TOSHIBA AMERICA INFORMATION SYSTEMS STORAGE DEVICE DIVISION IRVINE, CALIFORNIA SD-R5002 DVD REWRITEABLE DRIVE USER MANUAL
CONTENTS Introduction..............................................................................1 Setup ........................................................................................3 Using the DVD Rewriteable Drive ...........................................7 Troubleshooting.....................................................................10 Specifications ........................................................................11 Drive Connectors.............................................
INTRODUCTION – SD-R5002 General Features Reads and records digital data on DVD-R/-RW and CD-R/-RW discs CD-R/-RW disc write/rewrite at 16X/10X DVD-R/-RW disc write/rewrite at 2X/1X 3-way Disc Eject (eject button, software, emergency eject hole) Average Random Access Time CD DVD-ROM 110ms 130ms Horizontal or Vertical Mount 2MByte Buffer Playback interchangeability for CD-ROM and DVD-ROM discs Regionalization (RPC2 compliance) (DVD) BUS Interface - ATAPI Types of Disc Formats Supported - Write • Applicable
Front Panel Figure 1.SD-R5002 DVD Writeable Drive Front Panel Loading Tray Load disc using tray. Busy Light LED The LED lights green or amber when the drive is operating (LED is amber when drive is writing.) Eject Button The Eject button is used to open the disc tray so you can install or remove a disc. Emergency Eject Hole The emergency eject hole is to be used only when the Loading Tray will not open when Eject button is pressed.
SETUP – SD-R5002 The following steps must be performed to properly install your drive: • Set Drive Jumper Settings • Connect Audio Cable • Attach IDE BUS Cable • Attach Power Cable • Mount Drive Jumper Settings The mode select jumpers are 6 straight angle pins located on the rear of the DVD Rewriteable drive.
Placing DVD Rewriteable Drive inside your Computer Now that you have set the jumpers, you are ready to install your DVD Rewriteable drive inside your computer. Important Note: Disconnect power from your computer system before beginning installation. Remove computer cover and faceplate if required. Refer to your computer systems manual for removal information. If the DVD Rewriteable drive is replacing a CD-ROM or DVD-ROM, remove drive presently installed in your system.
Power Cable - Connect an internal computer power supply cable to the power socket at the back of the DVD Rewriteable drive. One side of the plug has chamfered edges, so the power connector fits only one way. Push plug completely into the socket making sure the plug fits correctly. Figure 4.Installing Power Cable Audio Cable (optional) - If you have a sound card and speakers, and would like to play audio CDs on your computer, you will need to install a CD/DVD audio cable.
Software Driver - Toshiba's optical drives do not require any unique device drivers for Windows '95/'98/2000/Me/XP/NT. After installing your drive and re-booting, your system should recognize your drive. Windows '95/'98/2000/Me/XP/NT Operating Systems support all Toshiba optical drives natively If you prefer using DOS, download the DOS ATAPI driver from our web site. Other Software - Additional software is required to use the SD-R5002 CD-R/-RW, DVD-R/-RW and DVD functions.
USING THE DVD Rewriteable Drive – SD-R5002 Drive Operation Inserting a Disc - Horizontally To insert a disc into a drive that is mounted horizontally, perform the following steps: Figure 1.Inserting Disc 1. Open the drive's Loading tray by pressing the Eject Button. 2. Place disc or into drive's Loading tray 3. Press Eject button again or gently push on the open disc tray. Tray will automatically close.
Figure 2.Inserting Disc Vertically Removing a Disc To remove a disc from the DVD Rewriteable drive, perform the following steps: 1. 2. 3. 4. Open the Loading Tray by pressing the Eject Button. Slide disc holders away from disc. Grasp disc by edges, and lift out of loading tray. Press Eject Button again to close Loading Tray. Software When you purchase the SD-R5002 as a Kit, it will include Nero6 OEM Suite Software.
Usage Guidelines • • • • • Keep the disc tray closed when not using the DVD Rewriteable Drive. Do not press down on the disc tray when opening or closing it. Do not place objects on the disc tray. Never use a damaged, broken, or deformed disc. Do not press the Open/Close button while the drive is playing a DVD movie or accessing a disc. To stop a DVD movie, click Stop button in the DVD player application program. NOTE: High-speed drives spin the disc at a high rotational speed.
TROUBLESHOOTING – SD-R5002 Solution Problem Disc tray cannot be opened • • Check that there is power to drive. Use Emergency Eject instructions to open tray. Drive is not recognized by system • Is the drive connected properly? Are all cables plugged in properly (e.g. Power Cable, Interface Cable and Audio Cables).
SPECIFICATIONS –SD-R5002 General Interface: ATAPI Applicable Formats - Write: Write Formats Disc at once, Track at once, session at once, Packet Write, incremental write, CD-R/RW restricted overwrite DVD-R/RW Write Disc CD-R/-RW DVD-R/-RW CD-DA, CD+(E)G, CD-MIDI, CD-ROM, CD-ROM XA, CD-I, MIXED MODE CD, CD-I Bridge (Photo-CD, Video-CD), Multi-session CD (Photo-CD, CD-Extra, Portfolio), DVD-R (Ver 2.0 for General), DVD-RW (Ver1.
Performance Rotational Speed DVD-ROM (single layer) DVD-ROM (dual layer) DVD-R (Ver. 1.0) DVD-R (Ver. 2.0) DVD-RW (Ver 1.1) DVD-video (CSS-Disc) DVD-R (Ver 2.0) (Write) DVD-RW (Ver 1.1) (Write) CD-ROM, CD-R CD-RW CD-DA Transfer CD-DA, Video-CD CD-R (Write) High Speed CD-RW (Write) CD-RW (Write) 7,580rpm (5.0 - 12X CAV) 5,053rpm (3.3 - 8X CAV) 3,200rpm (2 - 4.8X CAV) 2,780rpm (2 - 4.8X CAV) 2,780rpm (2 - 4.8X CAV) 2,780rpm (2 - 4.
Reliability MTBF Power ON Hours ON/OFF Cycles Number of Access Operating Duty Cycle MTTR 100,000 hours 5,436 hours/year 313 cycles/year 600,000 accesses/year 20% of Power ON time (Reading/Seeking) 2% of Power ON time (Writing/Seeking) 0.
Regulatory The SD-R5002 DVD Writeable drive has been certified by the following regulatory agencies: 14 • UL 1950 • CSA C22.2 No.
DRIVE CONNECTORS –SD-R5002 Figure 1.SD-R5002 DVD Rewriteable Drive Rear Panel - Connectors Power Connector Power is supplied to your DVD drive by the connection with your computer's +5V/+12V power cable to the power socket at the back of drive. One side of the plug has chamfered edges, so the power connector fits only one way. CAUTION: Severe damage to the Drive circuits may occur if power cable is plugged in upside-down with power ON. Audio Connectors Supplies Analog and Digital sound to your system.
Table 1.Interface Pin Assignments INTERFACE PIN ASSIGNMENT PIN NO. 1 2 3 4 5 I/O I I/O I/O I/O SIGNAL NAME Reset GND HD7 HD8 HD6 6 7 I/O I/O 8 9 10 11 12 13 14 15 16 17 18 19 20 16 HOST SIGNAL NAME I/O Host Data Bus BIT 7 Host Data Bus BIT 8 Host Data Bus BIT 6 PIN NO.
