Instruction Manual WASHLET TCF4911EU, TCF4911U TCF4901EU, TCF4901U TCF4913EU, TCF4913U TCF4903EU, TCF4903U ■ Thank you for your recent purchase of the product. Please read the enclosed information to ensure the safe use of your product. ■ Be sure to read this Instruction Manual before using your product and keep it in a safe place for future reference. M08036_1_EN.
The available functions vary according to the model. Product name, Part No. Check your model name and write a check mark in this field as needed. Product name (Model) Part No. WASHLET TCF4911EU TCF4913EU TCF4901EU TCF4903EU TCF4911U Functions TCF4913U TCF4901U TCF4903U Your Model Ref.
Table of Contents Introduction Keep It Clean Safety Precautions...................... 4 Operational Precautions .......... 11 Parts Names .............................. 12 Preparation ................................ 16 Basic Operations................. 18 Automatic Functions (Cleaning Features) .................. 22 Deodorizer, Auto wand CLEAN, Auto bowl CLEAN, Bowl light, Indicator Automatic Functions (Convenience Features) .......... 24 Lights to show that the "clean" functions are operating.
Safety Precautions IMPORTANT SAFEGUARDS READ ALL INSTRUCTIONS BEFORE USING Symbols and Meanings WARNING May result in death or serious injury. CAUTION May result in injury or property damage. The following symbols are used to indicate important safety instructions for the use of the product. Symbol Meaning This symbol indicates a prohibited use of the product. This symbol is used to indicate a required step in the use of this product.
Do not use the Washlet if a malfunction occurs. In case of breakdown or other problem, be sure to cut off power by means such as unplugging the power plug. Close the water shutoff valve to stop water supply. Possible malfunctions: Water is leaking from a pipe or the main unit. The product is cracked or broken. The product makes a strange noise or emits a strange odor. The product emits smoke. The product is abnormally hot. The toilet seat cushion is out of place.
Safety Precautions (Continued) WARNING Refrain from sitting on the seat for long periods. It may cause low-temperature burns. To prevent the following persons from getting a moderate temperature burn during use, other person should turn off the toilet seat heater and set the dryer temperature to "Low". Young children, the aged and other users unable to set the temperature appropriately themselves. The ill, physically disabled and others who do not have freedom of movement.
Introduction WARNING When leaking battery fluid adheres to your body or clothes, wash it away with clean water. The fluid may damage your eyes or skin. Preliminary studies in females suggest that overuse of continuous spraying can increase the possibility of vaginal mucosa drying and potential reduction in desirable microbial organisms. Although these studies have not been validated, please consult your healthcare provider for concerns regarding whether these circumstances may apply to you.
Safety Precautions (Continued) CAUTION Do not fold or crush the water supply hose; do not damage by cutting with a sharp object. Doing so may cause water leaks. Do not install the base plate, which is not attached. Doing so may cause damage. If a water leak should occur, always close the shutoff valve. When the ambient temperature is likely to drop to 0°C or lower, prevent damage to the pipes and hoses due to freezing.
Introduction DANGER To reduce the risk of electrocution: 1. Do not use while bathing. 2. Do not place or store the product where it can fall or be pulled into a tub or sink. 3. Do not place in or drop into water or other liquid. 4. Do not reach for the product when it has fallen into water. Unplug immediately. WARNING To reduce the risk of burns, electrocution, fire or injury to persons: 1. Close supervision is necessary when this product is used by, on, or near children or invalids. 2.
Safety Precautions (Continued) Grounding Instructions This product should be grounded. In the event of an electrical short circuit, grounding reduces the risk of electric shock by providing an escape wire for the electrical current. The plug must be plugged into an outlet that is properly installed and grounded. DANGER - Improper use of the grounding plug can result in a risk of electric shock.
Operational Precautions ■For prevention of malfunctions Switch ON Gap The toilet seat lowers. Seat switch (Built-in) ●Sit back on the toilet seat. The seat switch will not turn on unless you sit on the seat properly. Introduction < About the seat switch > ●When you sit on the toilet seat, the seat switch turns ON, enabling you to use various features. (A click sound is heard when the seat switch is ACTIVATED.) ●Do not expose to direct sunlight.
Parts Names TCF4911EU, TCF4911U TCF4901EU, TCF4901U Main display Power LED Seat LED Energy saver LED Toilet lid cushions CLEAN indicator Toilet lid Body sensor (Built-in) Wand cover Seat Product name, part no., etc.
Introduction Right rear of main unit Toilet seat cushions Deodorizer outlet Left side of main unit Right side of main unit Water filter drain valve (Page 37) Remote control receiver Cover Main unit removal button (Pages 34, 35) Soft light*1 Deodorizing filter (Page 33) *1 Only used on models with "Soft light" function. 13 M08036_1_EN.
Parts Names TCF4913EU, TCF4913U TCF4903EU, TCF4903U Main display Power LED Seat LED Energy saver LED Toilet lid cushions CLEAN indicator Toilet lid Wand cover Product name, part no., etc. Seat switch (Built-in) Warm air outlet cover Wand Heated seat Power plug Shutoff valve Water drain lever (Page 17) Power cord Water supply hose 14 M08036_1_EN.
Introduction Right rear of main unit Toilet seat cushions Deodorizer outlet Left side of main unit Right side of main unit Water filter drain valve (Page 37) Remote control receiver Cover Main unit removal button (Pages 34, 35) Soft light*1 Deodorizing filter (Page 33) *1 Only used on models with "Soft light" function. 15 M08036_1_EN.
Preparation 1. Insert the battery 1 Remove the remote control from the hanger. Using the Product for the First Time If the remote control is secured (for anti theft) 1 Remove the screw from the remote control fixture. (View from side) Remote control Remote control Hanger Wall Hanger Screw Remove Phillips screwdriver 2 Open the battery cover and insert two AA batteries. 2 Remove the remote control from the hanger. ■To secure the remote control again Tighten and fix the screw.
1 2 Insert the power plug. The wand extends and then retracts. 3. Open the shutoff valve 1 Fully open the shutoff valve. Introduction 2. Turn on the power Check that the "Power" LED is lit up. When it is off, switch the "Power" to "ON". To operate from the back of remote control Press "Power ON/OFF" button about 3 seconds or longer. To operate from the front of remote control * Recommended if the remote control is locked to prevent theft.
Basic Operations Operate the controls on the remote control; a beep sounds when the main unit receives the signal. Opening and closing*1 ●Functions that operate when a button is pressed during "Rear cleansing", "Rear soft cleansing", "Front cleansing" or "Wide front cleansing". "Opening and closing the toilet seat" Opens and closes the toilet seat. Stopping "Stopping" Stops the operation. Note ●Sitting back on the toilet seat makes it easier to adjust the wand position and to reduce splashing.
● The "Water pressure adjustment", "Wand position adjustment" and "Personal setting lock" functions are swipe operated. ●Functions that operate when a button is pressed during "Rear cleansing", "Rear soft cleansing", "Front cleansing" or "Wide front cleansing". Note ●Sitting back on the toilet seat makes it easier to adjust the wand position and to reduce splashing. "Water pressure adjustment" *2 Operation You can select from 5 levels of water pressure.
Basic Operations About the Menu Screen This section is an overview of the settings that can be configured with the remote control. ●See the corresponding pages for the detailed descriptions. Remote control back side MENU Display screen 1/5 1.MANUAL CLEANING 2.ENERGY SAVER Menu, Return button •Adjust settings •Return to previous menu 3.
You can set as desired If you want to return to the previous item, press the Level 1 Level 2 MANUAL CLEANING button. ▶ Level 3 1/2 1.WAND CLEAN ING ON/OFF 2.MANUAL CLEAN Operation ENERGY SAVER Number of items on display*1 1/2 1.AUTO ENERGY SAVER 2.TIMER SAVER MENU AUTO OPEN /CLOSE 1/5 1.AUTO OPEN /CLOSE 1.MANUAL CLEANING 4. / / LANGUAGE 5.OTHER SETTING AUTO CLEANING 2.AUTO CLOSE DELAY 2.ENERGY SAVER 3.AUTO FUNCTION 1/4 AUTO FUNCTION 1/3 3.AUTO OPEN DELAY 1/4 1.AUTO WAND CLEAN 4.
Automatic Functions "ewater+" *1 is used automatically to clean the wand and bowl unit. Cleaning Features As you As you As you approach sit *2 stand up • Operation under the initial settings is described below.
Lights to show that the "CLEAN" functions are operating. Bowl light CLEAN indicator Lights to show that auto bowl CLEAN and auto wand CLEAN are operating. Lights to show that the "clean" functions are operating. Note Changing settings "ewater+" can also be used by pressing the remote control button Deodorizing filter needs regular maintenance.
Automatic Functions Various automatic functions are available. • Operation under the initial settings is described below. As you As you approach *1 sit Convenience Features As you stand up When using the toilet seat Opening the toilet lid automatically Auto open / close (lid)*2 The toilet lid closes The toilet lid opens (After about 90 seconds) When standing and using The toilet lid opens Open the toilet seat with the remote control.
As you move away Note Changing settings ON/OFF When the toilet lid is closed by hand, it The toilet lid and toilet seat close (About 90 seconds after moving away from the bowl unit by about 40 cm or more.) Lights up in low mode (Goes out after about 5 seconds) cannot open automatically for about 15 seconds. (Open and close manually.
Temperature Adjustment Warm Water, Toilet Seat, Drying Five different temperature levels from high to low and "OFF" can be set. 1 Remove the remote control from the hanger. 2 If the remote control is locked to prevent theft (Page 16) Press. 3 Select the item you want to set.
4 Select the temperature level. 5 WATER TEMP Mount the remote control in the hanger. If the remote control is locked to prevent theft (Page 16) SEAT TEMP DRYER TEMP Operation Warm water temperature Press OFF*1 Low High OFF Low High until [OFF] appears. Toilet seat temperature Press until [OFF] appears. When "OFF" is set, the "SEAT" LED will go off. Drying air temperature Low High The "Drying" cannot be turned "OFF".
Energy Saver Features Type "Auto energy saver", "Auto energy saver+" or "Timer energy saver" can be selected. To save energy, the temperature of the toilet seat becomes low (or "OFF"). ●"Auto energy saver" takes about 10 days to detect time periods in which the toilet seat is never or infrequently used. Type Auto energy saver Auto energy saver+ Timer energy saver Situation Energy saver is on Main display You want the Washlet to save energy automatically.
Main display When energy saver is in operation Toilet seat heater 4 6 8 5 9 0 Set temperature*1 Low temperature*2 Low temperature*2 Operation Low Lit (Orange) 0 PM Example: Used infrequently from 9 pm to 6 am Lit (Orange) OFF Lit AM Example: Not used from 0 am to 4 am Low Set temperature*1 OFF Low temperature*2 OFF Low temperature*2 OFF*3 Example: Set from 8 am to 5 pm OFF Lit (Green) Set temperature*1 Set temperature*1 OFF OFF*3 ● During "Auto e
Energy Saver Features How to Set Set the "Timer energy saver" at the time you want to start it. 1 2 Press. Auto energy saver Select [ENERGY SAVER]. 2/5 MENU Press 1.MANUAL CLEANING 2.ENERGY SAVER 3.AUTO FUNCTION Display screen MENU Auto energy saver+ 1/5 1.MANUAL CLEANING 2.ENERGY SAVER 3.AUTO FUNCTION Menu, Return button Select keys : Select the item or setting Enter Timer energy saver When energy saver is set, the "Energy saver" LED (green) lights up.
3 3 4 [AUTO ENERGY SAVER]. Select [AUTO ENERGY SAVER]. Select [AUTO ENERGY SAVER]. Select [AUTO ENERGY SAVER+]. 1/2 Press 1.AUTO ENERGY SAVER AUTO ENERGY SAVER Press OFF AUTO ENERGY SAVER ENERGY SAVER (To return 3 4 [TIMER SAVER]. Select [6H], [9H] or [OFF]. ) 1/2 Press 1.AUTO ENERGY SAVER AUTO ENERGY SAVER AUTO ENERGY SAVER+ ON Press OFF AUTO ENERGY SAVER (To return AUTO ENERGY SAVER Select AUTO ENERGY SAVER ON Operation 4 Select ENERGY SAVER ENERGY SAVER 2/2 ) Press 1.
Maintenance Main Unit Main Unit (Approximately daily) WARNING Always disconnect the power plug from the outlet before cleaning, maintenance or inspection. (Failure to do so may cause electric shock or malfunction, resulting in a breakdown.) For safety, disconnect the power plug before cleaning or maintenance.*1 The "Power" LED goes off. Lit OFF Soft cloth soaked in water 1 2 ・Toilet paper ・Dry cloth ・Nylon scrubbing brush (May cause damage.) Unplug the power plug.
Deodorizing Filter Wand Deodorizing Filter (Approximately once a month) 1 2 Unplug the power plug. 3 Remove the deodorizing filter. Hold the knob and pull outward. Do not pull with undue force. (May cause damage or malfunction.) Clean with a tool such as a toothbrush. When washing with water, dry off all water before mounting. Toothbrush, etc. 4 Mount the deodorizing filter. Push firmly until a click sound is heard. Deodorizing Filter 5 Insert the power plug. The "Power" LED lights up.
Maintenance Gap between the Main Unit and Bowl Unit {TCF4911EU, TCF4901EU, TCF4913EU, TCF4903EU} Gap between the Main Unit and Bowl Unit (Approximately once a month) You can remove the main unit to clean the top of the bowl unit and the bottom of the main unit. Soft cloth soaked in water 1 2 Toilet paper, etc. (May cause damage.) Unplug the power plug. Remove the main unit. Do not pull the unit with undue force (because the water supply hose and power cord are attached). (2) Lift up the main unit.
{TCF4911U, TCF4901U, TCF4913U, TCF4903U} Gap between the Main Unit and Bowl Unit (Approximately once a month) You can remove the main unit to clean the top of the bowl unit and the bottom of the main unit. Soft cloth soaked in water 1 Unplug the power plug. 2 Remove the main unit. Top of the bowl unit Toilet paper, etc. (May cause damage.) Base plate Do not pull the unit with undue force (because the water supply hose and power cord are attached).
Maintenance Gap between the Main Unit and the Toilet Lid Gap between the Main Unit and the Toilet Lid (Approximately once a month) The toilet lid can be removed for thorough cleaning. Soft cloth soaked in water 1 2 3 Toilet paper, etc. (May cause damage.) Unplug the power plug. Removing and Reinstalling Remove the main unit. (Pages 34, 35) Remove the toilet lid. Hold with both hands Slightly tilt the toilet lid to the front. ↓ Ⓐ : Pull the left side outward.
Water Filter Drain Valve Water Filter Drain Valve (Approximately once every 6 months) 1 Close the shutoff valve. The water supply stops. CAUTION Do not remove the water filter drain valve while the shutoff valve is open. 5 Clean with a tool such as a toothbrush. 6 Reinstall the water filter drain valve and cover. 7 Insert the power plug. 8 Open the shutoff valve. Also, remove any dust from inside the hole of the water filter drain valve.
Changing Settings Setting List Setting Types Auto open / close (lid) Auto close delay MENU Auto open / close (lid) 1/5 1.MANUAL CLEANING Auto open delay 2.ENERGY SAVER 3.
Available Settings Bold: Initial settings Set whether or not to open and close the toilet lid automatically Change the amount of time before the lid/ seat closes automatically Change the amount of time after which the lid/ seat opens automatically upon closing it with hands Automatically open and close the toilet lid/ Automatically open and close the toilet seat and toilet lid Set whether or not to clean the wand automatically Set whether or not to spray mist in the bowl unit automatical
Changing Settings Auto open / close (lid) 1 2 Press. Set whether or not to open and close the toilet lid automatically 3/5 MENU Select [AUTO FUNCTION]. 1.MANUAL CLEANING 2.ENERGY SAVER Press Auto open / close (lid) 3.AUTO FUNCTION 3 AUTO FUNCTION Select [AUTO OPEN/CLOSE]. Display screen AUTO OPEN /CLOSE 1/3 Press 1.AUTO OPEN /CLOSE 2.AUTO CLEANING Change the amount of time before the lid/seat closes automatically Auto close delay 1/4 1.AUTO OPEN /CLOSE 2.AUTO CLOSE DELAY 3.
4 5 Select [AUTO OPEN/CLOSE]. Select AUTO OPEN /CLOSE 1/4 1.AUTO OPEN /CLOSE AUTO OPEN /CLOSE Press ON [ON] or [OFF]. Press AUTO OPEN/CLOSE OFF OFF (To return 4 5 Select [AUTO CLOSE DELAY]. Select AUTO OPEN /CLOSE 1.AUTO OPEN /CLOSE 2/4 Press 2.AUTO CLOSE DELAY AUTO CLOSE DELAY 90S [25S] or [90S].*1 ) Press AUTO CLOSE DELAY 25S 25S (To return ) *1 When set to "25 seconds", the lid/seat does not open automatically for about 15 seconds after closing automatically.
Changing Settings Auto open / close (lid) (Continued) 1 2 Press. 3/5 MENU Change the time period till automatic opening (After closing by hand.) Select [AUTO FUNCTION]. 1.MANUAL CLEANING 2.ENERGY SAVER Press 3.AUTO FUNCTION 3 AUTO FUNCTION Select [AUTO OPEN/CLOSE]. Display screen AUTO OPEN /CLOSE 1/3 Press 1.AUTO OPEN /CLOSE 2.AUTO CLEANING Automatically open and close the toilet lid/ Automatically open and close the toilet seat and toilet lid 1/4 1.AUTO OPEN /CLOSE 2.AUTO CLOSE DELAY 3.
4 Select [AUTO OPEN DELAY]. AUTO OPEN /CLOSE 3/4 1.AUTO OPEN /CLOSE Press 2.AUTO CLOSE DELAY 3.AUTO OPEN DELAY 5 Select AUTO OPEN DELAY Press 15S [15S], [30S] or [90S]. 30S 90S 4 Select [SEAT / LID]. AUTO OPEN DELAY 30S AUTO OPEN /CLOSE (To return ) 4/4 2.AUTO CLOSE DELAY 3.AUTO OPEN DELAY Press 4.SEAT/LID 5 SEAT/LID Select LID [LID] or [SEAT·LID].
Changing Settings Cleaning Features 1 2 Press. Set whether or not to clean the wand automatically 3/5 MENU Select [AUTO 1.MANUAL CLEANING FUNCTION]. 2.ENERGY SAVER Press 3.AUTO FUNCTION 3 AUTO FUNCTION Select [AUTO CLEANING]. 1.AUTO OPEN /CLOSE 2/3 Press 2.AUTO CLEANING 3.LIGHT Display screen AUTO CLEANING Auto wand CLEAN Set whether or not to spray mist in the bowl unit automatically Auto bowl CLEAN 1/4 1.AUTO WAND CLEAN 2.AUTO BOWL CLEAN 3.
4 5 Select [AUTO WAND CLEAN]. Select AUTO CLEANING 1/4 1.AUTO WAND CLEAN AUTO WAND CLEAN Press ON [ON] or [OFF]. Press AUTO WAND CLEAN OFF OFF (To return 4 5 Select [AUTO BOWL CLEAN]. Select AUTO CLEANING 1.AUTO WAND CLEAN 2/4 Press 2.AUTO BOWL CLEAN AUTO BOWL CLEAN ON [ON] or [OFF]. ) Press AUTO BOWL CLEAN OFF OFF (To return ) Reference 45 M08036_1_EN.
Changing Settings Cleaning Features (Continued) 1 2 Press. Set whether or not to deodorize automatically after sitting on the toilet seat 3/5 MENU Select [AUTO FUNCTION]. 1.MANUAL CLEANING 2.ENERGY SAVER Press Deodorizer 3.AUTO FUNCTION 3 AUTO FUNCTION Select [AUTO CLEANING]. 1.AUTO OPEN /CLOSE 2/3 Press 2.AUTO CLEANING 3.LIGHT Display screen AUTO CLEANING Set whether or not to deodorize automatically after standing up Auto power deodorizer 1/4 1.AUTO WAND CLEAN 2.AUTO BOWL CLEAN 3.
4 5 Select [DEODORIZER]. AUTO CLEANING 3/4 Press 2.AUTO BOWL CLEAN 3.DEODORIZER DEODORIZER Select Press ON [ON] or [OFF]. DEODORIZER OFF OFF (To return 4 5 Select [AUTO POWER DEODORIZER]. Select AUTO CLEANING 4/4 2.AUTO BOWL CLEAN 3.DEODORIZER Press 4.AUTO POWER DEODORIZER AUTO POWER DEODORIZER ON [ON] or [OFF]. ) Press AUTO POWER DEODORIZER OFF OFF (To return ) Reference 47 M08036_1_EN.
Changing Settings Light 1 2 Press. 3/5 MENU Set whether or not to use the soft light Select [AUTO FUNCTION]. 1.MANUAL CLEANING 2.ENERGY SAVER Press Soft light 3.AUTO FUNCTION 3 AUTO FUNCTION Select 4/4 1.AUTO OPEN /CLOSE [LIGHT]. 2.AUTO CLEANING Press 3.LIGHT Set whether or not to use the light inside the bowl unit Bowl light Display screen LIGHT 1/3 1.SOFT LIGHT 2.BOWL LIGHT 3.
4 5 LIGHT 1/3 Press Select 1.SOFT LIGHT [SOFT LIGHT]. SOFT LIGHT Select Press ON [ON] or [OFF]. SOFT LIGHT OFF OFF (To return 4 5 LIGHT 2/3 Select Press 1.SOFT LIGHT [BOWL LIGHT]. 2.BOWL LIGHT BOWL LIGHT Select Press ON [ON] or [OFF]. BOWL LIGHT OFF OFF (To return 4 ) LIGHT ) 3/3 Select 1.SOFT LIGHT [INDICATOR]. 2.BOWL LIGHT Press 3.INDICATOR Reference 5 INDICATOR Select ON [ON] or [OFF]. Press INDICATOR OFF OFF (To return ) 49 M08036_1_EN.
Changing Settings Language Settings 1 2 Select the language displayed on the back of remote control Press. Select 2.ENERGY SAVER [ 语言 / 語言 / LANGUAGE]. Display screen Language Settings 4/5 MENU 3.AUTO FUNCTION 4. Press / / LANGUAGE / / LANGUAGE ENGLISH Menu, Return button Enter Select keys : Select the item or setting Items set on this display 1. 中文简体 "Simplified Chinese" 2. 繁體中文 "Traditional Chinese" 3. ENGLISH "English" 50 M08036_1_EN.
3 Select / / LANGUAGE LANGUAGE ENGLISH [ 中文简体 ], [ 繁體中文 ] or [ENGLISH]. Press ENGLISH (To return ) Reference 51 M08036_1_EN.
Changing Settings Other settings 1 2 Press. Select [OTHER SETTING]. Set whether or not to make a beep sound 5/5 MENU Beep sound 3.AUTO FUNCTION 4. / / LANGUAGE Press 5.OTHER SETTING Set whether or not to use the setting lock Display screen OTHER SETTING Setting lock 1/3 1.BEEP 2.SETTING LOCK 3.PERSONAL SETTING Menu, Return button Enter Select keys : Select the item or setting Items set on this display 1. BEEP "Beep sound" 2. SETTING LOCK "Setting lock" 3.
3 4 Select OTHER SETTING 1/3 Press 1.BEEP [BEEP]. BEEP Select Press ON [ON] or [OFF]. BEEP OFF OFF (To return 3 4 Select OTHER SETTING Select 2.SETTING LOCK SETTING LOCK SETTING LOCK Press OFF [ON] or [OFF]. 2/3 Press 1.BEEP [SETTING LOCK]. ) PRESS ENTER ON FOR 2 SEC TO RESET 5 Check the displayed screen. Cancellation method: SETTING LOCK PRESS ENTER FOR 2 SEC Display screen during setting lock TO RESET Press "Enter" for 2 seconds or longer.
Changing Settings Other settings (Continued) 1 2 Press. 5/5 MENU Select [OTHER SETTING]. Set whether or not to use the personal setting 3.AUTO FUNCTION 4. Press / / LANGUAGE 5.OTHER SETTING Display screen OTHER SETTING Personal setting Setting 1/3 1.BEEP 2.SETTING LOCK 3.
3 Select OTHER SETTING 3/3 1.BEEP [PERSONAL SETTING]. Press 2.SETTING LOCK 3.PERSONAL SETTING 4 5 3 Select PERSONAL SETTING 1/3 Press 1.SETTING [SETTING]. Select 2.REGISTER1 PERSONAL SETTING LOCK OFF SETTING Press ON [ON] or [OFF]. Select (To return OFF OTHER SETTING ) 3/3 1.BEEP [PERSONAL SETTING]. Press 2.SETTING LOCK 3.PERSONAL SETTING 4 Select PERSONAL SETTING 1.SETTING [REGISTER1] or [REGISTER2]. 2/3 Press 2.REGISTER1 3.
What to Do? If the water does not flow due to a water service interruption If you cannot operate with the remote control If the water does not flow due to a water service interruption 1 Use a bucket to flush water. 2 If the water level is low after flushing, add more water. Large bucket Pour strongly, aiming at the center of the bowl unit. • Prevents odors. Attention! Newspaper, dustcloth, etc. • When the water supply is restored, be sure to perform a full flush.
Freeze Damage Prevention When the ambient temperature is likely to drop to 0°C or lower, take measures to prevent freezing. Attention! • When the ambient temperature is likely to drop to 0°C or lower, do not use the energy saver feature. (May damage the product.) • Warm the bathroom or take measures against freezing so that the ambient temperature does not drop below 0°C. • Before starting work, set "Auto open/close (lid)" (Except TCF4901EU, TCF4901U, TCF4903EU, TCF4903U) (Page 40) to OFF.
What to Do? Long Periods of Disuse If the toilet is in a location you will not visit for a long time, drain the water. (The water in the tank may cause malfunctions or become contaminated and cause skin irritation or other problems.) How to drain the water 1 2 Drain the water from the toilet tank. (Page 57 Step 1 , 2 ) 6 Release your hand to return the water drain lever to its original position. Press "Wand CLEAN" button. • Open the wand cover. (Release the pressure from the water supply pipe.
Removal of Display Panel To remove the display panel, follow the procedure below. How to remove the display panel 1 Unplug the power plug. 2 Remove the remote control from the hanger. 3 Remove the hanger and display panel. • The "Power" LED goes off. (Page 16) Phillips screwdriver Screw Hanger Screw the hanger on the wall. 5 Mount the remote control in the hanger. 6 Insert the power plug. • The "Power" LED lights up. To install back the display panel, follow the procedure above.
Troubleshooting First, try the actions described on pages 60 to 65. If the problem persists, consult the installer, seller or TOTO customer service (see contact information on the back cover). CAUTION If a water leak occurs, close the shutoff valve. Shutoff valve Please check first ■ Is the "Power ON/OFF" setting "OFF"? Switch it to "ON" with the remote control. (Page 17 Step 2-2) Is the Power LED lit? ■ Is the "Power" LED on the main display flashing? The main unit is not mounted properly.
Rear Cleansing, Front Cleansing and Wand Please check Ref. Page ●When the temperature is low, it takes time for the wand to come out after the remote control button is pressed because the water must be warmed up first. - ●Did you sit on the toilet continuously for 2 hours or longer? (If so, operation is stopped for safety purposes.) Stand up from the seat and then use again.
Troubleshooting Warm air drying Trouble Please check The dryer temperature is low ●Is the dryer temperature set to low level? Stops in the middle of use ●The feature stops automatically after about 10 minutes of continuous use. ●Does the seat switch have difficulty detecting? Sit back on the toilet seat. If you get up slightly from the seat, or sit forward on the seat, the seating switch may temporarily stop detecting your presence. Ref.
Toilet Seat and Toilet Lid (Auto open/close (lid)) Trouble The toilet lid closes on its own The toilet lid and toilet seat open at the same time Stops (or closes) while opening Ref. Page Please check ●Is "Auto open/close (lid)" set to "ON"? You can turn it "OFF". ●Is "Auto close delay" set to "25 seconds"? ●The seat switch will not turn on unless you sit on the seat properly. Sit back on the toilet seat.
Troubleshooting Energy Saver Trouble Please check Ref. Page The Energy saver LED does not light up ●Did you unplug the power plug or was there a power outage? The "Energy saver" LED on the main display may go off when the power is turned on even if the energy saver feature is "ON". (It will turn on within about 24 hours since the setting is retained.
Others Trouble Ref. Page Please check ●If any nuts in a connection are loose, firmly tighten them with a tool such as a monkey wrench. Water is leaking from the plumbing connections Do not use tools on the water supply hose connection. Tighten it by hand. Water supply hose - Water supply hose connection If the water leak does not stop, close the shutoff valve and seek repair.
Specifications TCF4911EU TCF4911U Item Rated power supply TCF4901EU TCF4901U TCF4913EU TCF4913U TCF4903EU TCF4903U AC 120 V 60 Hz Rated power consumption 1288 W 1287 W 1288 W 1287 W Maximum power consumption 1444 W 1443 W 1444 W 1443 W Type of water heater Instantaneous type Power cord length 3.94 ft (1.2 m) Water protection level IPX4 Approx. 0.08 to 0.11 gal/min. (Approx. 0.32 to 0.43 L/min.) Approx. 0.08 to 0.11 gal/min. (Approx. 0.32 to 0.
Limited Warranty One Year Limited Warranty Reference 67 M08036_1_EN.
You are advised to record the following information to allow quick service. Date of purchase : Name of shop : Date : year month day Tel : ( ) 2017.8.18 M08036-1 M08036_1_EN.
