User's Guide

360° Microphones
Mute LED
Power LED
Bluetooth LED
360° Microphones
Mute LED
Power LED
Bluetooth LED
For detailed product information, set up procedures and FAQ’s
please visit our website: www.toucansolution.com or scan the QR code.
internal
S100
Bluetooth
S100
successful
connection
• Plug the included USB cable into your computer and
connect the end with the type-C connector to S100.
• Select S100 as the default microphone and speaker source.
Connect S100 to your computer
2
• Press and hold for 2 seconds until the Bluetooth LED
on S100 begins flashing. You will hear connection
guidance voice prompts.
• Enable Bluetooth on your Bluetooth device.
• Select S100 from the list of available Bluetooth devices
to connect.
• You will hear a successful connection message from S100.
• Tap to disconnect with connecting Bluetooth device.
Connect S100 with a Bluetooth Device
3
• Tap while calling to mute or unmute the microphone.
Mute/Unmute
4
Getting Started
• Plug the included power adapter into a power outlet
and connect the other end to S100.
• Press and hold for 1 second to turn S100 on and
2 seconds to turn it off.
Turn on S100
1
1
• Remove the top cover of S100A conference speaker and
snap in C100 conference camera module.
• Plug the included power adapter into a power outlet and
connect the other end to SC100
• Press and hold on the top of the speaker for 1 second
to turn SC100 on and 2 seconds to turn it off.
Turn on SC100
• Plug the included USB cable into your computer and
connect the end with the type-C connector to SC100.
• Select S100A as the default microphone and speaker
source. Select C100 as the default camera source.
Connect SC100 to your computer
2
Bluetooth
S100A
• Press and hold for 2 seconds until the Bluetooth LED on
S100A begins flashing. You will hear connection guidance
voice prompts.
• Enable Bluetooth on your Bluetooth device.
• Select S100A from the list of available Bluetooth devices to
connect.
• You will hear a successful connection message from S100A.
• Tap to disconnect with connecting Bluetooth device.
3
Connect SC100 with a Bluetooth Device (Audio Only)
• Tap while calling to mute or unmute the microphone.
Mute/Unmute
4
• Snap C100 into tripod adapter and attach it to the included
display mount.
• Mount C100 on top of the display and adjust the camera
view to correct position.
• Plug the included USB cable into either USB port at the
bottom of S100A and connect the other end with the
type-C connector to C100
• Select S100A and C100 as the default audio and video
source on your computer
Mount C100 on Display
internal
S100A
internal
C100
Press and hold to turn S100 on/off
Power On/Off
Tap to increase volume
Volume up
Tap to reduce volume
Volume down
Mute
Mute microphone
Tap to mute or unmute microphone
Voice guidance
Press and hold 10s to turn voice guidance on/off
Bluetooth
Connect with new Bluetooth device
Press and hold to enter Bluetooth pairing mode to connect
with a new Bluetooth device
Disconnect or reconnect with Bluetooth device
Tap to disconnect or reconnect with a paired Bluetooth device
For detailed product information, set up procedures and FAQ’s
please visit our website: www.toucansolution.com or scan the QR code.
Getting Started
Press and hold to turn S100 on/off
Power On/Off
Tap to increase volume
Volume up
Tap to reduce volume
Volume down
Mute
Mute microphone
Tap to mute or unmute microphone
Voice guidance
Press and hold 10s to turn voice guidance on/off
Bluetooth
Connect with new Bluetooth device
Press and hold to enter Bluetooth pairing mode to connect
with a new Bluetooth device
Disconnect or reconnect with Bluetooth device
Tap to disconnect or reconnect with a paired Bluetooth device
successful
connection
FCC Statement
Warning: Changes or modifications to this unit not expressly approved by the party responsible for compliance
could void the user’s authority to operate the equipment.
NOTE: This equipemnt has been tested and found to comply with the limits for a Class B digital device, pursuant
to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy
and, if not installed and used in accordance with the instructions, may cause harmful interference to radio
communications.
However, there is no guarantee that interference will not occur in a particular Installation. If this equipment
does cause harmful interference to radio or television reception, which can be determined by turning the
equipment off and on, the user is encouraged to try to correct the interference by one or more of the following
measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) This device may not cause harmful interference.
(2) This device must accept any interference received, including intereference that may cause undesired
operation.
ISED Regulatory Compliance
This device contains licence-exempt transmitter(s)/receiver(s) that comply with Innovation, Science and
Economic Development Canada’s lincence-exempt RSS(s). Operation is subject to the following two
conditions:
1. This device may not cause interference.
2. This device must accept any interference, including interference that may cause undesired operation of
the device.
L’émetteur/récepteur exempt de licence contenu dans le présent appareil est conforme aux CNR d’Innovation,
Sciences et Développement économique Canada applicables aux appareils radio exempts de licence.
L’exploitation est autorisée aux deux conditions suivantes :
1. L’appareil ne doit pas produire de brouillage;
2. L’appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d’en
compromettre le fonctionnement.
RF Exposure Compliance
This equipment complies with FCC/IC radiation exposure limits set forth for an uncontrolled environment.
This equipment should be installed and operated with minimum distance 20cm between the radiator and
your body.
Cet équipement est conforme aux limites d’exposition aux radiations FCC/IC établies pour un environnement
non contrôlé.
Cet équipement doit être installé et utilisé avec une distance minimale de 20 cm entre le radiateur et votre
corps.
Getting to know your
Conference Speaker S100
W1OO
STREAMING
WEBCAM
Thank You for Purchasing
For detailed product information, set up procedures and FAQ’s
please visit our website: www.toucansolution.com or scan the QR code.
Display Mount Streaming Webcam
W100
USB Cable(2m)
Warranty Card User Guide
Getting to know your
Video Conference System HD SC100
1
Install W100 to the
included display mount
or tripod (not included).
Getting to know your
STREAMING WEBCAM W100
Getting Started
What’s in the Box
Camera LED
Microphone
Tripod Thread
Lens
Plug the included USB cable
into your computer and
connect the other end to the
back of W100.
Place W100 on top of the
display and tilt the camera
to right position.
Select W100 as the default
camera and microphone
source on your computer.
internal
W100
42 3
©2022 VUPOINT SOLUTIONS, INC. All Rights Reserved.
The Toucan logo and Toucan are trademarks or registered trademarks of VuPoint Solutions Inc. in the United States and
other countries. All trademarks remain the property of their respective holders, and are used only to describe the
products or services being provided. These trademark holders are not affiliated with VuPoint Solutions, Inc. They do not
sponsor or endorse VuPoint Solutions, Inc’s products or services.
VuPoint Solutions, Inc. (USA):
710 Nogales Street, City of Industry, CA 91748
VuPoint (Europe) Company Limited:
Innovation Center, Longbridge Technology Park,
Longbridge, Birmingham B31 2TS
For additional info, visit our website at www.toucansolution.com
Power Adapter
Warranty Card
USB Cable
User Guide
Conference Speaker
S100
CONFERENCE
SPEAKER
What’s in the Box
Thank You
for Purchasing
FCC Statement
Warning: Changes or modifications to this unit not expressly approved by
the party responsible for compliance could void the user’s authority to
operate the equipment.
NOTE: This equipemnt has been tested and found to comply with the limits
for a Class B digital device, pursuant to Part 15 of the FCC Rules. These
limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates, uses
and can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio
communications.
However, there is no guarantee that interference will not occur in a
particular Installation. If this equipment does cause harmful interference to
radio or television reception, which can be determined by turning the
equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to
which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
This device complies with Part 15 of the FCC Rules. Operation is subject to
the following two conditions:
(1) This device may not cause harmful interference.
(2) This device must accept any interference received, including
intereference that may cause undesired operation.
ISED Regulatory Compliance
This device contains licence-exempt transmitter(s)/receiver(s) that comply
with Innovation, Science and Economic Development Canada’s lincence-ex-
empt RSS(s). Operation is subject to the following two conditions:
1. This device may not cause interference.
2. This device must accept any interference, including interference that
may cause undesired operation of the device.
L’émetteur/récepteur exempt de licence contenu dans le présent appareil est
conforme aux CNR d’Innovation, Sciences et Développement économique
Canada applicables aux appareils radio exempts de licence. L’exploitation est
autorisée aux deux conditions suivantes :
1. L’appareil ne doit pas produire de brouillage;
2. L’appareil doit accepter tout brouillage radioélectrique subi, même si le
brouillage est susceptible d’en compromettre le fonctionnement.
RF Exposure Compliance
This equipment complies with FCC/IC radiation exposure limits set forth for
an uncontrolled environment.
This equipment should be installed and operated with minimum distance
20cm between the radiator and your body.
Cet équipement est conforme aux limites d’exposition aux radiations FCC/IC
établies pour un environnement non contrôlé.
Cet équipement doit être installé et utilisé avec une distance minimale de 20
cm entre le radiateur et votre corps.
©2022 VUPOINT SOLUTIONS, INC. All Rights Reserved.
The Toucan logo and Toucan are trademarks or registered trademarks of VuPoint Solutions
Inc. in the United States and other countries. The Bluetooth® word mark and logos are
registered trademarks owned by Bluetooth SIG, Inc. Product names, logos, brands and other
trademarks referred to herein are the property of their respective trademark holders. All
trademarks remain the property of their respective holders, and are used only to describe the
products or services being provided. These trademark holders are not affiliated with VuPoint
Solutions, Inc. They do not sponsor or endorse VuPoint Solutions, Inc’s products or services.
VuPoint Solutions, Inc. (USA):
710 Nogales Street, City of Industry, CA 91748
VuPoint (Europe) Company Limited:
Innovation Center, Longbridge Technology Park,
Longbridge, Birmingham B31 2TS
For additional info, visit our website at www.toucansolution.com
User Guide
Warranty Card
USB Cable(3m) x1
USB Cable(2m) x1
Tripod Adapter
Power Adapter
Display Mount
VIDEO
CONFERENCE
SYSTEM HD
What’s in the Box
Conference Speaker
S100A
Conference Camera
C100
Thank You
for Purchasing
FCC Statement
Warning: Changes or modifications to this unit not expressly approved by
the party responsible for compliance could void the user’s authority to
operate the equipment.
NOTE: This equipemnt has been tested and found to comply with the limits
for a Class B digital device, pursuant to Part 15 of the FCC Rules. These
limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates, uses
and can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio
communications.
However, there is no guarantee that interference will not occur in a
particular Installation. If this equipment does cause harmful interference to
radio or television reception, which can be determined by turning the
equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to
which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
This device complies with Part 15 of the FCC Rules. Operation is subject to
the following two conditions:
(1) This device may not cause harmful interference.
(2) This device must accept any interference received, including
intereference that may cause undesired operation.
ISED Regulatory Compliance
This device contains licence-exempt transmitter(s)/receiver(s) that comply
with Innovation, Science and Economic Development Canada’s lincence-ex-
empt RSS(s). Operation is subject to the following two conditions:
1. This device may not cause interference.
2. This device must accept any interference, including interference that
may cause undesired operation of the device.
L’émetteur/récepteur exempt de licence contenu dans le présent appareil est
conforme aux CNR d’Innovation, Sciences et Développement économique
Canada applicables aux appareils radio exempts de licence. L’exploitation est
autorisée aux deux conditions suivantes :
1. L’appareil ne doit pas produire de brouillage;
2. L’appareil doit accepter tout brouillage radioélectrique subi, même si le
brouillage est susceptible d’en compromettre le fonctionnement.
RF Exposure Compliance
This equipment complies with FCC/IC radiation exposure limits set forth for
an uncontrolled environment.
This equipment should be installed and operated with minimum distance
20cm between the radiator and your body.
Cet équipement est conforme aux limites d’exposition aux radiations FCC/IC
établies pour un environnement non contrôlé.
Cet équipement doit être installé et utilisé avec une distance minimale de 20
cm entre le radiateur et votre corps.
©2022 VUPOINT SOLUTIONS, INC. All Rights Reserved.
The Toucan logo and Toucan are trademarks or registered trademarks of VuPoint Solutions
Inc. in the United States and other countries. The Bluetooth® word mark and logos are
registered trademarks owned by Bluetooth SIG, Inc. Product names, logos, brands and other
trademarks referred to herein are the property of their respective trademark holders. All
trademarks remain the property of their respective holders, and are used only to describe the
products or services being provided. These trademark holders are not affiliated with VuPoint
Solutions, Inc. They do not sponsor or endorse VuPoint Solutions, Inc’s products or services.
VuPoint Solutions, Inc. (USA):
710 Nogales Street, City of Industry, CA 91748
VuPoint (Europe) Company Limited:
Innovation Center, Longbridge Technology Park,
Longbridge, Birmingham B31 2TS
For additional info, visit our website at www.toucansolution.com