Type designation RS series has several types. The types are shown on the model label as follows: MODEL/MODELE(MODEL NAME) SERIES/SERIE RS SERIES/SERIE RS2000 SERIES/SERIE RS2000A SERIES/SERIE RS2000B SERIES/SERIE Model label When calling for service, please note the MODEL and SERIES numbers that are inscribed on the back of your sewing machine.
CONTENTS I. Before use .............................................................................................. 3 1. Important safety instructions.......................................................................... 3 2. How to change the power plug ...................................................................... 5 3. Part names .................................................................................................... 6 II. Sewing preparations ....................................
Before use I. Before use Be sure to read this section before use 1. Important safety instructions These safety instructions are designed to prevent danger or damage arising from the incorrect operation of the machine. Read carefully and always follow the instructions. Explanation of " " and " " An incorrect operation could result in death or serious injury. An incorrect operation could result in an injury or damage to the machine.
Before use When the machine is not in use it should be stored safely, not on the floor as protruding parts could cause injury if a person fell on the machine. Not doing so could cause an injury. Use with the shuttle cover closed. Not doing so could cause an injury. Before replacing the needle or presser foot or when threading the upper or lower thread, remove the power plug from the outlet. Not doing so could cause an injury. Do not look away from the needle while operating the sewing machine.
Before use UK ONLY IMPORTANT PLEASE READ CAREFULLY 2. How to change the power plug When you change the power plug or cord, do not repair, disassemble or modify except at the authorised dealeror service centre. Doing so could cause an electric shock or a fire. If for any reason the power plug for this product is removed it should be immediately disposed of safety and not stored anywhere where it could be inadvertently used again. Doing so could cause an electric shock or a fire.
Before use 3. Part names Some parts may not apply to your sewing machine. The MODEL and SERIES numbers are located on the model label on the back of the sewing machine. 使使 Front pattern selection dial type 使使 Part name Detail by use Upper thread tension dial Refer to P.30 [Adjusting thread tension] Spool pin Refer to P.13 [Winding the lower thread] Reverse sewing lever Refer to P.
Before use Part name Detail by use Declutch knob Refer to P.14[Winding the lower thread] 4) Buttonhole adjustment screw Refer to P.36 [侀Adjustment of buttonhole balance侀] Presser foot lever Refer to P.
Before use Some parts may not apply to your sewing machine. The MODEL and SERIES numbers are located on the model label on the back of the sewing machine. 使使 Side pattern selection dial type 使使 Part name Detail by use Upper thread tension dial Refer to P.30 [Adjusting thread tension] Spool pin Refer to P.13 [Winding the lower thread] Reverse sewing lever Refer to P.
Before use Part name Detail by use Declutch knob Refer to P.14[Winding the lower thread] 4) Buttonhole adjustment screw Refer to P.36 [侀Adjustment of buttonhole balance侀] Presser foot lever Refer to P.
Sewing preparations II. Sewing preparations 1. Connecting the power 使使 Machine with a power switch 使使 Turn the power switch off when inserting the power plug. Not doing so could cause an injury. Hold the power plug when removing it from the outlet. Not doing so could damage the cord and cause an electric shock, fire or injury. Do not touch the power plug with wet hands. Doing so could cause an electric shock. Prepare the foot controller. Insert the power cord connector into the terminal box.
Sewing preparations 使使 Machine without a power switch 使使 RS2000 A/B series only. Hold the power plug when removing it from the outlet. Not doing so could damage the cord and cause an electric shock, fire or injury. Do not touch the power plug with wet hands. Doing so could cause an electric shock. Prepare the foot controller. Insert the power cord connector into the terminal box. Insert the power plug into the outlet. The power is turned on at the outlet.
Sewing preparations 2. Taking out the bobbin Before taking out or setting the bobbin case, remove the power plug from the outlet. Not doing so could cause an injury. 1. Turn the handwheel to move the needle to the highest position. Always turn the handwheel towards yourself. (in the direction of the arrow) 2. Hold the left edge of the extension table and pull out to the left. (in the direction of the arrow) Open the shuttle cover. (Open out in the direction of the arrow.
Sewing preparations 3. Winding the lower thread Before taking out or setting the bobbin case, remove the power plug from the outlet. Not doing so could cause an injury. Do not touch the lower thread winding spindle when winding the lower thread. Not doing so could cause an injury. Attention Use a TOYOTA-exclusive bobbin. Remove the sticker. Pull up the spool pin from the sewing machine. 1. Turn the pin around and insert. 2. Insert the thread spool.
Sewing preparations 1. Move the declutch latch in the direction (in the direction of the arrow) (This ensures that the needle does not move.) 2. Pass the thread from the inside through the bobbin hole. 3. Set the bobbin on the thread winding spindle and move the spindle to the right (in the direction of the arrow) 1. Holding the end of the thread, step on the foot controller to wind the thread. 2. After winding it a little, stop the sewing machine and cut the thread that protrudes from the bobbin hole.
Sewing preparations 4. Threading the lower thread Before setting the bobbin case, remove the power plug from the outlet. Not doing so could cause an injury. Attention Use a TOYOTA-exclusive bobbin. Take out the bobbin case. (refer to P.12 [Taking out the bobbin]) The thread must flow off the bobbin in the direction of the arrow, and then insert the bobbin into the bobbin case. Hold the end of the thread in your right hand and pass it through the groove in the bobbin case.
Sewing preparations 5. Threading the upper thread Before threading the upper thread, remove the power plug from the outlet. Not doing so could cause an injury. Raise the presser foot lever. Note: If the presser foot lever is not raised, the thread cannot be set correctly. Pull out the spool pin from the main unit. 1. Turn the spool pin over and insert. 2. Insert the thread spool.
Sewing preparations Support the thread on the sewing machine with one hand, using the other hand pass the thread around the thread guide as shown in the diagram. Pass the thread between the thread guide plate and the tension disc. Pass the thread along the groove of the thread guide plate. Turn the handwheel towards yourself until the take-up lever is visible. Pass the thread through the take-up lever. Set the thread on the left side of the needle guide.
Sewing preparations 6. Pulling up the lower thread Hold the end of the thread, turn the handwheel towards yourself for one full turn, and stop when the needle is at its highest position. Note : Always turn the handwheel towards yourself. (in the direction of the arrow) If you turn it in the reverse direction it could tangle the thread. Note : If the thread is tight the lower thread will not come out, so hold the thread loosely. Pull the upper thread and the loop of the lower thread will come out.
Sewing preparations 7. Main stitch pattern uses Depending on the model of your sewing machine, some of the stitch patterns are not available. (refer to P.
Sewing preparations 8. Application of each stitch pattern Do not turn the pattern selection dial while operating the sewing machine. Doing so could cause an injury. Attention The number of stitch patterns may differ from model to model. The model number is located on the model label on the back of the sewing machine.
Sewing preparations 9. Changing the presser foot Before changing the presser foot, remove the power plug from the outlet. Not doing so could cause an injury. 侀 Removal 侀 1. Raise the presser foot lever. 2. Turn the handwheel towards yourself to raise the needle.
Sewing preparations 侀 Installation 侀 Position the presser foot pin directly below the groove in the presser foot holder. Lower the presser foot lever to set the presser foot.
Sewing preparations 10. Changing the needle Before changing the needle, remove the power plug from the outlet. Not doing so could cause an injury. Broken needles are dangerous. Be sure to dispose of them in a safe place away from children. Not doing so could cause an injury. 1. Turn the handwheel towards yourself to raise the end of the needle higher than the needle plate. 2. Hold the needle in one hand, loosen the needle clamp screw with the accessory needle plate screw driver, and remove the needle.
Sewing preparations 11. Relationship between the needle, thread and fabric, and adjusting the sewing machine The quality of the sewing finish will improve if the needle and thread are changed to match the type of fabric. Follow the directions in the table below. Use a ball point needle for the sewing alignment of stretch fabric. Please purchase any needles not included as accessories, after checking they are specifi ed as home-use sewing machine needles. Refer to P.
Sewing III. Sewing 1. Straight stitching and reverse sewing Reverse sewing is performed at the beginning and end of sewing to prevent the thread from unraveling. Do not pull the fabric excessively while sewing. Doing so could break the needle and cause an injury. 侀 Straight stitch 侀 1. Turn the handwheel towards yourself to raise the needle. 2. Turn the pattern selection dial to choose the pattern. Set the fabric and lower the presser foot lever. Step on the foot controller to begin sewing.
Sewing 侀 Thread cutter on the needle bar 侀 * The thread cutter may differ from model to model. Line up two threads and cut with the thread cutter on the needle bar. 侀 Thread cutter on the face cover 侀 * The thread cutter may differ from model to model. Line up two threads and cut with the thread cutter on the face cover. 侀 Reverse sewing 侀 Reverse sewing is performed at the beginning and end of sewing to prevent the thread from unraveling.
Sewing 侀 Sewing thick fabric 侀 When sewing thick fabric from the edge, the presser foot may tilt and be unable to feed through the fabric. Place fabric or thick paper of the same thickness as the fabric you wish to sew under the presser foot. This will enable smooth sewing. 侀 Sewing thin fabric 侀 Sewing is easier if thin paper is laid out under the fabric.
Sewing 侀 Sewing tube-shaped fabrics 侀 Pull out the extension table (accessory box) in the direction of the arrow. Sew tube-shaped fabrics such as trousers or sleeves.
Sewing 2. Zigzag sewing There are various types of zigzag sewing methods, such as applique and overcastting. Turn the handwheel towards yourself to raise the needle. Turn the pattern selection dial to choose the pattern. Set the fabric and lower the presser foot. Step on the foot controller to begin sewing.
Sewing 3. Adjusting thread tension Before adjustment, check again that "P.16 [Threading the upper thread]" has been performed correctly. 侀 Adjustment method for upper thread tension 侀 Upper thread is tight Turn down the upper thread tension dial. Upper thread is loose Turn up the upper thread tension dial. Note : If the tension does not change even when you turn the upper thread tension dial, reset the upper thread. Note : If it does not change with the upper thread, adjust the lower thread.
Sewing 4. Overcasting This is a sewing method that prevents unraveling at the edge of the fabric. Is not available for 16/18 stitch model. (refer to P.20 [Application of each stitch pattern]) Position the fabric so that the right needle entry point at the edge of the fabric is slightly on the outside. It is easier to sew accurately if an overcasting foot is used. (Optional Accessory).
Sewing 5. Blind hem stitching In this sewing method the stitch cannot be seen on the right side of the fabric. Fold back the fabric so that the folded area protrudes by about 5 to 7mm. Iron and tack by hand. Position the fabric so that the needle slightly catches the fold when the needle moves to the left. Lower the presser foot and start sewing. The part of the stitch that catches the fold will be visible from the right side of the fabric.
Sewing It is easier to sew accurately if a blind stitch foot is used.
Sewing 6. Buttonhole Before changing the presser foot, remove the power plug from the outlet. Not doing so could cause an injury. Buttonhole sewing to match the size of the button is possible. For stretch fabric or thin fabric, a fusible interlining on the wrong side of the fabric will reinforce the fabric and produce a good finish for the buttonhole. Change to the buttonhole foot. (refer to P.21 [Changing the presser foot]) Set the buttonhole size and mark a line on the fabric.
Sewing Align the buttonhole foot division line closest to you with the guide line, and lower the presser foot to the start line of sewing on the fabric. Raise the needle to the highest position, set the pattern dial to "1", and sew 5 to 6 bar-tack stitches. Raise the needle to the highest position, set the pattern dial to "2", sew the left side and stop at the line marked on the fabric. Raise the needle to the highest position, set the pattern dial to "3", and sew 5 to 6 bar-tack stitches.
Sewing When using the buttonhole cutter to cut the buttonholes, do not hold the fabric in front of the cutter. Doing so could cause an injury to your hand. Use the buttonhole cutter to cut the center, making sure not to cut the stitches. Note : If a marking pin is put in the bar-tack area it helps to prevent excessive cutting with the buttonhole cutter. 侀 Adjustment of buttonhole balance 侀 Use the buttonhole adjustment screw to adjust the balance between the stitches.
Sewing 7. Zipper sewing Before changing the presser foot, remove the power plug from the outlet. Not doing so could cause an injury. Change to the zipper foot. (refer to P.21 [Changing the presser foot]) 侀 Sewing the left side of the zipper 侀 1. Set the zipper foot to the right side pin. 2. Align the zipper and the fabric, and tack. Position the fabric so that the zipper is on the right side of the presser foot.
Sewing Sew until just before the presser foot makes contact with the slider, and then stop the sewing machine. Turn the handwheel towards yourself to lower the needle into the fabric. Raise the presser foot lever. Move the slider to the rear of the presser foot, and sew the remainder. 侀 Sewing the right side of the zipper 侀 Release the presser foot and set to the left side pin. Sew the right side of the zipper using the same procedures as for the left side.
Sewing 8. Smocking Is not available for 16/18 stitch model. (refer to P.20 [Application of each stitch pattern]) To make the gathering: Set the pattern selection dial to "8". Loosen the tension of the upper thread and sew. After sewing, hold the ends of the lower thread as shown in the diagram, and pull up the fabric in the direction of the arrow to make the gathering. After making the gathering, sew the smocking between 2 rows of gathering.
Sewing 9. Embroidery Before setting the darning adapter, remove the power plug from the outlet. Not doing so could cause an injury. A free machine embroidery pattern can be created. Trace your design on the material and centre it in an embroidery hoop. Lay stabilizer underneath thin fabric. Install a darning adapter and then sew. For model 7140, DE21 use the drop feed that comes with the sewing machine instead of a darning adapter. (refer to P.
Sewing Loosen the presser foot holder screw with the needle plate screw driver to release the holder. Firmly stretch the fabric with the design and set in the embroidery hoop. Note : Purchase a commercially available embroidery hoop. At the start of sewing, prepare by sewing one stitch, pulling the upper thread, and pulling out the lower thread above the fabric. Hold the upper and lower threads then make 2-3 stitches, snip off excess threads.
Special specifications IV. Special specifications 1. Using the needle threader Before using the needle threader, remove the power plug from the outlet. Not doing so could cause an injury. Turn the handwheel towards yourself to raise the needle to the highest position. (in the direction of the arrow) Note : Always turn the handwheel towards yourself. If you turn it in the reverse direction it could tangle the thread. Lower the presser foot lever.
Special specifications Hold the thread set in the hook guide to the right side and insert in the needle threader groove. While raising the needle threader lever, remove your hand from the thread. The thread is pulled by the hook and is passed through the eye of the needle as shown in the diagram. Pull out the loop of the upper thread to the rear. Note 1 : If the needle is not set correctly, it is not possible to pass the thread through the needle with the needle threader. Refer to P.
Special specifications 2. Using the presser foot pressure adjuster The presser foot pressure adjuster may differ from model to model. 侀 Push-down type 侀 Sewing normal fabric and thick fabric: For normal straight or zigzag sewing, press down "A". Sewing thin fabric: Push down outer ring "B" to pop out pin "A". Push down pin "A" about half way. 侀 Rotary type 侀 Sewing normal fabric and thick fabric: Dial: Align "3" with the upper surface of the face cover.
Special specifications 3. Using the drop feed Before using the drop feed lever, remove the power plug from the outlet. Not doing so could cause an injury. The feed dog can be lowered when feeding the fabric freely by hand, for example, when embroidering or quilting. Model 7140, DE21 only. Make sure the needle and the presser foot are both in the raised position. To lower the feed dog, push the lever back and to the left, to disengage the feed dog.
Maintenance V. Maintenance 1. Feed dog and hook maintenance If the sewing machine makes a loud noise or rotates slowly, the oil could have run out, or there could be thread waste or dust in the hook or feed dog. Clean and oil the hook and feed dog. Before cleaning the hook, remove the power plug from the outlet. Not doing so could cause an injury. Attention Do not use detergent, bleach, benzine, or thinner chemical cloths. Doing so could cause discoloration or cracking.
Maintenance Open the left and right stoppers to the outside. (in the direction of the arrow.) Take out the shuttle hook cover. Take out the shuttle hook. Wipe the shuttle race clean with a brush or soft cloth. Apply one drop of oil to the shuttle race. Note 1: If too much oil is applied it could cause trouble such as dirty thread or bobbins, or sewing malfunctions. Keep to this small amount. Note 2: Use the oil supplied with your machine or special oil for sewing machines.
Maintenance 2. Hook installation The hook is installed by reversing the removal procedures. Replace the shuttle hook. Align the projection of the shuttle hook cover with the depression of the hook, and install the shuttle hook cover. Close the left and right stoppers to the inside. (in the direction of the arrow) Hold the latch of the bobbin case and insert the bobbin case into the shuttle race. The bobbin case finger must slot into the groove.
Maintenance 3. Light bulb replacement Light bulb is not equipped with RS2000B series. Before changing the light bulb, remove the power plug from the outlet and wait until the bulb cools. Not doing so could cause a burn or electric shock. Loosen the screw and take off the face cover. Turn the light bulb counterclockwise and remove. Turn the new light bulb clockwise to install. Note : Use a light bulb with a maximum power of 15W. Always reinstall the face cover after replacing the light bulb.
Maintenance 4. Troubleshooting What is the problem? Check the following possibilities before taking the sewing machine in for repair.
Maintenance Trouble Missed stitches The fabric wrinkles Too much lower thread appears on the right side of the fabric Too much upper thread appears on the wrong side of the fabric Needle threader does not work Cause Countermeasure Page The needle is not correctly installed Install the needle correctly 23 The needle is bent Replace with a straight needle 23 The needle and thread are not appropriate for the fabric Sew with a needle and thread appropriate to the fabric 24 The upper thread is
Others VI. Others 1. Specifications Model RS2000-SDU Type Hook type Vertical, oscillating hook Needle Home-use sewing machine needle (HA-1) Bobbin TOYOTA-exclusive plastic bobbin Maximum stitch length 5 mm Maximum stitch width 5 mm Standard needle position Center standard, left standard Sewing machine weight (main unit) 6.
Others 53