USB Flash Memory U2M Security Software Installation Manual USB Flash Memory TransMemory™ U2M-016GT U2M-008GT U2M-004GT Security Software Installation Manual For U2M series 1
USB Flash Memory U2M Security Software Installation Manual Table of Contents Chapter 1: Introduction....................................................................................... 3 Chapter 2: Required System Configuration ........................................................ 5 Chapter 3: How to Install the Security Software ................................................. 6 1. Installing the security software ....................................................................... 6 1.
USB Flash Memory U2M Security Software Installation Manual Chapter 1: Introduction Thank you for purchasing TransMemory™ USB flash memory. It has the following features. ・It is USB flash memory employing Toshiba’s NAND flash memory. It can be used as a removable disk for a personal computer. ・It employs security software, allowing data that has been saved in the memory to be password-protected. ・Since it is bus-powered, an AC power adapter is not required.
USB Flash Memory U2M Security Software Installation Manual * If you are using the Windows Vista® operating system, do not enable ReadyBoost™ to use the Privacy Zone. This document describes how to install TransMemory™, how to use it, and other information. Before using the product, be sure to read it thoroughly to ensure correct use. * The images depicted in this manual may differ from the actual product.
USB Flash Memory U2M Security Software Installation Manual Chapter 2: Required System Configuration The following are required to properly operate this product: - Required hardware CPU: Intel Pentium II 266MHz or higher Available hard disk space of at least 800 KB USB Specification-compliant USB port (Operation on self-built or modified PCs cannot be guaranteed.
USB Flash Memory U2M Security Software Installation Manual Chapter 3: How to Install the Security Software This chapter describes how to install the security software to use this product. Be sure to install it correctly in accordance with the following explanation. 1. Installing the security software Be sure to install the security software when TransMemory™ is connected to the computer. Close all other applications. 1.1 Installing the security software 1) Start up the computer.
USB Flash Memory U2M Security Software Installation Manual 5) A dialog box asking where the software is to be saved appears. Select on “Desktop”. 6) When the download is complete, the following dialog box appears. Click “Close”.
USB Flash Memory U2M Security Software Installation Manual 7) On the desktop, the downloaded software named “U2LM_SecuritSoft_305.zip” appears as a new executable file. Double click on the icon. 8) It right-clicks in the icon of the security software installation program. When the following dialog box appears, and click “Extract All…”.
USB Flash Memory U2M Security Software Installation Manual 9) The following dialog box appears. Click “Next”. 10) The following dialog box appears. Click “Next”.
USB Flash Memory U2M Security Software Installation Manual If the “Destination folder” is not the “Desktop”, click “Browse…”. The following dialog box appears, so select “Desktop” as the destination folder. 11) The following dialog box appears. Click “Finish”.
USB Flash Memory U2M Security Software Installation Manual 12) The following folder appears. 10) Opening the folder displays the following. That completes the installation. Once it is installed, it can be used in the future by double clicking on the “TransMemory_Secure305.exe” icon in the “U2LM_SecuritySoft_305” folder. * After completing installation, the executable file, “U2LM_SecuritySoft_305.zip” may be deleted.
USB Flash Memory U2M Security Software Installation Manual Chapter 4: How to Use the Security Software This chapter describes how to use the security software for using TransMemory™. Be sure to follow the instructions for correct installation. The software shows additional dialogue when you use some type of TransMemory™. In this case follow the instruction below. Connect TransMemory™ to PC and double click the Security Software icon “TransMemory_Secure305.exe”.
USB Flash Memory U2M Security Software Installation Manual Click “OK” on the dialogue box below. Click “OK” on the dialogue box below. Disconnect the TransMemory™ from the PC. These dialogues will not appear once you finished this protocol.
USB Flash Memory U2M Security Software Installation Manual 1. Starting up and formatting the security software Be sure to start up and format the security software when TransMemory™ is connected to the personal computer. 1.1 Starting up the security software 1) Double click on the “TransMemory_Secure305.exe” security software icon to start up the security software. 2) When the following dialog box appears, click on “OK”.
USB Flash Memory U2M Security Software Installation Manual 3) When the following dialog box appears, confirm and click on “OK” when there is no privacy zone. The dialog of 7) on page 12 appears when there is already a privacy zone. The following dialog box appears.
USB Flash Memory U2M Security Software Installation Manual 4) Slide the partition to determine the size of the Privacy Zone. Enter the “Password”, reenter the “Confirm Password”, then a “Hint”, and click on “OK”. Note: If you forget the password, you will not be able to log into the Privacy Zone. A forgotten password cannot be found. In that case, use the formatting function of the security software and set a new password in Reformat. Note, however, that all data will be lost.
USB Flash Memory U2M Security Software Installation Manual The following dialog box appears, then automatically disappears. 6) When the following dialog box appears, confirm and click on “OK”. 7) The following dialog box appears. The start is completed.
USB Flash Memory U2M Security Software Installation Manual 1.2 Formatting using the security software 1) When the following dialog box appears, click on “Settings”. 2) When the following dialog box appears, click on “Format”.
USB Flash Memory U2M Security Software Installation Manual 3) When the following dialog box appears, slide the partition to determine the size of the Privacy Zone. Enter the “Password”, re-enter the “Confirm Password”, then a “Hint”. Note that the size of the Privacy Zone is limited to a maximum of 90% of the available memory (user area). The faint pink area is the Privacy Zone.
USB Flash Memory U2M Security Software Installation Manual 4) Determine the size of the Privacy Zone. Enter the “Password”, re-enter the “Confirm Password”, then a “Hint”, and click on “OK”. Note: The “Password” is a maximum of 16 characters using half-width alphanumeric (case sensitive). 5) When the following dialog box appears, confirm and click on “OK”.
USB Flash Memory U2M Security Software Installation Manual 6) The following dialog box appears, and then automatically disappears. 7) When the following dialog box appears, confirm and click on “OK” to complete formatting. 2. Changing the Security Software Password and Log In/Log Out Be sure to make security software password changes and login/log out when TransMemory™ is connected to the computer. 2.
USB Flash Memory U2M Security Software Installation Manual 2) When the following dialog box appears, click on “Change Password”.
USB Flash Memory U2M Security Software Installation Manual 3) When the following dialog box appears, enter the “Old Password”, then the “New Password”, re-enter the “Confirm New Password”, then a “Hint”.
USB Flash Memory U2M Security Software Installation Manual 4) When the “Old Password”, “New Password”, “Confirm New Password”, and “Hint” have been entered, click on “OK”. 5) When the following dialog box appears, confirm and click on “OK”.
USB Flash Memory U2M Security Software Installation Manual 2.2 Logging into the Privacy Zone using the security software 1) When the following dialog box appears, enter the “Password”. 2) When the “Password” has been entered, click on “OK”. 3) When the following dialog box appears, confirm and click on “OK”.
USB Flash Memory U2M Security Software Installation Manual 4) When the following dialog box appears, logging into the Privacy Zone is complete. 2.3 Logging out of the Privacy Zone using the security software 1) Double click on “Logout Privacy Zone” to log out. 2) When the following dialog box appears, click on “OK”.
