input mode. To view the antenna or cable signal: Select ANT/CABLE video input source on the TV.* To view basic and premium cable channels: Turn Off the VCR. Select the ANT/CABLE video input source on the TV.
Connecting Your TV Connecting a Blu-ray™/DVD Player/Satellite receiver with Connecting a Blu-ray™/DVD Player/Satellite receiver with ColorStream® (component video), or a VCR TV back panel From antenna Stereo VCR PB Y/VIDEO VIDEO L AUDIO R IN From satellite dish CH 3 CH 4 PR OUT IN from ANT OUT to TV R L L/MONO AUDIO R AUDIO OUT Y Satellite IN L PR PB COMPONENT VIDEO S-VIDEO VIDEO OUT OUT R (Sample Illustration) 32L2200U/40L2200U Series - Connecting a Blu-ray™/DVD Player, Satelli
Connecting Your TV Connecting a Blu-ray™/DVD Player/Satellite receiver with ❖ NOTE Component video cables ❖ You can connect the component video cables (plus audio cables) from the DVD player or satellite receiver to the COLOR STREAM HD terminal in the TV. The COLOR STREAM HD terminal can be used to display Progressive (480p, 720p) and Interlaced (480i, 1080i) scan systems. Please note that 1080p is not supported.
Connecting Your TV ® Connecting an HDMI or DVI device to the HDMI® input 29 Connecting an HDMI® or DVI device to the HDMI® input The HDMI® input on your TV receives digital audio and uncompressed digital video from an HDMI® source device, or uncompressed digital video from a DVI (Digital Visual Interface) source device.
Connecting Your TV Connecting an HDMI® or DVI device to the HDMI® input TV back panel HDMI device (Sample Illustration) 32L2200U/40L2200U Series - Connecting an HDMI® or DVI device to the HDMI® input 2 1 TV side panel Playback device (Sample Illustration) 50L2200U Series - Connecting an HDMI® or DVI device to the HDMI® input To view the HDMI® device video: Select HDMI 1 or HDMI 2 video input source on the TV. (Press the INPUT button on the remote control.
Connecting Your TV ® Connecting an HDMI or DVI device to the HDMI® input PB 31 Y/VIDEO PR L/MONO AUDIO R VIDEO L DVI/HDCP OUT AUDIO R IN IN OUT R L (Sample Illustration) 32L2200U/40L2200U - DVI connections TV back panel 2 1 TV side panel VIDEO L DVI/HDCP OUT AUDIO R IN IN OUT L R (Sample Illustration) 50L2200U - DVI connections NOTE To ensure that the HDMI® or DVI device is reset properly: ❖ When turning on your electronic components, turn on the TV first, and then the HDMI® or DVI
Connecting Your TV HDMI® CEC connection HDMI® CEC connection You can control the basic functions of connected audio/video devices using the TV’s remote control if you connect a HDMI® CEC-compatible audio receiver or playback device. The HDMI® CEC Control feature uses CEC technology as regulated by the HDMI® standard.
Connecting Your TV Connecting a digital audio system NOTE 33 ❖ If several devices are connected, the HDMI® CEC Control feature may not operate properly. ❖ For proper operation, it is recommended that you use an HDMI® cable with the HDMI® Logo ( ). Before controlling the device(s): ❖ After completing the above connections, configure the HDMI® CEC Setup menu with the desired settings, see “HDMI® CEC input source selection” on page 113. ❖ The connected devices must also be configured.
Connecting Your TV Connecting a digital audio system (Sample Illustration) L2200U series - Connecting a digital audio system To control the audio: 1 Turn on the TV and the digital audio device. 2 Press the MENU button on the remote control and open the Sound menu. 3 Press the ( / arrow) buttons to highlight Audio Setup, and then press the ENTER button. (Sample Illustration) Sound menu - Audio Setup selection 4 Press the ( / Format.
Connecting Your TV Connecting an analog audio system 5 35 Press the ( / arrow) buttons to select either Dolby Digital or PCM, depending on your device. Digital Output Format Standard (Sample Illustration) Audio Setup screen - Done 6 To save the new settings, highlight Done, and then press the ENTER button. To revert to the factory defaults, highlight Reset, and then press the ENTER button. NOTE ❖ Some audio systems may not be compatible with Dolby® Digital bitstream signals.
Connecting Your TV Connecting a computer You will need standard audio cables. (Sample Illustration) 32L2200U/40L2200U- Connecting an analog audio system Audio system 2 1 ANALOG AUDIO OUT TV back panel (Sample Illustration) 50L2200U Series - Connecting an analog audio system Connecting a computer With either the PC IN or HDMI® connection, you can view your computer’s display on the TV and hear the sound from the TV’s speakers.
Connecting Your TV Connecting a computer 37 Connecting a computer to the TV’s PC IN terminal When connecting a computer to the PC IN terminal on the TV, use an analog RGB (15-pin) computer cable and a PC audio cable. For more information, see “Overview of cable types” on page 22.
Connecting Your TV Connecting a computer To display the optimum picture, use the computer setting feature, see “Using the PC Settings feature” on page 100. NOTE ❖ The PC audio input terminals on the TV are shared with the HDMI 1 analog audio input terminals. For configuration information, see “Setting the PC Audio” on page 101. ❖ Some computer models cannot be connected to this TV. ❖ If the computer has a compatible mini D-sub15-pin terminal, an adapter is not required.
Connecting Your TV Connecting a computer 39 TV back panel PB Y/VIDEO PR L/MONO AUDIO R PC audio cable Computer PC audio output HDMI® to DVI adapter cable (Sample Illustration) 32L2200U/40L2200U - Connections to HDMI® terminal TV side panel 2 1 TV back panel PC audio cable Computer PC audio output HDMI® to DVI adapter cable (Sample Illustration) 50L2200U - Connections to HDMI® terminal The supported signal formats are VGA, SVGA, XGA, WXGA, SXGA, 480i (60Hz), 480p (60Hz), 720p (60Hz), 1080
NOTE Connecting Your TV Connecting a computer ❖ The edges of the picture may be hidden. ❖ If receiving a 480i (HDMI®), 480p (HDMI®), 720p, 1080i, or 1080p signal program, Native mode scales the video to display the entire picture within the borders of the screen (i.e. no overscanning).
Chapter 3 Using the Remote Control Installing batteries To install batteries: 1 Remove the battery cover from the back of the remote control. Squeeze tab and lift cover (Sample Illustration) Removing the remote back cover 2 Insert two AAA batteries, corresponding to the (+) and (-) markings on the battery compartment. (Sample Illustration) Installing the batteries 3 Replace the battery cover. Do not expose batteries to excessive heat such as sunshine, fire, etc.
NOTE Using the Remote Control Installing batteries ❖ Be sure to use AAA size batteries. ❖ Dispose of batteries in a designated disposal area. ❖ Always consider the environment when disposing of batteries. Always follow applicable laws and regulations. ❖ If the remote does not operate correctly, or if the operating range is reduced, replace the batteries. ❖ Always replace both batteries with new ones. Never mix battery types or use new and used batteries together.
Using the Remote Control Remote control effective range 43 Remote control effective range For optimum performance, aim the remote control directly at the TV and make sure there is no obstruction between the remote control and the TV. 16.4 ft (5m) (Sample Illustration) 32L2200U/40L2200U Remote control effective range 16.
Using the Remote Control Learning about the remote control Learning about the remote control The buttons used for operating the TV are described below. For the HDMI® CEC remote control functions, see “HDMI® CEC playback device (DVD player, etc.) control” on page 111. (Sample Illustration) Remote control overview NOTE The error message “NOT AVAILABLE” may appear if you press a button for a function that is not available.
Using the Remote Control Learning about the remote control 45 1 The POWER button turns the TV On/Off. When the TV is on, the power LED indicator on the TV front glows green. 2 The PIC SIZE button cycles through the picture sizes. See “Selecting the picture size” on page 71. 3 The PIC MODE button selects the picture mode. See “Selecting the picture mode” on page 79. 4 The INPUT button selects the video input source. See “Selecting the video input source” on page 61.
Using the Remote Control Learning about the remote control 18 The Arrow buttons ( / / / ) select or adjust programming menus when a menu is on-screen. 19 The Arrow buttons ( / ) open the Channel Browser and tune to the previous/next channel in the channel history when TV programming is on-screen. See “Tuning channels using the Channel Browser” on page 65. 20 The MENU button accesses the main TV menu system.
Chapter 4 Menu Layout and Navigation Main menu layout The tables below and on the following pages provide a quick overview of your TV’s menu system. To open the Installation menus (illustrated below), press MENU on the remote control or TV control panel.
Icon Preferences Locks Setup Menu Layout and Navigation Main menu layout Item CC Selector Base CC Mode Digital CC Settings Input Labeling AV Input Menu Language Channel Browser Setup HDMI® CEC Player Control Energy Saving Settings Enable Rating Blocking Edit Rating Limits Input Lock Panel Lock GameTimer® New PIN Code Installation HDMI® CEC Setup Sleep Timer PC Settings Media Player Option Launches the temporary CC Selector Off/CC1/CC2/CC3/CC4/T1/T2/T3/T4 Opens the Digital CC Setup menu Opens the Inp
Menu Layout and Navigation Setup/Installation menu layout 49 Setup/Installation menu layout The Installation menu contains the Terrestrial and System Status menus. To open the Installation menu, press the MENU button on the remote control or TV control panel, open the Setup menu, select Installation, and then press the ENTER button.
Menu Layout and Navigation Navigating the menu system 4 All menus close automatically if you do not make a selection within approximately 60 seconds, except the signal meter menu, which closes automatically after a few minutes. 5 To close a menu instantly, press the EXIT button. NOTE The menu background may sometimes appear black, depending on the signal the TV is receiving. This is not a sign of malfunction.
Chapter 5 Setting up your TV Initial Setup When you first turn on or reset the TV, the Initial Setup window will appear. 1 In the Menu Language field, press the ( / select your preferred language. arrow) buttons to 2 Press the ( / arrow) buttons to select Time Zone Setup. Then set your desired time zone, using the ( / arrow) buttons and press the ENTER button. The Location settings window appears. 3 For normal home use, press the ( / arrow) buttons to select Home, and then press the ENTER button.
Setting up your TV Initial Setup Menu language You can choose from three different menu language settings (English, Français, and Español) for the on-screen display of menus and messages. To select the menu language: 1 Press the MENU button, open the Preferences menu, and then highlight Menu Language. 2 Press the ( / language. arrow) buttons to select your preferred (Sample Illustration) Selecting the menu language 3 Press the EXIT button to close the Preferences menu.
Setting up your TV Storing channels in memory (optional) 3 53 Open the Terrestrial menu, highlight Input Configuration, and then press the ENTER button. (Sample Illustration) Terrestrial menu - Input Configuration selection 4 Highlight ANT/CABLE In and press the ( / arrow) buttons to select the input source (Cable or Antenna). (Sample Illustration) Input Configuration screen 5 To save your new settings, highlight Done, and then press the ENTER button.
Setting up your TV Storing channels in memory (optional) NOTE ❖ You must set up the ANT/CABLE input source before programming channels. See “ANT/CABLE IN” on page 52. ❖ The automatic channel programming process will erase channels that were previously programmed into the TV’s memory. ❖ To tune the TV to a channel not programmed in the channel memory, you must use the Channel Number buttons on the remote control.
Setting up your TV Storing channels in memory (optional) 55 A new set of Installation menu icons appears. 4 Open the Terrestrial menu, highlight Channel Program to open the Start Scan window, and then press the ENTER button to begin channel programming. (Sample Illustration) Terrestrial menu - Channel Program selection (Sample Illustration) Auto tuning program channels The TV will automatically cycle through all the antenna channels, and store all active channels in the channel memory.
Setting up your TV Setting channel skip Setting channel skip To prevent a channel from being viewed, you can set it to be skipped. 1 From the Setup menu, highlight Installation, and then press the ENTER button. 2 Press the ( / arrow) buttons to select Channel Options, and then press the ENTER button. The list of channels appears. (Sample Illustration) List of channels 3 Press the ( / arrow) buttons to select a channel position to be skipped, and then press the ENTER button.
Setting up your TV Setting the AV input mode NOTE 57 Skipped channels cannot be selected with the CH arrow buttons, however, they can be accessed using the number keys on the remote control. If an encrypted channel is accidentally added to the channel list while programming channels, you can remove the unwanted encrypted (non-viewable) channel while you are channel surfing. To remove encrypted channels from the channel memory: ❖ Tune to an encrypted channel.
Setting up your TV Viewing the digital signal meter 3 Press the ( / arrow) buttons to select HDMI 1 Audio, and then press the ( / arrow) buttons to select the HDMI 1 audio mode (Auto, Digital, or Analog). (Auto is the recommended mode.) See “Connecting an HDMI® or DVI device to the HDMI® input” on page 29. (Sample Illustration) HDMI® Audio mode selection Mode: Description: Auto When viewing the HDMI 1 input, if digital audio from the HDMI® input is available, it will be output.
Setting up your TV Setting the time zone 59 To view the digital signal meter: 1 Press the MENU button and open the Setup menu. 2 Highlight Installation, and then press the ENTER button. A new set of Installation menu icons appears. 3 Open the Terrestrial menu, highlight Signal Meter, and then press the ENTER button. 4 Press the ( / / / arrow) buttons to select the antenna input and digital channel signal you wish to check.
Setting up your TV Viewing the system status Viewing the system status 1 Press the MENU button and open the Setup menu. 2 Highlight Installation, and then press the ENTER button. A new set of Installation menu icons appears. 3 Open the System Status menu, highlight System Information, and then press the ENTER button. 4 Press the ( / arrow) buttons to scroll through the menu bar to select Factory Defaults or Support Information. The related information appears.
Chapter 6 Using the TV’s features Selecting the video input source To select the video input source to view: 1 Press the INPUT button on the remote control or TV control panel. 2 Do one of the following: ❖ Press 0-4. ❖ Repeatedly press the ( / arrow) buttons on the remote control, and then press the ENTER button to change the input setting. ❖ Repeatedly press the INPUT button on the remote control or TV control panel to change the input setting.
Using the TV’s features Selecting the video input source The current signal source displays in the top right corner of the Input Selection screen. (Sample Illustration) Input Selection screen NOTE ❖ You can label the video input sources according to the specific devices you have connected to the TV. For instructions, see “Labeling the video input sources” on page 63. ❖ Sources can be “hidden.” For details, see “Labeling the video input sources” on page 63.
Using the TV’s features Labeling the video input sources NOTE 63 ❖ When you select HDMI® CEC input sources from the pop-up window using the INPUT button, some HDMI® CEC devices may automatically turn on. ❖ When selecting input sources using the ( / arrow) buttons, you will need to press the ENTER button to actually select a particular device from the pop-up window. Labeling the video input sources You can label each video input source according to the type of device you have connected to each source.
Using the TV’s features Labeling the video input sources 2 Highlight Input Labeling, and then press the ENTER button. AV Input ColorStream HD English HDMI-CEC Player Control (Sample Illustration) Preferences menu - Input Labeling selection 3 Press the ( / arrow) buttons to highlight the video source you wish to label. 4 Press the ( / arrow) buttons to select the desired label for that input source. If a particular input is not used, Hide can be selected as the label.
Using the TV’s features Tuning channels using the Channel Browser 65 Input labeling example: The screen below left shows the default Input Selection screen (with none of the inputs labeled as a specific device). The screen below right is an example of how you can label the inputs if you connected a VCR to ColorStream® HD, a video recorder to HDMI 1, and a DVD player to HDMI 2.
Using the TV’s features Tuning channels using the Channel Browser Favorites browser The Favorites Browser allows you to quickly set up a favorite channels/inputs list that is integrated into the Channel Browser. To add a favorite channel/input: 1 Tune to the channel or input. 2 Press and hold the FAV button for a few seconds. NOTE The channel or input is added to the beginning of the Favorites list on the left side of the Channel Browser.
Using the TV’s features Tuning channels using the Channel Browser 67 5 Press the ( arrow) button to highlight Inputs List, and then press the ( / arrow) buttons to select On or Off. 6 Press the ( arrow) button to highlight Favorites List, and then press the ( / arrow) buttons to select On or Off. 7 Press the ( arrow) button to highlight HDMI® CEC List, and then press the ( / arrow) buttons to select On or Off.
Using the TV’s features Tuning channels using the Channel Browser 3 Channel or input currently being viewed. 4 Channel or input that is currently highlighted in the browser. 5 Channels stored in the History List. To toggle among the available lists: After opening the Channel Browser, press the ( / arrow) buttons to toggle through the History, ANT/CABLE, Inputs, Favorites, or HDMI® CEC options. NOTE ❖ The Channel Browser opens in History List by default.
Using the TV’s features Tuning channels using the Channel Browser 69 Adding and clearing channels and inputs in the History List As a channel or input is tuned, the Channel Browser adds it to the History List and displays it on the right side of the Channel Browser. Previously tuned channels/inputs are shifted to the left, eventually moving off the left side. Press the BACK CB arrow button to surf backward through the previously tuned channels/inputs.
Using the TV’s features Tuning channels using the Channel Browser Tuning to a specific channel (programmed or unprogrammed) To tune analog channels: Press the Channel Number (0–9) on the remote control. For example, to select channel 125, press 1, 2, 5, and then press the ENTER button. Tuning digital channels: Press the Channel Number (0–9) on the remote control, followed by the (Dash 100) button, and then the sub-channel number.
Using the TV’s features Selecting the picture size 71 2 Press and hold the CH RTN button for a few seconds until the message “Memorized” appears on the screen. The channel has been programmed to the CH RTN button. 3 You can then change channels repeatedly, and when you press the CH RTN button, the memorized channel will be tuned. The TV will return to the memorized channel one time only.
Using the TV’s features Selecting the picture size To select the picture size using the menus: 1 Select Picture Size in the Theater Settings menu. 2 Press the ( / setting. 3 Highlight Done, and then press the ENTER button. arrow) buttons to select the desired picture size NOTE Some of the picture sizes may not be available depending on the receiving signal format (those will be grayed out in the Picture Size screen).
Using the TV’s features Selecting the picture size 73 The Full setting is for viewing in 1080i, 1080p, and 720p program source. (Sample Illustration) Picture size - Full The edges of the picture may be hidden. TheaterWide 1 This setting is for viewing in 4:3 format programs. (Sample Illustration) Picture size - TheaterWide 1 The center of the picture remains close to its original proportion, but the left and right edges are stretched horizontally to fill the screen.
Using the TV’s features Selecting the picture size TheaterWide 3 This setting is for viewing letter box programs with subtitles. (Sample Illustration) Picture size - TheaterWide 3, letter box with subtitles The picture’s top and bottom edges are hidden*. * To view the hidden areas (such as subtitles or captions), see “Scrolling the TheaterWide® picture (TheaterWide 2 and 3 only)” on page 76. Native These settings are for viewing in 480i (HDMI®), 480p (HDMI®), 720p, 1080i, and 1080p signal programs.
Using the TV’s features Selecting the picture size 75 4:3 (Sample Illustration) Picture size - 4:3 Some program formats will display with sidebars and/or bars at the top and bottom. Normal This setting is for viewing VGA, SVGA, XGA, WXGA, and SXGA sources. (Sample Illustration) Picture size - Normal This size is a non-stretched display. Some input signal formats will display with sidebars and/or bars at the top and bottom. Dot by Dot This setting is for viewing VGA, SVGA, XGA, WXGA, and SXGA sources.
Using the TV’s features Scrolling the TheaterWide® picture (TheaterWide 2 and 3 only) Scrolling the TheaterWide® picture (TheaterWide 2 and 3 only) You can set separate scroll settings for the TheaterWide 2 and TheaterWide 3 modes for each input. To set the scroll settings: 1 Press the MENU button and open the Picture menu. 2 Highlight Theater Settings, and then press the ENTER button.
Using the TV’s features Using the Auto Aspect feature 77 Using the Auto Aspect feature When this feature is set to On, the TV will automatically select the picture size when one of the following input sources is received: ❖ A 480i, 480p, 720p, 1080i digital signal from the ANT/CABLE input ❖ A 480i signal from the ColorStream® HD or Video input ❖ 480i, 480p, 720p, 1080i, 1080p, or VGA (60Hz) signal from the HDMI 1 or HDMI 2 input.
Using the TV’s features Selecting the Cinema Mode Selecting the Cinema Mode When you view a DVD (3:2 pulldown processed) from a DVD player connected to the VIDEO, ColorStream® HD (component video), or HDMI® inputs on the TV, smoother motion can be obtained by setting the Cinema Mode to Film. To set the Cinema Mode to Film: (available for 480i and 1080i signals) 1 Press the MENU button and open the Picture menu. 2 Highlight Picture Settings, and then press the ENTER button.
Using the TV’s features Adjusting the picture 79 Adjusting the picture Selecting the picture mode You can select your desired picture settings from the modes described below.
Using the TV’s features Adjusting the picture 3 Press the ( / arrow) buttons to select the picture mode you prefer, and then press the ENTER button. (Sample Illustration) Mode selections screen Adjusting the picture quality You can adjust the picture quality (Contrast, Backlight, DynaLight™, Brightness, Color, Tint, and Sharpness) to your personal preferences.
Using the TV’s features Using closed captions 81 3 Press the ( / arrow) buttons to select the picture quality you wish to adjust (Contrast, Backlight, DynaLight, Brightness, Color, Tint, or Sharpness), and then press the ( / arrow) buttons to adjust the setting. 4 To save the new settings, highlight Done, and then press the ENTER button. You can use any of the picture modes (see “Selecting the picture mode” on page 79) as a starting point for adjusting the picture settings.
Using the TV’s features Using closed captions NOTE If the program or video you selected is not closed captioned, no captions will display onscreen. To view text, highlight T1, T2, T3, or T4. (Sample Illustration) Captions - text NOTE If text is not available in your area, a black rectangle may appear on screen. If this happens, set the Base CC Mode to Off. To turn off closed caption mode, select Off in step 2 above.
Using the TV’s features Using closed captions 83 3 Press the ( / arrow) buttons to highlight the characteristic you wish to change, and then press the ( / arrow) buttons to select the format for that characteristic. 4 To save the new settings, highlight Done, and then press the ENTER button. To revert to the factory defaults, highlight Reset, and then press the ENTER button. Mode: Description Caption size Auto, Small, Standard, Large Caption text type Auto, Default, Mono (with Serif), Prop.
Using the TV’s features Adjusting the audio 4 Press the EXIT button. Adjusting the audio Muting the sound Press the MUTE button to partially reduce (1/2 Mute) or turn off (Mute) the sound. Each time you press the MUTE button, the mute mode changes in the following order: 1/2 Mute, Mute, Volume, 1/2 Mute, etc. (Sample Illustration) Levels of mute If closed caption mode is set to Off when you select MUTE mode, the closed caption feature becomes active if the TV program is closed captioned.
Using the TV’s features Adjusting the audio 2 85 Highlight Digital Audio Selector, and then press the ENTER button. (Sample Illustration) Sound menu - Digital Audio Selector selection 3 Press the ( / arrow) buttons to select Digital Audio, and then press the ( / arrow) buttons to select the desired service. 4 Press the EXIT button. Selecting stereo/SAP broadcasts The multi-channel TV sound (MTS) feature allows you to output high-fidelity stereo sound.
Using the TV’s features Adjusting the audio To listen to an alternate language on an ATSC digital station (if available), highlight the Language field in step 3 above, and then press the ( / arrow) buttons to select the language you prefer. To listen to a second audio program on an analog station, if available, select SAP in step 3 above. NOTE ❖ A second audio program (SAP) can be heard only on those TV stations that offer it.
Using the TV’s features Adjusting the audio 87 Audyssey Premium Television™ (50L2200U only) These televisions use a suite of technologies for better sound quality, including the following: ❖ Audyssey EQ®—provides clear, accurate and natural sound right out of the box. This technology ensures you enjoy your audio experience as much as your video. ❖ Audyssey ABX™—technology uses sophisticated driver analysis and low frequency monitoring to extend the range and bass of small speakers.
Using the TV’s features Adjusting the audio When you use ColorStream® HD or Video, switch the AV input mode as appropriate. NOTE 32L2200U and 40L2200U models do not support Audyssey Dynamic Volume®. Stable Sound (32L2200U/40L2200U only) The Stable Sound feature limits high volume levels and prevents the extreme changes in volume that can occur when channels are changed or a program switches to a commercial. To turn on Stable Sound: 1 Press the MENU button and open the Sound menu.
Using the TV’s features Using the Locks menu 89 Using the Dolby® Digital Dynamic Range Control feature You can further compress Dolby® Digital dynamic range, allowing you to switch from digital to analog broadcasts at the same dynamic range. To use the Dolby® Digital Dynamic Range Control: 1 Press the MENU button, and then open the Sound menu. 2 Highlight Audio Setup, and then press the ENTER button. 3 In the Dolby Digital Dynamic Range Control field, select either Compressed or Standard.
Using the TV’s features Using the Locks menu 2 Press the ( screen. arrow) button to display the PIN code entry The Lock System screen appears if a PIN code has not been stored. (Sample Illustration) Lock system - store PIN screen ❖ Press the Channel Number buttons to enter a new fourdigit code, enter the code a second time to confirm, and then press the ENTER button. The Locks/Active screen appears if the PIN code is already stored.
Using the TV’s features Using parental controls (for USA region) 91 3 Enter your four-digit PIN code, and then press the ENTER button. 4 Press the ( arrow) button to highlight New PIN Code, and then press the ENTER button. 5 Press the Number buttons to enter a new four-digit code. Reenter the PIN code to confirm it. 6 Press the ENTER button. The new PIN code is now active. NOTE The PIN code cannot be set to “0000.
Using the TV’s features Using parental controls (for USA region) 6 Press the ( arrow) button to highlight Edit Rating Limits, and then press the ENTER button. The Edit Rating Limits screen appears. 7 For each desired selection, press the ( / / / arrow) buttons to highlight the selection, and then press the ENTER button to select it. A box with an “X” is a rating that will be blocked. As you highlight a rating, a definition for the rating appears at the bottom of the screen.
Using the TV’s features Using parental controls (for USA region) NOTE 93 ❖ The Alt RS button will be available only if an additional rating system is currently available. ❖ It may take several minutes for the TV to download the additional rating system. ❖ The information displayed in the Alternate Ratings screen will depend on the configuration of the additional rating system available at the time of download.
Using the TV’s features Ratings: TV-14 Description and Content themes: Parents Strongly Cautioned (This program contains some material that many parents would find unsuitable for children under 14 years of age.) D) Intensely suggestive dialogue L) Strong, coarse language S) Intense sexual situations V) Intense violence Parental Guidance Suggested (This program contains material that parents may find unsuitable for younger children.
Using the TV’s features Using parental controls (for USA region) 95 Displaying ratings To display the rating of the program you are watching, press the INFO button on the remote control. If it is rated “None,” then the word “NONE” appears in the INFO screen. If rating information is not provided, no rating will appear in the INFO screen. (Sample Illustration) Rating Info screens Blocking TV programs by Canadian rating 1 Press the MENU button, and then highlight the Locks menu icon.
Using the TV’s features Using parental controls (for USA region) Rating system for programs in English: Ratings: E C C8+ G PG 14+ Description and Content themes: Exempt shows Children, ages 2 to 7 years Children, ages 8 years and older General programming Parental Guidance Viewers 14 and older Adult programming 18+ Rating system for programs in French: Ratings: E G 8 ans+ 13 ans+ 16 ans+ 18 ans+ Description and Content themes: Exempt shows General programming Not recommended for ages under 8 Not r
Using the TV’s features Using the Input Lock feature 97 Using the Input Lock feature You can use the Input Lock feature to lock the video inputs (Video, ColorStream® HD, HDMI 1, HDMI 2, and PC) and channels 3 and 4. You will not be able to view the input sources or channels until you unlock the inputs. To lock/unlock the video inputs: 1 From the Locks menu, press the ( the PIN code entry screen. 2 Enter your four-digit PIN code, and then press the ENTER button.
Using the TV’s features Locking channels 3 Press the ( / arrow) buttons to select Channel Options, and then press the ENTER button. The list of channels appears. (Sample Illustration) Channel options 4 Press the ( arrow) button, and then press the ( / buttons to select a channel in the lock column. 5 Press the ENTER button. arrow) PIN code entry will be required to set a locked channel. NOTE If the PIN code has not yet been set, a warning message appears. 6 A check appears in the box.
Using the TV’s features Locking channels 99 To cancel the GameTimer®, select Off in step 3 above. To deactivate the Input Lock after the GameTimer® has activated it: ❖ NOTE Set the Input Lock to Off. For instructions, see “Using the Input Lock feature” on page 97. ❖ Messages appear when 10 minutes, 3 minutes, and 1 minute are remaining. ❖ If the TV loses power with time remaining, the TV will enter Input Lock mode when power is restored (as if the GameTimer had been activated).
Using the TV’s features Using the PC Settings feature To unlock the control panel, select Off in step 5 in this section or press and hold the VOLUME (–) button on the TV control panel for approximately 15 seconds until the volume icon appears. Using the PC Settings feature You can view an image from a PC on the TV screen. When a PC is connected to the TV's PC IN terminal, you can use the PC Settings feature to make adjustments to the image.
Using the TV’s features Using the PC Settings feature 5 Press the ( / adjustments. 101 arrow) buttons to make the appropriate (Sample Illustration) PC Settings - adjustments screen NOTE The screen is disrupted momentarily while adjusting the PC settings. This is not a sign of malfunction. Mode: Description: Horizontal Position Moves the picture left/right. The adjustment range is within ±10 from center.* Vertical Position Moves the picture up/down. The adjustment range is within ±10 from center.
Using the TV’s features Using the Media Player ❖ NOTE No: When viewing the PC input, there will be no audio. Because the PC and HDMI 1 inputs share the same set of analog audio inputs, the PC Audio menu setting influences the HDMI 1 Audio menu setting. If PC Audio is set to “No,” then the HDMI 1 Audio setting changes to “Auto.” If PC Audio is set to “Yes,” then the HDMI 1 Audio setting is set to “Digital” and is grayed out in the menu. (See also “Setting the HDMI® audio mode” on page 57.
Using the TV’s features Using the Media Player NOTE 103 ❖ Gently insert the USB device into the port and do not remove while viewing Media Player. ❖ USB device: USB Mass Storage Class device (MSC). ❖ Connectivity is not guaranteed for all devices. ❖ Connect the USB device to the TV directly. ❖ Do not use a USB Hub. ❖ You must obtain any required permission from copyright owners to use copyright content. Toshiba cannot and does not grant such permission.
Using the TV’s features Using the Media Player NOTE 2 If you repeatedly insert and remove the USB connector, the prompt may not appear. Press the ( / arrow) buttons to select Yes, and then press the ENTER button. The Media Player menu appears. (If you select No, nothing happens.) (Sample Illustration) Media Player - open screen NOTE ❖ The prompt will disappear after about 10 seconds. ❖ If Auto Start is set to off, you can start the Media Player manually.
Using the TV’s features Using the Media Player 105 Viewing photo files There are three types of view modes: multi view, single view, and slide show. Multi View This view allows you to search for photos in a grid format. These pictures are displayed using thumbnail data in each image file. (Sample Illustration) Media Player - photos screen To use multi view: 1 Press the ( / / / arrow) buttons to move the highlight in one window.
Using the TV’s features Using the Media Player ❖ Press to rotate the image 90° counterclockwise. Press rotate the image 90° clockwise. to Slide show This view allows you to watch a slide show of the photos. In this mode, only files located in the selected directory will be played. To use slide show: 1 Press the ENTER button in the Single View mode. 2 Press the ( / photo.
Using the TV’s features Using the Media Player 107 2 Select the desired folder and press the ENTER button to move to the next layer. Press the CH RTN button to move back to the previous layer. 3 With the desired file selected, press the ENTER button or the PLAY button to start playback. 4 Press the STOP button to stop playback. NOTE ❖ If playback finishes before STOP is pressed, the next file will automatically start to play from the beginning.
Using the TV’s features Using the Media Player 3 Select a music file and press the ENTER button to start playback. 4 Press CH RETURN twice to move back to photo view mode. The music is now playing in the background. Sorting photo or music files From the photos Multi View or from the music list, you can sort your photo or music folders and files. To sort photo or music folders and files: 1 From photo Multi View mode or from the music list, press the MENU button to open the Quick Menu.
Using the TV’s features Setting the sleep timer Contents Music Description Music list (Multi View) Playback Pause Stop Skip Repeat play Sound Settings (Adjusting the audio quality) Description See page 106 NOTE During playback, you can adjust the SOUND menu functions from the Quick Menu. NOTE Sorting, Total Time display may not be available in all cases. Setting the sleep timer You can set the sleep timer to turn off the TV after a set length of time (maximum of 12 hours).
Using the TV’s features Automatic Power Down To display the time remaining until the TV turns off, press the SLEEP button. To cancel the sleep timer, repeatedly press SLEEP until it is set to 0 minutes. Automatic Power Down The TV can be configured to automatically turn itself off after 4 hours if you do not operate the TV either from the remote control or the TV control panel. 1 From the Preferences menu, highlight Energy Saving Settings and press ENTER. 2 Press the ( / Down.
Using the TV’s features Using HDMI® CEC 3 NOTE 111 Press the ( / arrow) buttons to highlight the item you want to change, and then press the ( / arrow) buttons to select On or Off. ❖ Default setting for this feature is On. ❖ A warning message will appear 1 minute before the TV turns off. Using HDMI® CEC This is a new feature that uses CEC technology and allows you to control Toshiba HDMI® CEC compatible devices from the TV remote via HDMI® connection (see “HDMI® CEC connection” on page 32).
Using the TV’s features Using HDMI® CEC HDMI® CEC Player Control menu functions To control the HDMI® CEC player from the menu: 1 Press MENU and open the Preferences menu. 2 Highlight HDMI® CEC Player Control, and then press the ENTER button. (Sample Illustration) Preferences menu - HDMI® CEC Player Control 3 Item: Power Root Menu Contents Menu Setup Menu Top Menu Menu NOTE Press the ( / arrow) buttons to select the item you wish to control, and then press the ENTER button.
Using the TV’s features Using HDMI® CEC 113 HDMI® CEC input source selection If an HDMI® CEC device with HDMI® switching capability (such as an Audio Receiver) is connected to the HDMI® input, you can select another HDMI® CEC device that is connected to the master HDMI® device using the TV’s INPUT button. For instructions, see “Selecting the video input source” on page 61.
Using the TV’s features Displaying TV status information NOTE When you turn on the Audio Receiver, change its input source, or adjust the sound volume, the sound will be output from the audio receiver’s speakers even if TV Speakers have been selected. Turn the TV off and on again to output the sound from the TV speakers. Setting up HDMI® CEC To set the HDMI® CEC Setup: 1 From the Setup menu, highlight HDMI® CEC Setup and press the ENTER button.
Using the TV’s features Understanding the Last Mode Memory feature 115 ❖ Digital signal strength indicator (bar graph in lower right corner of box; for ATSC signals only) ❖ Stereo, Mono, or SAP audio status (when in HDMI® input mode, Dolby® Digital, or PCM) ❖ Video resolution ❖ Aspect ratio of incoming video signal (4:3 or 16:9) ❖ V-Chip rating status ❖ GameTimer (if set) To close the Recall screen, press the RECALL button again.
Chapter 7 Using the TV’s Advanced Features Using the advanced picture settings Dynamic Contrast Dynamic Contrast detects changes in picture quality that affect the appearance of your contrast settings, and then automatically adjusts the video. To select Dynamic Contrast preference: 1 From the Picture menu, highlight Picture Settings, and then press the ENTER button. (Sample Illustration) Dynamic Contrast screen 116 2 Highlight Advanced Picture Settings, and then press the ENTER button.
Using the TV’s Advanced Features Using the advanced picture settings 4 Press the ( / Off. 117 arrow) buttons to select High, Middle, Low, or Static Gamma The static gamma feature lets you adjust the levels of black in the picture. To adjust the static gamma settings: 1 Press the MENU button, and open the Picture menu. 2 Highlight Picture Settings, and then press the ENTER button. 3 Highlight Advanced Picture Settings, and then press the ENTER button.
Using the TV’s Advanced Features Using the advanced picture settings To select the color temperature: 1 Press the MENU button and open the Picture menu. 2 Highlight Picture Settings, and then press the ENTER button. 3 Highlight Advanced Picture Settings, and then press the ENTER button. 4 Highlight Color Temperature, and then press the ENTER button. Use the ( / arrow) buttons to select the mode you prefer (Cool, Medium, or Warm).
Using the TV’s Advanced Features Using the advanced picture settings 3 119 In the CableClear field, select the desired setting. The available selections are Off, Low, Middle, and High. Low, Middle, and High will reduce the noise in varying degrees, from lowest to highest, respectively. NOTE 4 If the current input is ANT/CABLE or VIDEO, then the menu will display the text “CableClear.” If the current input is ColorStream® HD, HDMI 1, or HDMI 2, then the menu will display the text “DNR”.
Using the TV’s Advanced Features Using the advanced picture settings NOTE To use the Game Mode feature, the current video input must be Video, ColorStream® HD, HDMI 1, or HDMI 2. The Game Mode cannot be turned on when any other video input (other than the above-mentioned) is selected. To turn on Game Mode: 1 Press the MENU button, and then open the Picture menu. 2 Select GAME MODE, and then press the ( / buttons to select On.
Chapter 8 Troubleshooting General troubleshooting Before calling a service technician, review this chapter or visit the Toshiba technical support Web site at support.toshiba.com for possible causes and solutions for the problem you are experiencing. Before you begin to troubleshoot any problem, first unplug the TV from the AC wall outlet, wait approximately one minute, and then plug the TV back into the AC wall outlet. If the problem still exists, then you should attempt to troubleshoot the problem.
Troubleshooting Picture problems Other problems. If your TV’s problem is not addressed in this Troubleshooting section or the recommended solution has not worked, then use the Reset Factory Defaults procedure. For instructions, see “Resetting Factory Defaults” on page 60. TV will not turn on. Ensure the power cord is plugged in properly, and then press the POWER button. Replace the batteries in the remote control. For instructions, see “Installing batteries” on page 41.
Troubleshooting Sound problems 123 Video Input Selection problems. If the Input Selection window does not appear when you press INPUT on the remote control or TV, try pressing INPUT a second time. This will cause a change to the next video input source and will display the Input Selection window. Poor display color or no color. The station may be having broadcast difficulties. Try another channel. To adjust the Tint and/or Color, see “Adjusting the picture quality” on page 80. Poor composite picture.
Troubleshooting Remote control problems If you hear no sound, try setting the MTS feature to Stereo mode. See “Selecting stereo/SAP broadcasts” on page 85. If you are not receiving a second audio program from a known SAP source, make sure the MTS feature is set to SAP mode. See “Selecting stereo/SAP broadcasts” on page 85. If you hear audio that seems incorrect for the program you are watching (such as music or a foreign language), then the SAP mode may be on. Set the MTS feature to Stereo mode.
Troubleshooting Closed caption problems 125 If the problem persists, use the Reset Factory Defaults procedure. For instructions, see “Resetting Factory Defaults” on page 60. Closed caption problems If the program or video you have selected is not closed captioned, no captions appear on the screen. If text is not available, a black rectangle may appear. If this happens, turn off the closed caption feature. For instructions, see “Using closed captions” on page 81.
Troubleshooting HDMI® problems HDMI® problems HDMI® cables. Ensure that HDMI® cables with the ( ) logo are used. For more information, see “Connecting an HDMI® or DVI device to the HDMI® input” on page 29. Legacy HDMI® sources. Some legacy HDMI® sources may not work properly with the latest HDMI® TV products due to new standard adoption. Media Player problems Incorrect functionality may occur when using a USB HUB connection.
Appendix A Specifications NOTE ❖ These models comply with the specifications listed below. ❖ Designs and specifications are subject to change without notice. ❖ These models may not be compatible with features and/or specifications that may be added in the future.
Specifications Power source Power source 120V AC, 60 Hz Power maximum current 32L2200U 40L2200U 50L2200U 0.9A 1.5A 1.2A Power consumption 32L2200U 40L2200U 50L2200U 0.25W in standby mode 0.25W in standby mode 0.2W in standby mode Audio power 32L2200U 40L2200U 50L2200U 6 6 6 7W + 6 7W + 6 7W + 6 7W 7W 7W Speaker type 32L2200U 40L2200U 50L2200U Two 5.57" x 1.26" x 0.78" Two 5.98" x 1.57" x 1.42" Two 5.98" x 1.57" x 1.
Specifications Dimensions (with stand) ColorStream® (component video) HD input Video Y: 1V(p-p), 75 ohm PR: 0.7 V(p-p), 75 ohm PB: 0.7 V(p-p), 75 ohm Suggested formats: 1080i, 720p, 480p, 480i 200 mV(rms) (-20dBFS, 47K ohm or greater) Audio HDMI® input HDMI® compliant (type A connector) HDCP compliant 2-channel Linear-PCM; 32/44.
Specifications Supplied accessories Operating conditions Temperature Humidity 32 - 95º F (0 - 35º C) 20 - 80% (no moisture condensation) Supplied accessories ❖ Remote control with two size “AAA” batteries ❖ Warranty ❖ Resource Guide ❖ Quick Start Guide ❖ Pedestal and hardware Acceptable signal formats for PC IN, HDMI® PC IN signal formats NOTE Depending on the connected PC, the following conditions may occur: incorrect display, false format detection, picture position failure, blur, or j
Specifications Acceptable signal formats for PC IN, HDMI® 131 Format Resolution V. Frequency H. Frequency Pixel Clock Frequency XGA 1024 x 768 60.004 Hz 48.363 kHz 65.000 MHz 1280 x 768 59.870 Hz 47.776 kHz 79.500 MHz 1360 x 768 60.015 Hz 47.712 kHz 85.500 MHz SXGA 1280 x 1024 60.020 Hz 63.981 kHz 108.000 MHz 480i 720 x 480i 59.940 Hz 15.734 kHz 27.000 MHz 480p 720 x 480p 59.940 Hz 31.469 kHz 27.000 MHz 720p 1280 x 720p 60.000 Hz 45.000 kHz 74.
Appendix B License Agreement License Information on the software used in the TOSHIBA Digital TV The software pre-installed in the TOSHIBA Digital Televisions consists of multiple, independent software components. Each software component is copyrighted by TOSHIBA or a third party. The TOSHIBA Digital Televisions uses software components that are distributed as freeware under a third-party end-user license agreement or copyright notice (hereinafter referred to as a “EULA”).
License Agreement 133 implied. “Warranty” here includes, but not limited to, an implied warranty for marketability or fitness for specific uses. All risks associated with the quality or performance of these software components are assumed by the user. TOSHIBA shall not be liable whatsoever for any cost of repair or correction or other incidental expense incurred in connection with a defect found in any of these software components.
License Agreement (3) Permission for use of this software is granted only if the user accepts full responsibility for any undesirable consequences; the authors accept NO LIABILITY for damages of any kind. These conditions apply to any software derived from or based on the IJG code, not just to the unmodified library. If you use our work, you ought to acknowledge us.
License Agreement 135 This license was inspired by the BSD, Artistic, and IJG (Independent JPEG Group) licenses, which all encourage inclusion and use of free software in commercial and freeware products alike. As a consequence, its main points are that: ❖ We don't promise that this software works. However, we will be interested in any kind of bug reports. (“as is” distribution) ❖ You can use this software for whatever you want, in parts or full form, without having to pay us.
Index A advanced picture settings CableClear® digital Noise Reduction 118 Color temperature 117 Dynamic Contrast 116 MPEG Noise Reduction 119 Static Gamma 117 using 116 audio adjusting quality 86 Audyssey ABX™ 87 Dolby® Digital Dynamic Range Control 89 muting sound 84 optical audio output format 88 stereo/SAP broadcasts 85 Audyssey Dynamic Volume® using 87 Auto Aspect using 77 auto power down set 110 136 Auto Start function Media Player 103 AV input mode setting 57 B blocking programs Canada rating 95 C
Index Channel Browser elements 67 tuning channels 65 Channel Return switching between two channels 70 channels auto tuning 53 locking channels 97 skipping 56 specific channel 70 storing in memory 53 cinema mode selecting 78 closed captions CC selector 83 Digital CC settings 82 using 81 computer setting the audio 101 using with the TV 100 connecting a computer 36 audio system 33 cable TV 25 computer to TV’s PC IN 36 DVD player with ColorStream® 27 DVI device to HDMI® input 29 HDMI® device to HDMI® input 29
Index using 102 menu layout 49 navigation 49 setup 49 N no signal power down set 110 O pin code changing 90 deleting 90 entering PIN code 89 forgotten 90 program ratings displaying 95 unlocking programs 96 Q overview installation 17 setup 17 use 17 quick setup ANT/CABLE IN 52 menu language 52 P rating system 93 downloading additional 92 panel lock feature using 99 parental controls blocking programs/movies by rating (V-Chip) 91 using 91 PC Audio setting 101 PC settings feature using 100 pictu
Index SurfLock™ switching between two channels 70 system status viewing 60 T time zone setting 59 timer sleep timer 109 troubleshooting 121 channel tuning problems 124 closed caption problems 125 contact Toshiba 126 HDMI® 126 media player problems 126 No HDMI® CEC operation 125 picture problems 122 Rating blocking problems 125 remote control problems 124 sound problems 123 TV connections front 18 side 18 TV panel connections back 20 TV panel controls front 18 left side 18 side 18 TV remote functionality 4