Total Care in Bathing Manufactured by Hydro Dimensions INSTALLATION & OPERATING INSTRUCTIONS To be provided to the owner/user. CUSTOMER SERVICE Contact Customer Service at (866) 292-5546 Monday – Friday 8:00 – 5:00 PST.
Total Care in Bathing Manufactured by Hydro Dimensions Warranty Confirmation & Product Registration Information (please save for your records) IMPORTANT: To ensure that your warranty is registered and confirmed with the manufacturer, please take a few moments to complete, sign and return the Product Registration Card (below) within 30 days of date of purchase. WARRANTY CONFIRMATION: By returning this product Registration Card we confirm the date of purchase for your new walk-in bathtub.
Hydro Dimensions Product Registration Card To ensure your warranty is registered with Hydro Dimensions complete, sign and return this registration card within 30 days of the purchase or installation.
This page intentionally left blank.
IMPORTANT SAFETY INSTRUCTIONS PERTAINING TO RISK OF FIRE, ELECTRIC SHOCK, OR INJURY TO PERSONS. WARNING: When using this unit, basic precautions should be followed, including the following: READ AND FOLLOW ALL INSTRUCTIONS DANGER! TO REDUCE THE RISK OF INJURY: A. Do not permit children to use this unit unless closely supervised by an adult. Supervision is also required when an elderly or handicapped individual uses the walk-in bath. B. Use this unit only for its intended use as described in this manual.
L. A thermostatic mixing valve is required, and must be provided by the installer. Section 414.5 of the 2009 Uniform Plumbing Codes require that the maximum hot water temperature discharging from the bathtub and/or whirlpool bathtub shall be limited to 120°F (49°C) by a device that conforms to ASSE 1070 or CSA B125.3. The water heater thermostat shall not be considered a control for meeting this provision. LI. The water in a walk-in tub should never exceed 40°C (104°F).
INSTALLATION INSTRUCTIONS READ ALL INSTRUCTIONS CAREFULLY BEFORE INSTALLATION WARNING: WHEN USING ELECTRICAL PRODUCTS, BASIC PRECAUTIONS SHOULD ALWAYS BE FOLLOWED, INCLUDING THE FOLLOWING: DANGER: RISK OF ELECTRICAL SHOCK. Connect only to a circuit protected by a ground-fault circuit interrupter (GFCI). Grounding is required. All electrical connections should be made by licensed electricians in accordance with national electrical codes and procedures.
INSTALLATION PROCEDURES: 1. For rough-in dimensions, see installation detail below. 2. The bathtub must be set on a solid flat surface capable of supporting the tub using all six (6) adjustable feet. It is required that all six (6) feet come in contact with the floor. 3. The plumbing connections (faucet, hoses, and waste/overflow) should be made prior to setting the tub in place. 4. The filler panel is used only for 60” installations. 5. The door drain assembly is attached at one end at the factory.
ELECTRICAL INSTRUCTIONS: HYDRO MASSAGE SYSTEM 1. Hydro massage system requires one (1) dedicated 15-amp, 120 volt service. 2. A receptacle with a 15-amp dedicated GFCI configuration must be provided by the electrician. NOTE: Provide a power supply outlet (receptacle) appropriately rated for the load. For voltage and current requirements refer to the label on each load. ELECTRICAL INSTRUCTIONS: AIR MASSAGE SYSTEM 1. Air massage system requires one (1) dedicated 15-amp, 120-volt service. 2.
ELECTRICAL INSTRUCTIONS: DUAL MASSAGE SYSTEM 1. Dual massage system requires two (2) dedicated 20-amp 120-volt GFCI circuits. 2. Two receptacles with 20-amp configuration each must be provided by the electrician. NOTE: Provide a power supply outlet (receptacle) appropriately rated for each load. For voltage and current requirements refer to the label on each load.
POST - INSTALLATION TESTING AND CLEANING: POST-INSTALL SYSTEM TEST: After installation, make sure all the plumbing, hydro massage and air massage system connections are correctly installed then run the following tests. 1. Before filling the tub with water, remove all loose debris from tub. Wipe down the door seal using a damp cloth, as well as the surface in the door jam that will come in contact with the door seal. 2. Fill the tub to the overflow and check for leaks.
CONGRATULATIONS! You made an excellent decision. You now own the best! Your walk-in tub was specifically designed to deliver continuous dependable operation. All whirlpool and air massage fittings are manufactured using strong, highly inert ABS and PVC materials to prevent water discoloration and ensure long life. The electrical components conform to, and exceed all, of the applicable safety standards.
HAND-HELD SHOWER OPERATION: 1. With the water on, push the diverter button down. Water will be diverted from the spout to the hand- held shower. 2. To adjust the spray setting, turn the control ring located on the outer edge of the showerhead. 3. To divert the water back to the spout, simply turn off the water supply. When you turn the water back on, the water will automatically flow out of the spout. AIR SYSTEM OPERATION: 1.
CARE AND MAINTENANCE Regular care of your walk-in tub with the hydro massage system will keep it clean and working at its best. This care should include the tub, the trim and fittings and internal water-carrying part of the pipe system. No maintenance is required for the pump or the motor powering it. The motor is lubricated for life. The shaft and seals in the pump are water lubricated and self-adjusting.
TROUBLESHOOTING GUIDE WARNING: Always turn off power at main electrical service panel when servicing your walk in bathtub. SYMPTOMS ● Motor will not start. PROBLEMS SOLUTIONS ● GFCI or breaker in off position. ● Disconnected or defective wiring • Improper air pressure in pump air hose line. ● Short between bath and breaker. • GFCI or breaker defective. ● Reset GFCI or breaker. ● Check and reconnect if needed. • Unplug then plug in air hose line at pump motor. ● Check for short in wiring.
LIMITED LIFETIME WARRANTY Section I This limited lifetime warranty is extended to the first user to be free from defects in workmanship and material under normal use and conditions for life from the date of original purchase. This warranty relates to all fitting and components included with the tub from the manufacturer. Different warranty periods apply. For the first year the tub and all component parts related to the product and labor are included.