Owner Manual

50 51
Reference
What to Do?
If you cannot operate with the remote control
Operation is also possible using the buttons on
■
the Washlet control panel.
This button cannot be
used.
Washlet control panel
● The batteries may have worn out. Replace the batteries.
Replacing the batteries
■
1
Press on the Washlet control panel.
The POWER LED goes off.
•
2
Remove the remote control from the hanger.
(Page 16)
POWER LED
3
Open the cover and replace the AA batteries.
(Page 16)
4
Mount the remote control in the hanger.
5
Press on the Washlet control panel.
The POWER LED lights up.
•
About the batteries ■
Use dry cell, alkaline batteries. Follow the instructions below to prevent the batteries from rupturing or leaking fl uid.
●
When replacing the batteries, use new batteries of the same brand.
•
If you will not be using the remote control for a long time, remove the batteries.
•
Do not use rechargeable batteries.
•
Freeze Damage Prevention
In preparation for freezing conditions, such as in wintertime, take measures to prevent freezing.
Attention!
Do not use the energy-saver feature if there is a risk of the product being exposed to freezing temperatures.
●
(The product may be damaged.)
Warm the bathroom so that the temperature around the product is not below freezing or take other appropriate
●
measures against freezing temperatures.
Before starting work, set "AUTO OPEN/CLOSE" (S350e, TCF4732A, TCF4731A only) (Page 40) to "OFF".
●
1
Close the water supply valve.
The water supply stops.
•
Water supply valve
CAUTION
Do not remove the water fi lter
drain valve while the water supply
valve is open.
(Otherwise, water may leak out.)
2
Drain the water from the toilet tank.
Turn the fl ush handle
of the toilet tank to
the full fl ush side.
3
Release the pressure from the
water supply pipe.
Remove the remote control from the
1.
hanger, and press [MENU] on the rear
side.
(Page 16)
Use
2.
to select "CLEANING" and then
press [ENTER].
Use
3.
to select "WAND CLEANING
MODE ON/OFF", then press [ENTER].
The wand extends and water comes out.
In the [WAND CLEANING MODE ON/OFF]
4.
screen, press [ENTER] again.
The wand retracts.
Remove the cover.
5.
Cover
Remove the water fi lter drain valve.
6.
Water filter drain valve
Water collector
Drain the water from the water supply hose.
7.
Water supply hose
Position horizontally
After draining the water, mount the water
8.
fi lter drain valve.
Tighten it securely using a fl at-head screwdriver.
•
Water filter drain valve
Mount the cover.
9.
4
Check that the POWER LED on
the Washlet main display has lit up.
(Page 17)
5
Set the toilet seat temperature
to "High".
(Page 26)
(To maintain the temperature, close the toilet seat
and toilet lid after fi nishing work.)
When you use Washlet again, the water supply
■
and power supply will be required. (See below)
Resupplying the Water (After draining)
1
Open the water supply valve to
supply water.
Check that there are no leaks in the
•
plumbing or the Washlet.
2
[USA]
Insert the power plug.
[Asia, Oceania]
Switch the breaker on the
distribution board to ON.
3
Discharge water from the wand.
While pressing the left side of the toilet
1.
seat,
Press the "REAR" button on the remote
2.
control to discharge water from the
wand. (Catch the water in a paper cup
or other recipient.)
If the remaining water has frozen and
■
no water comes out
Heat the inside of the bathroom, and warm the
•
water supply hose and water supply valve using a
cloth soaked in warm water.