User's Manual

ManualsBrandsTouchtronics ManualsElectronicsKeyless Entry RFID Reader

ARMING AND DISARMING THE SECURITY SYSTEM

Arming the Security System

a. Truck is armed anytime all doors are closed.

b. Cargo compartment is armed anytime BOTH doors are closed.

Disarming the Security System

a. Wristband Key is presented to any Antenna or the Keyless Start unit and doors are

closed.

b. Pressing any Unlock switch just prior to opening the corresponding door.

Alarm Triggered

a. If the alarm is triggered, the siren will sound and the dome light

s will flash.

b. The Doors

Ajar LED will flash until the Keyless Start detects a valid Wristband Key.

Disarming the Security System if the

Alarm is Triggered

a. Wristband Key is presented to any door or the Keyless Start unit.

b. Truck ignition is on.

c. Master Key is presented to any Antenna or the Keyless Start unit.

57315 Nagy Drive W

arranty

Elkhart, IN 46517 &

Fax: 574-293-1611 Technical Support

www.touchtronics.com 574-294-2570

T O U C H T R O N I C S, I N C.

KEYLESS START STATUS LEDs

a. The red Doors Ajar LED will turn on solid anytime the driv-

er, bulkhead or rear doors are open and the truck is off. The

red Doors Ajar LED will flash if the alarm has been triggered.

b. The green Run LED will be on solid anytime the truck is running.

The green Run LED will flash when a valid Wristband Key is authorized

until the Engine Start button is pressed or will timeout at 25 seconds.

c. The yellow Start LED will be on solid when Engine Start button is pressed and the engine can be started.

The yellow Start LED will flash if the Engine Start button is pressed and the engine can’t be started due to a

failed door switch or antenna connector.

d. The red CK SYS LED will flash twice anytime a valid Wristband Key is presented. The red CK SYS LED

will flash continuously during start-up mode if there is a system failure at any antenna. If the truck enters

sleep mode, the CK SYS LED will flash at 5-second ratio until truck exits sleep mode.

KEYLESS STARTING & STOPPING

a. Close the driver, bulkhead and rear doors.

b. Swipe the authorized Wristband Key across the target area on the left side of the

Keyless Start unit.

c. The red CK SYS LED will flash twice, which indicates a valid Wristband Key has been received

and the Keyless Start unit will turn on. The green Run LED will flash for 25 seconds indicating the

truck is ready to be started and the switch backlights will also be on.

d. Check the Doors Ajar LED on the Keyless Start unit. If it is off, then proceed with starting the

truck. If the Doors Ajar status LED is on, then close the driver, bulkhead and/or rear door.

e. Wait for the glow plug indicator light on the dash to turn off and then press the Start switch

marked “ENGINE START”. The yellow Start LED turns on solid indicating the truck starter has been

energized. Release the Engine Start switch as soon as the truck engine is started.

f. To stop the truck and turn off the engine, press the “ENGINE STOP” switch. The engine will turn

off and all of the status LEDs will turn off.

TouchTronics assumes no responsibility for any errors that may appear in this manual. Information contained herein is subject to change without notice.

FCC Compliance and

Advisory Statement. This hardware device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: 1) this

device may not cause harmful interference, and 2) this device must accept any interference received, including interference that may cause undesired operation. Any

changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

Canadian Compliance S

atement. This device complies with RSS-210 of Industry Canada. Operation is subject to the following two conditions: 1) this device may not

cause interference, and 2) this device must accept any interference, including interference that may cause undesired operation of the device.

TouchTronics et sont susceptibles d’être des marques déposées. Toutes les autres marques sont la propriété exclusive de leurs détenteurs respectifs. TouchTronics

décline toute responsabilité en cas d’erreurs dans ce manuel. Les informations énoncées dans le présent document peuvent faire l’objet de modifications sans avis préal-

able.

Déclaration FCC. Cet équipement a été testé et déclaré conforme à la section 15 du règlement de la FCC. Son fonctionnement est soumis aux conditions suivantes: 1)

l’équipement concerné ne doit pas causer d’interférences dangereuses, et 2) il doit accepter toute interférence reçue, y compris les interférences risquant d’engendrer un

fonctionnement indésirable. Toutes modifications ou tous changements effectués sans l’accord exprès de la partie responsable de la conformité aux normes pourraient

contraindre l’utilisateur à ne plus utiliser son équipement.

Déclaration du Ministère des Communications Canadien. Cet équipement a été déclaré conforme à la norme RSS-210 édictée p

ar le Ministère canadien de l’industrie.

Son fonctionnement est soumis aux conditions suivantes: 1) l’équipement concerné ne doit pas causer d’interférences, et 2) il doit accepter toute interférence reçue, y

compris les interférences risquant d’engendrer un fonctionnement indésirable.