X300 Series Resource Guide Keep this guide in a convenient place to access important information about your computer. If you need assistance: ❖ ❖ Toshiba’s Support Web site pcsupport.toshiba.
Contents Introduction ...................................................................................... 21 Setting up your computer and getting started................................... 23 Adding memory (optional)................................................................ 27 Your computer’s TFT display ............................................................. 34 Inserting an ExpressCard® ............................................................... 34 Removing an ExpressCard® ...........
Handling the cord on this product will expose you to lead, a chemical known to the State of California to cause birth defects or other reproductive harm. Wash hands after handling. Model: Qosmio® X300 Series Recordable and/or ReWritable Drive(s) and Associated Software Warranty The computer system you purchased may include Recordable and/or ReWritable optical media drive(s) and associated software, among the most advanced data storage technologies available.
Critical Applications The computer you have purchased is not designed for any “critical applications.” “Critical applications” means life support systems, medical applications, connections to implanted medical devices, commercial transportation, nuclear facilities or systems or any other applications where product failure could lead to injury to persons or loss of life or catastrophic property damage.
Although the initial emphasis is in Europe, Toshiba is already working with design engineers, suppliers, and other partners to determine appropriate worldwide product life cycle planning and end-of-life strategies for our products. Please contact your local government for applicable laws and regulations governing the disposal of this product. For information on how to trade-in or recycle your product, visit www.reuse.toshiba.com.
Using this Equipment in Japan In Japan, the frequency bandwidth of 2,400 MHz to 2,483.5 MHz for second generation low-power data communication systems such as this equipment overlaps that of mobile object identification systems (premises radio station and specified low-power radio station). 1. Sticker Please put the following sticker on devices incorporating this product.
The Name of the radio equipment: refer to the equipment label provided on the computer JAPAN APPROVALS INSTITUTE FOR TELECOMMUNICATIONS EQUIPMENT Approval Number: D01-1128JP TELECOM ENGINEERING CENTER Approval Number: 03NY.A0018, 03GZDA0017 The following restrictions apply: ❖ ❖ ❖ Do not disassemble or modify the device. Do not install the embedded wireless module into other device. 5.17 GHz to 5.23 GHz for indoor use only.
Russia Slovenia Sweden UAE (United Arab Emirates) Uruguay Saudi Arabia South Korea Switzerland/Liechten stein Ukraine Slovakia Spain Taiwan (ROC) United Kingdom USA Venezuela Europe - Restrictions for use of 2.4 GHz Frequencies in European Community Countries België/ Belgique: Deutschland: France: Italia: Nederland: For private usage outside buildings across public grounds over less than 300m no special registration with IBPT/BIPT is required.
Europe - Restrictions for Use of 5 GHz Frequencies in European Community Countries European Community Countries 5150-5250 MHz 5250-5350 MHz Channels: 36, 40, 44, 48 Austria Belgium, France, Switzerland/Liechtenstein Denmark, Finland, Germany, Greece, Ireland, Italy, Luxembourg, Netherlands, Norway, Portugal, Sweden, UK Iceland, Spain 5470-5725 MHz Channels: 52, 56, 60, Channels: 100, 104, 108, 112, 64 116, 120, 124, 128, 132, 136, 140 Indoor Only O O Indoor Only x O Indoor/Outdoor x x O O O O
Approved Countries/Regions for use for the Atheros AR5BXB63 11g minicard This equipment is approved to the radio standard by the countries/regions in the following table. Do not use this equipment except in the countries/regions in the following table. This device works on passive scan only. A peer-to-peer mode is not available in 802.11a and Turbo Mode.
Approved Countries/Regions for use for the Intel® PRO/Wireless LAN 2100 3B Mini PCI Adapter This equipment is approved to the radio standard by the countries/regions in the following table. Do not use this equipment except in the countries/regions in the following table.
Jordan Kuwait Lesotho Luxembourg Malta Morocco Nicaragua Oman Papua New Guinea Philippines Puerto Rico Romania Senegal Slovak Republic South Korea Sweden Thailand UAE (United Arab Emirates) USA Yemen Kazakhstan Latvia Liechtenstein Macedonia Mexico Netherlands Nigeria Pakistan Paraguay Poland Qatar Russia Serbia and Montenegro Slovenia Spain Switzerland Turkey United Kingdom Kenya Lebanon Lithuania Malaysia Monaco New Zealand Norway Panama Peru Portugal Rep.
802.11a (5 GHz) Australia Chile Indonesia New Zealand USA Brunei Hong Kong Malaysia Saudi Arabia Venezuela Canada India Mexico Taiwan Vietnam Approved Countries/Regions for the Intel® Wireless Wi-Fi® Link 4965AGN This equipment is approved to the radio standard by the countries/regions in the following table. Do not use this equipment except in the countries/regions in the following table. An adhoc mode is available in Ch1-Ch11(802.11b/g), An Infrastructure mode is available in Ch1-Ch11 (802.
Connection compatibility with the wireless equipment in Draft 11n mode is not guaranteed. The Draft 11n function cannot be used with WEP/TKIP. Draft 11n mode can be used only with WPA-PSK(AES) mode or no security mode.
Approved Countries/Regions for use (Bluetooth® wireless technology) Bluetooth® Card from Toshiba equipment is approved to the radio standard by the countries/regions in the following table. Do not use this equipment except in the countries/regions in the following table.
❖ Using the equipment with Bluetooth wireless technology on board airplanes, or ❖ In any other environment where the risk of interference to other devices or services is perceived or identified as harmful. If you are uncertain of the policy that applies on the use of wireless devices in a specific organization or environment (e.g. airports), you are encouraged to ask for authorization to use the device with Bluetooth wireless technology prior to turning on the equipment.
Using this Equipment in Japan In Japan, the frequency bandwidth of 2,400 MHz to 2,483.5 MHz for second generation low-power data communication systems such as this equipment overlaps that of mobile object identification systems (premises radio station and specified low-power radio station). 1. Sticker Please put the following sticker on devices incorporating this product.
The following restrictions apply: ❖ ❖ Do not disassemble or modify the device. Do not install the embedded wireless module into other device. Optical Drive Safety Instructions This appliance contains a laser system and is classified as a CLASS 1 LASER PRODUCT. To use this model properly, read the user’s guide carefully and keep it for your future reference. Never attempt to disassemble, adjust or repair an optical drive. You could damage the drive.
Export Administration Regulation This document contains technical data that may be controlled under the U.S. Export Administration Regulations, and may be subject to the approval of the U.S. Department of Commerce prior to export. Any export, directly or indirectly, in contravention of the U.S. Export Administration Regulations is prohibited. Notice The information contained in this manual, including but not limited to any product specifications, is subject to change without notice.
Trademarks Qosmio is a registered trademark of Toshiba America Information Systems, Inc. and/or Toshiba Corporation. Microsoft, Outlook, Windows, and Windows Vista are either registered trademarks or trademarks of Microsoft Corporation in the United States and/or other countries. DirectX, Active Desktop, DirectShow, and Windows Media are registered trademarks of Microsoft Corporation. ConfigFree is a trademark of Toshiba Corporation. Wi-Fi is a registered trademark of the Wi-Fi Alliance.
Introduction 21 Introduction Welcome to the world of powerful and portable multimedia computers! Some software may differ from its retail version (if available), and may not include user manuals or all program functionality. Your Computer model may be ENERGY STAR® compliant. If the model you purchased is compliant, it is labeled with the ENERGY STAR® logo on the computer and the following information applies.
Introduction This computer is compatible with European Union Directive 2002/95/EC, Restriction of the use of certain Hazardous Substances in electrical and electronic equipment (RoHS), which restricts use of lead, cadmium, mercury, hexavalent chromium, PBB, and PBDE. Toshiba requires its computer component suppliers to meet RoHS requirements and verifies its suppliers’ commitment to meeting RoHS requirements by conducting component sampling inspections during the product design approval process.
Setting up your computer and getting started 23 Other icons used Additional icons highlight other helpful or educational information: TECHNICAL NOTE: This icon indicates technical information about the computer. HINT: This icon indicates helpful hints and tips. DEFINITION: This icon indicates the definition of a term used in the text. Other documentation Your computer comes with the following documentation in addition to this resource guide: ❖ ❖ An electronic version of the user’s guide.
Setting up your computer and getting started Never allow any liquids to spill into any part of your computer, and never expose the computer to rain, water, seawater or moisture. Exposure to liquid or moisture can cause electric shock or fire, resulting in damage or serious injury. If any of these eventualities should accidentally occur, immediately: 1. Turn off the computer. 2. Disconnect the AC adaptor from the power plug socket and computer. 3. Remove the battery pack.
Setting up your computer and getting started 25 Connecting to a power source Your computer requires power to operate. Use the power cord/cable and AC adaptor to connect the computer to a live electrical outlet, or to charge the computer’s battery. Never pull on a power cord/cable to remove a plug from a socket. Always grasp the plug directly. Failure to follow this instruction may damage the cord/cable, and/or result in a fire or electric shock, possibly resulting in serious injury.
Setting up your computer and getting started To connect AC power to the computer: 1 Connect the power cord/cable to the AC adaptor. (Sample Illustration) Connecting the power cord/cable to the AC adaptor Handling the cord on this product will expose you to lead, a chemical known to the State of California to cause birth defects or other reproductive harm. Wash hands after handling. 2 Plug the AC adaptor cord into the DC-IN on the back of the computer.
Adding memory (optional) 27 Connecting a printer Your printer documentation may require you to install the printer software before physically connecting the printer to your computer. If you do not install the software as instructed by the printer manufacturer, the printer may not function correctly. Read the documentation that came with your printer. Follow the manufacturer’s instructions when connecting a printer. You can connect a USB-compatible printer to your computer through the USB ports.
Adding memory (optional) Installing a memory module Memory modules can be installed in the memory module slots on the base of the computer. You will need a small Phillips screwdriver for this procedure. If the computer has been running recently, the memory module may be hot. The surrounding area may also be hot. Allow the module to cool to room temperature before replacing it. Avoid touching the cover, the module, and the surrounding area before they have cooled.
Adding memory (optional) 2 Click Shut Down. The operating system turns off the computer. 3 Unplug and remove any cables connected to the computer, including the AC adaptor. 4 Remove the main battery. For information on removing the main battery, see “Removing the battery from the computer” on page 42. 5 Close the display panel and turn the computer upside down to locate the memory module slot cover.
Adding memory (optional) Static electricity can damage the memory module. Before you handle the module, touch a grounded metal surface to discharge any static electricity you may have built up. Avoid touching the connector on the memory module or on the computer. Grease or dust on the connector may cause memory access problems. 9 Carefully remove the new memory module from its antistatic packaging, without touching its connector. 10 Locate an empty memory module slot on the underside of the computer.
Adding memory (optional) 31 12 Firmly press the memory module into the memory slot’s socket at approximately a 30-degree angle (to the horizontal surface of the computer). (Sample Illustration) Inserting the memory module into the socket 13 Once the module’s connector is fully inserted into the socket, press downward on the top edge of the module to seat the module into the latches at the sides of the socket.
Adding memory (optional) Slot B Slot A Front of computer (Sample Illustration) Inserting the memory module into the slot For this model Slot A is the bottom slot. Slot B is the top slot. If only one memory module is to be installed, it must be installed in Slot A. 14 Replace the memory module slot cover and secure it using the screw. 15 Re-insert the main battery. For more information on inserting the main battery, see “Inserting a charged battery” on page 43. 16 Turn the computer right side up.
Adding memory (optional) 33 The following screen may appear when you turn on the power: If “Start Windows® Normally” is highlighted, then press Enter. If one of the Safe Mode options is highlighted, it is best to press Enter to go into Safe Mode, then shut down and restart the system, at which time Windows® should boot back up normally. When Safe Mode is suggested, this could be a sign that you may need to scan your internal storage drive for errors or defragment the drive.
Your computer’s TFT display Your computer’s TFT display Small bright dots may appear on your screen display when you turn on your computer. Your display contains an extremely large number of thin-film transistors (TFT) and is manufactured using highprecision technology. Any small bright dots that may appear on your display are an intrinsic characteristic of the TFT manufacturing technology. Over a period of time, and depending on the usage of the computer, the brightness of the screen will deteriorate.
Learning the basics 35 Learning the basics Computing tips ❖ Save your work frequently. Your work stays in the computer’s temporary memory until you save it to the internal storage drive. If the network you are using goes down and you must restart your computer to reconnect, or your battery runs out of charge while you are working, you will lose all work since you last saved. HINT: Some programs have an automatic save feature that can be activated.
Using the optical drive Scrolling with the TouchPad™ There are two active regions on the TouchPad™ that allow you to scroll as you would with any wheel device on a mouse or trackball. To scroll vertically, run your finger up or down along the right edge of the TouchPad. To scroll horizontally, run your finger along the bottom edge of the TouchPad. This feature can be disabled or changed in the Mouse Properties dialog box.
Using the optical drive Your optical drive may look like this: Drive in-use indicator light Eject button Manual eject hole (Sample Illustration) Optical drive Drive in-use indicator light—Indicates when the drive is in use. Eject button—Press to release the disc tray. Do not press the eject button or turn off the computer while the drive in-use indicator light is glowing. Doing so could damage the disc or the drive. When the disc tray is open, be careful not to touch the lens or the area around it.
Using the optical drive The Stop button stops a disc that is currently playing. The Previous track button returns to the preceding track on the disc. The Next track button skips to the following track on the disc. The Mute button allows you to mute the sound. The Panel lights button turns all of the computer panel lights on and off. The Web Camera button launches the Web Camera. The Dolby® settings button launches the Dolby® controls.
Using the optical drive 7 39 Gently press the disc onto the center spindle until it clicks into place. Handle DVDs and CDs carefully, making contact only with the center hole and edge. Do not touch the surface of the disc. Do not stack discs. If you incorrectly handle the discs, you could lose data. 8 Make sure the disc is completely on the spindle and is lying flat on the tray. If you insert the disc incorrectly, it may jam the drive. If this happens, contact Toshiba support for assistance.
Moving the computer Moving the computer Before moving your computer, even across the room, make sure all drive activity has ended (the drive indicator light stops glowing) and all external peripheral cables are disconnected. Do not pick up the computer by its display panel or by the back (where the ports are located). Doing so could damage the system.
Mobile computing 41 TECHNICAL NOTE: Depending on your system, the RTC battery may only charge while the computer is turned on. Monitoring main battery power The computer’s main battery light gives you an indication of the main battery’s current charge. The following also applies to the secondary battery (available on certain models) if installed.
Mobile computing Changing the main battery When your main battery has run out of power, you have two options: plug in the AC adaptor or install a charged main battery. Never short circuit the battery pack by either accidentally or intentionally bringing the battery terminals in contact with another conductive object. This could cause serious injury or fire, and could also damage the battery pack and computer. ❖ Never expose a battery pack to abnormal shock, vibration or pressure.
Mobile computing 6 Slide the battery release latch to release the battery. 7 Pull the discharged battery out of the computer. 43 (Sample Illustration) Removing the battery If the battery is leaking or its case is cracked, put on protective gloves to handle it, and discard it immediately. Always dispose of used battery packs in compliance with all applicable laws and regulations.
Taking care of your battery Taking care of your battery The following sections offer tips on how to take care of your battery and prolong its life. Safety precautions ❖ ❖ ❖ ❖ ❖ ❖ ❖ ❖ ❖ ❖ ❖ If the battery pack produces an odor, overheats or changes color or shape while it is being used or charged, turn off the computer’s power immediately and disconnect the power cord/cable from the power socket. Carefully remove the battery pack from the computer. Do not try to disassemble a battery pack.
Taking care of your battery ❖ ❖ ❖ ❖ 45 3 Operate the computer on battery power for five minutes. If the battery pack has at least five minutes of operating time, continue operating until the battery pack is fully discharged. If the battery light flashes or there is some other warning to indicate a low battery, go to step 4. 4 Connect the AC adaptor to the computer and the power cord/cable to a power outlet.
If something goes wrong After repeated use, the batteries will finally lose their ability to hold a charge and you will need to replace them. Under certain applicable laws and regulations, it may be illegal to dispose of old batteries by placing them in the trash. Please be kind to our shared environment. Check with your local government authority for details regarding where to recycle old batteries or how to dispose of them properly.
If something goes wrong 47 To power off your computer: 1 Click Start, and then click the arrow next to the Lock button in the lower-right part of the Start menu. The Shut Down menu appears. Arrow Start Shut Down Menu (Sample Image) Shut Down menu 2 Select Shut Down. The computer shuts down completely. Problems when you turn on the computer These problems may occur when you turn on the power. The computer will not start.
If something goes wrong Your computer may be in Sleep mode and have a software or resource conflict. When this happens turning the power on returns you to the problem instead of restarting the system. To clear the condition, press Ctrl, Alt, and Del simultaneously. Then shut down the computer via software, or follow the steps if your program stops responding (see “Problems that are easy to fix” on page 46). Clearing the condition may get the computer running, but it will not solve a resource conflict.
If something goes wrong 49 Small bright dots appear on your TFT display when you turn on your computer. Small bright dots may appear on your screen display when you turn on your computer. Your display contains an extremely large number of thin-film transistors (TFT) and is manufactured using highprecision technology. Any small bright dots that may appear on your display are an intrinsic characteristic of the TFT manufacturing technology.
If you need further assistance The computer stops working (hangs) when you insert an ExpressCard®. The problem may be caused by an I/O (input/output) conflict between the socket and another device in the system. Use Device Manager to make sure each device has its own I/O base address. See “Fixing a problem with device manager” in the electronic user’s guide for more information. Since all ExpressCards® share the same socket, each card is not required to have its own address.
Power cord/cable connectors 51 Toshiba voice contact Before calling Toshiba, make sure you have: ❖ Your computer’s serial number ❖ The computer and any optional devices related to the problem ❖ Backup copies of your Windows® operating system and all other preloaded software on your choice of media ❖ Name and version of the program involved in the problem along with its installation media ❖ Information about what you were doing when the problem occurred ❖ Exact error messages and when they occurred For tec
Index A AC adaptor 25 AC power light 25 B backing up files 35 battery changing 42 installing 42, 43 notification 41 real-time clock (RTC) 40 removing 42 buttons eject, optical drive 37 TouchPad control 36 C CD/DVD inserting 38 changing main battery 42 computer moving 40 setting up 28 computing tips 35 connecting AC adaptor 25 power cord/cable 26 printer 27 control buttons TouchPad 36 D DC-IN 26 display problems screen is blank 48 E eject button optical drive 37 ExpressCard® inserting 34 removing 34
N R notification low battery 41 real-time clock (RTC) battery 40 removing CD/DVD with computer off 39 with computer on 39 main battery 42 memory module 32 O optical drive eject button 37 inserting a disc 38 removing disc 39 using 36 P power cable connectors 51 cord/cable 26 power problems computer will not start 47 precautions 23 primary button TouchPad 36 printer connecting 27 problem solving computer hangs when ExpressCard® inserted 50 computer will not start 47 contacting Toshiba 50 display is bl
GMA500627010 05/08