Installation Manual: CST423EF, CST424EF(G), CST454CEF(G), CST743E, CST744E, CST744EL, CST744EF.10, CST754EF(N), CST784EF

2
ENGLISH
3
ENGLISH
TABLE OF CONTENTS
THANKS FOR CHOOSING TOTO!
The mission of TOTO is to provide the world with healthy, hygienic and more
comfortable lifestyles. We design every product with the balance of form and
function as a guiding principle. Congratulations on your choice.
Thanks for Choosing TOTO
®
! ............................................................................. 2
Common Tools Needed ...................................................................................... 2
Included Parts ...................................................................................................... 2
Before Installation ................................................................................................ 3
Installation Procedure .......................................................................................3-5
Toilet Tank Fill Valve Instructions .....................................................................5-6
Care and Cleaning ............................................................................................... 6
Warranty................................................................................................................ 7
Rough-In Dimensions ....................................................................................... 21
Replacement Parts ............................................................................................. 22
Check to make sure you have all these parts from the package:
COMMON TOOLS NEEDED
INCLUDED PARTS
• 10” adjustable wrench
• Carpenter’s Level
• Hacksaw
• Tape Measure
ADDITIONAL ITEMS (NOT SUPPLIED BY TOTO):
• Bowl Wax Ring
• Closet Flange Mounting Bolts
(usually 2 T-bolts, 2 metal washers and 2 nuts)
• Water Supply Line
(typically 1/2” compression to 7/8” ballcock)
• Toilet Seat (TOTO
SoftClose recommended)
• Hand Pliers
• Flat Screwdriver
• Putty Knife
China Bowl
Tank
a b
c
d
e f
Tank Lid Tank to Bowl Gasket
Tank to Bowl Hardware
a. Bolts (metal) - 2 c. Washers (metal) - 4
b. Washers (rubber) - 2 d. Nuts (metal) - 4
Flange Caps (for Bowl)
e. Caps (plastic) - 2 b. Base (plastic) - 2
BEFORE INSTALLATION
Read these instructions thoroughly before beginning work.
Please leave instructions for customers. These instruction contain maintenance
and warranty information.
If necessary, remove the existing toilet.
INSTALLATION PROCEDURE
In order for your new TOTO® toilet to fit correctly, the distance between the finished
wall to the center of the closet flange must be at 10 to 12 inches. This measurement
is called the Rough-In.
1) Clean any debris out of the closet flange
and then install new mounting bolts
(not supplied) into the slots of the closet
flange (see Illustration 1). The head of the
bolt should be inserted into the slot with
its threads facing upward.
2) Carefully turn the toilet upside down onto
some padding. Firmly press a new bowl
wax ring (not supplied) onto the circular
recess around the toilet bowl’s horn (see
Illustration 2). Turn the toilet upright and
gently lower into position over the closet
flange. With toilet properly aligned, press
firmly on both sides of toilet rim to set the
bowl wax ring (see Illustration 3).
CA UTION: Do not move the bowl after
the bowl wax ring is set. Thread the
nuts and tighten evenly until bowl is
snug to closet flange. Install the bolt
caps (see Illustration 3).
CA UTION: Do not over-tighten the nuts
as damage to the china bowl may
result.
Ill. 1
IMPORTANT!
Due to the powerful performance of our Cyclone, G-Max, E-Max and Power Gravity
flushing systems, they are not specified for back-to-back installations. The only
means of installing these toilets in a back-to-back situation is when the toilet drain
connections incorporate a WYE fitting. Please contact your builder or contractor prior
to this installation.
Double Combination WYE / 1/8 Bend
YES
Double Sanitary Tee / Sanitary Cross
NO
Finished Wall
Rough-In
Closet Flange
C/L
Supply Valve
C/L
Ill. 2
Wax Ring
Horn
Bolt Cap
Nut *
Washer *
Base Cap
Bowl Base
Three Points of Contact
* Not Supplied
Ill. 3